| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This patch adds functionality to configure routes for RPL source routing
functionality. There is no IPIP functionality yet implemented which can
be added later when the cases when to use IPv6 encapuslation comes more
clear.
Signed-off-by: Alexander Aring <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The build_state callback of lwtunnel doesn't contain the net namespace
structure yet. This patch will add it so we can check on specific
address configuration at creation time of rpl source routes.
Signed-off-by: Alexander Aring <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This patch adds rpl source routing receive handling. Everything works
only if sysconf "rpl_seg_enabled" and source routing is enabled. Mostly
the same behaviour as IPv6 segmentation routing. To handle compression
and uncompression a rpl.c file is created which contains the necessary
functionality. The receive handling will also care about IPv6
encapsulated so far it's specified as possible nexthdr in RFC 6554.
Signed-off-by: Alexander Aring <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This patch adds a functionality to addrconf to check on a specific RPL
address configuration. According to RFC 6554:
To detect loops in the SRH, a router MUST determine if the SRH
includes multiple addresses assigned to any interface on that
router. If such addresses appear more than once and are separated by
at least one address not assigned to that router.
Signed-off-by: Alexander Aring <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This patch adds a uapi header for rpl struct definition. The segments
data can be accessed over rpl_segaddr or rpl_segdata macros. In case of
compri and compre is zero the segment data is not compressed and can be
accessed by rpl_segaddr. In the other case the compressed data can be
accessed by rpl_segdata and interpreted as byte array.
Signed-off-by: Alexander Aring <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Expose a new netlink family to userspace to control the PM, setting:
- list of local addresses to be signalled.
- list of local addresses used to created subflows.
- maximum number of add_addr option to react
When the msk is fully established, the PM netlink attempts to
announce the 'signal' list via the ADD_ADDR option. Since we
currently lack the ADD_ADDR echo (and related event) only the
first addr is sent.
After exhausting the 'announce' list, the PM tries to create
subflow for each addr in 'local' list, waiting for each
connection to be completed before attempting the next one.
Idea is to add an additional PM hook for ADD_ADDR echo, to allow
the PM netlink announcing multiple addresses, in sequence.
Co-developed-by: Matthieu Baerts <[email protected]>
Signed-off-by: Matthieu Baerts <[email protected]>
Signed-off-by: Paolo Abeni <[email protected]>
Signed-off-by: Mat Martineau <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Exported via same /proc file as the Linux TCP MIB counters, so "netstat -s"
or "nstat" will show them automatically.
The MPTCP MIB counters are allocated in a distinct pcpu area in order to
avoid bloating/wasting TCP pcpu memory.
Counters are allocated once the first MPTCP socket is created in a
network namespace and free'd on exit.
If no sockets have been allocated, all-zero mptcp counters are shown.
The MIB counter list is taken from the multipath-tcp.org kernel, but
only a few counters have been picked up so far. The counter list can
be increased at any time later on.
v2 -> v3:
- remove 'inline' in foo.c files (David S. Miller)
Co-developed-by: Paolo Abeni <[email protected]>
Signed-off-by: Paolo Abeni <[email protected]>
Signed-off-by: Florian Westphal <[email protected]>
Signed-off-by: Mat Martineau <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
add ulp-specific diagnostic functions, so that subflow information can be
dumped to userspace programs like 'ss'.
v2 -> v3:
- uapi: use bit macros appropriate for userspace
Co-developed-by: Matthieu Baerts <[email protected]>
Signed-off-by: Matthieu Baerts <[email protected]>
Co-developed-by: Paolo Abeni <[email protected]>
Signed-off-by: Paolo Abeni <[email protected]>
Signed-off-by: Davide Caratti <[email protected]>
Signed-off-by: Mat Martineau <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Subflow creation may be initiated by the path manager when
the primary connection is fully established and a remote
address has been received via ADD_ADDR.
Create an in-kernel sock and use kernel_connect() to
initiate connection.
Passive sockets can't acquire the mptcp socket lock at
subflow creation time, so an additional list protected by
a new spinlock is used to track the MPJ subflows.
Such list is spliced into conn_list tail every time the msk
socket lock is acquired, so that it will not interfere
with data flow on the original connection.
Data flow and connection failover not addressed by this commit.
