aboutsummaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)AuthorFilesLines
2022-08-30drm/amd/display: Fix DCN32 DPSTREAMCLK_CNTL programmingGeorge Shen2-6/+6
[Why] Each index in the DPSTREAMCLK_CNTL register phyiscally maps 1-to-1 with HPO stream encoder instance. On the other hand, each index in DTBCLK_P_CNTL physically maps 1-to-1 with OTG instance. Current DCN32 DPSTREAMCLK_CLK programing assumes that OTG instance always maps 1-to-1 with HPO stream encoder instance. This is not always guaranteed and can result in blackscreen. [How] Program the correct dpstreamclk instance with the correct dtbclk_p source. Reviewed-by: Ariel Bernstein <[email protected]> Acked-by: Brian Chang <[email protected]> Signed-off-by: George Shen <[email protected]> Tested-by: Daniel Wheeler <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2022-08-30drm/amdgpu: Update mes_v11_api_def.hGraham Sider2-1/+3
New GFX11 MES FW adds the trap_en bit. For now hardcode to 1 (traps enabled). Signed-off-by: Graham Sider <[email protected]> Acked-by: Felix Kuehling <[email protected]> Reviewed-by: Harish Kasiviswanathan <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2022-08-30drm/amdgpu: disable FRU access on special SIENNA CICHLID cardGuchun Chen1-2/+7
Below driver load error will be printed, not friendly to end user. amdgpu: ATOM BIOS: 113-D603GLXE-077 [drm] FRU: Failed to get size field [drm:amdgpu_fru_get_product_info [amdgpu]] *ERROR* Failed to read FRU Manufacturer, ret:-5 Signed-off-by: Guchun Chen <[email protected]> Reviewed-by: Kent Russell <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2022-08-30wifi: iwlegacy: 4965: corrected fix for potential off-by-one overflow in ↵Stanislaw Gruszka1-4/+1
il4965_rs_fill_link_cmd() This reverts commit a8eb8e6f7159c7c20c0ddac428bde3d110890aa7 as it can cause invalid link quality command sent to the firmware and address the off-by-one issue by fixing condition of while loop. Cc: [email protected] Fixes: a8eb8e6f7159 ("wifi: iwlegacy: 4965: fix potential off-by-one overflow in il4965_rs_fill_link_cmd()") Signed-off-by: Stanislaw Gruszka <[email protected]> Signed-off-by: Kalle Valo <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2022-08-30wifi: wilc1000: fix DMA on stack objects[email protected]3-8/+47
Sometimes 'wilc_sdio_cmd53' is called with addresses pointing to an object on the stack. Use dynamically allocated memory for cmd53 instead of stack address which is not DMA'able. Fixes: 5625f965d764 ("wilc1000: move wilc driver out of staging") Reported-by: Michael Walle <[email protected]> Suggested-by: Michael Walle <[email protected]> Signed-off-by: Ajay Singh <[email protected]> Reviewed-by: Michael Walle <[email protected]> Tested-by: Michael Walle <[email protected]> Signed-off-by: Kalle Valo <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2022-08-30staging: rtl8712: fix use after free bugsDan Carpenter1-36/+0
_Read/Write_MACREG callbacks are NULL so the read/write_macreg_hdl() functions don't do anything except free the "pcmd" pointer. It results in a use after free. Delete them. Fixes: 2865d42c78a9 ("staging: r8712u: Add the new driver to the mainline kernel") Cc: stable <[email protected]> Reported-by: Zheng Wang <[email protected]> Signed-off-by: Dan Carpenter <[email protected]> Link: https://lore.kernel.org/r/Yw4ASqkYcUhUfoY2@kili Signed-off-by: Greg Kroah-Hartman <[email protected]>
2022-08-30Merge tag 'mhi-fixes-for-v6.0' of ↵Greg Kroah-Hartman1-3/+16
git://git.kernel.org/pub/scm/linux/kernel/git/mani/mhi into char-misc-linus Manivannan writes: "A single fix targeting the MHI host stack: - Since the commit 1227d2a20cd7 ("bus: mhi: host: Move IRQ allocation to controller registration phase"), the MHI context gets freed during mhi_unregister_controller(). But when the MHI IRQs are shared, the IRQ handler may get invoked during __free_irq() if CONFIG_DEBUG_SHIRQ is set. In that case, there will be a null pointer dereference because of trying to use the freed context struct. So for fixing the issue, let's check for the existence of the context struct at the start of the handler before handling the IRQ." * tag 'mhi-fixes-for-v6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/mani/mhi: bus: mhi: host: Fix up null pointer access in mhi_irq_handler
2022-08-30Merge tag 'peci-fixes-6.0' of ↵Greg Kroah-Hartman2-3/+2
git://git.kernel.org/pub/scm/linux/kernel/git/iwi/linux into char-misc-linus Iwona writes: "PECI fixes for v6.0 Two minor fixes: * cpu - Fix use-after-free in adev_release() * aspeed - Fix error check for platform_get_irq()" * tag 'peci-fixes-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/iwi/linux: peci: cpu: Fix use-after-free in adev_release() peci: aspeed: fix error check return value of platform_get_irq()
2022-08-30usb: cdns3: fix issue with rearming ISO OUT endpointPawel Laszczak1-0/+1
ISO OUT endpoint is enabled during queuing first usb request in transfer ring and disabled when TRBERR is reported by controller. After TRBERR and before next transfer added to TR driver must again reenable endpoint but does not. To solve this issue during processing TRBERR event driver must set the flag EP_UPDATE_EP_TRBADDR in priv_ep->flags field. Fixes: 7733f6c32e36 ("usb: cdns3: Add Cadence USB3 DRD Driver") cc: <[email protected]> Acked-by: Peter Chen <[email protected]> Signed-off-by: Pawel Laszczak <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2022-08-30usb: cdns3: fix incorrect handling TRB_SMM flag for ISOC transferPawel Laszczak1-1/+2
