| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Most modern hardware supports very fast accelerated crc32c calculation.
If that is supported the CPU overhead of the checksum calculation is
very limited, and offloading the calculation to special worker threads
has a lot of overhead for no gain.
E.g. on an Intel Optane device is actually very much slows down even
1M buffered writes with fio:
Unpatched:
write: IOPS=3316, BW=3316MiB/s (3477MB/s)(200GiB/61757msec); 0 zone resets
With synchronous CRCs:
write: IOPS=4882, BW=4882MiB/s (5119MB/s)(200GiB/41948msec); 0 zone resets
With a lot of variation during the unpatched run going down as low as
1100MB/s, while the synchronous CRC version has about the same peak write
speed but much lower dips, and fewer kworkers churning around.
Both tests had fio saturated at 100% CPU.
(thanks to Jens Axboe via Chris Mason for the benchmarking)
Reviewed-by: Chris Mason <clm@fb.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Using SECTOR_SHIFT to convert LBA to physical address makes it more
readable.
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Use SECTOR_SHIFT while converting a physical address to an LBA, makes
it more readable.
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Improve the leaf dump behavior by:
- Always dump the leaf first, then the error message
- Output the slot number if possible
Especially in __btrfs_free_extent() the leaf dump of extent tree can
be pretty large.
With an extra slot number it's much easier to locate the problem.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Since print-tree infrastructure only prints the content of a tree block,
we can make them to accept const extent buffer pointer.
This removes a forced type convert in extent-tree, where we convert a
const extent buffer pointer to regular one, just to avoid compiler
warning.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
bitmap_test_range_all_{set,zero} defined in subpage.c are useful for other
components. Move them to misc.h and use them in zoned.c. Also, as
find_next{,_zero}_bit take/return "unsigned long" instead of "unsigned
int", convert the type to "unsigned long".
While at it, also rewrite the "if (...) return true; else return false;"
pattern and add const to the input bitmap.
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
When checking siblings keys, before moving keys from one node/leaf to a
sibling node/leaf, it's very unexpected to have the last key of the left
sibling greater than or equals to the first key of the right sibling, as
that means we have a (serious) corruption that breaks the key ordering
properties of a b+tree. Since this is unexpected, surround the comparison
with the unlikely macro, which helps the compiler generate better code
for the most expected case (no existing b+tree corruption). This is also
what we do for other unexpected cases of invalid key ordering (like at
btrfs_set_item_key_safe()).
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
The function btrfs_free_device() is never used outside of volumes.c, so
make it static and remove its prototype declaration at volumes.h.
Reviewed-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Recently a Meta-internal workload encountered subvolume creation taking
up to 2s each, significantly slower than directory creation. As they
were hoping to be able to use subvolumes instead of directories, and
were looking to create hundreds, this was a significant issue. After
Josef investigated, it turned out to be due to the transaction commit
currently performed at the end of subvolume creation.
This change improves the workload by not doing transaction commit for every
subvolume creation, and merely requiring a transaction commit on fsync.
In the worst case, of doing a subvolume create and fsync in a loop, this
should require an equal amount of time to the current scheme; and in the
best case, the internal workload creating hundreds of subvolumes before
fsyncing is greatly improved.
While it would be nice to be able to use the log tree and use the normal
fsync path, log tree replay can't deal with new subvolume inodes
presently.
It's possible that there's some reason that the transaction commit is
necessary for correctness during subvolume creation; however,
git logs indicate that the commit dates back to the beginning of
subvolume creation, and there are no notes on why it would be necessary.
Reviewed-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Sweet Tea Dorminy <sweettea-kernel@dorminy.me>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
btrfs_prev_leaf() is not used outside ctree.c, so there's no need to
export it at ctree.h - just make it static at ctree.c and move its
definition above btrfs_search_slot_for_read(), since that function
calls it.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
In the same spirit as commit ca57f02295f1 ("afs: Fix fileserver probe
RTT handling"), don't rule out using a vlserver just because there
haven't been enough packets yet to calculate a real rtt. Always set the
server's probe rtt from the estimate provided by rxrpc_kernel_get_srtt,
which is capped at 1 second.
This could lead to EDESTADDRREQ errors when accessing a cell for the
first time, even though the vl servers are known and have responded to a
probe.
