| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Factor out two busy poll related helpers for late reuse, and remove
a command that isn't very helpful, especially with the __poll_t
annotations in place.
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5e-updates-2018-05-19
This series contains updates for mlx5e netdevice driver with one subject,
DSCP to priority mapping, in the first patch Huy adds the needed API in
dcbnl, the second patch adds the needed mlx5 core capability bits for the
feature, and all other patches are mlx5e (netdev) only changes to add
support for the feature.
From: Huy Nguyen
Dscp to priority mapping for Ethernet packet:
These patches enable differentiated services code point (dscp) to
priority mapping for Ethernet packet. Once this feature is
enabled, the packet is routed to the corresponding priority based on its
dscp. User can combine this feature with priority flow control (pfc)
feature to have priority flow control based on the dscp.
Firmware interface:
Mellanox firmware provides two control knobs for this feature:
QPTS register allow changing the trust state between dscp and
pcp mode. The default is pcp mode. Once in dscp mode, firmware will
route the packet based on its dscp value if the dscp field exists.
QPDPM register allow mapping a specific dscp (0 to 63) to a
specific priority (0 to 7). By default, all the dscps are mapped to
priority zero.
Software interface:
This feature is controlled via application priority TLV. IEEE
specification P802.1Qcd/D2.1 defines priority selector id 5 for
application priority TLV. This APP TLV selector defines DSCP to priority
map. This APP TLV can be sent by the switch or can be set locally using
software such as lldptool. In mlx5 drivers, we add the support for net
dcb's getapp and setapp call back. Mlx5 driver only handles the selector
id 5 application entry (dscp application priority application entry).
If user sends multiple dscp to priority APP TLV entries on the same
dscp, the last sent one will take effect. All the previous sent will be
deleted.
This attribute combined with pfc attribute allows advanced user to
fine tune the qos setting for specific priority queue. For example,
user can give dedicated buffer for one or more priorities or user
can give large buffer to certain priorities.
The dcb buffer configuration will be controlled by lldptool.
>> lldptool -T -i eth2 -V BUFFER prio 0,2,5,7,1,2,3,6
maps priorities 0,1,2,3,4,5,6,7 to receive buffer 0,2,5,7,1,2,3,6
>> lldptool -T -i eth2 -V BUFFER size 87296,87296,0,87296,0,0,0,0
sets receive buffer size for buffer 0,1,2,3,4,5,6,7 respectively
After discussion on mailing list with Jakub, Jiri, Ido and John, we agreed to
choose dcbnl over devlink interface since this feature is intended to set
port attributes which are governed by the netdev instance of that port, where
devlink API is more suitable for global ASIC configurations.
The firmware trust state (in QPTS register) is changed based on the
number of dscp to priority application entries. When the first dscp to
priority application entry is added by the user, the trust state is
changed to dscp. When the last dscp to priority application entry is
deleted by the user, the trust state is changed to pcp.
When the port is in DSCP trust state, the transmit queue is selected
based on the dscp of the skb.
When the port is in DSCP trust state and vport inline mode is not NONE,
firmware requires mlx5 driver to copy the IP header to the
wqe ethernet segment inline header if the skb has it.
This is done by changing the transmit queue sq's min inline mode to L3.
Note that the min inline mode of sqs that belong to other features
such as xdpsq, icosq are not modified.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 05f0fe6b74db ("RCU, workqueue: Implement rcu_work") introduces
new API's for dispatching work in a RCU callback. Now we can just
switch to the new API's for tc filters. This could get rid of a lot
of code.
Cc: Tejun Heo <tj@kernel.org>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Alexei Starovoitov says:
====================
pull-request: bpf-next 2018-05-24
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Björn Töpel cleans up AF_XDP (removes rebind, explicit cache alignment from uapi, etc).
2) David Ahern adds mtu checks to bpf_ipv{4,6}_fib_lookup() helpers.
3) Jesper Dangaard Brouer adds bulking support to ndo_xdp_xmit.
4) Jiong Wang adds support for indirect and arithmetic shifts to NFP
5) Martin KaFai Lau cleans up BTF uapi and makes the btf_header extensible.
