| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
As of commit de5c9bf40c45 ("net: phylink: require supported_interfaces to
be filled") Marvell 88e6350 switches fail to be probed:
...
mv88e6085 d0072004.mdio-mii:11: switch 0x3710 detected: Marvell 88E6350, revision 2
mv88e6085 d0072004.mdio-mii:11: phylink: error: empty supported_interfaces
error creating PHYLINK: -22
mv88e6085: probe of d0072004.mdio-mii:11 failed with error -22
...
The problem stems from the use of mv88e6185_phylink_get_caps() to get
the device capabilities. Create a new dedicated phylink_get_caps for the
6351 family (which the 6350 is one of) to properly support their set of
capabilities.
According to chip.h the 6351 switch family includes the 6171, 6175, 6350
and 6351 switches, so update each of these to use the correct
phylink_get_caps.
Fixes: de5c9bf40c45 ("net: phylink: require supported_interfaces to be filled")
Signed-off-by: Greg Ungerer <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / PHY / Thunderbolt fixes from Greg KH:
"Here are a number of reverts, fixes, and new device ids for 6.7-rc3
for the USB, PHY, and Thunderbolt driver subsystems. Include in here
are:
- reverts of some PHY drivers that went into 6.7-rc1 that shouldn't
have been merged yet, the author is reworking them based on review
comments as they were using older apis that shouldn't be used
anymore for newer drivers
- small thunderbolt driver fixes for reported issues
- USB driver fixes for a variety of small issues in dwc3, typec,
xhci, and other smaller drivers.
- new device ids for usb-serial and onboard_usb_hub drivers.
All of these have been in linux-next with no reported issues"
* tag 'usb-6.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (33 commits)
USB: serial: option: add Luat Air72*U series products
USB: dwc3: qcom: fix ACPI platform device leak
USB: dwc3: qcom: fix software node leak on probe errors
USB: dwc3: qcom: fix resource leaks on probe deferral
USB: dwc3: qcom: simplify wakeup interrupt setup
USB: dwc3: qcom: fix wakeup after probe deferral
dt-bindings: usb: qcom,dwc3: fix example wakeup interrupt types
usb: misc: onboard-hub: add support for Microchip USB5744
dt-bindings: usb: microchip,usb5744: Add second supply
usb: misc: ljca: Fix enumeration error on Dell Latitude 9420
USB: serial: option: add Fibocom L7xx modules
USB: xhci-plat: fix legacy PHY double init
usb: typec: tipd: Supply also I2C driver data
usb: xhci-mtk: fix in-ep's start-split check failure
usb: dwc3: set the dma max_seg_size
usb: config: fix iteration issue in 'usb_get_bos_descriptor()'
usb: dwc3: add missing of_node_put and platform_device_put
USB: dwc2: write HCINT with INTMASK applied
usb: misc: ljca: Drop _ADR support to get ljca children devices
usb: cdnsp: Fix deadlock issue during using NCM gadget
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
- A small cleanup patch for the Xen privcmd driver
- A fix for the swiotlb-xen driver which was missing the advertising of
the maximum mapping length
- A fix for Xen on Arm for a longstanding bug, which happened to occur
only recently: a structure in percpu memory crossed a page boundary,
which was rejected by the hypervisor
* tag 'for-linus-6.7a-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
arm/xen: fix xen_vcpu_info allocation alignment
xen: privcmd: Replace zero-length array with flex-array member and use __counted_by
swiotlb-xen: provide the "max_mapping_size" method
|
|
It is not always possible to keep a device in the runtime suspended state
when a system level suspend/resume cycle is executed. E.g. for ATA devices
connected to AHCI adapters, system resume resets the ATA ports, which
causes connected devices to spin up. In such case, a runtime suspended disk
will incorrectly be seen with a suspended runtime state because the device
is not resumed by sd_resume_system(). The power state seen by the user is
different than the actual device physical power state.
Fix this issue by introducing the struct scsi_device flag
force_runtime_start_on_system_start. When set, this flag causes
sd_resume_system() to request a runtime resume operation for runtime
suspended devices. This results in the user seeing the device runtime_state
as active after a system resume, thus correctly reflecting the device
physical power state.
Fixes: 9131bff6a9f1 ("scsi: core: pm: Only runtime resume if necessary")
Cc: <[email protected]>
Signed-off-by: Damien Le Moal <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
Commit 3cc2ffe5c16d ("scsi: sd: Differentiate system and runtime start/stop
management") changed the single bit manage_start_stop flag into 2 boolean
fields of the SCSI device structure. Commit 24eca2dce0f8 ("scsi: sd:
Introduce manage_shutdown device flag") introduced the manage_shutdown
boolean field for the same structure. Together, these 2 commits increase
the size of struct scsi_device by 8 bytes by using booleans instead of
defining the manage_xxx fields as single bit flags, similarly to other
flags of this structure.
Avoid this unnecessary structure size increase and be consistent with the
definition of other flags by reverting the definitions of the manage_xxx
fields as single bit flags.
Fixes: 3cc2ffe5c16d ("scsi: sd: Differentiate system and runtime start/stop management")
Fixes: 24eca2dce0f8 ("scsi: sd: Introduce manage_shutdown device flag")
Cc: <[email protected]>
Signed-off-by: Damien Le Moal <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Reviewed-by: Niklas Cassel <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
In MCQ mode, if cmd is pending in device and abort succeeds, response will
not be returned by device. So we need clear the cmd, otherwise timeout will
happen and next time we use same tag we will get a WARN_ON(lrbp->cmd).
