| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
We all know they are redundant.
Reviewed-by: Michal Swiatkowski <[email protected]>
Reviewed-by: Michal Wilczynski <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Signed-off-by: Przemek Kitszel <[email protected]>
Tested-by: Arpana Arland <[email protected]> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <[email protected]>
|
|
The check for existing VFs was redundant since very
inception of SR-IOV sysfs interface in the kernel,
see commit 1789382a72a5 ("PCI: SRIOV control and status via sysfs").
Reviewed-by: Michal Swiatkowski <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Signed-off-by: Przemek Kitszel <[email protected]>
Tested-by: Rafal Romanowski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Currently ice driver's .ndo_bpf callback brings interface down and up
independently of XDP resources' presence. This is only needed when
either these resources have to be configured or removed. It means that
if one is switching XDP programs on-the-fly with running traffic,
packets will be dropped.
To avoid this, compare early on ice_xdp_setup_prog() state of incoming
bpf_prog pointer vs the bpf_prog pointer that is already assigned to
VSI. Do the swap in case VSI has bpf_prog and incoming one are non-NULL.
Lastly, while at it, put old bpf_prog *after* the update of Rx ring's
bpf_prog pointer. In theory previous code could expose us to a state
where Rx ring's bpf_prog would still be referring to old_prog that got
released with earlier bpf_prog_put().
Signed-off-by: Maciej Fijalkowski <[email protected]>
Acked-by: Toke Høiland-Jørgensen <[email protected]>
Reviewed-by: Alexander Lobakin <[email protected]>
Tested-by: Chandan Kumar Rout <[email protected]> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <[email protected]>
|
|
The ice_sq_send_cmd() function is used to send messages to the control
queues used to communicate with firmware, virtual functions, and even some
hardware.
When sending a control queue message, the driver is designed to
synchronously wait for a response from the queue. Currently it waits
between checks for 100 to 150 microseconds.
Commit f86d6f9c49f6 ("ice: sleep, don't busy-wait, for
ICE_CTL_Q_SQ_CMD_TIMEOUT") did recently change the behavior from an
unnecessary delay into a sleep which is a significant improvement over the
old behavior of polling using udelay.
Because of the nature of PCIe transactions, the hardware won't be informed
about a new message until the write to the tail register posts. This is
only guaranteed to occur at the next register read. In ice_sq_send_cmd(),
this happens at the ice_sq_done() call. Because of this, the driver
essentially forces a minimum of one full wait time regardless of how fast
the response is.
For the hardware-based sideband queue, this is especially slow. It is
expected that the hardware will respond within 2 or 3 microseconds, an
order of magnitude faster than the 100-150 microsecond sleep.
Allow such fast completions to occur without delay by introducing a small 5
microsecond delay first before entering the sleeping timeout loop. Ensure
the tail write has been posted by using ice_flush(hw) first.
While at it, lets also remove the ICE_CTL_Q_SQ_CMD_USEC macro as it
obscures the sleep time in the inner loop. It was likely introduced to
avoid "magic numbers", but in practice sleep and delay values are easier to
read and understand when using actual numbers instead of a named constant.
This change should allow the fast hardware based control queue messages to
complete quickly without delay, while slower firmware queue response times
will sleep while waiting for the response.
Signed-off-by: Jacob Keller <[email protected]>
Reviewed-by: Michal Schmidt <[email protected]>
Tested-by: Pucha Himasekhar Reddy <[email protected]> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Make all possible functions static.
Move iavf_force_wb() up to avoid forward declaration.
Suggested-by: Maciej Fijalkowski <[email protected]>
Reviewed-by: Maciej Fijalkowski <[email protected]>
Signed-off-by: Przemek Kitszel <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Remove iavf_aq_get_rss_lut(), iavf_aq_get_rss_key(), iavf_vf_reset().
Remove some "OS specific memory free for shared code" wrappers ;)
Signed-off-by: Przemek Kitszel <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Defer removal of current primary MAC until a replacement is successfully
added. Previous implementation would left filter list with no primary MAC.
This was found while reading the code.
The patch takes advantage of the fact that there can only be a single primary
MAC filter at any time ([1] by Piotr)
Piotr has also applied some review suggestions during our internal patch
submittal process.
[1] https://lore.kernel.org/netdev/[email protected]/
Reviewed-by: Michal Swiatkowski <[email protected]>
Tested-by: Rafal Romanowski <[email protected]>
Signed-off-by: Piotr Gardocki <[email protected]>
Signed-off-by: Przemek Kitszel <[email protected]>
Reviewed-by: Maciej Fijalkowski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
The Dell Studio 1569 predates Windows 8, so it defaults to using
acpi_video# for backlight control, but this is non functional on
this model.
