aboutsummaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)AuthorFilesLines
2020-02-03bnxt_en: Fix TC queue mapping.Michael Chan1-1/+1
The driver currently only calls netdev_set_tc_queue when the number of TCs is greater than 1. Instead, the comparison should be greater than or equal to 1. Even with 1 TC, we need to set the queue mapping. This bug can cause warnings when the number of TCs is changed back to 1. Fixes: 7809592d3e2e ("bnxt_en: Enable MSIX early in bnxt_init_one().") Signed-off-by: Michael Chan <[email protected]> Signed-off-by: Jakub Kicinski <[email protected]>
2020-02-03bnxt_en: Fix logic that disables Bus Master during firmware reset.Vasundhara Volam1-4/+7
The current logic that calls pci_disable_device() in __bnxt_close_nic() during firmware reset is flawed. If firmware is still alive, we're disabling the device too early, causing some firmware commands to not reach the firmware. Fix it by moving the logic to bnxt_reset_close(). If firmware is in fatal condition, we call pci_disable_device() before we free any of the rings to prevent DMA corruption of the freed rings. If firmware is still alive, we call pci_disable_device() after the last firmware message has been sent. Fixes: 3bc7d4a352ef ("bnxt_en: Add BNXT_STATE_IN_FW_RESET state.") Signed-off-by: Vasundhara Volam <[email protected]> Signed-off-by: Michael Chan <[email protected]> Signed-off-by: Jakub Kicinski <[email protected]>
2020-02-03bnxt_en: Fix RDMA driver failure with SRIOV after firmware reset.Michael Chan1-2/+5
bnxt_ulp_start() needs to be called before SRIOV is re-enabled after firmware reset. Re-enabling SRIOV may consume all the resources and may cause the RDMA driver to fail to get MSIX and other resources. Fix it by calling bnxt_ulp_start() first before calling bnxt_reenable_sriov(). We re-arrange the logic so that we call bnxt_ulp_start() and bnxt_reenable_sriov() in proper sequence in bnxt_fw_reset_task() and bnxt_open(). The former is the normal coordinated firmware reset sequence and the latter is firmware reset while the function is down. This new logic is now more straight forward and will now fix both scenarios. Fixes: f3a6d206c25a ("bnxt_en: Call bnxt_ulp_stop()/bnxt_ulp_start() during error recovery.") Reported-by: Vasundhara Volam <[email protected]> Signed-off-by: Michael Chan <[email protected]> Signed-off-by: Jakub Kicinski <[email protected]>
2020-02-03bnxt_en: Refactor logic to re-enable SRIOV after firmware reset detected.Michael Chan1-7/+12
Put the current logic in bnxt_open() to re-enable SRIOV after detecting firmware reset into a new function bnxt_reenable_sriov(). This call needs to be invoked in the firmware reset path also in the next patch. Signed-off-by: Michael Chan <[email protected]> Signed-off-by: Jakub Kicinski <[email protected]>
2020-02-03net: stmmac: Delete txtimer in suspend()Nicolin Chen1-0/+4
When running v5.5 with a rootfs on NFS, memory abort may happen in the system resume stage: Unable to handle kernel paging request at virtual address dead00000000012a [dead00000000012a] address between user and kernel address ranges pc : run_timer_softirq+0x334/0x3d8 lr : run_timer_softirq+0x244/0x3d8 x1 : ffff800011cafe80 x0 : dead000000000122 Call trace: run_timer_softirq+0x334/0x3d8 efi_header_end+0x114/0x234 irq_exit+0xd0/0xd8 __handle_domain_irq+0x60/0xb0 gic_handle_irq+0x58/0xa8 el1_irq+0xb8/0x180 arch_cpu_idle+0x10/0x18 do_idle+0x1d8/0x2b0 cpu_startup_entry+0x24/0x40 secondary_start_kernel+0x1b4/0x208 Code: f9000693 a9400660 f9000020 b4000040 (f9000401) ---[ end trace bb83ceeb4c482071 ]--- Kernel panic - not syncing: Fatal exception in interrupt SMP: stopping secondary CPUs SMP: failed to stop secondary CPUs 2-3 Kernel Offset: disabled CPU features: 0x00002,2300aa30 Memory Limit: none ---[ end Kernel panic - not syncing: Fatal exception in interrupt ]--- It's found that stmmac_xmit() and stmmac_resume() sometimes might run concurrently, possibly resulting in a race condition between mod_timer() and setup_timer(), being called by stmmac_xmit() and stmmac_resume() respectively. Since the resume() runs setup_timer() every time, it'd be safer to have del_timer_sync() in the suspend() as the counterpart. Signed-off-by: Nicolin Chen <[email protected]> Signed-off-by: Jakub Kicinski <[email protected]>
2020-02-03Merge branch 'stable/for-linus-5.6' of ↵Linus Torvalds1-4/+5
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/ibft Pull ibft update from Konrad Rzeszutek Wilk: "Adhere to the iBFT spec and extend the structure to handle more than two NICs" * 'stable/for-linus-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/ibft: iscsi_ibft: Don't limits Targets and NICs to two
2020-02-03Merge tag 'vfio-v5.6-rc1' of git://github.com/awilliam/linux-vfioLinus Torvalds4-7/+9
Pull VFIO updates from Alex Williamson: - Fix nvlink error path (Alexey Kardashevskiy) - Update nvlink and spapr to use mmgrab() (Julia Lawall) - Update static declaration (Ben Dooks) - Annotate __iomem to fix sparse warnings (Ben Dooks) * tag 'vfio-v5.6-rc1' of git://github.com/awilliam/linux-vfio: vfio: platform: fix __iomem in vfio_platform_amdxgbe.c vfio/mdev: make create attribute static vfio/spapr_tce: use mmgrab vfio: vfio_pci_nvlink2: use mmgrab vfio/spapr/nvlink2: Skip unpinning pages on error exit
2020-02-03Merge tag 'clk-for-linus' of ↵Linus Torvalds103-1604/+12750
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux Pull clk updates from Stephen Boyd: "There are a few changes to the core framework this time around, in addition to the normal collection of driver updates to support new SoCs, fix incorrect data, and convert various drivers to clk_hw based APIs. In the core, we allow clk_ops::init() to return an error code now so that we can fail clk registration if the callback does something like fail to allocate memory. We also add a new "terminate" clk_op so that things done in clk_ops::init() can be undone, e.g. free memory. We also spit out a warning now when critical clks fail to enable and we support changing clk rates and enable/disable state through debugfs when developers compile the kernel themselves. On the driver front, we get support for what seems like a lot of Qualcomm and NXP SoCs given that those vendors dominate the diffstat. There are a couple new drivers for Xilinx and Amlogic SoCs too. The updates are all small things like fixing the way glitch free muxes switch parents, avoiding div-by-zero problems, or fixing data like parent names. See the updates section below for more details. Finally, the "basic" clk types have been converted to support specifying