| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
On the Turris Mox router different modules can be connected to the main
CPU board: currently a module with a SFP cage, a module with MiniPCIe
connector, a PCIe pass-through MiniPCIe connector module, a 4-port
switch module, an 8-port switch module, and a 4-port USB3 module.
For example:
[CPU]-[PCIe-pass-through]-[PCIe]-[8-port switch]-[8-port switch]-[SFP]
Each of this modules has an input and output shift register, and these
are connected via SPI to the CPU board.
Via SPI we are able to discover which modules are connected, in which
order, and we can also read some information about the modules (eg.
their interrupt status), and configure them.
From each module 8 bits can be read (of which low 4 bits identify the
module) and 8 bits can be written.
For example from the module with a SFP cage we can read the LOS,
TX-FAULT and MOD-DEF0 signals, while we can write TX-DISABLE and
RATE-SELECT signals.
This driver creates a new bus type, called "moxtet". For each Mox module
it finds via SPI, it creates a new device on the moxtet bus so that
drivers can be written for them.
It also implements a virtual interrupt controller for the modules which
send their interrupt status over the SPI shift register. These modules
do this in addition to sending their interrupt status via the shared
interrupt line. When the shared interrupt is triggered, we read from the
shift register and handle IRQs for all devices which are in interrupt.
The topology of how Mox modules are connected can then be read by
listing /sys/bus/moxtet/devices.
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Linus Walleij <[email protected]>
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
In the general move to have i2c_new_*_device functions which return
ERR_PTR instead of NULL, this patch converts i2c_new_secondary_device().
There are only few users, so this patch converts the I2C core and all
users in one go. The function gets renamed to i2c_new_ancillary_device()
so out-of-tree users will get a build failure to understand they need to
adapt their error checking code.
Signed-off-by: Wolfram Sang <[email protected]>
Reviewed-by: Kieran Bingham <[email protected]> # adv748x
Reviewed-by: Laurent Pinchart <[email protected]> # adv7511 + adv7604
Reviewed-by: Hans Verkuil <[email protected]> # adv7604
Signed-off-by: Wolfram Sang <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux into for-next/cpu-topology
Pull in generic CPU topology changes from Paul Walmsley (RISC-V).
* tag 'common/for-v5.4-rc1/cpu-topology' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
MAINTAINERS: Add an entry for generic architecture topology
base: arch_topology: update Kconfig help description
RISC-V: Parse cpu topology during boot.
arm: Use common cpu_topology structure and functions.
cpu-topology: Move cpu topology code to common code.
dt-binding: cpu-topology: Move cpu-map to a common binding.
Documentation: DT: arm: add support for sockets defining package boundaries
|
|
when do randbuilding, I got this error:
In file included from drivers/hwmon/pmbus/ucd9000.c:19:0:
./include/linux/gpio/driver.h:576:1: error: redefinition of gpiochip_add_pin_range
gpiochip_add_pin_range(struct gpio_chip *chip, const char *pinctl_name,
^~~~~~~~~~~~~~~~~~~~~~
In file included from drivers/hwmon/pmbus/ucd9000.c:18:0:
./include/linux/gpio.h:245:1: note: previous definition of gpiochip_add_pin_range was here
gpiochip_add_pin_range(struct gpio_chip *chip, const char *pinctl_name,
^~~~~~~~~~~~~~~~~~~~~~
Reported-by: Hulk Robot <[email protected]>
Fixes: 964cb341882f ("gpio: move pincontrol calls to <linux/gpio/driver.h>")
Signed-off-by: YueHaibing <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Linus Walleij <[email protected]>
|
|
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for net-next:
1) Rename mss field to mss_option field in synproxy, from Fernando Mancera.
2) Use SYSCTL_{ZERO,ONE} definitions in conntrack, from Matteo Croce.
3) More strict validation of IPVS sysctl values, from Junwei Hu.
4) Remove unnecessary spaces after on the right hand side of assignments,
from yangxingwu.
5) Add offload support for bitwise operation.
6) Extend the nft_offload_reg structure to store immediate date.
7) Collapse several ip_set header files into ip_set.h, from
Jeremy Sowden.
8) Make netfilter headers compile with CONFIG_KERNEL_HEADER_TEST=y,
from Jeremy Sowden.
9) Fix several sparse warnings due to missing prototypes, from
Valdis Kletnieks.
10) Use static lock initialiser to ensure connlabel spinlock is
initialized on boot time to fix sched/act_ct.c, patch
from Florian Westphal.
====================
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
So far phy_speed_down/up can be used up to 1Gbps only. Remove this
restriction by using new helper __phy_speed_down. New member adv_old
in struct phy_device is used by phy_speed_up to restore the advertised
modes before calling phy_speed_down. Don't simply advertise what is
supported because a user may have intentionally removed modes from
advertisement.
Signed-off-by: Heiner Kallweit <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
phy_speed_down_core provides most of the functionality for
phy_speed_down. It makes use of new helper phy_resolve_min_speed that is
based on the sorting of the settings[] array. In certain cases it may be
helpful to be able to exclude legacy half duplex modes, therefore
prepare phy_resolve_min_speed() for it.
v2:
- rename __phy_speed_down to phy_speed_down_core
Signed-off-by: Heiner Kallweit <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Daniel Borkmann says:
====================
The following pull-request contains BPF updates for your *net-next* tree.
There is a small merge conflict in libbpf (Cc Andrii so he's in the loop
as well):
for (i = 1; i <= btf__get_nr_types(btf); i++) {
t = (struct btf_type *)btf__type_by_id(btf, i);
if (!has_datasec && btf_is_var(t)) {
/* replace VAR with INT */
t->info = BTF_INFO_ENC(BTF_KIND_INT, 0, 0);
<<<<<<< HEAD
/*
* using size = 1 is the safest choice, 4 will be too
* big and cause kernel BTF validation failure if
* original variable took less than 4 bytes
*/
t->size = 1;
*(int *)(t+1) = BTF_INT_ENC(0, 0, 8);
} else if (!has_datasec && kind == BTF_KIND_DATASEC) {
=======
t->size = sizeof(int);
*(int *)(t + 1) = BTF_INT_ENC(0, 0, 32);
} else if (!has_datasec && btf_is_datasec(t)) {
>>>>>>> 72ef80b5ee131e96172f19e74b4f98fa3404efe8
/* replace DATASEC with STRUCT */
Conflict is between the two commits 1d4126c4e119 ("libbpf: sanitize VAR to
conservative 1-byte INT") and b03bc6853c0e ("libbpf: convert libbpf code to
use new btf helpers"), so we need to pick the sanitation fixup as well as
use the new btf_is_datasec() helper and the whitespace cleanup. Looks like
the following:
[...]
if (!has_datasec && btf_is_var(t)) {
/* replace VAR with INT */
t->info = BTF_INFO_ENC(BTF_KIND_INT, 0, 0);
/*
* using size = 1 is the safest choice, 4 will be too
* big and cause kernel BTF validation failure if
* original variable took less than 4 bytes
*/
t->size = 1;
*(int *)(t + 1) = BTF_INT_ENC(0, 0, 8);
} else if (!has_datasec && btf_is_datasec(t)) {
/* replace DATASEC with STRUCT */
[...]
