| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
To support compilation with Media controller disabled, drivers were
required to conditionally call media_device_init and media_device_cleanup.
Add nop implementations of both so drivers don't need to care (or at least
care less).
Signed-off-by: Sakari Ailus <[email protected]>
Acked-by: Hans Verkuil <[email protected]>
Signed-off-by: Hans Verkuil <[email protected]>
|
|
LoongArch will override page_to_virt() which use page_address() in the
KFENCE case (by defining WANT_PAGE_VIRTUAL/HASHED_PAGE_VIRTUAL). So move
lowmem_page_address() a little later to avoid such build errors:
error: implicit declaration of function 'page_address'.
Acked-by: Andrew Morton <[email protected]>
Signed-off-by: Huacai Chen <[email protected]>
|
|
gma_drm.h has become an empty, unused header. Remove.
Cc: Patrik Jakobsson <[email protected]>
Reviewed-by: Javier Martinez Canillas <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
Signed-off-by: Jani Nikula <[email protected]>
|
|
Add reset id used for HDMI Receiver in RK3588 SoCs
Acked-by: Rob Herring <[email protected]>
Signed-off-by: Shreeya Patel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Heiko Stuebner <[email protected]>
|
|
The USB480M clock can source from a MUX that selects the clock to come
from either of the USB-phy internal 480MHz PLLs. These clocks are
provided by the USB phy driver. This adds the define for it.
Signed-off-by: Sascha Hauer <[email protected]>
Acked-by: Krzysztof Kozlowski <[email protected]>
Link: https://lore.kernel.org/r/20240405-clk-rk3568-usb480m-phy-mux-v1-1-6c89de20a6ff@pengutronix.de
Signed-off-by: Heiko Stuebner <[email protected]>
|
|
Architectures are required to provide four-byte cmpxchg() and 64-bit
architectures are additionally required to provide eight-byte cmpxchg().
However, there are cases where one-byte cmpxchg() would be extremely
useful. Therefore, provide cmpxchg_emu_u8() that emulates one-byte
cmpxchg() in terms of four-byte cmpxchg().
Note that this emulations is fully ordered, and can (for example) cause
one-byte cmpxchg_relaxed() to incur the overhead of full ordering.
If this causes problems for a given architecture, that architecture is
free to provide its own lighter-weight primitives.
[ paulmck: Apply Marco Elver feedback. ]
[ paulmck: Apply kernel test robot feedback. ]
[ paulmck: Drop two-byte support per Arnd Bergmann feedback. ]
Link: https://lore.kernel.org/all/0733eb10-5e7a-4450-9b8a-527b97c842ff@paulmck-laptop/
Signed-off-by: Paul E. McKenney <[email protected]>
Acked-by: Marco Elver <[email protected]>
Cc: Andrew Morton <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Cc: "Peter Zijlstra (Intel)" <[email protected]>
Cc: Douglas Anderson <[email protected]>
Cc: Petr Mladek <[email protected]>
Cc: Arnd Bergmann <[email protected]>
Cc: <[email protected]>
|
|
It was unnecessarily disabling and enabling PMUs for each event. It
should be done at PMU level. Add pmu_ctx->nr_freq counter to check it
at each PMU. As PMU context has separate active lists for pinned group
and flexible group, factor out a new function to do the job.
Another minor optimization is that it can skip PMUs w/ CAP_NO_INTERRUPT
even if it needs to unthrottle sampling events.
Signed-off-by: Namhyung Kim <[email protected]>
Signed-off-by: Ingo Molnar <[email protected]>
Tested-by: Mingwei Zhang <[email protected]>
Reviewed-by: Ian Rogers <[email protected]>
Reviewed-by: Kan Liang <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
With the changes in the last patches, napi_frag_unref() is now
reduandant. Remove it and use skb_page_unref directly.
Signed-off-by: Mina Almasry <[email protected]>
Reviewed-by: Dragos Tatulea <[email protected]>
Reviewed-by: Eric Dumazet <[email protected]>
Reviewed-by: Jacob Keller <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
The implementations of these 2 functions are almost identical. Remove
the implementation of napi_frag_unref, and make it a call into
skb_page_unref so we don't duplicate the implementation.
Signed-off-by: Mina Almasry <[email protected]>
Reviewed-by: Eric Dumazet <[email protected]>
Reviewed-by: Jacob Keller <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Although ipv6_get_ifaddr walks inet6_addr_lst under the RCU lock, it
still means hlist_for_each_entry_rcu can return an item that got removed
from the list. The memory itself of such item is not freed thanks to RCU
but nothing guarantees the actual content of the memory is sane.