6) Mathieu Xhonneux adds an End.BPF action to seg6local with BPF helpers allowing
to edit/grow/shrink a SRH and apply on a packet generic SRv6 actions.
7) Sandipan Das adds support for bpf2bpf function calls in ppc64 JIT.
8) Yonghong Song adds BPF_TASK_FD_QUERY command for introspection of tracing events.
9) other misc fixes from Gustavo A. R. Silva, Sirio Balmelli, John Fastabend, and Magnus Karlsson
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When sending an xdp_frame through xdp_do_redirect call, then error
cases can happen where the xdp_frame needs to be dropped, and
returning an -errno code isn't sufficient/possible any-longer
(e.g. for cpumap case). This is already fully supported, by simply
calling xdp_return_frame.
This patch is an optimization, which provides xdp_return_frame_rx_napi,
which is a faster variant for these error cases. It take advantage of
the protection provided by XDP RX running under NAPI protection.
This change is mostly relevant for drivers using the page_pool
allocator as it can take advantage of this. (Tested with mlx5).
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
In this patch, we add dcbnl buffer attribute to allow user
change the NIC's buffer configuration such as priority
to buffer mapping and buffer size of individual buffer.
This attribute combined with pfc attribute allows advanced user to
fine tune the qos setting for specific priority queue. For example,
user can give dedicated buffer for one or more priorities or user
can give large buffer to certain priorities.
The dcb buffer configuration will be controlled by lldptool.
lldptool -T -i eth2 -V BUFFER prio 0,2,5,7,1,2,3,6
maps priorities 0,1,2,3,4,5,6,7 to receive buffer 0,2,5,7,1,2,3,6
lldptool -T -i eth2 -V BUFFER size 87296,87296,0,87296,0,0,0,0
sets receive buffer size for buffer 0,1,2,3,4,5,6,7 respectively
After discussion on mailing list with Jakub, Jiri, Ido and John, we agreed to
choose dcbnl over devlink interface since this feature is intended to set
port attributes which are governed by the netdev instance of that port, where
devlink API is more suitable for global ASIC configurations.
We present an use case scenario where dcbnl buffer attribute configured
by advance user helps reduce the latency of messages of different sizes.
Scenarios description:
On ConnectX-5, we run latency sensitive traffic with
small/medium message sizes ranging from 64B to 256KB and bandwidth sensitive
traffic with large messages sizes 512KB and 1MB. We group small, medium,
and large message sizes to their own pfc enables priorities as follow.
Priorities 1 & 2 (64B, 256B and 1KB)
Priorities 3 & 4 (4KB, 8KB, 16KB, 64KB, 128KB and 256KB)
Priorities 5 & 6 (512KB and 1MB)
By default, ConnectX-5 maps all pfc enabled priorities to a single
lossless fixed buffer size of 50% of total available buffer space. The
other 50% is assigned to lossy buffer. Using dcbnl buffer attribute,
we create three equal size lossless buffers. Each buffer has 25% of total
available buffer space. Thus, the lossy buffer size reduces to 25%. Priority
to lossless buffer mappings are set as follow.
Priorities 1 & 2 on lossless buffer #1
Priorities 3 & 4 on lossless buffer #2
Priorities 5 & 6 on lossless buffer #3
We observe improvements in latency for small and medium message sizes
as follows. Please note that the large message sizes bandwidth performance is
reduced but the total bandwidth remains the same.
256B message size (42 % latency reduction)
4K message size (21% latency reduction)
64K message size (16% latency reduction)
CC: Ido Schimmel <idosch@idosch.org>
CC: Jakub Kicinski <jakub.kicinski@netronome.com>
CC: Jiri Pirko <jiri@resnulli.us>
CC: Or Gerlitz <gerlitz.or@gmail.com>
CC: Parav Pandit <parav@mellanox.com>
CC: Aron Silverton <aron.silverton@oracle.com>
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The BPF seg6local hook should be powerful enough to enable users to
implement most of the use-cases one could think of. After some thinking,
we figured out that the following actions should be possible on a SRv6
packet, requiring 3 specific helpers :
- bpf_lwt_seg6_store_bytes: Modify non-sensitive fields of the SRH
- bpf_lwt_seg6_adjust_srh: Allow to grow or shrink a SRH
(to add/delete TLVs)
- bpf_lwt_seg6_action: Apply some SRv6 network programming actions
(specifically End.X, End.T, End.B6 and
End.B6.Encap)
The specifications of these helpers are provided in the patch (see
include/uapi/linux/bpf.h).