Add a DMI quirk to use the native intel_backlight interface which
does work properly.
Reported-by: raycekarneal <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
https://git.linaro.org/people/jens.wiklander/linux-tee into soc/drivers
Use kmemdup() in OP-TEE driver
* tag 'optee-use-kmemdup-for-6.5' of https://git.linaro.org/people/jens.wiklander/linux-tee:
tee: optee: Use kmemdup() to replace kmalloc + memcpy
Link: https://lore.kernel.org/r/20230615130049.GA979203@rayden
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl into soc/drivers
Memory controller drivers for v6.5
1. Renesas RPC IF: correct the Strobe Timing Adjustment.
2. Broadcom DPFE: fix smatch warning for testing array offset after use.
3. Atmel SDRAMC: drop driver because it was just a wrapper over enabling
clock which is not handled by its clock controller.
4. Minor bindings cleanup.
* tag 'memory-controller-drv-6.5' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl:
dt-bindings: memory-controllers: drop unneeded quotes
memory: atmel-sdramc: remove the driver
memory: brcmstb_dpfe: fix testing array offset after use
memory: renesas-rpc-if: Fix PHYCNT.STRTIM setting
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into soc/drivers
Arm SCMI updates for v6.5
Couple of main additions :-
1. Support for multiple SMC/HVC transports for SCMI:
Some platforms need to support multiple SCMI instances within
a platform(more commonly in a VM). The same SMC/HVC FID is used with
all the instances. The platform or the hypervisor needs a way to
distinguish among SMC/HVC calls made from different instances.
This change adds support for passing shmem channel address as the
parameters in the SMC/HVC call. The address is split into 4KB-page
and offset for simiplicity.
2. Addition od SCMI v3.2 explicit powercap enable/disable support:
SCMI v3.2 specification introduces support to disable powercapping
as a whole on the desired zones.
This change adds the needed support to the core SCMI powercap protocol,
exposing enable/disable protocol operations and then wiring up the new
operartions in the related powercap framework helpers.
* tag 'scmi-updates-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
powercap: arm_scmi: Add support for disabling powercaps on a zone
firmware: arm_scmi: Add Powercap protocol enable support
firmware: arm_scmi: Refactor the internal powercap get/set helpers
firmware: arm_scmi: Augment SMC/HVC to allow optional parameters
dt-bindings: firmware: arm,scmi: support for parameter in smc/hvc call
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into soc/drivers
An addition to the rk3588 power-domains, some new syscon compatibles for
rk3588-based "General-register-files" register areas and a move to
C99 array inits for the dtpm driver to fix sparse warnings.
* tag 'v6.5-rockchip-drivers1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
soc: rockchip: dtpm: use C99 array init syntax
dt-bindings: soc: rockchip: add rk3588 pipe-phy syscon
dt-bindings: soc: rockchip: add rk3588 usb2phy syscon
soc: rockchip: power-domain: add rk3588 mem module support
Link: https://lore.kernel.org/r/10286366.nUPlyArG6x@phil
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
There's an hardware issue that can cause missing timestamps. The bug
is that the interrupt is only cleared if the IGC_TXSTMPH_0 register is
read.
The bug can cause a race condition if a timestamp is captured at the
wrong time, and we will miss that timestamp. To reduce the time window
that the problem is able to happen, in case no timestamp was ready, we
read the "previous" value of the timestamp registers, and we compare
with the "current" one, if it didn't change we can be reasonably sure
that no timestamp was captured. If they are different, we use the new
value as the captured timestamp.
The HW bug is not easy to reproduce, got to reproduce it when smashing
the NIC with timestamping requests from multiple applications (e.g.
multiple ntpperf instances + ptp4l), after 10s of minutes.
This workaround has more impact when multiple timestamp registers are
used, and the IGC_TXSTMPH_0 register always need to be read, so the
interrupt is cleared.
Fixes: 2c344ae24501 ("igc: Add support for TX timestamping")
Signed-off-by: Vinicius Costa Gomes <[email protected]>
Tested-by: Naama Meir <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
When the interrupt is handled, the TXTT_0 bit in the TSYNCTXCTL
register should already be set and the timestamp value already loaded
in the appropriate register.
This simplifies the handling, and reduces the latency for retrieving
the TX timestamp, which increase the amount of TX timestamps that can
be handled in a given time period.
As the "work" function doesn't run in a workqueue anymore, rename it
to something more sensible, a event handler.