Below is error log:
<3>[ 2277.447611][T21376] ufshcd-mtk 112b0000.ufshci: ufshcd_try_to_abort_task: cmd pending in the device. tag = 7
<3>[ 2277.476954][T21376] ufshcd-mtk 112b0000.ufshci: Aborting tag 7 / CDB 0x2a succeeded
<6>[ 2307.551263][T30974] ufshcd-mtk 112b0000.ufshci: ufshcd_abort: Device abort task at tag 7
<4>[ 2307.623264][ T327] WARNING: CPU: 5 PID: 327 at source/drivers/ufs/core/ufshcd.c:3021 ufshcd_queuecommand+0x66c/0xe34
Fixes: ab248643d3d6 ("scsi: ufs: core: Add error handling for MCQ mode")
Cc: <[email protected]>
Signed-off-by: Peter Wang <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Reviewed-by: Bart Van Assche <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
Some panel devices already depend on DRM device, like the panel in
arch/arm/boot/dts/st/ste-ux500-samsung-skomer.dts, because DRM device is
the ancestor of those panel devices. device_link_add() would fail by
returning a NULL pointer for those panel devices because of the existing
dependency. So, check the dependency by calling device_is_dependent()
before adding or deleting device link between panel device and DRM device
so that the link is managed only for independent panel devices.
Fixes: 887878014534 ("drm/bridge: panel: Fix device link for DRM_BRIDGE_ATTACH_NO_CONNECTOR")
Fixes: 199cf07ebd2b ("drm/bridge: panel: Add a device link between drm device and panel device")
Reported-by: Linus Walleij <[email protected]>
Closes: https://lore.kernel.org/lkml/CACRpkdaGzXD6HbiX7mVUNJAJtMEPG00Pp6+nJ1P0JrfJ-ArMvQ@mail.gmail.com/T/
Tested-by: Linus Walleij <[email protected]>
Signed-off-by: Liu Ying <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These add an ACPI IRQ override quirk for ASUS ExpertBook B1402CVA and
fix an ACPI processor idle issue leading to triple-faults in Xen HVM
guests and an ACPI backlight driver issue that causes GPUs to
misbehave while their children power is being fixed up.
Specifics:
- Avoid powering up GPUs while attempting to fix up power for their
children (Hans de Goede)
- Use raw_safe_halt() instead of safe_halt() in acpi_idle_play_dead()
so as to avoid triple-falts during CPU online in Xen HVM guests due
to the setting of the hardirqs_enabled flag in safe_halt() (David
Woodhouse)
- Add an ACPI IRQ override quirk for ASUS ExpertBook B1402CVA (Hans
de Goede)"
* tag 'acpi-6.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: resource: Skip IRQ override on ASUS ExpertBook B1402CVA
ACPI: video: Use acpi_device_fix_up_power_children()
ACPI: PM: Add acpi_device_fix_up_power_children() function
ACPI: processor_idle: use raw_safe_halt() in acpi_idle_play_dead()
|
|
Merge ACPI backlight driver fixes and an ACPI processor driver fix for
6.7-rc3:
- Avoid powering up GPUs while attempting to fix up power for their
children (Hans de Goede).
- Use raw_safe_halt() instead of safe_halt() in acpi_idle_play_dead()
so as to avoid triple-falts during CPU online in Xen HVM guests due
to the setting of the hardirqs_enabled flag in safe_halt() (David
Woodhouse).
* acpi-video:
ACPI: video: Use acpi_device_fix_up_power_children()
ACPI: PM: Add acpi_device_fix_up_power_children() function
* acpi-processor:
ACPI: processor_idle: use raw_safe_halt() in acpi_idle_play_dead()
|
|
Pull drm fixes from Dave Airlie:
"Back to regular scheduled fixes pull request, mainly a bunch of msm,
some i915 and otherwise a few scattered, one memory crasher in the
nouveau GSP paths is helping stabilise that work.
msm:
- Fix the VREG_CTRL_1 for 4nm CPHY to match downstream
- Remove duplicate call to drm_kms_helper_poll_init() in
msm_drm_init()
- Fix the safe_lut_tbl[] for sc8280xp to match downstream
- Don't attach the drm_dp_set_subconnector_property() for eDP
- Fix to attach drm_dp_set_subconnector_property() for DP. Otherwise
there is a bootup crash on multiple targets
- Remove unnecessary NULL check left behind during cleanup
i915:
- Fix race between DP MST connectore registration and setup
- Fix GT memory leak on probe error path
panel:
- Fixes for innolux and auo,b101uan08.3 panel.
- Fix Himax83102-j02 timings.
ivpu:
- Fix ivpu MMIO reset.
ast:
- AST fix on connetor disconnection.
nouveau:
- gsp memory corruption fix
rockchip:
- color fix"
* tag 'drm-fixes-2023-11-24' of git://anongit.freedesktop.org/drm/drm:
nouveau/gsp: allocate enough space for all channel ids.
drm/panel: boe-tv101wum-nl6: Fine tune Himax83102-j02 panel HFP and HBP
drm/ast: Disconnect BMC if physical connector is connected
accel/ivpu/37xx: Fix hangs related to MMIO reset
drm/rockchip: vop: Fix color for RGB888/BGR888 format on VOP full
drm/i915: do not clean GT table on error path
drm/i915/dp_mst: Fix race between connector registration and setup
drm/panel: simple: Fix Innolux G101ICE-L01 timings
drm/panel: simple: Fix Innolux G101ICE-L01 bus flags
drm/msm: remove unnecessary NULL check
drm/panel: auo,b101uan08.3: Fine tune the panel power sequence
drm/msm/dp: attach the DP subconnector property
drm/msm/dp: don't touch DP subconnector property in eDP case
drm/msm/dpu: Add missing safe_lut_tbl in sc8280xp catalog
drm/msm: remove exra drm_kms_helper_poll_init() call
drm/msm/dsi: use the correct VREG_CTRL_1 value for 4nm cphy
|
|
This error path should return -EINVAL instead of success.
