aboutsummaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)AuthorFilesLines
2012-04-05Merge branch 'for-3.4/fixes-for-rc2' of ↵Olof Johansson1-15/+44
git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into fixes * 'for-3.4/fixes-for-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra: gpio: tegra: Iterate over the correct number of banks gpio: tegra: fix register address calculations for Tegra30
2012-04-05ACPI processor: Use safe_halt() rather than halt() in acpi_idle_play_dead()Luck, Tony1-1/+1
ACPI code is shared by arch/x86 and arch/ia64. ia64 doesn't provide a plain "halt()" function. Use safe_halt() instead. Signed-off-by: Tony Luck <[email protected]> Tested-by: Boris Ostrovsky <[email protected]> Signed-off-by: Len Brown <[email protected]>
2012-04-05drm/exynos: add format list of planeSeung-Woo Kim1-0/+4
NV12, NV12M and NV12MT are added to format list of plane to use these formats for hdmi vp layer. Signed-off-by: Seung-Woo Kim <[email protected]> Signed-off-by: Inki Dae <[email protected]> Signed-off-by: Kyungmin Park <[email protected]>
2012-04-04mlx4: allocate just enough pages instead of always 4 pagesThadeu Lima de Souza Cascardo1-2/+3
The driver uses a 2-order allocation, which is too much on architectures like ppc64, which has a 64KiB page. This particular allocation is used for large packet fragments that may have a size of 512, 1024, 4096 or fill the whole allocation. So, a minimum size of 16384 is good enough and will be the same size that is used in architectures of 4KiB sized pages. This will avoid allocation failures that we see when the system is under stress, but still has plenty of memory, like the one below. This will also allow us to set the interface MTU to higher values like 9000, which was not possible on ppc64 without this patch. Node 1 DMA: 737*64kB 37*128kB 0*256kB 0*512kB 0*1024kB 0*2048kB 0*4096kB 0*8192kB 0*16384kB = 51904kB 83137 total pagecache pages 0 pages in swap cache Swap cache stats: add 0, delete 0, find 0/0 Free swap = 10420096kB Total swap = 10420096kB 107776 pages RAM 1184 pages reserved 147343 pages shared 28152 pages non-shared netstat: page allocation failure. order:2, mode:0x4020 Call Trace: [c0000001a4fa3770] [c000000000012f04] .show_stack+0x74/0x1c0 (unreliable) [c0000001a4fa3820] [c00000000016af38] .__alloc_pages_nodemask+0x618/0x930 [c0000001a4fa39a0] [c0000000001a71a0] .alloc_pages_current+0xb0/0x170 [c0000001a4fa3a40] [d00000000dcc3e00] .mlx4_en_alloc_frag+0x200/0x240 [mlx4_en] [c0000001a4fa3b10] [d00000000dcc3f8c] .mlx4_en_complete_rx_desc+0x14c/0x250 [mlx4_en] [c0000001a4fa3be0] [d00000000dcc4eec] .mlx4_en_process_rx_cq+0x62c/0x850 [mlx4_en] [c0000001a4fa3d20] [d00000000dcc5150] .mlx4_en_poll_rx_cq+0x40/0x90 [mlx4_en] [c0000001a4fa3dc0] [c0000000004e2bb8] .net_rx_action+0x178/0x450 [c0000001a4fa3eb0] [c00000000009c9b8] .__do_softirq+0x118/0x290 [c0000001a4fa3f90] [c000000000031df8] .call_do_softirq+0x14/0x24 [c000000184c3b520] [c00000000000e700] .do_softirq+0xf0/0x110 [c000000184c3b5c0] [c00000000009c6d4] .irq_exit+0xb4/0xc0 [c000000184c3b640] [c00000000000e964] .do_IRQ+0x144/0x230 Signed-off-by: Thadeu Lima de Souza Cascardo <[email protected]> Signed-off-by: Kleber Sacilotto de Souza <[email protected]> Tested-by: Kleber Sacilotto de Souza <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2012-04-04Merge tag 'for_linus-3.4-rc2' of ↵Linus Torvalds1-45/+115
git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb Pull KGDB/KDB regression fixes from Jason Wessel: - Fix a Smatch warning that appeared in the 3.4 merge window - Fix kgdb test suite with SMP for all archs without HW single stepping - Fix kgdb sw breakpoints with CONFIG_DEBUG_RODATA=y limitations on x86 - Fix oops on kgdb test suite with CONFIG_DEBUG_RODATA - Fix kgdb test suite with SMP for all archs with HW single stepping * tag 'for_linus-3.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb: x86,kgdb: Fix DEBUG_RODATA limitation using text_poke() kgdb,debug_core: pass the breakpoint struct instead of address and memory kgdbts: (2 of 2) fix single step awareness to work correctly with SMP kgdbts: (1 of 2) fix single step awareness to work correctly with SMP kgdbts: Fix kernel oops with CONFIG_DEBUG_RODATA kdb: Fix smatch warning on dbg_io_ops->is_console
2012-04-04Merge branch 'for-linus' of ↵Linus Torvalds3-10/+14