parents with clk_hw pointers. This work includes an overhaul of the fixed-rate clk type to be more modern by using clk_hw APIs. Core: - Let clk_ops::init() return an error code - Add a clk_ops::terminate() callback to undo clk_ops::init() - Warn about critical clks that fail to enable or prepare - Support dangerous debugfs actions on clks with dead code New Drivers: - Support for Xilinx Versal platform clks - Display clk controller on qcom sc7180 - Video clk controller on qcom sc7180 - Graphics clk controller on qcom sc7180 - CPU PLLs for qcom msm8916 - Move qcom msm8974 gfx3d clk to RPM control - Display port clk support on qcom sdm845 SoCs - Global clk controller on qcom ipq6018 - Add a driver for BCLK of Freescale SAI cores - Add cam, vpe and sgx clock support for TI dra7 - Add aess clock support for TI omap5 - Enable clks for CPUfreq on Allwinner A64 SoCs - Add Amlogic meson8b DDR clock controller - Add input clocks to Amlogic meson8b controllers - Add SPIBSC (SPI FLASH) clock on Renesas RZ/A2 - i.MX8MP clk driver support Updates: - Convert gpio, fixed-factor, mux, gate, divider basic clks to hw based APIs - Detect more PRMCU variants in ux500 driver - Adjust the composite clk type to new way of describing clk parents - Fixes for clk controllers on qcom msm8998 SoCs - Fix gmac main clock for TI dra7 - Move TI dra7-atl clock header to correct location - Fix hidden node name dependency on TI clkctrl clocks - Fix Amlogic meson8b mali clock update using the glitch free mux - Fix Amlogic pll driver division by zero at init - Prepare for split of Renesas R-Car H3 ES1.x and ES2.0+ config symbols - Switch more i.MX clk drivers to clk_hw based APIs - Disable non-functional divider between pll4_audio_div and pll4_post_div on imx6q - Fix watchdog2 clock name typo in imx7ulp clock driver - Set CLK_GET_RATE_NOCACHE flag for DRAM related clocks on i.MX8M SoCs - Suppress bind attrs for i.MX8M clock driver - Add a big comment in imx8qxp-lpcg driver to tell why devm_platform_ioremap_resource() shouldn't be used for the driver - A correction on i.MX8MN usb1_ctrl parent clock setting" * tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (140 commits) dt/bindings: clk: fsl,plldig: Drop 'bindings' from schema id clk: ls1028a: Fix warning on clamp() usage clk: qoriq: add ls1088a hwaccel clocks support clk: ls1028a: Add clock driver for Display output interface dt/bindings: clk: Add YAML schemas for LS1028A Display Clock bindings clk: fsl-sai: new driver dt-bindings: clock: document the fsl-sai driver clk: composite: add _register_composite_pdata() variants clk: qcom: rpmh: Sort OF match table dt-bindings: fix warnings in validation of qcom,gcc.yaml dt-binding: fix compilation error of the example in qcom,gcc.yaml clk: zynqmp: Add support for clock with CLK_DIVIDER_POWER_OF_TWO flag clk: zynqmp: Fix divider calculation clk: zynqmp: Add support for get max divider clk: zynqmp: Warn user if clock user are more than allowed clk: zynqmp: Extend driver for versal dt-bindings: clock: Add bindings for versal clock driver clk: ti: clkctrl: Fix hidden dependency to node name clk: ti: add clkctrl data dra7 sgx clk: ti: omap5: Add missing AESS clock ...
2020-02-03Merge branch 'for-linus' of ↵Linus Torvalds9-55/+380
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input Pull input updates from Dmitry Torokhov: - a driver for SGI IOC3 PS/2 controller - updates to driver for FocalTech FT5x06 series touch screen controllers - other assorted fixes * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: Input: synaptics-rmi4 - switch to reduced reporting mode dt-bindings: touchscreen: Convert Goodix touchscreen to json-schema dt-bindings: touchscreen: Add touchscreen schema Input: add IOC3 serio driver Input: axp20x-pek - enable wakeup for all AXP variants Input: axp20x-pek - respect userspace wakeup configuration Input: ads7846 - use new `delay` structure for SPI transfer delays Input: edt-ft5x06 - use pm core to enable/disable the wake irq Input: edt-ft5x06 - make wakeup-source switchable Input: edt-ft5x06 - document wakeup-source capability Input: edt-ft5x06 - alphabetical include reorder Input: edt-ft5x06 - work around first register access error Input: apbps2 - add __iomem to register struct Input: axp20x-pek - make device attributes static Input: elants_i2c - check Remark ID when attempting firmware update
2020-02-03clk: qcom: Don't overwrite 'cfg' in clk_rcg2_dfs_populate_freq()Stephen Boyd1-4/+4
The DFS frequency table logic overwrites 'cfg' while detecting the parent clk and then later on in clk_rcg2_dfs_populate_freq() we use that same variable to figure out the mode of the clk, either MND or not. Add a new variable to hold the parent clk bit so that 'cfg' is left untouched for use later. This fixes problems in detecting the supported frequencies for any clks in DFS mode. Fixes: cc4f6944d0e3 ("clk: qcom: Add support for RCG to register for DFS") Reported-by: Rajendra Nayak <[email protected]> Signed-off-by: Stephen Boyd <[email protected]> Link: https://lkml.kernel.org/r/[email protected] Tested-by: Rajendra Nayak <[email protected]>
2020-02-03clk: ls1028a: Fix warning on clamp() usageStephen Boyd1-2/+2
These constants are used in clamp() with the value being clamped an unsigned long. Make them unsigned long defines so that clamp() doesn't complain about comparing different types. In file included from include/linux/list.h:9, from include/linux/kobject.h:19, from include/linux/of.h:17, from include/linux/clk-provider.h:9, from drivers/clk/clk-plldig.c:8: drivers/clk/clk-plldig.c: In function 'plldig_determine_rate': include/linux/kernel.h:835:29: warning: comparison of distinct pointer types lacks a cast 835 | (!!(sizeof((typeof(x) *)1 == (typeof(y) *)1))) | Reported-by: Stephen Rothwell <[email protected]> Cc: Wen He <[email protected]> Fixes: d37010a3c162 ("clk: ls1028a: Add clock driver for Display output interface") Signed-off-by: Stephen Boyd <[email protected]> Link: https://lkml.kernel.org/r/[email protected]
2020-02-03rtw88: Fix return value of rtw_wow_check_fw_statusChin-Yen Lee1-12/+11
Clang warns that ret is used uninitialzed. And we found that actually the return type should be "int" instead of "bool". Fixes: 44bc17f7f5b3 ("rtw88: support wowlan feature for 8822c") Link: https://github.com/ClangBuiltLinux/linux/issues/850 Reported-by: Nathan Chancellor <[email protected]> Signed-off-by: Chin-Yen Lee <[email protected]> Signed-off-by: Yan-Hsuan Chuang <[email protected]> Reviewed-by: Nathan Chancellor <[email protected]> Tested-by: Nathan Chancellor <[email protected]> # build Signed-off-by: Kalle Valo <[email protected]>