The TRB_SMM flag indicates that DMA has completed the TD service with this TRB. Usually it’s a last TRB in TD. In case of ISOC transfer for bInterval > 1 each ISOC transfer contains more than one TD associated with usb request (one TD per ITP). In such case the TRB_SMM flag will be set in every TD and driver will recognize the end of transfer after processing the first TD with TRB_SMM. In result driver stops updating request->actual and returns incorrect actual length. To fix this issue driver additionally must check TRB_CHAIN which is not used for isochronous transfers. Fixes: 249f0a25e8be ("usb: cdns3: gadget: handle sg list use case at completion correctly") cc: <[email protected]> Acked-by: Peter Chen <[email protected]> Signed-off-by: Pawel Laszczak <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2022-08-30usb: gadget: mass_storage: Fix cdrom data transfers on MAC-OSKrishna Kurapati1-2/+4
During cdrom emulation, the response to read_toc command must contain the cdrom address as the number of sectors (2048 byte sized blocks) represented either as an absolute value (when MSF bit is '0') or in terms of PMin/PSec/PFrame (when MSF bit is set to '1'). Incase of cdrom, the fsg_lun_open call sets the sector size to 2048 bytes. When MAC OS sends a read_toc request with MSF set to '1', the store_cdrom_address assumes that the address being provided is the LUN size represented in 512 byte sized blocks instead of 2048. It tries to modify the address further to convert it to 2048 byte sized blocks and store it in MSF format. This results in data transfer failures as the cdrom address being provided in the read_toc response is incorrect. Fixes: 3f565a363cee ("usb: gadget: storage: adapt logic block size to bound block devices") Cc: [email protected] Acked-by: Alan Stern <[email protected]> Signed-off-by: Krishna Kurapati <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2022-08-30media: mceusb: Use new usb_control_msg_*() routinesAlan Stern1-21/+14
Automatic kernel fuzzing led to a WARN about invalid pipe direction in the mceusb driver: ------------[ cut here ]------------ usb 6-1: BOGUS control dir, pipe 80000380 doesn't match bRequestType 40 WARNING: CPU: 0 PID: 2465 at drivers/usb/core/urb.c:410 usb_submit_urb+0x1326/0x1820 drivers/usb/core/urb.c:410 Modules linked in: CPU: 0 PID: 2465 Comm: kworker/0:2 Not tainted 5.19.0-rc4-00208-g69cb6c6556ad #1 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1.1 04/01/2014 Workqueue: usb_hub_wq hub_event RIP: 0010:usb_submit_urb+0x1326/0x1820 drivers/usb/core/urb.c:410 Code: 7c 24 40 e8 ac 23 91 fd 48 8b 7c 24 40 e8 b2 70 1b ff 45 89 e8 44 89 f1 4c 89 e2 48 89 c6 48 c7 c7 a0 30 a9 86 e8 48 07 11 02 <0f> 0b e9 1c f0 ff ff e8 7e 23 91 fd 0f b6 1d 63 22 83 05 31 ff 41 RSP: 0018:ffffc900032becf0 EFLAGS: 00010282 RAX: 0000000000000000 RBX: ffff8881100f3058 RCX: 0000000000000000 RDX: ffffc90004961000 RSI: ffff888114c6d580 RDI: fffff52000657d90 RBP: ffff888105ad90f0 R08: ffffffff812c3638 R09: 0000000000000000 R10: 0000000000000005 R11: ffffed1023504ef1 R12: ffff888105ad9000 R13: 0000000000000040 R14: 0000000080000380 R15: ffff88810ba96500 FS: 0000000000000000(0000) GS:ffff88811a800000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007ffe810bda58 CR3: 000000010b720000 CR4: 0000000000350ef0 Call Trace: <TASK> usb_start_wait_urb+0x101/0x4c0 drivers/usb/core/message.c:58 usb_internal_control_msg drivers/usb/core/message.c:102 [inline] usb_control_msg+0x31c/0x4a0 drivers/usb/core/message.c:153 mceusb_gen1_init drivers/media/rc/mceusb.c:1431 [inline] mceusb_dev_probe+0x258e/0x33f0 drivers/media/rc/mceusb.c:1807 The reason for the warning is clear enough; the driver sends an unusual read request on endpoint 0 but does not set the USB_DIR_IN bit in the bRequestType field. More importantly, the whole situation can be avoided and the driver simplified by converting it over to the relatively new usb_control_msg_recv() and usb_control_msg_send() routines. That's what this fix does. Link: https://lore.kernel.org/all/CAB7eexLLApHJwZfMQ=X-PtRhw0BgO+5KcSMS05FNUYejJXqtSA@mail.gmail.com/ Cc: Mauro Carvalho Chehab <[email protected]> Cc: [email protected] Reported-and-tested-by: Rondreis <[email protected]> Signed-off-by: Alan Stern <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2022-08-30USB: core: Prevent nested device-reset callsAlan Stern1-0/+10
Automatic kernel fuzzing revealed a recursive locking violation in usb-storage: ============================================ WARNING: possible recursive locking detected 5.18.0 #3 Not tainted -------------------------------------------- kworker/1:3/1205 is trying to acquire lock: ffff888018638db8 (&us_interface_key[i]){+.+.}-{3:3}, at: usb_stor_pre_reset+0x35/0x40 drivers/usb/storage/usb.c:230 but task is already holding lock: ffff888018638db8 (&us_interface_key[i]){+.+.