| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Anatoly reports that he gets the below warning when booting -git on
a sparc64 box on debian unstable:
...
[ 13.352975] aes_sparc64: Using sparc64 aes opcodes optimized AES
implementation
[ 13.428002] ------------[ cut here ]------------
[ 13.428081] WARNING: CPU: 21 PID: 586 at
drivers/block/pktcdvd.c:2597 pkt_setup_dev+0x2e4/0x5a0 [pktcdvd]
[ 13.428147] Attempt to register a non-SCSI queue
[ 13.428184] Modules linked in: pktcdvd libdes cdrom aes_sparc64
n2_rng md5_sparc64 sha512_sparc64 rng_core sha256_sparc64 flash
sha1_sparc64 ip_tables x_tables ipv6 crc_ccitt nf_defrag_ipv6 autofs4
ext4 crc16 mbcache jbd2 raid10 raid456 async_raid6_recov async_memcpy
async_pq async_xor xor async_tx raid6_pq raid1 raid0 multipath linear
md_mod crc32c_sparc64
[ 13.428452] CPU: 21 PID: 586 Comm: pktsetup Not tainted
5.3.0-10169-g574cc4539762 #1234
[ 13.428507] Call Trace:
[ 13.428542] [00000000004635c0] __warn+0xc0/0x100
[ 13.428582] [0000000000463634] warn_slowpath_fmt+0x34/0x60
[ 13.428626] [000000001045b244] pkt_setup_dev+0x2e4/0x5a0 [pktcdvd]
[ 13.428674] [000000001045ccf4] pkt_ctl_ioctl+0x94/0x220 [pktcdvd]
[ 13.428724] [00000000006b95c8] do_vfs_ioctl+0x628/0x6e0
[ 13.428764] [00000000006b96c8] ksys_ioctl+0x48/0x80
[ 13.428803] [00000000006b9714] sys_ioctl+0x14/0x40
[ 13.428847] [0000000000406294] linux_sparc_syscall+0x34/0x44
[ 13.428890] irq event stamp: 4181
[ 13.428924] hardirqs last enabled at (4189): [<00000000004e0a74>]
console_unlock+0x634/0x6c0
[ 13.428984] hardirqs last disabled at (4196): [<00000000004e0540>]
console_unlock+0x100/0x6c0
[ 13.429048] softirqs last enabled at (3978): [<0000000000b2e2d8>]
__do_softirq+0x498/0x520
[ 13.429110] softirqs last disabled at (3967): [<000000000042cfb4>]
do_softirq_own_stack+0x34/0x60
[ 13.429172] ---[ end trace 2220ca468f32967d ]---
[ 13.430018] pktcdvd: setup of pktcdvd device failed
[ 13.455589] des_sparc64: Using sparc64 des opcodes optimized DES
implementation
[ 13.515334] camellia_sparc64: Using sparc64 camellia opcodes
optimized CAMELLIA implementation
[ 13.522856] pktcdvd: setup of pktcdvd device failed
[ 13.529327] pktcdvd: setup of pktcdvd device failed
[ 13.532932] pktcdvd: setup of pktcdvd device failed
[ 13.536165] pktcdvd: setup of pktcdvd device failed
[ 13.539372] pktcdvd: setup of pktcdvd device failed
[ 13.542834] pktcdvd: setup of pktcdvd device failed
[ 13.546536] pktcdvd: setup of pktcdvd device failed
[ 15.431071] XFS (dm-0): Mounting V5 Filesystem
...
Apparently debian auto-attaches any cdrom like device to pktcdvd, which
can lead to the above warning. There's really no reason to warn for this
situation, kill it.
Reported-by: Anatoly Pugachev <[email protected]>
Signed-off-by: Jens Axboe <[email protected]>
|
|
Use 'skb_put_data()' instead of rewritting it.
This improves readability.
Signed-off-by: Christophe JAILLET <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Putting a struct stmmac_rss object on the stack is a bad idea,
as it exceeds the warning limit for a stack frame on 32-bit architectures:
drivers/net/ethernet/stmicro/stmmac/stmmac_selftests.c:1221:12: error: stack frame size of 1208 bytes in function '__stmmac_test_l3filt' [-Werror,-Wframe-larger-than=]
drivers/net/ethernet/stmicro/stmmac/stmmac_selftests.c:1338:12: error: stack frame size of 1208 bytes in function '__stmmac_test_l4filt' [-Werror,-Wframe-larger-than=]
As the object is the trivial empty case, change the called function
to accept a NULL pointer to mean the same thing and remove the
large variable in the two callers.
Fixes: 4647e021193d ("net: stmmac: selftests: Add selftest for L3/L4 Filters")
Signed-off-by: Arnd Bergmann <[email protected]>
Acked-by: Jose Abreu <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
If CONFIG_NET_DSA_SJA1105_TAS=y and CONFIG_NET_SCH_TAPRIO=n,
below error can be found:
drivers/net/dsa/sja1105/sja1105_tas.o: In function `sja1105_setup_tc_taprio':
sja1105_tas.c:(.text+0x318): undefined reference to `taprio_offload_free'
sja1105_tas.c:(.text+0x590): undefined reference to `taprio_offload_get'
drivers/net/dsa/sja1105/sja1105_tas.o: In function `sja1105_tas_teardown':
sja1105_tas.c:(.text+0x610): undefined reference to `taprio_offload_free'
make: *** [vmlinux] Error 1
sja1105_tas needs tc-taprio, so this patch add the dependency for it.
Fixes: 317ab5b86c8e ("net: dsa: sja1105: Configure the Time-Aware Scheduler via tc-taprio offload")
Signed-off-by: Mao Wenan <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
The ARM netx platform got removed in 5.3, so this driver
is now useless.