Fixes: 1d4adfaf6574 ("rxrpc: Make rxrpc_kernel_get_srtt() indicate validity")
Signed-off-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: linux-afs@lists.infradead.org
Link: http://lists.infradead.org/pipermail/linux-afs/2023-June/006746.html
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"Two fixes for NOCOW files, a regression fix in scrub and an assertion
fix:
- NOCOW fixes:
- keep length of iomap direct io request in case of a failure
- properly pass mode of extent reference checking, this can break
some cases for swapfile
- fix error value confusion when scrubbing a stripe
- convert assertion to a proper error handling when loading global
roots, reported by syzbot"
* tag 'for-6.4-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: scrub: fix a return value overwrite in scrub_stripe()
btrfs: do not ASSERT() on duplicated global roots
btrfs: can_nocow_file_extent should pass down args->strict from callers
btrfs: fix iomap_begin length for nocow writes
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"Fix two regressions in ext4, one report by syzkaller[1], and reported
by multiple users (and tracked by regzbot[2])"
[1] https://syzkaller.appspot.com/bug?extid=4acc7d910e617b360859
[2] https://linux-regtracking.leemhuis.info/regzbot/regression/ZIauBR7YiV3rVAHL@glitch/
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: drop the call to ext4_error() from ext4_get_group_info()
Revert "ext4: remove unnecessary check in ext4_bg_num_gdb_nometa"
|
|
Pull smb client fixes from Steve French:
"Eight, mostly small, smb3 client fixes:
- important fix for deferred close oops (race with unmount) found
with xfstest generic/098 to some servers
- important reconnect fix
- fix problem with max_credits mount option
- two multichannel (interface related) fixes
- one trivial removal of confusing comment
- two small debugging improvements (to better spot crediting
problems)"
* tag '6.4-rc6-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: add a warning when the in-flight count goes negative
cifs: fix lease break oops in xfstest generic/098
cifs: fix max_credits implementation
cifs: fix sockaddr comparison in iface_cmp
smb/client: print "Unknown" instead of bogus link speed value
cifs: print all credit counters in DebugData
cifs: fix status checks in cifs_tree_connect
smb: remove obsolete comment
|
|
A recent patch added a call to ext4_error() which is problematic since
some callers of the ext4_get_group_info() function may be holding a
spinlock, whereas ext4_error() must never be called in atomic context.
This triggered a report from Syzbot: "BUG: sleeping function called from
invalid context in ext4_update_super" (see the link below).
Therefore, drop the call to ext4_error() from ext4_get_group_info(). In
the meantime use eight characters tabs instead of nine characters ones.
Reported-by: syzbot+4acc7d910e617b360859@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/all/00000000000070575805fdc6cdb2@google.com/
Fixes: 5354b2af3406 ("ext4: allow ext4_get_group_info() to fail")
Suggested-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Fabio M. De Francesco <fmdefrancesco@gmail.com>
Link: https://lore.kernel.org/r/20230614100446.14337-1-fmdefrancesco@gmail.com
|
|
This reverts commit ad3f09be6cfe332be8ff46c78e6ec0f8839107aa.
The reverted commit was intended to simpfy the code to get group
descriptor block number in non-meta block group by assuming
s_gdb_count is block number used for all non-meta block group descriptors.
However s_gdb_count is block number used for all meta *and* non-meta
group descriptors. So s_gdb_group will be > actual group descriptor block
number used for all non-meta block group which should be "total non-meta
block group" / "group descriptors per block", e.g. s_first_meta_bg.
Signed-off-by: Kemeng Shi <shikemeng@huaweicloud.com>
Link: https://lore.kernel.org/r/20230613225025.3859522-1-shikemeng@huaweicloud.com
Fixes: ad3f09be6cfe ("ext4: remove unnecessary check in ext4_bg_num_gdb_nometa")
Cc: stable@kernel.org
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
[RETURN VALUE OVERWRITE]
Inside scrub_stripe(), we would submit all the remaining stripes after
iterating all extents.
But since flush_scrub_stripes() can return error, we need to avoid
overwriting the existing @ret if there is any error.
However the existing check is doing the wrong check:
ret2 = flush_scrub_stripes();
if (!ret2)
ret = ret2;
This would overwrite the existing @ret to 0 as long as the final flush
detects no critical errors.
[FIX]
We should check @ret other than @ret2 in that case.
Fixes: 8eb3dd17eadd ("btrfs: dev-replace: error out if we have unrepaired metadata error during")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
We've seen the in-flight count go into negative with some
internal stress testing in Microsoft.
Adding a WARN when this happens, in hope of understanding
why this happens when it happens.
Signed-off-by: Shyam Prasad N <sprasad@microsoft.com>
Reviewed-by: Bharath SM <bharathsm@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
umount can race with lease break so need to check if
tcon->ses->server is still valid to send the lease
break response.
Reviewed-by: Bharath SM <bharathsm@microsoft.com>
Reviewed-by: Shyam Prasad N <sprasad@microsoft.com>
Fixes: 59a556aebc43 ("SMB3: drop reference to cfile before sending oplock break")
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
[BUG]
Syzbot reports a reproducible ASSERT() when using rescue=usebackuproot
mount option on a corrupted fs.
The full report can be found here:
https://syzkaller.appspot.com/bug?extid=c4614eae20a166c25bf0
BTRFS error (device loop0: state C): failed to load root csum
assertion failed: !tmp, in fs/btrfs/disk-io.c:1103
------------[ cut here ]------------
kernel BUG at fs/btrfs/ctree.h:3664!
