| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Winbond spi-nor flash 32MB and larger have an 'Extended Address
Register' as one option for addressing beyond 16MB (Macronix
has the same concept, Spansion has EXTADD bits in the Bank Address
Register).
According to section
8.2.7 Write Extended Address Register (C5h)
of the Winbond W25Q256FV data sheet (256M-BIT SPI flash)
The Extended Address Register is only effective when the device is
in the 3-Byte Address Mode. When the device operates in the 4-Byte
Address Mode (ADS=1), any command with address input of A31-A24
will replace the Extended Address Register values. It is
recommended to check and update the Extended Address Register if
necessary when the device is switched from 4-Byte to 3-Byte Address
Mode.
So the documentation suggests clearing the EAR after switching to
3-byte mode. Experimentation shows that the EAR is *always* one after
the switch to 3-byte mode, so clearing the EAR is mandatory at
shutdown for a subsequent 3-byte-addressed reboot to work.
Note that some SOCs (e.g. MT7621) do not assert a reset line at normal
reboot, so we cannot rely on hardware reset. The MT7621 does assert a
reset line at watchdog-reset.
Acked-by: Marek Vasut <[email protected]>
Signed-off-by: NeilBrown <[email protected]>
Signed-off-by: Boris Brezillon <[email protected]>
|
|
Core changes:
* Prepare arrival of the SPI NAND subsystem by implementing a generic
(interface-agnostic) layer to ease manipulation of NAND devices
* Move onenand code base to the drivers/mtd/nand/ dir
* Rework timing mode selection
* Provide a generic way for NAND chip drivers to flag a specific
GET/SET FEATURE operation as supported/unsupported
* Stop embedding ONFI/JEDEC param page in nand_chip
Driver changes:
* Rework/cleanup of the mxc driver
* Various cleanups in the vf610 driver
* Migrate the fsmc and vf610 to ->exec_op()
* Get rid of the pxa driver (replaced by marvell_nand)
* Support ->setup_data_interface() in the GPMI driver
* Fix probe error path in several drivers
* Remove support for unused hw_syndrome mode in sunxi_nand
* Various minor improvements
|
|
In order to properly support compatibility strings as described in the
bindings/mtd/partition.txt "ofpart" type should be treated as an
indication for looking into OF. MTD should check "compatible" property
and search for a matching parser rather than blindly trying the one
supporting "fixed-partitions".
It also means that existing "fixed-partitions" parser should get renamed
to use a more meaningful name.
This commit achievies that aim by introducing a new mtd_part_of_parse().
It works by looking for a matching parser for every string in the
"compatibility" property (starting with the most specific one).
Please note that driver-specified parsers still take a precedence. It's
assumed that driver providing a parser type has a good reason for that
(e.g. having platform data with device-specific info). Also doing
otherwise could break existing setups. The same applies to using default
parsers (including "cmdlinepart") as some overwrite DT data with cmdline
argument.
Partition parsers can now provide an of_match_table to enable
flash<-->parser matching via device tree as documented in the
mtd/partition.txt.
This support is currently limited to built-in parsers as it uses
request_module() and friends. This should be sufficient for most cases
though as compiling parsers as modules isn't a common choice.
Signed-off-by: Brian Norris <[email protected]>
Signed-off-by: Rafał Miłecki <[email protected]>
Tested-by: Peter Rosin <[email protected]>
Reviewed-by: Richard Weinberger <[email protected]>
Signed-off-by: Boris Brezillon <[email protected]>
|
|
MTD users are no longer checking erase_info->state to determine if the
erase operation failed or succeeded. Moreover, mtd_erase_callback() is
now a NOP.
We can safely get rid of all mtd_erase_callback() calls and all
erase_info->state assignments. While at it, get rid of the
erase_info->state field, all MTD_ERASE_XXX definitions and the
mtd_erase_callback() function.
Signed-off-by: Boris Brezillon <[email protected]>
Reviewed-by: Richard Weinberger <[email protected]>
Reviewed-by: Miquel Raynal <[email protected]>
Acked-by: Bert Kenward <[email protected]>
---
Changes in v2:
- Address a few coding style issues (reported by Miquel)
- Remove comments that are no longer valid (reported by Miquel)
|
|
The NAND chip parameter page is statically allocated within the
nand_chip structure, which reserves a lot of space. Even not ONFI nor
JEDEC chips have it embedded. Also, only a few parameters are actually
read from the parameter page after the detection.