Co-developed-by: Florian Westphal <[email protected]>
Signed-off-by: Florian Westphal <[email protected]>
Co-developed-by: Paolo Abeni <[email protected]>
Signed-off-by: Paolo Abeni <[email protected]>
Co-developed-by: Matthieu Baerts <[email protected]>
Signed-off-by: Matthieu Baerts <[email protected]>
Signed-off-by: Peter Krystad <[email protected]>
Signed-off-by: Mat Martineau <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Process the MP_JOIN option in a SYN packet with the same flow
as MP_CAPABLE but when the third ACK is received add the
subflow to the MPTCP socket subflow list instead of adding it to
the TCP socket accept queue.
The subflow is added at the end of the subflow list so it will not
interfere with the existing subflows operation and no data is
expected to be transmitted on it.
Co-developed-by: Florian Westphal <[email protected]>
Signed-off-by: Florian Westphal <[email protected]>
Co-developed-by: Paolo Abeni <[email protected]>
Signed-off-by: Paolo Abeni <[email protected]>
Signed-off-by: Peter Krystad <[email protected]>
Signed-off-by: Mat Martineau <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Add handling for sending and receiving the ADD_ADDR, ADD_ADDR6,
and RM_ADDR suboptions.
Co-developed-by: Matthieu Baerts <[email protected]>
Signed-off-by: Matthieu Baerts <[email protected]>
Co-developed-by: Paolo Abeni <[email protected]>
Signed-off-by: Paolo Abeni <[email protected]>
Signed-off-by: Peter Krystad <[email protected]>
Signed-off-by: Mat Martineau <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The SKB_SGO_CB_OFFSET should be SKB_GSO_CB_OFFSET which means the
offset of the GSO in skb cb. This patch fixes the typo.
Fixes: 9207f9d45b0a ("net: preserve IP control block during GSO segmentation")
Signed-off-by: Cambda Zhu <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This patch adds new netlink attribute to allow a user to (optionally)
specify the desired offload mode immediately upon MACSec link creation.
Separate iproute patch will be required to support this from user space.
Signed-off-by: Mark Starovoytov <[email protected]>
Signed-off-by: Igor Russkikh <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Minor comment conflict in mac80211.
Signed-off-by: David S. Miller <[email protected]>
|
|
Merge vm fixes from Andrew Morton:
"5 fixes"
* emailed patches from Andrew Morton <[email protected]>:
mm/sparse: fix kernel crash with pfn_section_valid check
mm: fork: fix kernel_stack memcg stats for various stack implementations
hugetlb_cgroup: fix illegal access to memory
drivers/base/memory.c: indicate all memory blocks as removable
mm/swapfile.c: move inode_lock out of claim_swapfile
|
|
Depending on CONFIG_VMAP_STACK and the THREAD_SIZE / PAGE_SIZE ratio the
space for task stacks can be allocated using __vmalloc_node_range(),
alloc_pages_node() and kmem_cache_alloc_node().
In the first and the second cases page->mem_cgroup pointer is set, but
in the third it's not: memcg membership of a slab page should be
determined using the memcg_from_slab_page() function, which looks at
page->slab_cache->memcg_params.memcg . In this case, using
mod_memcg_page_state() (as in account_kernel_stack()) is incorrect:
page->mem_cgroup pointer is NULL even for pages charged to a non-root
memory cgroup.
It can lead to kernel_stack per-memcg counters permanently showing 0 on
some architectures (depending on the configuration).
In order to fix it, let's introduce a mod_memcg_obj_state() helper,
which takes a pointer to a kernel object as a first argument, uses
mem_cgroup_from_obj() to get a RCU-protected memcg pointer and calls
mod_memcg_state(). It allows to handle all possible configurations
(CONFIG_VMAP_STACK and various THREAD_SIZE/PAGE_SIZE values) without
spilling any memcg/kmem specifics into fork.c .
Note: This is a special version of the patch created for stable
backports. It contains code from the following two patches:
- mm: memcg/slab: introduce mem_cgroup_from_obj()
- mm: fork: fix kernel_stack memcg stats for various stack implementations
[[email protected]: introduce mem_cgroup_from_obj()]
Link: http://lkml.kernel.org/r/[email protected]
Fixes: 4d96ba353075 ("mm: memcg/slab: stop setting page->mem_cgroup pointer for slab pages")
Signed-off-by: Roman Gushchin <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Reviewed-by: Shakeel Butt <[email protected]>
Acked-by: Johannes Weiner <[email protected]>
Cc: Michal Hocko <[email protected]>
Cc: Bharata B Rao <[email protected]>
Cc: Shakeel Butt <[email protected]>
Cc: <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Pull networking fixes from David Miller:
1) Fix memory leak in vti6, from Torsten Hilbrich.