Using ntpperf[1] we can see the following performance improvements:
Before:
$ sudo ./ntpperf -i enp3s0 -m 10:22:22:22:22:21 -d 192.168.1.3 -s 172.18.0.0/16 -I -H -o -37
| responses | TX timestamp offset (ns)
rate clients | lost invalid basic xleave | min mean max stddev
1000 100 0.00% 0.00% 0.00% 100.00% -56 +9 +52 19
1500 150 0.00% 0.00% 0.00% 100.00% -40 +30 +75 22
2250 225 0.00% 0.00% 0.00% 100.00% -11 +29 +72 15
3375 337 0.00% 0.00% 0.00% 100.00% -18 +40 +88 22
5062 506 0.00% 0.00% 0.00% 100.00% -19 +23 +77 15
7593 759 0.00% 0.00% 0.00% 100.00% +7 +47 +5168 43
11389 1138 0.00% 0.00% 0.00% 100.00% -11 +41 +5240 39
17083 1708 0.00% 0.00% 0.00% 100.00% +19 +60 +5288 50
25624 2562 0.00% 0.00% 0.00% 100.00% +1 +56 +5368 58
38436 3843 0.00% 0.00% 0.00% 100.00% -84 +12 +8847 66
57654 5765 0.00% 0.00% 100.00% 0.00%
86481 8648 0.00% 0.00% 100.00% 0.00%
129721 12972 0.00% 0.00% 100.00% 0.00%
194581 16384 0.00% 0.00% 100.00% 0.00%
291871 16384 27.35% 0.00% 72.65% 0.00%
437806 16384 50.05% 0.00% 49.95% 0.00%
After:
$ sudo ./ntpperf -i enp3s0 -m 10:22:22:22:22:21 -d 192.168.1.3 -s 172.18.0.0/16 -I -H -o -37
| responses | TX timestamp offset (ns)
rate clients | lost invalid basic xleave | min mean max stddev
1000 100 0.00% 0.00% 0.00% 100.00% -44 +0 +61 19
1500 150 0.00% 0.00% 0.00% 100.00% -6 +39 +81 16
2250 225 0.00% 0.00% 0.00% 100.00% -22 +25 +69 15
3375 337 0.00% 0.00% 0.00% 100.00% -28 +15 +56 14
5062 506 0.00% 0.00% 0.00% 100.00% +7 +78 +143 27
7593 759 0.00% 0.00% 0.00% 100.00% -54 +24 +144 47
11389 1138 0.00% 0.00% 0.00% 100.00% -90 -33 +28 21
17083 1708 0.00% 0.00% 0.00% 100.00% -50 -2 +35 14
25624 2562 0.00% 0.00% 0.00% 100.00% -62 +7 +66 23
38436 3843 0.00% 0.00% 0.00% 100.00% -33 +30 +5395 36
57654 5765 0.00% 0.00% 100.00% 0.00%
86481 8648 0.00% 0.00% 100.00% 0.00%
129721 12972 0.00% 0.00% 100.00% 0.00%
194581 16384 19.50% 0.00% 80.50% 0.00%
291871 16384 35.81% 0.00% 64.19% 0.00%
437806 16384 55.40% 0.00% 44.60% 0.00%
[1] https://github.com/mlichvar/ntpperf
Signed-off-by: Vinicius Costa Gomes <[email protected]>
Reviewed-by: Kurt Kanzenbach <[email protected]>
Tested-by: Naama Meir <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Before requesting a packet transmission to be hardware timestamped,
check if the user has TX timestamping enabled. Fixes an issue that if
a packet was internally forwarded to the NIC, and it had the
SKBTX_HW_TSTAMP flag set, the driver would mark that timestamp as
skipped.
In reality, that timestamp was "not for us", as TX timestamp could
never be enabled in the NIC.
Checking if the TX timestamping is enabled earlier has a secondary
effect that when TX timestamping is disabled, there's no need to check
for timestamp timeouts.
We should only take care to free any pending timestamp when TX
timestamping is disabled, as that skb would never be released
otherwise.
Fixes: 2c344ae24501 ("igc: Add support for TX timestamping")
Suggested-by: Vladimir Oltean <[email protected]>
Signed-off-by: Vinicius Costa Gomes <[email protected]>
Tested-by: Naama Meir <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Currently, the igc driver supports timestamping only one tx packet at a
time. During the transmission flow, the skb that requires hardware
timestamping is saved in adapter->ptp_tx_skb. Once hardware has the
timestamp, an interrupt is delivered, and adapter->ptp_tx_work is
scheduled. In igc_ptp_tx_work(), we read the timestamp register, update
adapter->ptp_tx_skb, and notify the network stack.