Now that there is a small nand_parameters structure that hold all needed
ONFI parameters, remove the ONFI page from the nand_chip structure by
just allocating it during the identification phase and removing it right
after.
Signed-off-by: Miquel Raynal <[email protected]>
Signed-off-by: Boris Brezillon <[email protected]>
|
|
The NAND chip parameter page is statically allocated within the
nand_chip structure, which reserves a lot of space. Even not ONFI nor
JEDEC chips have it embedded. Also, only a few parameters are actually
read from the parameter page after the detection.
Now that there is a small nand_parameters structure that can held
generic parameters, remove the JEDEC page from the nand_chip structure
by just allocating it during the identification phase and removing it
right after.
Signed-off-by: Miquel Raynal <[email protected]>
Signed-off-by: Boris Brezillon <[email protected]>
|
|
If SET/GET_FEATURES is available (from the parameter page), use a
bitmap to declare what feature is actually supported.
Initialize the bitmap in the core to support timing changes (only
feature used by the core), also add support for Micron specific features
used in Micron initialization code (in the init routine).
Signed-off-by: Miquel Raynal <[email protected]>
Signed-off-by: Boris Brezillon <[email protected]>
|
|
The NAND chip parameter page is statically allocated within the
nand_chip structure, which reserves a lot of space. Even not ONFI nor
JEDEC chips have it embedded. Also, only a few parameters are actually
read from the parameter page after the detection.
ONFI-related parameters that will be used outside from the
identification function are stored in a separate onfi_parameters
structure embedded in nand_parameters, this small structure that
already hold generic parameters.
For now, the onfi_parameters structure is allocated statically. However,
after some deep rework in the NAND framework, it will be possible to do
dynamic allocations from the NAND identification phase, and this
strcuture will then be dynamically allocated when needed.
Signed-off-by: Miquel Raynal <[email protected]>
Signed-off-by: Boris Brezillon <[email protected]>
|
|
The NAND chip parameter page is statically allocated within the
nand_chip structure, which reserves a lot of space. Even not ONFI nor
JEDEC chips have it embedded. Also, only a few parameters are actually
read from the parameter page after the detection.
To prepare to the removal of such huge structure, a small NAND parameter
structure is allocated statically and contains only very few members
that are generic to all chips and actually used elsewhere in the code.
Signed-off-by: Miquel Raynal <[email protected]>
Signed-off-by: Boris Brezillon <[email protected]>
|
|
Prepare the fact that some features managed by GET/SET_FEATURES could be
overloaded by vendor code. To handle this logic, use new wrappers
instead of directly call the ->get/set_features() hooks.
Signed-off-by: Miquel Raynal <[email protected]>
Signed-off-by: Boris Brezillon <[email protected]>
|
|
SET/GET FEATURES are flagged ONFI-compliant because of their name. This
is not accurate as non-ONFI NAND chips support it and use it.
Rename the hooks and helpers to remove the "onfi" prefix.
Signed-off-by: Miquel Raynal <[email protected]>
Signed-off-by: Boris Brezillon <[email protected]>
|
|
->fail_addr and ->addr can be updated no matter the result of
parent->_erase(), we just need to remove the code doing the same thing
in mtd_erase_callback() to avoid adjusting those fields twice.
Note that this can be done because all MTD users have been converted to
not pass an erase_info->callback() and are thus only taking the
->addr_fail and ->addr fields into account after part_erase() has
returned.
While we're at it, get rid of the erase_info->mtd field which was only
needed to let mtd_erase_callback() get the partition device back.
Signed-off-by: Boris Brezillon <[email protected]>
Reviewed-by: Richard Weinberger <[email protected]>
|
|
None of the mtd->_erase() implementations work in an asynchronous manner,
so let's simplify MTD users that call mtd_erase(). All they need to do
is check the value returned by mtd_erase() and assume that != 0 means
failure.
Signed-off-by: Boris Brezillon <[email protected]>
Reviewed-by: Richard Weinberger <[email protected]>
|
|
Some fields are not used by MTD drivers, users or core code. Moreover,
those fields are not documented, so get rid of them to avoid any
confusion.
