| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Introduce mtk_wed_buf structure to store both virtual and physical
addresses allocated in mtk_wed_tx_buffer_alloc() routine. This is a
preliminary patch to add WED support for MT7988 SoC since it relies on a
different dma descriptor layout not storing page dma addresses.
Co-developed-by: Sujuan Chen <[email protected]>
Signed-off-by: Sujuan Chen <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Paolo Abeni <[email protected]>
|
|
Rename mtk_rxbm_desc structure in mtk_wed_bm_desc since it will be used
even on tx side by MT7988 SoC.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Paolo Abeni <[email protected]>
|
|
We have data-races while reading np->srcprefs
Switch the field to a plain byte, add READ_ONCE()
and WRITE_ONCE() annotations where needed,
and IPV6_ADDR_PREFERENCES setsockopt() can now be lockless.
Signed-off-by: Eric Dumazet <[email protected]>
Reviewed-by: David Ahern <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Paolo Abeni <[email protected]>
|
|
Marek reports that a deadlock occurs with the AX88772A PHY used on the
ASIX USB network driver:
asix 1-1.4:1.0 (unnamed net_device) (uninitialized): PHY [usb-001:003:10] driver [Asix Electronics AX88772A] (irq=POLL)
Asix Electronics AX88772A usb-001:003:10: attached PHY driver(mii_bus:phy_addr=usb-001:003:10, irq=POLL)
asix 1-1.4:1.0 eth0: register 'asix' at usb-12110000.usb-1.4, ASIX AX88772 USB 2.0 Ethernet, a2:99:b6:cd:11:eb
asix 1-1.4:1.0 eth0: configuring for phy/internal link mode
============================================
WARNING: possible recursive locking detected
6.6.0-rc1-00239-g8da77df649c4-dirty #13949 Not tainted
--------------------------------------------
kworker/3:3/71 is trying to acquire lock:
c6c704cc (&dev->lock){+.+.}-{3:3}, at: phy_start_aneg+0x1c/0x38
but task is already holding lock:
c6c704cc (&dev->lock){+.+.}-{3:3}, at: phy_state_machine+0x100/0x2b8
This is because we now consistently call phy_process_state_change()
while holding phydev->lock, but the AX88772A PHY driver then goes on
to call phy_start_aneg() which tries to grab the same lock - causing
deadlock.
Fix this by exporting the unlocked version, and use this in the PHY
driver instead.
Reported-by: Marek Szyprowski <[email protected]>
Tested-by: Marek Szyprowski <[email protected]>
Fixes: ef113a60d0a9 ("net: phy: call phy_error_precise() while holding the lock")
Signed-off-by: Russell King (Oracle) <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Paolo Abeni <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd into i2c/for-mergewindow
Immutable branch between MFD, I2C and Reboot due for the v6.7 merge window
|
|
Get a null-ptr-deref bug as follows with reproducer [1].
BUG: kernel NULL pointer dereference, address: 0000000000000228
...
RIP: 0010:vlan_dev_hard_header+0x35/0x140 [8021q]
...
Call Trace:
<TASK>
? __die+0x24/0x70
? page_fault_oops+0x82/0x150
? exc_page_fault+0x69/0x150
? asm_exc_page_fault+0x26/0x30
? vlan_dev_hard_header+0x35/0x140 [8021q]
? vlan_dev_hard_header+0x8e/0x140 [8021q]
neigh_connected_output+0xb2/0x100
ip6_finish_output2+0x1cb/0x520
? nf_hook_slow+0x43/0xc0
? ip6_mtu+0x46/0x80
ip6_finish_output+0x2a/0xb0
mld_sendpack+0x18f/0x250
mld_ifc_work+0x39/0x160
process_one_work+0x1e6/0x3f0
worker_thread+0x4d/0x2f0
? __pfx_worker_thread+0x10/0x10
kthread+0xe5/0x120
? __pfx_kthread+0x10/0x10
ret_from_fork+0x34/0x50
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1b/0x30
[1]
$ teamd -t team0 -d -c '{"runner": {"name": "loadbalance"}}'
$ ip link add name t-dummy type dummy
$ ip link add link t-dummy name t-dummy.100 type vlan id 100
$ ip link add name t-nlmon type nlmon
$ ip link set t-nlmon master team0
$ ip link set t-nlmon nomaster
$ ip link set t-dummy up
$ ip link set team0 up
$ ip link set t-dummy.100 down
$ ip link set t-dummy.100 master team0
When enslave a vlan device to team device and team device type is changed
from non-ether to ether, header_ops of team device is changed to
vlan_header_ops. That is incorrect and will trigger null-ptr-deref
for vlan->real_dev in vlan_dev_hard_header() because team device is not
a vlan device.
Cache eth_header_ops in team_setup(), then assign cached header_ops to
header_ops of team net device when its type is changed from non-ether
to ether to fix the bug.