Reported-by: Uwe Kleine-König <[email protected]>
Cc: Sascha Hauer <[email protected]>
Signed-off-by: Arnd Bergmann <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
According to the DP83865 datasheet "the 10 Mbps HDX loopback can be
disabled in the expanded memory register 0x1C0.1". The driver erroneously
used bit 0 instead of bit 1.
Fixes: 4621bf129856 ("phy: Add file missed in previous commit.")
Signed-off-by: Peter Mamonov <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Endpoints with zero wMaxPacketSize are not usable for transferring
data. Ignore such endpoints when looking for valid in, out and
status pipes, to make the drivers more robust against invalid and
meaningless descriptors.
The wMaxPacketSize of these endpoints are used for memory allocations
and as divisors in many usbnet minidrivers. Avoiding zero is therefore
critical.
Signed-off-by: Bjørn Mork <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Endpoints with zero wMaxPacketSize are not usable for transferring
data. Ignore such endpoints when looking for valid in, out and
status pipes, to make the driver more robust against invalid and
meaningless descriptors.
The wMaxPacketSize of the out pipe is used as divisor. So this change
fixes a divide-by-zero bug.
Reported-by: [email protected]
Signed-off-by: Bjørn Mork <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs
Pull UBI, UBIFS and JFFS2 updates from Richard Weinberger:
"UBI:
- Be less stupid when placing a fastmap anchor
- Try harder to get an empty PEB in case of contention
- Make ubiblock to warn if image is not a multiple of 512
UBIFS:
- Various fixes in error paths
JFFS2:
- Various fixes in error paths"
* tag 'upstream-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs:
jffs2: Fix memory leak in jffs2_scan_eraseblock() error path
jffs2: Remove jffs2_gc_fetch_page and jffs2_gc_release_page
jffs2: Fix possible null-pointer dereferences in jffs2_add_frag_to_fragtree()
ubi: block: Warn if volume size is not multiple of 512
ubifs: Fix memory leak bug in alloc_ubifs_info() error path
ubifs: Fix memory leak in __ubifs_node_verify_hmac error path
ubifs: Fix memory leak in read_znode() error path
ubi: ubi_wl_get_peb: Increase the number of attempts while getting PEB
ubi: Don't do anchor move within fastmap area
ubifs: Remove redundant assignment to pointer fname
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Richard Weinberger:
"MTD core changes:
- add debugfs nodes for querying the flash name and id
- mtd parser reorganization
SPI NOR core changes:
- always use bounce buffer for register read/writes
- move m25p80 code in spi-nor.c
- rework hwcaps selection for the spi-mem case
- rework the core in order to move the manufacturer specific code out
of it:
- regroup flash parameters in 'struct spi_nor_flash_parameter'
- add default_init() and post_sfdp() hooks to tweak the flash
parameters
- introduce the ->set_4byte(), ->convert_addr() and ->setup()
methods, to deal with manufacturer specific code
- rework the SPI NOR lock/unlock logic
- fix an error code in spi_nor_read_raw()
- fix a memory leak bug
- enable the debugfs for the partname and partid
- add support for few flashes
SPI NOR controller drivers changes:
- intel-spi:
- Whitelist 4B read commands
- Add support for Intel Tiger Lake SPI serial flash
- aspeed-smc: Add of_node_put()
- hisi-sfc: add of_node_put()
- cadence-quadspi: Fix QSPI RCU Schedule Stall
NAND core:
- Fixing typos
- Adding missing of_node_put() in various drivers
Raw NAND controller drivers:
- Macronix: new controller driver
- Omap2: fix the number of bitflips returned
- Brcmnand: fix a pointer not iterating over all the page chunks
- W90x900: driver removed
- Onenand: fix a memory leak
- Sharpsl: missing include guard
- STM32: avoid warnings when building with W=1
- Ingenic: fix a coccinelle warning
- r852: call a helper to simplify the code
CFI core:
- Kill useless initializer in mtd_do_chip_probe()
- Fix a rare write failure seen on some cfi_cmdset_0002 compliant
Parallel NORs
- Bunch of cleanups for cfi_cmdset_0002 driver's write functions by
Tokunori Ikegami"
* tag 'mtd/for-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (77 commits)
mtd: pmc551: Remove set but not used variable 'soff_lo'
mtd: cfi_cmdset_0002: Fix do_erase_chip() to get chip as erasing mode
mtd: sm_ftl: Fix memory leak in sm_init_zone() error path
mtd: parsers: Move CMDLINE parser
mtd: parsers: Move OF parser
mtd: parsers: Move BCM63xx parser
mtd: parsers: Move BCM47xx parser
mtd: parsers: Move TI AR7 parser
mtd: pismo: Simplify getting the adapter of a client
mtd: phram: Module parameters add writable permissions
mtd: pxa2xx: Use ioremap_cache insted of ioremap_cached
mtd: spi-nor: Rename "n25q512a" to "mt25qu512a (n25q512a)"
mtd: spi-nor: Add support for mt35xu02g
mtd: rawnand: omap2: Fix number of bitflips reporting with ELM
mtd: rawnand: brcmnand: Fix ecc chunk calculation for erased page bitfips
mtd: spi-nor: remove superfluous pass of nor->info->sector_size
mtd: spi-nor: enable the debugfs for the partname and partid
mtd: mtdcore: add debugfs nodes for querying the flash name and id
mtd: spi-nor: hisi-sfc: Add of_node_put() before break
mtd: spi-nor: aspeed-smc: Add of_node_put()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm updates from Dan Williams:
"Some reworks to better support nvdimms on powerpc and an nvdimm
security interface update:
- Rework the nvdimm core to accommodate architectures with different
page sizes and ones that can change supported huge page sizes at
boot time rather than a compile time constant.