2) Fix double free in xfrm_policy_timer, from YueHaibing.
3) NL80211_ATTR_CHANNEL_WIDTH attribute is put with wrong type, from
Johannes Berg.
4) Wrong allocation failure check in qlcnic driver, from Xu Wang.
5) Get ks8851-ml IO operations right, for real this time, from Marek
Vasut.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (22 commits)
r8169: fix PHY driver check on platforms w/o module softdeps
net: ks8851-ml: Fix IO operations, again
mlxsw: spectrum_mr: Fix list iteration in error path
qlcnic: Fix bad kzalloc null test
mac80211: set IEEE80211_TX_CTRL_PORT_CTRL_PROTO for nl80211 TX
mac80211: mark station unauthorized before key removal
mac80211: Check port authorization in the ieee80211_tx_dequeue() case
cfg80211: Do not warn on same channel at the end of CSA
mac80211: drop data frames without key on encrypted links
ieee80211: fix HE SPR size calculation
nl80211: fix NL80211_ATTR_CHANNEL_WIDTH attribute type
xfrm: policy: Fix doulbe free in xfrm_policy_timer
bpf: Explicitly memset some bpf info structures declared on the stack
bpf: Explicitly memset the bpf_attr structure
bpf: Sanitize the bpf_struct_ops tcp-cc name
vti6: Fix memory leak of skb if input policy check fails
esp: remove the skb from the chain when it's enqueued in cryptd_wq
ipv6: xfrm6_tunnel.c: Use built-in RCU list checking
xfrm: add the missing verify_sec_ctx_len check in xfrm_add_acquire
xfrm: fix uctx len check in verify_sec_ctx_len
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Three more driver bugfixes, and two doc improvements fixing build
warnings while we are here"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: pca-platform: Use platform_irq_get_optional
i2c: st: fix missing struct parameter description
i2c: nvidia-gpu: Handle timeout correctly in gpu_i2c_check_status()
i2c: fix a doc warning
i2c: hix5hd2: add missed clk_disable_unprepare in remove
|
|
Daniel Borkmann says:
====================
pull-request: bpf 2020-03-27
The following pull-request contains BPF updates for your *net* tree.
We've added 3 non-merge commits during the last 4 day(s) which contain
a total of 4 files changed, 25 insertions(+), 20 deletions(-).
The main changes are:
1) Explicitly memset the bpf_attr structure on bpf() syscall to avoid
having to rely on compiler to do so. Issues have been noticed on
some compilers with padding and other oddities where the request was
then unexpectedly rejected, from Greg Kroah-Hartman.
2) Sanitize the bpf_struct_ops TCP congestion control name in order to
avoid problematic characters such as whitespaces, from Martin KaFai Lau.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
Changing the MTU for this switch means altering the
DEV_GMII:MAC_CFG_STATUS:MAC_MAXLEN_CFG field MAX_LEN, which in turn
limits the size of frames that can be received.
Special accounting needs to be done for the DSA CPU port (NPI port in
hardware terms). The NPI port configuration needs to be held inside the
private ocelot structure, since it is now accessed from multiple places.
Signed-off-by: Vladimir Oltean <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Many switches don't have an explicit knob for configuring the MTU
(maximum transmission unit per interface). Instead, they do the
length-based packet admission checks on the ingress interface, for
reasons that are easy to understand (why would you accept a packet in
the queuing subsystem if you know you're going to drop it anyway).
So it is actually the MRU that these switches permit configuring.
In Linux there only exists the IFLA_MTU netlink attribute and the
associated dev_set_mtu function. The comments like to play blind and say
that it's changing the "maximum transfer unit", which is to say that
there isn't any directionality in the meaning of the MTU word. So that
is the interpretation that this patch is giving to things: MTU == MRU.
When 2 interfaces having different MTUs are bridged, the bridge driver
MTU auto-adjustment logic kicks in: what br_mtu_auto_adjust() does is it
adjusts the MTU of the bridge net device itself (and not that of the
slave net devices) to the minimum value of all slave interfaces, in
order for forwarded packets to not exceed the MTU regardless of the
interface they are received and send on.