Fixes: 1d76efe1577b ("team: add support for non-ethernet devices")
Suggested-by: Hangbin Liu <[email protected]>
Reviewed-by: Hangbin Liu <[email protected]>
Signed-off-by: Ziyang Xuan <[email protected]>
Reviewed-by: Jiri Pirko <[email protected]>
Reviewed-by: Eric Dumazet <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Paolo Abeni <[email protected]>
|
|
Signed-off-by: Ingo Molnar <[email protected]>
|
|
Pull NFS client fixes from Anna Schumaker:
"Various O_DIRECT related fixes from Trond:
- Error handling
- Locking issues
- Use the correct commit info for joining page groups
- Fixes for rescheduling IO
Sunrpc bad verifier fixes:
- Report EINVAL errors from connect()
- Revalidate creds that the server has rejected
- Revert "SUNRPC: Fail faster on bad verifier"
Misc:
- Fix pNFS session trunking when MDS=DS
- Fix zero-value filehandles for post-open getattr operations
- Fix compiler warning about tautological comparisons
- Revert 'SUNRPC: clean up integer overflow check' before Trond's fix"
* tag 'nfs-for-6.6-2' of git://git.linux-nfs.org/projects/anna/linux-nfs:
SUNRPC: Silence compiler complaints about tautological comparisons
Revert "SUNRPC: clean up integer overflow check"
NFSv4.1: fix zero value filehandle in post open getattr
NFSv4.1: fix pnfs MDS=DS session trunking
Revert "SUNRPC: Fail faster on bad verifier"
SUNRPC: Mark the cred for revalidation if the server rejects it
NFS/pNFS: Report EINVAL errors from connect() to the server
NFS: More fixes for nfs_direct_write_reschedule_io()
NFS: Use the correct commit info in nfs_join_page_group()
NFS: More O_DIRECT accounting fixes for error paths
NFS: Fix O_DIRECT locking issues
NFS: Fix error handling for O_DIRECT write scheduling
|
|
For the write_atomic callback, the console driver may have unsafe
regions that need to be appropriately marked. Provide functions
that accept the nbcon_write_context struct to allow for the driver
to enter and exit unsafe regions.
Also provide a function for drivers to check if they are still the
owner of the console.
Co-developed-by: John Ogness <[email protected]>
Signed-off-by: John Ogness <[email protected]>
Signed-off-by: Thomas Gleixner (Intel) <[email protected]>
Reviewed-by: Petr Mladek <[email protected]>
Signed-off-by: Petr Mladek <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Implement an emit function for nbcon consoles to output printk
messages. It utilizes the lockless printk_get_next_message() and
console_prepend_dropped() functions to retrieve/build the output
message. The emit function includes the required safety points to
check for handover/takeover and calls a new write_atomic callback
of the console driver to output the message. It also includes
proper handling for updating the nbcon console sequence number.
A new nbcon_write_context struct is introduced. This is provided
to the write_atomic callback and includes only the information
necessary for performing atomic writes.
Co-developed-by: John Ogness <[email protected]>
Signed-off-by: John Ogness <[email protected]>
Signed-off-by: Thomas Gleixner (Intel) <[email protected]>
Reviewed-by: Petr Mladek <[email protected]>
Signed-off-by: Petr Mladek <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Add an atomic_long_t field @nbcon_seq to the console struct to
store the sequence number for nbcon consoles. For nbcon consoles
this will be used instead of the non-atomic @seq field. The new
field allows for safe atomic sequence number updates without
requiring any locking.
On 64bit systems the new field stores the full sequence number.
On 32bit systems the new field stores the lower 32 bits of the
sequence number, which are expanded to 64bit as needed by
folding the values based on the sequence numbers available in
the ringbuffer.
For 32bit systems, having a 32bit representation in the console
is sufficient. If a console ever gets more than 2^31 records
behind the ringbuffer then this is the least of the problems.
Co-developed-by: John Ogness <[email protected]>
Signed-off-by: John Ogness <[email protected]>
Signed-off-by: Thomas Gleixner (Intel) <[email protected]>
Signed-off-by: Petr Mladek <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
In case of hostile takeovers it must be ensured that the previous
owner cannot scribble over the output buffer of the emergency/panic
context. This is achieved by:
- Adding a global output buffer instance for the panic context.
This is the only situation where hostile takeovers can occur and
there is always at most 1 panic context.
- Allocating an output buffer per non-boot console upon console
registration. This buffer is used by the console owner when not
in panic context. (For boot consoles, the existing shared global
legacy output buffer is used instead. Boot console printing will
be synchronized with legacy console printing.)
- Choosing the appropriate buffer is handled in the acquire/release
functions.
Co-developed-by: John Ogness <[email protected]>
Signed-off-by: John Ogness <[email protected]>
Signed-off-by: Thomas Gleixner (Intel) <[email protected]>
Reviewed-by: Petr Mladek <[email protected]>
Signed-off-by: Petr Mladek <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Add per console acquire/release functionality.
The state of the console is maintained in the "nbcon_state" atomic
variable.
The console is locked when:
- The 'prio' field contains the priority of the context that owns the
console. Only higher priority contexts are allowed to take over the
lock. A value of 0 (NBCON_PRIO_NONE) means the console is not locked.