git://git.linaro.org/people/mszyprowski/linux-dma-mapping Pull DMA mapping branch from Marek Szyprowski: "Short summary for the whole series: A few limitations have been identified in the current dma-mapping design and its implementations for various architectures. There exist more than one function for allocating and freeing the buffers: currently these 3 are used dma_{alloc, free}_coherent, dma_{alloc,free}_writecombine, dma_{alloc,free}_noncoherent. For most of the systems these calls are almost equivalent and can be interchanged. For others, especially the truly non-coherent ones (like ARM), the difference can be easily noticed in overall driver performance. Sadly not all architectures provide implementations for all of them, so the drivers might need to be adapted and cannot be easily shared between different architectures. The provided patches unify all these functions and hide the differences under the already existing dma attributes concept. The thread with more references is available here: http://www.spinics.net/lists/linux-sh/msg09777.html These patches are also a prerequisite for unifying DMA-mapping implementation on ARM architecture with the common one provided by dma_map_ops structure and extending it with IOMMU support. More information is available in the following thread: http://thread.gmane.org/gmane.linux.kernel.cross-arch/12819 More works on dma-mapping framework are planned, especially in the area of buffer sharing and managing the shared mappings (together with the recently introduced dma_buf interface: commit d15bd7ee445d "dma-buf: Introduce dma buffer sharing mechanism"). The patches in the current set introduce a new alloc/free methods (with support for memory attributes) in dma_map_ops structure, which will later replace dma_alloc_coherent and dma_alloc_writecombine functions." People finally started piping up with support for merging this, so I'm merging it as the last of the pending stuff from the merge window. Looks like pohmelfs is going to wait for 3.5 and more external support for merging. * 'for-linus' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping: common: DMA-mapping: add NON-CONSISTENT attribute common: DMA-mapping: add WRITE_COMBINE attribute common: dma-mapping: introduce mmap method common: dma-mapping: remove old alloc_coherent and free_coherent methods Hexagon: adapt for dma_map_ops changes Unicore32: adapt for dma_map_ops changes Microblaze: adapt for dma_map_ops changes SH: adapt for dma_map_ops changes Alpha: adapt for dma_map_ops changes SPARC: adapt for dma_map_ops changes PowerPC: adapt for dma_map_ops changes MIPS: adapt for dma_map_ops changes X86 & IA64: adapt for dma_map_ops changes common: dma-mapping: introduce generic alloc() and free() methods
2012-04-04stmmac: re-add IFF_UNICAST_FLT for dwmac1000Marc Kleine-Budde1-2/+4
In commit (bfab27a stmmac: add the experimental PCI support) the IFF_UNICAST_FLT flag has been removed from the stmmac_mac_device_setup() function. This patch re-adds the flag. Signed-off-by: Marc Kleine-Budde <[email protected]> Acked-by: Giuseppe Cavallaro <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2012-04-04bnx2x: Clear MDC/MDIO warning messageYaniv Rosner2-2/+1
This patch clears a warning message of "MDC/MDIO access timeout" which may appear when interface is loaded due to missing clock setting before resetting the LED, and starting periodic function too early. Signed-off-by: Yaniv Rosner <[email protected]> Signed-off-by: Eilon Greenstein <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2012-04-04bnx2x: Fix BCM57711+BCM84823 link issueYaniv Rosner1-2/+2
Fix a link problem on the second port of BCM57711 + BCM84823 boards due to incorrect macro usage. Signed-off-by: Yaniv Rosner <[email protected]> Signed-off-by: Eilon Greenstein <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2012-04-04bnx2x: Clear BCM84833 LED after fan failureYaniv Rosner2-0/+12
Signed-off-by: Yaniv Rosner <[email protected]> Signed-off-by: Eilon Greenstein <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2012-04-04bnx2x: Fix BCM84833 PHY FW version presentationYaniv Rosner1-2/+1
Signed-off-by: Yaniv Rosner <[email protected]> Signed-off-by: Eilon Greenstein <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2012-04-04bnx2x: Fix link issue for BCM8727 boards.Yaniv Rosner1-7/+14