The idea behind this behavior, and why the slave MTUs are not adjusted,
is that normal termination from Linux over the L2 forwarding domain
should happen over the bridge net device, which _is_ properly limited by
the minimum MTU. And termination over individual slave devices is
possible even if those are bridged. But that is not "forwarding", so
there's no reason to do normalization there, since only a single
interface sees that packet.
The problem with those switches that can only control the MRU is with
the offloaded data path, where a packet received on an interface with
MRU 9000 would still be forwarded to an interface with MRU 1500. And the
br_mtu_auto_adjust() function does not really help, since the MTU
configured on the bridge net device is ignored.
In order to enforce the de-facto MTU == MRU rule for these switches, we
need to do MTU normalization, which means: in order for no packet larger
than the MTU configured on this port to be sent, then we need to limit
the MRU on all ports that this packet could possibly come from. AKA
since we are configuring the MRU via MTU, it means that all ports within
a bridge forwarding domain should have the same MTU.
And that is exactly what this patch is trying to do.
>From an implementation perspective, we try to follow the intent of the
user, otherwise there is a risk that we might livelock them (they try to
change the MTU on an already-bridged interface, but we just keep
changing it back in an attempt to keep the MTU normalized). So the MTU
that the bridge is normalized to is either:
- The most recently changed one:
ip link set dev swp0 master br0
ip link set dev swp1 master br0
ip link set dev swp0 mtu 1400
This sequence will make swp1 inherit MTU 1400 from swp0.
- The one of the most recently added interface to the bridge:
ip link set dev swp0 master br0
ip link set dev swp1 mtu 1400
ip link set dev swp1 master br0
The above sequence will make swp0 inherit MTU 1400 as well.
Suggested-by: Florian Fainelli <[email protected]>
Signed-off-by: Vladimir Oltean <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
It is useful be able to configure port policers on a switch to accept
frames of various sizes:
- Increase the MTU for better throughput from the default of 1500 if it
is known that there is no 10/100 Mbps device in the network.
- Decrease the MTU to limit the latency of high-priority frames under
congestion, or work around various network segments that add extra
headers to packets which can't be fragmented.
For DSA slave ports, this is mostly a pass-through callback, called
through the regular ndo ops and at probe time (to ensure consistency
across all supported switches).
The CPU port is called with an MTU equal to the largest configured MTU
of the slave ports. The assumption is that the user might want to
sustain a bidirectional conversation with a partner over any switch
port.
The DSA master is configured the same as the CPU port, plus the tagger
overhead. Since the MTU is by definition L2 payload (sans Ethernet
header), it is up to each individual driver to figure out if it needs to
do anything special for its frame tags on the CPU port (it shouldn't
except in special cases). So the MTU does not contain the tagger
overhead on the CPU port.
However the MTU of the DSA master, minus the tagger overhead, is used as
a proxy for the MTU of the CPU port, which does not have a net device.
This is to avoid uselessly calling the .change_mtu function on the CPU
port when nothing should change.
So it is safe to assume that the DSA master and the CPU port MTUs are
apart by exactly the tagger's overhead in bytes.
Some changes were made around dsa_master_set_mtu(), function which was
now removed, for 2 reasons:
- dev_set_mtu() already calls dev_validate_mtu(), so it's redundant to
do the same thing in DSA
- __dev_set_mtu() returns 0 if ops->ndo_change_mtu is an absent method
That is to say, there's no need for this function in DSA, we can safely
call dev_set_mtu() directly, take the rtnl lock when necessary, and just
propagate whatever errors get reported (since the user probably wants to
be informed).
Some inspiration (mainly in the MTU DSA notifier) was taken from a
vaguely similar patch from Murali and Florian, who are credited as
co-developers down below.
Co-developed-by: Murali Krishna Policharla <[email protected]>
Signed-off-by: Murali Krishna Policharla <[email protected]>
Co-developed-by: Florian Fainelli <[email protected]>
Signed-off-by: Florian Fainelli <[email protected]>
Signed-off-by: Vladimir Oltean <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The BCM7XX PHY family requires special configuration to pass jumbo
frames. Do that during initial PHY setup.