Signed-off-by: Boris Brezillon <[email protected]>
Reviewed-by: Richard Weinberger <[email protected]>
|
|
Add an intermediate layer to abstract NAND device interface so that
some logic can be shared between SPI NANDs, parallel/raw NANDs,
OneNANDs, ...
Signed-off-by: Boris Brezillon <[email protected]>
|
|
Some files add a comment giving the path of the file inside the Linux
tree, which is pretty useless since the reader had to find the file to
open it.
Getting rid of these comments will also allow us to easily move these
files around when needed.
Signed-off-by: Boris Brezillon <[email protected]>
|
|
Pull NAND changes from Boris Brezillon:
"
Core changes:
* Fix NAND_CMD_NONE handling in nand_command[_lp]() hooks
* Introduce the ->exec_op() infrastructure
* Rework NAND buffers handling
* Fix ECC requirements for K9F4G08U0D
* Fix nand_do_read_oob() to return the number of bitflips
* Mark K9F1G08U0E as not supporting subpage writes
Driver changes:
* MTK: Rework the driver to support new IP versions
* OMAP OneNAND: Full rework to use new APIs (libgpio, dmaengine) and fix
DT support
* Marvell: Add a new driver to replace the pxa3xx one
"
|
|
Pull spi-nor changes from Cyrille Pitchen:
"
This pull-request contains the following notable changes:
Core changes:
* Add support to new ISSI and Cypress/Spansion memory parts.
* Fix support of Micron memories by checking error bits in the FSR.
* Fix update of block-protection bits by reading back the SR.
* Restore the internal state of the SPI flash memory when removing the
device.
Driver changes:
* Maintenance for Freescale, Intel and Metiatek drivers.
* Add support of the direct access mode for the Cadence QSPI controller.
"
|
|
GCC-4.4.4 raises errors when assigning a parameter in an anonymous
union, leading to this kind of failure:
drivers/mtd/nand/marvell_nand.c:1936:
warning: missing braces around initializer
warning: (near initialization for '(anonymous)[1].<anonymous>')
error: unknown field 'data' specified in initializer
error: unknown field 'addr' specified in initializer
Work around the situation by naming these unions.
Fixes: 8878b126df76 ("mtd: nand: add ->exec_op() implementation")
Reported-by: Andrew Morton <[email protected]>
Signed-off-by: Miquel Raynal <[email protected]>
Tested-by: Andrew Morton <[email protected]>
Signed-off-by: Boris Brezillon <[email protected]>
|
|
There's currently nothing forcing alignment of einfo->addr and
einfo->len on mtd->erasesize. Since we don't know if automatically
aligning those field in mtd_erase() will hurt some drivers, we add an
helper function to let drivers that need such an alignment explicitly
ask for it.
Signed-off-by: Boris Brezillon <[email protected]>
Reviewed-by: Miquel Raynal <[email protected]>
|
|
The map_word_() functions, dating back to linux-2.6.8, try to perform
bitwise operations on a 'map_word' structure. This may have worked
with compilers that were current then (gcc-3.4 or earlier), but end
up being rather inefficient on any version I could try now (gcc-4.4 or
higher). Specifically we hit a problem analyzed in gcc PR81715 where we
fail to reuse the stack space for local variables.
This can be seen immediately in the stack consumption for
cfi_staa_erase_varsize() and other functions that (with CONFIG_KASAN)
can be up to 2200 bytes. Changing the inline functions into macros brings
this down to 1280 bytes. Without KASAN, the same problem exists, but
the stack consumption is lower to start with, my patch shrinks it from
920 to 496 bytes on with arm-linux-gnueabi-gcc-5.4, and saves around
1KB in .text size for cfi_cmdset_0020.c, as it avoids copying map_word
structures for each call to one of these helpers.
With the latest gcc-8 snapshot, the problem is fixed in upstream gcc,
but nobody uses that yet, so we should still work around it in mainline
kernels and probably backport the workaround to stable kernels as well.
We had a couple of other functions that suffered from the same gcc bug,
and all of those had a simpler workaround involving dummy variables
in the inline function. Unfortunately that did not work here, the
macro hack was the best I could come up with.
It would also be helpful to have someone to a little performance testing
on the patch, to see how much it helps in terms of CPU utilitzation.