2020-02-03iwlwifi: d3: read all FW CPUs error infoMordechay Goodstein1-12/+40
Continue the wakeup flow only if no FW CPUs have an error If we don't check for error in all FW CPUs the driver can think based on one CPU that the FW is operational and try to access and send commands. Also, handle the error_id endianness correctly as le32 Signed-off-by: Mordechay Goodstein <[email protected]> Signed-off-by: Luca Coelho <[email protected]> Signed-off-by: Kalle Valo <[email protected]>
2020-02-03iwlwifi: mvm: fix TDLS discovery with the new firmware APIEmmanuel Grumbach4-15/+72
I changed the API for asking for a session protection but I omitted the TDLS flows. Fix that now. Note that for the TDLS flow, we need to block until the session protection actually starts, so add this option to iwl_mvm_schedule_session_protection. This patch fixes a firmware assert in the TDLS flow since the old TIME_EVENT_CMD is not supported anymore by newer firwmare versions. Signed-off-by: Emmanuel Grumbach <[email protected]> Fixes: fe959c7b2049 ("iwlwifi: mvm: use the new session protection command") Signed-off-by: Luca Coelho <[email protected]> Signed-off-by: Kalle Valo <[email protected]>
2020-02-03iwlwifi: mvm: Check the sta is not NULL in iwl_mvm_cfg_he_sta()Andrei Otcheretianski1-5/+3
Fix a kernel panic by checking that the sta is not NULL. This could happen during a reconfig flow, as mac80211 moves the sta between all the states without really checking if the previous state was successfully set. So, if for some reason we failed to add back the station, subsequent calls to sta_state() callback will be done when the station is NULL. This would result in a following panic: BUG: unable to handle kernel NULL pointer dereference at 0000000000000040 IP: iwl_mvm_cfg_he_sta+0xfc/0x690 [iwlmvm] [..] Call Trace: iwl_mvm_mac_sta_state+0x629/0x6f0 [iwlmvm] drv_sta_state+0xf4/0x950 [mac80211] ieee80211_reconfig+0xa12/0x2180 [mac80211] ieee80211_restart_work+0xbb/0xe0 [mac80211] process_one_work+0x1e2/0x610 worker_thread+0x4d/0x3e0 [..] Signed-off-by: Andrei Otcheretianski <[email protected]> Signed-off-by: Luca Coelho <[email protected]> Signed-off-by: Kalle Valo <[email protected]>
2020-02-03iwlwifi: mvm: avoid use after free for pmsr requestAvraham Stern1-1/+4
When a FTM request is aborted, the driver sends the abort command to the fw and waits for a response. When the response arrives, the driver calls cfg80211_pmsr_complete() for that request. However, cfg80211 frees the requested data immediately after sending the abort command, so this may lead to use after free. Fix it by clearing the request data in the driver when the abort command arrives and ignoring the fw notification that will come afterwards. Signed-off-by: Avraham Stern <[email protected]> Fixes: fc36ffda3267 ("iwlwifi: mvm: support FTM initiator") Signed-off-by: Luca Coelho <[email protected]> Signed-off-by: Kalle Valo <[email protected]>
2020-02-03iwlwifi: mvm: update the DTS measurement typeGolan Ben Ami1-3/+3
Till now, the driver asked the fw for a DTS measurement in automatic mode. This triggered a flow in which the fw actively measured the temperature. This is not needed anymore, as the fw performs measurements by itself, without the driver triggering them, and the current cadence in which the fw performs such measurements is sufficient. In addition, in some time-sensitive scenarios, in which the driver asks the fw for an active measurement twice in a short time (<100ms), the fw asserts with code 0x20100801. Change the DTS measurement to _WITHOUT_MEASURE instead, so the fw will respond with the last measurement it has performed. Signed-off-by: Golan Ben Ami <[email protected]> Signed-off-by: Luca Coelho <[email protected]> Signed-off-by: Kalle Valo <[email protected]>
2020-02-03iwlwifi: don't throw error when trying to remove IGTKLuca Coelho1-3/+7
The IGTK keys are only removed by mac80211 after it has already removed the AP station. This causes the driver to throw an error because mac80211 is trying to remove the IGTK when the station doesn't exist anymore. The firmware is aware that the station has been removed and can deal with it the next time we try to add an IGTK for a station, so we shouldn't try to remove the key if the station ID is IWL_MVM_INVALID_STA. Do this by removing the check for mvm_sta before calling iwl_mvm_send_sta_igtk() and check return from that function gracefully if the station ID is invalid. Cc: [email protected] # 4.12+ Signed-off-by: Luca Coelho <[email protected]> Signed-off-by: Kalle Valo <[email protected]>
2020-02-03iwlwifi: mvm: Fix thermal zone registrationAndrei Otcheretianski1-1/+3
Use a unique name when registering a thermal zone. Otherwise, with multiple NICS, we hit the following warning during the unregistration. WARNING: CPU: 2 PID: 3525 at fs/sysfs/group.c:255 RIP: 0010:sysfs_remove_group+0x80/0x90 Call Trace: dpm_sysfs_remove+0x57/0x60 device_del+0x5a/0x350 ? sscanf+0x4e/0x70 device_unregister+0x1a/0x60 hwmon_device_unregister+0x4a/0xa0 thermal_remove_hwmon_sysfs+0x175/0x1d0 thermal_zone_device_unregister+0x188/0x1e0 iwl_mvm_thermal_exit+0xe7/0x100 [iwlmvm] iwl_op_mode_mvm_stop+0x27/0x180 [iwlmvm] _iwl_op_mode_stop.isra.3+0x2b/0x50 [iwlwifi] iwl_opmode_deregister+0x90/0xa0 [iwlwifi] __exit_compat+0x10/0x2c7 [iwlmvm] __x64_sys_delete_module+0x13f/0x270 do_syscall_64+0x5a/0x110 entry_SYSCALL_64_after_hwframe+0x44/0xa9 Signed-off-by: Andrei Otcheretianski <[email protected]> Signed-off-by: Luca Coelho <[email protected]> Signed-off-by: Kalle Valo <[email protected]>
2020-02-04nvme-pci: remove nvmeq->tagsChristoph Hellwig1-15/+8
There is no real need to have a pointer to the tagset in struct nvme_queue, as we only need it in a single place, and that place can derive the used tagset from the device and qid trivially. This fixes a problem with stale pointer exposure when tagsets are reset, and also shrinks the nvme_queue structure. It also matches what most other transports have done since day 1. Reported-by: Edmund Nadolski <[email protected]> Signed-off-by: Christoph Hellwig <[email protected]> Signed-off-by: Keith Busch <[email protected]>
2020-02-04nvmet: fix dsm failure when payload does not match sgl descriptorSagi Grimberg4-2/+14
The host is allowed to pass the controller an sgl describing a buffer that is larger than the dsm payload itself, allow it when executing dsm. Reported-by: Dakshaja Uppalapati <[email protected]> Reviewed-by: Christoph Hellwig <[email protected]>, Reviewed-by: Max Gurtovoy <[email protected]> Signed-off-by: Sagi Grimberg <[email protected]> Signed-off-by: Keith Busch <[email protected]>
