| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
NACK'd by x86 maintainer.
Signed-off-by: David S. Miller <[email protected]>
|
|
Add a per-device sysctl to specify the default traffic class to use for
kernel originated IPv6 Neighbour Discovery packets.
Currently this includes:
- Router Solicitation (ICMPv6 type 133)
ndisc_send_rs() -> ndisc_send_skb() -> ip6_nd_hdr()
- Neighbour Solicitation (ICMPv6 type 135)
ndisc_send_ns() -> ndisc_send_skb() -> ip6_nd_hdr()
- Neighbour Advertisement (ICMPv6 type 136)
ndisc_send_na() -> ndisc_send_skb() -> ip6_nd_hdr()
- Redirect (ICMPv6 type 137)
ndisc_send_redirect() -> ndisc_send_skb() -> ip6_nd_hdr()
and if the kernel ever gets around to generating RA's,
it would presumably also include:
- Router Advertisement (ICMPv6 type 134)
(radvd daemon could pick up on the kernel setting and use it)
Interface drivers may examine the Traffic Class value and translate
the DiffServ Code Point into a link-layer appropriate traffic
prioritization scheme. An example of mapping IETF DSCP values to
IEEE 802.11 User Priority values can be found here:
https://tools.ietf.org/html/draft-ietf-tsvwg-ieee-802-11
The expected primary use case is to properly prioritize ND over wifi.
Testing:
jzem22:~# cat /proc/sys/net/ipv6/conf/eth0/ndisc_tclass
0
jzem22:~# echo -1 > /proc/sys/net/ipv6/conf/eth0/ndisc_tclass
-bash: echo: write error: Invalid argument
jzem22:~# echo 256 > /proc/sys/net/ipv6/conf/eth0/ndisc_tclass
-bash: echo: write error: Invalid argument
jzem22:~# echo 0 > /proc/sys/net/ipv6/conf/eth0/ndisc_tclass
jzem22:~# echo 255 > /proc/sys/net/ipv6/conf/eth0/ndisc_tclass
jzem22:~# cat /proc/sys/net/ipv6/conf/eth0/ndisc_tclass
255
jzem22:~# echo 34 > /proc/sys/net/ipv6/conf/eth0/ndisc_tclass
jzem22:~# cat /proc/sys/net/ipv6/conf/eth0/ndisc_tclass
34
jzem22:~# echo $[0xDC] > /proc/sys/net/ipv6/conf/eth0/ndisc_tclass
jzem22:~# tcpdump -v -i eth0 icmp6 and src host jzem22.pgc and dst host fe80::1
tcpdump: listening on eth0, link-type EN10MB (Ethernet), capture size 262144 bytes
IP6 (class 0xdc, hlim 255, next-header ICMPv6 (58) payload length: 24)
jzem22.pgc > fe80::1: [icmp6 sum ok] ICMP6, neighbor advertisement,
length 24, tgt is jzem22.pgc, Flags [solicited]
(based on original change written by Erik Kline, with minor changes)
v2: fix 'suspicious rcu_dereference_check() usage'
by explicitly grabbing the rcu_read_lock.
Cc: Lorenzo Colitti <[email protected]>
Signed-off-by: Erik Kline <[email protected]>
Signed-off-by: Maciej Żenczykowski <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Error injection is sloppy and very ad-hoc. BPF could fill this niche
perfectly with it's kprobe functionality. We could make sure errors are
only triggered in specific call chains that we care about with very
specific situations. Accomplish this with the bpf_override_funciton
helper. This will modify the probe'd callers return value to the
specified value and set the PC to an override function that simply
returns, bypassing the originally probed function. This gives us a nice
clean way to implement systematic error injection for all of our code
paths.
Acked-by: Alexei Starovoitov <[email protected]>
Signed-off-by: Josef Bacik <[email protected]>
Acked-by: Daniel Borkmann <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Tracefs or debugfs were causing hundreds to thousands of PATH records to
be associated with the init_module and finit_module SYSCALL records on a
few modules when the following rule was in place for startup:
-a always,exit -F arch=x86_64 -S init_module -F key=mod-load
Provide a method to ignore these large number of PATH records from
overwhelming the logs if they are not of interest. Introduce a new
filter list "AUDIT_FILTER_FS", with a new field type AUDIT_FSTYPE,
which keys off the filesystem 4-octet hexadecimal magic identifier to
filter specific filesystem PATH records.
An example rule would look like:
-a never,filesystem -F fstype=0x74726163 -F key=ignore_tracefs
-a never,filesystem -F fstype=0x64626720 -F key=ignore_debugfs
Arguably the better way to address this issue is to disable tracefs and
debugfs on boot from production systems.
See: https://github.com/linux-audit/audit-kernel/issues/16
See: https://github.com/linux-audit/audit-userspace/issues/8
Test case: https://github.com/linux-audit/audit-testsuite/issues/42
Signed-off-by: Richard Guy Briggs <[email protected]>
[PM: fixed the whitespace damage in kernel/auditsc.c]
Signed-off-by: Paul Moore <[email protected]>
|
|
Once an NFC target (i.e., a tag) is found, it remains active until
there is a failure reading or writing it (often caused by the target
moving out of range). While the target is active, the NFC adapter
and antenna must remain powered. This wastes power when the target
remains in range but the client application no longer cares whether
it is there or not.
To mitigate this, add a new netlink command that allows userspace
to deactivate an active target. When issued, this command will cause
the NFC subsystem to act as though the target was moved out of range.
Once the command has been executed, the client application can power
off the NFC adapter to reduce power consumption.
Signed-off-by: Mark Greer <[email protected]>
Signed-off-by: Samuel Ortiz <[email protected]>
|
|
The AIS capability was introduced in 4.12, while the interface to
migrate the state was added in 4.13. Unfortunately it is not possible
for userspace to detect the migration capability without creating a flic
kvm device. As in QEMU the cpu model detection runs on the "none"
machine this will result in cpu model issues regarding the "ais"
capability.
To get the "ais" capability properly let's add a new KVM capability that
tells userspace that AIS states can be migrated.
Signed-off-by: Christian Borntraeger <[email protected]>
Reviewed-by: Cornelia Huck <[email protected]>
Reviewed-by: David Hildenbrand <[email protected]>
Acked-by: Halil Pasic <[email protected]>
|
|
The Wacom Pro Pen 3D includes a third barrel switch which is intended to
be particularly useful in applications where one frequency uses pan, zoom,
and rotate to navigate around a scene or model. The pen is compatible with
the MobileStudio Pro, 2nd-gen Intuos Pro, and Cintiq Pro. When the third
button is pressed, these devices set both the HID_DG_BARRELSWITCH and
HID_DG_BARRELSWITCH2 usages since their HID descriptors do not include a
usage specific to the button.
