| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
[Why]
When the link BW is smaller than the request BW,
the DP LT just kept running and fallback to lower link config.
DP LT just aborted if is_hpd_pending bit is high.
But is_hpd_pending bit indicates a new HPD event received.
It doesn't mean the HPD is low.
[How]
Abort the DP LT if the link BW is smaller than the request BW.
Remove checking is_hpd_pending bit in DP LT.
Reviewed-by: Wenjing Liu <[email protected]>
Acked-by: Roman Li <[email protected]>
Signed-off-by: Cruise <[email protected]>
Tested-by: Daniel Wheeler <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
[WHY&HOW]
At the time of block sequence construction, the exact reference DPP/DISP clock is
not yet known, so the clock should be passed by reference to the DTO programming
function.
Reviewed-by: Alvin Lee <[email protected]>
Acked-by: Roman Li <[email protected]>
Signed-off-by: Dillon Varone <[email protected]>
Tested-by: Daniel Wheeler <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
[WHY&HOW]
Disable to improve stability for now.
Reviewed-by: Alvin Lee <[email protected]>
Acked-by: Roman Li <[email protected]>
Signed-off-by: Dillon Varone <[email protected]>
Tested-by: Daniel Wheeler <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
[Description]
There is a corner case where we're in an ODM config that
has recout.x != 0. In these scenarios we have to take into
account the extra offset in the ODM adjustment for cursor.
Reviewed-by: Aric Cyr <[email protected]>
Acked-by: Roman Li <[email protected]>
Signed-off-by: Alvin Lee <[email protected]>
Tested-by: Daniel Wheeler <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
[why]
A recent change for ODM combine refactor contains a typo which causes ODM
combine mode programmed incorrectly.
Reviewed-by: George Shen <[email protected]>
Acked-by: Roman Li <[email protected]>
Signed-off-by: Wenjing Liu <[email protected]>
Tested-by: Daniel Wheeler <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
[Why]
Disable idle optimization for each atomic commit is unnecessary,
and can lead to a potential race condition.
[How]
Remove idle optimization check from amdgpu_dm_atomic_commit_tail()
Fixes: 196107eb1e15 ("drm/amd/display: Add IPS checks before dcn register access")
Cc: [email protected]
Reviewed-by: Hamza Mahfooz <[email protected]>
Acked-by: Roman Li <[email protected]>
Signed-off-by: Roman Li <[email protected]>
Tested-by: Daniel Wheeler <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
[Why]
Missing check for when there is new pipe configuration but both cur_pipe
and new_pipe are both populated causing update_state of DSC for that
instance not being updated correctly.
This causes some display mode changes to cause underflow since DSCCLK
is still gated when the display requires DSC.
[How]
Added another condition in the new pipe addition branch that checks if
there is a new pipe configuration and if it is not the same as cur_pipe.
cur_pipe does not necessarily have to be NULL to go in this branch.
Reviewed-by: Nicholas Kazlauskas <[email protected]>
Acked-by: Roman Li <[email protected]>
Signed-off-by: Nicholas Susanto <[email protected]>
Tested-by: Daniel Wheeler <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
[Why]
For debugging and testing purposes.
[How]
If IPS is supported create ips_status debugfs entry.
Usage: cat /sys/kernel/debug/dri/0/amdgpu_dm_ips_status
Reviewed-by: Jerry Zuo <[email protected]>
Acked-by: Roman Li <[email protected]>
Signed-off-by: Roman Li <[email protected]>
Tested-by: Daniel Wheeler <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
[Why]
Reset the shared dmub firmware region on dmub hw init to start with
known state.
[How]
Memset the shared region to 0 in dmub_hw_init().
Suggested-by: Nicholas Kazlauskas <[email protected]>
Reviewed-by: Nicholas Kazlauskas <[email protected]>
Signed-off-by: Roman Li <[email protected]>
Tested-by: Daniel Wheeler <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
[Why/How]
Need to be able to trigger a DMA load to update 3DLUT contents in MPC.