- Introduce a distinct 'frozen' attribute for the nvdimm security
state since it is independent of the locked state.
- Miscellaneous fixups"
* tag 'libnvdimm-for-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
libnvdimm: Use PAGE_SIZE instead of SZ_4K for align check
libnvdimm/label: Remove the dpa align check
libnvdimm/pfn_dev: Add page size and struct page size to pfn superblock
libnvdimm/pfn_dev: Add a build check to make sure we notice when struct page size change
libnvdimm/pmem: Advance namespace seed for specific probe errors
libnvdimm/region: Rewrite _probe_success() to _advance_seeds()
libnvdimm/security: Consolidate 'security' operations
libnvdimm/security: Tighten scope of nvdimm->busy vs security operations
libnvdimm/security: Introduce a 'frozen' attribute
libnvdimm, region: Use struct_size() in kzalloc()
tools/testing/nvdimm: Fix fallthrough warning
libnvdimm/of_pmem: Provide a unique name for bus provider
|
|
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: qla2xxx, ufs, smartpqi,
lpfc, hisi_sas, qedf, mpt3sas; plus a whole load of minor updates. The
only core change this time around is the addition of request batching
for virtio. Since batching requires an additional flag to use, it
should be invisible to the rest of the drivers"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (264 commits)
scsi: hisi_sas: Fix the conflict between device gone and host reset
scsi: hisi_sas: Add BIST support for phy loopback
scsi: hisi_sas: Add hisi_sas_debugfs_alloc() to centralise allocation
scsi: hisi_sas: Remove some unused function arguments
scsi: hisi_sas: Remove redundant work declaration
scsi: hisi_sas: Remove hisi_sas_hw.slot_complete
scsi: hisi_sas: Assign NCQ tag for all NCQ commands
scsi: hisi_sas: Update all the registers after suspend and resume
scsi: hisi_sas: Retry 3 times TMF IO for SAS disks when init device
scsi: hisi_sas: Remove sleep after issue phy reset if sas_smp_phy_control() fails
scsi: hisi_sas: Directly return when running I_T_nexus reset if phy disabled
scsi: hisi_sas: Use true/false as input parameter of sas_phy_reset()
scsi: hisi_sas: add debugfs auto-trigger for internal abort time out
scsi: virtio_scsi: unplug LUNs when events missed
scsi: scsi_dh_rdac: zero cdb in send_mode_select()
scsi: fcoe: fix null-ptr-deref Read in fc_release_transport
scsi: ufs-hisi: use devm_platform_ioremap_resource() to simplify code
scsi: ufshcd: use devm_platform_ioremap_resource() to simplify code
scsi: hisi_sas: use devm_platform_ioremap_resource() to simplify code
scsi: ufs: Use kmemdup in ufshcd_read_string_desc()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper updates from Mike Snitzer:
- crypto and DM crypt advances that allow the crypto API to reclaim
implementation details that do not belong in DM crypt. The wrapper
template for ESSIV generation that was factored out will also be used
by fscrypt in the future.
- Add root hash pkcs#7 signature verification to the DM verity target.
- Add a new "clone" DM target that allows for efficient remote
replication of a device.
- Enhance DM bufio's cache to be tailored to each client based on use.
Clients that make heavy use of the cache get more of it, and those
that use less have reduced cache usage.
- Add a new DM_GET_TARGET_VERSION ioctl to allow userspace to query the
version number of a DM target (even if the associated module isn't
yet loaded).
- Fix invalid memory access in DM zoned target.
- Fix the max_discard_sectors limit advertised by the DM raid target;
it was mistakenly storing the limit in bytes rather than sectors.
- Small optimizations and cleanups in DM writecache target.
- Various fixes and cleanups in DM core, DM raid1 and space map portion
of DM persistent data library.
* tag 'for-5.4/dm-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm: (22 commits)
dm: introduce DM_GET_TARGET_VERSION
dm bufio: introduce a global cache replacement
dm bufio: remove old-style buffer cleanup
dm bufio: introduce a global queue
dm bufio: refactor adjust_total_allocated
dm bufio: call adjust_total_allocated from __link_buffer and __unlink_buffer
dm: add clone target
dm raid: fix updating of max_discard_sectors limit
dm writecache: skip writecache_wait for pmem mode
dm stats: use struct_size() helper
dm crypt: omit parsing of the encapsulated cipher
dm crypt: switch to ESSIV crypto API template
crypto: essiv - create wrapper template for ESSIV generation
dm space map common: remove check for impossible sm_find_free() return value
dm raid1: use struct_size() with kzalloc()
dm writecache: optimize performance by sorting the blocks for writeback_all
dm writecache: add unlikely for getting two block with same LBA
dm writecache: remove unused member pointer in writeback_struct
dm zoned: fix invalid memory access
dm verity: add root hash pkcs#7 signature verification
...
|
|
Pull RDMA subsystem updates from Jason Gunthorpe:
"This cycle mainly saw lots of bug fixes and clean up code across the
core code and several drivers, few new functional changes were made.