The non-sensitive fields of the SRH are the following : flags, tag and
TLVs. The other fields can not be modified, to maintain the SRH
integrity. Flags, tag and TLVs can easily be modified as their validity
can be checked afterwards via seg6_validate_srh. It is not allowed to
modify the segments directly. If one wants to add segments on the path,
he should stack a new SRH using the End.B6 action via
bpf_lwt_seg6_action.
Growing, shrinking or editing TLVs via the helpers will flag the SRH as
invalid, and it will have to be re-validated before re-entering the IPv6
layer. This flag is stored in a per-CPU buffer, along with the current
header length in bytes.
Storing the SRH len in bytes in the control block is mandatory when using
bpf_lwt_seg6_adjust_srh. The Header Ext. Length field contains the SRH
len rounded to 8 bytes (a padding TLV can be inserted to ensure the 8-bytes
boundary). When adding/deleting TLVs within the BPF program, the SRH may
temporary be in an invalid state where its length cannot be rounded to 8
bytes without remainder, hence the need to store the length in bytes
separately. The caller of the BPF program can then ensure that the SRH's
final length is valid using this value. Again, a final SRH modified by a
BPF program which doesn’t respect the 8-bytes boundary will be discarded
as it will be considered as invalid.
Finally, a fourth helper is provided, bpf_lwt_push_encap, which is
available from the LWT BPF IN hook, but not from the seg6local BPF one.
This helper allows to encapsulate a Segment Routing Header (either with
a new outer IPv6 header, or by inlining it directly in the existing IPv6
header) into a non-SRv6 packet. This helper is required if we want to
offer the possibility to dynamically encapsulate a SRH for non-SRv6 packet,
as the BPF seg6local hook only works on traffic already containing a SRH.
This is the BPF equivalent of the seg6 LWT infrastructure, which achieves
the same purpose but with a static SRH per route.
These helpers require CONFIG_IPV6=y (and not =m).
Signed-off-by: Mathieu Xhonneux <m.xhonneux@gmail.com>
Acked-by: David Lebrun <dlebrun@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
The function lookup_nexthop is essential to implement most of the seg6local
actions. As we want to provide a BPF helper allowing to apply some of these
actions on the packet being processed, the helper should be able to call
this function, hence the need to make it public.
Moreover, if one argument is incorrect or if the next hop can not be found,
an error should be returned by the BPF helper so the BPF program can adapt
its processing of the packet (return an error, properly force the drop,
...). This patch hence makes this function return dst->error to indicate a
possible error.
Signed-off-by: Mathieu Xhonneux <m.xhonneux@gmail.com>
Acked-by: David Lebrun <dlebrun@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
include/net/seg6.h cannot be included in a source file if CONFIG_IPV6 is
not enabled:
include/net/seg6.h: In function 'seg6_pernet':
>> include/net/seg6.h:52:14: error: 'struct net' has no member named
'ipv6'; did you mean 'ipv4'?
return net->ipv6.seg6_data;
^~~~
ipv4
This commit makes seg6_pernet return NULL if IPv6 is not compiled, hence
allowing seg6.h to be included regardless of the configuration.
Signed-off-by: Mathieu Xhonneux <m.xhonneux@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for your net-next
tree, they are:
1) Remove obsolete nf_log tracing from nf_tables, from Florian Westphal.
2) Add support for map lookups to numgen, random and hash expressions,
from Laura Garcia.
3) Allow to register nat hooks for iptables and nftables at the same
time. Patchset from Florian Westpha.
4) Timeout support for rbtree sets.
5) ip6_rpfilter works needs interface for link-local addresses, from
Vincent Bernat.
6) Add nf_ct_hook and nf_nat_hook structures and use them.
7) Do not drop packets on packets raceing to insert conntrack entries
into hashes, this is particularly a problem in nfqueue setups.