In particular, the reference count can be zero. This can happen if
ipv6_del_addr is called in parallel. ipv6_del_addr removes the entry
from inet6_addr_lst (hlist_del_init_rcu(&ifp->addr_lst)) and drops all
references (__in6_ifa_put(ifp) + in6_ifa_put(ifp)). With bad enough
timing, this can happen:
1. In ipv6_get_ifaddr, hlist_for_each_entry_rcu returns an entry.
2. Then, the whole ipv6_del_addr is executed for the given entry. The
reference count drops to zero and kfree_rcu is scheduled.
3. ipv6_get_ifaddr continues and tries to increments the reference count
(in6_ifa_hold).
4. The rcu is unlocked and the entry is freed.
5. The freed entry is returned.
Prevent increasing of the reference count in such case. The name
in6_ifa_hold_safe is chosen to mimic the existing fib6_info_hold_safe.
[ 41.506330] refcount_t: addition on 0; use-after-free.
[ 41.506760] WARNING: CPU: 0 PID: 595 at lib/refcount.c:25 refcount_warn_saturate+0xa5/0x130
[ 41.507413] Modules linked in: veth bridge stp llc
[ 41.507821] CPU: 0 PID: 595 Comm: python3 Not tainted 6.9.0-rc2.main-00208-g49563be82afa #14
[ 41.508479] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996)
[ 41.509163] RIP: 0010:refcount_warn_saturate+0xa5/0x130
[ 41.509586] Code: ad ff 90 0f 0b 90 90 c3 cc cc cc cc 80 3d c0 30 ad 01 00 75 a0 c6 05 b7 30 ad 01 01 90 48 c7 c7 38 cc 7a 8c e8 cc 18 ad ff 90 <0f> 0b 90 90 c3 cc cc cc cc 80 3d 98 30 ad 01 00 0f 85 75 ff ff ff
[ 41.510956] RSP: 0018:ffffbda3c026baf0 EFLAGS: 00010282
[ 41.511368] RAX: 0000000000000000 RBX: ffff9e9c46914800 RCX: 0000000000000000
[ 41.511910] RDX: ffff9e9c7ec29c00 RSI: ffff9e9c7ec1c900 RDI: ffff9e9c7ec1c900
[ 41.512445] RBP: ffff9e9c43660c9c R08: 0000000000009ffb R09: 00000000ffffdfff
[ 41.512998] R10: 00000000ffffdfff R11: ffffffff8ca58a40 R12: ffff9e9c4339a000
[ 41.513534] R13: 0000000000000001 R14: ffff9e9c438a0000 R15: ffffbda3c026bb48
[ 41.514086] FS: 00007fbc4cda1740(0000) GS:ffff9e9c7ec00000(0000) knlGS:0000000000000000
[ 41.514726] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 41.515176] CR2: 000056233b337d88 CR3: 000000000376e006 CR4: 0000000000370ef0
[ 41.515713] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 41.516252] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 41.516799] Call Trace:
[ 41.517037] <TASK>
[ 41.517249] ? __warn+0x7b/0x120
[ 41.517535] ? refcount_warn_saturate+0xa5/0x130
[ 41.517923] ? report_bug+0x164/0x190
[ 41.518240] ? handle_bug+0x3d/0x70
[ 41.518541] ? exc_invalid_op+0x17/0x70
[ 41.520972] ? asm_exc_invalid_op+0x1a/0x20
[ 41.521325] ? refcount_warn_saturate+0xa5/0x130
[ 41.521708] ipv6_get_ifaddr+0xda/0xe0
[ 41.522035] inet6_rtm_getaddr+0x342/0x3f0
[ 41.522376] ? __pfx_inet6_rtm_getaddr+0x10/0x10
[ 41.522758] rtnetlink_rcv_msg+0x334/0x3d0
[ 41.523102] ? netlink_unicast+0x30f/0x390
[ 41.523445] ? __pfx_rtnetlink_rcv_msg+0x10/0x10
[ 41.523832] netlink_rcv_skb+0x53/0x100
[ 41.524157] netlink_unicast+0x23b/0x390
[ 41.524484] netlink_sendmsg+0x1f2/0x440
[ 41.524826] __sys_sendto+0x1d8/0x1f0
[ 41.525145] __x64_sys_sendto+0x1f/0x30
[ 41.525467] do_syscall_64+0xa5/0x1b0
[ 41.525794] entry_SYSCALL_64_after_hwframe+0x72/0x7a
[ 41.526213] RIP: 0033:0x7fbc4cfcea9a
[ 41.526528] Code: d8 64 89 02 48 c7 c0 ff ff ff ff eb b8 0f 1f 00 f3 0f 1e fa 41 89 ca 64 8b 04 25 18 00 00 00 85 c0 75 15 b8 2c 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 7e c3 0f 1f 44 00 00 41 54 48 83 ec 30 44 89
[ 41.527942] RSP: 002b:00007ffcf54012a8 EFLAGS: 00000246 ORIG_RAX: 000000000000002c