Fixes: 57974a55d995 ("wifi: iwlwifi: mvm: refactor iwl_mvm_mac_sta_state_common()")
Signed-off-by: Dan Carpenter <[email protected]>
Acked-by: Gregory Greenman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Johannes Berg <[email protected]>
|
|
Commit 028ddcac477b ("bcache: Remove unnecessary NULL point check in
node allocations") replaced IS_ERR_OR_NULL by IS_ERR. This leads to a
NULL pointer dereference.
BUG: kernel NULL pointer dereference, address: 0000000000000080
Call Trace:
? __die_body.cold+0x1a/0x1f
? page_fault_oops+0xd2/0x2b0
? exc_page_fault+0x70/0x170
? asm_exc_page_fault+0x22/0x30
? btree_node_free+0xf/0x160 [bcache]
? up_write+0x32/0x60
btree_gc_coalesce+0x2aa/0x890 [bcache]
? bch_extent_bad+0x70/0x170 [bcache]
btree_gc_recurse+0x130/0x390 [bcache]
? btree_gc_mark_node+0x72/0x230 [bcache]
bch_btree_gc+0x5da/0x600 [bcache]
? cpuusage_read+0x10/0x10
? bch_btree_gc+0x600/0x600 [bcache]
bch_gc_thread+0x135/0x180 [bcache]
The relevant code starts with:
new_nodes[0] = NULL;
for (i = 0; i < nodes; i++) {
if (__bch_keylist_realloc(&keylist, bkey_u64s(&r[i].b->key)))
goto out_nocoalesce;
// ...
out_nocoalesce:
// ...
for (i = 0; i < nodes; i++)
if (!IS_ERR(new_nodes[i])) { // IS_ERR_OR_NULL before
028ddcac477b
btree_node_free(new_nodes[i]); // new_nodes[0] is NULL
rw_unlock(true, new_nodes[i]);
}
This patch replaces IS_ERR() by IS_ERR_OR_NULL() to fix this.
Fixes: 028ddcac477b ("bcache: Remove unnecessary NULL point check in node allocations")
Link: https://lore.kernel.org/all/[email protected]/
Cc: [email protected]
Cc: Zheng Wang <[email protected]>
Cc: Coly Li <[email protected]>
Signed-off-by: Markus Weippert <[email protected]>
Signed-off-by: Jens Axboe <[email protected]>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 6.7-rc3
Here are a couple of modem device entry fixes and some new modem device
ids.
All have been in linux-next with no reported issues.
* tag 'usb-serial-6.7-rc3' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial: (329 commits)
USB: serial: option: add Luat Air72*U series products
USB: serial: option: add Fibocom L7xx modules
USB: serial: option: fix FM101R-GL defines
USB: serial: option: don't claim interface 4 for ZTE MF290
Linux 6.7-rc2
prctl: Disable prctl(PR_SET_MDWE) on parisc
parisc/power: Fix power soft-off when running on qemu
parisc: Replace strlcpy() with strscpy()
NFSD: Fix checksum mismatches in the duplicate reply cache
NFSD: Fix "start of NFS reply" pointer passed to nfsd_cache_update()
NFSD: Update nfsd_cache_append() to use xdr_stream
nfsd: fix file memleak on client_opens_release
dm-crypt: start allocating with MAX_ORDER
dm-verity: don't use blocking calls from tasklets
dm-bufio: fix no-sleep mode
dm-delay: avoid duplicate logic
dm-delay: fix bugs introduced by kthread mode
dm-delay: fix a race between delay_presuspend and delay_bio
drm/amdgpu/gmc9: disable AGP aperture
drm/amdgpu/gmc10: disable AGP aperture
...
|
|
The pin descriptor should be returned if the name has been found in the
descriptor table. Remove the negation in the if statement for accurate
retrieval.
Fixes: e99ce78030db ("pinctrl: realtek: Add common pinctrl driver for Realtek DHC RTD SoCs")
Signed-off-by: Tzuyi Chang <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Linus Walleij <[email protected]>
|
|
Control flow integrity is now checking that type signatures match on
indirect function calls. That breaks closures, which embed a work_struct
in a closure in such a way that a closure_fn may also be used as a
workqueue fn by the underlying closure code.
So we have to change closure fns to take a work_struct as their
argument - but that results in a loss of clarity, as closure fns have
different semantics from normal workqueue functions (they run owning a
ref on the closure, which must be released with continue_at() or
closure_return()).
Thus, this patc introduces CLOSURE_CALLBACK() and closure_type() macros
as suggested by Kees, to smooth things over a bit.
Suggested-by: Kees Cook <[email protected]>
Cc: Coly Li <[email protected]>
Signed-off-by: Kent Overstreet <[email protected]>
|
|
Before returning the rswitch_start_xmit() in the error path,
dev_kfree_skb_any() should be called. So, fix it.
Fixes: 33f5d733b589 ("net: renesas: rswitch: Improve TX timestamp accuracy")
Signed-off-by: Yoshihiro Shimoda <[email protected]>
Reviewed-by: Wojciech Drewek <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This .ndo_start_xmit() function should return netdev_tx_t value,
not -ENOMEM. So, fix it.
Fixes: 33f5d733b589 ("net: renesas: rswitch: Improve TX timestamp accuracy")
Signed-off-by: Yoshihiro Shimoda <[email protected]>
Reviewed-by: Wojciech Drewek <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The type of ret in rswitch_start_xmit() should be netdev_tx_t. So,
fix it.
