| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Convert struct serial_rs485 comments to kernel doc format and include
it into documentation.
Suggested-by: Andy Shevchenko <[email protected]>
Reviewed-by: Andy Shevchenko <[email protected]>
Reviewed-by: Bagas Sanjaya <[email protected]>
Signed-off-by: Ilpo Järvinen <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Add support for RS-485 multipoint addressing using 9th bit [*]. The
addressing mode is configured through ->rs485_config().
ADDRB in termios indicates 9th bit addressing mode is enabled. In this
mode, 9th bit is used to indicate an address (byte) within the
communication line. ADDRB can only be enabled/disabled through
->rs485_config() that is also responsible for setting the destination and
receiver (filter) addresses.
Add traps to detect unwanted changes to struct serial_rs485 layout using
static_assert().
[*] Technically, RS485 is just an electronic spec and does not itself
specify the 9th bit addressing mode but 9th bit seems at least
"semi-standard" way to do addressing with RS485.
Signed-off-by: Ilpo Järvinen <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The Cyclades driver was orphaned by commit d459883e6c54 (MAINTAINERS:
remove two dead e-mail) 13 years ago. Noone stepped up to take care of
them and to fix all the issues the driver has.
On the top of that, there is no way to obtain the firmware for Z cards
from the vendor as cyclades.com ceased to exist.
So it's time to drop the driver with all its traces.
Signed-off-by: Jiri Slaby <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Add the ISO7816 ioctl and associated accessors and data structure.
Drivers can then use this common implementation to handle ISO7816
(smart cards).
Signed-off-by: Nicolas Ferre <[email protected]>
[[email protected]: squash and rebase, removal of gpios, checkpatch fixes]
Signed-off-by: Ludovic Desroches <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Many user space API headers have licensing information, which is either
incomplete, badly formatted or just a shorthand for referring to the
license under which the file is supposed to be. This makes it hard for
compliance tools to determine the correct license.
Update these files with an SPDX license identifier. The identifier was
chosen based on the license information in the file.
GPL/LGPL licensed headers get the matching GPL/LGPL SPDX license
identifier with the added 'WITH Linux-syscall-note' exception, which is
the officially assigned exception identifier for the kernel syscall
exception:
NOTE! This copyright does *not* cover user programs that use kernel
services by normal system calls - this is merely considered normal use
of the kernel, and does *not* fall under the heading of "derived work".
This exception makes it possible to include GPL headers into non GPL
code, without confusing license compliance tools.
Headers which have either explicit dual licensing or are just licensed
under a non GPL license are updated with the corresponding SPDX
identifier and the GPLv2 with syscall exception identifier. The format
is:
((GPL-2.0 WITH Linux-syscall-note) OR SPDX-ID-OF-OTHER-LICENSE)
SPDX license identifiers are a legally binding shorthand, which can be
used instead of the full boiler plate text. The update does not remove
existing license information as this has to be done on a case by case
basis and the copyright holders might have to be consulted. This will
happen in a separate step.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne. See the previous patch in this series for the
methodology of how this patch was researched.
Reviewed-by: Kate Stewart <[email protected]>
Reviewed-by: Philippe Ombredanne <[email protected]>
Reviewed-by: Thomas Gleixner <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The Siemens IOT2040 comes with a RS485 interface that allows to enable
or disable bus termination via software. Add a bit to the flags field of
serial_rs485 that applications can set in order to request this feature
from the hardware. This seems generic enough to add it for everyone.
Existing driver will simply ignore it when set.
Signed-off-by: Sascha Weisenberger <[email protected]>
Signed-off-by: Jan Kiszka <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Currently, 8-bit (MMIO) and 32-bit (MMIO32) register interfaces are
supported for the 8250 console, but the 16-bit (MMIO16) is not.
The 8250 UART device on my board is connected to a 16-bit bus and
my main motivation is to use earlycon with it.
(Refer to arch/arm/boot/dts/uniphier-support-card.dtsi)
Signed-off-by: Masahiro Yamada <[email protected]>
Reviewed-by: Peter Hurley <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
ioctl(TIOCGSERIAL|TIOCSSERIAL) report and can change the port->iotype.
UART drivers use the UPIO_* definitions, but the uapi header defines
parallel values and userspace uses these parallel values for ioctls;
thus the userspace values are definitive.
Define UPIO_* iotypes in terms of the uapi defines, SERIAL_IO_*;
extend the uapi defines to include all values in use by the serial
core.
Signed-off-by: Peter Hurley <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Signed-off-by: David Howells <[email protected]>
Acked-by: Arnd Bergmann <[email protected]>
Acked-by: Thomas Gleixner <[email protected]>
Acked-by: Michael Kerrisk <[email protected]>
Acked-by: Paul E. McKenney <[email protected]>
Acked-by: Dave Jones <[email protected]>
|