The main changes are:
1) Addition of core parts of compile once - run everywhere (co-re) effort,
that is, relocation of fields offsets in libbpf as well as exposure of
kernel's own BTF via sysfs and loading through libbpf, from Andrii.
More info on co-re: http://vger.kernel.org/bpfconf2019.html#session-2
and http://vger.kernel.org/lpc-bpf2018.html#session-2
2) Enable passing input flags to the BPF flow dissector to customize parsing
and allowing it to stop early similar to the C based one, from Stanislav.
3) Add a BPF helper function that allows generating SYN cookies from XDP and
tc BPF, from Petar.
4) Add devmap hash-based map type for more flexibility in device lookup for
redirects, from Toke.
5) Improvements to XDP forwarding sample code now utilizing recently enabled
devmap lookups, from Jesper.
6) Add support for reporting the effective cgroup progs in bpftool, from Jakub
and Takshak.
7) Fix reading kernel config from bpftool via /proc/config.gz, from Peter.
8) Fix AF_XDP umem pages mapping for 32 bit architectures, from Ivan.
9) Follow-up to add two more BPF loop tests for the selftest suite, from Alexei.
10) Add perf event output helper also for other skb-based program types, from Allan.
11) Fix a co-re related compilation error in selftests, from Yonghong.
====================
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
This reverts commit 2f0799a0ffc033b ("mm, thp: restore node-local
hugepage allocations").
commit 2f0799a0ffc033b was rightfully applied to avoid the risk of a
severe regression that was reported by the kernel test robot at the end
of the merge window. Now we understood the regression was a false
positive and was caused by a significant increase in fairness during a
swap trashing benchmark. So it's safe to re-apply the fix and continue
improving the code from there. The benchmark that reported the
regression is very useful, but it provides a meaningful result only when
there is no significant alteration in fairness during the workload. The
removal of __GFP_THISNODE increased fairness.
__GFP_THISNODE cannot be used in the generic page faults path for new
memory allocations under the MPOL_DEFAULT mempolicy, or the allocation
behavior significantly deviates from what the MPOL_DEFAULT semantics are
supposed to be for THP and 4k allocations alike.
Setting THP defrag to "always" or using MADV_HUGEPAGE (with THP defrag
set to "madvise") has never meant to provide an implicit MPOL_BIND on
the "current" node the task is running on, causing swap storms and
providing a much more aggressive behavior than even zone_reclaim_node =
3.
Any workload who could have benefited from __GFP_THISNODE has now to
enable zone_reclaim_mode=1||2||3. __GFP_THISNODE implicitly provided
the zone_reclaim_mode behavior, but it only did so if THP was enabled:
if THP was disabled, there would have been no chance to get any 4k page
from the current node if the current node was full of pagecache, which
further shows how this __GFP_THISNODE was misplaced in MADV_HUGEPAGE.
MADV_HUGEPAGE has never been intended to provide any zone_reclaim_mode
semantics, in fact the two are orthogonal, zone_reclaim_mode = 1|2|3
must work exactly the same with MADV_HUGEPAGE set or not.
The performance characteristic of memory depends on the hardware
details. The numbers below are obtained on Naples/EPYC architecture and
the N/A projection extends them to show what we should aim for in the
future as a good THP NUMA locality default. The benchmark used
exercises random memory seeks (note: the cost of the page faults is not
part of the measurement).
D0 THP | D0 4k | D1 THP | D1 4k | D2 THP | D2 4k | D3 THP | D3 4k | ...
0% | +43% | +45% | +106% | +131% | +224% | N/A | N/A
D0 means distance zero (i.e. local memory), D1 means distance one (i.e.
intra socket memory), D2 means distance two (i.e. inter socket memory),
etc...
For the guest physical memory allocated by qemu and for guest mode
kernel the performance characteristic of RAM is more complex and an
ideal default could be:
D0 THP | D1 THP | D0 4k | D2 THP | D1 4k | D3 THP | D2 4k | D3 4k | ...
0% | +58% | +101% | N/A | +222% | N/A | N/A | N/A
NOTE: the N/A are projections and haven't been measured yet, the
measurement in this case is done on a 1950x with only two NUMA nodes.
The THP case here means THP was used both in the host and in the guest.
After applying this commit the THP NUMA locality order that we'll get
out of MADV_HUGEPAGE is this:
D0 THP | D1 THP | D2 THP | D3 THP | ... | D0 4k | D1 4k | D2 4k | D3 4k | ...
Before this commit it was:
D0 THP | D0 4k | D1 4k | D2 4k | D3 4k | ...
Even if we ignore the breakage of large workloads that can't fit in a
single node that the __GFP_THISNODE implicit "current node" mbind
caused, the THP NUMA locality order provided by __GFP_THISNODE was still
not the one we shall aim for in the long term (i.e. the first one at
the top).
After this commit is applied, we can introduce a new allocator multi
order API and to replace those two alloc_pages_vmas calls in the page
fault path, with a single multi order call:
unsigned int order = (1 << HPAGE_PMD_ORDER) | (1 << 0);
page = alloc_pages_multi_order(..., &order);
if (!page)
goto out;
if (!(order & (1 << 0))) {
VM_WARN_ON(order != 1 << HPAGE_PMD_ORDER);
/* THP fault */
} else {
VM_WARN_ON(order != 1 << 0);
/* 4k fallback */
}
The page allocator logic has to be altered so that when it fails on any
zone with order 9, it has to try again with a order 0 before falling
back to the next zone in the zonelist.
After that we need to do more measurements and evaluate if adding an
opt-in feature for guest mode is worth it, to swap "DN 4k | DN+1 THP"
with "DN+1 THP | DN 4k" at every NUMA distance crossing.
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Andrea Arcangeli <[email protected]>
Acked-by: Michal Hocko <[email protected]>
Acked-by: Mel Gorman <[email protected]>
Cc: Vlastimil Babka <[email protected]>
Cc: David Rientjes <[email protected]>
Cc: Zi Yan <[email protected]>
Cc: Stefan Priebe - Profihost AG <[email protected]>
Cc: "Kirill A. Shutemov" <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
alloc_hugepage_direct_gfpmask""
Patch series "reapply: relax __GFP_THISNODE for MADV_HUGEPAGE mappings".
The fixes for what was originally reported as "pathological THP
behavior" we rightfully reverted to be sure not to introduced
regressions at end of a merge window after a severe regression report
from the kernel bot. We can safely re-apply them now that we had time
to analyze the problem.