Rather than send both BTN_STYLUS and BTN_STYLUS2 when the third button is
pressed, userspace (libinput) has requested that we detect this condition
and report a newly-defined BTN_STYLUS3 event instead. We could define a
quirk specific to devices compatible with the Pro Pen 3D, but the liklihood
of seeing both barrel switch bits set with other pens/devices is low enough
to not worry about (pens mechanically prevent accidental activation of
multiple switches).
Signed-off-by: Jason Gerecke <[email protected]>
Acked-by: Dmitry Torokhov <[email protected]>
Acked-by: Peter Hutterer <[email protected]>
Acked-by: Benjamin Tissoires <[email protected]>
Signed-off-by: Jiri Kosina <[email protected]>
|
|
Apparmor will be gaining support for security.apparmor labels, and it
would be helpful to include these in EVM validation now so appropriate
signatures can be generated even before full support is merged.
Signed-off-by: Matthew Garrett <[email protected]>
Acked-by: John Johansen <[email protected]>
Signed-off-by: Mimi Zohar <[email protected]>
|
|
v16->17
- Fixed disputed check code: keep them in nsh_push and nsh_pop
but also add them in __ovs_nla_copy_actions
v15->v16
- Add csum recalculation for nsh_push, nsh_pop and set_nsh
pointed out by Pravin
- Move nsh key into the union with ipv4 and ipv6 and add
check for nsh key in match_validate pointed out by Pravin
- Add nsh check in validate_set and __ovs_nla_copy_actions
v14->v15
- Check size in nsh_hdr_from_nlattr
- Fixed four small issues pointed out By Jiri and Eric
v13->v14
- Rename skb_push_nsh to nsh_push per Dave's comment
- Rename skb_pop_nsh to nsh_pop per Dave's comment
v12->v13
- Fix NSH header length check in set_nsh
v11->v12
- Fix missing changes old comments pointed out
- Fix new comments for v11
v10->v11
- Fix the left three disputable comments for v9
but not fixed in v10.
v9->v10
- Change struct ovs_key_nsh to
struct ovs_nsh_key_base base;
__be32 context[NSH_MD1_CONTEXT_SIZE];
- Fix new comments for v9
v8->v9
- Fix build error reported by daily intel build
because nsh module isn't selected by openvswitch
v7->v8
- Rework nested value and mask for OVS_KEY_ATTR_NSH
- Change pop_nsh to adapt to nsh kernel module
- Fix many issues per comments from Jiri Benc
v6->v7
- Remove NSH GSO patches in v6 because Jiri Benc
reworked it as another patch series and they have
been merged.
- Change it to adapt to nsh kernel module added by NSH
GSO patch series
v5->v6
- Fix the rest comments for v4.
- Add NSH GSO support for VxLAN-gpe + NSH and
Eth + NSH.
v4->v5
- Fix many comments by Jiri Benc and Eric Garver
for v4.
v3->v4
- Add new NSH match field ttl
- Update NSH header to the latest format
which will be final format and won't change
per its author's confirmation.
- Fix comments for v3.
v2->v3
- Change OVS_KEY_ATTR_NSH to nested key to handle
length-fixed attributes and length-variable
attriubte more flexibly.
- Remove struct ovs_action_push_nsh completely
- Add code to handle nested attribute for SET_MASKED
- Change PUSH_NSH to use the nested OVS_KEY_ATTR_NSH
to transfer NSH header data.
- Fix comments and coding style issues by Jiri and Eric
v1->v2
- Change encap_nsh and decap_nsh to push_nsh and pop_nsh
- Dynamically allocate struct ovs_action_push_nsh for
length-variable metadata.
OVS master and 2.8 branch has merged NSH userspace
patch series, this patch is to enable NSH support
in kernel data path in order that OVS can support
NSH in compat mode by porting this.
Signed-off-by: Yi Yang <[email protected]>
Acked-by: Jiri Benc <[email protected]>
Acked-by: Eric Garver <[email protected]>
Acked-by: Pravin Shelar <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Add the ability to offload RED qdisc by using ndo_setup_tc.
There are four commands for RED offloading:
* TC_RED_SET: handles set and change.
* TC_RED_DESTROY: handle qdisc destroy.
* TC_RED_STATS: update the qdiscs counters (given as reference)
* TC_RED_XSTAT: returns red xstats.
Whether RED is being offloaded is being determined every time dump action
is being called because parent change of this qdisc could change its
offload state but doesn't require any RED function to be called.
Signed-off-by: Nogah Frankel <[email protected]>
Signed-off-by: Jiri Pirko <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
In LWT tunnels both an input and output route method is defined.
If both of these are executed in the same path then double translation
happens and the effect is not correct.
This patch adds a new attribute that indicates the hook type. Two
values are defined for route output and route output. ILA
translation is only done for the one that is set. The default is
to enable ILA on route output.
Signed-off-by: Tom Herbert <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Allow identifier to be explicitly configured for a mapping.
This can either be one of the identifier types specified in the
ILA draft or a value of ILA_ATYPE_USE_FORMAT which means the
identifier type is inferred from the identifier type field.
If a value other than ILA_ATYPE_USE_FORMAT is set for a
mapping then it is assumed that the identifier type field is
not present in an identifier.
Signed-off-by: Tom Herbert <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Add checksum neutral auto that performs checksum neutral mapping
without using the C-bit. This is enabled by configuration of
a mapping.
The checksum neutral function has been split into
ila_csum_do_neutral_fmt and ila_csum_do_neutral_nofmt. The former
handles the C-bit and includes it in the adjustment value. The latter
just sets the adjustment value on the locator diff only.
Added configuration for checksum neutral map aut in ila_lwt
and ila_xlat.
Signed-off-by: Tom Herbert <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
USB 3.1 added a PTM_STATUS type. Let's add a define for it and
following patches will let usb_get_status() accept the new argument.
Signed-off-by: Felipe Balbi <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Conflicts:
include/linux/compiler-clang.h
include/linux/compiler-gcc.h
include/linux/compiler-intel.h
include/uapi/linux/stddef.h
Signed-off-by: Ingo Molnar <[email protected]>
|
|
Cgroup v2 lacks the device controller, provided by cgroup v1.
This patch adds a new eBPF program type, which in combination
of previously added ability to attach multiple eBPF programs
to a cgroup, will provide a similar functionality, but with some
additional flexibility.