- The 'cpu' field denotes on which CPU the console is locked. It is used
to prevent busy waiting on the same CPU. Also it informs the lock owner
that it has lost the lock in a more complex scenario when the lock was
taken over by a higher priority context, released, and taken on another
CPU with the same priority as the interrupted owner.
The acquire mechanism uses a few more fields:
- The 'req_prio' field is used by the handover approach to make the
current owner aware that there is a context with a higher priority
waiting for the friendly handover.
- The 'unsafe' field allows to take over the console in a safe way in the
middle of emitting a message. The field is set only when accessing some
shared resources or when the console device is manipulated. It can be
cleared, for example, after emitting one character when the console
device is in a consistent state.
- The 'unsafe_takeover' field is set when a hostile takeover took the
console in an unsafe state. The console will stay in the unsafe state
until re-initialized.
The acquire mechanism uses three approaches:
1) Direct acquire when the console is not owned or is owned by a lower
priority context and is in a safe state.
2) Friendly handover mechanism uses a request/grant handshake. It is used
when the current owner has lower priority and the console is in an
unsafe state.
The requesting context:
a) Sets its priority into the 'req_prio' field.
b) Waits (with a timeout) for the owning context to unlock the
console.
c) Takes the lock and clears the 'req_prio' field.
The owning context:
a) Observes the 'req_prio' field set on exit from the unsafe
console state.
b) Gives up console ownership by clearing the 'prio' field.
3) Unsafe hostile takeover allows to take over the lock even when the
console is an unsafe state. It is used only in panic() by the final
attempt to flush consoles in a try and hope mode.
Note that separate record buffers are used in panic(). As a result,
the messages can be read and formatted without any risk even after
using the hostile takeover in unsafe state.
The release function simply clears the 'prio' field.
All operations on @console::nbcon_state are atomic cmpxchg based to
handle concurrency.
The acquire/release functions implement only minimal policies:
- Preference for higher priority contexts.
- Protection of the panic CPU.
All other policy decisions must be made at the call sites:
- What is marked as an unsafe section.
- Whether to spin-wait if there is already an owner and the console is
in an unsafe state.
- Whether to attempt an unsafe hostile takeover.
The design allows to implement the well known:
acquire()
output_one_printk_record()
release()
The output of one printk record might be interrupted with a higher priority
context. The new owner is supposed to reprint the entire interrupted record
from scratch.
Co-developed-by: John Ogness <[email protected]>
Signed-off-by: John Ogness <[email protected]>
Signed-off-by: Thomas Gleixner (Intel) <[email protected]>
Signed-off-by: Petr Mladek <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
The current console/printk subsystem is protected by a Big Kernel Lock,
(aka console_lock) which has ill defined semantics and is more or less
stateless. This puts severe limitations on the console subsystem and
makes forced takeover and output in emergency and panic situations a
fragile endeavour that is based on try and pray.
The goal of non-BKL (nbcon) consoles is to break out of the console lock
jail and to provide a new infrastructure that avoids the pitfalls and
also allows console drivers to be gradually converted over.
The proposed infrastructure aims for the following properties:
- Per console locking instead of global locking
- Per console state that allows to make informed decisions
- Stateful handover and takeover
As a first step, state is added to struct console. The per console state
is an atomic_t using a 32bit bit field.
Reserve state bits, which will be populated later in the series. Wire
it up into the console register/unregister functionality.
It was decided to use a bitfield because using a plain u32 with
mask/shift operations resulted in uncomprehensible code.
Co-developed-by: John Ogness <[email protected]>
Signed-off-by: John Ogness <[email protected]>
Signed-off-by: Thomas Gleixner (Intel) <[email protected]>
Reviewed-by: Petr Mladek <[email protected]>
Signed-off-by: Petr Mladek <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Add sw fallback of tx checksum calculation for those tx queues that
don't support tx checksum offloading. DW xGMAC IP can be synthesized
such that it can support tx checksum offloading only for a few
initial tx queues. Also as Serge pointed out, for the DW QoS IP, tx
coe can be individually configured for each tx queue.
So when tx coe is enabled, for any tx queue that doesn't support
tx coe with 'coe-unsupported' flag set will have a sw fallback
happen in the driver for tx checksum calculation when any packets to
be transmitted on these tx queues.
Signed-off-by: Rohan G Thomas <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This reverts commit 3af5ae22030cb59fab4fba35f5a2b62f47e14df9.
ceph_mds_request_args_ext was already (and remains to be) a union. An
additional anonymous union inside is bogus:
union ceph_mds_request_args_ext {
union {
union ceph_mds_request_args old;
struct { ... } __attribute__ ((packed)) setattr_ext;
};
}
Signed-off-by: Ilya Dryomov <[email protected]>
Reviewed-by: Xiubo Li <[email protected]>
|
|
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct ceph_monmap.