8) Address fallout from xt_osf separation to nf_osf, patches
from Florian Westphal and Fernando Mancera.
9) Remove reference to struct nft_af_info, which doesn't exist anymore.
From Taehee Yoo.
This batch comes with is a conflict between 25fd386e0bc0 ("netfilter:
core: add missing __rcu annotation") in your tree and 2c205dd3981f
("netfilter: add struct nf_nat_hook and use it") coming in this batch.
This conflict can be solved by leaving the __rcu tag on
__netfilter_net_init() - added by 25fd386e0bc0 - and remove all code
related to nf_nat_decode_session_hook - which is gone after
2c205dd3981f, as described by:
diff --cc net/netfilter/core.c
index e0ae4aae96f5,206fb2c4c319..168af54db975
--- a/net/netfilter/core.c
+++ b/net/netfilter/core.c
@@@ -611,7 -580,13 +611,8 @@@ const struct nf_conntrack_zone nf_ct_zo
EXPORT_SYMBOL_GPL(nf_ct_zone_dflt);
#endif /* CONFIG_NF_CONNTRACK */
- static void __net_init __netfilter_net_init(struct nf_hook_entries **e, int max)
-#ifdef CONFIG_NF_NAT_NEEDED
-void (*nf_nat_decode_session_hook)(struct sk_buff *, struct flowi *);
-EXPORT_SYMBOL(nf_nat_decode_session_hook);
-#endif
-
+ static void __net_init
+ __netfilter_net_init(struct nf_hook_entries __rcu **e, int max)
{
int h;
I can also merge your net-next tree into nf-next, solve the conflict and
resend the pull request if you prefer so.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
For this round, we have various things all over the place, notably
* a fix for a race in aggregation, which I want to let
bake for a bit longer before sending to stable
* some new statistics (ACK RSSI, TXQ)
* TXQ configuration
* preparations for HE, particularly radiotap
* replace confusing "country IE" by "country element" since it's
not referring to Ireland
Note that I merged net-next to get a fix from mac80211 that got
there via net, to apply one patch that would otherwise conflict.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is a followup to fib rules sport, dport and ipproto
match support. Only supports tcp, udp and icmp for ipproto.
Used by fib rule self tests.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The struct nft_af_info was removed.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Use NL80211_CMD_UPDATE_CONNECT_PARAMS to update new ERP information,
Association IEs and the Authentication type to driver / firmware which
will be used in subsequent roamings.
Signed-off-by: Vidyullatha Kanchanapally <vidyullatha@codeaurora.org>
[arend: extended fils-sk kernel doc and added check in wiphy_register()]
Reviewed-by: Jithu Jance <jithu.jance@broadcom.com>
Reviewed-by: Eylon Pedinovsky <eylon.pedinovsky@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In case of FILS shared key offload the parameters can change
upon roaming of which user-space needs to be notified.
Reviewed-by: Jithu Jance <jithu.jance@broadcom.com>
Reviewed-by: Eylon Pedinovsky <eylon.pedinovsky@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Put FILS related parameters into their own struct definition so
it can be reused for roam events in subsequent change.
Reviewed-by: Jithu Jance <jithu.jance@broadcom.com>
Reviewed-by: Eylon Pedinovsky <eylon.pedinovsky@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
There are specific cases, such as SAE authentication exchange, that
might require long duration to complete. For such cases, add support
for indicating to the driver the required duration of the prepare_tx()
operation, so the driver would still be able to complete the frame
exchange.
Currently, indicate the duration only for SAE authentication exchange,
as SAE authentication can take up to 2000 msec (as defined in IEEE
P802.11-REVmd D1.0 p. 3504).
As the patch modified the prepare_tx() callback API, also modify
the relevant code in iwlwifi.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Bring in net-next which had pulled in net, so I have the changes
from mac80211 and can apply a patch that would otherwise conflict.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Move decode_session() and parse_nat_setup_hook() indirections to struct
nf_nat_hook structure.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Currently the packet rewrite and instantiation of nat NULL bindings
happens from the protocol specific nat backend.
Invocation occurs either via ip(6)table_nat or the nf_tables nat chain type.