invalid opcode: 0000 [#1] PREEMPT SMP KASAN
CPU: 1 PID: 3608 Comm: syz-executor356 Not tainted 6.0.0-rc7-syzkaller-00029-g3800a713b607 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 08/26/2022
RIP: 0010:assertfail+0x1a/0x1c fs/btrfs/ctree.h:3663
RSP: 0018:ffffc90003aaf250 EFLAGS: 00010246
RAX: 0000000000000032 RBX: 0000000000000000 RCX: f21c13f886638400
RDX: 0000000000000000 RSI: 0000000080000000 RDI: 0000000000000000
RBP: ffff888021c640a0 R08: ffffffff816bd38d R09: ffffed10173667f1
R10: ffffed10173667f1 R11: 1ffff110173667f0 R12: dffffc0000000000
R13: ffff8880229c21f7 R14: ffff888021c64060 R15: ffff8880226c0000
FS: 0000555556a73300(0000) GS:ffff8880b9b00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000055a2637d7a00 CR3: 00000000709c4000 CR4: 00000000003506e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
btrfs_global_root_insert+0x1a7/0x1b0 fs/btrfs/disk-io.c:1103
load_global_roots_objectid+0x482/0x8c0 fs/btrfs/disk-io.c:2467
load_global_roots fs/btrfs/disk-io.c:2501 [inline]
btrfs_read_roots fs/btrfs/disk-io.c:2528 [inline]
init_tree_roots+0xccb/0x203c fs/btrfs/disk-io.c:2939
open_ctree+0x1e53/0x33df fs/btrfs/disk-io.c:3574
btrfs_fill_super+0x1c6/0x2d0 fs/btrfs/super.c:1456
btrfs_mount_root+0x885/0x9a0 fs/btrfs/super.c:1824
legacy_get_tree+0xea/0x180 fs/fs_context.c:610
vfs_get_tree+0x88/0x270 fs/super.c:1530
fc_mount fs/namespace.c:1043 [inline]
vfs_kern_mount+0xc9/0x160 fs/namespace.c:1073
btrfs_mount+0x3d3/0xbb0 fs/btrfs/super.c:1884
[CAUSE]
Since the introduction of global roots, we handle
csum/extent/free-space-tree roots as global roots, even if no
extent-tree-v2 feature is enabled.
So for regular csum/extent/fst roots, we load them into
fs_info::global_root_tree rb tree.
And we should not expect any conflicts in that rb tree, thus we have an
ASSERT() inside btrfs_global_root_insert().
But rescue=usebackuproot can break the assumption, as we will try to
load those trees again and again as long as we have bad roots and have
backup roots slot remaining.
So in that case we can have conflicting roots in the rb tree, and
triggering the ASSERT() crash.
[FIX]
We can safely remove that ASSERT(), as the caller will properly put the
offending root.
To make further debugging easier, also add two explicit error messages:
- Error message for conflicting global roots
- Error message when using backup roots slot
Reported-by: syzbot+a694851c6ab28cbcfb9c@syzkaller.appspotmail.com
Fixes: abed4aaae4f7 ("btrfs: track the csum, extent, and free space trees in a rb tree")
CC: stable@vger.kernel.org # 6.1+
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc fixes from Andrew Morton:
"19 hotfixes. 14 are cc:stable and the remainder address issues which
were introduced during this development cycle or which were considered
inappropriate for a backport"
* tag 'mm-hotfixes-stable-2023-06-12-12-22' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
zswap: do not shrink if cgroup may not zswap
page cache: fix page_cache_next/prev_miss off by one
ocfs2: check new file size on fallocate call
mailmap: add entry for John Keeping
mm/damon/core: fix divide error in damon_nr_accesses_to_accesses_bp()
epoll: ep_autoremove_wake_function should use list_del_init_careful
mm/gup_test: fix ioctl fail for compat task
nilfs2: reject devices with insufficient block count
ocfs2: fix use-after-free when unmounting read-only filesystem
lib/test_vmalloc.c: avoid garbage in page array
nilfs2: fix possible out-of-bounds segment allocation in resize ioctl
riscv/purgatory: remove PGO flags
powerpc/purgatory: remove PGO flags
x86/purgatory: remove PGO flags
kexec: support purgatories with .text.hot sections
mm/uffd: allow vma to merge as much as possible
mm/uffd: fix vma operation where start addr cuts part of vma
radix-tree: move declarations to header
nilfs2: fix incomplete buffer cleanup in nilfs_btnode_abort_change_key()
|
|
Commit 619104ba453ad0 ("btrfs: move common NOCOW checks against a file
extent into a helper") changed our call to btrfs_cross_ref_exist() to
always pass false for the 'strict' parameter. We're passing this down
through the stack so that we can do a full check for cross references
during swapfile activation.
With strict always false, this test fails:
btrfs subvol create swappy
chattr +C swappy
fallocate -l1G swappy/swapfile
chmod 600 swappy/swapfile
mkswap swappy/swapfile
btrfs subvol snap swappy swapsnap
btrfs subvol del -C swapsnap
btrfs fi sync /
sync;sync;sync
swapon swappy/swapfile
The fix is to just use args->strict, and everyone except swapfile
activation is passing false.
Fixes: 619104ba453ad0 ("btrfs: move common NOCOW checks against a file extent into a helper")
CC: stable@vger.kernel.org # 6.1+
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
can_nocow_extent can reduce the len passed in, which needs to be
propagated to btrfs_dio_iomap_begin so that iomap does not submit
more data then is mapped.
This problems exists since the btrfs_get_blocks_direct helper was added
in commit c5794e51784a ("btrfs: Factor out write portion of
btrfs_get_blocks_direct"), but the ordered_extent splitting added in
commit b73a6fd1b1ef ("btrfs: split partial dio bios before submit")
added a WARN_ON that made a syzkaller test fail.
Reported-by: syzbot+ee90502d5c8fd1d0dd93@syzkaller.appspotmail.com
Fixes: c5794e51784a ("btrfs: Factor out write portion of btrfs_get_blocks_direct")
CC: stable@vger.kernel.org # 6.1+
Tested-by: syzbot+ee90502d5c8fd1d0dd93@syzkaller.appspotmail.com
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
When changing a file size with fallocate() the new size isn't being
checked. In particular, the FSIZE ulimit isn't being checked, which makes
fstest generic/228 fail. Simply adding a call to inode_newsize_ok() fixes
this issue.
