| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
RFC 4443 added two new codes values for ICMPv6 type 1:
5 - Source address failed ingress/egress policy
6 - Reject route to destination
And RFC 7084 states in L-14 that IPv6 Router MUST send ICMPv6 Destination
Unreachable with code 5 for packets forwarded to it that use an address
from a prefix that has been invalidated.
Codes 5 and 6 are more informative subsets of code 1.
Signed-off-by: Andreas Herz <andi@geekosphere.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
For a userland lock request, the previous and current
lock modes are used to decide when the lvb should be
copied back to the user. The wrong previous value was
used, so that it always matched the current value.
This caused the lvb to be copied back to the user in
the wrong cases.
Signed-off-by: David Teigland <teigland@redhat.com>
|
|
kvm-queue
Patch queue for ppc - 2015-08-22
Highlights for KVM PPC this time around:
- Book3S: A few bug fixes
- Book3S: Allow micro-threading on POWER8
|
|
- mcast_group: configure the multicast address, now IPv6
is supported too
- mcast_port: configure the multicast port
- mcast_ttl: configure the multicast TTL/HOP_LIMIT
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
|
|
Allow setups with large MTU to send large sync packets by
adding sync_maxlen parameter. The default value is now based
on MTU but no more than 1500 for compatibility reasons.
To avoid problems if MTU changes allow fragmentation by
sending packets with DF=0. Problem reported by Dan Carpenter.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
|
|
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
This is second pull request includes the conflict resolution patch that
resulted from the updates that we got for the conntrack template through
kmalloc. No changes with regards to the previously sent 15 patches.
The following patchset contains Netfilter updates for your net-next tree, they
are:
1) Rework the existing nf_tables counter expression to make it per-cpu.
2) Prepare and factor out common packet duplication code from the TEE target so
it can be reused from the new dup expression.
3) Add the new dup expression for the nf_tables IPv4 and IPv6 families.
4) Convert the nf_tables limit expression to use a token-based approach with
64-bits precision.
5) Enhance the nf_tables limit expression to support limiting at packet byte.
This comes after several preparation patches.
6) Add a burst parameter to indicate the amount of packets or bytes that can
exceed the limiting.
7) Add netns support to nfacct, from Andreas Schultz.
8) Pass the nf_conn_zone structure instead of the zone ID in nf_tables to allow
accessing more zone specific information, from Daniel Borkmann.
9) Allow to define zone per-direction to support netns containers with
overlapping network addressing, also from Daniel.
10) Extend the CT target to allow setting the zone based on the skb->mark as a
way to support simple mappings from iptables, also from Daniel.
11) Make the nf_tables payload expression aware of the fact that VLAN offload
may have removed a vlan header, from Florian Westphal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next
Resolve conflicts with conntrack template fixes.
Conflicts:
net/netfilter/nf_conntrack_core.c
net/netfilter/nf_synproxy_core.c
net/netfilter/xt_CT.c
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Allow specification of per route IP tunnel instructions also for IPv6.
This complements commit 3093fbe7ff4b ("route: Per route IP tunnel metadata
via lightweight tunnel").
Signed-off-by: Jiri Benc <jbenc@redhat.com>
CC: YOSHIFUJI Hideaki <hideaki.yoshifuji@miraclelinux.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
more changes
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
If the user selected the precise_timestamps or histogram options, report
it in the @stats_list message output.
If the user didn't select these options, no extra tokens are reported,
thus it is backward compatible with old software that doesn't know about
precise timestamps and histogram.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 4.2
|
|
Controllers can perform optional subsystem resets as introduced in NVMe
1.1. This patch adds an IOCTL to trigger the subsystem reset by writing
"NVMe" to the NSSR register.
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Acked-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Adding new module name ila. This implements ILA translation. Light
weight tunnel redirection is used to perform the translation in
the data path. This is configured by the "ip -6 route" command
using the "encap ila <locator>" option, where <locator> is the
value to set in destination locator of the packet. e.g.
ip -6 route add 3333:0:0:1:5555:0:1:0/128 \
encap ila 2001:0:0:1 via 2401:db00:20:911a:face:0:25:0
Sets a route where 3333:0:0:1 will be overwritten by
2001:0:0:1 on output.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This work adds the possibility of deriving the zone id from the skb->mark
field in a scalable manner. This allows for having only a single template
serving hundreds/thousands of different zones, for example, instead of the
need to have one match for each zone as an extra CT jump target.
