| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Use the bitmap operations when accessing the advertised/supported link
modes and remove places that access them as arrays of unsigned longs
(underlying implementation of the bitmap), this makes the code much more
readable and clear.
Signed-off-by: Gal Pressman <[email protected]>
Reviewed-by: Carolina Jubran <[email protected]>
Signed-off-by: Tariq Toukan <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Firmware has the limitation that it cannot offload a rule with rewrite
and mirror to internal and external destinations simultaneously.
This patch adds a workaround to this issue. Here the destination array
is split again, just like what's done in previous commit, but after
the action indexed by split_count - 1. An extra rule is added for the
leftover destinations. Such rule can be offloaded, even there are
destinations to both internal and external destinations, because the
header rewrite is left in the original FTE.
Signed-off-by: Jianbo Liu <[email protected]>
Reviewed-by: Cosmin Ratiu <[email protected]>
Signed-off-by: Tariq Toukan <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
To offload the encap rule when the tunnel IP is configured on an
openvswitch internal port, driver need to overwrite vport metadata in
reg_c0 to the value assigned to the internal port, then forward
packets to root table to be processed again by the rules matching on
the metadata for such internal port.
When such rule is combined with header rewrite and mirror, openvswitch
generates the rule like the following, because it resets mirror after
packets are modified.
in_port(enp8s0f0npf0sf1),..,
actions:enp8s0f0npf0sf2,set(tunnel(...)),set(ipv4(...)),vxlan_sys_4789,enp8s0f0npf0sf2
The split_count was introduced before to support rewrite and mirror.
Driver splits the rule into two different hardware rules in order to
offload it. But it's not enough to offload the above complicated rule
because of the limitations, in both driver and firmware.
To resolve this issue, the destination array is split again after the
destination indexed by split_count. An extra rule is added for the
leftover destinations (in the above example, it is enp8s0f0npf0sf2),
and is inserted to post_act table. And the extra destination is added
in the original rule to forward to post_act table, so the extra mirror
is done there.
Signed-off-by: Jianbo Liu <[email protected]>
Reviewed-by: Cosmin Ratiu <[email protected]>
Signed-off-by: Tariq Toukan <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
In the commit a2a73ea14b1a ("net/mlx5e: Don't listen to remove flows
event"), remove_flow_enable event is removed, and the hard limit
usually relies on software mechanism added in commit b2f7b01d36a9
("net/mlx5e: Simulate missing IPsec TX limits hardware
functionality"). But the delayed work is rescheduled every one second,
which is slow for fast traffic. As a result, traffic can't be blocked
even reaches the hard limit, which usually happens when soft and hard
limits are very close.
In reality it won't happen because soft limit is much lower than hard
limit. But, as an optimization for RX to block traffic when reaching
hard limit, need to set remove_flow_enable. When remove flow is
enabled, IPSEC HARD_LIFETIME ASO syndrome will be set in the metadata
defined in the ASO return register if packets reach hard lifetime
threshold. And those packets are dropped immediately by the steering
table.
Signed-off-by: Jianbo Liu <[email protected]>
Reviewed-by: Leon Romanovsky <[email protected]>
Signed-off-by: Tariq Toukan <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Currently MLX5E_TC_MAX_INT_PORT_NUM is 8. Usually int port has one
ingress and one egress rules. But sometimes, a temporary rule can be
offloaded as well, eg:
recirc_id(0),in_port(br-phy),eth(src=10:70:fd:87:57:c0,dst=33:33:00:00:00:16),
eth_type(0x86dd),ipv6(frag=no), packets:2, bytes:180, used:0.060s,
actions:enp8s0f0
If one int port device offloads 3 rules, only 2 devices can offload.
Other devices will hit the limit and fail to offload. Actually it is
insufficient for customers. So increase the number to 32.
Signed-off-by: Chris Mi <[email protected]>
Reviewed-by: Roi Dayan <[email protected]>
Signed-off-by: Tariq Toukan <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
f1294617d2f38bd2b9f6cce516b0326858b61182 removed the custom function for
ndo_eth_ioctl and used the standard phy_do_ioctl which calls
phy_mii_ioctl. However since then, this driver was ported to phylink
where it makes more sense to call phylink_mii_ioctl.
Bring back custom function that calls phylink_mii_ioctl.
Signed-off-by: Rosen Penev <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
During initialization with the vnic server, a bitstring is communicated
to the client regarding header info needed during CSO (See "VNIC
Capabilities" in PAPR). Most of the time, to be safe, vnic server
requests header info for CSO. When header info is needed, multiple TX
descriptors are required per skb; This limits the driver to use
send_subcrq_indirect instead of send_subcrq_direct.