This patch fixes a link problem on BCM57712 + BCM8727 designs in which the TX laser is controller by GPIO, after 1.60.xx drivers were previously loaded. On these designs the TX_LASER is enabled by logic AND between the PHY (through MDIO), and the GPIO. When an old driver is used, it disables the MDIO part, hence the GPIO control had no affect de facto. Signed-off-by: Yaniv Rosner <[email protected]> Signed-off-by: Eilon Greenstein <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2012-04-04bnx2x: Restore 1G LED on BCM57712+BCM8727 designs.Yaniv Rosner1-15/+18
Fix no-LED problem when link speed is 1G on BCM57712 + BCM8727 designs, by removing a logic error checking for a different PHY. Signed-off-by: Yaniv Rosner <[email protected]> Signed-off-by: Eilon Greenstein <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2012-04-04bnx2x: Fix BCM578x0-SFI pre-emphasis settingsYaniv Rosner1-5/+5
Fix 578x0-SFI pre-emphasis settings per HW recommendations to achieve better link strength. Signed-off-by: Yaniv Rosner <[email protected]> Signed-off-by: Eilon Greenstein <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2012-04-04bnx2x: Fix BCM57810-KR AN speed transitionYaniv Rosner1-2/+18
BCM57810-KR link may not come up in 1G after running loopback test, so set the relevant registers to their default values before starting KR autoneg. Signed-off-by: Yaniv Rosner <[email protected]> Signed-off-by: Eilon Greenstein <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2012-04-04bnx2x: Fix BCM57810-KR FCYaniv Rosner2-0/+31
Fix 57810-KR flow-control handling link is achieved via CL37 AN. Signed-off-by: Yaniv Rosner <[email protected]> Signed-off-by: Eilon Greenstein <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2012-04-04bnx2x: PFC fixYaniv Rosner2-1/+18
Fix a problem in which PFC frames are not honored, due to incorrect link attributes synchronization following PMF migration, and verify PFC XON is not stuck from previous link change. Signed-off-by: Yaniv Rosner <[email protected]> Signed-off-by: Eilon Greenstein <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2012-04-04regmap: prevent division by zero in rbtree_showStephen Warren1-1/+7
If there are no nodes in the cache, nodes will be 0, so calculating "registers / nodes" will cause division by zero. Signed-off-by: Stephen Warren <[email protected]> Signed-off-by: Mark Brown <[email protected]> Cc: [email protected]
2012-04-04sky2: copy received packets on inefficient unaligned architecturestephen hemminger1-1/+12
Modified from original patch from Chris. The sky2 driver has to have 8 byte alignment of receive buffer on some chip versions. On architectures which don't support efficient unaligned access this doesn't work very well. The solution is to just copy all received packets which is what the driver already does for small packets. This allows the driver to be used on the Tilera TILEmpower-Gx, since the tile architecture doesn't currently handle kernel unaligned accesses, just userspace. Signed-off-by: Stephen Hemminger <[email protected]> Acked-by: Chris Metcalf <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2012-04-04net/bonding: correctly proxy slave neigh param setup ndo functionShlomo Pongratz1-8/+43
The current implemenation was buggy for slaves who use ndo_neigh_setup, since the networking stack invokes the bonding device ndo entry (from neigh_params_alloc) before any devices are enslaved, and the bonding driver can't further delegate the call at that point in time. As a result when bonding IPoIB devices, the neigh_cleanup hasn't been called. Fix that by deferring the actual call into the slave ndo_neigh_setup from the time the bonding neigh_setup is called. Signed-off-by: Shlomo Pongratz <[email protected]> Signed-off-by: Jay Vosburgh <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2012-04-04net/bonding: emit address change event also in bond_releaseShlomo Pongratz1-0/+3
commit 7d26bb103c4 "bonding: emit event when bonding changes MAC" didn't take care to emit the NETDEV_CHANGEADDR event in bond_release, where bonding actually changes the mac address (to all zeroes). As a result the neighbours aren't deleted by the core networking code (which does so upon getting that event). Signed-off-by: Shlomo Pongratz <[email protected]> Signed-off-by: Jay Vosburgh <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2012-04-04Merge tag 'pm-for-3.4-part-2' of ↵Linus Torvalds2-101/+110