[ 41.528593] RAX: ffffffffffffffda RBX: 00007ffcf5401368 RCX: 00007fbc4cfcea9a
[ 41.529173] RDX: 000000000000002c RSI: 00007fbc4b9d9bd0 RDI: 0000000000000005
[ 41.529786] RBP: 00007fbc4bafb040 R08: 00007ffcf54013e0 R09: 000000000000000c
[ 41.530375] R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
[ 41.530977] R13: ffffffffc4653600 R14: 0000000000000001 R15: 00007fbc4ca85d1b
[ 41.531573] </TASK>
Fixes: 5c578aedcb21d ("IPv6: convert addrconf hash list to RCU")
Reviewed-by: Eric Dumazet <[email protected]>
Reviewed-by: David Ahern <[email protected]>
Signed-off-by: Jiri Benc <[email protected]>
Link: https://lore.kernel.org/r/8ab821e36073a4a406c50ec83c9e8dc586c539e4.1712585809.git.jbenc@redhat.com
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
copy_from_sockptr() helper is unsafe, unless callers
did the prior check against user provided optlen.
Too many callers get this wrong, lets add a helper to
fix them and avoid future copy/paste bugs.
Instead of :
if (optlen < sizeof(opt)) {
err = -EINVAL;
break;
}
if (copy_from_sockptr(&opt, optval, sizeof(opt)) {
err = -EFAULT;
break;
}
Use :
err = copy_safe_from_sockptr(&opt, sizeof(opt),
optval, optlen);
if (err)
break;
Signed-off-by: Eric Dumazet <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Now that EVM supports RSA signatures for previously completely
unsupported filesystems rename the flag SB_I_EVM_UNSUPPORTED to
SB_I_EVM_HMAC_UNSUPPORTED to reflect that only HMAC is not supported.
Suggested-by: Amir Goldstein <[email protected]>
Suggested-by: Mimi Zohar <[email protected]>
Signed-off-by: Stefan Berger <[email protected]>
Acked-by: Amir Goldstein <[email protected]>
Signed-off-by: Mimi Zohar <[email protected]>
|
|
On stacked filesystem the metadata inode may be different than the one
file data inode and therefore changes to it need to be detected
independently. Therefore, store the i_version, device number, and inode
number associated with the file metadata inode.
Implement a function to detect changes to the inode and if a change is
detected reset the evm_status. This function will be called by IMA when
IMA detects that the metadata inode is different from the file's inode.
Co-developed-by: Mimi Zohar <[email protected]>
Signed-off-by: Stefan Berger <[email protected]>
Signed-off-by: Mimi Zohar <[email protected]>
|
|
Move all the variables used for file change detection into a structure
that can be used by IMA and EVM. Implement an inline function for storing
the identification of an inode and one for detecting changes to an inode
based on this new structure.
Co-developed-by: Mimi Zohar <[email protected]>
Signed-off-by: Stefan Berger <[email protected]>
Signed-off-by: Mimi Zohar <[email protected]>
|
|
Copying up xattrs is solely based on the security xattr name. For finer
granularity add a dentry parameter to the security_inode_copy_up_xattr
hook definition, allowing decisions to be based on the xattr content as
well.
Co-developed-by: Mimi Zohar <[email protected]>
Signed-off-by: Stefan Berger <[email protected]>
Acked-by: Amir Goldstein <[email protected]>
Acked-by: Paul Moore <[email protected]> (LSM,SELinux)
Signed-off-by: Mimi Zohar <[email protected]>
|
|
The 'r' key is near to 't' key, that makes 'with' to be 'wirh' ? :)
Signed-off-by: Haiyue Wang <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jens Axboe <[email protected]>
|
|
Support atomics in bpf_arena that can be JITed as a single x86 instruction.