Note that we'd need to have this information attached to the template as at
the time when we're trying to lookup a possible ct object, we already need
to know zone information for a possible match when going into
__nf_conntrack_find_get(). This work provides a minimal implementation for
a possible mapping.
In order to not add/expose an extra ct->status bit, the zone structure has
been extended to carry a flag for deriving the mark.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This work adds a direction parameter to netfilter zones, so identity
separation can be performed only in original/reply or both directions
(default). This basically opens up the possibility of doing NAT with
conflicting IP address/port tuples from multiple, isolated tenants
on a host (e.g. from a netns) without requiring each tenant to NAT
twice resp. to use its own dedicated IP address to SNAT to, meaning
overlapping tuples can be made unique with the zone identifier in
original direction, where the NAT engine will then allocate a unique
tuple in the commonly shared default zone for the reply direction.
In some restricted, local DNAT cases, also port redirection could be
used for making the reply traffic unique w/o requiring SNAT.
The consensus we've reached and discussed at NFWS and since the initial
implementation [1] was to directly integrate the direction meta data
into the existing zones infrastructure, as opposed to the ct->mark
approach we proposed initially.
As we pass the nf_conntrack_zone object directly around, we don't have
to touch all call-sites, but only those, that contain equality checks
of zones. Thus, based on the current direction (original or reply),
we either return the actual id, or the default NF_CT_DEFAULT_ZONE_ID.
CT expectations are direction-agnostic entities when expectations are
being compared among themselves, so we can only use the identifier
in this case.
Note that zone identifiers can not be included into the hash mix
anymore as they don't contain a "stable" value that would be equal
for both directions at all times, f.e. if only zone->id would
unconditionally be xor'ed into the table slot hash, then replies won't
find the corresponding conntracking entry anymore.
If no particular direction is specified when configuring zones, the
behaviour is exactly as we expect currently (both directions).
Support has been added for the CT netlink interface as well as the
x_tables raw CT target, which both already offer existing interfaces
to user space for the configuration of zones.
Below a minimal, simplified collision example (script in [2]) with
netperf sessions:
+--- tenant-1 ---+ mark := 1
| netperf |--+
+----------------+ | CT zone := mark [ORIGINAL]
[ip,sport] := X +--------------+ +--- gateway ---+
| mark routing |--| SNAT |-- ... +
+--------------+ +---------------+ |
+--- tenant-2 ---+ | ~~~|~~~
| netperf |--+ +-----------+ |
+----------------+ mark := 2 | netserver |------ ... +
[ip,sport] := X +-----------+
[ip,port] := Y
On the gateway netns, example:
iptables -t raw -A PREROUTING -j CT --zone mark --zone-dir ORIGINAL
iptables -t nat -A POSTROUTING -o <dev> -j SNAT --to-source <ip> --random-fully
iptables -t mangle -A PREROUTING -m conntrack --ctdir ORIGINAL -j CONNMARK --save-mark
iptables -t mangle -A POSTROUTING -m conntrack --ctdir REPLY -j CONNMARK --restore-mark
conntrack dump from gateway netns:
netperf -H 10.1.1.2 -t TCP_STREAM -l60 -p12865,5555 from each tenant netns
tcp 6 431995 ESTABLISHED src=40.1.1.1 dst=10.1.1.2 sport=5555 dport=12865 zone-orig=1
src=10.1.1.2 dst=10.1.1.1 sport=12865 dport=1024
[ASSURED] mark=1 secctx=system_u:object_r:unlabeled_t:s0 use=1
tcp 6 431994 ESTABLISHED src=40.1.1.1 dst=10.1.1.2 sport=5555 dport=12865 zone-orig=2
src=10.1.1.2 dst=10.1.1.1 sport=12865 dport=5555
[ASSURED] mark=2 secctx=system_u:object_r:unlabeled_t:s0 use=1
tcp 6 299 ESTABLISHED src=40.1.1.1 dst=10.1.1.2 sport=39438 dport=33768 zone-orig=1
src=10.1.1.2 dst=10.1.1.1 sport=33768 dport=39438
[ASSURED] mark=1 secctx=system_u:object_r:unlabeled_t:s0 use=1
tcp 6 300 ESTABLISHED src=40.1.1.1 dst=10.1.1.2 sport=32889 dport=40206 zone-orig=2
src=10.1.1.2 dst=10.1.1.1 sport=40206 dport=32889
[ASSURED] mark=2 secctx=system_u:object_r:unlabeled_t:s0 use=2
Taking this further, test script in [2] creates 200 tenants and runs
original-tuple colliding netperf sessions each. A conntrack -L dump in
the gateway netns also confirms 200 overlapping entries, all in ESTABLISHED
state as expected.