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm Pull more power management updates from Rafael Wysocki: - Patch series that hopefully fixes races between the freezer and request_firmware() and request_firmware_nowait() for good, with two cleanups from Stephen Boyd on top. - Runtime PM fix from Alan Stern preventing tasks from getting stuck indefinitely in the runtime PM wait queue. - Device PM QoS update from MyungJoo Ham introducing a new variant of pm_qos_update_request() allowing the callers to specify a timeout. * tag 'pm-for-3.4-part-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: PM / QoS: add pm_qos_update_request_timeout() API firmware_class: Move request_firmware_nowait() to workqueues firmware_class: Reorganize fw_create_instance() PM / Sleep: Mitigate race between the freezer and request_firmware() PM / Sleep: Move disabling of usermode helpers to the freezer PM / Hibernate: Disable usermode helpers right before freezing tasks firmware_class: Do not warn that system is not ready from async loads firmware_class: Split _request_firmware() into three functions, v2 firmware_class: Rework usermodehelper check PM / Runtime: don't forget to wake up waitqueue on failure
2012-04-04gpio: tegra: Iterate over the correct number of banksStephen Warren1-2/+2
When Tegra30 support was added to the Tegra GPIO driver, a few places which iterated over all banks were not converted to use the variable tegra_gpio_bank_count rather than hard-coding the bank count. Fix this. Signed-off-by: Stephen Warren <[email protected]> Acked-by: Olof Johansson <[email protected]>
2012-04-04gpio: tegra: fix register address calculations for Tegra30Stephen Warren1-13/+42
Tegra20 and Tegra30 share the same register layout within registers, but the addresses of the registers is a little different. Fix the driver to cope with this. Signed-off-by: Stephen Warren <[email protected]> Acked-by: Olof Johansson <[email protected]>
2012-04-04Merge tag 'regmap-3.4' of ↵Linus Torvalds1-1/+1
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap Pull a single regmap fix from Mark Brown: "A simple bug that's been lurking for a while but not terribly visible since a high proportion of chips have no register 0 so the normal failure is that we end up doing a bit of extra I/O." * tag 'regmap-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap: regmap: rbtree: Fix register default look-up in sync
2012-04-04Merge tag 'regulator-3.4' of ↵Linus Torvalds10-44/+49
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator Pull regulator fixes from Mark Brown: "A bunch of smallish fixes that came up during the merge window as things got more testing - even more fixes from Axel, a fix for error handling in more complex systems using -EPROBE_DEFER and a couple of small fixes for the new dummy regulators." * tag 'regulator-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: regulator: Remove non-existent parameter from fixed-helper.c kernel doc regulator: Fix setting new voltage in s5m8767_set_voltage regulator: fix sysfs name collision between dummy and fixed dummy regulator regulator: Fix deadlock on removal of regulators with supplies regulator: Fix comments in include/linux/regulator/machine.h regulator: Only update [LDOx|DCx]_HIB_MODE bits in wm8350_[ldo|dcdc]_set_suspend_disable regulator: Fix setting low power mode for wm831x aldo regulator: Return microamps in wm8350_isink_get_current regulator: wm8350: Fix the logic to choose best current limit setting regulator: wm831x-isink: Fix the logic to choose best current limit setting regulator: wm831x-dcdc: Fix the logic to choose best current limit setting regulator: anatop: patching to device-tree property "reg". regulator: Do proper shift to set correct bit for DC[2|5]_HIB_MODE setting regulator: Fix restoring pmic.dcdcx_hib_mode settings in wm8350_dcdc_set_suspend_enable regulator: Fix unbalanced lock/unlock in mc13892_regulator_probe error path regulator: Fix set and get current limit for wm831x_buckv regulator: tps6586x: Fix list minimal voltage setting for LDO0
2012-04-04EXYNOS: fix dependency for EXYNOS_CPUFREQKukjin Kim1-7/+3
This fixes the CPUFREQ dependency for regarding EXYNOS SoCs such as EXYNOS4210, EXYNOS4X12 and EXYNOS5250. Its cpufreq driver should be built with selection of SoC arch part. Reported-by: Russell King <[email protected]> Acked-by: Dave Jones <[email protected]> Signed-off-by: Kukjin Kim <[email protected]>
2012-04-04Merge branch 'x86-urgent-for-linus' of ↵Linus Torvalds1-36/+0
