| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The bulk transfer is VCHIQ_BULK_MODE_WAITING is used by VCHIQ ioctl
interface. It is factored out to a separate function from
vchiq_bulk_transfer() to bulk_xfer_waiting_interruptible().
This is a part of vchiq_bulk_transfer refactoring. Each bulk mode
will have their dedicated functions to execute bulk transfers.
Each mode will be handled separately in subsequent patches.
bulk_xfer_waiting_interruptible() is suffixed with "_interruptible"
to denote that it can be interrupted when a signal is received.
-EAGAIN maybe returned in those cases, similar to what
vchiq_bulk_transfer() does.
Adjust the vchiq_irq_queue_bulk_tx_rx() in the vchiq-dev.c to call
bulk_xfer_waiting_interruptible() for waiting mode. A temporary
goto label has been introduced to jump the call execution over
vchiq_bulk_transfer() for waiting mode only. When all dedicated bulk
transfer calls are introduced, this label shall be dropped.
No function changes intended in this patch.
Signed-off-by: Umang Jain <[email protected]>
Tested-by: Stefan Wahren <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Apple's older A7-A9 SoCs seems to use bit 3 in UTRSTAT as RXTO, which is
enabled by bit 11 in UCON.
Access these bits in addition to the original RXTO and RXTO enable bits,
to allow serial rx to function on A7-A9 SoCs. This change does not
appear to affect the A10 SoC and up.
Tested-by: Janne Grunau <[email protected]>
Reviewed-by: Neal Gompa <[email protected]>
Signed-off-by: Nick Chan <[email protected]>
Reviewed-by: Andi Shyti <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Apple's earlier SoCs, like A7-A11, requires 32-bit writes for the serial
port. Otherwise, a SError happens when writing to UTXH (+0x20). This only
manifested in earlycon as reg-io-width in the device tree is consulted
for normal serial writes.
Change the iotype of the port to UPIO_MEM32, to allow the serial port to
function on A7-A11 SoCs. This change does not appear to affect Apple M1 and
above.
Reviewed-by: Krzysztof Kozlowski <[email protected]>
Reviewed-by: Neal Gompa <[email protected]>
Tested-by: Janne Grunau <[email protected]>
Signed-off-by: Nick Chan <[email protected]>
Reviewed-by: Andi Shyti <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The write to RP2_GLOBAL_CMD followed by an immediate read of
RP2_GLOBAL_CMD in rp2_reset_asic() is intented to flush out the write,
however by then the device is already in reset and cannot respond to a
memory cycle access.
On platforms such as the Raspberry Pi 4 and others using the
pcie-brcmstb.c driver, any memory access to a device that cannot respond
is met with a fatal system error, rather than being substituted with all
1s as is usually the case on PC platforms.
Swapping the delay and the read ensures that the device has finished
resetting before we attempt to read from it.
Fixes: 7d9f49afa451 ("serial: rp2: New driver for Comtrol RocketPort 2 cards")
Cc: stable <[email protected]>
Suggested-by: Jim Quinlan <[email protected]>
Signed-off-by: Florian Fainelli <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Add MODULE_DEVICE_TABLE(), so modules could be properly autoloaded based
on the alias from of_device_id table.