While the thread executing the transmission flow (the user process
running in kernel mode) and the thread executing ptp_tx_work don't
access adapter->ptp_tx_skb concurrently, there are two other places
where adapter->ptp_tx_skb is accessed: igc_ptp_tx_hang() and
igc_ptp_suspend().
igc_ptp_tx_hang() is executed by the adapter->watchdog_task worker
thread which runs periodically so it is possible we have two threads
accessing ptp_tx_skb at the same time. Consider the following scenario:
right after __IGC_PTP_TX_IN_PROGRESS is set in igc_xmit_frame_ring(),
igc_ptp_tx_hang() is executed. Since adapter->ptp_tx_start hasn't been
written yet, this is considered a timeout and adapter->ptp_tx_skb is
cleaned up.
This patch fixes the issue described above by adding the ptp_tx_lock to
protect access to ptp_tx_skb and ptp_tx_start fields from igc_adapter.
Since igc_xmit_frame_ring() called in atomic context by the networking
stack, ptp_tx_lock is defined as a spinlock, and the irq safe variants
of lock/unlock are used.
With the introduction of the ptp_tx_lock, the __IGC_PTP_TX_IN_PROGRESS
flag doesn't provide much of a use anymore so this patch gets rid of it.
Fixes: 2c344ae24501 ("igc: Add support for TX timestamping")
Signed-off-by: Andre Guedes <[email protected]>
Signed-off-by: Vinicius Costa Gomes <[email protected]>
Reviewed-by: Kurt Kanzenbach <[email protected]>
Tested-by: Naama Meir <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
For the declaration of parent clocks, use struct clk_parent_data instead
of a string. Due to the change in the passed arguments, replace the usage
of devm_clk_hw_register_mux() with clk_hw_register_mux_parent_data() for
all cases.
Signed-off-by: Jacky Huang <[email protected]>
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
The constant hex values used to define register offsets were written
in uppercase. This patch update all these constant hex values to
be lowercase.
Signed-off-by: Jacky Huang <[email protected]>
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
Moved the declaration of extern functions ma35d1_reg_clk_pll() and
ma35d1_reg_adc_clkdiv() from the .c files to the newly created header
file clk-ma35d1.h.
Signed-off-by: Jacky Huang <[email protected]>
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux into soc/drivers
Amlogic Drivers changes for v6.5:
- tag some powers domains as always-on for secure-pwrc
- fix MAINTAINERS entry for PHY drivers & bindings
- Amlogic Meson GPIO interrupt controller binding to yaml conversion
* tag 'amlogic-drivers-for-v6.5' of https://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux:
dt-bindings: interrupt-controller: Convert Amlogic Meson GPIO interrupt controller binding
MAINTAINERS: add PHY-related files to Amlogic SoC file list
drivers: meson: secure-pwrc: always enable DMA domain
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
This patch fixes a spectre-v1 gadget in cdrom.
The gadget could be triggered by speculatively
bypassing the cdi->capacity check.
Signed-off-by: Jordy Zomer <[email protected]>
Link: https://lore.kernel.org/all/[email protected]
Reviewed-by: Phillip Potter <[email protected]>
Link: https://lore.kernel.org/all/ZI1+1OG9Ut1MqsUC@equinox
Signed-off-by: Phillip Potter <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jens Axboe <[email protected]>
|
|
struct mux_adth actually ends with multiple struct mux_adth_dg members.
This is seen both in the comments about the member:
/**
* struct mux_adth - Structure of the Aggregated Datagram Table Header.
...
* @dg: datagramm table with variable length
*/
and in the preparation for populating it:
adth_dg_size = offsetof(struct mux_adth, dg) +
ul_adb->dg_count[i] * sizeof(*dg);
...
adth_dg_size -= offsetof(struct mux_adth, dg);
memcpy(&adth->dg, ul_adb->dg[i], adth_dg_size);
This was reported as a run-time false positive warning:
memcpy: detected field-spanning write (size 16) of single field "&adth->dg" at drivers/net/wwan/iosm/iosm_ipc_mux_codec.c:852 (size 8)
Adjust the struct mux_adth definition and associated sizeof() math; no binary
output differences are observed in the resulting object file.
Reported-by: Florian Klink <[email protected]>
Closes: https://lore.kernel.org/lkml/[email protected]/
Fixes: 1f52d7b62285 ("net: wwan: iosm: Enable M.2 7360 WWAN card support")
Cc: M Chetan Kumar <[email protected]>
Cc: Bagas Sanjaya <[email protected]>
Cc: Intel Corporation <[email protected]>
Cc: Loic Poulain <[email protected]>
Cc: Sergey Ryazanov <[email protected]>
Cc: Johannes Berg <[email protected]>
Cc: "David S. Miller" <[email protected]>
Cc: Eric Dumazet <[email protected]>
Cc: Jakub Kicinski <[email protected]>
Cc: Paolo Abeni <[email protected]>
Cc: "Gustavo A. R. Silva" <[email protected]>
Cc: [email protected]
Signed-off-by: Kees Cook <[email protected]>
Reviewed-by: Gustavo A. R. Silva <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Paolo Abeni <[email protected]>
|
|
The ux500 variant doesn't have a HW based timeout to use for busy-end IRQs.