Invocation looks like this (simplified):
NF_HOOK()
|
`---iptable_nat
|
`---> nf_nat_l3proto_ipv4 -> nf_nat_packet
|
new packet? pass skb though iptables nat chain
|
`---> iptable_nat: ipt_do_table
In nft case, this looks the same (nft_chain_nat_ipv4 instead of
iptable_nat).
This is a problem for two reasons:
1. Can't use iptables nat and nf_tables nat at the same time,
as the first user adds a nat binding (nf_nat_l3proto_ipv4 adds a
NULL binding if do_table() did not find a matching nat rule so we
can detect post-nat tuple collisions).
2. If you use e.g. nft_masq, snat, redir, etc. uses must also register
an empty base chain so that the nat core gets called fro NF_HOOK()
to do the reverse translation, which is neither obvious nor user
friendly.
After this change, the base hook gets registered not from iptable_nat or
nftables nat hooks, but from the l3 nat core.
iptables/nft nat base hooks get registered with the nat core instead:
NF_HOOK()
|
`---> nf_nat_l3proto_ipv4 -> nf_nat_packet
|
new packet? pass skb through iptables/nftables nat chains
|
+-> iptables_nat: ipt_do_table
+-> nft nat chain x
`-> nft nat chain y
The nat core deals with null bindings and reverse translation.
When no mapping exists, it calls the registered nat lookup hooks until
one creates a new mapping.
If both iptables and nftables nat hooks exist, the first matching
one is used (i.e., higher priority wins).
Also, nft users do not need to create empty nat hooks anymore,
nat core always registers the base hooks that take care of reverse/reply
translation.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This adds the infrastructure to register nat hooks with the nat core
instead of the netfilter core.
nat hooks are used to configure nat bindings. Such hooks are registered
from ip(6)table_nat or by the nftables core when a nat chain is added.
After next patch, nat hooks will be registered with nf_nat instead of
netfilter core. This allows to use many nat lookup functions at the
same time while doing the real packet rewrite (nat transformation) in
one place.
This change doesn't convert the intended users yet to ease review.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Will be used in followup patch when nat types no longer
use nf_register_net_hook() but will instead register with the nat core.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Copy-pasted, both l3 helpers almost use same code here.
Split out the common part into an 'inet' helper.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Bring consistency to ipv6 route replace and append semantics.
Remove rt6_qualify_for_ecmp which is just guess work. It fails in 2 cases:
1. can not replace a route with a reject route. Existing code appends
a new route instead of replacing the existing one.
2. can not have a multipath route where a leg uses a dev only nexthop
Existing use cases affected by this change:
1. adding a route with existing prefix and metric using NLM_F_CREATE
without NLM_F_APPEND or NLM_F_EXCL (ie., what iproute2 calls
'prepend'). Existing code auto-determines that the new nexthop can
be appended to an existing route to create a multipath route. This
change breaks that by requiring the APPEND flag for the new route
to be added to an existing one. Instead the prepend just adds another
route entry.
2. route replace. Existing code replaces first matching multipath route
if new route is multipath capable and fallback to first matching
non-ECMP route (reject or dev only route) in case one isn't available.
New behavior replaces first matching route. (Thanks to Ido for spotting
this one)
Note: Newer iproute2 is needed to display multipath routes with a dev-only
nexthop. This is due to a bug in iproute2 and parsing nexthops.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now sctp uses inet_dgram_connect as its proto_ops .connect, and the flags
param can't be passed into its proto .connect where this flags is really
needed.
sctp works around it by getting flags from socket file in __sctp_connect.
It works for connecting from userspace, as inherently the user sock has
socket file and it passes f_flags as the flags param into the proto_ops
.connect.
However, the sock created by sock_create_kern doesn't have a socket file,
and it passes the flags (like O_NONBLOCK) by using the flags param in
kernel_connect, which calls proto_ops .connect later.
So to fix it, this patch defines a new proto_ops .connect for sctp,
sctp_inet_connect, which calls __sctp_connect() directly with this
flags param. After this, the sctp's proto .connect can be removed.
Note that sctp_inet_connect doesn't need to do some checks that are not
needed for sctp, which makes thing better than with inet_dgram_connect.
Suggested-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the kernel-doc missed earlier.