Signed-off-by: Murali Krishna Policharla <[email protected]>
Reviewed-by: Scott Branden <[email protected]>
Signed-off-by: Vladimir Oltean <[email protected]>
Acked-by: Florian Fainelli <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This patch adds a new macro for serial number keyword.
Acked-by: Bjorn Helgaas <[email protected]>
Signed-off-by: Vasundhara Volam <[email protected]>
Signed-off-by: Michael Chan <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Add definition and documentation for the new generic info
"fw.mgmt.api". This macro specifies the version of the software
interfaces between driver and firmware.
Cc: Jakub Kicinski <[email protected]>
Cc: Jacob Keller <[email protected]>
Cc: Jiri Pirko <[email protected]>
Signed-off-by: Vasundhara Volam <[email protected]>
Signed-off-by: Michael Chan <[email protected]>
Reviewed-by: Jiri Pirko <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"A handful of clk driver fixes.
Mostly they're around the i.MX drivers fixing the parents of a few
clks and making KASAN happy with how the message passing code works.
Besides that we have a TI driver fix for the RTC parent and a fix for
the basic gate type registration functions introduced this release
where they didn't actually pass the arguments in the right places to
the multiplexer function down below"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: imx: Align imx sc clock parent msg structs to 4
clk: imx: Align imx sc clock msg structs to 4
clk: Pass correct arguments to __clk_hw_register_gate()
clk: ti: am43xx: Fix clock parent for RTC clock
clk: imx8mp: Correct the enet_qos parent clock
clk: imx8mp: Correct IMX8MP_CLK_HDMI_AXI clock parent
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
- a fix to generate proper timestamps on key autorepeat events that
were broken recently
- a fix for Synaptics driver to only activate reduced reporting mode
when explicitly requested
- a new keycode for "selective screenshot" function
- other assorted fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: fix stale timestamp on key autorepeat events
Input: move the new KEY_SELECTIVE_SCREENSHOT keycode
Input: avoid BIT() macro usage in the serio.h UAPI header
Input: synaptics-rmi4 - set reduced reporting mode only when requested
Input: synaptics - enable RMI on HP Envy 13-ad105ng
Input: allocate keycode for "Selective Screenshot" key
Input: tm2-touchkey - add support for Coreriver TC360 variant
dt-bindings: input: add Coreriver TC360 binding
dt-bindings: vendor-prefixes: Add Coreriver vendor prefix
Input: raydium_i2c_ts - fix error codes in raydium_i2c_boot_trigger()
|
|
When HW offloading is enabled, offloaded stats should be used, because
s/w stats are wrong and out of sync with the HW in this case.
Signed-off-by: Dmitry Bogdanov <[email protected]>
Signed-off-by: Mark Starovoytov <[email protected]>
Signed-off-by: Igor Russkikh <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This patch adds a new MACsec offloading option, MACSEC_OFFLOAD_MAC,
allowing a user to select a MAC as a provider for MACsec offloading
operations.
Signed-off-by: Antoine Tenart <[email protected]>
Signed-off-by: Mark Starovoytov <[email protected]>
Signed-off-by: Igor Russkikh <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This patch allows to reference a net_device from a MACsec context. This
is needed to allow implementing MACsec operations in net device drivers.
Signed-off-by: Antoine Tenart <[email protected]>
Signed-off-by: Mark Starovoytov <[email protected]>
Signed-off-by: Igor Russkikh <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This patch adds a reference to MACsec ops to the net_device structure,
allowing net device drivers to implement offloading operations for
MACsec.
Signed-off-by: Antoine Tenart <[email protected]>
Signed-off-by: Mark Starovoytov <[email protected]>
Signed-off-by: Igor Russkikh <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This patch introduce a new netdev feature, which will be used by drivers
to state they can perform MACsec transformations in hardware.
The patchset was gathered by Mark, macsec functinality itself
was implemented by Dmitry, Mark and Pavel Belous.
Signed-off-by: Antoine Tenart <[email protected]>
Signed-off-by: Mark Starovoytov <[email protected]>
Signed-off-by: Igor Russkikh <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
BIT() macro definition is internal to the Linux kernel and is not
to be used in UAPI headers; replace its usage with the _BITUL() macro
that is already used elsewhere in the header.
Fixes: 9c66d1564676 ("taprio: Add support for hardware offloading")
Signed-off-by: Eugene Syromiatnikov <[email protected]>
Acked-by: Vladimir Oltean <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This is trivial since we already have support for the entirely
identical (from the kernel's point of view) RDNSS, DNSSL, etc. that
also contain opaque data that needs to be passed down to userspace
for further processing.