Adding a HWSS function to serve as the trigger.
Reviewed-by: Krunoslav Kovac <[email protected]>
Acked-by: Roman Li <[email protected]>
Signed-off-by: Ilya Bakoulin <[email protected]>
Tested-by: Daniel Wheeler <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
[Why]
DML 2.1 allocates two types of memory in its ctx structure but does not
destroy them, causing memory leak whenever DML 2.1 instance is created
and destroyed.
[How]
Deallocate two instances of allocated memory whenever DML 2.1 is
destroyed.
Reviewed-by: Rodrigo Siqueira <[email protected]>
Signed-off-by: Chris Park <[email protected]>
Tested-by: Daniel Wheeler <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
[Why] Coverity reports NULL_RETURN warning.
[How] Add pointer NULL check.
Reviewed-by: Rodrigo Siqueira <[email protected]>
Signed-off-by: Hersen Wu <[email protected]>
Tested-by: Daniel Wheeler <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
update driver-if interface for smu 14.0.2/3
Signed-off-by: Kenneth Feng <[email protected]>
Reviewed-by: Yang Wang <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
Acked-by: Roman Li <[email protected]>
Signed-off-by: Rodrigo Siqueira <[email protected]>
Tested-by: Daniel Wheeler <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
Need to select DTBCLK and DPREFCLK as DTBCLK_p source according to
hardware guidance.
Reviewed-by: Rodrigo Siqueira <[email protected]>
Signed-off-by: Dillon Varone <[email protected]>
Tested-by: Daniel Wheeler <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
[why]
Cleaning up the code refactor requires hubbub to be in its own
component.
[how]
Move all DCN401 files under newly created hubbub folder and fixing the
makefiles.
Reviewed-by: Rodrigo Siqueira <[email protected]>
Signed-off-by: Harikrishna Revalla <[email protected]>
Tested-by: Daniel Wheeler <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
[Why]
Enable adaptive scaler support for DCN401
[How]
- Enable build flag for SPL
- Set prefer_easf flag to true
- Apply light linear scaling policy based on transfer function and pixel
format. Choose between linear or non-linear scaling
- Set matrix_mode based on pixel format
- Disable ring estimator
- Add missing EASF register defines, masks, and writes
- Disable EASF if scale ratio or number of taps is unsupported and when
bypassing the scaler
- Add debug flags and registry keys for debugging SPL and EASF
- Add support for Visual Confirm with EASF
Reviewed-by: Rodrigo Siqueira <[email protected]>
Signed-off-by: Samson Tam <[email protected]>
Tested-by: Daniel Wheeler <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
This fixes indentations and adjust spaces for better readability and
code styles.
Reviewed-by: Rodrigo Siqueira <[email protected]>
Signed-off-by: Alex Hung <[email protected]>
Tested-by: Daniel Wheeler <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
[Why]
DVI is TMDS signal like HDMI but without audio. Current signal check
does not correctly reflect DVI clock programming.
[How]
Define a new signal check for TMDS that includes DVI to HDMI TMDS
programming.
Reviewed-by: Rodrigo Siqueira <[email protected]>
Signed-off-by: Chris Park <[email protected]>
Tested-by: Daniel Wheeler <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
The comparisons intend to be DCN401 inclusive, and fix it by adding
equal signs.
Reviewed-by: Rodrigo Siqueira <[email protected]>
Signed-off-by: Alex Hung <[email protected]>
Tested-by: Daniel Wheeler <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
The functions are missing. These two functions are required to support
MST.
Reviewed-by: Rodrigo Siqueira <[email protected]>
Signed-off-by: Wenjing Liu <[email protected]>
Tested-by: Daniel Wheeler <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
The function that commits planes calls the same set of functions twice,
and in the case of the FAMs utilization, it is not desired to call the
dmub, hwss_build and hwss_execute. This commit just removes the
unnecessary calls to those functions.