Fixes: 3590918b5d07 ("net: ethernet: renesas: Add support for "Ethernet Switch"")
Signed-off-by: Yoshihiro Shimoda <[email protected]>
Reviewed-by: Wojciech Drewek <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata
Pull ata fix from Damien Le Moal:
- Add a missing error check in the adapter initialization of the
pata_isapnp driver (Chen)
* tag 'ata-6.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata:
ata: pata_isapnp: Add missing error check for devm_ioport_map()
|
|
Pull block fixes from Jens Axboe:
"A bit bigger than usual at this time, but nothing really earth
shattering:
- NVMe pull request via Keith:
- TCP TLS fixes (Hannes)
- Authentifaction fixes (Mark, Hannes)
- Properly terminate target names (Christoph)
- MD pull request via Song, fixing a raid5 corruption issue
- Disentanglement of the dependency mess in nvme introduced with the
tls additions. Now it should actually build on all configs (Arnd)
- Series of bcache fixes (Coly)
- Removal of a dead helper (Damien)
- s390 dasd fix (Muhammad, Jan)
- lockdep blk-cgroup fixes (Ming)"
* tag 'block-6.7-2023-11-23' of git://git.kernel.dk/linux: (33 commits)
nvme: tcp: fix compile-time checks for TLS mode
nvme: target: fix Kconfig select statements
nvme: target: fix nvme_keyring_id() references
nvme: move nvme_stop_keep_alive() back to original position
nbd: pass nbd_sock to nbd_read_reply() instead of index
s390/dasd: protect device queue against concurrent access
s390/dasd: resolve spelling mistake
block/null_blk: Fix double blk_mq_start_request() warning
nvmet-tcp: always initialize tls_handshake_tmo_work
nvmet: nul-terminate the NQNs passed in the connect command
nvme: blank out authentication fabrics options if not configured
nvme: catch errors from nvme_configure_metadata()
nvme-tcp: only evaluate 'tls' option if TLS is selected
nvme-auth: set explanation code for failure2 msgs
nvme-auth: unlock mutex in one place only
block: Remove blk_set_runtime_active()
nbd: fix null-ptr-dereference while accessing 'nbd->config'
nbd: factor out a helper to get nbd_config without holding 'config_lock'
nbd: fold nbd config initialization into nbd_alloc_config()
bcache: avoid NULL checking to c->root in run_cache_set()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid
Pull HID fixes from Jiri Kosina:
- revert of commit that caused regression to many Logitech unifying
receiver users (Jiri Kosina)
- power management fix for hid-mcp2221 (Hamish Martin)
- fix for race condition between HID core and HID debug (Charles Yi)
- a couple of assorted device-ID-specific quirks
* tag 'for-linus-2023112301' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
HID: multitouch: Add quirk for HONOR GLO-GXXX touchpad
HID: hid-asus: reset the backlight brightness level on resume
HID: hid-asus: add const to read-only outgoing usb buffer
Revert "HID: logitech-dj: Add support for a new lightspeed receiver iteration"
HID: add ALWAYS_POLL quirk for Apple kb
HID: glorious: fix Glorious Model I HID report
HID: fix HID device resource race between HID core and debugging support
HID: apple: add Jamesdonkey and A3R to non-apple keyboards list
HID: mcp2221: Allow IO to start during probe
HID: mcp2221: Set driver data before I2C adapter add
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
drm/i915 fixes for v6.7-rc3:
- Fix race between DP MST connectore registration and setup
- Fix GT memory leak on probe error path
Signed-off-by: Dave Airlie <[email protected]>
From: Jani Nikula <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
Fixes for v6.7-rc3:
- Panel fixes for innolux and auo,b101uan08.3 panel.
- Fix ivpu MMIO reset.
- AST fix on connetor disconnection.
- nouveau gsp fix.
- rockchip color fix.
- Fix Himax83102-j02 timings.
Signed-off-by: Dave Airlie <[email protected]>
From: Maarten Lankhorst <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
https://gitlab.freedesktop.org/drm/msm into drm-fixes
Fixes for v6.7-rc3:
- Fix the VREG_CTRL_1 for 4nm CPHY to match downstream
- Remove duplicate call to drm_kms_helper_poll_init() in msm_drm_init()
- Fix the safe_lut_tbl[] for sc8280xp to match downstream
- Don't attach the drm_dp_set_subconnector_property() for eDP
- Fix to attach drm_dp_set_subconnector_property() for DP. Otherwise
there is a bootup crash on multiple targets
- Remove unnecessary NULL check left behind during cleanup
Signed-off-by: Dave Airlie <[email protected]>
From: Rob Clark <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGtkna3P3mvaF53n2ARJACaXQU+OFfShayTrsUVmqCOmNQ@mail.gmail.com
|
|
Commit 2b3486bc2d23 ("bpf: Introduce device-bound XDP programs") introduced
device-bound programs by largely reusing existing offloading infrastructure.
This changed the semantics of 'prog->aux->offload' a bit. Now, it's non-NULL
for both offloaded and device-bound programs.
Instead of looking at 'prog->aux->offload' let's call bpf_prog_is_offloaded
which should be true iff the program is offloaded and not merely device-bound.
Fixes: 2b3486bc2d23 ("bpf: Introduce device-bound XDP programs")
Reported-by: [email protected]
Signed-off-by: Stanislav Fomichev <[email protected]>
Signed-off-by: Daniel Borkmann <[email protected]>
Reviewed-by: Jakub Kicinski <[email protected]>
Cc: Dipendra Khadka <[email protected]>
Link: https://lore.kernel.org/bpf/[email protected]
Signed-off-by: Alexei Starovoitov <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from bpf.