Signed-off-by: Liao Chen <[email protected]>
Acked-by: Uwe Kleine-König <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The polled UART operations are used by the kernel debugger (KDB, KGDB),
which can interrupt the kernel at any point in time. The current
Qualcomm GENI implementation does not really work when there is on-going
serial output as it inadvertently "hijacks" the current tx command,
which can result in both the initial debugger output being corrupted as
well as the corruption of any on-going serial output (up to 4k
characters) when execution resumes:
0190: abcdefghijklmnopqrstuvwxyz0123456789 0190: abcdefghijklmnopqrstuvwxyz0123456789
0191: abcdefghijklmnop[ 50.825552] sysrq: DEBUG
qrstuvwxyz0123456789 0191: abcdefghijklmnopqrstuvwxyz0123456789
Entering kdb (current=0xffff53510b4cd280, pid 640) on processor 2 due to Keyboard Entry
[2]kdb> go
omlji3h3h2g2g1f1f0e0ezdzdycycxbxbwawav :t72r2rp
o9n976k5j5j4i4i3h3h2g2g1f1f0e0ezdzdycycxbxbwawavu:t7t8s8s8r2r2q0q0p
o9n9n8ml6k6k5j5j4i4i3h3h2g2g1f1f0e0ezdzdycycxbxbwawav v u:u:t9t0s4s4rq0p
o9n9n8m8m7l7l6k6k5j5j40q0p p o
o9n9n8m8m7l7l6k6k5j5j4i4i3h3h2g2g1f1f0e0ezdzdycycxbxbwawav :t8t9s4s4r4r4q0q0p
Fix this by making sure that the polled output implementation waits for
the tx fifo to drain before cancelling any on-going longer transfers. As
the polled code cannot take any locks, leave the state variables as they
are and instead make sure that the interrupt handler always starts a new
tx command when there is data in the write buffer.
Since the debugger can interrupt the interrupt handler when it is
writing data to the tx fifo, it is currently not possible to fully
prevent losing up to 64 bytes of tty output on resume.
Fixes: c4f528795d1a ("tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP")
Cc: [email protected] # 4.17
Reviewed-by: Douglas Anderson <[email protected]>
Tested-by: Nícolas F. R. A. Prado <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Disable the GENI interrupts during console writes to reduce the risk of
having interrupt handlers spinning on the port lock on other cores for
extended periods of time.
This can, for example, reduce the total amount of time spent in the
interrupt handler during boot of the x1e80100 CRD by up to a factor nine
(e.g. from 274 ms to 30 ms) while the worst case processing time drops
from 19 ms to 8 ms.
Fixes: c4f528795d1a ("tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP")
Reviewed-by: Douglas Anderson <[email protected]>
Tested-by: Nícolas F. R. A. Prado <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The Qualcomm serial console implementation is broken and can lose
characters when the serial port is also used for tty output.
Specifically, the console code only waits for the current tx command to
complete when all data has already been written to the fifo. When there
are on-going longer transfers this often means that console output is
lost when the console code inadvertently "hijacks" the current tx
command instead of starting a new one.
This can, for example, be observed during boot when console output that
should have been interspersed with init output is truncated:
[ 9.462317] qcom-snps-eusb2-hsphy fde000.phy: Registered Qcom-eUSB2 phy
[ OK ] Found device KBG50ZNS256G KIOXIA Wi[ 9.471743ndows.
[ 9.539915] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
Add a new state variable to track how much data has been written to the
fifo and use it to determine when the fifo and shift register are both
empty. This is needed since there is currently no other known way to
determine when the shift register is empty.
This in turn allows the console code to interrupt long transfers without
losing data.
Note that the oops-in-progress case is similarly broken as it does not
cancel any active command and also waits for the wrong status flag when
attempting to drain the fifo (TX_FIFO_NOT_EMPTY_EN is only set when
cancelling a command leaves data in the fifo).
Fixes: c4f528795d1a ("tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP")
Fixes: a1fee899e5be ("tty: serial: qcom_geni_serial: Fix softlock")
Fixes: 9e957a155005 ("serial: qcom-geni: Don't cancel/abort if we can't get the port lock")
Cc: [email protected] # 4.17
Reviewed-by: Douglas Anderson <[email protected]>
Tested-by: Nícolas F. R. A. Prado <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
With a small modification the qcom_geni_serial_poll_bit() function
could be used to poll more than just a single bit. Let's generalize
it. We'll make the qcom_geni_serial_poll_bit() into just a wrapper of
the general function.
Signed-off-by: Douglas Anderson <[email protected]>
Reviewed-by: Konrad Dybcio <[email protected]>
Link: https://lore.kernel.org/r/20240610152420.v4.5.Ic6411eab8d9d37acc451705f583fb535cd6dadb2@changeid
Tested-by: Nícolas F. R. A. Prado <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The "offset" passed in should be unsigned since it's always a positive
offset from our memory mapped IO.