}-{3:3}, at: usb_stor_pre_reset+0x35/0x40 drivers/usb/storage/usb.c:230 ... stack backtrace: CPU: 1 PID: 1205 Comm: kworker/1:3 Not tainted 5.18.0 #3 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1.1 04/01/2014 Workqueue: usb_hub_wq hub_event Call Trace: <TASK> __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106 print_deadlock_bug kernel/locking/lockdep.c:2988 [inline] check_deadlock kernel/locking/lockdep.c:3031 [inline] validate_chain kernel/locking/lockdep.c:3816 [inline] __lock_acquire.cold+0x152/0x3ca kernel/locking/lockdep.c:5053 lock_acquire kernel/locking/lockdep.c:5665 [inline] lock_acquire+0x1ab/0x520 kernel/locking/lockdep.c:5630 __mutex_lock_common kernel/locking/mutex.c:603 [inline] __mutex_lock+0x14f/0x1610 kernel/locking/mutex.c:747 usb_stor_pre_reset+0x35/0x40 drivers/usb/storage/usb.c:230 usb_reset_device+0x37d/0x9a0 drivers/usb/core/hub.c:6109 r871xu_dev_remove+0x21a/0x270 drivers/staging/rtl8712/usb_intf.c:622 usb_unbind_interface+0x1bd/0x890 drivers/usb/core/driver.c:458 device_remove drivers/base/dd.c:545 [inline] device_remove+0x11f/0x170 drivers/base/dd.c:537 __device_release_driver drivers/base/dd.c:1222 [inline] device_release_driver_internal+0x1a7/0x2f0 drivers/base/dd.c:1248 usb_driver_release_interface+0x102/0x180 drivers/usb/core/driver.c:627 usb_forced_unbind_intf+0x4d/0xa0 drivers/usb/core/driver.c:1118 usb_reset_device+0x39b/0x9a0 drivers/usb/core/hub.c:6114 This turned out not to be an error in usb-storage but rather a nested device reset attempt. That is, as the rtl8712 driver was being unbound from a composite device in preparation for an unrelated USB reset (that driver does not have pre_reset or post_reset callbacks), its ->remove routine called usb_reset_device() -- thus nesting one reset call within another. Performing a reset as part of disconnect processing is a questionable practice at best. However, the bug report points out that the USB core does not have any protection against nested resets. Adding a reset_in_progress flag and testing it will prevent such errors in the future. Link: https://lore.kernel.org/all/CAB7eexKUpvX-JNiLzhXBDWgfg2T9e9_0Tw4HQ6keN==voRbP0g@mail.gmail.com/ Cc: [email protected] Reported-and-tested-by: Rondreis <[email protected]> Signed-off-by: Alan Stern <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2022-08-30USB: gadget: Fix obscure lockdep violation for udc_mutexAlan Stern1-10/+16
A recent commit expanding the scope of the udc_lock mutex in the gadget core managed to cause an obscure and slightly bizarre lockdep violation. In abbreviated form: ====================================================== WARNING: possible circular locking dependency detected 5.19.0-rc7+ #12510 Not tainted ------------------------------------------------------ udevadm/312 is trying to acquire lock: ffff80000aae1058 (udc_lock){+.+.}-{3:3}, at: usb_udc_uevent+0x54/0xe0 but task is already holding lock: ffff000002277548 (kn->active#4){++++}-{0:0}, at: kernfs_seq_start+0x34/0xe0 which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #3 (kn->active#4){++++}-{0:0}:        lock_acquire+0x68/0x84        __kernfs_remove+0x268/0x380        kernfs_remove_by_name_ns+0x58/0xac        sysfs_remove_file_ns+0x18/0x24        device_del+0x15c/0x440 -> #2 (device_links_lock){+.+.}-{3:3}:        lock_acquire+0x68/0x84        __mutex_lock+0x9c/0x430        mutex_lock_nested+0x38/0x64        device_link_remove+0x3c/0xa0        _regulator_put.part.0+0x168/0x190        regulator_put+0x3c/0x54        devm_regulator_release+0x14/0x20 -> #1 (regulator_list_mutex){+.+.}-{3:3}:        lock_acquire+0x68/0x84        __mutex_lock+0x9c/0x430        mutex_lock_nested+0x38/0x64        regulator_lock_dependent+0x54/0x284        regulator_enable+0x34/0x80        phy_power_on+0x24/0x130        __dwc2_lowlevel_hw_enable+0x100/0x130        dwc2_lowlevel_hw_enable+0x18/0x40        dwc2_hsotg_udc_start+0x6c/0x2f0        gadget_bind_driver+0x124/0x1f4 -> #0 (udc_lock){+.+.}-{3:3}:        __lock_acquire+0x1298/0x20cc        lock_acquire.part.0+0xe0/0x230        lock_acquire+0x68/0x84        __mutex_lock+0x9c/0x430        mutex_lock_nested+0x38/0x64        usb_udc_uevent+0x54/0xe0 Evidently this was caused by the scope of udc_mutex being too large. The mutex is only meant to protect udc->driver along with a few other things. As far as I can tell, there's no reason for the mutex to be held while the gadget core calls a gadget driver's ->bind or ->unbind routine, or while a UDC is being started or stopped. (This accounts for link #1 in the chain above, where the mutex is held while the dwc2_hsotg_udc is started as part of driver probing.) Gadget drivers' ->disconnect callbacks are problematic. Even though usb_gadget_disconnect() will now acquire the udc_mutex, there's a window in usb_gadget_bind_driver() between the times when the mutex is released and the ->bind callback is invoked. If a disconnect occurred during that window, we could call the driver's ->disconnect routine before its ->bind routine. To prevent this from happening, it will be necessary to prevent a UDC from connecting while it has no gadget driver. This should be done already but it doesn't seem to be; currently usb_gadget_connect() has no check for this. Such a check will have to be added later. Some degree of mutual exclusion is required in soft_connect_store(), which can dereference udc->driver at arbitrary times since it is a sysfs callback. The solution here is to acquire the gadget's device lock rather than the udc_mutex. Since the driver core guarantees that the device lock is always held during driver binding and unbinding, this will make the accesses in soft_connect_store() mutually exclusive with any changes to udc->driver. Lastly, it turns out there is one place which should hold the udc_mutex but currently does not: The function_show() routine needs protection while it dereferences udc->driver. The missing lock and unlock calls are added. Link: https://lore.kernel.org/all/[email protected]/ Fixes: 2191c00855b0 ("USB: gadget: Fix use-after-free Read in usb_udc_uevent()") Cc: Felipe Balbi <[email protected]> Cc: [email protected] Reported-by: Marek Szyprowski <[email protected]> Tested-by: Marek Szyprowski <[email protected]> Signed-off-by: Alan Stern <[email protected]> Link: https://lore.kernel.org/r/YwkfhdxA/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2022-08-30usb: dwc2: fix wrong order of phy_power_on and phy_initHeiner Kallweit1-4/+4