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=81715
Cc: [email protected]
Signed-off-by: Arnd Bergmann <[email protected]>
Acked-by: Richard Weinberger <[email protected]>
Signed-off-by: Boris Brezillon <[email protected]>
|
|
Introduce a new interface to instruct NAND controllers to send specific
NAND operations. The new interface takes the form of a single method
called ->exec_op(). This method is designed to replace ->cmd_ctrl(),
->cmdfunc() and ->read/write_byte/word/buf() hooks.
->exec_op() is passed a set of instructions describing the operation
to execute. Each instruction has a type (ADDR, CMD, DATA, WAITRDY)
and delay. The delay is here to help simple controllers wait enough
time between each instruction, advanced controllers with integrated
timings control can ignore these delays.
Controllers that natively support complex operations (operations
formed of several instructions) can use the NAND op parser
infrastructure. This infrastructure allows controller drivers to
describe the sequence of instructions they support (called
nand_op_pattern) and a hook for each of these supported sequences. The
core then tries to find the best match for a given NAND operation, and
calls the associated hook.
Various other helpers are also added to ease NAND controller drivers
writing.
This new interface should ease support of vendor specific operations
in that NAND manufacturer drivers now have a way to check if the
controller they are connected to supports a specific operation, and
complain or refuse to probe the NAND chip when that's not the case.
Suggested-by: Boris Brezillon <[email protected]>
Signed-off-by: Miquel Raynal <[email protected]>
Signed-off-by: Boris Brezillon <[email protected]>
|
|
struct nand_buffers is malloc'ed in nand_scan_tail() just for
containing three pointers. Squash this struct into nand_chip.
Move and rename as follows:
chip->buffers->ecccalc -> chip->ecc.calc_buf
chip->buffers->ecccode -> chip->ecc.code_buf
chip->buffers->databuf -> chip->data_buf
Signed-off-by: Masahiro Yamada <[email protected]>
Signed-off-by: Boris Brezillon <[email protected]>
|
|
The last/only user of NAND_OWN_BUFFERS (cafe_nand.c) has been reworked.
This flag is no longer needed.
Suggested-by: Boris Brezillon <[email protected]>
Signed-off-by: Masahiro Yamada <[email protected]>
Signed-off-by: Boris Brezillon <[email protected]>
|
|
Right now, the chip->data_interface field is populated in
nand_scan_tail(), so after the whole NAND detection has taken place.
This is fine because these timings are not yet used by the core so
early in the probe process, but the situation is about to change with
the introduction of ->exec_op().
Also, by convention, nand_scan_ident() is not supposed to allocate
resources, only nand_scan_tail() can, so this prevent us from
allocating and initializing the data_interface object in
nand_scan_ident().
In order to solve this problem, directly embed a data_interface object
in nand_chip so that we don't have to allocate it, and initialize it to
ONFI SDR mode 0 at the very beginning of nand_scan_ident().
Signed-off-by: Miquel Raynal <[email protected]>
Signed-off-by: Boris Brezillon <[email protected]>
|
|
The core currently send the READ0 and SEQIN+PAGEPROG commands in
nand_do_read/write_ops(). This is inconsistent with
->read/write_oob[_raw]() hooks behavior which are expected to send
these commands.
There's already a flag (NAND_ECC_CUSTOM_PAGE_ACCESS) to inform the core
that a specific controller wants to send the READ/SEQIN+PAGEPROG
commands on its own, but it's an opt-in flag, and existing drivers are
unlikely to be updated to pass it.
Moreover, some controllers cannot dissociate the READ/PAGEPROG commands
from the associated data transfer and ECC engine activation, and
developers have to hack things in their ->cmdfunc() implementation to
handle such complex cases, or have to accept the perf penalty of sending
twice the same command.
To address this problem we are planning on adding a new interface which
is passed all information about a NAND operation (including the amount
of data to transfer) and replacing all calls to ->cmdfunc() to calls to
this new ->exec_op() hook. But, in order to do that, we need to have all
->cmdfunc() calls placed near their associated ->read/write_buf/byte()
calls.
Modify the core and relevant drivers to make NAND_ECC_CUSTOM_PAGE_ACCESS
the default case, and remove this flag.