To avoid hanging and waiting for the card to stop signaling busy, let's
schedule a delayed work, according to the corresponding cmd->busy_timeout
for the command. If the work gets to run, let's kick the IRQ handler to
complete the currently running request/command.
Reviewed-by: Linus Walleij <[email protected]>
Tested-by: Linus Walleij <[email protected]>
Signed-off-by: Ulf Hansson <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Power source notify handler is getting registered even when none of the
PMF feature in enabled leading to a crash.
...
[ 22.592162] Call Trace:
[ 22.592164] <TASK>
[ 22.592164] ? rcu_note_context_switch+0x5e0/0x660
[ 22.592166] ? __warn+0x81/0x130
[ 22.592171] ? rcu_note_context_switch+0x5e0/0x660
[ 22.592172] ? report_bug+0x171/0x1a0
[ 22.592175] ? prb_read_valid+0x1b/0x30
[ 22.592177] ? handle_bug+0x3c/0x80
[ 22.592178] ? exc_invalid_op+0x17/0x70
[ 22.592179] ? asm_exc_invalid_op+0x1a/0x20
[ 22.592182] ? rcu_note_context_switch+0x5e0/0x660
[ 22.592183] ? acpi_ut_delete_object_desc+0x86/0xb0
[ 22.592186] ? acpi_ut_update_ref_count.part.0+0x22d/0x930
[ 22.592187] __schedule+0xc0/0x1410
[ 22.592189] ? ktime_get+0x3c/0xa0
[ 22.592191] ? lapic_next_event+0x1d/0x30
[ 22.592193] ? hrtimer_start_range_ns+0x25b/0x350
[ 22.592196] schedule+0x5e/0xd0
[ 22.592197] schedule_hrtimeout_range_clock+0xbe/0x140
[ 22.592199] ? __pfx_hrtimer_wakeup+0x10/0x10
[ 22.592200] usleep_range_state+0x64/0x90
[ 22.592203] amd_pmf_send_cmd+0x106/0x2a0 [amd_pmf bddfe0fe3712aaa99acce3d5487405c5213c6616]
[ 22.592207] amd_pmf_update_slider+0x56/0x1b0 [amd_pmf bddfe0fe3712aaa99acce3d5487405c5213c6616]
[ 22.592210] amd_pmf_set_sps_power_limits+0x72/0x80 [amd_pmf bddfe0fe3712aaa99acce3d5487405c5213c6616]
[ 22.592213] amd_pmf_pwr_src_notify_call+0x49/0x90 [amd_pmf bddfe0fe3712aaa99acce3d5487405c5213c6616]
[ 22.592216] notifier_call_chain+0x5a/0xd0
[ 22.592218] atomic_notifier_call_chain+0x32/0x50
...
Fix this by moving the registration of source change notify handler only
when SPS(Static Slider) is advertised as supported.
Reported-by: Allen Zhong <[email protected]>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217571
Fixes: 4c71ae414474 ("platform/x86/amd/pmf: Add support SPS PMF feature")
Tested-by: Patil Rajesh Reddy <[email protected]>
Reviewed-by: Mario Limonciello <[email protected]>
Signed-off-by: Shyam Sundar S K <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Reviewed-by: Hans de Goede <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
|
|
With CONFIG_ARCH_STM32 making it into arch/arm64, a couple of format
strings no longer work, since they rely on size_t being compatible
with %x, or they print an 'int' using %z:
drivers/remoteproc/stm32_rproc.c: In function 'stm32_rproc_mem_alloc':
drivers/remoteproc/stm32_rproc.c:122:22: error: format '%x' expects argument of type 'unsigned int', but argument 5 has type 'size_t' {aka 'long unsigned int'} [-Werror=format=]
drivers/remoteproc/stm32_rproc.c:122:40: note: format string is defined here
122 | dev_dbg(dev, "map memory: %pa+%x\n", &mem->dma, mem->len);
| ~^
| |
| unsigned int
| %lx
drivers/remoteproc/stm32_rproc.c:125:30: error: format '%x' expects argument of type 'unsigned int', but argument 4 has type 'size_t' {aka 'long unsigned int'} [-Werror=format=]
drivers/remoteproc/stm32_rproc.c:125:65: note: format string is defined here
125 | dev_err(dev, "Unable to map memory region: %pa+%x\n",
| ~^
| |
| unsigned int
| %lx
drivers/remoteproc/stm32_rproc.c: In function 'stm32_rproc_get_loaded_rsc_table':
drivers/remoteproc/stm32_rproc.c:646:30: error: format '%zx' expects argument of type 'size_t', but argument 4 has type 'int' [-Werror=format=]
drivers/remoteproc/stm32_rproc.c:646:66: note: format string is defined here
646 | dev_err(dev, "Unable to map memory region: %pa+%zx\n",
| ~~^
| |
| long unsigned int
| %x
Fix up all three instances to work across architectures, and enable
compile testing for this driver to ensure it builds everywhere.