Since 1599069a62c6 ("phy: core: Warn when phy_power_on is called before phy_init") the driver complains. In my case (Amlogic SoC) the warning is: phy phy-fe03e000.phy.2: phy_power_on was called before phy_init So change the order of the two calls. The same change has to be done to the order of phy_exit() and phy_power_off(). Fixes: 09a75e857790 ("usb: dwc2: refactor common low-level hw code to platform.c") Cc: [email protected] Acked-by: Minas Harutyunyan <[email protected]> Acked-by: Marek Szyprowski <[email protected]> Signed-off-by: Heiner Kallweit <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2022-08-30usb: gadget: udc-xilinx: replace memcpy with memcpy_toioPiyush Mehta1-8/+8
For ARM processor, unaligned access to device memory is not allowed. Method memcpy does not take care of alignment. USB detection failure with the unaligned address of memory access, with below kernel crash. To fix the unaligned address the kernel panic issue, replace memcpy with memcpy_toio method. Kernel crash: Unable to handle kernel paging request at virtual address ffff80000c05008a Mem abort info: ESR = 0x96000061 EC = 0x25: DABT (current EL), IL = 32 bits SET = 0, FnV = 0 EA = 0, S1PTW = 0 FSC = 0x21: alignment fault Data abort info: ISV = 0, ISS = 0x00000061 CM = 0, WnR = 1 swapper pgtable: 4k pages, 48-bit VAs, pgdp=000000000143b000 [ffff80000c05008a] pgd=100000087ffff003, p4d=100000087ffff003, pud=100000087fffe003, pmd=1000000800bcc003, pte=00680000a0010713 Internal error: Oops: 96000061 [#1] SMP Modules linked in: CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.15.19-xilinx-v2022.1 #1 Hardware name: ZynqMP ZCU102 Rev1.0 (DT) pstate: 200000c5 (nzCv daIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : __memcpy+0x30/0x260 lr : __xudc_ep0_queue+0xf0/0x110 sp : ffff800008003d00 x29: ffff800008003d00 x28: ffff800009474e80 x27: 00000000000000a0 x26: 0000000000000100 x25: 0000000000000012 x24: ffff000800bc8080 x23: 0000000000000001 x22: 0000000000000012 x21: ffff000800bc8080 x20: 0000000000000012 x19: ffff000800bc8080 x18: 0000000000000000 x17: ffff800876482000 x16: ffff800008004000 x15: 0000000000004000 x14: 00001f09785d0400 x13: 0103020101005567 x12: 0781400000000200 x11: 00000000c5672a10 x10: 00000000000008d0 x9 : ffff800009463cf0 x8 : ffff8000094757b0 x7 : 0201010055670781 x6 : 4000000002000112 x5 : ffff80000c05009a x4 : ffff000800a15012 x3 : ffff00080362ad80 x2 : 0000000000000012 x1 : ffff000800a15000 x0 : ffff80000c050088 Call trace: __memcpy+0x30/0x260 xudc_ep0_queue+0x3c/0x60 usb_ep_queue+0x38/0x44 composite_ep0_queue.constprop.0+0x2c/0xc0 composite_setup+0x8d0/0x185c configfs_composite_setup+0x74/0xb0 xudc_irq+0x570/0xa40 __handle_irq_event_percpu+0x58/0x170 handle_irq_event+0x60/0x120 handle_fasteoi_irq+0xc0/0x220 handle_domain_irq+0x60/0x90 gic_handle_irq+0x74/0xa0 call_on_irq_stack+0x2c/0x60 do_interrupt_handler+0x54/0x60 el1_interrupt+0x30/0x50 el1h_64_irq_handler+0x18/0x24 el1h_64_irq+0x78/0x7c arch_cpu_idle+0x18/0x2c do_idle+0xdc/0x15c cpu_startup_entry+0x28/0x60 rest_init+0xc8/0xe0 arch_call_rest_init+0x10/0x1c start_kernel+0x694/0x6d4 __primary_switched+0xa4/0xac Fixes: 1f7c51660034 ("usb: gadget: Add xilinx usb2 device support") Cc: [email protected] Reviewed-by: Linus Walleij <[email protected]> Signed-off-by: Piyush Mehta <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2022-08-30usb: typec: Remove retimers properlyHeikki Krogerus1-0/+1
Retimer device class is left dangling when the typec module is unloaded. Attempts to reload the module failed with warning: "sysfs: cannot create duplicate filename '/class/retimer'" Fixing the issue by unregistering the class properly. Fixes: ddaf8d96f93b ("usb: typec: Add support for retimers") Reviewed-by: Prashant Malani <[email protected]> Signed-off-by: Heikki Krogerus <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2022-08-30usb: dwc3: disable USB core PHY managementJohan Hovold1-0/+10
The dwc3 driver manages its PHYs itself so the USB core PHY management needs to be disabled. Use the struct xhci_plat_priv hack added by commits 46034a999c07 ("usb: host: xhci-plat: add platform data support") and f768e718911e ("usb: host: xhci-plat: add priv quirk for skip PHY initialization") to propagate the setting for now. Fixes: 4e88d4c08301 ("usb: add a flag to skip PHY initialization to struct usb_hcd") Fixes: 178a0bce05cb ("usb: core: hcd: integrate the PHY wrapper into the HCD core") Tested-by: Matthias Kaehlcke <[email protected]> Cc: stable <[email protected]> Reviewed-by: Matthias Kaehlcke <[email protected]> Signed-off-by: Johan Hovold <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2022-08-30usb: add quirks for Lenovo OneLink+ DockJean-Francois Le Fillatre1-0/+4
The Lenovo OneLink+ Dock contains two VL812 USB3.0 controllers: 17ef:1018 upstream 17ef:1019 downstream Those two controllers both have problems with some USB3.0 devices, particularly self-powered ones. Typical error messages include: Timeout while waiting for setup device command device not accepting address X, error -62 unable to enumerate USB device By process of elimination the controllers themselves were identified as the cause of the problem. Through trial and error the issue was solved by using USB_QUIRK_RESET_RESUME for both chips. Signed-off-by: Jean-Francois Le Fillatre <[email protected]> Cc: stable <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2022-08-30tty: n_gsm: avoid call of sleeping functions from atomic contextFedor Pchelkin1-29/+24