This patch introduces a BPF_PROG_TYPE_CGROUP_DEVICE program type.
A program takes major and minor device numbers, device type
(block/character) and access type (mknod/read/write) as parameters
and returns an integer which defines if the operation should be
allowed or terminated with -EPERM.
Signed-off-by: Roman Gushchin <[email protected]>
Acked-by: Alexei Starovoitov <[email protected]>
Acked-by: Tejun Heo <[email protected]>
Cc: Daniel Borkmann <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2017-11-04
This series includes:
From Huy: dscp to priority mapping for Ethernet packet.
===================================================
First six patches enable differentiated services code point (dscp) to
priority mapping for Ethernet packet. Once this feature is
enabled, the packet is routed to the corresponding priority based on its
dscp. User can combine this feature with priority flow control (pfc)
feature to have priority flow control based on the dscp.
Firmware interface:
Mellanox firmware provides two control knobs for this feature:
QPTS register allow changing the trust state between dscp and
pcp mode. The default is pcp mode. Once in dscp mode, firmware will
route the packet based on its dscp value if the dscp field exists.
QPDPM register allow mapping a specific dscp (0 to 63) to a
specific priority (0 to 7). By default, all the dscps are mapped to
priority zero.
Software interface:
This feature is controlled via application priority TLV. IEEE
specification P802.1Qcd/D2.1 defines priority selector id 5 for
application priority TLV. This APP TLV selector defines DSCP to priority
map. This APP TLV can be sent by the switch or can be set locally using
software such as lldptool. In mlx5 drivers, we add the support for net
dcb's getapp and setapp call back. Mlx5 driver only handles the selector
id 5 application entry (dscp application priority application entry).
If user sends multiple dscp to priority APP TLV entries on the same
dscp, the last sent one will take effect. All the previous sent will be
deleted.
The firmware trust state (in QPTS register) is changed based on the
number of dscp to priority application entries. When the first dscp to
priority application entry is added by the user, the trust state is
changed to dscp. When the last dscp to priority application entry is
deleted by the user, the trust state is changed to pcp.
When the port is in DSCP trust state, the transmit queue is selected
based on the dscp of the skb.
When the port is in DSCP trust state and vport inline mode is not NONE,
firmware requires mlx5 driver to copy the IP header to the
wqe ethernet segment inline header if the skb has it.
This is done by changing the transmit queue sq's min inline mode to L3.
Note that the min inline mode of sqs that belong to other features
such as xdpsq, icosq are not modified.
===================================================
Plus to the dscp series, some small misc changes are include as well:
From Inbar, Ethtool msglvl support and some debug prints in DCBNL logic
From Or Gerlitz, Enlarge the NIC TC offload table size
From Rabie, Initialize destination_flow struct to 0
From Feras, Add inner TTC table to IPoIB flow steering
From Tal, Enable CQE based moderation on TX CQ
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
Extend struct bpf_prog_info to contain information about program
being bound to a device. Since the netdev may get destroyed while
program still exists we need a flag to indicate the program is
loaded for a device, even if the device is gone.
Signed-off-by: Jakub Kicinski <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Reviewed-by: Quentin Monnet <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The fact that we don't know which device the program is going
to be used on is quite limiting in current eBPF infrastructure.
We have to reverse or limit the changes which kernel makes to
the loaded bytecode if we want it to be offloaded to a networking
device. We also have to invent new APIs for debugging and
troubleshooting support.
Make it possible to load programs for a specific netdev. This
helps us to bring the debug information closer to the core
eBPF infrastructure (e.g. we will be able to reuse the verifer
log in device JIT). It allows device JITs to perform translation
on the original bytecode.
__bpf_prog_get() when called to get a reference for an attachment
point will now refuse to give it if program has a device assigned.
Following patches will add a version of that function which passes
the expected netdev in. @type argument in __bpf_prog_get() is
renamed to attach_type to make it clearer that it's only set on
attachment.
All calls to ndo_bpf are protected by rtnl, only verifier callbacks
are not. We need a wait queue to make sure netdev doesn't get
destroyed while verifier is still running and calling its driver.
Signed-off-by: Jakub Kicinski <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Reviewed-by: Quentin Monnet <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Currently, when an application gets netnsid from the kernel (for example as
the result of RTM_GETLINK call on one end of the veth pair), it's not much
useful. There's no reliable way to get to the netns fd from the netnsid, nor
does any kernel API accept netnsid.
Extend the RTM_GETLINK call to also accept netnsid. It will operate on the
netns with the given netnsid in such case. Of course, the calling process
needs to have enough capabilities in the target name space; for now, require
CAP_NET_ADMIN. This can be relaxed in the future.
To signal to the calling process that the kernel understood the new
IFLA_IF_NETNSID attribute in the query, it will include it in the response.
This is needed to detect older kernels, as they will just ignore
IFLA_IF_NETNSID and query in the current name space.
This patch implemetns IFLA_IF_NETNSID only for get and dump. For set
operations, this can be extended later.
Signed-off-by: Jiri Benc <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This patch allows reliable identification of netdevice interfaces connected
to openvswitch bridges. In particular, user space queries the netdev
interfaces belonging to the ports for statistics, up/down state, etc.
Datapath dump needs to provide enough information for the user space to be
able to do that.
Currently, only interface names are returned. This is not sufficient, as
openvswitch allows its ports to be in different name spaces and the
interface name is valid only in its name space. What is needed and generally
used in other netlink APIs, is the pair ifindex+netnsid.
The solution is addition of the ifindex+netnsid pair (or only ifindex if in
the same name space) to vport get/dump operation.
On request side, ideally the ifindex+netnsid pair could be used to
get/set/del the corresponding vport. This is not implemented by this patch
and can be added later if needed.
Signed-off-by: Jiri Benc <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
IEEE specification P802.1Qcd/D2.1 defines priority selector 5.
This APP TLV selector defines DSCP to priority map.
This patch defines such DSCP selector.
Signed-off-by: Huy Nguyen <[email protected]>
Reviewed-by: Parav Pandit <[email protected]>
Reviewed-by: Or Gerlitz <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
|
|
Files removed in 'net-next' had their license header updated
in 'net'. We take the remove from 'net-next'.
Signed-off-by: David S. Miller <[email protected]>
|
|
It's important for the driver to provide a R/W ioctl to ensure that
two competing userspace processes don't race to provide or read each
others data.
This userspace character device will be used to perform SMBIOS calls
from any applications.
It provides an ioctl that will allow passing the WMI calling
interface buffer between userspace and kernel space.
This character device is intended to deprecate the dcdbas kernel module
and the interface that it provides to userspace.