Link: https://lkml.kernel.org/r/20230529152645.32680-1-lhenriques@suse.de
Signed-off-by: Luís Henriques <lhenriques@suse.de>
Reviewed-by: Mark Fasheh <mark@fasheh.com>
Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Changwei Ge <gechangwei@live.cn>
Cc: Gang He <ghe@suse.com>
Cc: Jun Piao <piaojun@huawei.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
autoremove_wake_function uses list_del_init_careful, so should epoll's
more aggressive variant. It only doesn't because it was copied from an
older wait.c rather than the most recent.
[bsegall@google.com: add comment]
Link: https://lkml.kernel.org/r/xm26bki0ulsr.fsf_-_@google.com
Link: https://lkml.kernel.org/r/xm26pm6hvfer.fsf@google.com
Fixes: a16ceb139610 ("epoll: autoremove wakers even more aggressively")
Signed-off-by: Ben Segall <bsegall@google.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christian Brauner <brauner@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
The current sanity check for nilfs2 geometry information lacks checks for
the number of segments stored in superblocks, so even for device images
that have been destructively truncated or have an unusually high number of
segments, the mount operation may succeed.
This causes out-of-bounds block I/O on file system block reads or log
writes to the segments, the latter in particular causing
"a_ops->writepages" to repeatedly fail, resulting in sync_inodes_sb() to
hang.
Fix this issue by checking the number of segments stored in the superblock
and avoiding mounting devices that can cause out-of-bounds accesses. To
eliminate the possibility of overflow when calculating the number of
blocks required for the device from the number of segments, this also adds
a helper function to calculate the upper bound on the number of segments
and inserts a check using it.
Link: https://lkml.kernel.org/r/20230526021332.3431-1-konishi.ryusuke@gmail.com
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Reported-by: syzbot+7d50f1e54a12ba3aeae2@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?extid=7d50f1e54a12ba3aeae2
Tested-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
It's trivial to trigger a use-after-free bug in the ocfs2 quotas code using
fstest generic/452. After a read-only remount, quotas are suspended and
ocfs2_mem_dqinfo is freed through ->ocfs2_local_free_info(). When unmounting
the filesystem, an UAF access to the oinfo will eventually cause a crash.
BUG: KASAN: slab-use-after-free in timer_delete+0x54/0xc0
Read of size 8 at addr ffff8880389a8208 by task umount/669
...
Call Trace:
<TASK>
...
timer_delete+0x54/0xc0
try_to_grab_pending+0x31/0x230
__cancel_work_timer+0x6c/0x270
ocfs2_disable_quotas.isra.0+0x3e/0xf0 [ocfs2]
ocfs2_dismount_volume+0xdd/0x450 [ocfs2]
generic_shutdown_super+0xaa/0x280
kill_block_super+0x46/0x70
deactivate_locked_super+0x4d/0xb0
cleanup_mnt+0x135/0x1f0
...
</TASK>
Allocated by task 632:
kasan_save_stack+0x1c/0x40
kasan_set_track+0x21/0x30
__kasan_kmalloc+0x8b/0x90
ocfs2_local_read_info+0xe3/0x9a0 [ocfs2]
dquot_load_quota_sb+0x34b/0x680
dquot_load_quota_inode+0xfe/0x1a0
ocfs2_enable_quotas+0x190/0x2f0 [ocfs2]
ocfs2_fill_super+0x14ef/0x2120 [ocfs2]
mount_bdev+0x1be/0x200
legacy_get_tree+0x6c/0xb0
vfs_get_tree+0x3e/0x110
path_mount+0xa90/0xe10
__x64_sys_mount+0x16f/0x1a0
do_syscall_64+0x43/0x90
entry_SYSCALL_64_after_hwframe+0x72/0xdc
Freed by task 650:
kasan_save_stack+0x1c/0x40
kasan_set_track+0x21/0x30
kasan_save_free_info+0x2a/0x50
__kasan_slab_free+0xf9/0x150
__kmem_cache_free+0x89/0x180
ocfs2_local_free_info+0x2ba/0x3f0 [ocfs2]
dquot_disable+0x35f/0xa70
ocfs2_susp_quotas.isra.0+0x159/0x1a0 [ocfs2]
ocfs2_remount+0x150/0x580 [ocfs2]
reconfigure_super+0x1a5/0x3a0
path_mount+0xc8a/0xe10
__x64_sys_mount+0x16f/0x1a0
do_syscall_64+0x43/0x90
entry_SYSCALL_64_after_hwframe+0x72/0xdc
Link: https://lkml.kernel.org/r/20230522102112.9031-1-lhenriques@suse.de
Signed-off-by: Luís Henriques <lhenriques@suse.de>
Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Tested-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Changwei Ge <gechangwei@live.cn>
Cc: Gang He <ghe@suse.com>
Cc: Jun Piao <piaojun@huawei.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Syzbot reports that in its stress test for resize ioctl, the log writing
function nilfs_segctor_do_construct hits a WARN_ON in
nilfs_segctor_truncate_segments().
It turned out that there is a problem with the current implementation of
the resize ioctl, which changes the writable range on the device (the
range of allocatable segments) at the end of the resize process.