Acked-by: Roman Li <[email protected]>
Signed-off-by: Rodrigo Siqueira <[email protected]>
Tested-by: Daniel Wheeler <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
Move dsc functions from dc.c to dc_dsc.c.
Co-developed-by: George Shen <[email protected]>
Signed-off-by: George Shen <[email protected]>
Signed-off-by: Wenjing Liu <[email protected]>
Reviewed-by: Rodrigo Siqueira <[email protected]>
Tested-by: Daniel Wheeler <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
Commit 4f563a64732d ("block: add a max_user_discard_sectors queue
limit") changed block core to set max_discard_sectors to:
min(lim->max_hw_discard_sectors, lim->max_user_discard_sectors)
Since commit 1c0e720228ad ("dm: use queue_limits_set") it was reported
dm-thinp was failing in a few fstests (generic/347 and generic/405)
with the first WARN_ON_ONCE in dm_cell_key_has_valid_range() being
reported, e.g.:
WARNING: CPU: 1 PID: 30 at drivers/md/dm-bio-prison-v1.c:128 dm_cell_key_has_valid_range+0x3d/0x50
blk_set_stacking_limits() sets max_user_discard_sectors to UINT_MAX,
so given how block core now sets max_discard_sectors (detailed above)
it follows that blk_stack_limits() stacks up the underlying device's
max_hw_discard_sectors and max_discard_sectors is set to match it. If
max_hw_discard_sectors exceeds dm's BIO_PRISON_MAX_RANGE, then
dm_cell_key_has_valid_range() will trigger the warning with:
WARN_ON_ONCE(key->block_end - key->block_begin > BIO_PRISON_MAX_RANGE)
Aside from this warning, the discard will fail. Fix this and other DM
issues by governing discard support in terms of max_hw_discard_sectors
instead of max_discard_sectors.
Reported-by: Theodore Ts'o <[email protected]>
Fixes: 1c0e720228ad ("dm: use queue_limits_set")
Signed-off-by: Mike Snitzer <[email protected]>
|
|
dm-integrity could set discard_granularity lower than the logical block
size. This could result in failures when sending discard requests to
dm-integrity.
This fix is needed for kernels prior to 6.10.
Signed-off-by: Mikulas Patocka <[email protected]>
Reported-by: Eric Wheeler <[email protected]>
Cc: [email protected] # <= 6.9
Signed-off-by: Mike Snitzer <[email protected]>
|
|
V3D_PERFCNT_NUM represents the maximum number of performance counters
for V3D 4.2, but not for V3D 7.1. This means that, if we use
V3D_PERFCNT_NUM, we might go out-of-bounds on V3D 7.1.
Therefore, use the number of performance counters on V3D 7.1 as the
maximum number of counters. This will allow us to create arrays on the
stack with reasonable size. Note that userspace must use the value
provided by DRM_V3D_PARAM_MAX_PERF_COUNTERS.
Signed-off-by: Maíra Canal <[email protected]>
Reviewed-by: Iago Toral Quiroga <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Userspace usually needs some information about the performance counters
available. Although we could replicate this information in the kernel
and user-space, let's use the kernel as the "single source of truth" to
avoid issues in the future (e.g. list of performance counters is updated
in user-space, but not in the kernel, generating invalid requests).
Therefore, create a new IOCTL to expose the performance counters
information, that is name, category, and description.
Signed-off-by: Maíra Canal <[email protected]>
Reviewed-by: Iago Toral Quiroga <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
The maximum number of performance counters can change from version to
version and it's important for userspace to know this value, as it needs
to use the counters for performance queries. Therefore, expose the
maximum number of performance counters to userspace as a parameter.
Signed-off-by: Maíra Canal <[email protected]>
Reviewed-by: Iago Toral Quiroga <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Currently, even though V3D 7.1 has 93 performance counters, it is not
possible to create counters bigger than 87, as
`v3d_perfmon_create_ioctl()` understands that counters bigger than 87
are invalid.
