| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The amount of chain next pointer elements between the producer
and the consumer indices depends on which pages they currently
point to. The current calculation is based only on their difference,
and it can lead to a number of free elements which is higher by 1
than the actual value.
Signed-off-by: Tomer Tayar <[email protected]>
Signed-off-by: Manish Chopra <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Physical LEDs are being controlled by the management FW.
This adds the qed functionality required to request management FW to
change the LED configuration, as well as the necessary APIs for this
functionality to later be used by the protocol drivers.
Signed-off-by: Sudarsana Kalluru <[email protected]>
Signed-off-by: Yuval Mintz <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Device statistics can be gathered on-demand. This adds the qed support for
reading the statistics [both function and port] from the device, and adds
to the public API a method for requesting the current statistics.
Signed-off-by: Manish Chopra <[email protected]>
Signed-off-by: Yuval Mintz <[email protected]>
Signed-off-by: Ariel Elior <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Physical link is handled by the management Firmware.
This patch lays the infrastructure for attention handling in the driver,
as link change notifications arrive via async. attentions,
as well the handling of such notifications.
This patch also extends the API with the protocol drivers by adding
registered callbacks which the protocol driver passes to qed in order
to be notified of async. events originating from the FW/HW.
Signed-off-by: Yuval Mintz <[email protected]>
Signed-off-by: Ariel Elior <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This patch adds to the qed the support to configure various L2 elements,
such as channels and basic filtering conditions.
It also enhances its public API to allow qede to later utilize this
functionality.
Signed-off-by: Manish Chopra <[email protected]>
Signed-off-by: Yuval Mintz <[email protected]>
Signed-off-by: Ariel Elior <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This patch adds a public API for a network driver to work on top of QED.
The interface itself is very minimal - it's mostly infrastructure, as the
only content it has after this patch is a query for HW-based information
required for the creation of a network interface [I.e., no actual
protocol-specific configurations are supported].
Signed-off-by: Manish Chopra <[email protected]>
Signed-off-by: Yuval Mintz <[email protected]>
Signed-off-by: Ariel Elior <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The Qlogic Everest Driver is the backend module for the QL4xxx ethernet
products by Qlogic.
This module serves two main purposes:
1. It's responsible to contain all the common code that will be shared
between the various drivers that would be used with said line of
products. Flows such as chip initialization and de-initialization
fall under this category.
2. It would abstract the protocol-specific HW & FW components, allowing
the protocol drivers to have a clean APIs which is detached in its
slowpath configuration from the actual HSI.
This adds a very basic module without any protocol-specific bits.
I.e., this adds a basic implementation that almost entirely falls under
the first category.
Signed-off-by: Yuval Mintz <[email protected]>
Signed-off-by: Ariel Elior <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|