2020-02-04nvmet: Pass lockdep expression to RCU listsAmol Grover1-2/+4
ctrl->subsys->namespaces and subsys->namespaces are traversed with list_for_each_entry_rcu outside an RCU read-side critical section but under the protection of ctrl->subsys->lock and subsys->lock respectively. Hence, add the corresponding lockdep expression to the list traversal primitive to silence false-positive lockdep warnings, and harden RCU lists. Reported-by: kbuild test robot <[email protected]> Reviewed-by: Joel Fernandes (Google) <[email protected]> Signed-off-by: Amol Grover <[email protected]> Signed-off-by: Keith Busch <[email protected]>
2020-02-04kbuild: rename hostprogs-y/always to hostprogs/always-yMasahiro Yamada4-4/+4
In old days, the "host-progs" syntax was used for specifying host programs. It was renamed to the current "hostprogs-y" in 2004. It is typically useful in scripts/Makefile because it allows Kbuild to selectively compile host programs based on the kernel configuration. This commit renames like follows: always -> always-y hostprogs-y -> hostprogs So, scripts/Makefile will look like this: always-$(CONFIG_BUILD_BIN2C) += ... always-$(CONFIG_KALLSYMS) += ... ... hostprogs := $(always-y) $(always-m) I think this makes more sense because a host program is always a host program, irrespective of the kernel configuration. We want to specify which ones to compile by CONFIG options, so always-y will be handier. The "always", "hostprogs-y", "hostprogs-m" will be kept for backward compatibility for a while. Signed-off-by: Masahiro Yamada <[email protected]>
2020-02-03platform/chrome: cros_ec: Match implementation with headersEnric Balletbo i Serra7-0/+30
The 'cros_ec' core driver is the common interface for the cros_ec transport drivers to do the shared operations to register, unregister, suspend, resume and handle_event. The interface is provided by including the header 'include/linux/platform_data/cros_ec_proto.h', however, instead of have the implementation of these functions in cros_ec_proto.c, it is in 'cros_ec.c', which is a different kernel module. Apart from being a bad practice, this can induce confusions allowing the users of the cros_ec protocol to call these functions. The register, unregister, suspend, resume and handle_event functions *should* only be called by the different transport drivers (i2c, spi, lpc, etc.), so make this a bit less confusing by moving these functions from the public in-kernel space to a private include in platform/chrome, and then, the interface for cros_ec module and for the cros_ec_proto module is clean. Signed-off-by: Enric Balletbo i Serra <[email protected]> Signed-off-by: Benson Leung <[email protected]>
2020-02-03Merge tag 'char-misc-5.6-rc1-2' of ↵Linus Torvalds1-1/+1
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc Pull char/misc fix from Greg KH: "Here is a single patch, that fixes up a commit that came in the previous char/misc merge. It fixes a bug in the hpet driver that everyone keeps tripping over in their automated testing. Good thing is, people are catching it. Bad thing it wasn't caught by anyone testing before this. Oh well... This has been in linux-next for a few days with no reported issues" * tag 'char-misc-5.6-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: char: hpet: Fix out-of-bounds read bug
2020-02-03Merge tag 'backlight-next-5.6' of ↵Linus Torvalds3-11/+18
git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight Pull backlight updates from Lee Jones: "Fix-ups: - Remove superfluous code in ams369fg06 - Convert over to GPIO descriptor (gpiod) in bd6107 Bug Fixes: - Fix unsigned comparison to less than zero in qcom-wled" * tag 'backlight-next-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight: backlight: qcom-wled: Fix unsigned comparison to zero backlight: bd6107: Convert to use GPIO descriptor backlight: ams369fg06: Drop GPIO include
2020-02-03Merge tag 'mfd-next-5.6' of ↵Linus Torvalds31-335/+1452
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd Pull MFD updates from Lee Jones: "New Drivers: - Add support for ROHM BD71828 PMICs and GPIOs - Add support for Qualcomm Aqstic Audio Codecs WCD9340 and WCD9341 New Device Support: - Add support for BD71828 to BD70528 RTC driver - Add support for Intel's Jasper Lake to LPSS PCI New Functionality: - Add support for Power Key to ROHM BD71828 - Add support for Clocks to ROHM BD71828 - Add support for GPIOs to Dialog DA9062 - Add support for USB PD Notify to ChromiumOS EC - Allow callers to specify args when requesting regmap lookup; syscon Fix-ups: - Improve error handling and sanity checking; atmel-hlcdc, dln2 - Device Tree support/documentation; bd71828, da9062, xylon,logicvc, ab8500, max14577, atmel-usart - Match devices using platform IDs; bd7xxxx - Refactor BD718x7 regulator component; bd718x7-regulator - Use standard interfaces/helpers; syscon, sm501 - Trivial (whitespace, spelling, etc); ab8500-core, Kconfig - Remove unused code; db8500-prcmu, tqmx86 - Wait until boot has finished before accessing registers; madera-core - Provide missing register value defaults; cs47l15-tables - Allow more time for hardware to reset; madera-core Bug Fixes: - Fix erroneous register values; rohm-bd70528 - Fix register volatility; axp20x, rn5t618 - Fix Kconfig dependencies; MFD_MAX77650 - Fix incorrect compatible string; da9062-core - Fix syscon_regmap_lookup_by_phandle_args() stub; syscon" * tag 'mfd-next-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (41 commits) mfd: syscon: Fix syscon_regmap_lookup_by_phandle_args() dummy mfd: wcd934x: Add support to wcd9340/wcd9341 codec mfd: syscon: Add arguments support for syscon reference mfd: rn5t618: Mark ADC control register volatile dt-bindings: atmel-usart: Add microchip,sam9x60-{usart, dbgu} dt-bindings: atmel-usart: Remove wildcard mfd: cros_ec: Add cros-usbpd-notify subdevice mfd: da9062: Fix watchdog compatible string mfd: madera: Allow more time for hardware reset mfd: cs47l15: Add missing register default mfd: madera: Wait for boot done before accessing any other registers mfd: Kconfig: Rename Samsung to lowercase mfd: tqmx86: remove set but not used variable 'i2c_ien' mfd: dbx500-prcmu: Drop DSI pll clock functions mfd: dbx500-prcmu: Drop set_display_clocks() mfd: max77650: Select REGMAP_IRQ in Kconfig mfd: axp20x: Mark AXP20X_VBUS_IPSOUT_MGMT as volatile mfd: ab8500: Fix ab8500-clk typo mfd: intel-lpss: Add Intel Jasper Lake PCI IDs dt-bindings: mfd: max14577: Add reference to max14040_battery.txt descriptions ...