Therefore, create a device variable to expose the maximum
number of counters for a given V3D version and make
`v3d_perfmon_create_ioctl()` check this variable.
This commit fixes CTS failures in the performance queries tests
`dEQP-VK.query_pool.performance_query.*` [1]
Link: https://gitlab.freedesktop.org/mesa/mesa/-/commit/ea1f09a5f21839f4f3b93610b58507c4bd9b9b81 [1]
Fixes: 6fd9487147c4 ("drm/v3d: add brcm,2712-v3d as a compatible V3D device")
Signed-off-by: Maíra Canal <[email protected]>
Reviewed-by: Iago Toral Quiroga <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Add name, category and description for each one of the 93 performance
counters available on V3D.
Note that V3D 4.2 has 87 performance counters, while V3D 7.1 has 93.
Therefore, there are two performance counters arrays. The index of the
performance counter for each V3D version is represented by its position
on the array.
Signed-off-by: Maíra Canal <[email protected]>
Reviewed-by: Iago Toral Quiroga <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
The data-sheet for TPS6287x-Q1
https://www.ti.com/lit/ds/symlink/tps62873-q1.pdf
states at chapter 9.3.6.1 Output Voltage Range:
"Note that every change to the VRANGE[1:0] bits must be followed by a
write to the VSET register, even if the value of the VSET[7:0] bits does
not change."
The current implementation of the driver uses the
regulator_set_voltage_sel_pickable_regmap() helper which further uses
regmap_update_bits() to write the VSET-register. The
regmap_update_bits() will not access the hardware if the new register
value is same as old. It is worth noting that this is true also when the
register is marked volatile, which I can't say is wrong because
'read-mnodify-write'-cycle with a volatile register is in any case
something user should carefully consider.
The 'range_applied_by_vsel'-flag in regulator desc was added to force
the vsel register upodates by using regmap_write_bits(). This variant
will always unconditionally write the bits to the hardware.
It is worth noting that the vsel is now forced to be written to the
hardware, whether the range was changed or not. This may cause a
performance drop if users are wrtiting same voltage value repeteadly.
It would be possible to read the range register to determine if it was
changed, but this would be a performance issue for users who don't use
reg cache for vsel.
Always write the VSET register to the hardware regardless the cache.
Signed-off-by: Matti Vaittinen <[email protected]>
Fixes: 7b0518fbf2be ("regulator: Add support for TI TPS6287x regulators")
Link: https://msgid.link/r/ZktD50C5twF1EuKu@fedora
Signed-off-by: Mark Brown <[email protected]>
|
|
Some PMICs treat the vsel_reg same as apply-bit. Eg, when voltage range
is changed, the new voltage setting is not taking effect until the vsel
register is written.
Add a flag 'range_applied_by_vsel' to the regulator desc to indicate this
behaviour and to force the vsel value to be written to hardware if range
was changed, even if the old selector was same as the new one.