Syzkaller reports the following problem: BUG: sleeping function called from invalid context at kernel/printk/printk.c:2347 in_atomic(): 1, irqs_disabled(): 1, non_block: 0, pid: 1105, name: syz-executor423 3 locks held by syz-executor423/1105: #0: ffff8881468b9098 (&tty->ldisc_sem){++++}-{0:0}, at: tty_ldisc_ref_wait+0x22/0x90 drivers/tty/tty_ldisc.c:266 #1: ffff8881468b9130 (&tty->atomic_write_lock){+.+.}-{3:3}, at: tty_write_lock drivers/tty/tty_io.c:952 [inline] #1: ffff8881468b9130 (&tty->atomic_write_lock){+.+.}-{3:3}, at: do_tty_write drivers/tty/tty_io.c:975 [inline] #1: ffff8881468b9130 (&tty->atomic_write_lock){+.+.}-{3:3}, at: file_tty_write.constprop.0+0x2a8/0x8e0 drivers/tty/tty_io.c:1118 #2: ffff88801b06c398 (&gsm->tx_lock){....}-{2:2}, at: gsmld_write+0x5e/0x150 drivers/tty/n_gsm.c:2717 irq event stamp: 3482 hardirqs last enabled at (3481): [<ffffffff81d13343>] __get_reqs_available+0x143/0x2f0 fs/aio.c:946 hardirqs last disabled at (3482): [<ffffffff87d39722>] __raw_spin_lock_irqsave include/linux/spinlock_api_smp.h:108 [inline] hardirqs last disabled at (3482): [<ffffffff87d39722>] _raw_spin_lock_irqsave+0x52/0x60 kernel/locking/spinlock.c:159 softirqs last enabled at (3408): [<ffffffff87e01002>] asm_call_irq_on_stack+0x12/0x20 softirqs last disabled at (3401): [<ffffffff87e01002>] asm_call_irq_on_stack+0x12/0x20 Preemption disabled at: [<0000000000000000>] 0x0 CPU: 2 PID: 1105 Comm: syz-executor423 Not tainted 5.10.137-syzkaller #0 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.12.0-1 04/01/2014 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x107/0x167 lib/dump_stack.c:118 ___might_sleep.cold+0x1e8/0x22e kernel/sched/core.c:7304 console_lock+0x19/0x80 kernel/printk/printk.c:2347 do_con_write+0x113/0x1de0 drivers/tty/vt/vt.c:2909 con_write+0x22/0xc0 drivers/tty/vt/vt.c:3296 gsmld_write+0xd0/0x150 drivers/tty/n_gsm.c:2720 do_tty_write drivers/tty/tty_io.c:1028 [inline] file_tty_write.constprop.0+0x502/0x8e0 drivers/tty/tty_io.c:1118 call_write_iter include/linux/fs.h:1903 [inline] aio_write+0x355/0x7b0 fs/aio.c:1580 __io_submit_one fs/aio.c:1952 [inline] io_submit_one+0xf45/0x1a90 fs/aio.c:1999 __do_sys_io_submit fs/aio.c:2058 [inline] __se_sys_io_submit fs/aio.c:2028 [inline] __x64_sys_io_submit+0x18c/0x2f0 fs/aio.c:2028 do_syscall_64+0x33/0x40 arch/x86/entry/common.c:46 entry_SYSCALL_64_after_hwframe+0x61/0xc6 The problem happens in the following control flow: gsmld_write(...) spin_lock_irqsave(&gsm->tx_lock, flags) // taken a spinlock on TX data con_write(...) do_con_write(...) console_lock() might_sleep() // -> bug As far as console_lock() might sleep it should not be called with spinlock held. The patch replaces tx_lock spinlock with mutex in order to avoid the problem. Found by Linux Verification Center (linuxtesting.org) with Syzkaller. Fixes: 32dd59f96924 ("tty: n_gsm: fix race condition in gsmld_write()") Cc: stable <[email protected]> Signed-off-by: Fedor Pchelkin <[email protected]> Signed-off-by: Alexey Khoroshilov <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2022-08-30tty: n_gsm: replace kicktimer with delayed_workFedor Pchelkin1-8/+8
A kick_timer timer_list is replaced with kick_timeout delayed_work to be able to synchronize with mutexes as a prerequisite for the introduction of tx_mutex. Found by Linux Verification Center (linuxtesting.org) with Syzkaller. Fixes: c568f7086c6e ("tty: n_gsm: fix missing timer to handle stalled links") Cc: stable <[email protected]> Reviewed-by: Jiri Slaby <[email protected]> Suggested-by: Hillf Danton <[email protected]> Signed-off-by: Fedor Pchelkin <[email protected]> Signed-off-by: Alexey Khoroshilov <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2022-08-30tty: n_gsm: initialize more members at gsm_alloc_mux()Tetsuo Handa1-11/+6
syzbot is reporting use of uninitialized spinlock at gsmld_write() [1], for commit 32dd59f96924f45e ("tty: n_gsm: fix race condition in gsmld_write()") allows accessing gsm->tx_lock before gsm_activate_mux() initializes it. Since object initialization should be done right after allocation in order to avoid accessing uninitialized memory, move initialization of timer/work/waitqueue/spinlock from gsmld_open()/gsm_activate_mux() to gsm_alloc_mux(). Link: https://syzkaller.appspot.com/bug?extid=cf155def4e717db68a12 [1] Fixes: 32dd59f96924f45e ("tty: n_gsm: fix race condition in gsmld_write()") Reported-by: syzbot <[email protected]> Tested-by: syzbot <[email protected]> Cc: stable <[email protected]> Acked-by: Jiri Slaby <[email protected]> Signed-off-by: Tetsuo Handa <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2022-08-30tty: n_gsm: add sanity check for gsm->receive in gsm_receive_buf()Mazin Al Haddad1-1/+2
A null pointer dereference can happen when attempting to access the "gsm->receive()" function in gsmld_receive_buf(). Currently, the code assumes that gsm->recieve is only called after MUX activation. Since the gsmld_receive_buf() function can be accessed without the need to initialize the MUX, the gsm->receive() function will not be set and a NULL pointer dereference will occur. Fix this by avoiding the call to "gsm->receive()" in case the function is not initialized by adding a sanity check. Call Trace: <TASK> gsmld_receive_buf+0x1c2/0x2f0 drivers/tty/n_gsm.c:2861 tiocsti drivers/tty/tty_io.c:2293 [inline] tty_ioctl+0xa75/0x15d0 drivers/tty/tty_io.c:2692 vfs_ioctl fs/ioctl.c:51 [inline] __do_sys_ioctl fs/ioctl.c:870 [inline] __se_sys_ioctl fs/ioctl.c:856 [inline] __x64_sys_ioctl+0x193/0x200 fs/ioctl.c:856 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x63/0xcd Link: https://syzkaller.appspot.com/bug?id=bdf035c61447f8c6e0e6920315d577cb5cc35ac5 Fixes: 01aecd917114 ("tty: n_gsm: fix tty registration before control channel open") Cc: stable <[email protected]> Reported-and-tested-by: [email protected] Signed-off-by: Mazin Al Haddad <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2022-08-30tty: serial: atmel: Preserve previous USART mode if RS485 disabledSergiu Moga1-3/+1