- Many cleanup and bug fixes for hns
- Various small bug fixes and cleanups in hfi1, mlx5, usnic, qed,
bnxt_re, efa
- Share the query_port code between all the iWarp drivers
- General rework and cleanup of the ODP MR umem code to fit better
with the mmu notifier get/put scheme
- Support rdma netlink in non init_net name spaces
- mlx5 support for XRC devx and DC ODP"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (99 commits)
RDMA: Fix double-free in srq creation error flow
RDMA/efa: Fix incorrect error print
IB/mlx5: Free mpi in mp_slave mode
IB/mlx5: Use the original address for the page during free_pages
RDMA/bnxt_re: Fix spelling mistake "missin_resp" -> "missing_resp"
RDMA/hns: Package operations of rq inline buffer into separate functions
RDMA/hns: Optimize cmd init and mode selection for hip08
IB/hfi1: Define variables as unsigned long to fix KASAN warning
IB/{rdmavt, hfi1, qib}: Add a counter for credit waits
IB/hfi1: Add traces for TID RDMA READ
RDMA/siw: Relax from kmap_atomic() use in TX path
IB/iser: Support up to 16MB data transfer in a single command
RDMA/siw: Fix page address mapping in TX path
RDMA: Fix goto target to release the allocated memory
RDMA/usnic: Avoid overly large buffers on stack
RDMA/odp: Add missing cast for 32 bit
RDMA/hns: Use devm_platform_ioremap_resource() to simplify code
Documentation/infiniband: update name of some functions
RDMA/cma: Fix false error message
RDMA/hns: Fix wrong assignment of qp_access_flags
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull hmm updates from Jason Gunthorpe:
"This is more cleanup and consolidation of the hmm APIs and the very
strongly related mmu_notifier interfaces. Many places across the tree
using these interfaces are touched in the process. Beyond that a
cleanup to the page walker API and a few memremap related changes
round out the series:
- General improvement of hmm_range_fault() and related APIs, more
documentation, bug fixes from testing, API simplification &
consolidation, and unused API removal
- Simplify the hmm related kconfigs to HMM_MIRROR and DEVICE_PRIVATE,
and make them internal kconfig selects
- Hoist a lot of code related to mmu notifier attachment out of
drivers by using a refcount get/put attachment idiom and remove the
convoluted mmu_notifier_unregister_no_release() and related APIs.
- General API improvement for the migrate_vma API and revision of its
only user in nouveau
- Annotate mmu_notifiers with lockdep and sleeping region debugging
Two series unrelated to HMM or mmu_notifiers came along due to
dependencies:
- Allow pagemap's memremap_pages family of APIs to work without
providing a struct device
- Make walk_page_range() and related use a constant structure for
function pointers"
* tag 'for-linus-hmm' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (75 commits)
libnvdimm: Enable unit test infrastructure compile checks
mm, notifier: Catch sleeping/blocking for !blockable
kernel.h: Add non_block_start/end()
drm/radeon: guard against calling an unpaired radeon_mn_unregister()
csky: add missing brackets in a macro for tlb.h
pagewalk: use lockdep_assert_held for locking validation
pagewalk: separate function pointers from iterator data
mm: split out a new pagewalk.h header from mm.h
mm/mmu_notifiers: annotate with might_sleep()
mm/mmu_notifiers: prime lockdep
mm/mmu_notifiers: add a lockdep map for invalidate_range_start/end
mm/mmu_notifiers: remove the __mmu_notifier_invalidate_range_start/end exports
mm/hmm: hmm_range_fault() infinite loop
mm/hmm: hmm_range_fault() NULL pointer bug
mm/hmm: fix hmm_range_fault()'s handling of swapped out pages
mm/mmu_notifiers: remove unregister_no_release
RDMA/odp: remove ib_ucontext from ib_umem
RDMA/odp: use mmu_notifier_get/put for 'struct ib_ucontext_per_mm'
RDMA/mlx5: Use odp instead of mr->umem in pagefault_mr
RDMA/mlx5: Use ib_umem_start instead of umem.address
...
|
|
On 32-bit:
drivers/net/wireless/zydas/zd1211rw/zd_usb.c: In function ‘check_read_regs’:
drivers/net/wireless/zydas/zd1211rw/zd_def.h:18:25: warning: format ‘%ld’ expects argument of type ‘long int’, but argument 6 has type ‘size_t’ {aka ‘unsigned int’} [-Wformat=]
dev_printk(level, dev, "%s() " fmt, __func__, ##args)
^~~~~~~
drivers/net/wireless/zydas/zd1211rw/zd_def.h:22:4: note: in expansion of macro ‘dev_printk_f’
dev_printk_f(KERN_DEBUG, dev, fmt, ## args)
^~~~~~~~~~~~
drivers/net/wireless/zydas/zd1211rw/zd_usb.c:1635:3: note: in expansion of macro ‘dev_dbg_f’
dev_dbg_f(zd_usb_dev(usb),
^~~~~~~~~
drivers/net/wireless/zydas/zd1211rw/zd_usb.c:1636:51: note: format string is defined here
"error: actual length %d less than expected %ld\n",
~~^
%d
Fixes: 84b0b66352470e64 ("zd1211rw: zd_usb: Use struct_size() helper")
Signed-off-by: Geert Uytterhoeven <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
|
|
Interrupt is disabled to stop PCI, which means the skbs
queued for each TX ring will not be released via DMA
interrupt. To avoid those skbs remained being left in
the skb queue until PCI has been removed, driver needs
to release skbs by itself.
Signed-off-by: Yan-Hsuan Chuang <[email protected]>
Reviewed-by: Brian Norris <[email protected]>
Tested-by: Brian Norris <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
|
|
These skbs free routines could be used when driver wants
to stop PCI bus, because some of the skbs remained in the
queue may not have been returned via DMA interrupt.
Signed-off-by: Yan-Hsuan Chuang <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
|
|
This patch drop the check for of_device_get_match_data. Due to the only
way call driver probe is compatible match. The data pointer which points
to the SoC specify data is directly set by driver, and it should not be
NULL in our case. We can safety remove the check for the result of
of_device_get_match_data().
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Sam Shih <[email protected]>
Acked-by: Uwe Kleine-König <[email protected]>
Signed-off-by: Thierry Reding <[email protected]>
|
|
This helps readability by separating the driver-specific bits from the
PWM framework bits.