Signed-off-by: Matti Vaittinen <[email protected]>
Link: https://msgid.link/r/ZktCpcGZdgHWuN_L@fedora
Signed-off-by: Mark Brown <[email protected]>
|
|
git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- optimize DMA sync calls when they are no-ops (Alexander Lobakin)
- fix swiotlb padding for untrusted devices (Michael Kelley)
- add documentation for swiotb (Michael Kelley)
* tag 'dma-mapping-6.10-2024-05-20' of git://git.infradead.org/users/hch/dma-mapping:
dma: fix DMA sync for drivers not calling dma_set_mask*()
xsk: use generic DMA sync shortcut instead of a custom one
page_pool: check for DMA sync shortcut earlier
page_pool: don't use driver-set flags field directly
page_pool: make sure frag API fields don't span between cachelines
iommu/dma: avoid expensive indirect calls for sync operations
dma: avoid redundant calls for sync operations
dma: compile-out DMA sync op calls when not used
iommu/dma: fix zeroing of bounce buffer padding used by untrusted devices
swiotlb: remove alloc_size argument to swiotlb_tbl_map_single()
Documentation/core-api: add swiotlb documentation
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging
Pull dmi updates from Jean Delvare:
"Bug fixes:
- KCFI violation in dmi-id
- stop decoding on broken (short) DMI table entry
New features:
- print info about populated memory slots at boot"
* tag 'dmi-for-v6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
firmware: dmi: Add info message for number of populated and total memory slots
firmware: dmi: Stop decoding on broken entry
firmware: dmi-id: add a release callback function
|
|
git://www.linux-watchdog.org/linux-watchdog
Pull watchdog updates from Wim Van Sebroeck:
- Add Lenovo SE10 platform Watchdog Driver
- Other small fixes and improvements
* tag 'linux-watchdog-6.10-rc1' of git://www.linux-watchdog.org/linux-watchdog:
watchdog: LENOVO_SE10_WDT should depend on X86 && DMI
watchdog: sa1100: Fix PTR_ERR_OR_ZERO() vs NULL check in sa1100dog_probe()
watchdog: rti_wdt: Set min_hw_heartbeat_ms to accommodate a safety margin
watchdog: add HAS_IOPORT dependencies
watchdog/wdt-main: Use cpumask_of() to avoid cpumask var on stack
watchdog: bd9576: Drop "always-running" property
watchdog: mtx-1: drop driver owner assignment
watchdog: cpu5wdt.c: Fix use-after-free bug caused by cpu5wdt_trigger
watchdog: lenovo_se10_wdt: Watchdog driver for Lenovo SE10 platform
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"i2c core removes an argument from the i2c_mux_add_adapter() call to
further deprecate class based I2C device instantiation. All users are
converted, too.
Other that that, Andi collected a number if I2C host driver patches.
Those merges have their own description"
* tag 'i2c-for-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (72 commits)
power: supply: sbs-manager: Remove class argument from i2c_mux_add_adapter()
i2c: mux: Remove class argument from i2c_mux_add_adapter()
i2c: synquacer: Fix an error handling path in synquacer_i2c_probe()
i2c: acpi: Unbind mux adapters before delete
i2c: designware: Replace MODULE_ALIAS() with MODULE_DEVICE_TABLE()
i2c: pxa: use 'time_left' variable with wait_event_timeout()
i2c: s3c2410: use 'time_left' variable with wait_event_timeout()
i2c: rk3x: use 'time_left' variable with wait_event_timeout()
i2c: qcom-geni: use 'time_left' variable with wait_for_completion_timeout()
i2c: jz4780: use 'time_left' variable with wait_for_completion_timeout()
i2c: synquacer: use 'time_left' variable with wait_for_completion_timeout()
i2c: stm32f7: use 'time_left' variable with wait_for_completion_timeout()
i2c: stm32f4: use 'time_left' variable with wait_for_completion_timeout()
i2c: st: use 'time_left' variable with wait_for_completion_timeout()
i2c: omap: use 'time_left' variable with wait_for_completion_timeout()
i2c: imx-lpi2c: use 'time_left' variable with wait_for_completion_timeout()
i2c: hix5hd2: use 'time_left' variable with wait_for_completion_timeout()