As specified in draft-ietf-6man-ra-pref64-09 (while it is still a draft,
it is purely waiting on the RFC Editor for cleanups and publishing):
PREF64 option contains lifetime and a (up to) 96-bit IPv6 prefix.
The 8-bit identifier of the option type as assigned by the IANA is 38.
Since we lack DNS64/NAT64/CLAT support in kernel at the moment,
thus this option should also be passed on to userland.
See:
https://tools.ietf.org/html/draft-ietf-6man-ra-pref64-09
https://www.iana.org/assignments/icmpv6-parameters/icmpv6-parameters.xhtml#icmpv6-parameters-5
Cc: Erik Kline <[email protected]>
Cc: Jen Linkova <[email protected]>
Cc: Lorenzo Colitti <[email protected]>
Cc: Michael Haro <[email protected]>
Signed-off-by: Maciej Żenczykowski <[email protected]>
Acked-By: Lorenzo Colitti <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Add an error message when device wasn't found.
While there, also set the bad attribute's offset in extack.
Signed-off-by: Guillaume Nault <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Implement support for the DEVLINK_CMD_REGION_NEW command for creating
snapshots. This new command parallels the existing
DEVLINK_CMD_REGION_DEL.
In order for DEVLINK_CMD_REGION_NEW to work for a region, the new
".snapshot" operation must be implemented in the region's ops structure.
The desired snapshot id must be provided. This helps avoid confusion on
the purpose of DEVLINK_CMD_REGION_NEW, and keeps the API simpler.
The requested id will be inserted into the xarray tracking the number of
snapshots using each id. If this id is already used by another snapshot
on any region, an error will be returned.
Signed-off-by: Jacob Keller <[email protected]>
Reviewed-by: Jiri Pirko <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Each snapshot created for a devlink region must have an id. These ids
are supposed to be unique per "event" that caused the snapshot to be
created. Drivers call devlink_region_snapshot_id_get to obtain a new id
to use for a new event trigger. The id values are tracked per devlink,
so that the same id number can be used if a triggering event creates
multiple snapshots on different regions.
There is no mechanism for snapshot ids to ever be reused. Introduce an
xarray to store the count of how many snapshots are using a given id,
replacing the snapshot_id field previously used for picking the next id.
The devlink_region_snapshot_id_get() function will use xa_alloc to
insert an initial value of 1 value at an available slot between 0 and
U32_MAX.
The new __devlink_snapshot_id_increment() and
__devlink_snapshot_id_decrement() functions will be used to track how
many snapshots currently use an id.
Drivers must now call devlink_snapshot_id_put() in order to release
their reference of the snapshot id after adding region snapshots.
By tracking the total number of snapshots using a given id, it is
possible for the decrement() function to erase the id from the xarray
when it is not in use.
With this method, a snapshot id can become reused again once all
snapshots that referred to it have been deleted via
DEVLINK_CMD_REGION_DEL, and the driver has finished adding snapshots.
This work also paves the way to introduce a mechanism for userspace to
request a snapshot.
Signed-off-by: Jacob Keller <[email protected]>
Reviewed-by: Jiri Pirko <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The devlink_snapshot_id_get() function returns a snapshot id. The
snapshot id is a u32, so there is no way to indicate an error code.
A future change is going to possibly add additional cases where this
function could fail. Refactor the function to return the snapshot id in
an argument, so that it can return zero or an error value.
This ensures that snapshot ids cannot be confused with error values, and
aids in the future refactor of snapshot id allocation management.
Because there is no current way to release previously used snapshot ids,
add a simple check ensuring that an error is reported in case the
snapshot_id would over flow.
Signed-off-by: Jacob Keller <[email protected]>
Reviewed-by: Jiri Pirko <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
It does not makes sense that two snapshots for a given region would use
different destructors. Simplify snapshot creation by adding
a .destructor op for regions.
This operation will replace the data_destructor for the snapshot
creation, and makes snapshot creation easier.
Noticed-by: Jakub Kicinski <[email protected]>
Signed-off-by: Jacob Keller <[email protected]>
Reviewed-by: Jiri Pirko <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Modify the devlink region code in preparation for adding new operations
on regions.