Reviewed-by: Arnaud Pouliquen <[email protected]>
Acked-by: Randy Dunlap <[email protected]>
Tested-by: Randy Dunlap <[email protected]>
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
Use the TX FIFO size read from CAN controller register, instead of using
hard coded value.
Signed-off-by: Jimmy Assarsson <[email protected]>
Reviewed-by: Vincent Mailhol <[email protected]>
Link: https://lore.kernel.org/all/[email protected]
Signed-off-by: Marc Kleine-Budde <[email protected]>
|
|
Refactor code;
- Format code
- Rename variables and macros
- Remove intermediate variables
- Add/remove blank lines
- Reduce scope of variables
- Add helper functions
Signed-off-by: Jimmy Assarsson <[email protected]>
Reviewed-by: Vincent Mailhol <[email protected]>
Link: https://lore.kernel.org/all/[email protected]
Signed-off-by: Marc Kleine-Budde <[email protected]>
|
|
Add support for the Classical CAN raw DLC functionality to send and receive
DLC values from 9 .. 15.
Signed-off-by: Jimmy Assarsson <[email protected]>
Reviewed-by: Vincent Mailhol <[email protected]>
Link: https://lore.kernel.org/all/[email protected]
Signed-off-by: Marc Kleine-Budde <[email protected]>
|
|
Replace opencoded masking and shifting, with GENMASK, FIELD_GET and
FIELD_PREP macros.
Suggested-by: Vincent MAILHOL <[email protected]>
Signed-off-by: Jimmy Assarsson <[email protected]>
Reviewed-by: Vincent Mailhol <[email protected]>
Link: https://lore.kernel.org/all/[email protected]
Signed-off-by: Marc Kleine-Budde <[email protected]>
|
|
Sort the registers defines, in the same order as the register bits/fields
are defined.
Sort register bits/fields in MSB-to-LSB order.
Update and add comments.
Signed-off-by: Jimmy Assarsson <[email protected]>
Reviewed-by: Vincent Mailhol <[email protected]>
Link: https://lore.kernel.org/all/[email protected]
Signed-off-by: Marc Kleine-Budde <[email protected]>
|
|
kvaser_pciefd_{receive,transmit,set_tx}_irq()
Change return type to void for kvaser_pciefd_transmit_irq(),
kvaser_pciefd_receive_irq() and kvaser_pciefd_set_tx_irq().
These functions always return zero.
Signed-off-by: Jimmy Assarsson <[email protected]>
Reviewed-by: Vincent Mailhol <[email protected]>
Link: https://lore.kernel.org/all/[email protected]
Signed-off-by: Marc Kleine-Budde <[email protected]>
|
|
Rename device ID defines to better match the product name of the supported
device.
Use 16 bit hexadecimal values for device IDs.
And format kvaser_pciefd_id_table using clang-format.
Signed-off-by: Jimmy Assarsson <[email protected]>
Reviewed-by: Vincent Mailhol <[email protected]>
Link: https://lore.kernel.org/all/[email protected]
Signed-off-by: Marc Kleine-Budde <[email protected]>
|
|
Sort the includes in alphabetic order.
Signed-off-by: Jimmy Assarsson <[email protected]>
Reviewed-by: Vincent Mailhol <[email protected]>
Link: https://lore.kernel.org/all/[email protected]
Signed-off-by: Marc Kleine-Budde <[email protected]>
|
|
Remove SPI flash parameter read functionality, since it's only used for
reading the interface CAN controller count.
This information is already read from a register, making the information
redundant.
Signed-off-by: Jimmy Assarsson <[email protected]>
Reviewed-by: Vincent Mailhol <[email protected]>
Link: https://lore.kernel.org/all/[email protected]
Signed-off-by: Marc Kleine-Budde <[email protected]>
|
|
Define unsigned constants with type suffix 'U'
Signed-off-by: Jimmy Assarsson <[email protected]>
Reviewed-by: Vincent Mailhol <[email protected]>
Link: https://lore.kernel.org/all/[email protected]
Signed-off-by: Marc Kleine-Budde <[email protected]>
|
|
Set hardware timestamp on transmitted packets.