The mm process worked fine, because the good fixes were eventually
committed upstream without excessive delay.
The regression reported by the kernel bot however forced us to revert
the good fixes to be sure not to introduce regressions and to give us
the time to analyze the issue further. The silver lining is that this
extra time allowed to think more at this issue and also plan for a
future direction to improve things further in terms of THP NUMA
locality.
This patch (of 2):
This reverts commit 356ff8a9a78fb35d ("Revert "mm, thp: consolidate THP
gfp handling into alloc_hugepage_direct_gfpmask"). So it reapplies
89c83fb539f954 ("mm, thp: consolidate THP gfp handling into
alloc_hugepage_direct_gfpmask").
Consolidation of the THP allocation flags at the same place was meant to
be a clean up to easier handle otherwise scattered code which is
imposing a maintenance burden. There were no real problems observed
with the gfp mask consolidation but the reversion was rushed through
without a larger consensus regardless.
This patch brings the consolidation back because this should make the
long term maintainability easier as well as it should allow future
changes to be less error prone.
[[email protected]: changelog additions]
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Andrea Arcangeli <[email protected]>
Acked-by: Michal Hocko <[email protected]>
Cc: Mel Gorman <[email protected]>
Cc: Vlastimil Babka <[email protected]>
Cc: David Rientjes <[email protected]>
Cc: Zi Yan <[email protected]>
Cc: Stefan Priebe - Profihost AG <[email protected]>
Cc: "Kirill A. Shutemov" <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Memcg counters for shadow nodes are broken because the memcg pointer is
obtained in a wrong way. The following approach is used:
virt_to_page(xa_node)->mem_cgroup
Since commit 4d96ba353075 ("mm: memcg/slab: stop setting
page->mem_cgroup pointer for slab pages") page->mem_cgroup pointer isn't
set for slab pages, so memcg_from_slab_page() should be used instead.
Also I doubt that it ever worked correctly: virt_to_head_page() should
be used instead of virt_to_page(). Otherwise objects residing on tail
pages are not accounted, because only the head page contains a valid
mem_cgroup pointer. That was a case since the introduction of these
counters by the commit 68d48e6a2df5 ("mm: workingset: add vmstat counter
for shadow nodes").
Link: http://lkml.kernel.org/r/[email protected]
Fixes: 4d96ba353075 ("mm: memcg/slab: stop setting page->mem_cgroup pointer for slab pages")
Signed-off-by: Roman Gushchin <[email protected]>
Acked-by: Johannes Weiner <[email protected]>
Cc: Vladimir Davydov <[email protected]>
Cc: Shakeel Butt <[email protected]>
Cc: Michal Hocko <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Patch series "mm/hmm: fixes for device private page migration", v3.
Testing the latest linux git tree turned up a few bugs with page
migration to and from ZONE_DEVICE private and anonymous pages.
Hopefully it clarifies how ZONE_DEVICE private struct page uses the same
mapping and index fields from the source anonymous page mapping.
This patch (of 3):
Struct page for ZONE_DEVICE private pages uses the page->mapping and and
page->index fields while the source anonymous pages are migrated to
device private memory. This is so rmap_walk() can find the page when
migrating the ZONE_DEVICE private page back to system memory.
ZONE_DEVICE pmem backed fsdax pages also use the page->mapping and
page->index fields when files are mapped into a process address space.
Add comments to struct page and remove the unused "_zd_pad_1" field to
make this more clear.
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Ralph Campbell <[email protected]>
Reviewed-by: John Hubbard <[email protected]>
Cc: Matthew Wilcox <[email protected]>
Cc: Vlastimil Babka <[email protected]>
Cc: Christoph Lameter <[email protected]>
Cc: Dave Hansen <[email protected]>
Cc: Jérôme Glisse <[email protected]>
Cc: "Kirill A . Shutemov" <[email protected]>
Cc: Lai Jiangshan <[email protected]>
Cc: Martin Schwidefsky <[email protected]>
Cc: Pekka Enberg <[email protected]>
Cc: Randy Dunlap <[email protected]>
Cc: Andrey Ryabinin <[email protected]>
Cc: Christoph Hellwig <[email protected]>
Cc: Jason Gunthorpe <[email protected]>
Cc: Andrew Morton <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Upcoming ->nocb_lock contention-reduction work requires that the
rcu_segcblist structure's ->len field be concurrently manipulated,
but only if there are no-CBs CPUs in the kernel. This commit
therefore makes this ->len field be an atomic_long_t, but only
in CONFIG_RCU_NOCB_CPU=y kernels.
Signed-off-by: Paul E. McKenney <[email protected]>
|
|
RCU callback processing currently uses rcu_is_nocb_cpu() to determine
whether or not the current CPU's callbacks are to be offloaded.
This works, but it is not so good for cache locality. Plus use of
->cblist for offloaded callbacks will greatly increase the frequency
of these checks. This commit therefore adds a ->offloaded flag to the
rcu_segcblist structure to provide a more flexible and cache-friendly
means of checking for callback offloading.
Signed-off-by: Paul E. McKenney <[email protected]>
|
|
NULLing the RCU_NEXT_TAIL pointer was a clever way to save a byte, but
forward-progress considerations would require that this pointer be both
NULL and non-NULL, which, absent a quantum-computer port of the Linux
kernel, simply won't happen. This commit therefore creates as separate
->enabled flag to replace the current NULL checks.
[ paulmck: Add include files per 0day test robot and -next. ]
Signed-off-by: Paul E. McKenney <[email protected]>
|
|
Introduce an optional callback in interconnect provider drivers. It can be
used for implementing actions, that need to be executed before the actual
aggregation of the bandwidth requests has started.
The benefit of this for now is that it will significantly simplify the code
in provider drivers.
Suggested-by: Evan Green <[email protected]>
Reviewed-by: Evan Green <[email protected]>
Signed-off-by: Georgi Djakov <[email protected]>
|
|
Consumers may have use cases with different bandwidth requirements based
on the system or driver state. The consumer driver can append a specific
tag to the path and pass this information to the interconnect platform
driver to do the aggregation based on this state.
Introduce icc_set_tag() function that will allow the consumers to append
an optional tag to each path. The aggregation of these tagged paths is
platform specific.
Reviewed-by: Evan Green <[email protected]>
Signed-off-by: Georgi Djakov <[email protected]>
|
|
Add two events that were defined in the device specification but were
not exposed in the driver list.
Post this patch those events can be read over the DEVX events interface
once be reported by the firmware.
Signed-off-by: Yishai Hadas <[email protected]>
Reviewed-by: Edward Srouji <[email protected]>
Signed-off-by: Leon Romanovsky <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Doug Ledford <[email protected]>
|
|
Merging tip of mlx5-next in order to get changes related to adding
XRQ support to the DEVX interface needed prior to the following two
patches.