Additionally, since the element count member must be set before accessing
the annotated flexible array member, move its initialization earlier.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Cc: Ilya Dryomov <[email protected]>
Cc: Xiubo Li <[email protected]>
Cc: Jeff Layton <[email protected]>
Cc: "David S. Miller" <[email protected]>
Cc: Eric Dumazet <[email protected]>
Cc: Jakub Kicinski <[email protected]>
Cc: Paolo Abeni <[email protected]>
Cc: [email protected]
Cc: [email protected]
Signed-off-by: Kees Cook <[email protected]>
Reviewed-by: Gustavo A. R. Silva <[email protected]>
Reviewed-by: Xiubo Li <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <[email protected]>
Reviewed-by: Ilpo Järvinen <[email protected]>
Signed-off-by: John Ogness <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
Provide wrapper functions for spin_[un]lock*(port->lock) invocations so
that the console mechanics can be applied later on at a single place and
does not require to copy the same logic all over the drivers.
Signed-off-by: Thomas Gleixner <[email protected]>
Reviewed-by: Ilpo Järvinen <[email protected]>
Signed-off-by: John Ogness <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Similar to what we do in the AdminQ, check for devcmd health
while waiting for an answer.
Signed-off-by: Shannon Nelson <[email protected]>
Reviewed-by: Brett Creeley <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
In preparation for freezer to also use saved_state, remove the
CONFIG_PREEMPT_RT compilation guard around saved_state.
On the arm64 platform I tested which did not have CONFIG_PREEMPT_RT,
there was no statistically significant deviation by applying this patch.
Test methodology:
perf bench sched message -g 40 -l 40
Signed-off-by: Elliot Berman <[email protected]>
Signed-off-by: Peter Zijlstra (Intel) <[email protected]>
Signed-off-by: Ingo Molnar <[email protected]>
|
|
Currently, is_kdump_kernel() returns true when elfcorehdr_addr is set.
While elfcorehdr_addr is set for kexec based kernel dump mechanism,
alternate dump capturing methods like fadump [1] also set it to export
the vmcore. Since, is_kdump_kernel() is used to restrict resources in
crash dump capture kernel and such restrictions may not be desirable
for fadump, allow is_kdump_kernel() to be defined differently for such
scenarios. With this, is_kdump_kernel() could be false while vmcore is
usable. So, remove unnecessary dependency with is_kdump_kernel(), for
exporting vmcore.
[1] https://docs.kernel.org/powerpc/firmware-assisted-dump.html
Suggested-by: Michael Ellerman <[email protected]>
Signed-off-by: Hari Bathini <[email protected]>
Acked-by: Baoquan He <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://msgid.link/[email protected]
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Misc fixes:
- Fix an UV boot crash
- Skip spurious ENDBR generation on _THIS_IP_
- Fix ENDBR use in putuser() asm methods
- Fix corner case boot crashes on 5-level paging
- and fix a false positive WARNING on LTO kernels"
* tag 'x86-urgent-2023-09-17' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/purgatory: Remove LTO flags
x86/boot/compressed: Reserve more memory for page tables
x86/ibt: Avoid duplicate ENDBR in __put_user_nocheck*()
x86/ibt: Suppress spurious ENDBR
x86/platform/uv: Use alternate source for socket to node data
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"Regression and bug fixes for ext4"
* tag 'ext4_for_linus-6.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix rec_len verify error
ext4: do not let fstrim block system suspend
ext4: move setting of trimmed bit into ext4_try_to_trim_range()
jbd2: Fix memory leak in journal_init_common()
jbd2: Remove page size assumptions
buffer: Make bh_offset() work for compound pages
|
|
Alexei Starovoitov says:
====================
The following pull-request contains BPF updates for your *net-next* tree.
We've added 73 non-merge commits during the last 9 day(s) which contain
a total of 79 files changed, 5275 insertions(+), 600 deletions(-).
The main changes are:
1) Basic BTF validation in libbpf, from Andrii Nakryiko.
2) bpf_assert(), bpf_throw(), exceptions in bpf progs, from Kumar Kartikeya Dwivedi.
3) next_thread cleanups, from Oleg Nesterov.
4) Add mcpu=v4 support to arm32, from Puranjay Mohan.
5) Add support for __percpu pointers in bpf progs, from Yonghong Song.
6) Fix bpf tailcall interaction with bpf trampoline, from Leon Hwang.
7) Raise irq_work in bpf_mem_alloc while irqs are disabled to improve refill probabablity, from Hou Tao.
Please consider pulling these changes from:
git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next.git
Thanks a lot!
Also thanks to reporters, reviewers and testers of commits in this pull-request:
Alan Maguire, Andrey Konovalov, Dave Marchevsky, "Eric W. Biederman",
Jiri Olsa, Maciej Fijalkowski, Quentin Monnet, Russell King (Oracle),
Song Liu, Stanislav Fomichev, Yonghong Song
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
Benefit from the existence of internal mlx5 notifier and extend it by
event MLX5_DRIVER_EVENT_SF_PEER_DEVLINK. Use this event from SF
auxiliary device probe/remove functions to pass the registered SF
devlink instance to the SF representor.
Process the new event in SF representor code and call
devl_port_fn_devlink_set() to do the assignments. Implement this in work
to avoid possible deadlock when probe/remove function of SF may be
called with devlink instance lock held during devlink reload.