Fixes: 52539ca89f36 ("cfg80211: Expose TXQ stats and parameters to userspace")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Determine path MTU from a FIB lookup result. Logic is based on
ip6_dst_mtu_forward plus lookup of nexthop exception.
Add ip6_dst_mtu_forward to ipv6_stubs to handle access by core
bpf code.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Determine path MTU from a FIB lookup result. Logic is a distillation of
ip_dst_mtu_maybe_forward.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
S390 bpf_jit.S is removed in net-next and had changes in 'net',
since that code isn't used any more take the removal.
TLS data structures split the TX and RX components in 'net-next',
put the new struct members from the bug fix in 'net' into the RX
part.
The 'net-next' tree had some reworking of how the ERSPAN code works in
the GRE tunneling code, overlapping with a one-line headroom
calculation fix in 'net'.
Overlapping changes in __sock_map_ctx_update_elem(), keep the bits
that read the prog members via READ_ONCE() into local variables
before using them.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before the patch, the erspan BSO bit (Bad/Short/Oversized) is not
handled. BSO has 4 possible values:
00 --> Good frame with no error, or unknown integrity
11 --> Payload is a Bad Frame with CRC or Alignment Error
01 --> Payload is a Short Frame
10 --> Payload is an Oversized Frame
Based the short/oversized definitions in RFC1757, the patch sets
the bso bit based on the mirrored packet's size.
Reported-by: Xiaoyan Jin <xiaoyanj@vmware.com>
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
Johan Hedberg says:
====================
pull request: bluetooth-next 2018-05-18
Here's the first bluetooth-next pull request for the 4.18 kernel:
- Refactoring of the btbcm driver
- New USB IDs for QCA_ROME and LiteOn controllers
- Buffer overflow fix if the controller sends invalid advertising data length
- Various cleanups & fixes for Qualcomm controllers
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Each driver implements physical port name generation by itself. However
as devlink has all needed info, it can easily do the job for all its
users. So implement this helper in devlink.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Devlink ports can have specific flavour according to the purpose of use.
This patch extend attrs_set so the driver can say which flavour port
has. Initial flavours are:
physical, cpu, dsa
User can query this to see right away what is the purpose of each port.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change existing setter for split port information into more generic
attrs setter. Alongside with that, allow to set port number and subport
number for split ports.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This per netns sysctl allows for TCP SACK compression fine-tuning.
This limits number of SACK that can be compressed.
Using 0 disables SACK compression.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This per netns sysctl allows for TCP SACK compression fine-tuning.
Its default value is 1,000,000, or 1 ms to meet TSO autosizing period.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When TCP receives an out-of-order packet, it immediately sends
a SACK packet, generating network load but also forcing the
receiver to send 1-MSS pathological packets, increasing its
RTX queue length/depth, and thus processing time.
Wifi networks suffer from this aggressive behavior, but generally
speaking, all these SACK packets add fuel to the fire when networks
are under congestion.
This patch adds a high resolution timer and tp->compressed_ack counter.
Instead of sending a SACK, we program this timer with a small delay,
based on RTT and capped to 1 ms :
delay = min ( 5 % of RTT, 1 ms)
If subsequent SACKs need to be sent while the timer has not yet
expired, we simply increment tp->compressed_ack.
When timer expires, a SACK is sent with the latest information.
Whenever an ACK is sent (if data is sent, or if in-order
data is received) timer is canceled.
Note that tcp_sack_new_ofo_skb() is able to force a SACK to be sent
if the sack blocks need to be shuffled, even if the timer has not
expired.
A new SNMP counter is added in the following patch.
Two other patches add sysctls to allow changing the 1,000,000 and 44
values that this commit hard-coded.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Socket can not disappear under us.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Clean up SPDX-License-Identifier and removing licensing leftovers.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
This fixes memory leaks in cases where we got the station
info but failed sending it out properly.
Fixes: 8689c051a201 ("cfg80211: dynamically allocate per-tid stats for station info")
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
With the addition of TXQ stats in the per-tid statistics the struct
station_info grew significantly. This resulted in stack size warnings
due to the structure itself being above the limit for the warnings.