Signed-off-by: Doug Ledford <[email protected]>
|
|
Update the build scripts and the version magic to reflect when
CONFIG_PREEMPT_RT is enabled in the same way as CONFIG_PREEMPT is treated.
The resulting version strings:
Linux m 5.3.0-rc1+ #100 SMP Fri Jul 26 ...
Linux m 5.3.0-rc1+ #101 SMP PREEMPT Fri Jul 26 ...
Linux m 5.3.0-rc1+ #102 SMP PREEMPT_RT Fri Jul 26 ...
The module vermagic:
5.3.0-rc1+ SMP mod_unload modversions
5.3.0-rc1+ SMP preempt mod_unload modversions
5.3.0-rc1+ SMP preempt_rt mod_unload modversions
Signed-off-by: Thomas Gleixner <[email protected]>
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
A few fields in various structures is missing the corresponding
kerneldoc comments. Add them. Also, fixed the comment for sidlemodes.
Signed-off-by: Suman Anna <[email protected]>
Acked-by: Roger Quadros <[email protected]>
Signed-off-by: Tony Lindgren <[email protected]>
|
|
Use the appropriate SPDX license identifier in the TI sysc
interconnect target driver source files and drop the previous
boilerplate license text. Also, add the the SPDX license
identifier in the associated ti-sysc header files.
Signed-off-by: Suman Anna <[email protected]>
Acked-by: Roger Quadros <[email protected]>
Signed-off-by: Tony Lindgren <[email protected]>
|
|
A number of non-UAPI Netfilter header-files contained superfluous
"#ifdef __KERNEL__" guards. Removed them.
Signed-off-by: Jeremy Sowden <[email protected]>
Signed-off-by: Pablo Neira Ayuso <[email protected]>
|
|
linux/netfilter.h defines a number of struct and inline function
definitions which are only available is CONFIG_NETFILTER is enabled.
These structs and functions are used in declarations and definitions in
other header-files. Added preprocessor checks to make sure these
headers will compile if CONFIG_NETFILTER is disabled.
Signed-off-by: Jeremy Sowden <[email protected]>
Signed-off-by: Pablo Neira Ayuso <[email protected]>
|
|
A number of netfilter header-files used declarations and definitions
from other headers without including them. Added include directives to
make those declarations and definitions available.
Signed-off-by: Jeremy Sowden <[email protected]>
Signed-off-by: Pablo Neira Ayuso <[email protected]>
|
|
linux/netfilter/ipset/ip_set.h included four other header files:
include/linux/netfilter/ipset/ip_set_comment.h
include/linux/netfilter/ipset/ip_set_counter.h
include/linux/netfilter/ipset/ip_set_skbinfo.h
include/linux/netfilter/ipset/ip_set_timeout.h
Of these the first three were not included anywhere else. The last,
ip_set_timeout.h, was included in a couple of other places, but defined
inline functions which call other inline functions defined in ip_set.h,
so ip_set.h had to be included before it.
Inlined all four into ip_set.h, and updated the other files that
included ip_set_timeout.h.
Signed-off-by: Jeremy Sowden <[email protected]>
Acked-by: Jozsef Kadlecsik <[email protected]>
Signed-off-by: Pablo Neira Ayuso <[email protected]>
|
|
Add XRQ legacy commands opcodes, will be used via the DEVX interface.
Signed-off-by: Yishai Hadas <[email protected]>
Reviewed-by: Saeed Mahameed <[email protected]>
Signed-off-by: Leon Romanovsky <[email protected]>
|
|
Be more consistent with the naming of the other DMA-buf objects.
Signed-off-by: Christian König <[email protected]>
Reviewed-by: Chris Wilson <[email protected]>
Link: https://patchwork.freedesktop.org/patch/323401/
|
|
The only remaining use for this is to protect against setting a new exclusive
fence while we grab both exclusive and shared. That can also be archived by
looking if the exclusive fence has changed or not after completing the
operation.
v2: switch setting excl fence to rcu_assign_pointer
Signed-off-by: Christian König <[email protected]>
Reviewed-by: Chris Wilson <[email protected]>
Link: https://patchwork.freedesktop.org/patch/322380/
|
|
Add a function to unregister a logical PIO range.
Logical PIO space can still be leaked when unregistering certain
LOGIC_PIO_CPU_MMIO regions, but this acceptable for now since there are no
callers to unregister LOGIC_PIO_CPU_MMIO regions, and the logical PIO
region allocation scheme would need significant work to improve this.
Cc: [email protected]
Signed-off-by: John Garry <[email protected]>
Signed-off-by: Wei Xu <[email protected]>
|
|
Add a function for filesystems to call to implement the
FS_IOC_MEASURE_VERITY ioctl. This ioctl retrieves the file measurement
that fs-verity calculated for the given file and is enforcing for reads;
i.e., reads that don't match this hash will fail. This ioctl can be
used for authentication or logging of file measurements in userspace.
See the "FS_IOC_MEASURE_VERITY" section of
Documentation/filesystems/fsverity.rst for the documentation.
Reviewed-by: Theodore Ts'o <[email protected]>
Reviewed-by: Jaegeuk Kim <[email protected]>
Signed-off-by: Eric Biggers <[email protected]>
|
|
Add a function for filesystems to call to implement the
FS_IOC_ENABLE_VERITY ioctl. This ioctl enables fs-verity on a file.
See the "FS_IOC_ENABLE_VERITY" section of
Documentation/filesystems/fsverity.rst for the documentation.
Reviewed-by: Theodore Ts'o <[email protected]>
Reviewed-by: Jaegeuk Kim <[email protected]>
Signed-off-by: Eric Biggers <[email protected]>
|
|
Add a root-only variant of the FS_IOC_REMOVE_ENCRYPTION_KEY ioctl which
removes all users' claims of the key, not just the current user's claim.
I.e., it always removes the key itself, no matter how many users have
added it.
This is useful for forcing a directory to be locked, without having to
figure out which user ID(s) the key was added under. This is planned to
be used by a command like 'sudo fscrypt lock DIR --all-users' in the
fscrypt userspace tool (http://github.com/google/fscrypt).
Reviewed-by: Theodore Ts'o <[email protected]>
Signed-off-by: Eric Biggers <[email protected]>
|
|
Add a new fscrypt policy version, "v2". It has the following changes
from the original policy version, which we call "v1" (*):
- Master keys (the user-provided encryption keys) are only ever used as
input to HKDF-SHA512. This is more flexible and less error-prone, and
it avoids the quirks and limitations of the AES-128-ECB based KDF.
Three classes of cryptographically isolated subkeys are defined:
- Per-file keys, like used in v1 policies except for the new KDF.
- Per-mode keys. These implement the semantics of the DIRECT_KEY
flag, which for v1 policies made the master key be used directly.
These are also planned to be used for inline encryption when
support for it is added.