The "field" should be u32 since we're anding it with a 32-bit value
read from the device.
Suggested-by: Stephen Boyd <[email protected]>
Signed-off-by: Douglas Anderson <[email protected]>
Reviewed-by: Konrad Dybcio <[email protected]>
Link: https://lore.kernel.org/r/20240610152420.v4.4.I24a0de52dd7336908df180fa6b698e001f3aff82@changeid
Tested-by: Nícolas F. R. A. Prado <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Commit 663abb1a7a7f ("tty: serial: qcom_geni_serial: Fix UART hang")
addressed an issue with stalled tx after the console code interrupted
the last bytes of a tx command by reenabling the watermark interrupt if
there is data in write buffer. This can however break software flow
control by re-enabling tx after the user has stopped it.
Address the original issue by not clearing the CMD_DONE flag after
polling for command completion. This allows the interrupt handler to
start another transfer when the CMD_DONE interrupt has not been disabled
due to flow control.
Fixes: c4f528795d1a ("tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP")
Fixes: 663abb1a7a7f ("tty: serial: qcom_geni_serial: Fix UART hang")
Cc: [email protected] # 4.17
Reviewed-by: Douglas Anderson <[email protected]>
Tested-by: Nícolas F. R. A. Prado <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The qcom_geni_serial_poll_bit() can be used to wait for events like
command completion and is supposed to wait for the time it takes to
clear a full fifo before timing out.
As noted by Doug, the current implementation does not account for start,
stop and parity bits when determining the timeout. The helper also does
not currently account for the shift register and the two-word
intermediate transfer register.
A too short timeout can specifically lead to lost characters when
waiting for a transfer to complete as the transfer is cancelled on
timeout.
Instead of determining the poll timeout on every call, store the fifo
timeout when updating it in set_termios() and make sure to take the
shift and intermediate registers into account. Note that serial core has
already added a 20 ms margin to the fifo timeout.
Also note that the current uart_fifo_timeout() interface does
unnecessary calculations on every call and did not exist in earlier
kernels so only store its result once. This facilitates backports too as
earlier kernels can derive the timeout from uport->timeout, which has
since been removed.
Fixes: c4f528795d1a ("tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP")
Cc: [email protected] # 4.17
Reported-by: Douglas Anderson <[email protected]>
Tested-by: Nícolas F. R. A. Prado <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Streams should flush their TRB cache, re-read TRBs, and start executing
TRBs from the beginning of the new dequeue pointer after a 'Set TR Dequeue
Pointer' command.
Cadence controllers may fail to start from the beginning of the dequeue
TRB as it doesn't clear the Opaque 'RsvdO' field of the stream context
during 'Set TR Dequeue' command. This stream context area is where xHC
stores information about the last partially executed TD when a stream
is stopped. xHC uses this information to resume the transfer where it left
mid TD, when the stream is restarted.
Patch fixes this by clearing out all RsvdO fields before initializing new
Stream transfer using a 'Set TR Dequeue Pointer' command.
Fixes: 3d82904559f4 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
cc: [email protected]
Signed-off-by: Pawel Laszczak <[email protected]>
Reviewed-by: Peter Chen <[email protected]>
Link: https://lore.kernel.org/r/PH7PR07MB95386A40146E3EC64086F409DD9D2@PH7PR07MB9538.namprd07.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The resume operation of Phytium Px210 xHCI host would failed
to restore state. Use the XHCI_RESET_ON_RESUME quirk to skip
it and reset the controller after resume.
Co-developed-by: Chen Baozi <[email protected]>
Signed-off-by: Chen Baozi <[email protected]>
Co-developed-by: Wang Zhimin <[email protected]>
Signed-off-by: Wang Zhimin <[email protected]>
Co-developed-by: Chen Zhenhua <[email protected]>
Signed-off-by: Chen Zhenhua <[email protected]>
Co-developed-by: Wang Yinfeng <[email protected]>
Signed-off-by: Wang Yinfeng <[email protected]>
Co-developed-by: Jiakun Shuai <[email protected]>
Signed-off-by: Jiakun Shuai <[email protected]>
Signed-off-by: WangYuli <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Cc: stable <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
SS_CON and U3 wakeup need 'ref_clk' on. iMX8MP turn off it while system
sleep, So disable these wakeup source and only enable DP/DM wakeup source
for host mode.