Fixes: 26ad340e582d ("can: kvaser_pciefd: Add driver for Kvaser PCIEcan devices")
Signed-off-by: Jimmy Assarsson <[email protected]>
Reviewed-by: Vincent Mailhol <[email protected]>
Link: https://lore.kernel.org/all/[email protected]
Signed-off-by: Marc Kleine-Budde <[email protected]>
|
|
Add new function, kvaser_pciefd_set_skb_timestamp(), to set skb hwtstamps.
Signed-off-by: Jimmy Assarsson <[email protected]>
Reviewed-by: Vincent Mailhol <[email protected]>
Link: https://lore.kernel.org/all/[email protected]
Signed-off-by: Marc Kleine-Budde <[email protected]>
|
|
The Kvaser KCAN controller got a feature to send error frames on request.
The packet KVASER_PCIEFD_PACK_TYPE_EFRAME_ACK signals that the requested
error frame was transmitted.
Since this feature is not supported by the driver, drop the handler and add
KVASER_PCIEFD_PACK_TYPE_EFRAME_ACK to the list of unexpected packet types.
Fixes: 26ad340e582d ("can: kvaser_pciefd: Add driver for Kvaser PCIEcan devices")
Signed-off-by: Jimmy Assarsson <[email protected]>
Reviewed-by: Vincent Mailhol <[email protected]>
Link: https://lore.kernel.org/all/[email protected]
Signed-off-by: Marc Kleine-Budde <[email protected]>
|
|
The PCI interrupt register, KVASER_PCIEFD_IRQ_REG, is level triggered.
Writing to the register doesn't affect it.
Fixes: 26ad340e582d ("can: kvaser_pciefd: Add driver for Kvaser PCIEcan devices")
Signed-off-by: Jimmy Assarsson <[email protected]>
Reviewed-by: Vincent Mailhol <[email protected]>
Link: https://lore.kernel.org/all/[email protected]
Signed-off-by: Marc Kleine-Budde <[email protected]>
|
|
Introduce a method to calculate the exact size in bits of a CAN(-FD)
frame with or without dynamic bitstuffing.
These are all the possible combinations taken into account:
- Classical CAN or CAN-FD
- Standard or Extended frame format
- CAN-FD CRC17 or CRC21
- Include or not intermission
Instead of doing several individual macro definitions, declare the
can_frame_bits() function-like macro. To this extent, do a full
refactoring of the length definitions.
In addition add the can_frame_bytes(). This function-like macro
replaces the existing macro:
- CAN_FRAME_OVERHEAD_SFF: can_frame_bytes(false, false, 0)
- CAN_FRAME_OVERHEAD_EFF: can_frame_bytes(false, true, 0)
- CANFD_FRAME_OVERHEAD_SFF: can_frame_bytes(true, false, 0)
- CANFD_FRAME_OVERHEAD_EFF: can_frame_bytes(true, true, 0)
Function-like macros were chosen over inline functions because they
can be used to initialize const struct fields.
The different maximum frame lengths (maximum data length, including
intermission) are as follow:
Frame type bits bytes
-------------------------------------------------------
Classic CAN SFF no bitstuffing 111 14
Classic CAN EFF no bitstuffing 131 17
Classic CAN SFF bitstuffing 135 17
Classic CAN EFF bitstuffing 160 20
CAN-FD SFF no bitstuffing 579 73
CAN-FD EFF no bitstuffing 598 75
CAN-FD SFF bitstuffing 712 89
CAN-FD EFF bitstuffing 736 92
The macro CAN_FRAME_LEN_MAX and CANFD_FRAME_LEN_MAX are kept as an
alias to, respectively, can_frame_bytes(false, true, CAN_MAX_DLEN) and
can_frame_bytes(true, true, CANFD_MAX_DLEN).
In addition to the above:
- Use ISO 11898-1:2015 definitions for the names of the CAN frame
fields.
- Include linux/bits.h for use of BITS_PER_BYTE.
- Include linux/math.h for use of mult_frac() and
DIV_ROUND_UP(). N.B: the use of DIV_ROUND_UP() is not new to this
patch, but the include was previously omitted.
- Add copyright 2023 for myself.
Suggested-by: Thomas Kopp <[email protected]>
Signed-off-by: Vincent Mailhol <[email protected]>
Reviewed-by: Thomas Kopp <[email protected]>
Link: https://lore.kernel.org/all/[email protected]
Signed-off-by: Marc Kleine-Budde <[email protected]>
|
|
This patch aligns code to match open parenthesis.