To perform an SMBIOS IOCTL call using the character device userspace will
perform a read() on the the character device. The WMI bus will provide
a u64 variable containing the necessary size of the IOCTL buffer.
The API for interacting with this interface is defined in documentation
as well as the WMI uapi header provides the format of the structures.
Not all userspace requests will be accepted. The dell-smbios filtering
functionality will be used to prevent access to certain tokens and calls.
All whitelisted commands and tokens are now shared out to userspace so
applications don't need to define them in their own headers.
Signed-off-by: Mario Limonciello <[email protected]>
Reviewed-by: Edward O'Callaghan <[email protected]>
Signed-off-by: Darren Hart (VMware) <[email protected]>
|
|
For WMI operations that are only Set or Query readable and writable sysfs
attributes created by WMI vendor drivers or the bus driver makes sense.
For other WMI operations that are run on Method, there needs to be a
way to guarantee to userspace that the results from the method call
belong to the data request to the method call. Sysfs attributes don't
work well in this scenario because two userspace processes may be
competing at reading/writing an attribute and step on each other's
data.
When a WMI vendor driver declares a callback method in the wmi_driver
the WMI bus driver will create a character device that maps to that
function. This callback method will be responsible for filtering
invalid requests and performing the actual call.
That character device will correspond to this path:
/dev/wmi/$driver
Performing read() on this character device will provide the size
of the buffer that the character device needs to perform calls.
This buffer size can be set by vendor drivers through a new symbol
or when MOF parsing is available by the MOF.
Performing ioctl() on this character device will be interpretd
by the WMI bus driver. It will perform sanity tests for size of
data, test them for a valid instance, copy the data from userspace
and pass iton to the vendor driver to further process and run.
This creates an implicit policy that each driver will only be allowed
a single character device. If a module matches multiple GUID's,
the wmi_devices will need to be all handled by the same wmi_driver.
The WMI vendor drivers will be responsible for managing inappropriate
access to this character device and proper locking on data used by
it.
When a WMI vendor driver is unloaded the WMI bus driver will clean
up the character device and any memory allocated for the call.
Signed-off-by: Mario Limonciello <[email protected]>
Reviewed-by: Edward O'Callaghan <[email protected]>
Signed-off-by: Darren Hart (VMware) <[email protected]>
|
|
This patch adds two arm64-specific prctls, to permit userspace to
control its vector length:
* PR_SVE_SET_VL: set the thread's SVE vector length and vector
length inheritance mode.
* PR_SVE_GET_VL: get the same information.
Although these prctls resemble instruction set features in the SVE
architecture, they provide additional control: the vector length
inheritance mode is Linux-specific and nothing to do with the
architecture, and the architecture does not permit EL0 to set its
own vector length directly. Both can be used in portable tools
without requiring the use of SVE instructions.
Signed-off-by: Dave Martin <[email protected]>
Reviewed-by: Catalin Marinas <[email protected]>
Cc: Alex Bennée <[email protected]>
[will: Fixed up prctl constants to avoid clash with PDEATHSIG]
Signed-off-by: Will Deacon <[email protected]>
|
|
This patch defines and implements a new regset NT_ARM_SVE, which
describes a thread's SVE register state. This allows a debugger to
manipulate the SVE state, as well as being included in ELF
coredumps for post-mortem debugging.
Because the regset size and layout are dependent on the thread's
current vector length, it is not possible to define a C struct to
describe the regset contents as is done for existing regsets.
Instead, and for the same reasons, NT_ARM_SVE is based on the
freeform variable-layout approach used for the SVE signal frame.
Additionally, to reduce debug overhead when debugging threads that
might or might not have live SVE register state, NT_ARM_SVE may be
presented in one of two different formats: the old struct
user_fpsimd_state format is embedded for describing the state of a
thread with no live SVE state, whereas a new variable-layout
structure is embedded for describing live SVE state. This avoids a
debugger needing to poll NT_PRFPREG in addition to NT_ARM_SVE, and
allows existing userspace code to handle the non-SVE case without
too much modification.
For this to work, NT_ARM_SVE is defined with a fixed-format header
of type struct user_sve_header, which the recipient can use to
figure out the content, size and layout of the reset of the regset.
Accessor macros are defined to allow the vector-length-dependent
parts of the regset to be manipulated.
Signed-off-by: Alan Hayward <[email protected]>
Signed-off-by: Dave Martin <[email protected]>
Reviewed-by: Catalin Marinas <[email protected]>
Cc: Alex Bennée <[email protected]>
Cc: Okamoto Takayuki <[email protected]>
Signed-off-by: Will Deacon <[email protected]>
|
|
This patch implements the core logic for changing a task's vector
length on request from userspace. This will be used by the ptrace
and prctl frontends that are implemented in later patches.
The SVE architecture permits, but does not require, implementations
to support vector lengths that are not a power of two. To handle
this, logic is added to check a requested vector length against a
possibly sparse bitmap of available vector lengths at runtime, so
that the best supported value can be chosen.
Signed-off-by: Dave Martin <[email protected]>
Reviewed-by: Catalin Marinas <[email protected]>
Cc: Alex Bennée <[email protected]>
Signed-off-by: Will Deacon <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull initial SPDX identifiers from Greg KH:
"License cleanup: add SPDX license identifiers to some files
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the
'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally
binding shorthand, which can be used instead of the full boiler plate
text.
This patch is based on work done by Thomas Gleixner and Kate Stewart
and Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset
of the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to
license had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied
to a file was done in a spreadsheet of side by side results from of
the output of two independent scanners (ScanCode & Windriver)
producing SPDX tag:value files created by Philippe Ombredanne.
Philippe prepared the base worksheet, and did an initial spot review
of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537
files assessed. Kate Stewart did a file by file comparison of the
scanner results in the spreadsheet to determine which SPDX license
identifier(s) to be applied to the file. She confirmed any
determination that was not immediately clear with lawyers working with
the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained
>5 lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that
was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that
became the concluded license(s).
- when there was disagreement between the two scanners (one detected
a license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply
(and which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases,
confirmation by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.
The Windriver scanner is based on an older version of FOSSology in
part, so they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot
checks in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect
the correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial
patch version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch
license was not GPL-2.0 WITH Linux-syscall-note to ensure that the
applied SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <[email protected]>
Reviewed-by: Philippe Ombredanne <[email protected]>
Reviewed-by: Thomas Gleixner <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>"
* tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
License cleanup: add SPDX license identifier to uapi header files with a license
License cleanup: add SPDX license identifier to uapi header files with no license
License cleanup: add SPDX GPL-2.0 license identifier to files with no license
|
|
Many user space API headers have licensing information, which is either
incomplete, badly formatted or just a shorthand for referring to the
license under which the file is supposed to be. This makes it hard for
compliance tools to determine the correct license.