Signed-off-by: Boris Brezillon <[email protected]>
[[email protected]: tested, fixed and rebased on nand/next]
Signed-off-by: Miquel Raynal <[email protected]>
Acked-by: Masahiro Yamada <[email protected]>
|
|
This is part of the process of removing direct calls to ->cmdfunc()
outside of the core in order to introduce a better interface to execute
NAND operations.
Here we provide several helpers and make use of them to remove all
direct calls to ->cmdfunc(). This way, we can easily modify those
helpers to make use of the new ->exec_op() interface when available.
Signed-off-by: Boris Brezillon <[email protected]>
[[email protected]: rebased and fixed some conflicts]
Signed-off-by: Miquel Raynal <[email protected]>
Acked-by: Masahiro Yamada <[email protected]>
|
|
Add this API to restore the status of SPI flash chip to the default
such as addressing mode, whenever detach the driver from device or
reboot the system.
Signed-off-by: Hou Zhiqiang <[email protected]>
Signed-off-by: Cyrille Pitchen <[email protected]>
|
|
For Micron spi nor device, when erase/program operation
fails, especially the failure results from intending to
modify protected space, spi-nor upper layers still get
the return which shows the operation succeeds. This is
because current spi_nor_fsr_ready() only uses FSR bit.7
(flag status register) to check device whether ready.
This patch fixes this issue by checking relevant error
bits in FSR.
The FSR is a powerful tool to investigate the status of
device, checking information regarding what the memory is
actually doing and detecting possible error conditions.
Signed-off-by: beanhuo <[email protected]>
Signed-off-by: Cyrille Pitchen <[email protected]>
|
|
Pull MTD updates from Richard Weinberger:
"General changes:
- Unconfuse get_unmapped_area and point/unpoint driver methods
- New partition parser: sharpslpart
- Kill GENERIC_IO
- Various fixes
NAND changes:
- Add a flag to mark NANDs that require 3 address cycles to encode a
page address
- Set a default ECC/free layout when NAND_ECC_NONE is requested
- Fix a bug in panic_nand_write()
- Another batch of cleanups for the denali driver
- Fix PM support in the atmel driver
- Remove support for platform data in the omap driver
- Fix subpage write in the omap driver
- Fix irq handling in the mtk driver
- Change link order of mtk_ecc and mtk_nand drivers to speed up boot
time
- Change log level of ECC error messages in the mxc driver
- Patch the pxa3xx driver to support Armada 8k platforms
- Add BAM DMA support to the qcom driver
- Convert gpio-nand to the GPIO desc API
- Fix ECC handling in the mt29f driver
SPI-NOR changes:
- Introduce system power management support
- New mechanism to select the proper .quad_enable() hook by JEDEC
ID, when needed, instead of only by manufacturer ID
- Add support to new memory parts from Gigadevice, Winbond, Macronix
and Everspin
- Maintainance for Cadence, Intel, Mediatek and STM32 drivers"
* tag 'for-linus-20171120' of git://git.infradead.org/linux-mtd: (85 commits)
mtd: Avoid probe failures when mtd->dbg.dfs_dir is invalid
mtd: sharpslpart: Add sharpslpart partition parser
mtd: Add sanity checks in mtd_write/read_oob()
mtd: remove the get_unmapped_area method
mtd: implement mtd_get_unmapped_area() using the point method
mtd: chips/map_rom.c: implement point and unpoint methods
mtd: chips/map_ram.c: implement point and unpoint methods
mtd: mtdram: properly handle the phys argument in the point method
mtd: mtdswap: fix spelling mistake: 'TRESHOLD' -> 'THRESHOLD'
mtd: slram: use memremap() instead of ioremap()
kconfig: kill off GENERIC_IO option
mtd: Fix C++ comment in include/linux/mtd/mtd.h
mtd: constify mtd_partition
mtd: plat-ram: Replace manual resource management by devm
mtd: nand: Fix writing mtdoops to nand flash.
mtd: intel-spi: Add Intel Lewisburg PCH SPI super SKU PCI ID
mtd: nand: mtk: fix infinite ECC decode IRQ issue
mtd: spi-nor: Add support for mr25h128
mtd: nand: mtk: change the compile sequence of mtk_nand.o and mtk_ecc.o
mtd: spi-nor: enable 4B opcodes for mx66l51235l
...
|
|
It is now unused.