Signed-off-by: Thierry Reding <[email protected]>
|
|
Since the driver is now exclusively DT, it only binds if it finds a
match in the of_device_id table. But in that case the associated data
can never be NULL, so drop the unnecessary check.
While at it, drop the extra local variable and store the pointer to
this per-SoC data in the driver data directly.
Signed-off-by: Thierry Reding <[email protected]>
|
|
Since commit 26202873bb51 ("avr32: remove support for AVR32
architecture") there is no more user of platform_device_id and we
should only use dt bindings
Signed-off-by: Kamel Bouhara <[email protected]>
Acked-by: Alexandre Belloni <[email protected]>
Acked-by: Claudiu Beznea <[email protected]>
Acked-by: Uwe Kleine-König <[email protected]>
Signed-off-by: Thierry Reding <[email protected]>
|
|
LPTimer can use a 32KHz clock for counting. It depends on clock tree
configuration. In such a case, PWM output frequency range is limited.
Although unlikely, nothing prevents user from requesting a PWM frequency
above counting clock (32KHz for instance):
- This causes (prd - 1) = 0xffff to be written in ARR register later in
the apply() routine.
This results in badly configured PWM period (and also duty_cycle).
Add a check to report an error is such a case.
Signed-off-by: Fabrice Gasnier <[email protected]>
Reviewed-by: Uwe Kleine-König <[email protected]>
Signed-off-by: Thierry Reding <[email protected]>
|
|
It is surprising for a PWM consumer when the variable holding the
requested state is modified by pwm_apply_state(). Consider for example a
driver doing:
#define PERIOD 5000000
#define DUTY_LITTLE 10
...
struct pwm_state state = {
.period = PERIOD,
.duty_cycle = DUTY_LITTLE,
.polarity = PWM_POLARITY_NORMAL,
.enabled = true,
};
pwm_apply_state(mypwm, &state);
...
state.duty_cycle = PERIOD / 2;
pwm_apply_state(mypwm, &state);
For sure the second call to pwm_apply_state() should still have
state.period = PERIOD and not something the hardware driver chose for a
reason that doesn't necessarily apply to the second call.
So declare the state argument as a pointer to a const type and adapt all
drivers' .apply callbacks.
Signed-off-by: Uwe Kleine-König <[email protected]>
Signed-off-by: Thierry Reding <[email protected]>
|
|
Julian noted that rt_uses_gateway has a more subtle use than 'is gateway
set':
https://lore.kernel.org/netdev/[email protected]/
Revert that part of the commit referenced in the Fixes tag.
Currently, there are no u8 holes in 'struct rtable'. There is a 4-byte hole
in the second cacheline which contains the gateway declaration. So move
rt_gw_family down to the gateway declarations since they are always used
together, and then re-use that u8 for rt_uses_gateway. End result is that
rtable size is unchanged.
Fixes: 1550c171935d ("ipv4: Prepare rtable for IPv6 gateway")
Reported-by: Julian Anastasov <[email protected]>
Signed-off-by: David Ahern <[email protected]>
Reviewed-by: Julian Anastasov <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
The pwm-fsl-ftm driver is one of only three PWM drivers which updates
the state for the caller of pwm_apply_state(). This might have
surprising results if the caller reuses the values expecting them to
still represent the same state.
Signed-off-by: Uwe Kleine-König <[email protected]>
Signed-off-by: Thierry Reding <[email protected]>
|
|
The pwm-sun4i driver is one of only three PWM drivers which updates the
state for the caller of pwm_apply_state(). This might have surprising
results if the caller reuses the values expecting them to still
represent the same state.
Signed-off-by: Uwe Kleine-König <[email protected]>
Signed-off-by: Thierry Reding <[email protected]>
|
|
The pwm-rockchip driver is one of only three PWM drivers which updates
the state for the caller of pwm_apply_state(). This might have
surprising results if the caller reuses the values expecting them to
still represent the same state.
Signed-off-by: Uwe Kleine-König <[email protected]>
Signed-off-by: Thierry Reding <[email protected]>
|
|
When pwm_apply_state() is called the lowlevel driver usually has to
apply some rounding because the hardware doesn't support nanosecond
resolution. So let pwm_get_state() return the actually implemented state
instead of the last applied one if possible.
Signed-off-by: Uwe Kleine-König <[email protected]>
Signed-off-by: Thierry Reding <[email protected]>
|
|
pwm->chip is dereferenced several times in the pwm_apply_state()
function. Introducing a local variable for it helps keeping some lines a
bit shorter.
Signed-off-by: Uwe Kleine-König <[email protected]>
Signed-off-by: Thierry Reding <[email protected]>
|
|
Don't rely on *state being zero initialized and PWM_POLARITY_NORMAL
being zero. So always assign .polarity.
Signed-off-by: Uwe Kleine-König <[email protected]>
Signed-off-by: Thierry Reding <[email protected]>
|
|
This suppresses error messages in case the PWM clock isn't ready yet.
Signed-off-by: Stefan Wahren <[email protected]>
Reviewed-by: Uwe Kleine-König <[email protected]>
Signed-off-by: Thierry Reding <[email protected]>
|
|
The range check for period_ns was written under assumption of a fixed
PWM clock. With clk-bcm2835 driver the PWM clock is a dynamic one.
So fix this by doing the range check on the period register value.
Signed-off-by: Stefan Wahren <[email protected]>
Acked-by: Uwe Kleine-König <[email protected]>
Signed-off-by: Thierry Reding <[email protected]>
|
|
The PWM config can be triggered via sysfs, so we better suppress the
error message in case of an invalid period to avoid kernel log spamming.
Signed-off-by: Stefan Wahren <[email protected]>
Acked-by: Uwe Kleine-König <[email protected]>
Signed-off-by: Thierry Reding <[email protected]>
|
|
Since the rcar_pwm_apply() has already checked whether state->enabled
is set or not, this patch removes a redundant condition.