Previously, the vnic server request for header info was ignored. This
allowed the use of send_sub_crq_direct. Transmissions were successful
because the bitstring returned by vnic server is broad and over
cautionary. It was observed that mlx backing devices could actually
transmit and handle CSO packets without the vnic server receiving
header info (despite the fact that the bitstring requested it).
There was a trust issue: The bitstring was overcautionary. This extra
precaution (requesting header info when the backing device may not use
it) comes at the cost of performance (using direct vs indirect hcalls
has a 30% delta in small packet RR transaction rate). So it has been
requested that the vnic server team tries to ensure that the bitstring
is more exact. In the meantime, disable CSO when it is possible to use
the skb in the send_subcrq_direct path. In other words, calculate the
checksum before handing the packet to FW when the packet is not
segmented and xmit_more is false.
Since the code path is only possible if the skb is non GSO and xmit_more
is false, the cost of doing checksum in the send_subcrq_direct path is
minimal. Any large segmented skb will have xmit_more set to true more
frequently and it is inexpensive to do checksumming on a small skb.
The worst-case workload would be a 9000 MTU TCP_RR test with close
to MTU sized packets (and TSO off). This allows xmit_more to be false
more frequently and open the code path up to use send_subcrq_direct.
Observing trace data (graph-time = 1) and packet rate with this workload
shows minimal performance degradation:
1. NIC does checksum w headers, safely use send_subcrq_indirect:
- Packet rate: 631k txs
- Trace data:
ibmvnic_xmit = 44344685.87 us / 6234576 hits = AVG 7.11 us
skb_checksum_help = 4.07 us / 2 hits = AVG 2.04 us
^ Notice hits, tracing this just for reassurance
ibmvnic_tx_scrq_flush = 33040649.69 us / 5638441 hits = AVG 5.86 us
send_subcrq_indirect = 37438922.24 us / 6030859 hits = AVG 6.21 us
2. NIC does checksum w/o headers, dangerously use send_subcrq_direct:
- Packet rate: 831k txs
- Trace data:
ibmvnic_xmit = 48940092.29 us / 8187630 hits = AVG 5.98 us
skb_checksum_help = 2.03 us / 1 hits = AVG 2.03
ibmvnic_tx_scrq_flush = 31141879.57 us / 7948960 hits = AVG 3.92 us
send_subcrq_indirect = 8412506.03 us / 728781 hits = AVG 11.54
^ notice hits is much lower b/c send_subcrq_direct was called
^ wasn't traceable
3. driver does checksum, safely use send_subcrq_direct (THIS PATCH):
- Packet rate: 829k txs
- Trace data:
ibmvnic_xmit = 56696077.63 us / 8066168 hits = AVG 7.03 us
skb_checksum_help = 8587456.16 us / 7526072 hits = AVG 1.14 us
ibmvnic_tx_scrq_flush = 30219545.55 us / 7782409 hits = AVG 3.88 us
send_subcrq_indirect = 8638326.44 us / 763693 hits = AVG 11.31 us
When the bitstring ever specifies that CSO does not require headers
(dependent on VIOS vnic server changes), then this patch should be
removed and replaced with one that investigates the bitstring before
using send_subcrq_direct.
Signed-off-by: Nick Child <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Byte Queue Limits depends on dql_completed being called once per tx
completion round in order to adjust its algorithm appropriately. The
dql->limit value is an approximation of the amount of bytes that the NIC
can consume per irq interval. If this approximation is too high then the
NIC will become over-saturated. Too low and the NIC will starve.
The dql->limit depends on dql->prev-* stats to calculate an optimal
value. If dql_completed() is called more than once per irq handler then
those prev-* values become unreliable (because they are not an accurate
representation of the previous state of the NIC) resulting in a
sub-optimal limit value.
Therefore, move the call to netdev_tx_completed_queue() to the end of
ibmvnic_complete_tx().
When performing 150 sessions of TCP rr (request-response 1 byte packets)
workloads, one could observe:
PREVIOUSLY: - limit and inflight values hovering around 130
- transaction rate of around 750k pps.
NOW: - limit rises and falls in response to inflight (130-900)
- transaction rate of around 1M pps (33% improvement)
Signed-off-by: Nick Child <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Firmware supports two hcalls to send a sub-crq request:
H_SEND_SUB_CRQ_INDIRECT and H_SEND_SUB_CRQ. The indirect hcall allows
for submission of batched messages while the other hcall is limited to
only one message. This protocol is defined in PAPR section 17.2.3.3.
Previously, the ibmvnic xmit function only used the indirect hcall. This
allowed the driver to batch it's skbs. A single skb can occupy a few
entries per hcall depending on if FW requires skb header information or
not. The FW only needs header information if the packet is segmented.
By this logic, if an skb is not GSO then it can fit in one sub-crq
message and therefore is a candidate for H_SEND_SUB_CRQ.