Create a devlink_region_ops structure, and move the name pointer from
within the devlink_region structure into the ops structure (similar to
the devlink_health_reporter_ops).
This prepares the regions to enable support of additional operations in
the future such as requesting snapshots, or accessing the region
directly without a snapshot.
In order to re-use the constant strings in the mlx4 driver their
declaration must be changed to 'const char * const' to ensure the
compiler realizes that both the data and the pointer cannot change.
Signed-off-by: Jacob Keller <[email protected]>
Reviewed-by: Jakub Kicinski <[email protected]>
Reviewed-by: Jiri Pirko <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Pull ceph fixes from Ilya Dryomov:
"A patch for a rather old regression in fullness handling and two
memory leak fixes, marked for stable"
* tag 'ceph-for-5.6-rc8' of git://github.com/ceph/ceph-client:
ceph: fix memory leak in ceph_cleanup_snapid_map()
libceph: fix alloc_msg_with_page_vector() memory leaks
ceph: check POOL_FLAG_FULL/NEARFULL in addition to OSDMAP_FULL/NEARFULL
|
|
We should try to keep keycodes sequential unless there is a reason to leave
a gap in numbering, so let's move it from 0x280 to 0x27a while we still
can.
Fixes: 3b059da9835c ("Input: allocate keycode for Selective Screenshot key")
Acked-by: Rajat Jain <[email protected]>
Link: https://lore.kernel.org/r/20200326182711.GA259753@dtor-ws
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
We have the following fixes:
* drop data packets if there's no key for them anymore, after
there had been one, to avoid sending them in clear when
hostapd removes the key before it removes the station and
the packets are still queued
* check port authorization again after dequeue, to avoid
sending packets if the station is no longer authorized
* actually remove the authorization flag before the key so
packets are also dropped properly because of this
* fix nl80211 control port packet tagging to handle them as
packets allowed to go out without encryption
* fix NL80211_ATTR_CHANNEL_WIDTH outgoing netlink attribute
width (should be 32 bits, not 8)
* don't WARN in a CSA scenario that happens on some APs
* fix HE spatial reuse element size calculation
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
This field references FLOW_ACTION_PACKET_EDIT. Such action does not exist
though. Instead the field is used for FLOW_ACTION_MANGLE and _ADD.
Signed-off-by: Petr Machata <[email protected]>
Reviewed-by: Jiri Pirko <[email protected]>
Signed-off-by: Ido Schimmel <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Overlapping header include additions in macsec.c
A bug fix in 'net' overlapping with the removal of 'version'
string in ena_netdev.c
Overlapping test additions in selftests Makefile
Overlapping PCI ID table adjustments in iwlwifi driver.
Signed-off-by: David S. Miller <[email protected]>
|
|
I copy/pasted these macros and forgot to update the argument
names and where they're passed to. Fix it so that these macros make
sense.
Reported-by: Maxime Ripard <[email protected]>
Fixes: 194efb6e2667 ("clk: gate: Add support for specifying parents via DT/pointers")
Signed-off-by: Stephen Boyd <[email protected]>
Link: https://lkml.kernel.org/r/[email protected]
Tested-by: Maxime Ripard <[email protected]>
|
|
Pull networking fixes from David Miller:
1) Fix deadlock in bpf_send_signal() from Yonghong Song.
2) Fix off by one in kTLS offload of mlx5, from Tariq Toukan.
3) Add missing locking in iwlwifi mvm code, from Avraham Stern.
4) Fix MSG_WAITALL handling in rxrpc, from David Howells.
5) Need to hold RTNL mutex in tcindex_partial_destroy_work(), from Cong
Wang.
6) Fix producer race condition in AF_PACKET, from Willem de Bruijn.
7) cls_route removes the wrong filter during change operations, from
Cong Wang.
8) Reject unrecognized request flags in ethtool netlink code, from
Michal Kubecek.
9) Need to keep MAC in reset until PHY is up in bcmgenet driver, from
Doug Berger.
10) Don't leak ct zone template in act_ct during replace, from Paul
Blakey.
11) Fix flushing of offloaded netfilter flowtable flows, also from Paul
Blakey.
12) Fix throughput drop during tx backpressure in cxgb4, from Rahul
Lakkireddy.
13) Don't let a non-NULL skb->dev leave the TCP stack, from Eric
Dumazet.