Signed-off-by: Nicolas Pitre <[email protected]>
Reviewed-by: Richard Weinberger <[email protected]>
Acked-by: Boris Brezillon <[email protected]>
Tested-by: Chris Brandt <[email protected]>
Signed-off-by: Richard Weinberger <[email protected]>
|
|
C++ comments look wrong in kernel tree. Fix one.
Signed-off-by: Pavel Machek <[email protected]>
Acked-by: Boris Brezillon <[email protected]>
Signed-off-by: Richard Weinberger <[email protected]>
|
|
From Boris:
"
Core changes:
* Add a flag to mark NANDs that require 3 address cycles to encode a
page address
* Set a default ECC/free layout when NAND_ECC_NONE is requested
* Fix a bug in panic_nand_write()
Driver changes:
* Another batch of cleanups for the denali driver
* Fix PM support in the atmel driver
* Remove support for platform data in the omap driver
* Fix subpage write in the omap driver
* Fix irq handling in the mtk driver
* Change link order of mtk_ecc and mtk_nand drivers to speed up boot
time
* Change log level of ECC error messages in the mxc driver
* Patch the pxa3xx driver to support Armada 8k platforms
* Add BAM DMA support to the qcom driver
* Convert gpio-nand to the GPIO desc API
* Fix ECC handling in the mt29f driver
"
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <[email protected]>
Reviewed-by: Philippe Ombredanne <[email protected]>
Reviewed-by: Thomas Gleixner <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
This patch extracts some chunks from spi_nor_init_params and spi_nor_scan()
and moves them into a new spi_nor_init() function.
Indeed, spi_nor_init() regroups all the required SPI flash commands to be
sent to the SPI flash memory before performing any runtime operations
(Fast Read, Page Program, Sector Erase, ...). Hence spi_nor_init():
1) removes the flash protection if applicable for certain vendors.
2) sets the Quad Enable bit, if needed, before using Quad SPI protocols.
3) makes the memory enter its (stateful) 4-byte address mode, if needed,
for SPI flash memory > 128Mbits not supporting the 4-byte address
instruction set.
spi_nor_scan() now ends by calling spi_nor_init() once the probe phase has
completed. Further patches could also use spi_nor_init() to implement the
mtd->_resume() handler for the spi-nor framework.
Signed-off-by: Kamal Dasu <[email protected]>
Signed-off-by: Cyrille Pitchen <[email protected]>
|
|
There is exactly one board in the kernel that defines platform data
for the GPIO NAND driver.
Use the feature to provide a lookup table for the GPIOs in the board
file so we can convert the driver as a whole to just use GPIO
descriptors.
After this we can cut the use of <linux/of_gpio.h> and use the GPIO
descriptor management from <linux/gpio/consumer.h> alone to grab and use
the GPIOs used in the driver.
I also created a local struct device *dev in the probe() function
because I was getting annoyed with all the &pdev->dev dereferencing.
Cc: [email protected]
Cc: Mike Rapoport <[email protected]>
Cc: Frans Klaver <[email protected]>
Cc: Gerhard Sittig <[email protected]>
Cc: Jamie Iles <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
Acked-by: Jamie Iles <[email protected]>
Acked-by: Olof Johansson <[email protected]>
Acked-by: Robert Jarzmik <[email protected]>
Signed-off-by: Boris Brezillon <[email protected]>
|
|
Several drivers check ->chipsize to see if the third row address cycle
is needed. Instead of embedding magic sizes such as 32MB, 128MB in
drivers, introduce a new flag NAND_ROW_ADDR_3 for clean-up. Since
nand_scan_ident() knows well about the device, it can handle this
properly. The flag is set if the row address bit width is greater
than 16.
Delete comments such as "One more address cycle for ..." because
intention is now clear enough from the code.