Batching skb transmission is only useful when there are more packets
coming down the line (ie netdev_xmit_more is true).
As it turns out, H_SEND_SUB_CRQ induces less latency than
H_SEND_SUB_CRQ_INDIRECT. Therefore, use H_SEND_SUB_CRQ where
appropriate.
Small latency gains seen when doing TCP_RR_150 (request/response
workload). Ftrace results (graph-time=1):
Previous:
ibmvnic_xmit = 29618270.83 us / 8860058.0 hits = AVG 3.34
ibmvnic_tx_scrq_flush = 21972231.02 us / 6553972.0 hits = AVG 3.35
Now:
ibmvnic_xmit = 22153350.96 us / 8438942.0 hits = AVG 2.63
ibmvnic_tx_scrq_flush = 15858922.4 us / 6244076.0 hits = AVG 2.54
Signed-off-by: Nick Child <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
send_subcrq_[in]direct() already has a dma memory barrier.
Remove the earlier one.
Signed-off-by: Nick Child <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Previously when creating the header descriptors, the driver would:
1. allocate a temporary buffer on the stack (in build_hdr_descs_arr)
2. memcpy the header info into the temporary buffer (in build_hdr_data)
3. memcpy the temp buffer into a local variable (in create_hdr_descs)
4. copy the local variable into the return buffer (in create_hdr_descs)
Since, there is no opportunity for errors during this process, the temp
buffer is not needed and work can be done on the return buffer directly.
Repurpose build_hdr_data() to only calculate the header lengths. Rename
it to get_hdr_lens().
Edit create_hdr_descs() to read from the skb directly and copy directly
into the returned useful buffer.
The process now involves less memory and write operations while
also being more readable.
Signed-off-by: Nick Child <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Use the header length helper functions rather than trying to calculate
it within the driver. There are defined functions for mac and network
headers (skb_mac_header_len and skb_network_header_len) but no such
function exists for the transport header length.
Also, hdr_data was memset during allocation to all 0's so no need to
memset again.
Signed-off-by: Nick Child <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Previously, the driver would replenish the rx pool if the polling
function consumed less than the budget. The logic being that the driver
did not exhaust its budget so that must mean that the driver is not busy
and has cycles to spare for replenishing the pool.
So pool replenishment happens on every poll which did not consume
the budget. This can very costly during request-response tests.
In fact, an extra ~100pps can be seen in TCP_RR_150 tests when we remove
this conditional. Trace results (ftrace, graph-time=1) for the poll
function are below:
Previous results:
ibmvnic_poll = 64951846.0 us / 4167628.0 hits = AVG 15.58
replenish_rx_pool = 17602846.0 us / 4710437.0 hits = AVG 3.74
Now:
ibmvnic_poll = 57673941.0 us / 4791737.0 hits = AVG 12.04
replenish_rx_pool = 3938171.6 us / 4314.0 hits = AVG 912.88
While the replenish function takes longer, it is hit less frequently
meaning the ibmvnic_poll function, on average, is faster.
Furthermore, this change does not have a negative effect on
performance bandwidth/latency measurements.
Signed-off-by: Nick Child <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Building fs_enet on powerpc e500 leads to following warning:
CC drivers/net/ethernet/freescale/fs_enet/mac-scc.o
In file included from ./include/linux/build_bug.h:5,
from ./include/linux/container_of.h:5,
from ./include/linux/list.h:5,
from ./include/linux/module.h:12,
from drivers/net/ethernet/freescale/fs_enet/mac-scc.c:15:
drivers/net/ethernet/freescale/fs_enet/mac-scc.c: In function 'allocate_bd':
./include/linux/err.h:28:49: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
28 | #define IS_ERR_VALUE(x) unlikely((unsigned long)(void *)(x) >= (unsigned long)-MAX_ERRNO)
| ^
./include/linux/compiler.h:77:45: note: in definition of macro 'unlikely'
77 | # define unlikely(x) __builtin_expect(!!(x), 0)
| ^
drivers/net/ethernet/freescale/fs_enet/mac-scc.c:138:13: note: in expansion of macro 'IS_ERR_VALUE'
138 | if (IS_ERR_VALUE(fep->ring_mem_addr))
| ^~~~~~~~~~~~
This is due to fep->ring_mem_addr not being a pointer but a DMA
address which is 64 bits on that platform while pointers are
32 bits as this is a 32 bits platform with wider physical bus.
However, using fep->ring_mem_addr is just wrong because
cpm_muram_alloc() returns an offset within the muram and not
a physical address directly. So use fpi->dpram_offset instead.