I also did run various other tests with some permutations of the script,
to mention some: SNAT in random/random-fully/persistent mode, no zones (no
overlaps), static zones (original, reply, both directions), etc.
[1] http://thread.gmane.org/gmane.comp.security.firewalls.netfilter.devel/57412/
[2] https://paste.fedoraproject.org/242835/65657871/
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Add fanout mode PACKET_FANOUT_EBPF that accepts an en extended BPF
program to select a socket.
Update the internal eBPF program by passing to socket option
SOL_PACKET/PACKET_FANOUT_DATA a file descriptor returned by bpf().
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add fanout mode PACKET_FANOUT_CBPF that accepts a classic BPF program
to select a socket.
This avoids having to keep adding special case fanout modes. One
example use case is application layer load balancing. The QUIC
protocol, for instance, encodes a connection ID in UDP payload.
Also add socket option SOL_PACKET/PACKET_FANOUT_DATA that updates data
associated with the socket group. Fanout mode PACKET_FANOUT_CBPF is the
only user so far.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We already have IFLA_IPTUN_ netlink attributes. The IP_TUN_ attributes look
very similar, yet they serve very different purpose. This is confusing for
anyone trying to implement a user space tool supporting lwt.
As the IP_TUN_ attributes are used only for the lightweight tunnels, prefix
them with LWTUNNEL_IP_ instead to make their purpose clear. Also, it's more
logical to have them in lwtunnel.h together with the encap enum.
Fixes: 3093fbe7ff4b ("route: Per route IP tunnel metadata via lightweight tunnel")
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.3 merge window
New support for Allwinne SoC on the MUSB driver has been added to the list of
glue layers. MUSB also got support for building all DMA engines in one binary;
this will be great for distros.
DWC3 now has no trace of dev_dbg()/dev_vdbg() usage. We will rely solely on
tracing to debug DWC3. There was also a fix for memory corruption with EP0 when
maxpacket size transfers are > 512 bytes.
Robert's EP capabilities flags is making EP selection a lot simpler. UDCs are
now required to set these flags up when adding endpoints to the framework.
Other than these, we have the usual set of miscelaneous cleanups and minor
fixes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Add a VRF_MASTER flag for interfaces and helper functions for determining
if a device is a VRF_MASTER.
Add link attribute for passing VRF_TABLE id.
Add vrf_ptr to netdevice.
Add various macros for determining if a device is a VRF device, the index
of the master VRF device and table associated with VRF device.
Signed-off-by: Shrijeet Mukherjee <shm@cumulusnetworks.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Like the ipv4 patch with a similar title, this adds a sysctl to allow
the user to change routing behavior based on whether or not the
interface associated with the nexthop was an up or down link. The
default setting preserves the current behavior, but anyone that enables
it will notice that nexthops on down interfaces will no longer be
selected:
net.ipv6.conf.all.ignore_routes_with_linkdown = 0
net.ipv6.conf.default.ignore_routes_with_linkdown = 0
net.ipv6.conf.lo.ignore_routes_with_linkdown = 0
...
When the above sysctls are set, not only will link status be reported to
userspace, but an indication that a nexthop is dead and will not be used
is also reported.
1000::/8 via 7000::2 dev p7p1 metric 1024 dead linkdown pref medium
1000::/8 via 8000::2 dev p8p1 metric 1024 pref medium
7000::/8 dev p7p1 proto kernel metric 256 dead linkdown pref medium
8000::/8 dev p8p1 proto kernel metric 256 pref medium
9000::/8 via 8000::2 dev p8p1 metric 2048 pref medium
9000::/8 via 7000::2 dev p7p1 metric 1024 dead linkdown pref medium
fe80::/64 dev p7p1 proto kernel metric 256 dead linkdown pref medium
fe80::/64 dev p8p1 proto kernel metric 256 pref medium
This also adds devconf support and notification when sysctl values
change.
v2: drop use of rt6i_nhflags since it is not needed right now
Signed-off-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: Dinesh Dutt <ddutt@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/ethernet/cavium/Kconfig
The cavium conflict was overlapping dependency
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Following patch create new tunnel flag which enable
tunnel metadata collection on given device.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add an explicit neighbour table overflow message (ratelimited) and
statistic to make diagnosing neighbour table overflows tractable in
the wild.