14) TCP_QUEUE_SEQ socket option has to update tp->copied_seq as well,
also from Eric Dumazet.
15) Restrict macsec to ethernet devices, from Willem de Bruijn.
16) Fix reference leak in some ethtool *_SET handlers, from Michal
Kubecek.
17) Fix accidental disabling of MSI for some r8169 chips, from Heiner
Kallweit.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (138 commits)
net: Fix CONFIG_NET_CLS_ACT=n and CONFIG_NFT_FWD_NETDEV={y, m} build
net: ena: Add PCI shutdown handler to allow safe kexec
selftests/net/forwarding: define libs as TEST_PROGS_EXTENDED
selftests/net: add missing tests to Makefile
r8169: re-enable MSI on RTL8168c
net: phy: mdio-bcm-unimac: Fix clock handling
cxgb4/ptp: pass the sign of offset delta in FW CMD
net: dsa: tag_8021q: replace dsa_8021q_remove_header with __skb_vlan_pop
net: cbs: Fix software cbs to consider packet sending time
net/mlx5e: Do not recover from a non-fatal syndrome
net/mlx5e: Fix ICOSQ recovery flow with Striding RQ
net/mlx5e: Fix missing reset of SW metadata in Striding RQ reset
net/mlx5e: Enhance ICOSQ WQE info fields
net/mlx5_core: Set IB capability mask1 to fix ib_srpt connection failure
selftests: netfilter: add nfqueue test case
netfilter: nft_fwd_netdev: allow to redirect to ifb via ingress
netfilter: nft_fwd_netdev: validate family and chain type
netfilter: nft_set_rbtree: Detect partial overlaps on insertion
netfilter: nft_set_rbtree: Introduce and use nft_rbtree_interval_start()
netfilter: nft_set_pipapo: Separate partial and complete overlap cases on insertion
...
|
|
net/netfilter/nft_fwd_netdev.c: In function ‘nft_fwd_netdev_eval’:
net/netfilter/nft_fwd_netdev.c:32:10: error: ‘struct sk_buff’ has no member named ‘tc_redirected’
pkt->skb->tc_redirected = 1;
^~
net/netfilter/nft_fwd_netdev.c:33:10: error: ‘struct sk_buff’ has no member named ‘tc_from_ingress’
pkt->skb->tc_from_ingress = 1;
^~
To avoid a direct dependency with tc actions from netfilter, wrap the
redirect bits around CONFIG_NET_REDIRECT and move helpers to
include/linux/skbuff.h. Turn on this toggle from the ifb driver, the
only existing client of these bits in the tree.
This patch adds skb_set_redirected() that sets on the redirected bit
on the skbuff, it specifies if the packet was redirect from ingress
and resets the timestamp (timestamp reset was originally missing in the
netfilter bugfix).
Fixes: bcfabee1afd99484 ("netfilter: nft_fwd_netdev: allow to redirect to ifb via ingress")
Reported-by: [email protected]
Reported-by: Geert Uytterhoeven <[email protected]>
Signed-off-by: Pablo Neira Ayuso <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The he_sr_control field is just a u8, so le32_to_cpu()
shouldn't be applied to it; this was evidently copied
from ieee80211_he_oper_size(). Fix it, and also adjust
the type of the local variable.
Fixes: ef11a931bd1c ("mac80211: HE: add Spatial Reuse element parsing support")
Signed-off-by: Johannes Berg <[email protected]>
Link: https://lore.kernel.org/r/20200325090918.dfe483b49e06.Ia53622f23b2610a2ae6ea39a199866196fe946c1@changeid
Signed-off-by: Johannes Berg <[email protected]>
|
|
Not only did this wheel did not need reinventing, but there is also
an issue with it: It doesn't remove the VLAN header in a way that
preserves the L2 payload checksum when that is being provided by the DSA
master hw. It should recalculate checksum both for the push, before
removing the header, and for the pull afterwards. But the current
implementation is quite dizzying, with pulls followed immediately
afterwards by pushes, the memmove is done before the push, etc. This
makes a DSA master with RX checksumming offload to print stack traces
with the infamous 'hw csum failure' message.
So remove the dsa_8021q_remove_header function and replace it with
something that actually works with inet checksumming.
Fixes: d461933638ae ("net: dsa: tag_8021q: Create helper function for removing VLAN header")
Signed-off-by: Vladimir Oltean <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|