Signed-off-by: Christophe Leroy <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Link: https://patch.msgid.link/ec67ea3a3bef7e58b8dc959f7c17d405af0d27e4.1723101144.git.christophe.leroy@csgroup.eu
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
The usbnet_link_change function is not called, if the link has not changed.
...
[16913.807393][ 3] cdc_ether 1-2:2.0 enx00e0995fd1ac: kevent 12 may have been dropped
[16913.822266][ 2] cdc_ether 1-2:2.0 enx00e0995fd1ac: kevent 12 may have been dropped
[16913.826296][ 2] cdc_ether 1-2:2.0 enx00e0995fd1ac: kevent 11 may have been dropped
...
kevent 11 is scheduled too frequently and may affect other event schedules.
Signed-off-by: zhangxiangqian <[email protected]>
Acked-by: Oliver Neukum <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
syzbot/KMSAN reported use of uninit-value in get_dev_xmit() [1]
We must make sure the IPv4 or Ipv6 header is pulled in skb->head
before accessing fields in them.
Use pskb_inet_may_pull() to fix this issue.
[1]
BUG: KMSAN: uninit-value in ipv6_pdp_find drivers/net/gtp.c:220 [inline]
BUG: KMSAN: uninit-value in gtp_build_skb_ip6 drivers/net/gtp.c:1229 [inline]
BUG: KMSAN: uninit-value in gtp_dev_xmit+0x1424/0x2540 drivers/net/gtp.c:1281
ipv6_pdp_find drivers/net/gtp.c:220 [inline]
gtp_build_skb_ip6 drivers/net/gtp.c:1229 [inline]
gtp_dev_xmit+0x1424/0x2540 drivers/net/gtp.c:1281
__netdev_start_xmit include/linux/netdevice.h:4913 [inline]
netdev_start_xmit include/linux/netdevice.h:4922 [inline]
xmit_one net/core/dev.c:3580 [inline]
dev_hard_start_xmit+0x247/0xa20 net/core/dev.c:3596
__dev_queue_xmit+0x358c/0x5610 net/core/dev.c:4423
dev_queue_xmit include/linux/netdevice.h:3105 [inline]
packet_xmit+0x9c/0x6c0 net/packet/af_packet.c:276
packet_snd net/packet/af_packet.c:3145 [inline]
packet_sendmsg+0x90e3/0xa3a0 net/packet/af_packet.c:3177
sock_sendmsg_nosec net/socket.c:730 [inline]
__sock_sendmsg+0x30f/0x380 net/socket.c:745
__sys_sendto+0x685/0x830 net/socket.c:2204
__do_sys_sendto net/socket.c:2216 [inline]
__se_sys_sendto net/socket.c:2212 [inline]
__x64_sys_sendto+0x125/0x1d0 net/socket.c:2212
x64_sys_call+0x3799/0x3c10 arch/x86/include/generated/asm/syscalls_64.h:45
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xcd/0x1e0 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Uninit was created at:
slab_post_alloc_hook mm/slub.c:3994 [inline]
slab_alloc_node mm/slub.c:4037 [inline]
kmem_cache_alloc_node_noprof+0x6bf/0xb80 mm/slub.c:4080
kmalloc_reserve+0x13d/0x4a0 net/core/skbuff.c:583
__alloc_skb+0x363/0x7b0 net/core/skbuff.c:674
alloc_skb include/linux/skbuff.h:1320 [inline]
alloc_skb_with_frags+0xc8/0xbf0 net/core/skbuff.c:6526
sock_alloc_send_pskb+0xa81/0xbf0 net/core/sock.c:2815
packet_alloc_skb net/packet/af_packet.c:2994 [inline]
packet_snd net/packet/af_packet.c:3088 [inline]
packet_sendmsg+0x749c/0xa3a0 net/packet/af_packet.c:3177
sock_sendmsg_nosec net/socket.c:730 [inline]
__sock_sendmsg+0x30f/0x380 net/socket.c:745
__sys_sendto+0x685/0x830 net/socket.c:2204
__do_sys_sendto net/socket.c:2216 [inline]
__se_sys_sendto net/socket.c:2212 [inline]
__x64_sys_sendto+0x125/0x1d0 net/socket.c:2212
x64_sys_call+0x3799/0x3c10 arch/x86/include/generated/asm/syscalls_64.h:45
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xcd/0x1e0 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x77/0x7f
CPU: 0 UID: 0 PID: 7115 Comm: syz.1.515 Not tainted 6.11.0-rc1-syzkaller-00043-g94ede2a3e913 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 06/27/2024
Fixes: 999cb275c807 ("gtp: add IPv6 support")
Fixes: 459aa660eb1d ("gtp: add initial driver for datapath of GPRS Tunneling Protocol (GTP-U)")
Signed-off-by: Eric Dumazet <[email protected]>
Cc: Harald Welte <[email protected]>
Reviewed-by: Pablo Neira Ayuso <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A few SPI fixes: clock rate calculation fixes for the Kunpeng and lpsi
drivers and a missing registration of a device ID for spidev (which
had only been updated for DT cases, causing warnings)"
* tag 'spi-fix-v6.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: spi-fsl-lpspi: Fix scldiv calculation
spi: spidev: Add missing spi_device_id for bh2228fv
spi: hisi-kunpeng: Add verification for the max_frequency provided by the firmware
spi: hisi-kunpeng: Add validation for the minimum value of speed_hz
|
|
Add the missing clk_disable_unprepare() before return in
cctrng_resume().