Signed-off-by: Yoshihiro Shimoda <[email protected]>
Reviewed-by: Geert Uytterhoeven <[email protected]>
Reviewed-by: Uwe Kleine-König <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Signed-off-by: Thierry Reding <[email protected]>
|
|
This patch adds the Spreadtrum PWM support, which provides maximum 4
channels.
Signed-off-by: Neo Hou <[email protected]>
Signed-off-by: Baolin Wang <[email protected]>
Signed-off-by: Thierry Reding <[email protected]>
|
|
Add the compatible and the platform data to support PWM on the MT8516
SoC.
Signed-off-by: Fabien Parent <[email protected]>
Reviewed-by: Matthias Brugger <[email protected]>
Acked-by: Uwe Kleine-König <[email protected]>
Signed-off-by: Thierry Reding <[email protected]>
|
|
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Thierry Reding <[email protected]>
Cc: [email protected]
Cc: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Stephen Boyd <[email protected]>
Signed-off-by: Thierry Reding <[email protected]>
|
|
Signed-off-by: Uwe Kleine-König <[email protected]>
Signed-off-by: Thierry Reding <[email protected]>
|
|
The JZ4740 PWM implementation doesn't fulfill the (up to now
insufficiently documented) requirements of the PWM API. At least
document them in the driver.
Signed-off-by: Uwe Kleine-König <[email protected]>
Reviewed-by: Paul Cercueil <[email protected]>
Signed-off-by: Thierry Reding <[email protected]>
|
|
Pull ARM SoC late updates from Arnd Bergmann:
"This is some material that we picked up into our tree late or that had
complex inter-depondencies. The fact that there are these
interdependencies tends to meant that these are often actually the
most interesting new additions:
- The new Aspeed AST2600 baseboard management controller is added,
this is a Cortex-A7 based follow-up to the ARM11 based AST2500 and
had some dependencies on other device drivers.
- After many years, support for the MMP2 based OLPC XO-1.75 finally
makes it into the kernel.
- The Armada 3720 based Turris Mox open source router platform is a
late addition and it follows some preparatory work across multiple
branches.
- The OMAP2+ platform had some large-scale cleanup involving driver
changes and DT changes, here we finish it off, dropping a lot of
the now-unused platform data.
- The TI K3 platform that got added for 5.3 gains a lot more support
for individual bits on the SoC, this part just came late for the
merge window"
[ This pull request itself wasn't actually sent late at all by Arnd, but
I waited on the branches that it used to be pulled first, so it ends
up being merged much later than the other ARM SoC pull requests this
merge window - Linus ]
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (57 commits)
ARM: dts: dir685: Drop spi-cpol from the display
ARM: dts: aspeed: Add AST2600 pinmux nodes
ARM: dts: aspeed: Add AST2600 and EVB
ARM: exynos: Enable support for ARM architected timers
ARM: samsung: Fix system restart on S3C6410
ARM: dts: mmp2: add OLPC XO 1.75 machine
ARM: dts: mmp2: rename the USB PHY node
ARM: dts: mmp2: specify reg-shift for the UARTs
ARM: dts: mmp2: add camera interfaces
ARM: dts: mmp2: fix the SPI nodes
ARM: dts: mmp2: trivial whitespace fix
arm64: dts: marvell: add DTS for Turris Mox
dt-bindings: marvell: document Turris Mox compatible
arm64: dts: marvell: armada-37xx: add SPI CS1 pinctrl
arm64: dts: ti: k3-j721e-main: Fix gic-its node unit-address
arm64: dts: ti: k3-am65-main: Fix gic-its node unit-address
arm64: dts: ti: k3-j721e-main: Add hwspinlock node
arm64: dts: ti: k3-am65-main: Add hwspinlock node
arm64: dts: k3-j721e: Add gpio-keys on common processor board
dt-bindings: pinctrl: k3: Introduce pinmux definitions for J721E
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"We have a small collection of core framework updates this time, mostly
around clk registration by clk providers and debugfs "nice to haves"
for rate constraints. I'll highlight that we're now setting the
clk_init_data pointer inside struct clk_hw to NULL during
clk_register(), which may break some drivers that thought they could
use that pointer during normal operations. That change has been
sitting in next for a while now but maybe something is still broken.
We'l see. Other than that the core framework changes aren't invasive
and they're fixing bugs, simplifying, and making things better.
On the clk driver side we got the usual addition of new SoC support,
new features for existing drivers, and bug fixes scattered throughout.
The biggest diffstat is the Amlogic driver that gained CPU clk support
in addition to migrating to the new way of specifying clk parents.
After that the Qualcomm, i.MX, Mediatek, and Rockchip clk drivers got
support for various new SoCs and clock controllers from those vendors.