Reviewed-by: Xu Yang <[email protected]>
Signed-off-by: Li Jun <[email protected]>
Acked-by: Thinh Nguyen <[email protected]>
Signed-off-by: Frank Li <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Add 2 software manage quirk properties (xhci-missing-cas-quirk and
xhci-skip-phy-init-quirk) for xhci host.
dwc3 driver have PHY management to cover both device and host mode, so add
xhci-skip-phy-init-quirk to skip PHY management from HCD core.
Cold Attach Status (CAS) bit can't be set at i.MX8MP after resume from
suspend state. So set xhci-missing-cas-quirk.
Signed-off-by: Frank Li <[email protected]>
Acked-by: Thinh Nguyen <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Parse software managed property 'xhci-skip-phy-init-quirk' and
'xhci-skip-phy-init-quirk' to apply related quirk. It allows usb glue layer
driver apply these quirk.
Signed-off-by: Frank Li <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
usb5744 supports SMBus Configuration and it may be configured via the
SMBus slave interface during the hub start-up configuration stage.
To program it driver uses i2c-bus phandle (added in commit '02be19e914b8
dt-bindings: usb: Add support for Microchip usb5744 hub controller') to
get i2c client device and then based on usb5744 compatible check calls
usb5744 i2c default initialization sequence.
Apart from the USB command attach, prevent the hub from suspend.
when the USB Attach with SMBus (0xAA56) command is issued to the hub,
the hub is getting enumerated and then it puts in a suspend mode.
This causes the hub to NAK any SMBus access made by the SMBus Master
during this period and not able to see the hub's slave address while
running the "i2c probe" command.
Prevent the MCU from putting the HUB in suspend mode through register
write. The BYPASS_UDC_SUSPEND bit (Bit 3) of the RuntimeFlags2
register at address 0x411D controls this aspect of the hub. The
BYPASS_UDC_SUSPEND bit in register 0x411Dh must be set to ensure that the
MCU is always enabled and ready to respond to SMBus runtime commands.
This register needs to be written before the USB attach command is issued.
The byte sequence is as follows:
Slave addr: 0x2d 00 00 05 00 01 41 1D 08
Slave addr: 0x2d 99 37 00
Slave addr: 0x2d AA 56 00
Also since usb5744 i2c initialization routine uses i2c SMBus APIs invoke
these APIs only when i2c driver is enabled in the kernel configuration.
Signed-off-by: Radhey Shyam Pandey <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Introduce dedicated field 'power_on_delay_us' in onboard platform data
and update its delay for USB5744 configuration. Hub itself requires some
delay after reset to get to state where configuration data is going to
be accepted. Without delay upcoming support for configuration via SMBUS
is reporting a failure on the first SMBus write.
i2c 2-002d: error -ENXIO: BYPASS_UDC_SUSPEND bit configuration failed
Similar delay is likely also required for default configuration but
because there is enough time (code execution) between reset and usage
of the hub any issue is not visible but it doesn't mean delay shouldn't
be reflected.
Signed-off-by: Radhey Shyam Pandey <[email protected]>
Suggested-by: Matthias Kaehlcke <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The dwc2_handle_usb_suspend_intr() function disables gadget clocks in USB
peripheral mode when no other power-down mode is available (introduced by
commit 0112b7ce68ea ("usb: dwc2: Update dwc2_handle_usb_suspend_intr function.")).
However, the dwc2_drd_role_sw_set() USB role update handler attempts to
read DWC2 registers if the USB role has changed while the USB is in suspend
mode (when the clocks are gated). This causes the system to hang.
Release the gadget clocks before handling the USB role update.
Fixes: 0112b7ce68ea ("usb: dwc2: Update dwc2_handle_usb_suspend_intr function.")