Signed-off-by: Jiri Pirko <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Implement SyncE support using newly introduced DPLL support.
Make sure that each PFs/VFs/SFs probed with appropriate capability
will spawn a dpll auxiliary device and register appropriate dpll device
and pin instances.
Signed-off-by: Jiri Pirko <[email protected]>
Signed-off-by: Arkadiusz Kubalewski <[email protected]>
Signed-off-by: Vadim Fedorenko <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
In case netdevice represents a SyncE port, the user needs to understand
the connection between netdevice and associated DPLL pin. There might me
multiple netdevices pointing to the same pin, in case of VF/SF
implementation.
Add a IFLA Netlink attribute to nest the DPLL pin handle, similar to
how it is implemented for devlink port. Add a struct dpll_pin pointer
to netdev and protect access to it by RTNL. Expose netdev_dpll_pin_set()
and netdev_dpll_pin_clear() helpers to the drivers so they can set/clear
the DPLL pin relationship to netdev.
Note that during the lifetime of struct dpll_pin the pin handle does not
change. Therefore it is save to access it lockless. It is drivers
responsibility to call netdev_dpll_pin_clear() before dpll_pin_put().
Signed-off-by: Jiri Pirko <[email protected]>
Signed-off-by: Arkadiusz Kubalewski <[email protected]>
Signed-off-by: Vadim Fedorenko <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
DPLL framework is used to represent and configure DPLL devices
in systems. Each device that has DPLL and can configure inputs
and outputs can use this framework.
Implement dpll netlink framework functions for enablement of dpll
subsystem netlink family.
Co-developed-by: Milena Olech <[email protected]>
Signed-off-by: Milena Olech <[email protected]>
Co-developed-by: Michal Michalik <[email protected]>
Signed-off-by: Michal Michalik <[email protected]>
Signed-off-by: Vadim Fedorenko <[email protected]>
Co-developed-by: Arkadiusz Kubalewski <[email protected]>
Signed-off-by: Arkadiusz Kubalewski <[email protected]>
Signed-off-by: Jiri Pirko <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
DPLL framework is used to represent and configure DPLL devices
in systems. Each device that has DPLL and can configure inputs
and outputs can use this framework.
Implement core framework functions for further interactions
with device drivers implementing dpll subsystem, as well as for
interactions of DPLL netlink framework part with the subsystem
itself.
Co-developed-by: Milena Olech <[email protected]>
Signed-off-by: Milena Olech <[email protected]>
Co-developed-by: Michal Michalik <[email protected]>
Signed-off-by: Michal Michalik <[email protected]>
Signed-off-by: Vadim Fedorenko <[email protected]>
Co-developed-by: Arkadiusz Kubalewski <[email protected]>
Signed-off-by: Arkadiusz Kubalewski <[email protected]>
Signed-off-by: Jiri Pirko <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
-queue
Tony Nguyen says:
====================
Support rx-fcs on/off for VFs
Ahmed Zaki says:
Allow the user to turn on/off the CRC/FCS stripping through ethtool. We
first add the CRC offload capability in the virtchannel, then the feature
is enabled in ice and iavf drivers.
We make sure that the netdev features are fixed such that CRC stripping
cannot be disabled if VLAN rx offload (VLAN strip) is enabled. Also, VLAN
stripping cannot be enabled unless CRC stripping is ON.
Testing was done using tcpdump to make sure that the CRC is included in
the frame after:
# ethtool -K <interface> rx-fcs on
and is not included when it is back "off". Also, ethtool should return an
error for the above command if "rx-vlan-offload" is already on and at least
one VLAN interface/filter exists on the VF.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
power_supply_notifier can be internal, since all users are going
through power_supply_reg_notifier()/power_supply_unreg_notifier().
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Sebastian Reichel <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"16 small(ish) fixes all in drivers.
The major fixes are in pm8001 (fixes MSI-X issue going back to its
origin), the qla2xxx endianness fix, which fixes a bug on big endian
and the lpfc ones which can cause an oops on module removal without
them"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: lpfc: Prevent use-after-free during rmmod with mapped NVMe rports
scsi: lpfc: Early return after marking final NLP_DROPPED flag in dev_loss_tmo
scsi: lpfc: Fix the NULL vs IS_ERR() bug for debugfs_create_file()
scsi: target: core: Fix target_cmd_counter leak
scsi: pm8001: Setup IRQs on resume
scsi: pm80xx: Avoid leaking tags when processing OPC_INB_SET_CONTROLLER_CONFIG command
scsi: pm80xx: Use phy-specific SAS address when sending PHY_START command
scsi: ufs: core: Poll HCS.UCRDY before issuing a UIC command
scsi: ufs: core: Move __ufshcd_send_uic_cmd() outside host_lock
scsi: qedf: Add synchronization between I/O completions and abort
scsi: target: Replace strlcpy() with strscpy()
scsi: qla2xxx: Fix NULL vs IS_ERR() bug for debugfs_create_dir()
scsi: qla2xxx: Use raw_smp_processor_id() instead of smp_processor_id()
scsi: qla2xxx: Correct endianness for rqstlen and rsplen
scsi: ppa: Fix accidentally reversed conditions for 16-bit and 32-bit EPP
scsi: megaraid_sas: Fix deadlock on firmware crashdump
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata
Pull ata fixes from Damien Le Moal:
- Fix link power management transitions to disallow unsupported states
(Niklas)
- A small string handling fix for the sata_mv driver (Christophe)
- Clear port pending interrupts before reset, as per AHCI
specifications (Szuying).