Core:
- Drop NULL checks in clk debugfs
- Add min/max rates to clk debugfs
- Set clk_init_data pointer inside clk_hw to NULL after registration
- Make clk_bulk_get_all() return an 'id' corresponding to clock-names
- Evict parents from parent cache when they're unregistered
New Drivers:
- Add clock driver for i.MX8MN SoCs
- Support aspeed AST2600 SoCs
- Support for Mediatek MT6779 SoCs
- Support qcom SM8150 GCC and RPMh clks
- Support qcom QCS404 WCSS clks
- Add CPU clock support for Armada 7K/8K (specifically AP806 and AP807)
- Addition of clock driver for Rockchip rk3308 SoCs
Updates:
- Add regulator support to the cdce925 clk driver
- Add support for Raspberry Pi 4 bcm2711 SoCs
- Add SDIO gate support to aspeed driver
- Add missing of_node_put() calls in various clk drivers
- Migrate Amlogic driver to new clock parent description method
- Add DVFS support to Amlogic Meson g12
- Add Amlogic Meson g12a reset support to the axg audio clock controller
- Add sm1 support to the Amlogic Meson g12a clock controller
- Switch i.MX8MM clock driver to platform driver
- Add Hifi4 DSP related clocks for i.MX8QXP SoC
- Fix Audio PLL setting and parent clock for USB
- Misc i.MX8 clock driver improvements and corrections
- Set floor ops for Qualcomm SD clks so that rounding works
- Fix "always-on" Clock Domains on Renesas R-Car M1A, RZ/A1, RZ/A2, and RZ/N1
- Enable the Allwinner V3 SoC and fix the i2s clock for H6"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (137 commits)
clk: Drop !clk checks in debugfs dumping
clk: imx: imx8mn: fix pll mux bit
clk: imx: imx8mm: fix pll mux bit
clk: imx: clk-pll14xx: unbypass PLL by default
clk: imx: pll14xx: avoid glitch when set rate
clk: mvebu: ap80x: add AP807 clock support
clk: mvebu: ap806: Prepare the introduction of AP807 clock support
clk: mvebu: ap806: add AP-DCLK (hclk) to system controller driver
clk: mvebu: ap806: be more explicit on what SaR is
clk: mvebu: ap80x-cpu: add AP807 CPU clock support
clk: mvebu: ap806-cpu: prepare mapping of AP807 CPU clock
dt-bindings: ap806: Document AP807 clock compatible
dt-bindings: ap80x: Document AP807 CPU clock compatible
clk: sprd: add missing kfree
clk: at91: allow 24 Mhz clock as input for PLL
clk: Make clk_bulk_get_all() return a valid "id"
clk: actions: Fix factor clk struct member access
clk: qcom: rcg: Return failure for RCG update
clk: remove extra ---help--- tags in Kconfig
clk: add include guard to clk-conf.h
...
|
|
devm_ioremap_resource() already outputs an error message, so remove the
extra error message on failure.
Signed-off-by: Ding Xiang <[email protected]>
Acked-by: Uwe Kleine-König <[email protected]>
Signed-off-by: Thierry Reding <[email protected]>
|
|
Use the new helper devm_platform_ioremap_resource() which wraps the
platform_get_resource() and devm_ioremap_resource() together, to
simplify the code.
Signed-off-by: Anson Huang <[email protected]>
Reviewed-by: Dong Aisheng <[email protected]>
Acked-by: Uwe Kleine-König <[email protected]>
Signed-off-by: Thierry Reding <[email protected]>
|
|
Pull VFIO updates from Alex Williamson:
- Fix spapr iommu error case case (Alexey Kardashevskiy)
- Consolidate region type definitions (Cornelia Huck)
- Restore saved original PCI state on release (hexin)
- Simplify mtty sample driver interrupt path (Parav Pandit)
- Support for reporting valid IOVA regions to user (Shameer Kolothum)
* tag 'vfio-v5.4-rc1' of git://github.com/awilliam/linux-vfio:
vfio_pci: Restore original state on release
vfio/type1: remove duplicate retrieval of reserved regions
vfio/type1: Add IOVA range capability support
vfio/type1: check dma map request is within a valid iova range
vfio/spapr_tce: Fix incorrect tce_iommu_group memory free
vfio-mdev/mtty: Simplify interrupt generation
vfio: re-arrange vfio region definitions
vfio/type1: Update iova list on detach
vfio/type1: Check reserved region conflict and update iova list
vfio/type1: Introduce iova list and add iommu aperture validity check
|
|
Add support to get regulator information of 3.3V and 12V supplies of a PCIe
slot from the respective controller's device-tree node and enable those
supplies. This is required in platforms like p2972-0000 where the supplies
to x16 slot owned by C5 controller need to be enabled before attempting to
enumerate the devices.
Signed-off-by: Vidya Sagar <[email protected]>
Signed-off-by: Lorenzo Pieralisi <[email protected]>
Reviewed-by: Andrew Murray <[email protected]>
Acked-by: Thierry Reding <[email protected]>
|
|
Add support to configure sideband signal pins when the information is
present in the respective controller device-tree node.
Signed-off-by: Vidya Sagar <[email protected]>
Signed-off-by: Lorenzo Pieralisi <[email protected]>
[bhelgaas: fold in YueHaibing's fix for build error without CONFIG_PINCTRL;
https://lore.kernel.org/r/[email protected]]
Signed-off-by: Bjorn Helgaas <[email protected]>
Reviewed-by: Andrew Murray <[email protected]>
Acked-by: Thierry Reding <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"This is a bit late, partly due to me travelling, and partly due to a
power outage knocking out some of my test systems *while* I was
travelling.
- Initial support for running on a system with an Ultravisor, which
is software that runs below the hypervisor and protects guests
against some attacks by the hypervisor.
- Support for building the kernel to run as a "Secure Virtual
Machine", ie. as a guest capable of running on a system with an
Ultravisor.
- Some changes to our DMA code on bare metal, to allow devices with
medium sized DMA masks (> 32 && < 59 bits) to use more than 2GB of
DMA space.
- Support for firmware assisted crash dumps on bare metal (powernv).
- Two series fixing bugs in and refactoring our PCI EEH code.
- A large series refactoring our exception entry code to use gas
macros, both to make it more readable and also enable some future
optimisations.
As well as many cleanups and other minor features & fixups.