Instructions that are JITed as loops are not supported at the moment,
since they require more complex extable and loop logic.
JITs can choose to do smarter things with bpf_jit_supports_insn().
Like arm64 may decide to support all bpf atomics instructions
when emit_lse_atomic is available and none in ll_sc mode.
bpf_jit_supports_percpu_insn(), bpf_jit_supports_ptr_xchg() and
other such callbacks can be replaced with bpf_jit_supports_insn()
in the future.
Signed-off-by: Alexei Starovoitov <[email protected]>
Acked-by: Eduard Zingerman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Martin KaFai Lau <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs into read_iter
* 'work.iov_iter' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
new helper: copy_to_iter_full()
|
|
Add a missing doublequote in the __is_constexpr() macro comment.
Signed-off-by: Thorsten Blum <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
The clk_input_pin attribute of davinci_mcbsp_dev struct is not set since
commit 257ade78b601 ("ASoC: davinci-i2s: Convert to use edma-pcm").
Remove the attribute.
Keep the behaviour of the MCBSP_CLKR case as MCBSP_CLKR == 0.
I can't test the BC_FP format so I added back the initial comment that
was removed by commit ec6375533748 ("ASoC: DaVinci: Added selection of
clk input pin for McBSP"). This was the last dependency to
linux/platform_data/davinci_asp.h so it is not included anymore.
Remove the enum mcbsp_clk_input_pin from davinci_asp.h as it is not used
anywhere else.
Signed-off-by: Bastien Curutchet <[email protected]>
Acked-by: Peter Ujfalusi <[email protected]>
Link: https://msgid.link/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
In some cases, it's useful to be able to select a random cpu from the
intersection of two masks, excluding a particular CPU.
For example, in some systems an uncore PMU is shared by a subset of
CPUs, and management of this PMU is assigned to some arbitrary CPU in
this set. Whenever the management CPU is hotplugged out, we wish to
migrate responsibility to another arbitrary CPU which is both in this
set and online.
Today we can use cpumask_any_and() to select an arbitrary CPU in the
intersection of two masks. We can also use cpumask_any_but() to select
any arbitrary cpu in a mask excluding, a particular CPU.
To do both, we either need to use a temporary cpumask, which is
wasteful, or use some lower-level cpumask helpers, which can be unclear.
This patch adds a new cpumask_any_and_but() to cater for these cases.
Signed-off-by: Mark Rutland <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Cc: Andrew Morton <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Rusty Russell <[email protected]>
Cc: [email protected]
Signed-off-by: Dawei Li <[email protected]>
Acked-by: Yury Norov <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Will Deacon <[email protected]>
|
|
It turns out that while the QSEECOM APP_SEND command has specific fields
for request and response buffers, uefisecapp expects them both to be in
a single memory region. Failure to adhere to this has (so far) resulted
in either no response being written to the response buffer (causing an
EIO to be emitted down the line), the SCM call to fail with EINVAL
(i.e., directly from TZ/firmware), or the device to be hard-reset.
While this issue can be triggered deterministically, in the current form
it seems to happen rather sporadically (which is why it has gone
unnoticed during earlier testing). This is likely due to the two
kzalloc() calls (for request and response) being directly after each
other. Which means that those likely return consecutive regions most of
the time, especially when not much else is going on in the system.
Fix this by allocating a single memory region for both request and
response buffers, properly aligning both structs inside it. This
unfortunately also means that the qcom_scm_qseecom_app_send() interface
needs to be restructured, as it should no longer map the DMA regions
separately. Therefore, move the responsibility of DMA allocation (or
mapping) to the caller.
Fixes: 759e7a2b62eb ("firmware: Add support for Qualcomm UEFI Secure Application")
Cc: [email protected] # 6.7
Tested-by: Johan Hovold <[email protected]>
Reviewed-by: Johan Hovold <[email protected]>
Signed-off-by: Maximilian Luz <[email protected]>
Tested-by: Konrad Dybcio <[email protected]> # X13s
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Bjorn Andersson <[email protected]>
|
|
If the "bootconfig" kernel command-line argument was specified or if
the kernel was built with CONFIG_BOOT_CONFIG_FORCE, but if there are
no embedded kernel parameter, omit the "# Parameters from bootloader:"
comment from the /proc/bootconfig file. This will cause automation
to fall back to the /proc/cmdline file, which will be identical to the
comment in this no-embedded-kernel-parameters case.