Current release - regressions:
- Revert "net: r8169: Disable multicast filter for RTL8168H and
RTL8107E"
- kselftest: rtnetlink: fix ip route command typo
Current release - new code bugs:
- s390/ism: make sure ism driver implies smc protocol in kconfig
- two build fixes for tools/net
Previous releases - regressions:
- rxrpc: couple of ACK/PING/RTT handling fixes
Previous releases - always broken:
- bpf: verify bpf_loop() callbacks as if they are called unknown
number of times
- improve stability of auto-bonding with Hyper-V
- account BPF-neigh-redirected traffic in interface statistics
Misc:
- net: fill in some more MODULE_DESCRIPTION()s"
* tag 'net-6.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (58 commits)
tools: ynl: fix duplicate op name in devlink
tools: ynl: fix header path for nfsd
net: ipa: fix one GSI register field width
tls: fix NULL deref on tls_sw_splice_eof() with empty record
net: axienet: Fix check for partial TX checksum
vsock/test: fix SEQPACKET message bounds test
i40e: Fix adding unsupported cloud filters
ice: restore timestamp configuration after device reset
ice: unify logic for programming PFINT_TSYN_MSK
ice: remove ptp_tx ring parameter flag
amd-xgbe: propagate the correct speed and duplex status
amd-xgbe: handle the corner-case during tx completion
amd-xgbe: handle corner-case during sfp hotplug
net: veth: fix ethtool stats reporting
octeontx2-pf: Fix ntuple rule creation to direct packet to VF with higher Rx queue than its PF
net: usb: qmi_wwan: claim interface 4 for ZTE MF290
Revert "net: r8169: Disable multicast filter for RTL8168H and RTL8107E"
net/smc: avoid data corruption caused by decline
nfc: virtual_ncidev: Add variable to check if ndev is running
dpll: Fix potential msg memleak when genlmsg_put_reply failed
...
|
|
Update the USB serial option driver support for Luat Air72*U series
products.
ID 1782:4e00 Spreadtrum Communications Inc. UNISOC-8910
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 13 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1782 ProdID=4e00 Rev=00.00
S: Manufacturer=UNISOC
S: Product=UNISOC-8910
C: #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=400mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=e0(wlcon) Sub=01 Prot=03 Driver=rndis_host
E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=4096ms
I: If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=rndis_host
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
If#= 2: AT
If#= 3: PPP + AT
If#= 4: Debug
Co-developed-by: Yangyu Chen <[email protected]>
Signed-off-by: Yangyu Chen <[email protected]>
Signed-off-by: Asuna Yang <[email protected]>
Cc: [email protected]
Signed-off-by: Johan Hovold <[email protected]>
|
|
With cat regulator_summary, we found that vqmmc was not shutting
down after the card was pulled.
cat /sys/kernel/debug/regulator/regulator_summary
1.before fix
1)Insert SD card
vddsdio 1 1 0 unknown 3500mV 0mA 1200mV 3750mV
71100000.mmc-vqmmc 1 0mA 3500mV 3600mV
2)Pull out the SD card
vddsdio 1 1 0 unknown 3500mV 0mA 1200mV 3750mV
71100000.mmc-vqmmc 1 0mA 3500mV 3600mV
2.after fix
1)Insert SD cardt
vddsdio 1 1 0 unknown 3500mV 0mA 1200mV 3750mV
71100000.mmc-vqmmc 1 0mA 3500mV 3600mV
2)Pull out the SD card
vddsdio 0 1 0 unknown 3500mV 0mA 1200mV 3750mV
71100000.mmc-vqmmc 0 0mA 3500mV 3600mV
Fixes: fb8bd90f83c4 ("mmc: sdhci-sprd: Add Spreadtrum's initial host controller")
Signed-off-by: Wenchao Chen <[email protected]>
Cc: [email protected]
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Ulf Hansson <[email protected]>
|
|
To address IO performance commit f9e5b33934ce
("mmc: host: Improve I/O read/write performance for GL9763E")
limited LPM negotiation to runtime suspend state.
The problem is that it only flips the switch in the runtime PM
resume/suspend logic.
Disable LPM negotiation in gl9763e_add_host.
This helps in two ways:
1. It was found that the LPM switch stays in the same position after
warm reboot. Having it set in init helps with consistency.
2. Disabling LPM during the first runtime resume leaves us susceptible
to the performance issue in the time window between boot and the
first runtime suspend.
Fixes: f9e5b33934ce ("mmc: host: Improve I/O read/write performance for GL9763E")
Cc: [email protected]
Signed-off-by: Kornel Dulęba <[email protected]>
Reviewed-by: Sven van Ashbrook <[email protected]>
Acked-by: Adrian Hunter <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Ulf Hansson <[email protected]>
|
|
The width of the R_LENGTH field of the EV_CH_E_CNTXT_1 GSI register
is 24 bits (not 20 bits) starting with IPA v5.0. Fix this.
Fixes: faf0678ec8a0 ("net: ipa: add IPA v5.0 GSI register definitions")
Signed-off-by: Alex Elder <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Due to a typo, the code checked the RX checksum feature in the TX path.
Fixes: 8a3b7a252dca ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Samuel Holland <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Reviewed-by: Radhey Shyam Pandey <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
If a VF tries to add unsupported cloud filter through virtchnl
then i40e_add_del_cloud_filter(_big_buf) returns -ENOTSUPP but
this error code is stored in 'ret' instead of 'aq_ret' that
is used as error code sent back to VF. In this scenario where
one of the mentioned functions fails the value of 'aq_ret'
is zero so the VF will incorrectly receive a 'success'.
Use 'aq_ret' to store return value and remove 'ret' local
variable. Additionally fix the issue when filter allocation
fails, in this case no notification is sent back to the VF.
Fixes: e284fc280473 ("i40e: Add and delete cloud filter")
Reviewed-by: Simon Horman <[email protected]>
Signed-off-by: Ivan Vecera <[email protected]>
Tested-by: Rafal Romanowski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
The driver calls ice_ptp_cfg_timestamp() during ice_ptp_prepare_for_reset()
to disable timestamping while the device is resetting. This operation
destroys the user requested configuration. While the driver does call
ice_ptp_cfg_timestamp in ice_rebuild() to restore some hardware settings
after a reset, it unconditionally passes true or false, resulting in
failure to restore previous user space configuration.
This results in a device reset forcibly disabling timestamp configuration
regardless of current user settings.
This was not detected previously due to a quirk of the LinuxPTP ptp4l
application. If ptp4l detects a missing timestamp, it enters a fault state
and performs recovery logic which includes executing SIOCSHWTSTAMP again,
restoring the now accidentally cleared configuration.