Cc: [email protected]
Signed-off-by: Tomas Marek <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Fix changes incorrect usb_request->status returned during disabling
endpoints. Before fix the status returned during dequeuing requests
while disabling endpoint was ECONNRESET.
Patch change it to ESHUTDOWN.
Patch fixes issue detected during testing UVC gadget.
During stopping streaming the class starts dequeuing usb requests and
controller driver returns the -ECONNRESET status. After completion
requests the class or application "uvc-gadget" try to queue this
request again. Changing this status to ESHUTDOWN cause that UVC assumes
that endpoint is disabled, or device is disconnected and stops
re-queuing usb requests.
Fixes: 3d82904559f4 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
cc: [email protected]
Signed-off-by: Pawel Laszczak <[email protected]>
Reviewed-by: Peter Chen <[email protected]>
Link: https://lore.kernel.org/r/PH7PR07MB9538E8CA7A2096AAF6A3718FDD9E2@PH7PR07MB9538.namprd07.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
TCPCI USB PHY - PTN5110 could be used with SOCs that only support
the edge-triggered GPIO interrupts such as TI's K3 device AM69.
Move the interrupt configuration to the firmware which would
allow to accommodate edge triggered interrupts for such SOCs.
In order to support the edge interrupts, register irq line in advance
and keep track of occurrence during port registering.
When the edge interrupts are used, it is observed that some of the
interrupts are missed when tcpci_irq() is serving the current
interrupt. Therefore, check the status register at the end of
tcpci_irq() and re-run the function if the status is not clear
i.e. pending interrupt.
Signed-off-by: Emanuele Ghidoli <[email protected]>
Signed-off-by: Parth Pancholi <[email protected]>
Reviewed-by: Heikki Krogerus <[email protected]>
Reviewed-by: Francesco Dolcini <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Fixed coding style issue: unsigned to unsigned int.
Signed-off-by: Andreas Kühn <[email protected]>
Acked-by: Peter Chen <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Replace open coded device_property_match_property_string().
Signed-off-by: Andy Shevchenko <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The syzbot reported a kernel-usb-infoleak in usbtmc_write,
we need to clear the structure before filling fields.
Fixes: 4ddc645f40e9 ("usb: usbtmc: Add ioctl for vendor specific write")
Reported-and-tested-by: [email protected]
Closes: https://syzkaller.appspot.com/bug?extid=9d34f80f841e948c3fdb
Signed-off-by: Edward Adam Davis <[email protected]>
Cc: stable <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The combination of dev_err() and the returned error code could be
replaced by dev_err_probe() in driver's probe function. Let's,
converting to dev_err_probe() to make code more simple.
Signed-off-by: Lin Ruifeng <[email protected]>
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
Reviewed-by: Matthias Brugger <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial device id for 6.12-rc1
Here's a new pl2303 device id.
This one has been in linux-next with no reported issues.
* tag 'usb-serial-6.12-rc1-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: pl2303: add device id for Macrosilicon MS3020
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for 6.12-rc1
Here are the USB-serial updates for 6.12-rc1, including:
- fix kobil_sct initial terminal settings
- set driver owner when registering drivers
All have been in linux-next with no reported issues.
* tag 'usb-serial-6.12-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: kobil_sct: restore initial terminal settings
USB: serial: drop driver owner initialization
USB: serial: set driver owner when registering drivers
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-next
Mika writes:
thunderbolt: Changes for v6.12 merge window
This includes following USB4/Thunderbolt changes for the v6.12 merge
window:
- Improvements for software receiver lane margining
- Enable support for optional voltage offset range for receiver lane
margining.
All these have been in linux-next with no reported issues.
* tag 'thunderbolt-for-v6.12-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt:
thunderbolt: Improve software receiver lane margining
thunderbolt: Add optional voltage offset range for receiver lane margining
thunderbolt: Consolidate margining parameters into a structure
thunderbolt: Add missing usb4_port_sb_read() to usb4_port_sw_margin()
|
|
On some newer laptops ASUS laptops SPS support is advertised but not
actually used, causing the AMD driver to register as a platform_profile
handler.