Signed-off-by: Masahiro Yamada <[email protected]>
Acked-by: Wenyou Yang <[email protected]>
Signed-off-by: Boris Brezillon <[email protected]>
|
|
From Boris:
"
This pull request contains the following core changes:
* Fix memory leaks in the core
* Remove unused NAND locking support
* Rename nand.h into rawnand.h (preparing support for spi NANDs)
* Use NAND_MAX_ID_LEN where appropriate
* Fix support for 20nm Hynix chips
* Fix support for Samsung and Hynix SLC NANDs
and the following driver changes:
* Various cleanup, improvements and fixes in the qcom driver
* Fixes for bugs detected by various static code analysis tools
* Fix mxc ooblayout definition
* Add a new part_parsers to tmio and sharpsl platform data in order to
define a custom list of partition parsers
* Request the reset line in exclusive mode in the sunxi driver
* Fix a build error in the orion-nand driver when compiled for ARMv4
* Allow 64-bit mvebu platforms to select the PXA3XX driver
"
|
|
From Cyrille:
"
This pull request contains the following notable changes:
- add support to the JEDEC JESD216B specification (SFDP tables).
- add support to the Intel Denverton SPI flash controller.
- fix error recovery for Spansion/Cypress SPI NOR memories.
- fix 4-byte address management for the Aspeed SPI controller.
- add support to some Microchip SST26 memory parts
- remove unneeded pinctrl header
"
|
|
chip->bits_per_cell which is used to determine the NAND cell type
(SLC/MLC) should always have a value != 0.
Complain loudly if the value is 0 in nand_is_slc() to catch use before
correct initialization.
Signed-off-by: Lothar Waßmann <[email protected]>
Signed-off-by: Boris Brezillon <[email protected]>
|
|
Merge v4.13-rc7 back to resolve merge conflicts in
drivers/mtd/nand/nandsim.c and include/asm-generic/vmlinux.lds.h.
|
|
into nand/next
|
|
With the introduction of sharpslpart partition parser we can now read the
offsets from NAND: we specify the list of the parsers as platform data, with
cmdlinepart and ofpart parsers first allowing to override the part. table
written in NAND. This is done in the board files using this driver.
Thus, we need to extend sharpsl_nand_platform_data to consider the partition
parsers.
Signed-off-by: Andrea Adami <[email protected]>
Signed-off-by: Boris Brezillon <[email protected]>
|
|
This commit removes hard-coded '8' used for looping into
struct nand_chip.id.data array.
NAND_MAX_ID_LEN has been introduced by Artem Bityutskiy in
53552d22bfe1f for defining ids length in nand_flash_ids[] list.
This commit unifies ids length in nand base driver.
Signed-off-by: Jean-Louis Thekekara <[email protected]>
Signed-off-by: Boris Brezillon <[email protected]>
|
|
When XIP_KERNEL is enabled, some functions are defined in the .data
ELF section because we require them to be in RAM whenever we communicate
with the flash chip. However this causes problems when FTRACE is
enabled and gcc emits calls to __gnu_mcount_nc in the function
prolog:
drivers/built-in.o: In function `cfi_chip_setup':
:(.data+0x272fc): relocation truncated to fit: R_ARM_CALL against symbol `__gnu_mcount_nc' defined in .text section in arch/arm/kernel/built-in.o
drivers/built-in.o: In function `cfi_probe_chip':
:(.data+0x27de8): relocation truncated to fit: R_ARM_CALL against symbol `__gnu_mcount_nc' defined in .text section in arch/arm/kernel/built-in.o
/tmp/ccY172rP.s: Assembler messages:
/tmp/ccY172rP.s:70: Warning: ignoring changed section attributes for .data
/tmp/ccY172rP.s: Error: 1 warning, treating warnings as errors
make[5]: *** [drivers/mtd/chips/cfi_probe.o] Error 1
/tmp/ccK4rjeO.s: Assembler messages:
/tmp/ccK4rjeO.s:421: Warning: ignoring changed section attributes for .data
/tmp/ccK4rjeO.s: Error: 1 warning, treating warnings as errors
make[5]: *** [drivers/mtd/chips/cfi_util.o] Error 1
/tmp/ccUvhCYR.s: Assembler messages:
/tmp/ccUvhCYR.s:1895: Warning: ignoring changed section attributes for .data
/tmp/ccUvhCYR.s: Error: 1 warning, treating warnings as errors
Specifically, this does not work because the .data section is not
marked executable, which leads LD to not generate trampolines for
long calls.
This moves the __xipram functions into their own .xiptext section instead.
The section is still placed next to .data and located in RAM but is marked
executable, which avoids the build errors.
Also, we only need to place the XIP functions into a separate section
if both CONFIG_XIP_KERNEL and CONFIG_MTD_XIP are set: When only MTD_XIP
is used, the whole kernel is still in RAM and we do not need to worry
about pulling out the rug under it. When only XIP_KERNEL but not MTD_XIP
is set, the kernel is in some form of ROM, but we never write to it.