Update these files with an SPDX license identifier. The identifier was
chosen based on the license information in the file.
GPL/LGPL licensed headers get the matching GPL/LGPL SPDX license
identifier with the added 'WITH Linux-syscall-note' exception, which is
the officially assigned exception identifier for the kernel syscall
exception:
NOTE! This copyright does *not* cover user programs that use kernel
services by normal system calls - this is merely considered normal use
of the kernel, and does *not* fall under the heading of "derived work".
This exception makes it possible to include GPL headers into non GPL
code, without confusing license compliance tools.
Headers which have either explicit dual licensing or are just licensed
under a non GPL license are updated with the corresponding SPDX
identifier and the GPLv2 with syscall exception identifier. The format
is:
((GPL-2.0 WITH Linux-syscall-note) OR SPDX-ID-OF-OTHER-LICENSE)
SPDX license identifiers are a legally binding shorthand, which can be
used instead of the full boiler plate text. The update does not remove
existing license information as this has to be done on a case by case
basis and the copyright holders might have to be consulted. This will
happen in a separate step.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne. See the previous patch in this series for the
methodology of how this patch was researched.
Reviewed-by: Kate Stewart <[email protected]>
Reviewed-by: Philippe Ombredanne <[email protected]>
Reviewed-by: Thomas Gleixner <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
license
Many user space API headers are missing licensing information, which
makes it hard for compliance tools to determine the correct license.
By default are files without license information under the default
license of the kernel, which is GPLV2. Marking them GPLV2 would exclude
them from being included in non GPLV2 code, which is obviously not
intended. The user space API headers fall under the syscall exception
which is in the kernels COPYING file:
NOTE! This copyright does *not* cover user programs that use kernel
services by normal system calls - this is merely considered normal use
of the kernel, and does *not* fall under the heading of "derived work".
otherwise syscall usage would not be possible.
Update the files which contain no license information with an SPDX
license identifier. The chosen identifier is 'GPL-2.0 WITH
Linux-syscall-note' which is the officially assigned identifier for the
Linux syscall exception. SPDX license identifiers are a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne. See the previous patch in this series for the
methodology of how this patch was researched.
Reviewed-by: Kate Stewart <[email protected]>
Reviewed-by: Philippe Ombredanne <[email protected]>
Reviewed-by: Thomas Gleixner <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Smooth Cong Wang's bug fix into 'net-next'. Basically put
the bulk of the tcf_block_put() logic from 'net' into
tcf_block_put_ext(), but after the offload unbind.
Signed-off-by: David S. Miller <[email protected]>
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-next
- Fix documentation build issues (Randy, Markus)
- Fix timestamp frequency calculation for perf on CNL (Lionel)
- New DMC firmware for Skylake (Anusha)
- GTT flush fixes and other GGTT write track and refactors (Chris)
- Taint kernel when GPU reset fails (Chris)
- Display workarounds organization (Lucas)
- GuC and HuC initialization clean-up and fixes (Michal)
- Other fixes around GuC submission (Michal)
- Execlist clean-ups like caching ELSP reg offset and improving log readability (Chri\
s)
- Many other improvements on our logs and dumps (Chris)
- Restore GT performance in headless mode with DMC loaded (Tvrtko)
- Stop updating legacy fb parameters since FBC is not using anymore (Daniel)
- More selftest improvements (Chris)
- Preemption fixes and improvements (Chris)
- x86/early-quirks improvements for Intel graphics stolen memory. (Joonas, Matthew)
- Other improvements on Stolen Memory code to be resource centric. (Matthew)
- Improvements and fixes on fence allocation/release (Chris).
GVT:
- fixes for two coverity scan errors (Colin)
- mmio switch code refine (Changbin)
- more virtual display dmabuf fixes (Tina/Gustavo)
- misc cleanups (Pei)
- VFIO mdev display dmabuf interface and gvt support (Tina)
- VFIO mdev opregion support/fixes (Tina/Xiong/Chris)
- workload scheduling optimization (Changbin)
- preemption fix and temporal workaround (Zhenyu)
- and misc fixes after refactor (Chris)
* tag 'drm-intel-next-2017-12-14' of git://anongit.freedesktop.org/drm/drm-intel: (87 commits)
drm/i915: Update DRIVER_DATE to 20171214
drm/i915: properly init lockdep class
drm/i915: Show engine state when hangcheck detects a stall
drm/i915: make CS frequency read support missing more obvious
drm/i915/guc: Extract doorbell verification into a function
drm/i915/guc: Extract clients allocation to submission_init
drm/i915/guc: Extract doorbell creation from client allocation
drm/i915/guc: Call invalidate after changing the vfunc
drm/i915/guc: Extract guc_init from guc_init_hw
drm/i915/guc: Move GuC workqueue allocations outside of the mutex
drm/i915/guc: Move shared data allocation away from submission path
drm/i915: Unwind i915_gem_init() failure
drm/i915: Ratelimit request allocation under oom
drm/i915: Allow fence allocations to fail
drm/i915: Mark up potential allocation paths within i915_sw_fence as might_sleep
drm/i915: Don't check #active_requests from i915_gem_wait_for_idle()
drm/i915/fence: Use rcu to defer freeing of irq_work
drm/i915: Dump the engine state before declaring wedged from wait_for_engines()
drm/i915: Bump timeout for wait_for_engines()
drm/i915: Downgrade misleading "Memory usable" message
...
|
|
Chris requested this backmerge for a reconciliation on
drm_print.h between drm-misc-next and drm-intel-next-queued
Signed-off-by: Rodrigo Vivi <[email protected]>
|
|
Add VFIO_DEVICE_QUERY_GFX_PLANE ioctl command to let user query and get
a plane and its information. So far, two types of buffers are supported:
buffers based on dma-buf and buffers based on region.
This ioctl can be invoked with:
1) Either DMABUF or REGION flag. Vendor driver returns a plane_info
successfully only when the specific kind of buffer is supported.
2) Flag PROBE. And at the same time either DMABUF or REGION must be set,
so that vendor driver returns success only when the specific kind of
buffer is supported.
Add VFIO_DEVICE_GET_GFX_DMABUF ioctl command to let user get a specific
dma-buf fd of an exposed MDEV buffer provided by dmabuf_id which was
returned in VFIO_DEVICE_QUERY_GFX_PLANE ioctl command.