- Key identifiers (see below).
- Each master key is identified by a 16-byte master_key_identifier,
which is derived from the key itself using HKDF-SHA512. This prevents
users from associating the wrong key with an encrypted file or
directory. This was easily possible with v1 policies, which
identified the key by an arbitrary 8-byte master_key_descriptor.
- The key must be provided in the filesystem-level keyring, not in a
process-subscribed keyring.
The following UAPI additions are made:
- The existing ioctl FS_IOC_SET_ENCRYPTION_POLICY can now be passed a
fscrypt_policy_v2 to set a v2 encryption policy. It's disambiguated
from fscrypt_policy/fscrypt_policy_v1 by the version code prefix.
- A new ioctl FS_IOC_GET_ENCRYPTION_POLICY_EX is added. It allows
getting the v1 or v2 encryption policy of an encrypted file or
directory. The existing FS_IOC_GET_ENCRYPTION_POLICY ioctl could not
be used because it did not have a way for userspace to indicate which
policy structure is expected. The new ioctl includes a size field, so
it is extensible to future fscrypt policy versions.
- The ioctls FS_IOC_ADD_ENCRYPTION_KEY, FS_IOC_REMOVE_ENCRYPTION_KEY,
and FS_IOC_GET_ENCRYPTION_KEY_STATUS now support managing keys for v2
encryption policies. Such keys are kept logically separate from keys
for v1 encryption policies, and are identified by 'identifier' rather
than by 'descriptor'. The 'identifier' need not be provided when
adding a key, since the kernel will calculate it anyway.
This patch temporarily keeps adding/removing v2 policy keys behind the
same permission check done for adding/removing v1 policy keys:
capable(CAP_SYS_ADMIN). However, the next patch will carefully take
advantage of the cryptographically secure master_key_identifier to allow
non-root users to add/remove v2 policy keys, thus providing a full
replacement for v1 policies.
(*) Actually, in the API fscrypt_policy::version is 0 while on-disk
fscrypt_context::format is 1. But I believe it makes the most sense
to advance both to '2' to have them be in sync, and to consider the
numbering to start at 1 except for the API quirk.
Reviewed-by: Paul Crowley <[email protected]>
Reviewed-by: Theodore Ts'o <[email protected]>
Signed-off-by: Eric Biggers <[email protected]>
|
|
Add a new fscrypt ioctl, FS_IOC_GET_ENCRYPTION_KEY_STATUS. Given a key
specified by 'struct fscrypt_key_specifier' (the same way a key is
specified for the other fscrypt key management ioctls), it returns
status information in a 'struct fscrypt_get_key_status_arg'.
The main motivation for this is that applications need to be able to
check whether an encrypted directory is "unlocked" or not, so that they
can add the key if it is not, and avoid adding the key (which may
involve prompting the user for a passphrase) if it already is.
It's possible to use some workarounds such as checking whether opening a
regular file fails with ENOKEY, or checking whether the filenames "look
like gibberish" or not. However, no workaround is usable in all cases.
Like the other key management ioctls, the keyrings syscalls may seem at
first to be a good fit for this. Unfortunately, they are not. Even if
we exposed the keyring ID of the ->s_master_keys keyring and gave
everyone Search permission on it (note: currently the keyrings
permission system would also allow everyone to "invalidate" the keyring
too), the fscrypt keys have an additional state that doesn't map cleanly
to the keyrings API: the secret can be removed, but we can be still
tracking the files that were using the key, and the removal can be
re-attempted or the secret added again.
After later patches, some applications will also need a way to determine
whether a key was added by the current user vs. by some other user.
Reserved fields are included in fscrypt_get_key_status_arg for this and
other future extensions.
Reviewed-by: Theodore Ts'o <[email protected]>
Signed-off-by: Eric Biggers <[email protected]>
|
|
Add a new fscrypt ioctl, FS_IOC_REMOVE_ENCRYPTION_KEY. This ioctl
removes an encryption key that was added by FS_IOC_ADD_ENCRYPTION_KEY.
It wipes the secret key itself, then "locks" the encrypted files and
directories that had been unlocked using that key -- implemented by
evicting the relevant dentries and inodes from the VFS caches.
The problem this solves is that many fscrypt users want the ability to
remove encryption keys, causing the corresponding encrypted directories
to appear "locked" (presented in ciphertext form) again. Moreover,
users want removing an encryption key to *really* remove it, in the
sense that the removed keys cannot be recovered even if kernel memory is
compromised, e.g. by the exploit of a kernel security vulnerability or
by a physical attack. This is desirable after a user logs out of the
system, for example. In many cases users even already assume this to be
the case and are surprised to hear when it's not.
It is not sufficient to simply unlink the master key from the keyring
(or to revoke or invalidate it), since the actual encryption transform
objects are still pinned in memory by their inodes. Therefore, to
really remove a key we must also evict the relevant inodes.
Currently one workaround is to run 'sync && echo 2 >
/proc/sys/vm/drop_caches'. But, that evicts all unused inodes in the
system rather than just the inodes associated with the key being
removed, causing severe performance problems. Moreover, it requires
root privileges, so regular users can't "lock" their encrypted files.
Another workaround, used in Chromium OS kernels, is to add a new
VFS-level ioctl FS_IOC_DROP_CACHE which is a more restricted version of
drop_caches that operates on a single super_block. It does:
shrink_dcache_sb(sb);
invalidate_inodes(sb, false);
But it's still a hack. Yet, the major users of filesystem encryption
want this feature badly enough that they are actually using these hacks.
To properly solve the problem, start maintaining a list of the inodes
which have been "unlocked" using each master key. Originally this
wasn't possible because the kernel didn't keep track of in-use master
keys at all. But, with the ->s_master_keys keyring it is now possible.
Then, add an ioctl FS_IOC_REMOVE_ENCRYPTION_KEY. It finds the specified
master key in ->s_master_keys, then wipes the secret key itself, which
prevents any additional inodes from being unlocked with the key. Then,
it syncs the filesystem and evicts the inodes in the key's list. The
normal inode eviction code will free and wipe the per-file keys (in
->i_crypt_info). Note that freeing ->i_crypt_info without evicting the
inodes was also considered, but would have been racy.
Some inodes may still be in use when a master key is removed, and we
can't simply revoke random file descriptors, mmap's, etc. Thus, the
ioctl simply skips in-use inodes, and returns -EBUSY to indicate that
some inodes weren't evicted. The master key *secret* is still removed,
but the fscrypt_master_key struct remains to keep track of the remaining
inodes. Userspace can then retry the ioctl to evict the remaining
inodes. Alternatively, if userspace adds the key again, the refreshed
secret will be associated with the existing list of inodes so they
remain correctly tracked for future key removals.