Fixes: a583ed310bb6 ("hwrng: cctrng - introduce Arm CryptoCell driver")
Cc: <[email protected]>
Signed-off-by: Gaosheng Cui <[email protected]>
Signed-off-by: Herbert Xu <[email protected]>
|
|
Add the missing clk_disable_unprepare() before return in
bcm2835_rng_init().
Fixes: e5f9f41d5e62 ("hwrng: bcm2835 - add reset support")
Cc: <[email protected]>
Signed-off-by: Gaosheng Cui <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: Herbert Xu <[email protected]>
|
|
Rockchip SoCs used to have a random number generator as part of their
crypto device, and support for it has to be added to the corresponding
driver. However newer Rockchip SoCs like the RK3568 have an independent
True Random Number Generator device. This patch adds a driver for it,
greatly inspired from the downstream driver.
The TRNG device does not seem to have a signal conditionner and the FIPS
140-2 test returns a lot of failures. They can be reduced by increasing
RK_RNG_SAMPLE_CNT, in a tradeoff between quality and speed. This value
has been adjusted to get ~90% of successes and the quality value has
been set accordingly.
Signed-off-by: Aurelien Jarno <[email protected]>
[[email protected]: code style fixes]
Signed-off-by: Daniel Golle <[email protected]>
Acked-by: Krzysztof Kozlowski <[email protected]>
Signed-off-by: Herbert Xu <[email protected]>
|
|
Switch cpumask_t to cpumask_var_t as the former may be too big
for the stack:
CC [M] drivers/crypto/caam/qi.o
CC [M] drivers/crypto/caam/caamalg_qi2.o
../drivers/crypto/caam/qi.c: In function ‘caam_qi_init’:
../drivers/crypto/caam/qi.c:808:1: warning: the frame size of 1056 bytes is larger than 1024 bytes [-Wframe-larger-than=]
808 | }
| ^
CHECK ../drivers/crypto/caam/qi.c
../drivers/crypto/caam/caamalg_qi2.c: In function ‘dpaa2_dpseci_setup’:
../drivers/crypto/caam/caamalg_qi2.c:5135:1: warning: the frame size of 1032 bytes is larger than 1024 bytes [-Wframe-larger-than=]
5135 | }
| ^
Also fix the error path handling in qi.c.
Signed-off-by: Herbert Xu <[email protected]>
|
|
Before commit addea5858b66 ("hwrng: Kconfig - Do not enable by default
CN10K driver") the Marvell CN10K Random Number Generator was always
enabled when HW_RANDOM was enabled.
This was changed with that commit to prevent having this driver being
always enabled on arm64. To prevent introducing regression with some old
defconfig enable the driver when ARCH_THUNDER is enabled.
Fixes: addea5858b66 ("hwrng: Kconfig - Do not enable by default CN10K driver")
Closes: https://lore.kernel.org/all/SN7PR18MB53144B37B82ADEEC5D35AE0CE3AC2@SN7PR18MB5314.namprd18.prod.outlook.com/
Signed-off-by: Francesco Dolcini <[email protected]>
Signed-off-by: Herbert Xu <[email protected]>
|
|
Signed-off-by: Bhoomika K <[email protected]>
Signed-off-by: Pavitrakumar M <[email protected]>
Acked-by: Ruud Derwig <[email protected]>
Signed-off-by: Herbert Xu <[email protected]>
|
|
Signed-off-by: shwetar <[email protected]>
Signed-off-by: Pavitrakumar M <[email protected]>
Acked-by: Ruud Derwig <[email protected]>
Signed-off-by: Herbert Xu <[email protected]>
|
|
Signed-off-by: shwetar <[email protected]>
Signed-off-by: Pavitrakumar M <[email protected]>
Acked-by: Ruud Derwig <[email protected]>
Signed-off-by: Herbert Xu <[email protected]>
|
|
Signed-off-by: shwetar <[email protected]>
Signed-off-by: Pavitrakumar M <[email protected]>
Acked-by: Ruud Derwig <[email protected]>
Signed-off-by: Herbert Xu <[email protected]>
|
|
Signed-off-by: Bhoomika K <[email protected]>
Signed-off-by: Pavitrakumar M <[email protected]>
Acked-by: Ruud Derwig <[email protected]>
Signed-off-by: Herbert Xu <[email protected]>
|
|
Signed-off-by: Bhoomika K <[email protected]>
Signed-off-by: Pavitrakumar M <[email protected]>
Acked-by: Ruud Derwig <[email protected]>
Signed-off-by: Herbert Xu <[email protected]>
|
|
Use a dummy xe_debugfs_register() if debugfs is not enabled and move all
debugfs-related files under `ifeq ($(CONFIG_DEBUG_FS),y)` in the
Makefile. This is similar to what was done for display in
commit 439987f6f471 ("drm/xe: don't build debugfs files when
CONFIG_DEBUG_FS=n").