The life cycle of an exposed MDEV buffer is handled by userspace and
tracked by kernel space. The returned dmabuf_id in struct vfio_device_
query_gfx_plane can be a new id of a new exposed buffer or an old id of
a re-exported buffer. Host user can check the value of dmabuf_id to see
if it needs to create new resources according to the new exposed buffer
or just re-use the existing resource related to the old buffer.
v18:
- update comments for VFIO_DEVICE_GET_GFX_DMABUF. (Alex)
v17:
- modify VFIO_DEVICE_GET_GFX_DMABUF interface. (Alex)
v16:
- add x_hot and y_hot fields. (Gerd)
- add comments for VFIO_DEVICE_GET_GFX_DMABUF. (Alex)
- rebase to 4.14.0-rc6.
v15:
- add a ioctl to get a dmabuf for a given dmabuf id. (Gerd)
v14:
- add PROBE, DMABUF and REGION flags. (Alex)
v12:
- add drm_format_mod back. (Gerd and Zhenyu)
- add region_index. (Gerd)
v11:
- rename plane_type to drm_plane_type. (Gerd)
- move fields of vfio_device_query_gfx_plane to vfio_device_gfx_plane_info.
(Gerd)
- remove drm_format_mod, start fields. (Daniel)
- remove plane_id.
v10:
- refine the ABI API VFIO_DEVICE_QUERY_GFX_PLANE. (Alex) (Gerd)
v3:
- add a field gvt_plane_info in the drm_i915_gem_obj structure to save
the decoded plane information to avoid look up while need the plane
info. (Gerd)
Signed-off-by: Tina Zhang <[email protected]>
Reviewed-by: Gerd Hoffmann <[email protected]>
Reviewed-by: Kirti Wankhede <[email protected]>
Acked-by: Alex Williamson <[email protected]>
Cc: Daniel Vetter <[email protected]>
Signed-off-by: Zhenyu Wang <[email protected]>
|
|
Now that check_extent_in_eb()'s extent offset filter can be turned off,
we need a way to do it from userspace.
Add a 'flags' field to the btrfs_logical_ino_args structure to disable
extent offset filtering, taking the place of one of the existing
reserved[] fields.
Previous versions of LOGICAL_INO neglected to check whether any of the
reserved fields have non-zero values. Assigning meaning to those fields
now may change the behavior of existing programs that left these fields
uninitialized. The lack of a zero check also means that new programs
have no way to know whether the kernel is honoring the flags field.
To avoid these problems, define a new ioctl LOGICAL_INO_V2. We can
use the same argument layout as LOGICAL_INO, but shorten the reserved[]
array by one element and turn it into the 'flags' field. The V2 ioctl
explicitly checks that reserved fields and unsupported flag bits are zero
so that userspace can negotiate future feature bits as they are defined.
Since the memory layouts of the two ioctls' arguments are compatible,
there is no need for a separate function for logical_to_ino_v2 (contrast
with tree_search_v2 vs tree_search where the layout and code are quite
different). A version parameter and an 'if' statement will suffice.
Now that we have a flags field in logical_ino_args, add a flag
BTRFS_LOGICAL_INO_ARGS_IGNORE_OFFSET to get the behavior we want,
and pass it down the stack to iterate_inodes_from_logical.
Motivation and background, copied from the patchset cover letter:
Suppose we have a file with one extent:
root@tester:~# zcat /usr/share/doc/cpio/changelog.gz > /test/a
root@tester:~# sync
Split the extent by overwriting it in the middle:
root@tester:~# cat /dev/urandom | dd bs=4k seek=2 skip=2 count=1 conv=notrunc of=/test/a
We should now have 3 extent refs to 2 extents, with one block unreachable.
The extent tree looks like:
root@tester:~# btrfs-debug-tree /dev/vdc -t 2
[...]
item 9 key (1103101952 EXTENT_ITEM 73728) itemoff 15942 itemsize 53
extent refs 2 gen 29 flags DATA
extent data backref root 5 objectid 261 offset 0 count 2
[...]
item 11 key (1103175680 EXTENT_ITEM 4096) itemoff 15865 itemsize 53
extent refs 1 gen 30 flags DATA
extent data backref root 5 objectid 261 offset 8192 count 1
[...]
and the ref tree looks like:
root@tester:~# btrfs-debug-tree /dev/vdc -t 5
[...]
item 6 key (261 EXTENT_DATA 0) itemoff 15825 itemsize 53
extent data disk byte 1103101952 nr 73728
extent data offset 0 nr 8192 ram 73728
extent compression(none)
item 7 key (261 EXTENT_DATA 8192) itemoff 15772 itemsize 53
extent data disk byte 1103175680 nr 4096
extent data offset 0 nr 4096 ram 4096
extent compression(none)
item 8 key (261 EXTENT_DATA 12288) itemoff 15719 itemsize 53
extent data disk byte 1103101952 nr 73728
extent data offset 12288 nr 61440 ram 73728
extent compression(none)
[...]
There are two references to the same extent with different, non-overlapping
byte offsets:
[------------------72K extent at 1103101952----------------------]
[--8K----------------|--4K unreachable----|--60K-----------------]
^ ^
| |
[--8K ref offset 0--][--4K ref offset 0--][--60K ref offset 12K--]
|
v
[-----4K extent-----] at 1103175680
We want to find all of the references to extent bytenr 1103101952.
Without the patch (and without running btrfs-debug-tree), we have to
do it with 18 LOGICAL_INO calls:
root@tester:~# btrfs ins log 1103101952 -P /test/
Using LOGICAL_INO
inode 261 offset 0 root 5
root@tester:~# for x in $(seq 0 17); do btrfs ins log $((1103101952 + x * 4096)) -P /test/; done 2>&1 | grep inode
inode 261 offset 0 root 5
inode 261 offset 4096 root 5 <- same extent ref as offset 0
(offset 8192 returns empty set, not reachable)
inode 261 offset 12288 root 5
inode 261 offset 16384 root 5 \
inode 261 offset 20480 root 5 |
inode 261 offset 24576 root 5 |
inode 261 offset 28672 root 5 |
inode 261 offset 32768 root 5 |
inode 261 offset 36864 root 5 \
inode 261 offset 40960 root 5 > all the same extent ref as offset 12288.
inode 261 offset 45056 root 5 / More processing required in userspace
inode 261 offset 49152 root 5 | to figure out these are all duplicates.
inode 261 offset 53248 root 5 |
inode 261 offset 57344 root 5 |
inode 261 offset 61440 root 5 |
inode 261 offset 65536 root 5 |
inode 261 offset 69632 root 5 /
In the worst case the extents are 128MB long, and we have to do 32768
iterations of the loop to find one 4K extent ref.