Whenever the atmel_rs485_config() driver method would be called, the USART mode is reset to normal mode before even checking if RS485 flag is set, thus resulting in losing the previous USART mode in the case where the checking fails. Some tools, such as `linux-serial-test`, lead to the driver calling this method when doing the setup of the serial port: after setting the port mode (Hardware Flow Control, Normal Mode, RS485 Mode, etc.), `linux-serial-test` tries to enable/disable RS485 depending on the commandline arguments that were passed. Example of how this issue could reveal itself: When doing a serial communication with Hardware Flow Control through `linux-serial-test`, the tool would lead to the driver roughly doing the following: - set the corresponding bit to 1 (ATMEL_US_USMODE_HWHS bit in the ATMEL_US_MR register) through the atmel_set_termios() to enable Hardware Flow Control - disable RS485 through the atmel_config_rs485() method Thus, when the latter is called, the mode will be reset and the previously set bit is unset, leaving USART in normal mode instead of the expected Hardware Flow Control mode. This fix ensures that this reset is only done if the checking for RS485 succeeds and that the previous mode is preserved otherwise. Fixes: e8faff7330a35 ("ARM: 6092/1: atmel_serial: support for RS485 communications") Cc: stable <[email protected]> Reviewed-by: Ilpo Järvinen <[email protected]> Signed-off-by: Sergiu Moga <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2022-08-30tty: serial: lpuart: disable flow control while waiting for the transmit ↵Sherry Sun1-0/+1
engine to complete When the user initializes the uart port, and waits for the transmit engine to complete in lpuart32_set_termios(), if the UART TX fifo has dirty data and the UARTMODIR enable the flow control, the TX fifo may never be empty. So here we should disable the flow control first to make sure the transmit engin can complete. Fixes: 380c966c093e ("tty: serial: fsl_lpuart: add 32-bit register interface support") Cc: stable <[email protected]> Signed-off-by: Sherry Sun <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2022-08-30tty: Fix lookahead_buf crash with serdevVincent Whitchurch1-5/+9
Do not follow a NULL pointer if the tty_port_client_operations does not implement the ->lookahead_buf() callback, which is the case with serdev's ttyport. Reported-by: Hans de Goede <[email protected]> Fixes: 6bb6fa6908ebd3 ("tty: Implement lookahead to process XON/XOFF timely") Reviewed-by: Ilpo Järvinen <[email protected]> Signed-off-by: Vincent Whitchurch <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2022-08-30serial: fsl_lpuart: RS485 RTS polariy is inverseShenwei Wang1-2/+2
The setting of RS485 RTS polarity is inverse in the current driver. When the property of 'rs485-rts-active-low' is enabled in the dts node, the RTS signal should be LOW during sending. Otherwise, if there is no such a property, the RTS should be HIGH during sending. Fixes: 03895cf41d18 ("tty: serial: fsl_lpuart: Add support for RS-485") Cc: stable <[email protected]> Signed-off-by: Nicolas Diaz <[email protected]> Signed-off-by: Shenwei Wang <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2022-08-30vt: Clear selection before changing the fontHelge Deller1-4/+8
When changing the console font with ioctl(KDFONTOP) the new font size can be bigger than the previous font. A previous selection may thus now be outside of the new screen size and thus trigger out-of-bounds accesses to graphics memory if the selection is removed in vc_do_resize(). Prevent such out-of-memory accesses by dropping the selection before the various con_font_set() console handlers are called. Reported-by: [email protected] Cc: stable <[email protected]> Tested-by: Khalid Masum <[email protected]> Signed-off-by: Helge Deller <[email protected]> Link: https://lore.kernel.org/r/YuV9apZGNmGfjcor@p100 Signed-off-by: Greg Kroah-Hartman <[email protected]>
2022-08-30ARM: 9229/1: amba: Fix use-after-free in amba_read_periphid()Isaac Manjarres1-1/+7
After commit f2d3b9a46e0e ("ARM: 9220/1: amba: Remove deferred device addition"), it became possible for amba_read_periphid() to be invoked concurrently from two threads for a particular AMBA device. Consider the case where a thread (T0) is registering an AMBA driver, and searching for all of the devices it can match with on the AMBA bus. Suppose that another thread (T1) is executing the deferred probe work, and is searching through all of the AMBA drivers on the bus for a driver that matches a particular AMBA device. Assume that both threads begin operating on the same AMBA device and the device's peripheral ID is still unknown. In this scenario, the amba_match() function will be invoked for the same AMBA device by both threads, which means amba_read_periphid() can also be invoked by both threads, and both threads will be able to manipulate the AMBA device's pclk pointer without any synchronization. It's possible that one thread will initialize the pclk pointer, then the other thread will re-initialize it, overwriting the previous value, and both will race to free the same pclk, resulting in a use-after-free for whichever