Note that MTD_XIP has been broken on ARM since around 2011 or 2012. I
have sent another patch[2] to fix compilation, which I plan to merge
through arm-soc unless there are objections. The obvious alternative
to that would be to completely rip out the MTD_XIP support from the
kernel, since obviously nobody has been using it in a long while.
Link: [1] https://patchwork.kernel.org/patch/8109771/
Link: [2] https://patchwork.kernel.org/patch/9855225/
Signed-off-by: Arnd Bergmann <[email protected]>
Signed-off-by: Boris Brezillon <[email protected]>
|
|
We are planning to share more code between different NAND based
devices (SPI NAND, OneNAND and raw NANDs), but before doing that
we need to move the existing include/linux/mtd/nand.h file into
include/linux/mtd/rawnand.h so we can later create a nand.h header
containing all common structure and function prototypes.
Signed-off-by: Boris Brezillon <[email protected]>
Signed-off-by: Peter Pan <[email protected]>
Acked-by: Vladimir Zapolskiy <[email protected]>
Acked-by: Alexander Sverdlin <[email protected]>
Acked-by: Wenyou Yang <[email protected]>
Acked-by: Krzysztof Kozlowski <[email protected]>
Acked-by: Han Xu <[email protected]>
Acked-by: H Hartley Sweeten <[email protected]>
Acked-by: Shawn Guo <[email protected]>
Acked-by: Gregory CLEMENT <[email protected]>
Acked-by: Neil Armstrong <[email protected]>
Acked-by: Masahiro Yamada <[email protected]>
Acked-By: Harvey Hunt <[email protected]>
Acked-by: Tony Lindgren <[email protected]>
Acked-by: Krzysztof Halasa <[email protected]>
|
|
Commit 7d70f334ad2b ("mtd: nand: add lock/unlock routines") introduced
support for the Micron LOCK/UNLOCK commands but no one ever used the
nand_lock/unlock() functions.
Remove support for these vendor-specific operations from the core. If
one ever wants to add them back they should be put in nand_micron.c and
mtd->_lock/_unlock should be directly assigned from there instead of
exporting the functions.
Signed-off-by: Boris Brezillon <[email protected]>
|
|
All timings in nand_sdr_timings are expressed in picoseconds but some
of them may not fit in an u32.
Signed-off-by: Boris Brezillon <[email protected]>
Fixes: 204e7ecd47e2 ("mtd: nand: Add a few more timings to nand_sdr_timings")
Reported-by: Alexander Dahl <[email protected]>
Cc: <[email protected]>
Reviewed-by: Alexander Dahl <[email protected]>
Tested-by: Alexander Dahl <[email protected]>
Signed-off-by: Boris Brezillon <[email protected]>
|
|
S25FL{128|256|512}S datasheets say:
"When P_ERR or E_ERR bits are set to one, the WIP bit will remain set to
one indicating the device remains busy and unable to receive new operation
commands. A Clear Status Register (CLSR) command must be received to return
the device to standby mode."
Current spi-nor code works until first error occurs, but write/erase errors
are not just rare hardware failures, they also occur if user tries to flash
write-protected areas. After such attempt no SPI command can be executed
any more and even read fails. This patch adds support for P_ERR and E_ERR
bits in Status Register 1 (so that operation fails immediately and not
after a long timeout) and proper recovery from the error condition.
Tested on Spansion S25FS128S, which is supported by S25FL129P entry.
Signed-off-by: Alexander Sverdlin <[email protected]>
Signed-off-by: Cyrille Pitchen <[email protected]>
|
|
Several MTD devices are using debugfs entries created in the root.
This commit provides the means for a standardized subtree, creating
one "mtd" entry at root, and one entry per device inside it, named
after the device.
The tree is registered in add_mtd_device, and released in
del_mtd_device.
Devices docg3, mtdswap and nandsim were updated to use this subtree
instead of custom ones, and their entries were prefixed with the
drivers' names.
Signed-off-by: Mario J. Rugiero <[email protected]>
Acked-by: Boris Brezillon <[email protected]>
Signed-off-by: Brian Norris <[email protected]>
|