This order is necessary for file system expansion to avoid corrupting the
superblock at trailing edge. However, in the case of a file system
shrink, if log writes occur after truncating out-of-bounds trailing
segments and before the resize is complete, segments may be allocated from
the truncated space.
The userspace resize tool was fine as it limits the range of allocatable
segments before performing the resize, but it can run into this issue if
the resize ioctl is called alone.
Fix this issue by changing nilfs_sufile_resize() to update the range of
allocatable segments immediately after successful truncation of segment
space in case of file system shrink.
Link: https://lkml.kernel.org/r/20230524094348.3784-1-konishi.ryusuke@gmail.com
Fixes: 4e33f9eab07e ("nilfs2: implement resize ioctl")
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Reported-by: syzbot+33494cd0df2ec2931851@syzkaller.appspotmail.com
Closes: https://lkml.kernel.org/r/0000000000005434c405fbbafdc5@google.com
Tested-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
We used to not pass in the pgoff correctly when register/unregister uffd
regions, it caused incorrect behavior on vma merging and can cause
mergeable vmas being separate after ioctls return.
For example, when we have:
vma1(range 0-9, with uffd), vma2(range 10-19, no uffd)
Then someone unregisters uffd on range (5-9), it should logically become:
vma1(range 0-4, with uffd), vma2(range 5-19, no uffd)
But with current code we'll have:
vma1(range 0-4, with uffd), vma3(range 5-9, no uffd), vma2(range 10-19, no uffd)
This patch allows such merge to happen correctly before ioctl returns.
This behavior seems to have existed since the 1st day of uffd. Since
pgoff for vma_merge() is only used to identify the possibility of vma
merging, meanwhile here what we did was always passing in a pgoff smaller
than what we should, so there should have no other side effect besides not
merging it. Let's still tentatively copy stable for this, even though I
don't see anything will go wrong besides vma being split (which is mostly
not user visible).
Link: https://lkml.kernel.org/r/20230517190916.3429499-3-peterx@redhat.com
Fixes: 86039bd3b4e6 ("userfaultfd: add new syscall to provide memory externalization")
Signed-off-by: Peter Xu <peterx@redhat.com>
Reported-by: Lorenzo Stoakes <lstoakes@gmail.com>
Acked-by: Lorenzo Stoakes <lstoakes@gmail.com>
Reviewed-by: Liam R. Howlett <Liam.Howlett@oracle.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Mike Rapoport (IBM) <rppt@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Patch series "mm/uffd: Fix vma merge/split", v2.
This series contains two patches that fix vma merge/split for userfaultfd
on two separate issues.
Patch 1 fixes a regression since 6.1+ due to something we overlooked when
converting to maple tree apis. The plan is we use patch 1 to replace the
commit "2f628010799e (mm: userfaultfd: avoid passing an invalid range to
vma_merge())" in mm-hostfixes-unstable tree if possible, so as to bring
uffd vma operations back aligned with the rest code again.
Patch 2 fixes a long standing issue that vma can be left unmerged even if
we can for either uffd register or unregister.
Many thanks to Lorenzo on either noticing this issue from the assert
movement patch, looking at this problem, and also provided a reproducer on
the unmerged vma issue [1].
[1] https://gist.github.com/lorenzo-stoakes/a11a10f5f479e7a977fc456331266e0e
This patch (of 2):
It seems vma merging with uffd paths is broken with either
register/unregister, where right now we can feed wrong parameters to
vma_merge() and it's found by recent patch which moved asserts upwards in
vma_merge() by Lorenzo Stoakes:
https://lore.kernel.org/all/ZFunF7DmMdK05MoF@FVFF77S0Q05N.cambridge.arm.com/
It's possible that "start" is contained within vma but not clamped to its
start. We need to convert this into either "cannot merge" case or "can
merge" case 4 which permits subdivision of prev by assigning vma to prev.
As we loop, each subsequent VMA will be clamped to the start.
This patch will eliminate the report and make sure vma_merge() calls will
become legal again.
One thing to mention is that the "Fixes: 29417d292bd0" below is there only
to help explain where the warning can start to trigger, the real commit to
fix should be 69dbe6daf104. Commit 29417d292bd0 helps us to identify the
issue, but unfortunately we may want to keep it in Fixes too just to ease
kernel backporters for easier tracking.
Link: https://lkml.kernel.org/r/20230517190916.3429499-1-peterx@redhat.com
Link: https://lkml.kernel.org/r/20230517190916.3429499-2-peterx@redhat.com
Fixes: 69dbe6daf104 ("userfaultfd: use maple tree iterator to iterate VMAs")
Signed-off-by: Peter Xu <peterx@redhat.com>
Reported-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com>
Reviewed-by: Liam R. Howlett <Liam.Howlett@oracle.com>
Closes: https://lore.kernel.org/all/ZFunF7DmMdK05MoF@FVFF77S0Q05N.cambridge.arm.com/
Cc: Lorenzo Stoakes <lstoakes@gmail.com>
Cc: Mike Rapoport (IBM) <rppt@kernel.org>
Cc: Liam R. Howlett <Liam.Howlett@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
A syzbot fault injection test reported that nilfs_btnode_create_block, a
helper function that allocates a new node block for b-trees, causes a
kernel BUG for disk images where the file system block size is smaller
than the page size.