thread frees the pclk last. Add a lock per AMBA device to synchronize the handling with detecting the peripheral ID to avoid the use-after-free scenario. The following KFENCE bug report helped detect this problem: ================================================================== BUG: KFENCE: use-after-free read in clk_disable+0x14/0x34 Use-after-free read at 0x(ptrval) (in kfence-#19): clk_disable+0x14/0x34 amba_read_periphid+0xdc/0x134 amba_match+0x3c/0x84 __driver_attach+0x20/0x158 bus_for_each_dev+0x74/0xc0 bus_add_driver+0x154/0x1e8 driver_register+0x88/0x11c do_one_initcall+0x8c/0x2fc kernel_init_freeable+0x190/0x220 kernel_init+0x10/0x108 ret_from_fork+0x14/0x3c 0x0 kfence-#19: 0x(ptrval)-0x(ptrval), size=36, cache=kmalloc-64 allocated by task 8 on cpu 0 at 11.629931s: clk_hw_create_clk+0x38/0x134 amba_get_enable_pclk+0x10/0x68 amba_read_periphid+0x28/0x134 amba_match+0x3c/0x84 __device_attach_driver+0x2c/0xc4 bus_for_each_drv+0x80/0xd0 __device_attach+0xb0/0x1f0 bus_probe_device+0x88/0x90 deferred_probe_work_func+0x8c/0xc0 process_one_work+0x23c/0x690 worker_thread+0x34/0x488 kthread+0xd4/0xfc ret_from_fork+0x14/0x3c 0x0 freed by task 8 on cpu 0 at 11.630095s: amba_read_periphid+0xec/0x134 amba_match+0x3c/0x84 __device_attach_driver+0x2c/0xc4 bus_for_each_drv+0x80/0xd0 __device_attach+0xb0/0x1f0 bus_probe_device+0x88/0x90 deferred_probe_work_func+0x8c/0xc0 process_one_work+0x23c/0x690 worker_thread+0x34/0x488 kthread+0xd4/0xfc ret_from_fork+0x14/0x3c 0x0 Cc: Saravana Kannan <[email protected]> Cc: [email protected] Fixes: f2d3b9a46e0e ("ARM: 9220/1: amba: Remove deferred device addition") Reported-by: Guenter Roeck <[email protected]> Tested-by: Guenter Roeck <[email protected]> Signed-off-by: Isaac J. Manjarres <[email protected]> Signed-off-by: Russell King (Oracle) <[email protected]>
2022-08-30RDMA/hns: Remove the num_qpc_timer variableYixing Liu4-5/+3
The bt number of qpc_timer of HIP09 increases compared with that of HIP08. Therefore, qpc_timer_bt_num and num_qpc_timer do not match. As a result, the driver may fail to allocate qpc_timer. So the driver needs to uniquely uses qpc_timer_bt_num to represent the bt number of qpc_timer. Fixes: 0e40dc2f70cd ("RDMA/hns: Add timer allocation support for hip08") Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Yixing Liu <[email protected]> Signed-off-by: Wenpeng Liang <[email protected]> Signed-off-by: Leon Romanovsky <[email protected]>
2022-08-30RDMA/hns: Fix wrong fixed value of qp->rq.wqe_shiftWenpeng Liang1-5/+2
The value of qp->rq.wqe_shift of HIP08 is always determined by the number of sge. So delete the wrong branch. Fixes: cfc85f3e4b7f ("RDMA/hns: Add profile support for hip08 driver") Fixes: 926a01dc000d ("RDMA/hns: Add QP operations support for hip08 SoC") Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Wenpeng Liang <[email protected]> Signed-off-by: Leon Romanovsky <[email protected]>
2022-08-30RDMA/hns: Fix supported page sizeChengchang Tang1-1/+1
The supported page size for hns is (4K, 128M), not (4K, 2G). Fixes: cfc85f3e4b7f ("RDMA/hns: Add profile support for hip08 driver") Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Chengchang Tang <[email protected]> Signed-off-by: Wenpeng Liang <[email protected]> Signed-off-by: Leon Romanovsky <[email protected]>
2022-08-29hwmon: (gpio-fan) Fix array out of bounds accessArmin Wolf1-0/+3
The driver does not check if the cooling state passed to gpio_fan_set_cur_state() exceeds the maximum cooling state as stored in fan_data->num_speeds. Since the cooling state is later used as an array index in set_fan_speed(), an array out of bounds access can occur. This can be exploited by setting the state of the thermal cooling device to arbitrary values, causing for example a kernel oops when unavailable memory is accessed this way. Example kernel oops: [ 807.987276] Unable to handle kernel paging request at virtual address ffffff80d0588064 [ 807.987369] Mem abort info: [ 807.987398] ESR = 0x96000005 [ 807.987428] EC = 0x25: DABT (current EL), IL = 32 bits [ 807.987477] SET = 0, FnV = 0 [ 807.987507] EA = 0, S1PTW = 0 [ 807.987536] FSC = 0x05: level 1 translation fault [ 807.987570] Data abort info: [ 807.987763] ISV = 0, ISS = 0x00000005 [ 807.987801] CM = 0, WnR = 0 [ 807.987832] swapper pgtable: 4k pages, 39-bit VAs, pgdp=0000000001165000 [ 807.987872] [ffffff80d0588064] pgd=0000000000000000, p4d=0000000000000000, pud=0000000000000000 [ 807.987961] Internal error: Oops: 96000005 [#1] PREEMPT SMP [ 807.987992] Modules linked in: cmac algif_hash aes_arm64 algif_skcipher af_alg bnep hci_uart btbcm bluetooth ecdh_generic ecc 8021q garp stp llc snd_soc_hdmi_codec brcmfmac vc4 brcmutil cec drm_kms_helper snd_soc_core cfg80211 snd_compress bcm2835_codec(C) snd_pcm_dmaengine syscopyarea bcm2835_isp(C) bcm2835_v4l2(C) sysfillrect v4l2_mem2mem bcm2835_mmal_vchiq(C) raspberrypi_hwmon sysimgblt videobuf2_dma_contig videobuf2_vmalloc fb_sys_fops videobuf2_memops rfkill videobuf2_v4l2 videobuf2_common i2c_bcm2835 snd_bcm2835(C) videodev snd_pcm snd_timer snd mc vc_sm_cma(C) gpio_fan uio_pdrv_genirq uio drm fuse drm_panel_orientation_quirks backlight ip_tables x_tables ipv6 [ 807.988508] CPU: 0 PID: 1321 Comm: bash Tainted: G C 5.15.56-v8+ #1575 [ 807.988548] Hardware name: Raspberry Pi 3 Model B Rev 1.2 (DT) [ 807.988574] pstate: 20000005 (nzCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 807.988608] pc : set_fan_speed.part.5+0x34/0x80 [gpio_fan] [ 807.988654] lr : gpio_fan_set_cur_state+0x34/0x50 [gpio_fan] [ 807.988691] sp : ffffffc008cf3bd0 [ 807.988710] x29: ffffffc008cf3bd0 