The ioctl doesn't wipe pagecache pages. Thus, we tolerate that after a
kernel compromise some portions of plaintext file contents may still be
recoverable from memory. This can be solved by enabling page poisoning
system-wide, which security conscious users may choose to do. But it's
very difficult to solve otherwise, e.g. note that plaintext file
contents may have been read in other places than pagecache pages.
Like FS_IOC_ADD_ENCRYPTION_KEY, FS_IOC_REMOVE_ENCRYPTION_KEY is
initially restricted to privileged users only. This is sufficient for
some use cases, but not all. A later patch will relax this restriction,
but it will require introducing key hashes, among other changes.
Reviewed-by: Theodore Ts'o <[email protected]>
Signed-off-by: Eric Biggers <[email protected]>
|
|
Add a new fscrypt ioctl, FS_IOC_ADD_ENCRYPTION_KEY. This ioctl adds an
encryption key to the filesystem's fscrypt keyring ->s_master_keys,
making any files encrypted with that key appear "unlocked".
Why we need this
~~~~~~~~~~~~~~~~
The main problem is that the "locked/unlocked" (ciphertext/plaintext)
status of encrypted files is global, but the fscrypt keys are not.
fscrypt only looks for keys in the keyring(s) the process accessing the
filesystem is subscribed to: the thread keyring, process keyring, and
session keyring, where the session keyring may contain the user keyring.
Therefore, userspace has to put fscrypt keys in the keyrings for
individual users or sessions. But this means that when a process with a
different keyring tries to access encrypted files, whether they appear
"unlocked" or not is nondeterministic. This is because it depends on
whether the files are currently present in the inode cache.
Fixing this by consistently providing each process its own view of the
filesystem depending on whether it has the key or not isn't feasible due
to how the VFS caches work. Furthermore, while sometimes users expect
this behavior, it is misguided for two reasons. First, it would be an
OS-level access control mechanism largely redundant with existing access
control mechanisms such as UNIX file permissions, ACLs, LSMs, etc.
Encryption is actually for protecting the data at rest.
Second, almost all users of fscrypt actually do need the keys to be
global. The largest users of fscrypt, Android and Chromium OS, achieve
this by having PID 1 create a "session keyring" that is inherited by
every process. This works, but it isn't scalable because it prevents
session keyrings from being used for any other purpose.
On general-purpose Linux distros, the 'fscrypt' userspace tool [1] can't
similarly abuse the session keyring, so to make 'sudo' work on all
systems it has to link all the user keyrings into root's user keyring
[2]. This is ugly and raises security concerns. Moreover it can't make
the keys available to system services, such as sshd trying to access the
user's '~/.ssh' directory (see [3], [4]) or NetworkManager trying to
read certificates from the user's home directory (see [5]); or to Docker
containers (see [6], [7]).
By having an API to add a key to the *filesystem* we'll be able to fix
the above bugs, remove userspace workarounds, and clearly express the
intended semantics: the locked/unlocked status of an encrypted directory
is global, and encryption is orthogonal to OS-level access control.
Why not use the add_key() syscall
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We use an ioctl for this API rather than the existing add_key() system
call because the ioctl gives us the flexibility needed to implement
fscrypt-specific semantics that will be introduced in later patches:
- Supporting key removal with the semantics such that the secret is
removed immediately and any unused inodes using the key are evicted;
also, the eviction of any in-use inodes can be retried.
- Calculating a key-dependent cryptographic identifier and returning it
to userspace.
- Allowing keys to be added and removed by non-root users, but only keys
for v2 encryption policies; and to prevent denial-of-service attacks,
users can only remove keys they themselves have added, and a key is
only really removed after all users who added it have removed it.
Trying to shoehorn these semantics into the keyrings syscalls would be
very difficult, whereas the ioctls make things much easier.
However, to reuse code the implementation still uses the keyrings
service internally. Thus we get lockless RCU-mode key lookups without
having to re-implement it, and the keys automatically show up in
/proc/keys for debugging purposes.
References:
[1] https://github.com/google/fscrypt
[2] https://goo.gl/55cCrI#heading=h.vf09isp98isb
[3] https://github.com/google/fscrypt/issues/111#issuecomment-444347939
[4] https://github.com/google/fscrypt/issues/116
[5] https://bugs.launchpad.net/ubuntu/+source/fscrypt/+bug/1770715
[6] https://github.com/google/fscrypt/issues/128
[7] https://askubuntu.com/questions/1130306/cannot-run-docker-on-an-encrypted-filesystem
Reviewed-by: Theodore Ts'o <[email protected]>
Signed-off-by: Eric Biggers <[email protected]>
|
|
Rename keyinfo.c to keysetup.c since this better describes what the file
does (sets up the key), and it matches the new file keysetup_v1.c.
Reviewed-by: Theodore Ts'o <[email protected]>
Signed-off-by: Eric Biggers <[email protected]>
|
|
More fscrypt definitions are being added, and we shouldn't use a
disproportionate amount of space in <linux/fs.h> for fscrypt stuff.
So move the fscrypt definitions to a new header <linux/fscrypt.h>.
For source compatibility with existing userspace programs, <linux/fs.h>
still includes the new header.
Reviewed-by: Theodore Ts'o <[email protected]>
Signed-off-by: Eric Biggers <[email protected]>
|
|
Since struct sg_table is used in nvme-fc-driver.h, include
<linux/scatterlist.h> from that header file.
Since no definitions or declarations from <linux/blk-mq.h> are used in the
qla_nvme.h header file, do not include <linux/blk-mq.h> from that header
file.
Cc: Himanshu Madhani <[email protected]>
Signed-off-by: Bart Van Assche <[email protected]>
Tested-by: Himanshu Madhani <[email protected]>
Reviewed-by: Himanshu Madhani <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
As of now, setting watches on filesystem objects has, at most, applied a
check for read access to the inode, and in the case of fanotify, requires
CAP_SYS_ADMIN. No specific security hook or permission check has been
provided to control the setting of watches. Using any of inotify, dnotify,
or fanotify, it is possible to observe, not only write-like operations, but
even read access to a file. Modeling the watch as being merely a read from
the file is insufficient for the needs of SELinux. This is due to the fact
that read access should not necessarily imply access to information about
when another process reads from a file. Furthermore, fanotify watches grant
more power to an application in the form of permission events. While
notification events are solely, unidirectional (i.e. they only pass
information to the receiving application), permission events are blocking.
Permission events make a request to the receiving application which will
then reply with a decision as to whether or not that action may be
completed. This causes the issue of the watching application having the
ability to exercise control over the triggering process. Without drawing a
distinction within the permission check, the ability to read would imply
the greater ability to control an application. Additionally, mount and
superblock watches apply to all files within the same mount or superblock.
Read access to one file should not necessarily imply the ability to watch
all files accessed within a given mount or superblock.