Followup fixes for this one are to not clear ATA_PFLAG_EH_PENDING in
ata_eh_reset() to allow EH to continue on with other actions recorded
with error interrupts triggered before EH completes. And an
additional fix to avoid thawing a port twice in EH (Niklas)
- Small code style fixes in the pata_parport driver to silence the
build bot as it keeps complaining about bad indentation (me)
- A fix for the recent CDL code to avoid fetching sense data for
successful commands when not necessary for correct operation (Niklas)
* tag 'ata-6.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata:
ata: libata-core: fetch sense data for successful commands iff CDL enabled
ata: libata-eh: do not thaw the port twice in ata_eh_reset()
ata: libata-eh: do not clear ATA_PFLAG_EH_PENDING in ata_eh_reset()
ata: pata_parport: Fix code style issues
ata: libahci: clear pending interrupt status
ata: sata_mv: Fix incorrect string length computation in mv_dump_mem()
ata: libata: disallow dev-initiated LPM transitions to unsupported states
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"The main thing is the removal of 'probe_new' because all i2c client
drivers are converted now. Thanks Uwe, this marks the end of a long
conversion process.
Other than that, we have a few Kconfig updates and driver bugfixes"
* tag 'i2c-for-6.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: cadence: Fix the kernel-doc warnings
i2c: aspeed: Reset the i2c controller when timeout occurs
i2c: I2C_MLXCPLD on ARM64 should depend on ACPI
i2c: Make I2C_ATR invisible
i2c: Drop legacy callback .probe_new()
w1: ds2482: Switch back to use struct i2c_driver's .probe()
|
|
We require access to this kasan helper in BPF code in the next patch
where we have to unpoison the task stack when we unwind and reset the
stack frame from bpf_throw, and it never really unpoisons the poisoned
stack slots on entry when compiler instrumentation is generated by
CONFIG_KASAN_STACK and inline instrumentation is supported.
Also, remove the declaration from mm/kasan/kasan.h as we put it in the
header file kasan.h.
Cc: Andrey Ryabinin <[email protected]>
Cc: Alexander Potapenko <[email protected]>
Cc: Andrey Konovalov <[email protected]>
Cc: Dmitry Vyukov <[email protected]>
Cc: Vincenzo Frascino <[email protected]>
Suggested-by: Andrey Konovalov <[email protected]>
Signed-off-by: Kumar Kartikeya Dwivedi <[email protected]>
Reviewed-by: Andrey Konovalov <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Alexei Starovoitov <[email protected]>
|
|
By default, the subprog generated by the verifier to handle a thrown
exception hardcodes a return value of 0. To allow user-defined logic
and modification of the return value when an exception is thrown,
introduce the 'exception_callback:' declaration tag, which marks a
callback as the default exception handler for the program.
The format of the declaration tag is 'exception_callback:<value>', where
<value> is the name of the exception callback. Each main program can be
tagged using this BTF declaratiion tag to associate it with an exception
callback. In case the tag is absent, the default callback is used.
As such, the exception callback cannot be modified at runtime, only set
during verification.
Allowing modification of the callback for the current program execution
at runtime leads to issues when the programs begin to nest, as any
per-CPU state maintaing this information will have to be saved and
restored. We don't want it to stay in bpf_prog_aux as this takes a
global effect for all programs. An alternative solution is spilling
the callback pointer at a known location on the program stack on entry,
and then passing this location to bpf_throw as a parameter.
However, since exceptions are geared more towards a use case where they
are ideally never invoked, optimizing for this use case and adding to
the complexity has diminishing returns.
Signed-off-by: Kumar Kartikeya Dwivedi <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Alexei Starovoitov <[email protected]>
|
|
This patch implements BPF exceptions, and introduces a bpf_throw kfunc
to allow programs to throw exceptions during their execution at runtime.
A bpf_throw invocation is treated as an immediate termination of the
program, returning back to its caller within the kernel, unwinding all
stack frames.
This allows the program to simplify its implementation, by testing for
runtime conditions which the verifier has no visibility into, and assert
that they are true. In case they are not, the program can simply throw
an exception from the other branch.
BPF exceptions are explicitly *NOT* an unlikely slowpath error handling
primitive, and this objective has guided design choices of the
implementation of the them within the kernel (with the bulk of the cost
for unwinding the stack offloaded to the bpf_throw kfunc).
The implementation of this mechanism requires use of add_hidden_subprog
mechanism introduced in the previous patch, which generates a couple of
instructions to move R1 to R0 and exit. The JIT then rewrites the
prologue of this subprog to take the stack pointer and frame pointer as
inputs and reset the stack frame, popping all callee-saved registers
saved by the main subprog. The bpf_throw function then walks the stack
at runtime, and invokes this exception subprog with the stack and frame
pointers as parameters.