If this happens then the asus_wmi driver would error with -EEXIST when
trying to register its own handler leaving the user with a possibly
unusable system. This is especially true for laptops with an MCU that emit
a stream of HID packets, some of which can be misinterpreted as shutdown
signals.
We can safely continue loading the driver instead of bombing out.
Signed-off-by: Luke D. Jones <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Reviewed-by: Hans de Goede <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
|
|
Add more verbose debug print in the WMI method calls. This helps a lot
with debugging various issues working with regular users as the WMI
methods can be traced now.
Signed-off-by: Luke D. Jones <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Reviewed-by: Hans de Goede <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
|
|
This is a platform/x86 library that can only be used on x86 devices.
so it makes sense that it lives under the platform_data/x86/ directory
instead.
No functional changes intended.
Signed-off-by: Andy Shevchenko <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Reviewed-by: Hans de Goede <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
|
|
This is a platform/x86 library that is mostly being used by other
drivers not directly under arch/x86 anyway (with the exception of the
Intel MID setup code) so it makes sense that it lives under the
platform_data/x86/ directory instead.
No functional changes intended.
Suggested-by: Andy Shevchenko <[email protected]>
Signed-off-by: Mika Westerberg <[email protected]>
Signed-off-by: Andy Shevchenko <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Reviewed-by: Hans de Goede <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
|
|
The value returned by "HINF" contains press/release information
in bit 7 and a keycode in bits 0-6.
Change the code to retrieve the keycode to use all 7 keycode bits instead
of only using bits 0-3 and add mappings for the higher keycodes used by
the programmable buttons found on newer panasonic toughbook models.
Tested-by: James Harmison <[email protected]>
Signed-off-by: James Harmison <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Since the debugfs_create_dir() never returns a null pointer, checking
the return value for a null pointer is redundant. Since
debugfs_create_file() can deal with a ERR_PTR() style pointer, drop
the check.
Signed-off-by: Li Zetao <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Reviewed-by: Hans de Goede <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
|
|
This applies similar quirks used by previous generation device, so that
Trackpoint and buttons on the touchpad works. New USB KBD PID 0x61AE for
Thinkpad X12 Tab is added.
Signed-off-by: Vishnu Sankar <[email protected]>
Reviewed-by: Mark Pearson <[email protected]>
Signed-off-by: Jiri Kosina <[email protected]>
|
|
Add support to ignore all LTRs before suspend and restore the previous
LTR values after suspend. This feature could be turned off with module
parameter ltr_ignore_all_suspend.
LTR value is a mechanism for a device to indicate tolerance to access
the corresponding resource. When system suspends, the resource is not
available and therefore the LTR value could be ignored. Ignoring all
LTR values prevents problematic device from blocking the system to get
to the deepest package state during suspend.
Suggested-by: Rafael J. Wysocki <[email protected]>
Signed-off-by: Xi Pardee <[email protected]>
Reviewed-by: Ilpo Järvinen <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Hans de Goede <[email protected]>
|
|
sb_mac() verifies that the superblock + MAC don't exceed 512 bytes.
Because the superblock is currently 64 bytes, this really verifies
mac_size <= 448. This confuses smatch into thinking that mac_size may
be as large as 448, which is inconsistent with the later code that
assumes the MAC fits in a buffer of size HASH_MAX_DIGESTSIZE (64).
In fact mac_size <= HASH_MAX_DIGESTSIZE is guaranteed by the crypto API,
as that is the whole point of HASH_MAX_DIGESTSIZE. But, let's be
defensive and explicitly check for this. This suppresses the false
positive smatch warning. It does not fix an actual bug.
Reported-by: kernel test robot <[email protected]>
Reported-by: Dan Carpenter <[email protected]>
Closes: https://lore.kernel.org/r/[email protected]/
Signed-off-by: Eric Biggers <[email protected]>
Signed-off-by: Mikulas Patocka <[email protected]>
|
|
Implicit MRs in ODP memory scheme require allocating a private null mkey
and assigning the mkey and va differently in the KSM mkey.