This was due to unexpected flags on the newly allocated buffer head, and
it turned out to be because the buffer flags were not cleared by
nilfs_btnode_abort_change_key() after an error occurred during a b-tree
update operation and the buffer was later reused in that state.
Fix this issue by using nilfs_btnode_delete() to abandon the unused
preallocated buffer in nilfs_btnode_abort_change_key().
Link: https://lkml.kernel.org/r/20230513102428.10223-1-konishi.ryusuke@gmail.com
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Reported-by: syzbot+b0a35a5c1f7e846d3b09@syzkaller.appspotmail.com
Closes: https://lkml.kernel.org/r/000000000000d1d6c205ebc4d512@google.com
Tested-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"A more fixes and regression fixes:
- in subpage mode, fix crash when repairing metadata at the end of
a stripe
- properly enable async discard when remounting from read-only to
read-write
- scrub regression fixes:
- respect read-only scrub when attempting to do a repair
- fix reporting of found errors, the stats don't get properly
accounted after a stripe repair"
* tag 'for-6.4-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: scrub: also report errors hit during the initial read
btrfs: scrub: respect the read-only flag during repair
btrfs: properly enable async discard when switching from RO->RW
btrfs: subpage: fix a crash in metadata repair path
|
|
The current implementation of max_credits on the client does
not work because the CreditRequest logic for several commands
does not take max_credits into account.
Still, we can end up asking the server for more credits, depending
on the number of credits in flight. For this, we need to
limit the credits while parsing the responses too.
Signed-off-by: Shyam Prasad N <sprasad@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
iface_cmp used to simply do a memcmp of the two
provided struct sockaddrs. The comparison needs to do more
based on the address family. Similar logic was already
present in cifs_match_ipaddr. Doing something similar now.
Signed-off-by: Shyam Prasad N <sprasad@microsoft.com>
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
The virtio driver for Linux guests will not set a link speed to its
paravirtualized NICs. This will be seen as -1 in the ethernet layer, and
when some servers (e.g. samba) fetches it, it's converted to an unsigned
value (and multiplied by 1000 * 1000), so in client side we end up with:
1) Speed: 4294967295000000 bps
in DebugData.
This patch introduces a helper that returns a speed string (in Mbps or
Gbps) if interface speed is valid (>= SPEED_10 and <= SPEED_800000), or
"Unknown" otherwise.
The reason to not change the value in iface->speed is because we don't
know the real speed of the HW backing the server NIC, so let's keep
considering these as the fastest NICs available.
Also print "Capabilities: None" when the interface doesn't support any.
Signed-off-by: Enzo Matsumiya <ematsumiya@suse.de>
Reviewed-by: Shyam Prasad N <sprasad@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
Output of /proc/fs/cifs/DebugData shows only the per-connection
counter for the number of credits of regular type. i.e. the
credits reserved for echo and oplocks are not displayed.
There have been situations recently where having this info
would have been useful. This change prints the credit counters
of all three types: regular, echo, oplocks.
Signed-off-by: Shyam Prasad N <sprasad@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
The ordering of status checks at the beginning of
cifs_tree_connect is wrong. As a result, a tcon
which is good may stay marked as needing reconnect
infinitely.
Fixes: 2f0e4f034220 ("cifs: check only tcon status on tcon related functions")
Cc: stable@vger.kernel.org # 6.3
Signed-off-by: Shyam Prasad N <sprasad@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
Because do_gettimeofday has been removed and replaced by ktime_get_real_ts64,
So just remove the comment as it's not needed now.
Signed-off-by: 鑫华 <jixianghua@xfusion.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
Pull smb server fixes from Steve French:
"Five smb3 server fixes, all also for stable:
- Fix four slab out of bounds warnings: improve checks for protocol
id, and for small packet length, and for create context parsing,
and for negotiate context parsing
- Fix for incorrect dereferencing POSIX ACLs"
* tag '6.4-rc5-smb3-server-fixes' of git://git.samba.org/ksmbd:
ksmbd: validate smb request protocol id
ksmbd: check the validation of pdu_size in ksmbd_conn_handler_loop
ksmbd: fix posix_acls and acls dereferencing possible ERR_PTR()
ksmbd: fix out-of-bound read in parse_lease_state()
ksmbd: fix out-of-bound read in deassemble_neg_contexts()
|
|
Pull ceph fixes from Ilya Dryomov:
"A fix for a potential data corruption in differential backup and
snapshot-based mirroring scenarios in RBD and a reference counting
fixup to avoid use-after-free in CephFS, all marked for stable"
* tag 'ceph-for-6.4-rc6' of https://github.com/ceph/ceph-client:
ceph: fix use-after-free bug for inodes when flushing capsnaps
rbd: get snapshot context after exclusive lock is ensured to be held
rbd: move RBD_OBJ_FLAG_COPYUP_ENABLED flag setting
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 fix from Ted Ts'o:
"Fix an ext4 regression which breaks remounting r/w file systems that
have the quota feature enabled"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: only check dquot_initialize_needed() when debugging
Revert "ext4: don't clear SB_RDONLY when remounting r/w until quota is re-enabled"
|
|
Pull xfs fixes from Dave Chinner:
"These are a set of regression fixes discovered on recent kernels. I
was hoping to send this to you a week and half ago, but events out of
my control delayed finalising the changes until early this week.