With the patch, we just use one call to map all refs to the extent at once:
root@tester:~# btrfs ins log 1103101952 -P /test/
Using LOGICAL_INO_V2
inode 261 offset 0 root 5
inode 261 offset 12288 root 5
The TREE_SEARCH ioctl allows userspace to retrieve the offset and
extent bytenr fields easily once the root, inode and offset are known.
This is sufficient information to build a complete map of the extent
and all of its references. Userspace can use this information to make
better choices to dedup or defrag.
Signed-off-by: Zygo Blaxell <[email protected]>
Reviewed-by: Hans van Kranenburg <[email protected]>
Tested-by: Hans van Kranenburg <[email protected]>
[ copy background and motivation from cover letter ]
Signed-off-by: David Sterba <[email protected]>
|
|
Now that SK_REDIRECT is no longer a valid return code. Remove it
from the UAPI completely. Then do a namespace remapping internal
to sockmap so SK_REDIRECT is no longer externally visible.
Patchs primary change is to do a namechange from SK_REDIRECT to
__SK_REDIRECT
Reported-by: Alexei Starovoitov <[email protected]>
Signed-off-by: John Fastabend <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Based on the discussion about the signed character field for the year,
I went through all fields in the iso9660 and rockridge standards to see
whether they should used signed or unsigned characters. Only a single
8-bit value is defined as signed per 'section 7.1.2': the timezone
offset in a timestamp, this has always been handled correctly through
explicit sign-extension.
All others are either '7.1.1 8-bit unsigned numerical values' or
composite fields. I also read the linux source code and came to the
same conclusion, also I could not find any other part of the
implementation that actually behaves differently for signed or
unsigned values.
Since it is still ambigous to use plain 'char' in interface definitions,
I'm changing all fields representing numbers and reserved bytes to
the unambiguous '__u8'. Fields that hold actual strings are left as
'char' arrays. I built the code with '-Wpointer-sign -Wsign-compare'
to see if anything got left out, but couldn't find anything wrong
with the remaining warnings.
This patch should not change runtime behavior and does not need to
be backported.
Signed-off-by: Arnd Bergmann <[email protected]>
Signed-off-by: Jan Kara <[email protected]>
|
|
Several conflicts here.
NFP driver bug fix adding nfp_netdev_is_nfp_repr() check to
nfp_fl_output() needed some adjustments because the code block is in
an else block now.
Parallel additions to net/pkt_cls.h and net/sch_generic.h
A bug fix in __tcp_retransmit_skb() conflicted with some of
the rbtree changes in net-next.
The tc action RCU callback fixes in 'net' had some overlap with some
of the recent tcf_block reworking.
Signed-off-by: David S. Miller <[email protected]>
|
|
Add extra checks for item with EXTENT_DATA type. This checks the
following thing:
0) Key offset
All key offsets must be aligned to sectorsize.
Inline extent must have 0 for key offset.
1) Item size
Uncompressed inline file extent size must match item size.
(Compressed inline file extent has no information about its on-disk size.)
Regular/preallocated file extent size must be a fixed value.
2) Every member of regular file extent item
Including alignment for bytenr and offset, possible value for
compression/encryption/type.
3) Type/compression/encode must be one of the valid values.
This should be the most comprehensive and strict check in the context
of btrfs_item for EXTENT_DATA.
Signed-off-by: Qu Wenruo <[email protected]>
Reviewed-by: Nikolay Borisov <[email protected]>
Reviewed-by: David Sterba <[email protected]>
[ switch to BTRFS_FILE_EXTENT_TYPES, similar to what
BTRFS_COMPRESS_TYPES does ]
Signed-off-by: David Sterba <[email protected]>
|
|
Pull networking fixes from David Miller:
1) Fix route leak in xfrm_bundle_create().
2) In mac80211, validate user rate mask before configuring it. From
Johannes Berg.
3) Properly enforce memory limits in fair queueing code, from Toke
Hoiland-Jorgensen.
4) Fix lockdep splat in inet_csk_route_req(), from Eric Dumazet.
5) Fix TSO header allocation and management in mvpp2 driver, from Yan
Markman.
6) Don't take socket lock in BH handler in strparser code, from Tom
Herbert.
7) Don't show sockets from other namespaces in AF_UNIX code, from
Andrei Vagin.
8) Fix double free in error path of tap_open(), from Girish Moodalbail.
9) Fix TX map failure path in igb and ixgbe, from Jean-Philippe Brucker
and Alexander Duyck.
10) Fix DCB mode programming in stmmac driver, from Jose Abreu.
11) Fix err_count handling in various tunnels (ipip, ip6_gre). From Xin
Long.
12) Properly align SKB head before building SKB in tuntap, from Jason
Wang.
13) Avoid matching qdiscs with a zero handle during lookups, from Cong
Wang.
14) Fix various endianness bugs in sctp, from Xin Long.
15) Fix tc filter callback races and add selftests which trigger the
problem, from Cong Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (73 commits)
selftests: Introduce a new test case to tc testsuite
selftests: Introduce a new script to generate tc batch file
net_sched: fix call_rcu() race on act_sample module removal
net_sched: add rtnl assertion to tcf_exts_destroy()
net_sched: use tcf_queue_work() in tcindex filter
net_sched: use tcf_queue_work() in rsvp filter
net_sched: use tcf_queue_work() in route filter
net_sched: use tcf_queue_work() in u32 filter
net_sched: use tcf_queue_work() in matchall filter
net_sched: use tcf_queue_work() in fw filter
net_sched: use tcf_queue_work() in flower filter
net_sched: use tcf_queue_work() in flow filter
net_sched: use tcf_queue_work() in cgroup filter
net_sched: use tcf_queue_work() in bpf filter
net_sched: use tcf_queue_work() in basic filter
net_sched: introduce a workqueue for RCU callbacks of tc filter
sctp: fix some type cast warnings introduced since very beginning
sctp: fix a type cast warnings that causes a_rwnd gets the wrong value
sctp: fix some type cast warnings introduced by transport rhashtable
sctp: fix some type cast warnings introduced by stream reconf
...
|
|
This is very similar to the Macvlan VEPA mode, however, there is some
difference. IPvlan uses the mac-address of the lower device, so the VEPA
mode has implications of ICMP-redirects for packets destined for its
immediate neighbors sharing same master since the packets will have same
source and dest mac. The external switch/router will send redirect msg.