The page faults are received on the null mkey so we also add storing the
null mkey in the odp_mkey xarray.
Signed-off-by: Michael Guralnik <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Leon Romanovsky <[email protected]>
|
|
The memory scheme page fault event is a new approch in handling page fault
on mkeys using the on-demand-paging feature.
The major shift in handling the page fault in this scheme is that the HW
is taking responsibilty for parsing the faulted mkey instead of the
previous approach where the driver would read and parse the wqes and
query the mkeys to get to the direct mkey that we need to handle.
Therefore, the event we get from FW in this scheme will contain the
direct mkey and address we need to handle and require much less work
from driver.
Additionally, to optimize performance, the FW can generate the event on
a memory area that is larger than the faulted memory operation is
requiring, to 'prefetch' memory that is around it and will likely be
used soon.
Unlike previous types of page fault, the memory page scheme fault does
not always require a resume command after handling the page fault as the FW
can post multiple events on same mkey and will set the 'last' flag only on
the page fault that requires the resume command.
Signed-off-by: Michael Guralnik <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Leon Romanovsky <[email protected]>
|
|
Split the search for the ODP mkey when handling an rdma type page fault to
a helper function, later to be used in other page fault types.
Signed-off-by: Michael Guralnik <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Leon Romanovsky <[email protected]>
|
|
The new memory scheme page faults are requesting the driver to fetch
additinal pages to the faulted memory access.
This is done in order to prefetch pages before and after the area that
got the page fault, assuming this will reduce the total amount of page
faults.
The driver should ensure it handles only the pages that are within the
umem range.
Signed-off-by: Michael Guralnik <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Leon Romanovsky <[email protected]>
|
|
Add new fields to support the new memory scheme page fault and extend
the token field to u64 as in the new scheme the token is 48 bit.
Signed-off-by: Michael Guralnik <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Leon Romanovsky <[email protected]>
|
|
Expose IFC bits to support the new memory scheme on demand paging.
Change the macro reading odp capabilities to be able to read from the
new IFC layout and align the code in upper layers to be compiled.
Signed-off-by: Michael Guralnik <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Leon Romanovsky <[email protected]>
|
|
Protect the usage of the 6th bit with the relevant capability to ensure
we are using the new page sizes with FW that supports the bit extension.
Signed-off-by: Michael Guralnik <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Leon Romanovsky <[email protected]>
|
|
Use the wrapper function for getting the driver data using pci_dev
instead of using dev_get_drvdata() with &pdev->dev, so we can directly
pass a struct pci_dev. This is a purely cosmetic change.
Reviewed-by: Andi Shyti <[email protected]>
Signed-off-by: Andy Shevchenko <[email protected]>
Signed-off-by: Andi Shyti <[email protected]>
|
|
Propagate firmware node by using a specific API call, i.e. device_set_node().
Reviewed-by: Andi Shyti <[email protected]>
Signed-off-by: Andy Shevchenko <[email protected]>
Acked-by: Jarkko Nikula <[email protected]>
Tested-by: Serge Semin <[email protected]>
Signed-off-by: Andi Shyti <[email protected]>
|
|
Since i2c_dw_probe() is going to be extended, uninline it to reduce
the noise in the common header.
Reviewed-by: Andi Shyti <[email protected]>
Signed-off-by: Andy Shevchenko <[email protected]>
Acked-by: Jarkko Nikula <[email protected]>
Tested-by: Serge Semin <[email protected]>
Signed-off-by: Andi Shyti <[email protected]>
|
|
Merge series from Krzysztof Kozlowski <[email protected]>:
Few cleanups (safer code), built tested. Last two patches should
probably be tested.
|
|
Add support to ethtool phylink functions:
- get/set settings like speed, duplex etc
- get/set the wake-on-lan (WOL)
- get/set the energy-efficient ethernet (EEE)
- get/set the pause
Reviewed-by: Andrew Lunn <[email protected]>
Signed-off-by: Raju Lakkaraju <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|