Reviewers must take note that currently the main program is made to save
all callee-saved registers on x86_64 during entry into the program. This
is because we must do an equivalent of a lightweight context switch when
unwinding the stack, therefore we need the callee-saved registers of the
caller of the BPF program to be able to return with a sane state.
Note that we have to additionally handle r12, even though it is not used
by the program, because when throwing the exception the program makes an
entry into the kernel which could clobber r12 after saving it on the
stack. To be able to preserve the value we received on program entry, we
push r12 and restore it from the generated subprogram when unwinding the
stack.
For now, bpf_throw invocation fails when lingering resources or locks
exist in that path of the program. In a future followup, bpf_throw will
be extended to perform frame-by-frame unwinding to release lingering
resources for each stack frame, removing this limitation.
Signed-off-by: Kumar Kartikeya Dwivedi <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Alexei Starovoitov <[email protected]>
|
|
Introduce support in the verifier for generating a subprogram and
include it as part of a BPF program dynamically after the do_check phase
is complete. The first user will be the next patch which generates
default exception callbacks if none are set for the program. The phase
of invocation will be do_misc_fixups. Note that this is an internal
verifier function, and should be used with instruction blocks which
uphold the invariants stated in check_subprogs.
Since these subprogs are always appended to the end of the instruction
sequence of the program, it becomes relatively inexpensive to do the
related adjustments to the subprog_info of the program. Only the fake
exit subprogram is shifted forward, making room for our new subprog.
This is useful to insert a new subprogram, get it JITed, and obtain its
function pointer. The next patch will use this functionality to insert a
default exception callback which will be invoked after unwinding the
stack.
Note that these added subprograms are invisible to userspace, and never
reported in BPF_OBJ_GET_INFO_BY_ID etc. For now, only a single
subprogram is supported, but more can be easily supported in the future.
To this end, two function counts are introduced now, the existing
func_cnt, and real_func_cnt, the latter including hidden programs. This
allows us to conver the JIT code to use the real_func_cnt for management
of resources while syscall path continues working with existing
func_cnt.
Signed-off-by: Kumar Kartikeya Dwivedi <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Alexei Starovoitov <[email protected]>
|
|
The plumbing for offline unwinding when we throw an exception in
programs would require walking the stack, hence introduce a new
arch_bpf_stack_walk function. This is provided when the JIT supports
exceptions, i.e. bpf_jit_supports_exceptions is true. The arch-specific
code is really minimal, hence it should be straightforward to extend
this support to other architectures as well, as it reuses the logic of
arch_stack_walk, but allowing access to unwind_state data.
Once the stack pointer and frame pointer are known for the main subprog
during the unwinding, we know the stack layout and location of any
callee-saved registers which must be restored before we return back to
the kernel. This handling will be added in the subsequent patches.
Note that while we primarily unwind through BPF frames, which are
effectively CONFIG_UNWINDER_FRAME_POINTER, we still need one of this or
CONFIG_UNWINDER_ORC to be able to unwind through the bpf_throw frame
from which we begin walking the stack. We also require both sp and bp
(stack and frame pointers) from the unwind_state structure, which are
only available when one of these two options are enabled.
Signed-off-by: Kumar Kartikeya Dwivedi <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Alexei Starovoitov <[email protected]>
|
|
We would like to know whether a bpf_prog corresponds to the main prog or
one of the subprogs. The current JIT implementations simply check this
using the func_idx in bpf_prog->aux->func_idx. When the index is 0, it
belongs to the main program, otherwise it corresponds to some
subprogram.
This will also be necessary to halt exception propagation while walking
the stack when an exception is thrown, so we add a simple helper
function to check this, named bpf_is_subprog, and convert existing JIT
implementations to also make use of it.
Signed-off-by: Kumar Kartikeya Dwivedi <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Alexei Starovoitov <[email protected]>
|
|
The 2023 SIGCOMM paper "Improving Network Availability with Protective
ReRoute" has indicated Linux TCP's RTO-triggered txhash rehashing can
effectively reduce application disruption during outages. To better
measure the efficacy of this feature, this patch adds three more
detailed stats during RTO recovery and exports via TCP_INFO.
Applications and monitoring systems can leverage this data to measure
the network path diversity and end-to-end repair latency during network
outages to improve their network infrastructure.
The following counters are added to tcp_sock in order to track RTO
events over the lifetime of a TCP socket.
1. u16 total_rto - Counts the total number of RTO timeouts.
2. u16 total_rto_recoveries - Counts the total number of RTO recoveries.
3. u32 total_rto_time - Counts the total time spent (ms) in RTO
recoveries. (time spent in CA_Loss and
CA_Recovery states)
To compute total_rto_time, we add a new u32 rto_stamp field to
tcp_sock. rto_stamp records the start timestamp (ms) of the last RTO
recovery (CA_Loss).
Corresponding fields are also added to the tcp_info struct.