Add an allocation function that those who want to provide per-tid
stats should use to allocate the tid array, i.e.
struct station_info::pertid.
Cc: Toke Høiland-Jørgensen <toke@toke.dk>
Fixes: 52539ca89f36 ("cfg80211: Expose TXQ stats and parameters to userspace")
Signed-off-by: Arend van Spriel <aspriel@gmail.com>
[johannes: fix missing BIT() and logic by removing]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This function allows to send a HCI command without expecting any
controller event/response in return. This is allowed for vendor-
specific commands only.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Create and export a new helper tcp_rack_skb_timeout and move tcp_is_rack
to prepare the final RTO change.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Reviewed-by: Priyaranjan Jha <priyarjha@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The previous approach for the lost and retransmit bits was to
wipe the slate clean: zero all the lost and retransmit bits,
correspondingly zero the lost_out and retrans_out counters, and
then add back the lost bits (and correspondingly increment lost_out).
The new approach is to treat this very much like marking packets
lost in fast recovery. We don’t wipe the slate clean. We just say
that for all packets that were not yet marked sacked or lost, we now
mark them as lost in exactly the same way we do for fast recovery.
This fixes the lost retransmit accounting at RTO time and greatly
simplifies the RTO code by sharing much of the logic with Fast
Recovery.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Reviewed-by: Priyaranjan Jha <priyarjha@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is a rewrite of NewReno loss recovery implementation that is
simpler and standalone for readability and better performance by
using less states.
Note that NewReno refers to RFC6582 as a modification to the fast
recovery algorithm. It is used only if the connection does not
support SACK in Linux. It should not to be confused with the Reno
(AIMD) congestion control.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Reviewed-by: Priyaranjan Jha <priyarjha@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for the classic DUPACK threshold rule
(#DupThresh) in RACK.
When the number of packets SACKed is greater or equal to the
threshold, RACK sets the reordering window to zero which would
immediately mark all the unsacked packets below the highest SACKed
sequence lost. Since this approach is known to not work well with
reordering, RACK only uses it if no reordering has been observed.
The DUPACK threshold rule is a particularly useful extension to the
fast recoveries triggered by RACK reordering timer. For example
data-center transfers where the RTT is much smaller than a timer
tick, or high RTT path where the default RTT/4 may take too long.
Note that this patch differs slightly from RFC6675. RFC6675
considers a packet lost when at least #DupThresh higher-sequence
packets are SACKed.
With RACK, for connections that have seen reordering, RACK
continues to use a dynamically-adaptive time-based reordering
window to detect losses. But for connections on which we have not
yet seen reordering, this patch considers a packet lost when at
least one higher sequence packet is SACKed and the total number
of SACKed packets is at least DupThresh. For example, suppose a
connection has not seen reordering, and sends 10 packets, and
packets 3, 5, 7 are SACKed. RFC6675 considers packets 1 and 2
lost. RACK considers packets 1, 2, 4, 6 lost.
There is some small risk of spurious retransmits here due to
reordering. However, this is mostly limited to the first flight of
a connection on which the sender receives SACKs from reordering.
And RFC 6675 and FACK loss detection have a similar risk on the
first flight with reordering (it's just that the risk of spurious
retransmits from reordering was slightly narrower for those older
algorithms due to the margin of 3*MSS).
Also the minimum reordering window is reduced from 1 msec to 0
to recover quicker on short RTT transfers. Therefore RACK is more
aggressive in marking packets lost during recovery to reduce the
reordering window timeouts.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Reviewed-by: Priyaranjan Jha <priyarjha@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
scatterlist code expects virt_to_page() to work, which fails with
CONFIG_VMAP_STACK=y.
Fixes: c46234ebb4d1e ("tls: RX path for ktls")
Signed-off-by: Matt Mullins <mmullins@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
So that we can use lockdep on it.
The newly introduced sequence lock has the same scope of busylock,
so it shares the same lockdep annotation, but it's only used for
NOLOCK qdiscs.
With this changeset we acquire such lock in the control path around
flushing operation (qdisc reset), to allow more NOLOCK qdisc perf
improvement in the next patch.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-05-17
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Provide a new BPF helper for doing a FIB and neighbor lookup
in the kernel tables from an XDP or tc BPF program. The helper
provides a fast-path for forwarding packets. The API supports
IPv4, IPv6 and MPLS protocols, but currently IPv4 and IPv6 are
implemented in this initial work, from David (Ahern).