Link: https://lore.kernel.org/all/[email protected]
Signed-off-by: Marc Kleine-Budde <[email protected]>
|
|
This patch aligns code to match open parenthesis.
Link: https://lore.kernel.org/all/[email protected]
Signed-off-by: Marc Kleine-Budde <[email protected]>
|
|
This patch aligns code to match open parenthesis and removes a
trailing whitespace.
Fixes: eb38c2053b67 ("can: rx-offload: rename can_rx_offload_queue_sorted() -> can_rx_offload_queue_timestamp()")
Fixes: f5071d9e729d ("can: m_can: m_can_handle_bus_errors(): add support for handling DLEC error on CAN-FD frames")
Reported-by: Judith Mendez <[email protected]>
Link: https://lore.kernel.org/all/[email protected]
Signed-off-by: Marc Kleine-Budde <[email protected]>
|
|
In their RZN1 SoC, Renesas put a CAN controller supposed to act very
similarly to the original Philips sja1000. In practice, while flooding
the bus with another device, we discovered that the controller very
often after an overrun situation would just refuse any new frame, drop
them all and trigger over and over again the overrun interrupt, even
though the buffer would have been totally emptied. The controller acts
like if its internal buffer offsets (where it writes and where the host
reads) where totally screwed-up.
Renesas manual mentions a single action to perform in order to
resynchronize the read and write offsets within the buffer: performing
a soft reset.
Performing a soft reset takes a bit of time and involves small delays,
so better do that in a threaded handler rather than inside the hard IRQ
handler.
Add platform data to recognize the platforms which need this workaround,
and when the faulty situation is diagnosed, stop what is being
performed and request the threaded handler to be executed in order to
perform the reset.
Tested-by: Jérémie Dautheribes <[email protected]> # 5.10
Signed-off-by: Miquel Raynal <[email protected]>
Link: https://lore.kernel.org/all/[email protected]
Signed-off-by: Marc Kleine-Budde <[email protected]>
|
|
In order to support a flavor of the sja1000 which sometimes freezes, it
will be needed upon certain interrupts to perform a soft reset. The soft
reset operation takes a bit of time, so better not do it within the hard
interrupt handler but rather in a threaded handler. Let's prepare the
possibility for sja1000_err() to request "interrupting" the current flow
and request the threaded handler to be run while keeping the interrupt
line low.
There is no functional change.
Signed-off-by: Miquel Raynal <[email protected]>
Link: https://lore.kernel.org/all/[email protected]
Signed-off-by: Marc Kleine-Budde <[email protected]>
|
|
Rename the following macros:
- ESD_RTR to ESD_USB_RTR
- ESD_EV_CAN_ERROR_EXT to ESD_USB_EV_CAN_ERROR_EXT
Additionally remove the double newline trailing to definition
of ESD_USB_RTR.
Signed-off-by: Frank Jungclaus <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Marc Kleine-Budde <[email protected]>
|
|
Make use of kernel macros BIT() and GENMASK().
Signed-off-by: Frank Jungclaus <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Marc Kleine-Budde <[email protected]>
|
|
Replace a netdev_info(), emitting an informational message about the
BTR value to be send to the controller, with a debug message by means
of netdev_dbg().
Link: https://lore.kernel.org/all/[email protected]/
Suggested-by: Marc Kleine-Budde <[email protected]>
Suggested-by: Vincent MAILHOL <[email protected]>
Signed-off-by: Frank Jungclaus <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Marc Kleine-Budde <[email protected]>
|
|
Replace all hardcoded values supplied to the len element of
esd_usb_msg (and its siblings) by more readable expressions, based on
sizeof(), offsetof(), etc.
Also spend documentation / comments that the len element of esd_usb_msg
is in multiples of 32bit words and not in bytes.
Link: https://lore.kernel.org/all/CAMZ6RqLaDNy-fZ2G0+QMhUEckkXLL+ZyELVSDFmqpd++aBzZQg@mail.gmail.com/
Suggested-by: Vincent MAILHOL <[email protected]>
Signed-off-by: Frank Jungclaus <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Marc Kleine-Budde <[email protected]>
|
|
Prefix all the structures with the device name.
For commonly used structures make use of (the module name) esd_usb_.
For esd CAN-USB/2 and CAN-USB/Micro specific structures use
esd_usb_2_ and esd_usb_m.
Link: https://lore.kernel.org/all/CAMZ6RqLaDNy-fZ2G0+QMhUEckkXLL+ZyELVSDFmqpd++aBzZQg@mail.gmail.com/
Suggested-by: Vincent MAILHOL <[email protected]>
Signed-off-by: Frank Jungclaus <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Marc Kleine-Budde <[email protected]>
|