Link: https://lore.kernel.org/all/[email protected]/
Fixes: 8b8ce6c75430 ("fs/proc: remove redundant comments from /proc/bootconfig")
Signed-off-by: Masami Hiramatsu <[email protected]>
Signed-off-by: Paul E. McKenney <[email protected]>
Cc: [email protected]
Acked-by: Masami Hiramatsu (Google) <[email protected]>
Signed-off-by: Masami Hiramatsu (Google) <[email protected]>
|
|
PCIe r6.1, sec 6.30.1.1 defines a "DOE Discovery Version" field in
the DOE Discovery Request Data Object Contents (3rd DW) as:
15:8 DOE Discovery Version – must be 02h if the Capability Version in
the Data Object Exchange Extended Capability is 02h or greater.
Add support for the version on devices with the DOE v2 capability.
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Alexey Kardashevskiy <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
Reviewed-by: Kuppuswamy Sathyanarayanan <[email protected]>
|
|
There is no user of the struct plat_max3100 outside the driver.
Inline its contents into the driver. While at it, drop outdated
example in the comment.
Signed-off-by: Andy Shevchenko <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Driver subsystems may need to translate the preferred console name to the
character device name used. We already do some of this in console_setup()
with a few hardcoded names, but that does not scale well.
The console options are parsed early in console_setup(), and the consoles
are added with __add_preferred_console(). At this point we don't know much
about the character device names and device drivers getting probed.
To allow driver subsystems to set up a preferred console, let's save the
kernel command line console options. To add a preferred console from a
driver subsystem with optional character device name translation, let's
add a new function add_preferred_console_match().
This allows the serial core layer to support console=DEVNAME:0.0 style
hardware based addressing in addition to the current console=ttyS0 style
naming. And we can start moving console_setup() character device parsing
to the driver subsystem specific code.
We use a separate array from the console_cmdline array as the character
device name and index may be unknown at the console_setup() time. And
eventually there's no need to call __add_preferred_console() until the
subsystem is ready to handle the console.
Adding the console name in addition to the character device name, and a
flag for an added console, could be added to the struct console_cmdline.
And the console_cmdline array handling could be modified accordingly. But
that complicates things compared saving the console options, and then
adding the consoles when the subsystems handling the consoles are ready.
Co-developed-by: Andy Shevchenko <[email protected]>
Signed-off-by: Tony Lindgren <[email protected]>
Signed-off-by: Andy Shevchenko <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Switch from struct circ_buf to proper kfifo. kfifo provides much better
API, esp. when wrap-around of the buffer needs to be taken into account.
Look at pl011_dma_tx_refill() or cpm_uart_tx_pump() changes for example.
Kfifo API can also fill in scatter-gather DMA structures, so it easier
for that use case too. Look at lpuart_dma_tx() for example. Note that
not all drivers can be converted to that (like atmel_serial), they
handle DMA specially.
Note that usb-serial uses kfifo for TX for ages.
omap needed a bit more care as it needs to put a char into FIFO to start
the DMA transfer when OMAP_DMA_TX_KICK is set. In that case, we have to
do kfifo_dma_out_prepare twice: once to find out the tx_size (to find
out if it is worths to do DMA at all -- size >= 4), the second time for
the actual transfer.
All traces of circ_buf are removed from serial_core.h (and its struct
uart_state).