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull x86 fixes from Ingo Molnar. * 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86, kvm: Call restore_sched_clock_state() only after %gs is initialized x86: Use -mno-avx when available x86: Remove the ancient and deprecated disable_hlt() and enable_hlt() facility x86: Preserve lazy irq disable semantics in fixup_irqs()
2012-04-04USB: ehci-atmel: add needed of.h header fileNicolas Ferre1-0/+1
Compilation error in case of non-DT configuration without this of.h header file. Signed-off-by: Nicolas Ferre <[email protected]> Acked-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]> Acked-by: Alan Stern <[email protected]>
2012-04-04USB: ohci-at91: trivial return code name changeNicolas Ferre1-4/+3
Signed-off-by: Nicolas Ferre <[email protected]> Acked-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]> Acked-by: Alan Stern <[email protected]>
2012-04-04USB: ohci-at91: change maximum number of portsNicolas Ferre1-30/+36
Change number of ports to 3 for newer SoCs. Modify pdata structure and ohci-at91 code that was dealing with ports information and check of port indexes. Several coding style errors have been addresses as the patch was touching affected lines of code and was producing errors while run through checkpatch.pl. Signed-off-by: Nicolas Ferre <[email protected]> Acked-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]> Acked-by: Alan Stern <[email protected]>
2012-04-04USB: ohci-at91: rework and fix initializationNicolas Ferre1-42/+46
The DT information are filled in a pdata structure and then passed on to the usual check code of the probe function. Thus we do not need to redo the gpio checking and irq configuration in the DT-related code. On the other hand, we setup GPIO direction in driver for vbus and overcurrent. It will be useful when moving to pinctrl subsystem. Signed-off-by: Nicolas Ferre <[email protected]> Acked-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]> Acked-by: Alan Stern <[email protected]>
2012-04-04USB: ohci-at91: fix vbus_pin_active_low handlingNicolas Ferre1-2/+2
The information is not properly taken into account for {get|set}_power() functions. Signed-off-by: Nicolas Ferre <[email protected]> Acked-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]> Acked-by: Alan Stern <[email protected]> Cc: stable <[email protected]> [3.2+]
2012-04-04Merge tag 'hwmon-for-linus' of ↵Linus Torvalds8-28/+41
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging Pull hwmon patches from Guenter Roeck: - Fix crash in ad7314 driver - Add support for AMD Trinity CPUs to k10temp driver - Fix __initdata/__initconst mixup in w83627ehf driver - Fix runtime warnings in acpi_power_meter and max6639 drivers - Fix build warnings in adm1031, f75375s, sht15, and gpio-fan drivers * tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: hwmon: (ad7314) Adds missing spi_dev initialization hwmon: (k10temp) Add support for AMD Trinity CPUs hwmon: (w83627ehf) mark const init data with __initconst instead of __initdata hwmon: (acpi_power_meter) fix lockdep spew due to non-static lock class hwmon: (adm1031) Fix compiler warning hwmon: (f75375s) Fix warning message seen in some configurations hwmon: (max6639) Convert to dev_pm_ops hwmon: (sht15) Fix Kconfig dependencies hwmon: (gpio-fan) Fix Kconfig dependencies
2012-04-04Merge tag 'mce-fix-for-3.4' of ↵Linus Torvalds1-4/+2
git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp Pull MCE fixlet from Borislav Petkov: "One fix which makes MCE decoding much more "liberal" wrt families." * tag 'mce-fix-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp: MCE, AMD: Drop too granulary family model checks
2012-04-04Merge tag 'md-3.4-fixes' of git://neil.brown.name/mdLinus Torvalds5-35/+75
Pull assorted md fixes from Neil Brown: - some RAID levels didn't clear up properly if md_integrity_register failed - a 'check' of RAID5/RAID6 doesn't actually read any data since a recent patch - so fix that (and mark for -stable) - a couple of other minor bugs. * tag 'md-3.4-fixes' of git://neil.brown.name/md: md/raid1,raid10: don't compare excess byte during consistency check. md/raid5: Fix a bug about judging if the operation is syncing or replacing md/raid1:Remove unnecessary rcu_dereference(conf->mirrors[i].rdev). md: Avoid OOPS when reshaping raid1 to raid0 md/raid5: fix handling of bad blocks during recovery. md/raid1: If md_integrity_register() failed,run() must free the mem md/raid0: If md_integrity_register() fails, raid0_run() must free the mem. md/linear: If md_integrity_register() fails, linear_run() must free the mem.