Diagnosing a neighbour table overflow can be quite difficult in the wild
because there is no explicit dmesg logged. Callers to neighbour code
seem to use net_dbg_ratelimit when the neighbour call fails which means
the "base message" is not emitted and the callback suppressed messages
from the ratelimiting can end-up juxtaposed with unrelated messages.
Further, a forced garbage collection will increment a stat on each call
whether it was successful in freeing-up a table entry or not, so that
statistic is only a hint. So, add a net_info_ratelimited message and
explicit statistic to the neighbour code.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the ability to toggle the vlan filtering support via
netlink. Since we're already running with rtnl in .changelink() we don't
need to take any additional locks.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PMU conuter
According to the perf_event_map_fd and index, the function
bpf_perf_event_read() can convert the corresponding map
value to the pointer to struct perf_event and return the
Hardware PMU counter value.
Signed-off-by: Kaixu Xia <xiakaixu@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce a new bpf map type 'BPF_MAP_TYPE_PERF_EVENT_ARRAY'.
This map only stores the pointer to struct perf_event. The
user space event FDs from perf_event_open() syscall are converted
to the pointer to struct perf_event and stored in map.
Signed-off-by: Kaixu Xia <xiakaixu@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We want the fixes in Linus's tree in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
IFLA_VXLAN_FLOWBASED is useless without IFLA_VXLAN_COLLECT_METADATA,
so combine them into single IFLA_VXLAN_COLLECT_METADATA flag.
'flowbased' doesn't convey real meaning of the vxlan tunnel mode.
This mode can be used by routing, tc+bpf and ovs.
Only ovs is strictly flow based, so 'collect metadata' is a better
name for this tunnel mode.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds a new NFTA_LIMIT_TYPE netlink attribute to indicate the type of
limiting.
Contrary to per-packet limiting, the cost is calculated from the packet path
since this depends on the packet length.
The burst attribute indicates the number of bytes in which the rate can be
exceeded.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This patch adds the burst parameter. This burst indicates the number of packets
that can exceed the limit.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This new expression uses the nf_dup engine to clone packets to a given gateway.
Unlike xt_TEE, we use an index to indicate output interface which should be
fine at this stage.
Moreover, change to the preemtion-safe this_cpu_read(nf_skb_duplicated) from
nf_dup_ipv{4,6} to silence a lockdep splat.
Based on the original tee expression from Arturo Borrero Gonzalez, although
this patch has diverted quite a bit from this initial effort due to the
change to support maps.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This adds the ability audit the actions of a not-yet-running process.
This patch implements the ability to filter on the executable path. Instead of
just hard coding the ino and dev of the executable we care about at the moment
the rule is inserted into the kernel, use the new audit_fsnotify
infrastructure to manage this dynamically. This means that if the filename
does not yet exist but the containing directory does, or if the inode in
question is unlinked and creat'd (aka updated) the rule will just continue to
work. If the containing directory is moved or deleted or the filesystem is
unmounted, the rule is deleted automatically. A future enhancement would be to
have the rule survive across directory disruptions.
This is a heavily modified version of a patch originally submitted by Eric
Paris with some ideas from Peter Moody.
Cc: Peter Moody <peter@hda3.com>
Cc: Eric Paris <eparis@redhat.com>
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
[PM: minor whitespace clean to satisfy ./scripts/checkpatch]
Signed-off-by: Paul Moore <pmoore@redhat.com>
|
|
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for net-next, they are:
1) A couple of cleanups for the netfilter core hook from Eric Biederman.
2) Net namespace hook registration, also from Eric. This adds a dependency with
the rtnl_lock. This should be fine by now but we have to keep an eye on this
because if we ever get the per-subsys nfnl_lock before rtnl we have may
problems in the future. But we have room to remove this in the future by
propagating the complexity to the clients, by registering hooks for the init
netns functions.
3) Update nf_tables to use the new net namespace hook infrastructure, also from
Eric.
4) Three patches to refine and to address problems from the new net namespace
hook infrastructure.
5) Switch to alternate jumpstack in xtables iff the packet is reentering. This
only applies to a very special case, the TEE target, but Eric Dumazet
reports that this is slowing down things for everyone else. So let's only
switch to the alternate jumpstack if the tee target is in used through a
static key. This batch also comes with offline precalculation of the
jumpstack based on the callchain depth. From Florian Westphal.