Not every application does this, and for these applications, timestamps
will mysteriously stop after a PF reset, without being restored until an
application restart.
Fix this by replacing ice_ptp_cfg_timestamp() with two new functions:
1) ice_ptp_disable_timestamp_mode() which unconditionally disables the
timestamping logic in ice_ptp_prepare_for_reset() and ice_ptp_release()
2) ice_ptp_restore_timestamp_mode() which calls
ice_ptp_restore_tx_interrupt() to restore Tx timestamping configuration,
calls ice_set_rx_tstamp() to restore Rx timestamping configuration, and
issues an immediate TSYN_TX interrupt to ensure that timestamps which
may have occurred during the device reset get processed.
Modify the ice_ptp_set_timestamp_mode to directly save the user
configuration and then call ice_ptp_restore_timestamp_mode. This way, reset
no longer destroys the saved user configuration.
This obsoletes the ice_set_tx_tstamp() function which can now be safely
removed.
With this change, all devices should now restore Tx and Rx timestamping
functionality correctly after a PF reset without application intervention.
Fixes: 77a781155a65 ("ice: enable receive hardware timestamping")
Fixes: ea9b847cda64 ("ice: enable transmit timestamps for E810 devices")
Signed-off-by: Jacob Keller <[email protected]>
Reviewed-by: Jesse Brandeburg <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Tested-by: Pucha Himasekhar Reddy <[email protected]> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <[email protected]>
Signed-off-by: Paolo Abeni <[email protected]>
|
|
Commit d938a8cca88a ("ice: Auxbus devices & driver for E822 TS") modified
how Tx timestamps are handled for E822 devices. On these devices, only the
clock owner handles reading the Tx timestamp data from firmware. To do
this, the PFINT_TSYN_MSK register is modified from the default value to one
which enables reacting to a Tx timestamp on all PHY ports.
The driver currently programs PFINT_TSYN_MSK in different places depending
on whether the port is the clock owner or not. For the clock owner, the
PFINT_TSYN_MSK value is programmed during ice_ptp_init_owner just before
calling ice_ptp_tx_ena_intr to program the PHY ports.
For the non-clock owner ports, the PFINT_TSYN_MSK is programmed during
ice_ptp_init_port.
If a large enough device reset occurs, the PFINT_TSYN_MSK register will be
reset to the default value in which only the PHY associated directly with
the PF will cause the Tx timestamp interrupt to trigger.
The driver lacks logic to reprogram the PFINT_TSYN_MSK register after a
device reset. For the E822 device, this results in the PF no longer
responding to interrupts for other ports. This results in failure to
deliver Tx timestamps to user space applications.
Rename ice_ptp_configure_tx_tstamp to ice_ptp_cfg_tx_interrupt, and unify
the logic for programming PFINT_TSYN_MSK and PFINT_OICR_ENA into one place.
This function will program both registers according to the combination of
user configuration and device requirements.
This ensures that PFINT_TSYN_MSK is always restored when we configure the
Tx timestamp interrupt.
Fixes: d938a8cca88a ("ice: Auxbus devices & driver for E822 TS")
Signed-off-by: Jacob Keller <[email protected]>
Reviewed-by: Jesse Brandeburg <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Tested-by: Pucha Himasekhar Reddy <[email protected]> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <[email protected]>
Signed-off-by: Paolo Abeni <[email protected]>
|
|
Before performing a Tx timestamp in ice_stamp(), the driver checks a ptp_tx
ring variable to see if timestamping is enabled on that ring. This value is
set for all rings whenever userspace configures Tx timestamping.
Ostensibly this was done to avoid wasting cycles checking other fields when
timestamping has not been enabled. However, for Tx timestamps we already
get an individual per-SKB flag indicating whether userspace wants to
request a timestamp on that packet. We do not gain much by also having
a separate flag to check for whether timestamping was enabled.
In fact, the driver currently fails to restore the field after a PF reset.
Because of this, if a PF reset occurs, timestamps will be disabled.
Since this flag doesn't add value in the hotpath, remove it and always
provide a timestamp if the SKB flag has been set.
A following change will fix the reset path to properly restore user
timestamping configuration completely.
This went unnoticed for some time because one of the most common
applications using Tx timestamps, ptp4l, will reconfigure the socket as
part of its fault recovery logic.
Fixes: ea9b847cda64 ("ice: enable transmit timestamps for E810 devices")
Signed-off-by: Jacob Keller <[email protected]>
Reviewed-by: Jesse Brandeburg <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Tested-by: Pucha Himasekhar Reddy <[email protected]> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <[email protected]>
Signed-off-by: Paolo Abeni <[email protected]>
|
|
xgbe_get_link_ksettings() does not propagate correct speed and duplex
information to ethtool during cable unplug. Due to which ethtool reports
incorrect values for speed and duplex.
Address this by propagating correct information.
Fixes: 7c12aa08779c ("amd-xgbe: Move the PHY support into amd-xgbe")
Acked-by: Shyam Sundar S K <[email protected]>
Signed-off-by: Raju Rangoju <[email protected]>
Reviewed-by: Wojciech Drewek <[email protected]>
Signed-off-by: Paolo Abeni <[email protected]>
|
|
The existing implementation uses software logic to accumulate tx
completions until the specified time (1ms) is met and then poll them.
However, there exists a tiny gap which leads to a race between
resetting and checking the tx_activate flag. Due to this the tx
completions are not reported to upper layer and tx queue timeout
kicks-in restarting the device.
To address this, introduce a tx cleanup mechanism as part of the
periodic maintenance process.