This removes the following warning while loading xe with
CONFIG_DEUBG_FS=n:
xe 0000:03:00.0: [drm] Create GT directory failed
Reviewed-by: Nirmoy Das <[email protected]>
Reviewed-by: Matthew Brost <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
Signed-off-by: Lucas De Marchi <[email protected]>
|
|
Switching modes between LR and dma-fence can result in multiple calls to
suspend / resume. Make these calls safe while still enforcing call
order.
Signed-off-by: Matthew Brost <[email protected]>
Reviewed-by: Jonathan Cavitt <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
No need to enable scheduling in already enabled.
Signed-off-by: Matthew Brost <[email protected]>
Reviewed-by: Jonathan Cavitt <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Will help by allowing callers to own message locking.
Signed-off-by: Matthew Brost <[email protected]>
Reviewed-by: Jonathan Cavitt <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Will help to avoid adding a static message twice.
Signed-off-by: Matthew Brost <[email protected]>
Reviewed-by: Jonathan Cavitt <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Will help callers to own locking when adding messages to scheduler.
Signed-off-by: Matthew Brost <[email protected]>
Reviewed-by: Jonathan Cavitt <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
cxl_setup_parent_dport() needs to get RCH dport AER capability address
from RCRB to disable AER interrupt. The function does not check if dport
is RCH dport, it will get a wrong pci_host_bridge structure by dport_dev
in VH case because dport_dev points to a pci device(RP or switch DSP)
rather than a pci host bridge device.
Fixes: f05fd10d138d ("cxl/pci: Add RCH downstream port AER register discovery")
Signed-off-by: Li Ming <[email protected]>
Reviewed-by: Dan Williams <[email protected]>
Reviewed-by: Ira Weiny <[email protected]>
Tested-by: Ira Weiny <[email protected]>
Tested-by: Alison Schofield <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Dave Jiang <[email protected]>
|
|
Pull drm fixes from Dave Airlie:
"Weekly regular fixes, mostly amdgpu with i915/xe having a few each,
and then some misc bits across the board, seems about right for rc3
time.
client:
- fix null ptr deref
bridge:
- connector: fix double free
atomic:
- fix async flip update
panel:
- document panel
omap:
- add config dependency
tests:
- fix gem shmem test
drm buddy:
- Add start address to trim function
amdgpu:
- DMCUB fix
- Fix DET programming on some DCNs
- DCC fixes
- DCN 4.0.1 fixes
- SMU 14.0.x update
- MMHUB fix
- DCN 3.1.4 fix
- GC 12.0 fixes
- Fix soft recovery error propogation
- SDMA 7.0 fixes
- DSC fix
xe:
- Fix off-by-one when processing RTP rules
- Use dma_fence_chain_free in chain fence unused as a sync
- Fix PL1 disable flow in xe_hwmon_power_max_write
- Take ref to VM in delayed dump snapshot
i915:
- correct dual pps handling for MTL_PCH+ [display]
- Adjust vma offset for framebuffer mmap offset [gem]
- Fix Virtual Memory mapping boundaries calculation [gem]
- Allow evicting to use the requested placement
- Attempt to get pages without eviction first"
* tag 'drm-fixes-2024-08-10' of https://gitlab.freedesktop.org/drm/kernel: (31 commits)
drm/xe: Take ref to VM in delayed snapshot
drm/xe/hwmon: Fix PL1 disable flow in xe_hwmon_power_max_write
drm/xe: Use dma_fence_chain_free in chain fence unused as a sync
drm/xe/rtp: Fix off-by-one when processing rules
drm/amdgpu: Add DCC GFX12 flag to enable address alignment
drm/amdgpu: correct sdma7 max dw
drm/amdgpu: Add address alignment support to DCC buffers
drm/amd/display: Skip Recompute DSC Params if no Stream on Link
drm/amdgpu: change non-dcc buffer copy configuration
drm/amdgpu: Forward soft recovery errors to userspace
drm/amdgpu: add golden setting for gc v12
drm/buddy: Add start address support to trim function
drm/amd/display: Add missing program DET segment call to pipe init
drm/amd/display: Add missing DCN314 to the DML Makefile
drm/amdgpu: force to use legacy inv in mmhub
drm/amd/pm: update powerplay structure on smu v14.0.2/3
drm/amd/display: Add missing mcache registers
drm/amd/display: Add dcc propagation value
drm/amd/display: Add missing DET segments programming
drm/amd/display: Replace dm_execute_dmub_cmd with dc_wake_and_execute_dmub_cmd
...