6) Minimal SCTP multihoming support for our conntrack helper, from Michal
Kubecek.
7) Reduce nf_bridge_info per skbuff scratchpad area to 32 bytes, from Florian
Westphal.
8) Fix several checkpatch errors in bridge netfilter, from Bernhard Thaler.
9) Get rid of useless debug message in ip6t_REJECT, from Subash Abhinov.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fix from Bjorn Helgaas:
"This is a trivial fix for a change that broke user program compilation
(QEMU in this case)"
* tag 'pci-v4.2-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Restore PCI_MSIX_FLAGS_BIRMASK definition
|
|
Intel Skylake supports reporting the time in cycles a branch in the LBR
took, to give a rough indication of the basic block performance.
Export the cycle information in the branch_info structure.
This can be done by just reusing some currently zero padding.
This is just the generic header change. The architecture
still needs to fill it in.
There's no attempt to convert to real time, as we really
want cycles here.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: eranian@google.com
Link: http://lkml.kernel.org/r/1431285767-27027-5-git-send-email-andi@firstfloor.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
In multiple locations there are checks for whether the label in hand
is a reserved label or not using the arbritray value of 16. Factor
this out into a #define for better maintainability and for
documentation.
Signed-off-by: Robert Shearman <rshearma@brocade.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add ioctl IOCTL_MEI_NOTIFY_SET for enabling and disabling
async event notification.
Add ioctl IOCTL_MEI_NOTIFY_GET for receiving and acking
an event notification.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add skb->hash to the __sk_buff offset map, so it can be accessed from
an eBPF program. We currently already do this for classic BPF filters,
but not yet on eBPF, it might be useful as a demuxer in combination with
helpers like bpf_clone_redirect(), toy example:
__section("cls-lb") int ingress_main(struct __sk_buff *skb)
{
unsigned int which = 3 + (skb->hash & 7);
/* bpf_skb_store_bytes(skb, ...); */
/* bpf_l{3,4}_csum_replace(skb, ...); */
bpf_clone_redirect(skb, which, 0);
return -1;
}
I was thinking whether to add skb_get_hash(), but then concluded the
raw skb->hash seems fine in this case: we can directly access the hash
w/o extra eBPF helper function call, it's filled out by many NICs on
ingress, and in case the entropy level would not be sufficient, people
can still implement their own specific sw fallback hash mix anyway.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
arch/s390/net/bpf_jit_comp.c
drivers/net/ethernet/ti/netcp_ethss.c
net/bridge/br_multicast.c
net/ipv4/ip_fragment.c
All four conflicts were cases of simple overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tlb_dynamic_lb could be set only via sysfs, this patch allows it to be
set via netlink.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Two vxlan driver flags FLOWBASED and COLLECT_METADATA need to be set to
make use of its new flow mode. The former already exposed. Expose the latter.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce helpers to let eBPF programs attached to TC manipulate tunnel metadata:
bpf_skb_[gs]et_tunnel_key(skb, key, size, flags)
skb: pointer to skb
key: pointer to 'struct bpf_tunnel_key'
size: size of 'struct bpf_tunnel_key'
flags: room for future extensions
First eBPF program that uses these helpers will allocate per_cpu
metadata_dst structures that will be used on TX.
On RX metadata_dst is allocated by tunnel driver.
Typical usage for TX:
struct bpf_tunnel_key tkey;
... populate tkey ...
bpf_skb_set_tunnel_key(skb, &tkey, sizeof(tkey), 0);
bpf_clone_redirect(skb, vxlan_dev_ifindex, 0);
RX:
struct bpf_tunnel_key tkey = {};
bpf_skb_get_tunnel_key(skb, &tkey, sizeof(tkey), 0);
... lookup or redirect based on tkey ...
'struct bpf_tunnel_key' will be extended in the future by adding
elements to the end and the 'size' argument will indicate which fields
are populated, thereby keeping backwards compatibility.
The 'flags' argument may be used as well when the 'size' is not enough or
to indicate completely different layout of bpf_tunnel_key.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
more changes
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Commit 6fd99094de2b ("ipv6: Don't reduce hop limit for an interface")
disabled accept hop limit from RA if it is smaller than the current hop
limit for security stuff. But this behavior kind of break the RFC definition.