Fixes: c5aa9e3b8156 ("amd-xgbe: Initial AMD 10GbE platform driver")
Acked-by: Shyam Sundar S K <[email protected]>
Signed-off-by: Raju Rangoju <[email protected]>
Reviewed-by: Wojciech Drewek <[email protected]>
Signed-off-by: Paolo Abeni <[email protected]>
|
|
Force the mode change for SFI in Fixed PHY configurations. Fixed PHY
configurations needs PLL to be enabled while doing mode set. When the
SFP module isn't connected during boot, driver assumes AN is ON and
attempts auto-negotiation. However, if the connected SFP comes up in
Fixed PHY configuration the link will not come up as PLL isn't enabled
while the initial mode set command is issued. So, force the mode change
for SFI in Fixed PHY configuration to fix link issues.
Fixes: e57f7a3feaef ("amd-xgbe: Prepare for working with more than one type of phy")
Acked-by: Shyam Sundar S K <[email protected]>
Signed-off-by: Raju Rangoju <[email protected]>
Reviewed-by: Wojciech Drewek <[email protected]>
Signed-off-by: Paolo Abeni <[email protected]>
|
|
Fix a possible misalignment between page_pool stats and tx xdp_stats
reported in veth_get_ethtool_stats routine.
The issue can be reproduced configuring the veth pair with the
following tx/rx queues:
$ip link add v0 numtxqueues 2 numrxqueues 4 type veth peer name v1 \
numtxqueues 1 numrxqueues 1
and loading a simple XDP program on v0 that just returns XDP_PASS.
In this case on v0 the page_pool stats overwrites tx xdp_stats for queue 1.
Fix the issue incrementing pp_idx of dev->real_num_tx_queues * VETH_TQ_STATS_LEN
since we always report xdp_stats for all tx queues in ethtool.
Fixes: 4fc418053ec7 ("net: veth: add page_pool stats")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Link: https://lore.kernel.org/r/c5b5d0485016836448453f12846c7c4ab75b094a.1700593593.git.lorenzo@kernel.org
Signed-off-by: Paolo Abeni <[email protected]>
|
|
queue than its PF
It is possible to add a ntuple rule which would like to direct packet to
a VF whose number of queues are greater/less than its PF's queue numbers.
For example a PF can have 2 Rx queues but a VF created on that PF can have
8 Rx queues. As of today, ntuple rule will reject rule because it is
checking the requested queue number against PF's number of Rx queues.
As a part of this fix if the action of a ntuple rule is to move a packet
to a VF's queue then the check is removed. Also, a debug information is
printed to aware user that it is user's responsibility to cross check if
the requested queue number on that VF is a valid one.
Fixes: f0a1913f8a6f ("octeontx2-pf: Add support for ethtool ntuple filters")
Signed-off-by: Suman Ghosh <[email protected]>
Reviewed-by: Wojciech Drewek <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Paolo Abeni <[email protected]>
|
|
Interface 4 is used by for QMI interface in stock firmware of MF28D, the
router which uses MF290 modem. Rebind it to qmi_wwan after freeing it up
from option driver.
The proper configuration is:
Interface mapping is:
0: QCDM, 1: (unknown), 2: AT (PCUI), 2: AT (Modem), 4: QMI
T: Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 4 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=19d2 ProdID=0189 Rev= 0.00
S: Manufacturer=ZTE, Incorporated
S: Product=ZTE LTE Technologies MSM
C:* #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=84(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E: Ad=86(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
Cc: Bjørn Mork <[email protected]>
Signed-off-by: Lech Perczak <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Paolo Abeni <[email protected]>
|
|
Set GENPD_FLAG_ACTIVE_WAKEUP for all RPM power domains so that power
domains necessary for wakeup/"awake path" devices are kept on across
suspend.
This is needed for example for the *_AO ("active-only") variants of the
RPMPDs used by the CPU. Those should maintain their votes also across
system suspend to ensure the CPU can keep running for the whole suspend
process (ending in a firmware call). When the RPM firmware detects that
the CPUs are in a deep idle state it will drop those votes automatically.
Signed-off-by: Stephan Gerhold <[email protected]>
Reviewed-by: Ulf Hansson <[email protected]>
Signed-off-by: Viresh Kumar <[email protected]>
|
|
>From the Linux point of view, the power domains used by the CPU must
stay always-on. This is because we still need the CPU to keep running
until the last instruction, which will typically be a firmware call that
shuts down the CPU cleanly.
At the moment the power domain votes (enable + performance state) are
dropped during system suspend, which means the CPU could potentially
malfunction while entering suspend.
We need to distinguish between two different setups used with
qcom-cpufreq-nvmem:
1. CPR power domain: The backing regulator used by CPR should stay
always-on in Linux; it is typically disabled automatically by
hardware when the CPU enters a deep idle state. However, we
should pause the CPR state machine during system suspend.
2. RPMPD: The power domains used by the CPU should stay always-on
in Linux (also across system suspend). The CPU typically only
uses the *_AO ("active-only") variants of the power domains in
RPMPD. For those, the RPM firmware will automatically drop
the votes internally when the CPU enters a deep idle state.
Make this work correctly by calling device_set_awake_path() on the
virtual genpd devices, so that the votes are maintained across system
suspend. The power domain drivers need to set GENPD_FLAG_ACTIVE_WAKEUP
to opt into staying on during system suspend.
For now we only set this for the RPMPD case. For CPR, not setting it
will ensure the state machine is still paused during system suspend,
while the backing regulator will stay on with "regulator-always-on".
Signed-off-by: Stephan Gerhold <[email protected]>
Reviewed-by: Ulf Hansson <[email protected]>
Signed-off-by: Viresh Kumar <[email protected]>
|
|
The genpd core caches performance state votes from devices that are
runtime suspended as of commit 3c5a272202c2 ("PM: domains: Improve
runtime PM performance state handling"). They get applied once the
device becomes active again.
To attach the power domains needed by qcom-cpufreq-nvmem the OPP core
calls genpd_dev_pm_attach_by_id(). This results in "virtual" dummy
devices that use runtime PM only to control the enable and performance
state for the attached power domain.