Signed-off-by: Aananth V <[email protected]>
Signed-off-by: Neal Cardwell <[email protected]>
Signed-off-by: Yuchung Cheng <[email protected]>
Reviewed-by: Eric Dumazet <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Alexei Starovoitov says:
====================
The following pull-request contains BPF updates for your *net* tree.
We've added 21 non-merge commits during the last 8 day(s) which contain
a total of 21 files changed, 450 insertions(+), 36 deletions(-).
The main changes are:
1) Adjust bpf_mem_alloc buckets to match ksize(), from Hou Tao.
2) Check whether override is allowed in kprobe mult, from Jiri Olsa.
3) Fix btf_id symbol generation with ld.lld, from Jiri and Nick.
4) Fix potential deadlock when using queue and stack maps from NMI, from Toke Høiland-Jørgensen.
Please consider pulling these changes from:
git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf.git
Thanks a lot!
Also thanks to reporters, reviewers and testers of commits in this pull-request:
Alan Maguire, Biju Das, Björn Töpel, Dan Carpenter, Daniel Borkmann,
Eduard Zingerman, Hsin-Wei Hung, Marcus Seyfarth, Nathan Chancellor,
Satya Durga Srinivasu Prabhala, Song Liu, Stephen Rothwell
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
The BPF JITs now support cpuv4 instructions. Add tests for these new
instructions to the test suite:
1. Sign extended Load
2. Sign extended Mov
3. Unconditional byte swap
4. Unconditional jump with 32-bit offset
5. Signed division and modulo
Signed-off-by: Puranjay Mohan <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Alexei Starovoitov <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull thermal control fixes from Rafael Wysocki:
"These fix a thermal core breakage introduced by one of the recent
changes, amend those changes by adding 'const' to a new callback
argument and fix two memory leaks.
Specifics:
- Unbreak disabled trip point check in handle_thermal_trip() that may
cause it to skip enabled trip points (Rafael Wysocki)
- Add missing of_node_put() to of_find_trip_id() and
thermal_of_for_each_cooling_maps() that each break out of a
for_each_child_of_node() loop without dropping the reference to the
child object (Julia Lawall)
- Constify the recently added trip argument of the .get_trend()
thermal zone callback (Rafael Wysocki)"
* tag 'thermal-6.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
thermal: core: Fix disabled trip point check in handle_thermal_trip()
thermal: Constify the trip argument of the .get_trend() zone callback
thermal/of: add missing of_node_put()
|
|
On 64-bit systems, the compiler will complain that the comparison
between SIZE_MAX and the 32-bit unsigned int 'len' is unnecessary.
Signed-off-by: Trond Myklebust <[email protected]>
Signed-off-by: Anna Schumaker <[email protected]>
|
|
This reverts commit e87cf8a28e7592bd19064e8181324ae26bc02932.
This commit was added to silence a tautological comparison warning, but
removing the 'len' value check before calling xdr_inline_decode() is
really not what we want.
Signed-off-by: Anna Schumaker <[email protected]>
|
|
Commit b2e2ba578e01 ("x86/vdso: Initialize the CPU/node NR segment
descriptor earlier") removed the single user of this constant.
Remove it to reduce the size of cpuhp_hp_states[].
Signed-off-by: Olaf Hering <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Marcus and Satya reported an issue where BTF_ID macro generates same
symbol in separate objects and that breaks final vmlinux link.
ld.lld: error: ld-temp.o <inline asm>:14577:1: symbol
'__BTF_ID__struct__cgroup__624' is already defined
This can be triggered under specific configs when __COUNTER__ happens to
be the same for the same symbol in two different translation units,
which is already quite unlikely to happen.
Add __LINE__ number suffix to make BTF_ID symbol more unique, which is
not a complete fix, but it would help for now and meanwhile we can work
on better solution as suggested by Andrii.
Cc: [email protected]
Reported-by: Satya Durga Srinivasu Prabhala <[email protected]>
Reported-by: Marcus Seyfarth <[email protected]>
Closes: https://github.com/ClangBuiltLinux/linux/issues/1913
Debugged-by: Nathan Chancellor <[email protected]>
Link: https://lore.kernel.org/bpf/CAEf4Bzb5KQ2_LmhN769ifMeSJaWfebccUasQOfQKaOd0nQ51tw@mail.gmail.com/
Signed-off-by: Jiri Olsa <[email protected]>
Signed-off-by: Nick Desaulniers <[email protected]>
Reviewed-by: Nathan Chancellor <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Alexei Starovoitov <[email protected]>
|
|
When CONFIG_NUMA is enabled, sched_numa_find_nth_cpu() searches for a
CPU in sched_domains_numa_masks. The masks includes only online CPUs,
so effectively offline CPUs are skipped.
When CONFIG_NUMA is disabled, the fallback function should be consistent.
Fixes: cd7f55359c90 ("sched: add sched_numa_find_nth_cpu()")
Signed-off-by: Yury Norov <[email protected]>
Signed-off-by: Ingo Molnar <[email protected]>
Cc: Mel Gorman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|