Thanks to: Adam Zerella, Alexey Kardashevskiy, Alistair Popple, Andrew
Donnellan, Aneesh Kumar K.V, Anju T Sudhakar, Anshuman Khandual,
Balbir Singh, Benjamin Herrenschmidt, Cédric Le Goater, Christophe
JAILLET, Christophe Leroy, Christopher M. Riedl, Christoph Hellwig,
Claudio Carvalho, Daniel Axtens, David Gibson, David Hildenbrand,
Desnes A. Nunes do Rosario, Ganesh Goudar, Gautham R. Shenoy, Greg
Kurz, Guerney Hunt, Gustavo Romero, Halil Pasic, Hari Bathini, Joakim
Tjernlund, Jonathan Neuschafer, Jordan Niethe, Leonardo Bras, Lianbo
Jiang, Madhavan Srinivasan, Mahesh Salgaonkar, Mahesh Salgaonkar,
Masahiro Yamada, Maxiwell S. Garcia, Michael Anderson, Nathan
Chancellor, Nathan Lynch, Naveen N. Rao, Nicholas Piggin, Oliver
O'Halloran, Qian Cai, Ram Pai, Ravi Bangoria, Reza Arbab, Ryan Grimm,
Sam Bobroff, Santosh Sivaraj, Segher Boessenkool, Sukadev Bhattiprolu,
Thiago Bauermann, Thiago Jung Bauermann, Thomas Gleixner, Tom
Lendacky, Vasant Hegde"
* tag 'powerpc-5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (264 commits)
powerpc/mm/mce: Keep irqs disabled during lockless page table walk
powerpc: Use ftrace_graph_ret_addr() when unwinding
powerpc/ftrace: Enable HAVE_FUNCTION_GRAPH_RET_ADDR_PTR
ftrace: Look up the address of return_to_handler() using helpers
powerpc: dump kernel log before carrying out fadump or kdump
docs: powerpc: Add missing documentation reference
powerpc/xmon: Fix output of XIVE IPI
powerpc/xmon: Improve output of XIVE interrupts
powerpc/mm/radix: remove useless kernel messages
powerpc/fadump: support holes in kernel boot memory area
powerpc/fadump: remove RMA_START and RMA_END macros
powerpc/fadump: update documentation about option to release opalcore
powerpc/fadump: consider f/w load area
powerpc/opalcore: provide an option to invalidate /sys/firmware/opal/core file
powerpc/opalcore: export /sys/firmware/opal/core for analysing opal crashes
powerpc/fadump: update documentation about CONFIG_PRESERVE_FA_DUMP
powerpc/fadump: add support to preserve crash data on FADUMP disabled kernel
powerpc/fadump: improve how crashed kernel's memory is reserved
powerpc/fadump: consider reserved ranges while releasing memory
powerpc/fadump: make crash memory ranges array allocation generic
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild updates from Masahiro Yamada:
- add modpost warn exported symbols marked as 'static' because 'static'
and EXPORT_SYMBOL is an odd combination
- break the build early if gold linker is used
- optimize the Bison rule to produce .c and .h files by a single
pattern rule
- handle PREEMPT_RT in the module vermagic and UTS_VERSION
- warn CONFIG options leaked to the user-space except existing ones
- make single targets work properly
- rebuild modules when module linker scripts are updated
- split the module final link stage into scripts/Makefile.modfinal
- fix the missed error code in merge_config.sh
- improve the error message displayed on the attempt of the O= build in
unclean source tree
- remove 'clean-dirs' syntax
- disable -Wimplicit-fallthrough warning for Clang
- add CONFIG_CC_OPTIMIZE_FOR_SIZE_O3 for ARC
- remove ARCH_{CPP,A,C}FLAGS variables
- add $(BASH) to run bash scripts
- change *CFLAGS_<basetarget>.o to take the relative path to $(obj)
instead of the basename
- stop suppressing Clang's -Wunused-function warnings when W=1
- fix linux/export.h to avoid genksyms calculating CRC of trimmed
exported symbols
- misc cleanups
* tag 'kbuild-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (63 commits)
genksyms: convert to SPDX License Identifier for lex.l and parse.y
modpost: use __section in the output to *.mod.c
modpost: use MODULE_INFO() for __module_depends
export.h, genksyms: do not make genksyms calculate CRC of trimmed symbols
export.h: remove defined(__KERNEL__), which is no longer needed
kbuild: allow Clang to find unused static inline functions for W=1 build
kbuild: rename KBUILD_ENABLE_EXTRA_GCC_CHECKS to KBUILD_EXTRA_WARN
kbuild: refactor scripts/Makefile.extrawarn
merge_config.sh: ignore unwanted grep errors
kbuild: change *FLAGS_<basetarget>.o to take the path relative to $(obj)
modpost: add NOFAIL to strndup
modpost: add guid_t type definition
kbuild: add $(BASH) to run scripts with bash-extension
kbuild: remove ARCH_{CPP,A,C}FLAGS
kbuild,arc: add CONFIG_CC_OPTIMIZE_FOR_PERFORMANCE_O3 for ARC
kbuild: Do not enable -Wimplicit-fallthrough for clang for now
kbuild: clean up subdir-ymn calculation in Makefile.clean
kbuild: remove unneeded '+' marker from cmd_clean
kbuild: remove clean-dirs syntax
kbuild: check clean srctree even earlier
...
|
|
When naming the new devices, instead of using the ACPI ID in
the name as base, using the parent device's name. That makes
it possible to support multiple multi-instance i2c devices
of the same type in the same system.
This fixes an issue seen on some Intel Kaby Lake based
boards:
sysfs: cannot create duplicate filename '/devices/pci0000:00/0000:00:15.0/i2c_designware.0/i2c-0/i2c-INT3515-tps6598x.0'
Fixes: 2336dfadfb1e ("platform/x86: i2c-multi-instantiate: Allow to have same slaves")
Cc: [email protected]
Signed-off-by: Heikki Krogerus <[email protected]>
Reviewed-by: Hans de Goede <[email protected]>
Signed-off-by: Andy Shevchenko <[email protected]>
|