2020-02-03Merge tag 'hyperv-next-signed' of ↵Linus Torvalds11-77/+479
git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux Pull Hyper-V updates from Sasha Levin: - Most of the commits here are work to enable host-initiated hibernation support by Dexuan Cui. - Fix for a warning shown when host sends non-aligned balloon requests by Tianyu Lan. * tag 'hyperv-next-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux: hv_utils: Add the support of hibernation hv_utils: Support host-initiated hibernation request hv_utils: Support host-initiated restart request Tools: hv: Reopen the devices if read() or write() returns errors video: hyperv: hyperv_fb: Use physical memory for fb on HyperV Gen 1 VMs. Drivers: hv: vmbus: Ignore CHANNELMSG_TL_CONNECT_RESULT(23) video: hyperv_fb: Fix hibernation for the deferred IO feature Input: hyperv-keyboard: Add the support of hibernation hv_balloon: Balloon up according to request page number
2020-02-03fs: Enable bmap() function to properly return errorsCarlos Maiolino1-6/+10
By now, bmap() will either return the physical block number related to the requested file offset or 0 in case of error or the requested offset maps into a hole. This patch makes the needed changes to enable bmap() to proper return errors, using the return value as an error return, and now, a pointer must be passed to bmap() to be filled with the mapped physical block. It will change the behavior of bmap() on return: - negative value in case of error - zero on success or map fell into a hole In case of a hole, the *block will be zero too Since this is a prep patch, by now, the only error return is -EINVAL if ->bmap doesn't exist. Reviewed-by: Christoph Hellwig <[email protected]> Signed-off-by: Carlos Maiolino <[email protected]> Signed-off-by: Al Viro <[email protected]>
2020-02-03drm/nouveau/kms/gv100-: avoid sending a core update until the first modesetBen Skeggs2-6/+2
The OR routing logic in NVKM does not expect to receive supervisor interrupts until the DD has provided consistent information on the ORs it's using and the EVO/NVD assembly state to match. The combination of changing window ownership + core channel update during display init triggered a situation where we'd disconnect an OR from the pad it was meant to still be driving on some systems. Signed-off-by: Ben Skeggs <[email protected]>
2020-02-03drm/nouveau/kms/gv100-: move window ownership setup into modesetting pathBen Skeggs4-6/+44
For various complicated reasons, we need to avoid sending a core update method during display init. Something, which we've been required to do on GV100 and up because we've been assigning windows to heads there and the HW is rather picky about when that's allowed. This moves window assignment into the modesetting path at a point where it's much safer to send our first update methods to NVDisplay. Signed-off-by: Ben Skeggs <[email protected]>
2020-02-03drm/nouveau/disp/gv100-: halt NV_PDISP_FE_RM_INTR_STAT_CTRL_DISP_ERROR stormsBen Skeggs1-0/+6
Signed-off-by: Ben Skeggs <[email protected]>
2020-02-03i2c: designware: Add ACPI HID for Hisilicon Hip08-Lite I2C controllerHanjun Guo1-0/+1
Add ACPI HID HISI02A3 for Hisilicon Hip08 Lite, which has different clock frequency from Hip08 for I2C controller. Tested-by: Sheng Feng <[email protected]> Signed-off-by: Hanjun Guo <[email protected]> Acked-by: Nikula <[email protected]> Reviewed-by: Andy Shevchenko <[email protected]> Signed-off-by: Rafael J. Wysocki <[email protected]>
2020-02-03ACPI / APD: Add clock frequency for Hisilicon Hip08-Lite I2C controllerHanjun Guo1-0/+6
I2C clock frequency of Designware ip for Hisilicon Hip08 Lite is 125M, use a new ACPI HID to enable it. Tested-by: Sheng Feng <[email protected]> Signed-off-by: Hanjun Guo <[email protected]> Reviewed-by: Jarkko Nikula <[email protected]> Signed-off-by: Rafael J. Wysocki <[email protected]>
2020-02-03intel_idle: Introduce 'states_off' module parameterRafael J. Wysocki1-3/+20
In certain system configurations it may not be desirable to use some C-states assumed to be available by intel_idle and the driver needs to be prevented from using them even before the cpuidle sysfs interface becomes accessible to user space. Currently, the only way to achieve that is by setting the 'max_cstate' module parameter to a value lower than the index of the shallowest of the C-states in question, but that may be overly intrusive, because it effectively makes all of the idle states deeper than the 'max_cstate' one go away (and the C-state to avoid may be in the middle of the range normally regarded as available). To allow that limitation to be overcome, introduce a new module parameter called 'states_off' to represent a list of idle states to be disabled by default in the form of a bitmask and update the documentation to cover it. Signed-off-by: Rafael J. Wysocki <[email protected]>
2020-02-03intel_idle: Introduce 'use_acpi' module parameterRafael J. Wysocki1-2/+9
For diagnostics, it is generally useful to be able to make intel_idle take the system's ACPI tables into consideration even if that is not required for the processor model in there, so introduce a new module parameter, 'use_acpi', to make that happen and update the documentation to cover it. While at it, fix the 'no_acpi' module parameter name in the documentation. Signed-off-by: Rafael J. Wysocki <[email protected]>
2020-02-03irqchip/gic-v3-its: Reference to its_invall_cmd descriptor when building INVALLZenghui Yu1-1/+1
It looks like an obvious mistake to use its_mapc_cmd descriptor when building the INVALL command block. It so far worked by luck because both its_mapc_cmd.col and its_invall_cmd.col sit at the same offset of the ITS command descriptor, but we should not rely on it. Fixes: cc2d3216f53c ("irqchip: GICv3: ITS command queue") Signed-off-by: Zenghui Yu <[email protected]> Signed-off-by: Marc Zyngier <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2020-02-03dmaengine: Cleanups for the slave <-> channel symlink supportPeter Ujfalusi1-9/+9