Whilst the diffstat looks large for this stage of the merge window, a
large chunk of it comes from moving the guts of one function from one
file to another i.e. it's the same code, it is just run in a different
context where it is safe to hold a specific lock. Otherwise the
individual changes are relatively small and straigtht forward.
Summary:
- Propagate unlinked inode list corruption back up to log recovery
(regression fix)
- improve corruption detection for AGFL entries, AGFL indexes and
XEFI extents (syzkaller fuzzer oops report)
- Avoid double perag reference release (regression fix)
- Improve extent merging detection in scrub (regression fix)
- Fix a new undefined high bit shift (regression fix)
- Fix for AGF vs inode cluster buffer deadlock (regression fix)"
* tag 'xfs-6.4-rc5-fixes' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: collect errors from inodegc for unlinked inode recovery
xfs: validate block number being freed before adding to xefi
xfs: validity check agbnos on the AGFL
xfs: fix agf/agfl verification on v4 filesystems
xfs: fix double xfs_perag_rele() in xfs_filestream_pick_ag()
xfs: fix broken logic when detecting mergeable bmap records
xfs: Fix undefined behavior of shift into sign bit
xfs: fix AGF vs inode cluster buffer deadlock
xfs: defered work could create precommits
xfs: restore allocation trylock iteration
xfs: buffer pins need to hold a buffer reference
|
|
ext4_xattr_block_set() relies on its caller to call dquot_initialize()
on the inode. To assure that this has happened there are WARN_ON
checks. Unfortunately, this is subject to false positives if there is
an antagonist thread which is flipping the file system at high rates
between r/o and rw. So only do the check if EXT4_XATTR_DEBUG is
enabled.
Link: https://lore.kernel.org/r/20230608044056.GA1418535@mit.edu
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
re-enabled"
This reverts commit a44be64bbecb15a452496f60db6eacfee2b59c79.
Link: https://lore.kernel.org/r/653b3359-2005-21b1-039d-c55ca4cffdcc@gmail.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
[BUG]
After the recent scrub rework introduced in commit e02ee89baa66 ("btrfs:
scrub: switch scrub_simple_mirror() to scrub_stripe infrastructure"),
btrfs scrub no longer reports repaired errors any more:
# mkfs.btrfs -f $dev -d DUP
# mount $dev $mnt
# xfs_io -f -d -c "pwrite -b 64K -S 0xaa 0 64" $mnt/file
# umount $dev
# xfs_io -f -c "pwrite -S 0xff $phy1 64K" $dev # Corrupt the first mirror
# mount $dev $mnt
# btrfs scrub start -BR $mnt
scrub done for 725e7cb7-8a4a-4c77-9f2a-86943619e218
Scrub started: Tue Jun 6 14:56:50 2023
Status: finished
Duration: 0:00:00
data_extents_scrubbed: 2
tree_extents_scrubbed: 18
data_bytes_scrubbed: 131072
tree_bytes_scrubbed: 294912
read_errors: 0
csum_errors: 0 <<< No errors here
verify_errors: 0
[...]
uncorrectable_errors: 0
unverified_errors: 0
corrected_errors: 16 <<< Only corrected errors
last_physical: 2723151872
This can confuse btrfs-progs, as it relies on the csum_errors to
determine if there is anything wrong.
While on v6.3.x kernels, the report is different:
csum_errors: 16 <<<
verify_errors: 0
[...]
uncorrectable_errors: 0
unverified_errors: 0
corrected_errors: 16 <<<
[CAUSE]
In the reworked scrub, we update the scrub progress inside
scrub_stripe_report_errors(), using various bitmaps to update the
result.
For example for csum_errors, we use bitmap_weight() of
stripe->csum_error_bitmap.
Unfortunately at that stage, all error bitmaps (except
init_error_bitmap) are the result of the latest repair attempt, thus if
the stripe is fully repaired, those error bitmaps will all be empty,
resulting the above output mismatch.
To fix this, record the number of errors into stripe->init_nr_*_errors.
Since we don't really care about where those errors are, we only need to
record the number of errors.
Then in scrub_stripe_report_errors(), use those initial numbers to
update the progress other than using the latest error bitmaps.
Fixes: e02ee89baa66 ("btrfs: scrub: switch scrub_simple_mirror() to scrub_stripe infrastructure")
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
[BUG]
With recent scrub rework, the scrub operation no longer respects the
read-only flag passed by "-r" option of "btrfs scrub start" command.
# mkfs.btrfs -f -d raid1 $dev1 $dev2
# mount $dev1 $mnt
# xfs_io -f -d -c "pwrite -b 128K -S 0xaa 0 128k" $mnt/file
# sync
# xfs_io -c "pwrite -S 0xff $phy1 64k" $dev1
# xfs_io -c "pwrite -S 0xff $((phy2 + 65536)) 64k" $dev2
# mount $dev1 $mnt -o ro
# btrfs scrub start -BrRd $mnt
Scrub device $dev1 (id 1) done
Scrub started: Tue Jun 6 09:59:14 2023
Status: finished
Duration: 0:00:00
[...]
corrected_errors: 16 <<< Still has corrupted sectors
last_physical: 1372585984
Scrub device $dev2 (id 2) done
Scrub started: Tue Jun 6 09:59:14 2023
Status: finished
Duration: 0:00:00
[...]
corrected_errors: 16 <<< Still has corrupted sectors
last_physical: 1351614464
# btrfs scrub start -BrRd $mnt
Scrub device $dev1 (id 1) done
Scrub started: Tue Jun 6 10:00:17 2023
Status: finished
Duration: 0:00:00
[...]
corrected_errors: 0 <<< No more errors
last_physical: 1372585984
Scrub device $dev2 (id 2) done
[...]
corrected_errors: 0 <<< No more errors
last_physical: 1372585984
[CAUSE]
In the newly reworked scrub code, repair is always submitted no matter
if we're doing a read-only scrub.