2) Just a tiny diff but huge feature enabled for nfp driver by
extending the BPF offload beyond a pure host processing offload.
Offloaded XDP programs are allowed to set the RX queue index and
thus opening the door for defining a fully programmable RSS/n-tuple
filter replacement. Once BPF decided on a queue already, the device
data-path will skip the conventional RSS processing completely,
from Jakub.
3) The original sockmap implementation was array based similar to
devmap. However unlike devmap where an ifindex has a 1:1 mapping
into the map there are use cases with sockets that need to be
referenced using longer keys. Hence, sockhash map is added reusing
as much of the sockmap code as possible, from John.
4) Introduce BTF ID. The ID is allocatd through an IDR similar as
with BPF maps and progs. It also makes BTF accessible to user
space via BPF_BTF_GET_FD_BY_ID and adds exposure of the BTF data
through BPF_OBJ_GET_INFO_BY_FD, from Martin.
5) Enable BPF stackmap with build_id also in NMI context. Due to the
up_read() of current->mm->mmap_sem build_id cannot be parsed.
This work defers the up_read() via a per-cpu irq_work so that
at least limited support can be enabled, from Song.
6) Various BPF JIT follow-up cleanups and fixups after the LD_ABS/LD_IND
JIT conversion as well as implementation of an optimized 32/64 bit
immediate load in the arm64 JIT that allows to reduce the number of
emitted instructions; in case of tested real-world programs they
were shrinking by three percent, from Daniel.
7) Add ifindex parameter to the libbpf loader in order to enable
BPF offload support. Right now only iproute2 can load offloaded
BPF and this will also enable libbpf for direct integration into
other applications, from David (Beckett).
8) Convert the plain text documentation under Documentation/bpf/ into
RST format since this is the appropriate standard the kernel is
moving to for all documentation. Also add an overview README.rst,
from Jesper.
9) Add __printf verification attribute to the bpf_verifier_vlog()
helper. Though it uses va_list we can still allow gcc to check
the format string, from Mathieu.
10) Fix a bash reference in the BPF selftest's Makefile. The '|& ...'
is a bash 4.0+ feature which is not guaranteed to be available
when calling out to shell, therefore use a more portable variant,
from Joe.
11) Fix a 64 bit division in xdp_umem_reg() by using div_u64()
instead of relying on the gcc built-in, from Björn.
12) Fix a sock hashmap kmalloc warning reported by syzbot when an
overly large key size is used in hashmap then causing overflows
in htab->elem_size. Reject bogus attr->key_size early in the
sock_hash_alloc(), from Yonghong.
13) Ensure in BPF selftests when urandom_read is being linked that
--build-id is always enabled so that test_stacktrace_build_id[_nmi]
won't be failing, from Alexei.
14) Add bitsperlong.h as well as errno.h uapi headers into the tools
header infrastructure which point to one of the arch specific
uapi headers. This was needed in order to fix a build error on
some systems for the BPF selftests, from Sirio.
15) Allow for short options to be used in the xdp_monitor BPF sample
code. And also a bpf.h tools uapi header sync in order to fix a
selftest build failure. Both from Prashant.
16) More formally clarify the meaning of ID in the direct packet access
section of the BPF documentation, from Wang.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently NOLOCK qdiscs pay a measurable overhead to atomically
manipulate the __QDISC_STATE_RUNNING. Such bit is flipped twice per
packet in the uncontended scenario with packet rate below the
line rate: on packed dequeue and on the next, failing dequeue attempt.
This changeset moves the bit manipulation into the qdisc_run_{begin,end}
helpers, so that the bit is now flipped only once per packet, with
measurable performance improvement in the uncontended scenario.
This also allows simplifying the qdisc teardown code path - since
qdisc_is_running() is now effective for each qdisc type - and avoid a
possible race between qdisc_run() and dev_deactivate_many(), as now
the some_qdisc_is_busy() can properly detect NOLOCK qdiscs being busy
dequeuing packets.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|