|
|
__pci_reset_bus() calls pci_bridge_secondary_bus_reset() to perform the
reset and also waits for the Secondary Bus to become again accessible.
__pci_reset_bus() then calls pci_bus_restore_locked() that restores the PCI
devices connected to the bus, and if necessary, recursively restores also
the subordinate buses and their devices.
The logic in pci_bus_restore_locked() does not take into account that after
restoring a device on one level, there might be another Link Downstream
that can only start to come up after restore has been performed for its
Downstream Port device. That is, the Link may require additional wait until
it becomes accessible.
Similarly, pci_slot_restore_locked() lacks wait.
Amend pci_bus_restore_locked() and pci_slot_restore_locked() to wait for
the Secondary Bus before recursively performing the restore of that bus.
Fixes: 090a3c5322e9 ("PCI: Add pci_reset_slot() and pci_reset_bus()")
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Ilpo Järvinen <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
|
|
The critical section which requires the VM dma-resv is the call
xe_lrc_create in __xe_exec_queue_init. Move this lock to
__xe_exec_queue_init holding it just around xe_lrc_create. Not only is
good practice, this also fixes a locking double of the VM dma-resv in
the error paths of __xe_exec_queue_init as xe_lrc_put tries to acquire
this too resulting in a deadlock.
Fixes: dd08ebf6c352 ("drm/xe: Introduce a new DRM driver for Intel GPUs")
Cc: Maarten Lankhorst <[email protected]>
Signed-off-by: Matthew Brost <[email protected]>
Reviewed-by: Maarten Lankhorst <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
ast currently ioremaps two PCI BARs using pcim_iomap(). It does not perform
a request on the regions, however, which would make the driver a bit more
robust.
PCI now offers pcim_iomap_region(), a managed function which both requests
and ioremaps a BAR.
Replace pcim_iomap() with pcim_iomap_region().
Suggested-by: Thomas Zimmermann <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Philipp Stanner <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
Reviewed-by: Thomas Zimmermann <[email protected]>
Acked-by: Dave Airlie <[email protected]>
|
|
pcim_iomap_regions() is a complicated function that uses a bit mask to
determine the BARs the user wishes to request and ioremap. Almost all users
only ever set a single bit in that mask, making that mechanism
questionable.
pcim_iomap_region() is now available as a more simple replacement.
Make pcim_iomap_region() a public function.
Mark pcim_iomap_regions() as deprecated.
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Philipp Stanner <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
|
|
vboxvideo currently does not reserve its PCI BAR through a region request.
Implement the request through the managed function pcim_request_region().
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Philipp Stanner <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
Tested-by: Hans de Goede <[email protected]>
Reviewed-by: Hans de Goede <[email protected]>
Acked-by: Hans de Goede <[email protected]>
|
|
pcim_request_region() is the managed counterpart of pci_request_region().
It is currently only used internally for PCI.
It can be useful for a number of drivers and exporting it is a step towards
deprecating more complicated functions.
Make pcim_request_region() a public function.
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Philipp Stanner <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
Tested-by: Hans de Goede <[email protected]>
Reviewed-by: Hans de Goede <[email protected]>
Acked-by: Hans de Goede <[email protected]>
|
|
Bjorn suggests using pdev->dev.groups for attribute_groups constructed on
PCI device enumeration:
"Is it feasible to build an attribute group in pci_doe_init() and
add it to dev->groups so device_add() will automatically add them?"
https://lore.kernel.org/r/20231019165829.GA1381099@bhelgaas
Unfortunately on s390, pcibios_device_add() usurps pdev->dev.groups for
arch-specific attribute_groups, preventing its use for anything else.
Introduce an ARCH_PCI_DEV_GROUPS macro which arches can define in
<asm/pci.h>. The macro is visible in drivers/pci/pci-sysfs.c through the
inclusion of <linux/pci.h>, which in turn includes <asm/pci.h>.
On s390, define the macro to the three attribute_groups previously assigned
to pdev->dev.groups. Thereby pdev->dev.groups is made available for use by
the PCI core.
As a side effect, arch/s390/pci/pci_sysfs.c no longer needs to be compiled
into the kernel if CONFIG_SYSFS=n.