Signed-off-by: Jiri Slaby (SUSE) <[email protected]>
Cc: Al Cooper <[email protected]>
Cc: Matthias Brugger <[email protected]>
Cc: AngeloGioacchino Del Regno <[email protected]>
Cc: Kumaravel Thiagarajan <[email protected]>
Cc: Tharun Kumar P <[email protected]>
Cc: Russell King <[email protected]>
Cc: Vineet Gupta <[email protected]>
Cc: Richard Genoud <[email protected]>
Cc: Nicolas Ferre <[email protected]>
Cc: Alexandre Belloni <[email protected]>
Cc: Claudiu Beznea <[email protected]>
Cc: Alexander Shiyan <[email protected]>
Cc: Baruch Siach <[email protected]>
Cc: Maciej W. Rozycki <[email protected]>
Cc: Shawn Guo <[email protected]>
Cc: Sascha Hauer <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Neil Armstrong <[email protected]>
Cc: Kevin Hilman <[email protected]>
Cc: Jerome Brunet <[email protected]>
Cc: Martin Blumenstingl <[email protected]>
Cc: Taichi Sugaya <[email protected]>
Cc: Takao Orito <[email protected]>
Cc: Bjorn Andersson <[email protected]>
Cc: Konrad Dybcio <[email protected]>
Cc: Pali Rohár <[email protected]>
Cc: Michael Ellerman <[email protected]>
Cc: Nicholas Piggin <[email protected]>
Cc: Christophe Leroy <[email protected]>
Cc: Aneesh Kumar K.V <[email protected]>
Cc: Naveen N. Rao <[email protected]>
Cc: Manivannan Sadhasivam <[email protected]>
Cc: Krzysztof Kozlowski <[email protected]>
Cc: Alim Akhtar <[email protected]>
Cc: Laxman Dewangan <[email protected]>
Cc: Thierry Reding <[email protected]>
Cc: Jonathan Hunter <[email protected]>
Cc: Orson Zhai <[email protected]>
Cc: Baolin Wang <[email protected]>
Cc: Chunyan Zhang <[email protected]>
Cc: Patrice Chotard <[email protected]>
Cc: Maxime Coquelin <[email protected]>
Cc: Alexandre Torgue <[email protected]>
Cc: David S. Miller <[email protected]>
Cc: Hammer Hsieh <[email protected]>
Cc: Peter Korsgaard <[email protected]>
Cc: Timur Tabi <[email protected]>
Cc: Michal Simek <[email protected]>
Cc: Sumit Semwal <[email protected]>
Cc: Christian König <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Obviously:
"This macro finish" -> "This macro finishes"
and similar.
Signed-off-by: Jiri Slaby (SUSE) <[email protected]>
Cc: Stefani Seibold <[email protected]>
Cc: Andrew Morton <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
When the kfifo buffer is already dma-mapped, one cannot use the kfifo
API to fill in an SG list.
Add kfifo_dma_in_prepare_mapped() which allows exactly this. A mapped
dma_addr_t is passed and it is filled into provided sgl too. Including
the dma_len.
Signed-off-by: Jiri Slaby (SUSE) <[email protected]>
Cc: Stefani Seibold <[email protected]>
Cc: Andrew Morton <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
These are helpers which are going to be used in the serial layer. We
need a wrapper around kfifo which provides us with a tail (sometimes
"tail" offset, sometimes a pointer) to the kfifo data. And which returns
count of available data -- but not larger than to the end of the buffer
(hence _linear in the names). I.e. something like CIRC_CNT_TO_END() in
the legacy circ_buf.
This patch adds such two helpers.
Signed-off-by: Jiri Slaby (SUSE) <[email protected]>
Cc: Stefani Seibold <[email protected]>
Cc: Andrew Morton <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
kfifo_skip_count() is an extended version of kfifo_skip(), accepting
also count. This will be useful in the serial code later.
Now, it can be used to implement both kfifo_skip() and
kfifo_dma_out_finish(). In the latter, 'len' only needs to be divided by
'type' size (as it was until now).
And stop using statement expressions when the return value is cast to
'void'. Use classic 'do {} while (0)' instead.
Note: perhaps we should skip 'count' records for the 'recsize' case, but
the original (kfifo_dma_out_finish()) used to skip only one record. So
this is kept unchanged and 'count' is still ignored in the recsize case.
Signed-off-by: Jiri Slaby (SUSE) <[email protected]>
Cc: Stefani Seibold <[email protected]>
Cc: Andrew Morton <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
It is the same as __kfifo_skip_r(), so:
* drop __kfifo_dma_out_finish_r() completely, and
* replace its (only) use by __kfifo_skip_r().
Signed-off-by: Jiri Slaby (SUSE) <[email protected]>
Cc: Stefani Seibold <[email protected]>
Cc: Andrew Morton <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Currently, all waits for grace periods sleep at TASK_UNINTERRUPTIBLE,
regardless of RCU flavor. This has worked well, but there have been
cases where a longer-than-average Tasks RCU grace period has triggered
softlockup splats, many of them, before the Tasks RCU CPU stall warning
appears. These softlockup splats unnecessarily consume console bandwidth
and complicate diagnosis of the underlying problem. Plus a long but not
pathologically long Tasks RCU grace period might trigger a few softlockup
splats before completing normally, which generates noise for no good
reason.
This commit therefore causes Tasks RCU grace periods to sleep at TASK_IDLE
priority. If there really is a persistent problem, the eventual Tasks
RCU CPU stall warning will flag it, and without the extra noise.