2012-04-04Merge branch 'fixes' of git://git.linaro.org/people/rmk/linux-armLinus Torvalds2-2/+2
Pull ARM fixes from Russell King: "Nothing too big here, just small fixes." * 'fixes' of git://git.linaro.org/people/rmk/linux-arm: ARM: fix more fallout from 9f97da78bf (Disintegrate asm/system.h for ARM) ARM: fix bios32.c build warning ARM: 7337/1: ptrace: fix ptrace_read_user for !CONFIG_MMU platforms ARM: fix missing bug.h include in arch/arm/kernel/insn.c ARM: sa11x0: fix build errors from DMA engine API updates
2012-04-04Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparcLinus Torvalds1-2/+2
Pull Sparc fixes from David Miller: "One build regression and one serial probe regression fix on sparc." * git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc: serial/sunzilog: fix keyboard on SUN SPARCstation sparc: pgtable_64: change include order
2012-04-04Revert "nouveau/bios: Fix tracking of BIOS image data"Linus Torvalds1-3/+1
This reverts commit d06221c0617ab6d0bc41c4980cefdd9c8cc9a1c1. It turns out to trigger the "BUG_ON(!PageCompound(page))" in kfree(), apparently because the code ends up trying to free somethng that was never kmalloced in the first place. BenH points out that the patch was untested and wasn't meant to go into the upstream kernel that quickly in the first place. Backtrace: bios_shadow bios_shadow_prom nv_mask init_io bios_shadow nouveau_bios_init NVReadVgaCrtc NVSetOwner nouveau_card_init nouveau_load Reported-by: Meelis Roos <[email protected]> Requested-by: Dave Airlie <[email protected]> Acked-by: Benjamin Herrenschmidt <[email protected]> Cc: Ben Skeggs <[email protected]> Signed-off-by: Linus Torvalds <[email protected]>
2012-04-04MCE, AMD: Drop too granulary family model checksBorislav Petkov1-4/+2
MCA details seldom change inbetween the models of a family so don't be too conservative and enable decoding on everything starting from K8 onwards. Minor adjustments can come in later but most importantly, we have some decoding infrastructure in place for upcoming models by default. Signed-off-by: Borislav Petkov <[email protected]>
2012-04-04serial/sunzilog: fix keyboard on SUN SPARCstationSam Ravnborg1-2/+2
The keyboard on my SUN SPARCstation 5 no longer worked. The culprint was: d4e33fac2408d37f7b52e80ca2a89f9fb482914f ("serial: Kill off NO_IRQ") Fix up logic for no irq / irq so the keyboard works again. Signed-off-by: Sam Ravnborg <[email protected]> Cc: Alan Cox <[email protected]> Cc: Greg Kroah-Hartman <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2012-04-03hwmon: (ad7314) Adds missing spi_dev initializationGraeme Smecher1-0/+1
This driver was recently moved from IIO (where it worked) to hwmon (where it doesn't.) This breakage occured because the hwmon version neglected to correctly initialize a reference to spi_dev in its drvdata. The result is a segfault every time the temperature is queried. Signed-off-by: Graeme Smecher <[email protected]> Cc: [email protected] # 3.2+ Signed-off-by: Guenter Roeck <[email protected]>
2012-04-03r8169: enable napi on resume.Artem Savkov1-0/+3
NAPI is disabled during suspend and needs to be enabled on resume. Without this the driver locks up during resume in rtl_reset_work() trying to disable NAPI again. Signed-off-by: Artem Savkov <[email protected]> Acked-by: Francois Romieu <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2012-04-03bnx2x: correction to firmware interfaceYuval Mintz1-55/+55
Commit 621b4d6 updated the bnx2x driver to a new FW version, but lacked a commit to a header file with changes to the firmware's interface. The missing interface change causes iscsi and fcoe to misbehave with the updated firmware. Signed-off-by: Yuval Mintz <[email protected]> Signed-off-by: Dmitry Kravkov <[email protected]> Signed-off-by: Eilon Greenstein <[email protected]> CC: Michael Chan <[email protected]> CC: Bhanu Prakash Gollapudi <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2012-04-03phy:icplus:fix Auto Power Saving in ip101a_config_init.Srinivas Kandagatla1-1/+2