Link: https://lore.kernel.org/r/7b970f7923e373d1b23784721208f93418720485.1722870934.git.lukas@wunner.de
Signed-off-by: Lukas Wunner <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
Acked-by: Niklas Schnelle <[email protected]>
|
|
The dax is only supported on pfn type pmem devices since commit
f467fee48da4 ("block: move the dax flag to queue_limits"). Trying
to mount DAX filesystem fails with this error:
mount: : wrong fs type, bad option, bad superblock on /dev/pmem7,
missing codepage or helper program, or other error.
dmesg(1) may have more information after failed mount system call.
dmesg: EXT4-fs (pmem7): DAX unsupported by block device.
Fix the problem by adding dax flag setting for the missed case.
Fixes: f467fee48da4 ("block: move the dax flag to queue_limits")
Signed-off-by: Zhihao Cheng <[email protected]>
Reviewed-by: Christoph Hellwig <[email protected]>
Reviewed-by: Dave Jiang <[email protected]>
Reviewed-by: Ira Weiny <[email protected]>
Tested-by: Ira Weiny <[email protected]>
Tested-by: Alison Schofield <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Ira Weiny <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fix from Rafael Wysocki:
"Change the default EPP (energy-performence preference) value for the
Emerald Rapids processor in the intel_pstate driver.
Thisshould improve both the performance and energy efficiency (Pedro
Henrique Kopper)"
* tag 'pm-6.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: intel_pstate: Update Balance performance EPP for Emerald Rapids
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"There are three sets of patches for the soc tree:
- Marek Behún addresses multiple build time regressions caused by
changes to the cznic turris-omnia support
- Dmitry Torokhov fixes a regression in the legacy "gumstix" board
code he cleaned up earlier
- The TI K3 maintainers found multiple bugs in the in gpio, audio and
pcie devicetree nodes"
* tag 'arm-fixes-6.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: pxa/gumstix: fix attaching properties to vbus gpio device
doc: platform: cznic: turris-omnia-mcu: Use double backticks for attribute value
doc: platform: cznic: turris-omnia-mcu: Fix sphinx-build warning
platform: cznic: turris-omnia-mcu: Make GPIO code optional
platform: cznic: turris-omnia-mcu: Make poweroff and wakeup code optional
platform: cznic: turris-omnia-mcu: Make TRNG code optional
platform: cznic: turris-omnia-mcu: Make watchdog code optional
arm64: dts: ti: k3-j784s4-main: Correct McASP DMAs
arm64: dts: ti: k3-j722s: Fix gpio-range for main_pmx0
arm64: dts: ti: k3-am62p: Fix gpio-range for main_pmx0
arm64: dts: ti: k3-am62p: Add gpio-ranges for mcu_gpio0
arm64: dts: ti: k3-am62-verdin-dahlia: Keep CTRL_SLEEP_MOCI# regulator on
arm64: dts: ti: k3-j784s4-evm: Consolidate serdes0 references
arm64: dts: ti: k3-j784s4-evm: Assign only lanes 0 and 1 to PCIe1
|
|
Pull block fixes from Jens Axboe:
"Just a set of cleanups for blk-throttle and nvme structures"
* tag 'block-6.11-20240809' of git://git.kernel.dk/linux:
nvme: reorganize nvme_ns_head fields
nvme: change data type of lba_shift
nvme: remove a field from nvme_ns_head
nvme: remove unused parameter
blk-throttle: remove more latency dead-code
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/andi.shyti/linux into i2c/for-current
Two fixes on the Qualcomm GENI I2C controller are cleaning up the
error exit patch in the runtime_resume() function. The first is
disabling the clock, the second disables the icc on the way out.
|
|
Reset the reception buffer max size when a voltage domain description
request fails, for example when the voltage domain returns an access
permission error (SCMI_ERR_ACCESS) unless what only a single 32bit
word is read back for the remaining voltage description requests
responses leading to invalid information. The side effect of this
issue is that the voltage regulators registered from those remaining
SCMI voltage domain were assigned a wrong regulator name.
Signed-off-by: Etienne Carriere <[email protected]>
Reviewed-by: Cristian Marussi <[email protected]>
Message-Id: <[email protected]>
Signed-off-by: Sudeep Holla <[email protected]>
|
|
It is sometimes useful to reset all these SCMI communication debug
metrics especially when we are interested in analysing these metrics
during a particular workload or for a fixed time duration. Let us
add the capability to reset all these metrics as once so that they
can be counted during the period of interest.
Signed-off-by: Luke Parkin <[email protected]>
Reviewed-by: Cristian Marussi <[email protected]>
Tested-by: Cristian Marussi <[email protected]>
Message-Id: <[email protected]>
Signed-off-by: Sudeep Holla <[email protected]>
|