In order to solve these issues, a new LSM hook is implemented and has been
placed within the system calls for marking filesystem objects with inotify,
fanotify, and dnotify watches. These calls to the hook are placed at the
point at which the target path has been resolved and are provided with the
path struct, the mask of requested notification events, and the type of
object on which the mark is being set (inode, superblock, or mount). The
mask and obj_type have already been translated into common FS_* values
shared by the entirety of the fs notification infrastructure. The path
struct is passed rather than just the inode so that the mount is available,
particularly for mount watches. This also allows for use of the hook by
pathname-based security modules. However, since the hook is intended for
use even by inode based security modules, it is not placed under the
CONFIG_SECURITY_PATH conditional. Otherwise, the inode-based security
modules would need to enable all of the path hooks, even though they do not
use any of them.
This only provides a hook at the point of setting a watch, and presumes
that permission to set a particular watch implies the ability to receive
all notification about that object which match the mask. This is all that
is required for SELinux. If other security modules require additional hooks
or infrastructure to control delivery of notification, these can be added
by them. It does not make sense for us to propose hooks for which we have
no implementation. The understanding that all notifications received by the
requesting application are all strictly of a type for which the application
has been granted permission shows that this implementation is sufficient in
its coverage.
Security modules wishing to provide complete control over fanotify must
also implement a security_file_open hook that validates that the access
requested by the watching application is authorized. Fanotify has the issue
that it returns a file descriptor with the file mode specified during
fanotify_init() to the watching process on event. This is already covered
by the LSM security_file_open hook if the security module implements
checking of the requested file mode there. Otherwise, a watching process
can obtain escalated access to a file for which it has not been authorized.
The selinux_path_notify hook implementation works by adding five new file
permissions: watch, watch_mount, watch_sb, watch_reads, and watch_with_perm
(descriptions about which will follow), and one new filesystem permission:
watch (which is applied to superblock checks). The hook then decides which
subset of these permissions must be held by the requesting application
based on the contents of the provided mask and the obj_type. The
selinux_file_open hook already checks the requested file mode and therefore
ensures that a watching process cannot escalate its access through
fanotify.
The watch, watch_mount, and watch_sb permissions are the baseline
permissions for setting a watch on an object and each are a requirement for
any watch to be set on a file, mount, or superblock respectively. It should
be noted that having either of the other two permissions (watch_reads and
watch_with_perm) does not imply the watch, watch_mount, or watch_sb
permission. Superblock watches further require the filesystem watch
permission to the superblock. As there is no labeled object in view for
mounts, there is no specific check for mount watches beyond watch_mount to
the inode. Such a check could be added in the future, if a suitable labeled
object existed representing the mount.
The watch_reads permission is required to receive notifications from
read-exclusive events on filesystem objects. These events include accessing
a file for the purpose of reading and closing a file which has been opened
read-only. This distinction has been drawn in order to provide a direct
indication in the policy for this otherwise not obvious capability. Read
access to a file should not necessarily imply the ability to observe read
events on a file.
Finally, watch_with_perm only applies to fanotify masks since it is the
only way to set a mask which allows for the blocking, permission event.
This permission is needed for any watch which is of this type. Though
fanotify requires CAP_SYS_ADMIN, this is insufficient as it gives implicit
trust to root, which we do not do, and does not support least privilege.
Signed-off-by: Aaron Goidel <[email protected]>
Acked-by: Casey Schaufler <[email protected]>
Acked-by: Jan Kara <[email protected]>
Signed-off-by: Paul Moore <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First set of new device support, features and cleanups for IIO in the 5.4 cycle
Note includes a merge from i3c tree to get support needed for stm_lsm6dsx driver
support for l3c devices. Done from immutable branch.
A counter subsystem patche in here as well.
Alongside the new device support (which is always good), Chuhong's work
on using devres managed APIs has cleaned up a number of drivers.
New device support
* adis16460
- New driver based on ADIS framework which needed addition of support
for cs_change_delay. Includes device tree binding.
* cros_ec
- Support fo the veyron-minnie which uses an older interface.
* lsm6dsx
- Support for LSM6DSTR-C gyro + magnetometer sensor (new IDs mainly)
- Support for ISM330DHCX acc + gyro sensor (extensive rework needed!)
* Maxim 5432
- New driver support MAX5432-MAX5435 family of potentiometers.
* noa1305
- New driver for this ON Semiconductor Ambient light sensor.
Features and cleanups
* tree wide
- Drop error prints after platform_get_irq as already prints errors
internally if any occur.
* docs
- Document mounting matrix.
- Fix a missing newline at end of file.
* ad2s1210
- Switch to device managed APIs for all of probe and drop explicit remove.
* ad7192
- Add of_device_id array to explicity handling DT bindings.
* ad7606
- Lots of rework leading to support for software configure modes in ad7616
parts.
- Debugfs register access support.
* am2315
- Switch to device managed APIs for all of probe and drop explicit remove.
* apds9960
- Typo in module description.
* cm36651
- Convert to i2c_new_dummy_device.
- Swithc to device managed APIs for all of probe adn drop explicit remove.
* cros_ec
- Calibscale support for accel, gyro and magnetometer.
- Tidy up some error codes to return the error from the stack rather than
-EIO.
- Determine protocol version.
- Add a sign vector to the core to fix sensor rotation if necessary.
Cannot just be done with mount matrix as already in use in many devices.
- Tidy up INFO_SCALE being in both the separate and shared lists.
- Drop a lot of dplicate code from the cros-ec-accel-legacy driver
and use the core provided code instead.
- Make frequency range available to userspace.
* counter / ftm-quaddec
- Switch to device managed APIs for all of probe adn drop explicit remove.
* hdc100x
- Switch to device managed APIs for all of probe and drop explicit remove.
* hi8435
- Use gpiod_set_value_cansleep as we don't care here and there is a
board out there where it needs to sleep.
- Switch to device managed APIs for all of probe and drop explict remove.
* hp03
- Convert to i2c_new_dummy_device.
* maxim thermocouple
- Switch to device managed APIs for all of probe and drop explicit remove.
* mmc35240
- Fix typo in constant naming.
* mpu6050
- Use devm_add_action_or_reset in place of explicit error handling.
- Make text in Kconfig more explicit about which parts are supported.
* mxc4005
- Switch to device managed APIs for all of probe and drop explicit remove.
* pms7003
- Convert device tree bindings to yaml.
- Add a MAINTAINERS entry
* sc27xx
- Introduce a local struct device *dev pointer to avoid lots of deref.
- Use devm_add_action_or_reset in place of explicit error handling.
* sca3000
- Typo fix in naming.
* si1145
- Switch to device managed APIs for all of probe and drop explicit remove.
* st_sensors
- Lots of rework to enable switch to regmap.
- Regmap conversion at the end.
- Tidy up some inconsistencies in buffer setup ops.
- Tidy up an oddity by dropping get_irq_data_ready function in favour
of direct access.