No need to use goto to jump over the return chan ? chan : ERR_PTR(-EPROBE_DEFER); We can just revert the check and return right there. Do not fail the channel request if the chan->name allocation fails, but print a warning about it. Change the dev_err to dev_warn if sysfs_create_link() fails as it is not fatal. Only attempt to remove the DMA_SLAVE_NAME symlink if it is created - or it was attempted to be created. Signed-off-by: Peter Ujfalusi <[email protected]> Reviewed-by: Geert Uytterhoeven <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Vinod Koul <[email protected]>
2020-02-03dmaengine: fix null ptr check for __dma_async_device_channel_register()Dave Jiang1-0/+3
Add check to pointer after assignment before accessing members. Fixes: d2fb0a043838: ("dmaengine: break out channel registration") Reported-by: Dan Carpenter <[email protected]> Signed-off-by: Dave Jiang <[email protected]> Link: https://lore.kernel.org/r/158049351973.45445.3291586905226032744.stgit@djiang5-desk3.ch.intel.com Signed-off-by: Vinod Koul <[email protected]>
2020-02-03dmaengine: idxd: fix boolconv.cocci warningskbuild test robot1-1/+1
Remove unneeded conversion to bool Generated by: scripts/coccinelle/misc/boolconv.cocci CC: Dave Jiang <[email protected]> Signed-off-by: kbuild test robot <[email protected]> Signed-off-by: Julia Lawall <[email protected]> Acked-by: Dave Jiang <[email protected]> Link: https://lore.kernel.org/r/alpine.DEB.2.21.2001301543150.7476@hadrien Signed-off-by: Vinod Koul <[email protected]>
2020-02-02Merge tag 'leds-5.6-rc1' of ↵Linus Torvalds9-92/+365
git://git.kernel.org/pub/scm/linux/kernel/git/pavel/linux-leds Pull LED updates from Pavel Machek: - New driver for TI TPS6105X - Add managed API to get a LED from a device driver - Misc fixes and updates * tag 'leds-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/pavel/linux-leds: (22 commits) leds: lm3692x: Disable chip on brightness 0 leds: lm3692x: Split out lm3692x_leds_disable leds: lm3692x: Move lm3692x_init and rename to lm3692x_leds_enable leds: lm3692x: Make sure we don't exceed the maximum LED current dt: bindings: lm3692x: Add led-max-microamp property leds: lm3692x: Allow to configure over voltage protection dt: bindings: lm3692x: Add ti,ovp-microvolt property leds: populate the device's of_node leds: Add managed API to get a LED from a device driver leds: Add of_led_get() and led_put() leds: lm3532: add pointer to documentation and fix typo leds: lm3532: use extended registration so that LED can be used for backlight leds: lm3642: remove warnings for bad strtol, cleanup gotos leds: rb532: cleanup whitespace ledtrig-pattern: fix email address quoting in MODULE_AUTHOR() dt-bindings: mfd: update TI tps6105x chip bindings leds: tps6105x: add driver for MFD chip LED mode led: max77650: add of_match table leds: bd2802: Convert to use GPIO descriptors leds: pca963x: Fix open-drain initialization ...
2020-02-02Merge branch 'pcmcia-next' of ↵Linus Torvalds2-348/+311
git://git.kernel.org/pub/scm/linux/kernel/git/brodo/linux Pull pcmcia updates from Dominik Brodowski: "This is a series co-developed by Simon Geis and Lukas Panzer to clean up the i82092 PCMCIA device driver" * 'pcmcia-next' of git://git.kernel.org/pub/scm/linux/kernel/git/brodo/linux: PCMCIA/i82092: remove #if 0 block PCMCIA/i82092: delete enter/leave macro PCMCIA/i82092: include <linux/io.h> instead of <asm/io.h> PCMCIA/i82092: shorten the lines with over 80 characters PCMCIA/i82092: move assignment out of if condition PCMCIA/i82092: change code indentation PCMCIA/i82092: insert blank line after declarations PCMCIA/i82092: remove braces around single statement blocks PCMCIA/i82092: add/remove spaces to improve readability PCMCIA/i82092: use dev_<level> instead of printk
2020-02-01qed: Fix a error code in qed_hw_init()Dan Carpenter1-0/+1
If the qed_fw_overlay_mem_alloc() then we should return -ENOMEM instead of success. Fixes: 30d5f85895fa ("qed: FW 8.42.2.0 Add fw overlay feature") Signed-off-by: Dan Carpenter <[email protected]> Signed-off-by: Jakub Kicinski <[email protected]>
2020-02-01octeontx2-pf: Fix an IS_ERR() vs NULL bugDan Carpenter1-2/+2
The otx2_mbox_get_rsp() function never returns NULL, it returns error pointers on error. Fixes: 34bfe0ebedb7 ("octeontx2-pf: MTU, MAC and RX mode config support") Signed-off-by: Dan Carpenter <[email protected]> Signed-off-by: Jakub Kicinski <[email protected]>
2020-02-01Merge tag 'random_for_linus' of ↵Linus Torvalds1-263/+53
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random Pull random changes from Ted Ts'o: "Change /dev/random so that it uses the CRNG and only blocking if the CRNG hasn't initialized, instead of the old blocking pool. Also clean up archrandom.h, and some other miscellaneous cleanups" * tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random: (24 commits) s390x: Mark archrandom.h functions __must_check powerpc: Mark archrandom.h functions __must_check powerpc: Use bool in archrandom.h x86: Mark archrandom.h functions __must_check linux/random.h: Mark CONFIG_ARCH_RANDOM functions __must_check linux/random.h: Use false with bool linux/random.h: Remove arch_has_random, arch_has_random_seed s390: Remove arch_has_random, arch_has_random_seed powerpc: Remove arch_has_random, arch_has_random_seed x86: Remove arch_has_random, arch_has_random_seed random: remove some dead code of poolinfo random: fix typo in add_timer_randomness() random: Add and use pr_fmt() random: convert to ENTROPY_BITS for better code readability random: remove unnecessary unlikely() random: remove kernel.random.read_wakeup_threshold random: delete code to pull data into pools random: remove the blocking pool random: make /dev/random be almost like /dev/urandom random: ignore GRND_RANDOM in getentropy(2) ...