i2c: exynos5: use 'time_left' variable with wait_for_completion_timeout()
i2c: digicolor: use 'time_left' variable with wait_for_completion_timeout()
i2c: amd-mp2-plat: use 'time_left' variable with wait_for_completion_timeout()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"Core changes:
- Use DEFINE_SHOW_STORE_ATTRIBUTE() in debugfs entries
New drivers:
- Qualcomm PMIH0108, PMD8028, PMXR2230 and PM6450 pin control support
Improvements:
- Serious cleanup of the recently merged aw9523 driver
- Fix PIN_CONFIG_BIAS_DISABLE handling in pinctrl-single
- A slew of device tree binding cleanups
- Support a bus clock in the Samsung driver"
* tag 'pinctrl-v6.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (48 commits)
pinctrl: bcm2835: Make pin freeing behavior configurable
dt-bindings: pinctrl: qcom,pmic-gpio: Fix "comptaible" typo for PMIH0108
pinctrl: qcom: pinctrl-sm7150: Fix sdc1 and ufs special pins regs
dt-bindings: pinctrl: mediatek: mt7622: add "antsel" function
dt-bindings: pinctrl: mediatek: mt7622: fix array properties
pinctrl: samsung: drop redundant drvdata assignment
pinctrl: samsung: support a bus clock
dt-bindings: pinctrl: samsung: google,gs101-pinctrl needs a clock
pinctrl: renesas: rzg2l: Limit 2.5V power supply to Ethernet interfaces
pinctrl: renesas: r8a779h0: Add INTC-EX pins, groups, and function
pinctrl: renesas: r8a779h0: Fix IRQ suffixes
pinctrl: renesas: rzg2l: Remove extra space in function parameter
dt-bindings: pinctrl: qcom,pmic-mpp: add support for PM8901
pinctrl: pinconf-generic: print hex value
pinctrl: realtek: fix module autoloading
pinctrl: qcom: sm7150: fix module autoloading
pinctrl: loongson2: fix module autoloading
pinctrl: mediatek: fix module autoloading
pinctrl: freescale: imx8ulp: fix module autoloading
dt-bindings: pinctrl: qcom,pmic-gpio: Allow gpio-hog nodes
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
"Fix a bug in the new ecc P521 code as well as a buggy fix in qat"
* tag 'v6.10-p2' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: ecc - Prevent ecc_digits_from_bytes from reading too many bytes
crypto: qat - Fix ADF_DEV_RESET_SYNC memory leak
|
|
Add support for dynamic VLAN. VLAN group traffic is encapsulated and
encrypted in mac80211 and driver needs to set flags for the VLAN group
traffic to skip hardware encapsulation and encryption.
VLAN group traffic utilizes ext MSDU and HTT Metadata to set
encapsulation type to RAW and encryption type to OPEN in order to
inform firmware to skip hardware encapsulation and encryption.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Muna Sinada <[email protected]>
Acked-by: Jeff Johnson <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Link: https://msgid.link/[email protected]
|
|
If ath10k_snoc is built-in, while Qualcomm remoteprocs are built as
modules, compilation fails with:
/usr/bin/aarch64-linux-gnu-ld: drivers/net/wireless/ath/ath10k/snoc.o: in function `ath10k_modem_init':
drivers/net/wireless/ath/ath10k/snoc.c:1534: undefined reference to `qcom_register_ssr_notifier'
/usr/bin/aarch64-linux-gnu-ld: drivers/net/wireless/ath/ath10k/snoc.o: in function `ath10k_modem_deinit':
drivers/net/wireless/ath/ath10k/snoc.c:1551: undefined reference to `qcom_unregister_ssr_notifier'
Add corresponding dependency to ATH10K_SNOC Kconfig entry so that it's
built as module if QCOM_RPROC_COMMON is built as module too.
Fixes: 747ff7d3d742 ("ath10k: Don't always treat modem stop events as crashes")
Cc: [email protected]
Signed-off-by: Dmitry Baryshkov <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Link: https://msgid.link/[email protected]
|
|
Stephen reported that he was unable to get the dsa_loop driver to get
probed, and the reason ended up being because he had CONFIG_FIXED_PHY=y
in his kernel configuration. As Masahiro explained it:
"obj-m += dsa/" means everything under dsa/ must be modular.
If there is a built-in object under dsa/ with CONFIG_NET_DSA=m,
you cannot do "obj-$(CONFIG_NET_DSA) += dsa/".