RFC 4861, 6.3.4. Processing Received Router Advertisements
A Router Advertisement field (e.g., Cur Hop Limit, Reachable Time,
and Retrans Timer) may contain a value denoting that it is
unspecified. In such cases, the parameter should be ignored and the
host should continue using whatever value it is already using.
If the received Cur Hop Limit value is non-zero, the host SHOULD set
its CurHopLimit variable to the received value.
So add sysctl option accept_ra_min_hop_limit to let user choose the minimum
hop limit value they can accept from RA. And set default to 1 to meet RFC
standards.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: YOSHIFUJI Hideaki <hideaki.yoshifuji@miraclelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com>
|
|
Currently nf_conntrack_proto_sctp module handles only packets between
primary addresses used to establish the connection. Any packets between
secondary addresses are classified as invalid so that usual firewall
configurations drop them. Allowing HEARTBEAT and HEARTBEAT-ACK chunks to
establish a new conntrack would allow traffic between secondary
addresses to pass through. A more sophisticated solution based on the
addresses advertised in the initial handshake (and possibly also later
dynamic address addition and removal) would be much harder to implement.
Moreover, in general we cannot assume to always see the initial
handshake as it can be routed through a different path.
The patch adds two new conntrack states:
SCTP_CONNTRACK_HEARTBEAT_SENT - a HEARTBEAT chunk seen but not acked
SCTP_CONNTRACK_HEARTBEAT_ACKED - a HEARTBEAT acked by HEARTBEAT-ACK
State transition rules:
- HEARTBEAT_SENT responds to usual chunks the same way as NONE (so that
the behaviour changes as little as possible)
- HEARTBEAT_ACKED responds to usual chunks the same way as ESTABLISHED
does, except the resulting state is HEARTBEAT_ACKED rather than
ESTABLISHED
- previously existing states except NONE are preserved when HEARTBEAT or
HEARTBEAT-ACK is seen
- NONE (in the initial direction) changes to HEARTBEAT_SENT on HEARTBEAT
and to CLOSED on HEARTBEAT-ACK
- HEARTBEAT_SENT changes to HEARTBEAT_ACKED on HEARTBEAT-ACK in the
reply direction
- HEARTBEAT_SENT and HEARTBEAT_ACKED are preserved on HEARTBEAT and
HEARTBEAT-ACK otherwise
Normally, vtag is set from the INIT chunk for the reply direction and
from the INIT-ACK chunk for the originating direction (i.e. each of
these defines vtag value for the opposite direction). For secondary
conntracks, we can't rely on seeing INIT/INIT-ACK and even if we have
seen them, we would need to connect two different conntracks. Therefore
simplified logic is applied: vtag of first packet in each direction
(HEARTBEAT in the originating and HEARTBEAT-ACK in reply direction) is
saved and all following packets in that direction are compared with this
saved value. While INIT and INIT-ACK define vtag for the opposite
direction, vtags extracted from HEARTBEAT and HEARTBEAT-ACK are always
for their direction.
Default timeout values for new states are
HEARTBEAT_SENT: 30 seconds (default hb_interval)
HEARTBEAT_ACKED: 210 seconds (hb_interval * path_max_retry + max_rto)
(We cannot expect to see the shutdown sequence so that, unlike
ESTABLISHED, the HEARTBEAT_ACKED timeout shouldn't be too long.)
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Add USB_OTG_ADP definition for usb_otg_descriptor.bmAttributes.
Signed-off-by: Macpaul Lin <macpaul@gmail.com>
Signed-off-by: Li Jun <jun.li@freescale.com>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
OTG 2.0 introduces bcdOTG in otg descriptor to identify the OTG and EH
supplement release number with which the OTG device is compliant, this
patch adds structure usb_otg20_descriptor for OTG 2.0 and above.
Signed-off-by: Macpaul Lin <macpaul@gmail.com>
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This patch adds names for missing irq types to the trace events.
In order to identify adapter irqs, the define is moved from
interrupt.c to the other basic irq defines in uapi/linux/kvm.h.
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
|
|
Add support for the three ARS DSM commands:
- Query ARS Capabilities - Queries the firmware to check if a given
range supports scrub, and if so, which type (persistent vs. volatile)
- Start ARS - Starts a scrub for a given range/type
- Query ARS Status - Checks status of a previously started scrub, and
provides the error logs if any.
The commands are described by the example DSM spec at:
http://pmem.io/documents/NVDIMM_DSM_Interface_Example.pdf
Also add these commands to the nfit_test test framework, and return
canned data.
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