Reported-by: Breno Leitao <[email protected]>
Signed-off-by: Paul E. McKenney <[email protected]>
Signed-off-by: Uladzislau Rezki (Sony) <[email protected]>
|
|
TCP can transform a TIMEWAIT socket into a SYN_RECV one from
a SYN packet, and the ISN of the SYNACK packet is normally
generated using TIMEWAIT tw_snd_nxt :
tcp_timewait_state_process()
...
u32 isn = tcptw->tw_snd_nxt + 65535 + 2;
if (isn == 0)
isn++;
TCP_SKB_CB(skb)->tcp_tw_isn = isn;
return TCP_TW_SYN;
This SYN packet also bypasses normal checks against listen queue
being full or not.
tcp_conn_request()
...
__u32 isn = TCP_SKB_CB(skb)->tcp_tw_isn;
...
/* TW buckets are converted to open requests without
* limitations, they conserve resources and peer is
* evidently real one.
*/
if ((syncookies == 2 || inet_csk_reqsk_queue_is_full(sk)) && !isn) {
want_cookie = tcp_syn_flood_action(sk, rsk_ops->slab_name);
if (!want_cookie)
goto drop;
}
This was using TCP_SKB_CB(skb)->tcp_tw_isn field in skb.
Unfortunately this field has been accidentally cleared
after the call to tcp_timewait_state_process() returning
TCP_TW_SYN.
Using a field in TCP_SKB_CB(skb) for a temporary state
is overkill.
Switch instead to a per-cpu variable.
As a bonus, we do not have to clear tcp_tw_isn in TCP receive
fast path.
It is temporarily set then cleared only in the TCP_TW_SYN dance.
Fixes: 4ad19de8774e ("net: tcp6: fix double call of tcp_v6_fill_cb()")
Fixes: eeea10b83a13 ("tcp: add tcp_v4_fill_cb()/tcp_v4_restore_cb()")
Signed-off-by: Eric Dumazet <[email protected]>
Signed-off-by: Paolo Abeni <[email protected]>
|
|
tcp_v6_init_req() reads TCP_SKB_CB(skb)->tcp_tw_isn to find
out if the request socket is created by a SYN hitting a TIMEWAIT socket.
This has been buggy for a decade, lets directly pass the information
from tcp_conn_request().
This is a preparatory patch to make the following one easier to review.
Signed-off-by: Eric Dumazet <[email protected]>
Signed-off-by: Paolo Abeni <[email protected]>
|
|
Instead of checking for specific file_operations, add a bit to
file_operations which denotes a file that only contain hugetlb pages.
This lets us make hugetlbfs_file_operations static, and removes
is_file_shm_hugepages() completely.
Signed-off-by: Matthew Wilcox (Oracle) <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Christian Brauner <[email protected]>
|
|
Signed-off-by: Ingo Molnar <[email protected]>
|
|
As these addresses can be useful outside of checking if an address
is a multicast address (for example in device drivers) make them
accessible to users of etherdevice.h to avoid code duplication.
Signed-off-by: Diogo Ivo <[email protected]>
Reviewed-by: MD Danish Anwar <[email protected]>
Signed-off-by: Paolo Abeni <[email protected]>
|
|
Signed-off-by: Ingo Molnar <[email protected]>
|
|
Add support for DSCP configuration. For DSCP, get dscp-prio mapping
via hns3 nic driver api .get_dscp_prio() and fill the SL (in WQE for
UD or in QPC for RC) with the priority value. The prio-tc mapping is
configured to HW by hns3 nic driver. HW will select a corresponding
TC according to SL and the prio-tc mapping.
Signed-off-by: Junxian Huang <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Leon Romanovsky <[email protected]>
|
|
After the conversion of dv timing calls to use a pad argument is done,
remove the old callbacks. Update the subdev ioctl handlers to use the
new callbacks.
Signed-off-by: Paweł Anikiel <[email protected]>
Signed-off-by: Hans Verkuil <[email protected]>
|
|
Currently, subdev dv timing calls (i.e. g/s/query_dv_timings) are video
ops without a pad argument. This is a problem if the subdevice can have
different dv timings for each pad (e.g. a DisplayPort receiver with
multiple virtual channels).
To solve this, change these calls to include a pad argument, and put
them into pad ops. Keep the old ones temporarily to make the switch
easier.