[FIX]
Fix it by skipping the write submission if the scrub is a read-only one.
Unfortunately for the report part, even for a read-only scrub we will
still report it as corrected errors, as we know it's repairable, even we
won't really submit the write.
Fixes: e02ee89baa66 ("btrfs: scrub: switch scrub_simple_mirror() to scrub_stripe infrastructure")
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
There is a race between capsnaps flush and removing the inode from
'mdsc->snap_flush_list' list:
== Thread A == == Thread B ==
ceph_queue_cap_snap()
-> allocate 'capsnapA'
->ihold('&ci->vfs_inode')
->add 'capsnapA' to 'ci->i_cap_snaps'
->add 'ci' to 'mdsc->snap_flush_list'
...
== Thread C ==
ceph_flush_snaps()
->__ceph_flush_snaps()
->__send_flush_snap()
handle_cap_flushsnap_ack()
->iput('&ci->vfs_inode')
this also will release 'ci'
...
== Thread D ==
ceph_handle_snap()
->flush_snaps()
->iterate 'mdsc->snap_flush_list'
->get the stale 'ci'
->remove 'ci' from ->ihold(&ci->vfs_inode) this
'mdsc->snap_flush_list' will WARNING
To fix this we will increase the inode's i_count ref when adding 'ci'
to the 'mdsc->snap_flush_list' list.
[ idryomov: need_put int -> bool ]
Cc: stable@vger.kernel.org
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2209299
Signed-off-by: Xiubo Li <xiubli@redhat.com>
Reviewed-by: Milind Changire <mchangir@redhat.com>
Reviewed-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
kafs incorrectly passes a zero mtime (ie. 1st Jan 1970) to the server when
creating a file, dir or symlink because the mtime recorded in the
afs_operation struct gets passed to the server by the marshalling routines,
but the afs_mkdir(), afs_create() and afs_symlink() functions don't set it.
This gets masked if a file or directory is subsequently modified.
Fix this by filling in op->mtime before calling the create op.
Fixes: e49c7b2f6de7 ("afs: Build an abstraction around an "operation" concept")
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Jeffrey Altman <jaltman@auristor.com>
Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
cc: linux-fsdevel@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The async discard uses the BTRFS_FS_DISCARD_RUNNING bit in the fs_info
to force discards off when the filesystem has aborted or we're generally
not able to run discards. This gets flipped on when we're mounted rw,
and also when we go from ro->rw.
Commit 63a7cb13071842 ("btrfs: auto enable discard=async when possible")
enabled async discard by default, and this meant
"mount -o ro /dev/xxx /yyy" had async discards turned on.
Unfortunately, this meant our check in btrfs_remount_cleanup() would see
that discards are already on:
/* If we toggled discard async */
if (!btrfs_raw_test_opt(old_opts, DISCARD_ASYNC) &&
btrfs_test_opt(fs_info, DISCARD_ASYNC))
btrfs_discard_resume(fs_info);
So, we'd never call btrfs_discard_resume() when remounting the root
filesystem from ro->rw.
drgn shows this really nicely:
import os
import sys
from drgn.helpers.linux.fs import path_lookup
from drgn import NULL, Object, Type, cast
def btrfs_sb(sb):
return cast("struct btrfs_fs_info *", sb.s_fs_info)
if len(sys.argv) == 1:
path = "/"
else:
path = sys.argv[1]
fs_info = cast("struct btrfs_fs_info *", path_lookup(prog, path).mnt.mnt_sb.s_fs_info)
BTRFS_FS_DISCARD_RUNNING = 1 << prog['BTRFS_FS_DISCARD_RUNNING']
if fs_info.flags & BTRFS_FS_DISCARD_RUNNING:
print("discard running flag is on")
else:
print("discard running flag is off")
[root]# mount | grep nvme
/dev/nvme0n1p3 on / type btrfs
(rw,relatime,compress-force=zstd:3,ssd,discard=async,space_cache=v2,subvolid=5,subvol=/)
[root]# ./discard_running.drgn
discard running flag is off
[root]# mount -o remount,discard=sync /
[root]# mount -o remount,discard=async /
[root]# ./discard_running.drgn
discard running flag is on
The fix is to call btrfs_discard_resume() when we're going from ro->rw.
It already checks to make sure the async discard flag is on, so it'll do
the right thing.
Fixes: 63a7cb13071842 ("btrfs: auto enable discard=async when possible")
CC: stable@vger.kernel.org # 6.3+
Reviewed-by: Boris Burkov <boris@bur.io>
Signed-off-by: Chris Mason <clm@fb.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2
Pull gfs2 fix from Andreas Gruenbacher:
- Don't get stuck writing page onto itself under direct I/O
* tag 'gfs2-v6.4-rc4-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2:
gfs2: Don't get stuck writing page onto itself under direct I/O
|