Having said that, this will be useful tool in terms of debugging
since IPvlan will not switch packets within its slaves and rely completely
on the external entity as intended in 802.1Qbg.
Signed-off-by: Mahesh Bandewar <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
IPvlan has always operated in bridge mode. However there are scenarios
where each slave should be able to talk through the master device but
not necessarily across each other. Think of an environment where each
of a namespace is a private and independant customer. In this scenario
the machine which is hosting these namespaces neither want to tell who
their neighbor is nor the individual namespaces care to talk to neighbor
on short-circuited network path.
This patch implements the mode that is very similar to the 'private' mode
in macvlan where individual slaves can send and receive traffic through
the master device, just that they can not talk among slave devices.
Signed-off-by: Mahesh Bandewar <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
These warnings were found by running 'make C=2 M=net/sctp/'.
They are there since very beginning.
Note after this patch, there still one warning left in
sctp_outq_flush():
sctp_chunk_fail(chunk, SCTP_ERROR_INV_STRM)
Since it has been moved to sctp_stream_outq_migrate on net-next,
to avoid the extra job when merging net-next to net, I will post
the fix for it after the merging is done.
Reported-by: Eric Dumazet <[email protected]>
Signed-off-by: Xin Long <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Cached routes should only be created by the system when receiving pmtu
discovery or ip redirect msg. Users should not be allowed to create
cached routes.
Furthermore, after the patch series to move cached routes into exception
table, user added cached routes will trigger the following warning in
fib6_add():
WARNING: CPU: 0 PID: 2985 at net/ipv6/ip6_fib.c:1137
fib6_add+0x20d9/0x2c10 net/ipv6/ip6_fib.c:1137
Kernel panic - not syncing: panic_on_warn set ...
CPU: 0 PID: 2985 Comm: syzkaller320388 Not tainted 4.14.0-rc3+ #74
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:16 [inline]
dump_stack+0x194/0x257 lib/dump_stack.c:52
panic+0x1e4/0x417 kernel/panic.c:181
__warn+0x1c4/0x1d9 kernel/panic.c:542
report_bug+0x211/0x2d0 lib/bug.c:183
fixup_bug+0x40/0x90 arch/x86/kernel/traps.c:178
do_trap_no_signal arch/x86/kernel/traps.c:212 [inline]
do_trap+0x260/0x390 arch/x86/kernel/traps.c:261
do_error_trap+0x120/0x390 arch/x86/kernel/traps.c:298
do_invalid_op+0x1b/0x20 arch/x86/kernel/traps.c:311
invalid_op+0x18/0x20 arch/x86/entry/entry_64.S:905
RIP: 0010:fib6_add+0x20d9/0x2c10 net/ipv6/ip6_fib.c:1137
RSP: 0018:ffff8801cf09f6a0 EFLAGS: 00010297
RAX: ffff8801ce45e340 RBX: 1ffff10039e13eec RCX: ffff8801d749c814
RDX: 0000000000000000 RSI: ffff8801d749c700 RDI: ffff8801d749c780
RBP: ffff8801cf09fa08 R08: 0000000000000000 R09: ffff8801cf09f360
R10: ffff8801cf09f2d8 R11: 1ffff10039c8befb R12: 0000000000000001
R13: dffffc0000000000 R14: ffff8801d749c700 R15: ffffffff860655c0
__ip6_ins_rt+0x6c/0x90 net/ipv6/route.c:1011
ip6_route_add+0x148/0x1a0 net/ipv6/route.c:2782
ipv6_route_ioctl+0x4d5/0x690 net/ipv6/route.c:3291
inet6_ioctl+0xef/0x1e0 net/ipv6/af_inet6.c:521
sock_do_ioctl+0x65/0xb0 net/socket.c:961
sock_ioctl+0x2c2/0x440 net/socket.c:1058
vfs_ioctl fs/ioctl.c:45 [inline]
do_vfs_ioctl+0x1b1/0x1530 fs/ioctl.c:685
SYSC_ioctl fs/ioctl.c:700 [inline]
SyS_ioctl+0x8f/0xc0 fs/ioctl.c:691
entry_SYSCALL_64_fastpath+0x1f/0xbe
So we fix this by failing the attemp to add cached routes from userspace
with returning EINVAL error.
Fixes: 2b760fcf5cfb ("ipv6: hook up exception table to store dst cache")
Signed-off-by: Wei Wang <[email protected]>
Signed-off-by: Eric Dumazet <[email protected]>
Acked-by: Martin KaFai Lau <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Recent additions to support multiple programs in cgroups impose
a strict requirement, "all yes is yes, any no is no". To enforce
this the infrastructure requires the 'no' return code, SK_DROP in
this case, to be 0.
To apply these rules to SK_SKB program types the sk_actions return
codes need to be adjusted.
This fix adds SK_PASS and makes 'SK_DROP = 0'. Finally, remove
SK_ABORTED to remove any chance that the API may allow aborted
program flows to be passed up the stack. This would be incorrect
behavior and allow programs to break existing policies.
Signed-off-by: John Fastabend <[email protected]>
Acked-by: Alexei Starovoitov <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Signed-off-by: Oded Gabbay <[email protected]>
Reviewed-by: Ben Goz <[email protected]>
Signed-off-by: Felix Kuehling <[email protected]>
|
|
This queueing discipline implements the shaper algorithm defined by
the 802.1Q-2014 Section 8.6.8.2 and detailed in Annex L.
It's primary usage is to apply some bandwidth reservation to user
defined traffic classes, which are mapped to different queues via the
mqprio qdisc.
Only a simple software implementation is added for now.
Signed-off-by: Vinicius Costa Gomes <[email protected]>
Signed-off-by: Jesus Sanchez-Palencia <[email protected]>
Tested-by: Henrik Austad <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
'spi/fix/qspi', 'spi/fix/stm32' and 'spi/fix/uapi' into spi-linus
|
|
Currently, ip6_tnl_xmit_ctl drops tunneled packets if the remote
address (outer v6 destination) is one of host's locally configured
addresses.
Same applies to ip6_tnl_rcv_ctl: it drops packets if the remote address
(outer v6 source) is a local address.
This prevents using ipxip6 (and ip6_gre) tunnels whose local/remote
endpoints are on same host; OTOH v4 tunnels (ipip or gre) allow such
configurations.
An example where this proves useful is a system where entities are
identified by their unique v6 addresses, and use tunnels to encapsulate
traffic between them. The limitation prevents placing several entities
on same host.
Introduce IP6_TNL_F_ALLOW_LOCAL_REMOTE which allows to bypass this
restriction.
Signed-off-by: Shmulik Ladkani <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|