2020-02-01bcache: check return value of prio_read()Coly Li1-5/+16
Now if prio_read() failed during starting a cache set, we can print out error message in run_cache_set() and handle the failure properly. Signed-off-by: Coly Li <[email protected]> Signed-off-by: Jens Axboe <[email protected]>
2020-02-01bcache: fix incorrect data type usage in btree_flush_write()Coly Li1-1/+2
Dan Carpenter points out that from commit 2aa8c529387c ("bcache: avoid unnecessary btree nodes flushing in btree_flush_write()"), there is a incorrect data type usage which leads to the following static checker warning: drivers/md/bcache/journal.c:444 btree_flush_write() warn: 'ref_nr' unsigned <= 0 drivers/md/bcache/journal.c 422 static void btree_flush_write(struct cache_set *c) 423 { 424 struct btree *b, *t, *btree_nodes[BTREE_FLUSH_NR]; 425 unsigned int i, nr, ref_nr; ^^^^^^ 426 atomic_t *fifo_front_p, *now_fifo_front_p; 427 size_t mask; 428 429 if (c->journal.btree_flushing) 430 return; 431 432 spin_lock(&c->journal.flush_write_lock); 433 if (c->journal.btree_flushing) { 434 spin_unlock(&c->journal.flush_write_lock); 435 return; 436 } 437 c->journal.btree_flushing = true; 438 spin_unlock(&c->journal.flush_write_lock); 439 440 /* get the oldest journal entry and check its refcount */ 441 spin_lock(&c->journal.lock); 442 fifo_front_p = &fifo_front(&c->journal.pin); 443 ref_nr = atomic_read(fifo_front_p); 444 if (ref_nr <= 0) { ^^^^^^^^^^^ Unsigned can't be less than zero. 445 /* 446 * do nothing if no btree node references 447 * the oldest journal entry 448 */ 449 spin_unlock(&c->journal.lock); 450 goto out; 451 } 452 spin_unlock(&c->journal.lock); As the warning information indicates, local varaible ref_nr in unsigned int type is wrong, which does not matche atomic_read() and the "<= 0" checking. This patch fixes the above error by defining local variable ref_nr as int type. Fixes: 2aa8c529387c ("bcache: avoid unnecessary btree nodes flushing in btree_flush_write()") Reported-by: Dan Carpenter <[email protected]> Signed-off-by: Coly Li <[email protected]> Signed-off-by: Jens Axboe <[email protected]>
2020-02-01bcache: add readahead cache policy options via sysfs interfaceColy Li3-5/+37
In year 2007 high performance SSD was still expensive, in order to save more space for real workload or meta data, the readahead I/Os for non-meta data was bypassed and not cached on SSD. In now days, SSD price drops a lot and people can find larger size SSD with more comfortable price. It is unncessary to alway bypass normal readahead I/Os to save SSD space for now. This patch adds options for readahead data cache policies via sysfs file /sys/block/bcache<N>/readahead_cache_policy, the options are, - "all": cache all readahead data I/Os. - "meta-only": only cache meta data, and bypass other regular I/Os. If users want to make bcache continue to only cache readahead request for metadata and bypass regular data readahead, please set "meta-only" to this sysfs file. By default, bcache will back to cache all read- ahead requests now. Cc: [email protected] Signed-off-by: Coly Li <[email protected]> Acked-by: Eric Wheeler <[email protected]> Cc: Michael Lyle <[email protected]> Signed-off-by: Jens Axboe <[email protected]>
2020-02-01bcache: explicity type cast in bset_bkey_last()Coly Li1-1/+2
In bset.h, macro bset_bkey_last() is defined as, bkey_idx((struct bkey *) (i)->d, (i)->keys) Parameter i can be variable type of data structure, the macro always works once the type of struct i has member 'd' and 'keys'. bset_bkey_last() is also used in macro csum_set() to calculate the checksum of a on-disk data structure. When csum_set() is used to calculate checksum of on-disk bcache super block, the parameter 'i' data type is struct cache_sb_disk. Inside struct cache_sb_disk (also in struct cache_sb) the member keys is __u16 type. But bkey_idx() expects unsigned int (a 32bit width), so there is problem when sending parameters via stack to call bkey_idx(). Sparse tool from Intel 0day kbuild system reports this incompatible problem. bkey_idx() is part of user space API, so the simplest fix is to cast the (i)->keys to unsigned int type in macro bset_bkey_last(). Reported-by: kbuild test robot <[email protected]> Signed-off-by: Coly Li <[email protected]> Signed-off-by: Jens Axboe <[email protected]>
2020-02-01bcache: fix memory corruption in bch_cache_accounting_clear()Coly Li1-3/+7
Commit 83ff9318c44ba ("bcache: not use hard coded memset size in bch_cache_accounting_clear()") tries to make the code more easy to understand by removing the hard coded number with following change, void bch_cache_accounting_clear(...) { memset(&acc->total.cache_hits, 0, - sizeof(unsigned long) * 7); + sizeof(struct cache_stats)); } Unfortunately the change was wrong (it also tells us the original code was not easy to correctly understand). The hard coded number 7 is used because in struct cache_stats, 15 struct cache_stats { 16 struct kobject kobj; 17 18 unsigned long cache_hits; 19 unsigned long cache_misses; 20 unsigned long cache_bypass_hits; 21 unsigned long cache_bypass_misses; 22 unsigned long cache_readaheads; 23 unsigned long cache_miss_collisions; 24 unsigned long sectors_bypassed; 25 26 unsigned int rescale; 27 }; only members in LINE 18-24 want to be set to 0. It is wrong to use 'sizeof(struct cache_stats)' to replace 'sizeof(unsigned long) * 7), the memory objects behind acc->total is staled by this change. Сорокин Артем Сергеевич reports that by the following steps, kernel panic will be triggered, 1. Create new set: make-bcache -B /dev/nvme1n1 -C /dev/sda --wipe-bcache 2. Run in /sys/fs/bcache/<uuid>: echo 1 > clear_stats && cat stats_five_minute/cache_bypass_hits I can reproduce the panic and get following dmesg with KASAN enabled, [22613.172742] ================================================================== [22613.172862] BUG: KASAN: null-ptr-deref in sysfs_kf_seq_show+0x117/0x230 [22613.172864] Read of size 8 at addr 0000000000000000 by task cat/6753 [22613.172870] CPU: 1 PID: 6753 Comm: cat Not tainted 5.5.0-rc7-lp151.28.16-default+ #11 [22613.172872] Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 07/29/2019 [22613.172873] Call Trace: [22613.172964] dump_stack+0x8b/0xbb [22613.172968] ? sysfs_kf_seq_show+0x117/0x230 [22613.172970] ? sysfs_kf_seq_show+0x117/0x230 [22613.173031] __kasan_report+0x176/0x192 [22613.173064] ? pr_cont_kernfs_name+0x40/0x60 [22613.173067] ? sysfs_kf_seq_show+0x117/0x230 [22613.173070] kasan_report+0xe/0x20 [22613.173072] sysfs_kf_seq_show+0x117/0x230 [22613.173105] seq_read+0x199/0x6d0 [22613.173110] vfs_read+0xa5/0x1a0 [22613.173113] ksys_read+0x110/0x160 [22613.173115] ? kernel_write+0xb0/0xb0 [22613.173177] do_syscall_64+0x77/0x290 [22613.173238] entry_SYSCALL_64_after_hwframe+0x44/0xa9 [22613.173241] RIP: 0033:0x7fc2c886ac61 [22613.173244] Code: fe ff ff 48 8d 3d c7 a0 09 00 48 83 ec 08 e8 46 03 02 00 66 0f 1f 44 00 00 8b 05 ca fb 2c 00 48 63 ff 85 c0 75 13 31 c0 0f 05 <48> 3d 00 f0 ff ff 77 57 f3 c3 0f 1f 44 00 00 55 53 48 89 d5 48 89 [22613.173245] RSP: 002b:00007ffebe776d68 EFLAGS: 00000246 ORIG_RAX: 0000000000000000 [22613.173248] RAX: ffffffffffffffda RBX: 0000000000020000 RCX: 00007fc2c886ac61 [22613.173249] RDX: 0000000000020000 RSI: 00007fc2c8cca000 RDI: 0000000000000003 [22613.173250] RBP: 0000000000020000 R08: ffffffffffffffff R09: 0000000000000000 [22613.173251] R10: 000000000000038c R11: 0000000000000246 R12: 00007fc2c8cca000 [22613.173253] R13: 0000000000000003 R14: 00007fc2c8cca00f R15: 0000000000020000 [22613.173255] ================================================================== [22613.173256] Disabling lock debugging due to kernel taint [22613.173350] BUG: kernel NULL pointer dereference, address: 0000000000000000 [22613.178380] #PF: supervisor read access in kernel mode [22613.180959] #PF: error_code(0x0000) - not-present page [22613.183444] PGD 0 P4D 0 [22613.184867] Oops: 0000 [#1] SMP KASAN PTI [22613.186797] CPU: 1 PID: 6753 Comm: cat Tainted: G B 5.5.0-rc7-lp151.28.16-default+ #11 [22613.191253] Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 07/29/2019 [22613.196706] RIP: 0010:sysfs_kf_seq_show+0x117/0x230 [22613.199097] Code: ff 48 8b 0b 48 8b 44 24 08 48 01 e9 eb a6 31 f6 48 89 cf ba 00 10 00 00 48 89 4c 24 10 e8 b1 e6 e9 ff 4c 89 ff e8 19 07 ea ff <49> 8b 07 48 85 c0 48 89 44 24 08 0f 84 91 00 00 00 49 8b 6d 00 48 [22613.208016] RSP: 0018:ffff8881d4f8fd78 EFLAGS: 00010246 [22613.210448] RAX: 0000000000000000 RBX: ffff8881eb99b180 RCX: ffffffff810d9ef6 [22613.213691] RDX: 0000000000000001 RSI: 0000000000000246 RDI: 0000000000000246 [22613.216893] RBP: 0000000000001000 R08: fffffbfff072ddcd R09: fffffbfff072ddcd [22613.220075] R10: 0000000000000001 R11: fffffbfff072ddcc R12: ffff8881de5c0200 [22613.223256] R13: ffff8881ed175500 R14: ffff8881eb99b198 R15: 0000000000000000 [22613.226290] FS: 00007fc2c8d3d500(0000) GS:ffff8881f2a80000(0000) knlGS:0000000000000000 [22613.229637] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [22613.231993] CR2: 0000000000000000 CR3: 00000001ec89a004 CR4: 00000000003606e0 [22613.234909] Call Trace: [22613.235931] seq_read+0x199/0x6d0 [22613.237259] vfs_read+0xa5/0x1a0 [22613.239229] ksys_read+0x110/0x160 [22613.240590] ? kernel_write+0xb0/0xb0 [22613.242040] do_syscall_64+0x77/0x290 [22613.243625] entry_SYSCALL_64_after_hwframe+0x44/0xa9 [22613.245450] RIP: 0033:0x7fc2c886ac61 [22613.246706] Code: fe ff ff 48 8d 3d c7 a0 09 00 48 83 ec 08 e8 46 03 02 00 66 0f 1f 44 00 00 8b 05 ca fb 2c 00 48 63 ff 85 c0 75 13 31 c0 0f 05 <48> 3d 00 f0 ff ff 77 57 f3 c3 0f 1f 44 00 00 55 53 48 89 d5 48 89 [22613.253296] RSP: 002b:00007ffebe776d68 EFLAGS: 00000246 ORIG_RAX: 0000000000000000 [22613.255835] RAX: ffffffffffffffda RBX: 0000000000020000 RCX: 00007fc2c886ac61 [22613.258472] RDX: 0000000000020000 RSI: 00007fc2c8cca000 RDI: 0000000000000003 [22613.260807] RBP: 0000000000020000 R08: ffffffffffffffff R09: 0000000000000000 [22613.263188] R10: 000000000000038c R11: 0000000000000246 R12: 00007fc2c8cca000 [22613.265598] R13: 0000000000000003 R14: 00007fc2c8cca00f R15: 0000000000020000 [22613.268729] Modules linked in: scsi_transport_iscsi af_packet iscsi_ibft iscsi_boot_sysfs vmw_vsock_vmci_transport vsock fuse bnep kvm_intel kvm irqbypass crc32_pclmul crc32c_intel ghash_clmulni_intel snd_ens1371 snd_ac97_codec ac97_bus bcache snd_pcm btusb btrtl btbcm btintel crc64 aesni_intel glue_helper crypto_simd vmw_balloon cryptd bluetooth snd_timer snd_rawmidi snd joydev pcspkr e1000 rfkill vmw_vmci soundcore ecdh_generic ecc gameport i2c_piix4 mptctl ac button hid_generic usbhid sr_mod cdrom ata_generic ehci_pci vmwgfx uhci_hcd drm_kms_helper syscopyarea serio_raw sysfillrect sysimgblt fb_sys_fops ttm ehci_hcd mptspi scsi_transport_spi mptscsih ata_piix mptbase ahci usbcore libahci drm sg dm_multipath dm_mod scsi_dh_rdac scsi_dh_emc scsi_dh_alua [22613.292429] CR2: 0000000000000000 [22613.293563] ---[ end trace a074b26a8508f378 ]--- [22613.295138] RIP: 0010:sysfs_kf_seq_show+0x117/0x230 [22613.296769] Code: ff 48 8b 0b 48 8b 44 24 08 48 01 e9 eb a6 31 f6 48 89 cf ba 00 10 00 00 48 89 4c 24 10 e8 b1 e6 e9 ff 4c 89 ff e8 19 07 ea ff <49> 8b 07 48 85 c0 48 89 44 24 08 0f 84 91 00 00 00 49 8b 6d 00 48 [22613.303553] RSP: 0018:ffff8881d4f8fd78 EFLAGS: 00010246 [22613.305280] RAX: 0000000000000000 RBX: ffff8881eb99b180 RCX: ffffffff810d9ef6 [22613.307924] RDX: 0000000000000001 RSI: 0000000000000246 RDI: 0000000000000246 [22613.310272] RBP: 0000000000001000 R08: fffffbfff072ddcd R09: fffffbfff072ddcd [22613.312685] R10: 0000000000000001 R11: fffffbfff072ddcc R12: ffff8881de5c0200 [22613.315076] R13: ffff8881ed175500 R14: ffff8881eb99b198 R15: 0000000000000000 [22613.318116] FS: 00007fc2c8d3d500(0000) GS:ffff8881f2a80000(0000) knlGS:0000000000000000 [22613.320743] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [22613.322628] CR2: 0000000000000000 CR3: 00000001ec89a004 CR4: 00000000003606e0 Here this patch fixes the following problem by explicity set all the 7 members to 0 in bch_cache_accounting_clear(). Reported-by: Сорокин Артем Сергеевич <[email protected]> Signed-off-by: Coly Li <[email protected]> Signed-off-by: Jens Axboe <[email protected]>
Powered by cgit, Gruvboxed by Blaster4385.