- Stop allocating buffer in buffer enable in favour of just embedding
a large enough constant size buffer in the iio_priv accessed structure.
* st_lsm6dsx
- l3c device support (LSM6DSO and LSM6DSR)
- tidy up irq return logic which was strangely written.
- fix up an ABI quirk where this driver used separate scale
attributes, even though they were always shared by type.
* stk33xx
- Device tree bindings include manufacturer ID.
* stm32-adc
- Add control for supply to analog switches including DT bindings.
* stm32 timer
- Drop the quadrature mode support. Believed there were no users so
take this opportunity to drop this unwanted ABI.
* tsl2772
- Switch to device mangage APIs for all of probe and drop explicit remove.
- Use regulator_bulk_* APIs to reduce repitition.
* veml6070
- Convert to i2c_new_dummy_device.
* tag 'iio-for-5.4a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (84 commits)
iio: hi8435: Drop hi8435_remove() by using devres for remaining elements
iio: hi8435: Use gpiod_set_value_cansleep()
iio:st_sensors: remove buffer allocation at each buffer enable
iio: imu: inv_mpu6050: be more explicit on supported chips
iio: light: noa1305: Add support for NOA1305
dt-bindings: Add binding document for NOA1305
iio: remove get_irq_data_ready() function pointer and use IRQ number directly
iio: imu: st_lsm6dsx: make IIO_CHAN_INFO_SCALE shared by type
iio: tsl2772: Use regulator_bulk_() APIs
iio: tsl2772: Use devm_iio_device_register
iio: tsl2772: Use devm_add_action_or_reset for tsl2772_chip_off
iio: tsl2772: Use devm_add_action_or_reset
iio: Remove dev_err() usage after platform_get_irq()
iio: light: si1145: Use device-managed APIs
iio:pressure: preenable/postenable/predisable fixup for ST press buffer
iio:magn: preenable/postenable/predisable fixup for ST magn buffer
iio:gyro: preenable/postenable/predisable fixup for ST gyro buffer
iio:accel: preenable/postenable/predisable fixup for ST accel buffer
dt-bindings: iio: imu: st_lsm6dsx: add ism330dhcx device bindings
iio: imu: st_lsm6dsx: add support to ISM330DHCX
...
|
|
Some of i.MX8 processors (e.g i.MX8QM, i.MX8QXP) contain
the Tensilica HiFi4 DSP for advanced pre- and post-audio
processing.
The communication between Host CPU and DSP firmware is
taking place using a shared memory area for message passing
and a dedicated Messaging Unit for notifications.
DSP IPC protocol offers a doorbell interface using
imx-mailbox API.
We use 4 MU channels (2 x TXDB, 2 x RXDB) to implement a
request-reply protocol.
Connection 0 (txdb0, rxdb0):
- Host writes messasge to shared memory [SHMEM]
- Host sends a request [MU]
- DSP handles request [SHMEM]
- DSP sends reply [MU]
Connection 1 (txdb1, rxdb1):
- DSP writes a message to shared memory [SHMEM]
- DSP sends a request [MU]
- Host handles request [SHMEM]
- Host sends reply [MU]
The protocol interface will be used by a Host client to
communicate with the DSP. First client will be the i.MX8
part from Sound Open Firmware infrastructure.
The protocol offers the following interface:
On Tx:
- imx_dsp_ring_doorbell, will be called to notify the DSP
that it needs to handle a request.
On Rx:
- clients need to provide two callbacks:
.handle_reply
.handle_request
- the callbacks will be used by the protocol on
notification arrival from DSP.
Signed-off-by: Daniel Baluta <[email protected]>
Reviewed-by: Oleksij Rempel <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
ACPI 6.3 adds a flag to the CPU node to indicate whether
the given PE is a thread. Add a function to return that
information for a given linux logical CPU.
Signed-off-by: Jeremy Linton <[email protected]>
Reviewed-by: Sudeep Holla <[email protected]>
Reviewed-by: Robert Richter <[email protected]>
Acked-by: Rafael J. Wysocki <[email protected]>
Signed-off-by: Will Deacon <[email protected]>
|
|
In order to support different types of irq design, we decide to add
separate irq drivers for different design and keep mt6397 mfd core
simple and reusable to all generations of PMICs so far.
Signed-off-by: Hsin-Hsiung Wang <[email protected]>
Signed-off-by: Lee Jones <[email protected]>
|
|
SCMIv2.0 adds a new Reset Management Protocol to manage various reset
states a given device or domain can enter. Device(s) that can be
collectively reset through a common reset signal constitute a reset
domain for the firmware.
A reset domain can be reset autonomously or explicitly through assertion
and de-assertion of the signal. When autonomous reset is chosen, the
firmware is responsible for taking the necessary steps to reset the
domain and to subsequently bring it out of reset. When explicit reset is
chosen, the caller has to specifically assert and then de-assert the
reset signal by issuing two separate RESET commands.
Add the basic SCMI reset infrastructure that can be used by Linux
reset controller driver.
Reviewed-by: Peng Fan <[email protected]>
Reviewed-by: Philipp Zabel <[email protected]>
Signed-off-by: Sudeep Holla <[email protected]>
|
|
CLOCK_PROTOCOL_ATTRIBUTES provides attributes to indicate the maximum
number of pending asynchronous clock rate changes supported by the
platform. If it's non-zero, then we should be able to use asynchronous
clock rate set for any clocks until the maximum limit is reached.
In order to add that support, let's drop the config flag passed to
clk_ops->rate_set and handle the asynchronous requests dynamically.
Cc: Stephen Boyd <[email protected]>
Cc: [email protected]
Acked-by: Stephen Boyd <[email protected]>
Signed-off-by: Sudeep Holla <[email protected]>
|
|
SENSOR_DESCRIPTION_GET provides attributes to indicate if the sensor
supports asynchronous read. We can read that flag and use asynchronous
reads for any sensors with that attribute set.
Let's use the new scmi_do_xfer_with_response to support asynchronous
sensor reads.
Signed-off-by: Sudeep Holla <[email protected]>
|
|
SENSOR_DESCRIPTION_GET provides attributes to indicate if the sensor
supports asynchronous read. Ideally we should be able to read that flag
and use asynchronous reads for any sensors with that attribute set.
In order to add that support, let's drop the async flag passed to
sensor_ops->reading_get and dynamically switch between sync and async
flags based on the attributes as provided by the firmware.
Cc: [email protected]
Acked-by: Guenter Roeck <[email protected]>
Signed-off-by: Sudeep Holla <[email protected]>
|
|
Looks like more code developed during the draft versions of the
specification slipped through and they don't match the final
released version. This seem to have happened only with sensor
protocol.
Renaming few command and function names here to match exactly with
the released version of SCMI specification for ease of maintenance.
Signed-off-by: Sudeep Holla <[email protected]>
|