Signed-off-by: Paweł Anikiel <[email protected]>
Signed-off-by: Hans Verkuil <[email protected]>
|
|
UBSAN reports this problem:
UBSAN: Undefined behaviour in drivers/md/md.c:8175:15
signed integer overflow:
-2147483291 - 2072033152 cannot be represented in type 'int'
Call trace:
dump_backtrace+0x0/0x310
show_stack+0x28/0x38
dump_stack+0xec/0x15c
ubsan_epilogue+0x18/0x84
handle_overflow+0x14c/0x19c
__ubsan_handle_sub_overflow+0x34/0x44
is_mddev_idle+0x338/0x3d8
md_do_sync+0x1bb8/0x1cf8
md_thread+0x220/0x288
kthread+0x1d8/0x1e0
ret_from_fork+0x10/0x18
'curr_events' will overflow when stat accum or 'sync_io' is greater than
INT_MAX.
Fix it by changing sync_io, last_events and curr_events to 64bit.
Signed-off-by: Li Nan <[email protected]>
Reviewed-by: Yu Kuai <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Song Liu <[email protected]>
|
|
Randy Dunlap <[email protected]> says:
Clean up some SCSI doc files and fix kernel-doc in 6 header files in
include/scsi/.
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
Add a struct short description and a function return value to prevent
kernel-doc warnings:
scsi_transport_srp.h:77: warning: missing initial short description on line:
* struct srp_function_template
scsi_transport_srp.h:132: warning: No description found for return value of 'srp_chkready'
Signed-off-by: Randy Dunlap <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Reviewed-by: Bart Van Assche <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
Add function return value to prevent a kernel-doc warning:
scsi_transport_fc.h:780: warning: No description found for return value of 'fc_remote_port_chkready'
Signed-off-by: Randy Dunlap <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
Add missing function return values to prevent kernel-doc warnings:
scsi.h:75: warning: No description found for return value of 'scsi_status_is_check_condition'
scsi.h:202: warning: No description found for return value of 'scsi_status_is_good'
Signed-off-by: Randy Dunlap <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Reviewed-by: Bart Van Assche <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
Fix all kernel-doc warnings in <scsi/libfcoe.h>:
libfcoe.h:163: warning: Function parameter or struct member 'ctlr' not described in 'fcoe_ctlr_priv'
libfcoe.h:163: warning: Excess function parameter 'cltr' description in 'fcoe_ctlr_priv'
libfcoe.h:163: warning: No description found for return value of 'fcoe_ctlr_priv'
libfcoe.h:218: warning: Function parameter or struct member 'fd_flags' not described in 'fcoe_fcf'
libfcoe.h:218: warning: Excess struct member 'event' description in 'fcoe_fcf'
libfcoe.h:240: warning: Function parameter or struct member 'rdata' not described in 'fcoe_rport'
libfcoe.h:273: warning: No description found for return value of 'is_fip_mode'
libfcoe.h:332: warning: Function parameter or struct member 'crc_eof_page' not described in 'fcoe_percpu_s'
libfcoe.h:332: warning: Function parameter or struct member 'lock' not described in 'fcoe_percpu_s'
libfcoe.h:332: warning: Excess struct member 'page' description in 'fcoe_percpu_s'
libfcoe.h:362: warning: Function parameter or struct member 'data_src_addr' not described in 'fcoe_port'
libfcoe.h:362: warning: Function parameter or struct member 'get_netdev' not described in 'fcoe_port'
libfcoe.h:362: warning: Excess struct member 'data_srt_addr' description in 'fcoe_port'
libfcoe.h:369: warning: No description found for return value of 'fcoe_get_netdev'
libfcoe.h:386: warning: missing initial short description on line:
* struct netdev_list
libfcoe.h:393: warning: expecting prototype for struct netdev_list. Prototype was for struct fcoe_netdev_mapping instead
Signed-off-by: Randy Dunlap <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
Correct kernel-doc comments for struct iser_ctrl to prevent warnings:
iser.h:76: warning: Function parameter or struct member 'read_stag' not described in 'iser_ctrl'
iser.h:76: warning: Excess struct member 'reaf_stag' description in 'iser_ctrl'
Signed-off-by: Randy Dunlap <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Acked-by: Sagi Grimberg <[email protected]>
Reviewed-by: Max Gurtovoy <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
Add entries for missing documentation to prevent kernel-doc warnings:
scsi_cmnd.h:365: warning: Function parameter or struct member 'cmd' not described in 'scsi_msg_to_host_byte'
scsi_cmnd.h:365: warning: Function parameter or struct member 'msg' not described in 'scsi_msg_to_host_byte'
Signed-off-by: Randy Dunlap <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Reviewed-by: Bart Van Assche <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
|