You need to change it back to "obj-y += dsa/".
This was the case here whereby CONFIG_NET_DSA=m, and so the
obj-$(CONFIG_FIXED_PHY) += dsa_loop_bdinfo.o rule is not executed and
the DSA loop mdio_board info structure is not registered with the
kernel, and eventually the device is simply not found.
To preserve the intention of the original commit of limiting the amount
of folder descending, conditionally descend into drivers/net/dsa when
CONFIG_NET_DSA is enabled.
Fixes: 227d72063fcc ("dsa: simplify Kconfig symbols and dependencies")
Reported-by: Stephen Langstaff <[email protected]>
Signed-off-by: Florian Fainelli <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]>
Reviewed-by: Alexander Lobakin <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Remove unused 'agc_work' and 'vco_work' members of 'struct link'.
This follows commit d96324703ffa ("rt2x00: merge agc and vco works
with link tuner") where AGC and VCO calibration code was completely
redesigned. Compile tested only.
Signed-off-by: Dmitry Antipov <[email protected]>
Acked-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Link: https://msgid.link/[email protected]
|
|
PSR2_CTL[Block Count Number] is not used by LunarLake do not configure it.
Bspec: 69885
Signed-off-by: Jouni Högander <[email protected]>
Reviewed-by: Uma Shankar <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
On LunarLake PSR2_CTL[IO Wake Lines] contains now bit 13:18. Take this
into account when enabling PSR2_CTL.
Bspec: 69885
Signed-off-by: Jouni Högander <[email protected]>
Reviewed-by: Uma Shankar <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
On LunarLake maximum for IO and Fast Wake time line counts are 68: 6 bits +
5 lines added by the HW. Take this into account in calculation and when
writing the IO Wake lines.
v2: maximum line count is 68 (6 bits + 5 lines added by HW)
Signed-off-by: Jouni Högander <[email protected]>
Reviewed-by: Uma Shankar <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
The only generic interface to execute asynchronously in the BH context is
tasklet; however, it's marked deprecated and has some design flaws. To
replace tasklets, BH workqueue support was recently added. A BH workqueue
behaves similarly to regular workqueues except that the queued work items
are executed in the BH context.
Based on the work done by Tejun Heo <[email protected]>
Branch: https://git.kernel.org/pub/scm/linux/kernel/git/tj/wq.git for-6.10
Signed-off-by: Allen Pais <[email protected]>
Signed-off-by: Jassi Brar <[email protected]>
|
|
The return value of pm_runtime_get_sync() in cmdq_mbox_shutdown()
will return 1 when pm runtime state is active, and we don't want to
get the warning message in this case.
So we change the return value < 0 for WARN_ON().
Fixes: 8afe816b0c99 ("mailbox: mtk-cmdq-mailbox: Implement Runtime PM with autosuspend")
Signed-off-by: Jason-JH.Lin <[email protected]>
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
Signed-off-by: Jassi Brar <[email protected]>
|
|
Add MODULE_DEVICE_TABLE(), so this module could be properly autoloaded
based on the alias from of_device_id table.
Signed-off-by: Krzysztof Kozlowski <[email protected]>
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
Signed-off-by: Jassi Brar <[email protected]>
|
|
At least one IPI is used in TF-A for communication with PMC firmware.
If this IPI needs to be used by other agents such as RPU then, IPI
system interrupt can't be generated in mailbox driver. In such case
TF-A generates SGI to mailbox driver for IPI notification.
Signed-off-by: Tanmay Shah <[email protected]>
Signed-off-by: Saeed Nowshadi <[email protected]>
Signed-off-by: Jassi Brar <[email protected]>
|
|
Add support for ARM MHUv3 mailbox controller.
Support is limited to the MHUv3 Doorbell extension using only the PBX/MBX
combined interrupts.
Signed-off-by: Cristian Marussi <[email protected]>
Signed-off-by: Jassi Brar <[email protected]>
|