However, at the moment nothing ever resumes the virtual devices created
for qcom-cpufreq-nvmem. They remain permanently runtime suspended. This
means that performance state votes made during cpufreq scaling get
always cached and never applied to the hardware.
Fix this by enabling the devices after attaching them.
Without this fix performance states votes are silently ignored, and the
CPU/CPR voltage is never adjusted. This has been broken since 5.14 but
for some reason no one noticed this on QCS404 so far.
Fixes: 1cb8339ca225 ("cpufreq: qcom: Add support for qcs404 on nvmem driver")
Signed-off-by: Stephan Gerhold <[email protected]>
Reviewed-by: Ulf Hansson <[email protected]>
Signed-off-by: Viresh Kumar <[email protected]>
|
|
For a 900MHz i.MX6ULL CPU the 792MHz OPP is disabled. There is no
convincing reason to disable this OPP. If a CPU can run at 900MHz,
it should also be able to cope with 792MHz. Looking at the voltage
level of 792MHz in [1] (page 24, table 10. "Operating Ranges") the
current defined OPP is above the minimum. So the voltage level
shouldn't be a problem. However in [2] (page 24, table 10.
"Operating Ranges"), it is not mentioned that 792MHz OPP isn't
allowed. Change it to only disable 792MHz OPP for i.MX6ULL types
below 792 MHz.
[1] https://www.nxp.com/docs/en/data-sheet/IMX6ULLIEC.pdf
[2] https://www.nxp.com/docs/en/data-sheet/IMX6ULLCEC.pdf
Fixes: 0aa9abd4c212 ("cpufreq: imx6q: check speed grades for i.MX6ULL")
Signed-off-by: Christoph Niedermaier <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
[ Viresh: Edited subject ]
Signed-off-by: Viresh Kumar <[email protected]>
|
|
When CONFIG_NVME_KEYRING is enabled as a loadable module, but the TCP
host code is built-in, it fails to link:
arm-linux-gnueabi-ld: drivers/nvme/host/tcp.o: in function `nvme_tcp_setup_ctrl':
tcp.c:(.text+0x1940): undefined reference to `nvme_tls_psk_default'
The problem is that the compile-time conditionals are inconsistent here,
using a mix of #ifdef CONFIG_NVME_TCP_TLS, IS_ENABLED(CONFIG_NVME_TCP_TLS)
and IS_ENABLED(CONFIG_NVME_KEYRING) checks, with CONFIG_NVME_KEYRING
controlling whether the implementation is actually built.
Change it to use IS_ENABLED(CONFIG_NVME_KEYRING) checks consistently,
which should help readability and make it less error-prone. Combining
it with the check for the ctrl->opts->tls flag lets the compiler drop
all the TLS code in configurations without this feature, which also
helps runtime behavior in addition to avoiding the link failure.
To make it possible for the compiler to build the dead code, both
the tls_handshake_timeout variable and the TLS specific members
of nvme_tcp_queue need to be moved out of the #ifdef block as well,
but at least the former of these gets optimized out again.
Signed-off-by: Arnd Bergmann <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jens Axboe <[email protected]>
|
|
When the NVME target code is built-in but its TCP frontend is a loadable
module, enabling keyring support causes a link failure:
x86_64-linux-ld: vmlinux.o: in function `nvmet_ports_make':
configfs.c:(.text+0x100a211): undefined reference to `nvme_keyring_id'
The problem is that CONFIG_NVME_TARGET_TCP_TLS is a 'bool' symbol that
depends on the tristate CONFIG_NVME_TARGET_TCP, so any 'select' from
it inherits the state of the tristate symbol rather than the intended
CONFIG_NVME_TARGET one that contains the actual call.
The same thing is true for CONFIG_KEYS, which itself is required for
NVME_KEYRING.
Signed-off-by: Arnd Bergmann <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jens Axboe <[email protected]>
|
|
In configurations without CONFIG_NVME_TARGET_TCP_TLS, the keyring
code might not be available, or using it will result in a runtime
failure:
x86_64-linux-ld: vmlinux.o: in function `nvmet_ports_make':
configfs.c:(.text+0x100a211): undefined reference to `nvme_keyring_id'
Add a check to ensure we only check the keyring if there is a chance
of it being used, which avoids both the runtime and link-time
problems.
Signed-off-by: Arnd Bergmann <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jens Axboe <[email protected]>
|
|
Pull NVMe fixes from Keith:
"nvme fixes for Linux 6.7
- TCP TLS fixes (Hannes)
- Authentifaction fixes (Mark, Hannes)
- Properly terminate target names (Christoph)"
* tag 'nvme-6.7-2023-11-22' of git://git.infradead.org/nvme:
nvme: move nvme_stop_keep_alive() back to original position
nvmet-tcp: always initialize tls_handshake_tmo_work
nvmet: nul-terminate the NQNs passed in the connect command
nvme: blank out authentication fabrics options if not configured
nvme: catch errors from nvme_configure_metadata()
nvme-tcp: only evaluate 'tls' option if TLS is selected
nvme-auth: set explanation code for failure2 msgs
nvme-auth: unlock mutex in one place only
|
|
Stopping keep-alive not only stops the keep-alive workqueue,
but also needs to be synchronized with I/O termination as we
must not send a keep-alive command after all I/O had been
terminated.
So to avoid any regressions move the call to stop_keep_alive()
back to its original position and ensure that keep-alive is
correctly stopped failing to setup the admin queue.
Fixes: 4733b65d82bd ("nvme: start keep-alive after admin queue setup")
Suggested-by: Sagi Grimberg <[email protected]>
Signed-off-by: Hannes Reinecke <[email protected]>
Reviewed-by: Sagi Grimberg <[email protected]>
Signed-off-by: Keith Busch <[email protected]>
|