This patch fixes Auto Power Saving configuration in ip101a_config_init which was broken as there is no phy register write followed after setting IP101A_APS_ON flag. This patch also fixes the return value of ip101a_config_init. Without this patch ip101a_config_init returns 2 which is not an error accroding to IS_ERR and the mac driver will continue accessing 2 as valid pointer to phy_dev resulting in memory fault. Signed-off-by: Srinivas Kandagatla <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2012-04-03Merge branch 'master' of ↵David S. Miller3-84/+112
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net
2012-04-03e1000e: Guarantee descriptor writeback flush success.Matthew Vick1-0/+17
In rare circumstances, a descriptor writeback flush may not work if it arrives on a specific clock cycle as a writeback request is going out. Signed-off-by: Matthew Vick <[email protected]> Tested-by: Aaron Brown <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2012-04-03e1000e: prevent oops when adapter is being closed and reset simultaneouslyBruce Allan2-0/+15
When the adapter is closed while it is simultaneously going through a reset, it can cause a null-pointer dereference when the two different code paths simultaneously cleanup up the Tx/Rx resources. Signed-off-by: Bruce Allan <[email protected]> Tested-by: Aaron Brown <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2012-04-03ixgbe: driver fix for link flapMultanen, Eric W1-84/+80
Fix up code so that changes in DCB settings are detected only when ixgbe_dcbnl_set_all is called. Previously, a series of 'change' commands followed by a call to ixgbe_dcbnl_set_all() would always be handled as a HW change - even if the net change was zero. This patch checks for this case of no actual change and skips going through the HW set process. Without this fix, the link could reset and result in a link flap. The core change in this patch is to check for changes in the ixgbe_copy_dcb_cfg() routine - and return a bitmask of detected changes. The other places where changes were detected previously can be removed. Signed-off-by: Eric Multanen <[email protected]> Tested-by: Ross Brattain <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2012-04-03ppp: Don't stop and restart queue on every TX packetDavid Woodhouse1-5/+9
For every transmitted packet, ppp_start_xmit() will stop the netdev queue and then, if appropriate, restart it. This causes the TX softirq to run, entirely gratuitously. This is "only" a waste of CPU time in the normal case, but it's actively harmful when the PPP device is a TEQL slave — the wakeup will cause the offending device to receive the next TX packet from the TEQL queue, when it *should* have gone to the next slave in the list. We end up seeing large bursts of packets on just *one* slave device, rather than using the full available bandwidth over all slaves. This patch fixes the problem by *not* unconditionally stopping the queue in ppp_start_xmit(). It adds a return value from ppp_xmit_process() which indicates whether the queue should be stopped or not. It *doesn't* remove the call to netif_wake_queue() from ppp_xmit_process(), because other code paths (especially from ppp_output_wakeup()) need it there and it's messy to push it out to the other callers to do it based on the return value. So we leave it in place — it's a no-op in the case where the queue wasn't stopped, so it's harmless in the TX path. Signed-off-by: David Woodhouse <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Powered by cgit, Gruvboxed by Blaster4385.