x28: ffffff80019edac0 x27: 0000000000000000 [ 807.988762] x26: 0000000000000000 x25: 0000000000000000 x24: ffffff800747c920 [ 807.988787] x23: 000000000000000a x22: ffffff800369f000 x21: 000000001999997c [ 807.988854] x20: ffffff800369f2e8 x19: ffffff8002ae8080 x18: 0000000000000000 [ 807.988877] x17: 0000000000000000 x16: 0000000000000000 x15: 000000559e271b70 [ 807.988938] x14: 0000000000000000 x13: 0000000000000000 x12: 0000000000000000 [ 807.988960] x11: 0000000000000000 x10: ffffffc008cf3c20 x9 : ffffffcfb60c741c [ 807.989018] x8 : 000000000000000a x7 : 00000000ffffffc9 x6 : 0000000000000009 [ 807.989040] x5 : 000000000000002a x4 : 0000000000000000 x3 : ffffff800369f2e8 [ 807.989062] x2 : 000000000000e780 x1 : 0000000000000001 x0 : ffffff80d0588060 [ 807.989084] Call trace: [ 807.989091] set_fan_speed.part.5+0x34/0x80 [gpio_fan] [ 807.989113] gpio_fan_set_cur_state+0x34/0x50 [gpio_fan] [ 807.989199] cur_state_store+0x84/0xd0 [ 807.989221] dev_attr_store+0x20/0x38 [ 807.989262] sysfs_kf_write+0x4c/0x60 [ 807.989282] kernfs_fop_write_iter+0x130/0x1c0 [ 807.989298] new_sync_write+0x10c/0x190 [ 807.989315] vfs_write+0x254/0x378 [ 807.989362] ksys_write+0x70/0xf8 [ 807.989379] __arm64_sys_write+0x24/0x30 [ 807.989424] invoke_syscall+0x4c/0x110 [ 807.989442] el0_svc_common.constprop.3+0xfc/0x120 [ 807.989458] do_el0_svc+0x2c/0x90 [ 807.989473] el0_svc+0x24/0x60 [ 807.989544] el0t_64_sync_handler+0x90/0xb8 [ 807.989558] el0t_64_sync+0x1a0/0x1a4 [ 807.989579] Code: b9403801 f9402800 7100003f 8b35cc00 (b9400416) [ 807.989627] ---[ end trace 8ded4c918658445b ]--- Fix this by checking the cooling state and return an error if it exceeds the maximum cooling state. Tested on a Raspberry Pi 3. Fixes: b5cf88e46bad ("(gpio-fan): Add thermal control hooks") Signed-off-by: Armin Wolf <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Guenter Roeck <[email protected]>
2022-08-29Input: iforce - add support for Boeder Force Feedback WheelGreg Tulli1-0/+1
Add a new iforce_device entry to support the Boeder Force Feedback Wheel device. Signed-off-by: Greg Tulli <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Dmitry Torokhov <[email protected]>
2022-08-29soc: brcmstb: pm-arm: Fix refcount leak and __iomem leak bugsLiang He1-11/+39
In brcmstb_pm_probe(), there are two kinds of leak bugs: (1) we need to add of_node_put() when for_each__matching_node() breaks (2) we need to add iounmap() for each iomap in fail path Fixes: 0b741b8234c8 ("soc: bcm: brcmstb: Add support for S2/S3/S5 suspend states (ARM)") Signed-off-by: Liang He <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Florian Fainelli <[email protected]>
2022-08-29bus: mhi: host: Fix up null pointer access in mhi_irq_handlerQiang Yu1-3/+16
The irq handler for a shared IRQ ought to be prepared for running even now it's being freed. So let's check the pointer used by mhi_irq_handler to avoid null pointer access since it is probably released before freeing IRQ. Fixes: 1227d2a20cd7 ("bus: mhi: host: Move IRQ allocation to controller registration phase") Signed-off-by: Qiang Yu <[email protected]> Reviewed-by: Manivannan Sadhasivam <[email protected]> Tested-by: Kalle Valo <[email protected]> Link: https://lore.kernel.org/r/[email protected] [mani: added fixes tag] Signed-off-by: Manivannan Sadhasivam <[email protected]>
2022-08-29drm/i915: Skip wm/ddb readout for disabled pipesVille Syrjälä1-1/+7
The stuff programmed into the wm/ddb registers of planes on disabled pipes doesn't matter. So during readout just leave our software state tracking for those zeroed. This should avoid us trying too hard to clean up after whatever mess the VBIOS/GOP left in there. The actual hardware state will get cleaned up if/when we enable the pipe anyway. Cc: [email protected] Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/5711 Signed-off-by: Ville Syrjälä <[email protected]> Link: https://patchwork.freedesktop.org/patch/msgid/[email protected] Reviewed-by: Stanislav Lisovskiy <[email protected]> (cherry picked from commit b183db8f4783ca2efc9b47734f15aad9477a108a) Signed-off-by: Rodrigo Vivi <[email protected]>
2022-08-29drm/i915/glk: ECS Liva Q2 needs GLK HDMI port timing quirkDiego Santa Cruz1-0/+3
The quirk added in upstream commit 90c3e2198777 ("drm/i915/glk: Add Quirk for GLK NUC HDMI port issues.") is also required on the ECS Liva Q2. Note: Would be nicer to figure out the extra delay required for the retimer without quirks, however don't know how to check for that. Cc: [email protected] Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/1326 Signed-off-by: Diego Santa Cruz <[email protected]> Reviewed-by: Ville Syrjälä <[email protected]> Signed-off-by: Jani Nikula <[email protected]> Link: https://patchwork.freedesktop.org/patch/msgid/[email protected] (cherry picked from commit 08e9505fa8f9aa00072a47b6f234d89b6b27a89c) Signed-off-by: Rodrigo Vivi <[email protected]>
2022-08-29drm/i915: fix null pointer dereferenceŁukasz Bartosik1-7/+9
Asus chromebook CX550 crashes during boot on v5.17-rc1 kernel. The root cause is null pointer defeference of bi_next in tgl_get_bw_info() in drivers/gpu/drm/i915/display/intel_bw.c. BUG: kernel NULL pointer dereference, address: 000000000000002e PGD 0 P4D 0 Oops: 0002 [#1] PREEMPT SMP NOPTI CPU: 0 PID: 1 Comm: swapper/0 Tainted: G U 5.17.0-rc1 Hardware name: Google Delbin/Delbin, BIOS Google_Delbin.13672.156.3 05/14/2021 RIP: 0010:tgl_get_bw_info+0x2de/0x510 ... [ 2.554467] Call Trace: [ 2.554467] <TASK> [ 2.554467] intel_bw_init_hw+0x14a/0x434 [ 2.554467] ? _printk+0x59/0x73 [ 2.554467] ? _dev_err+0x77/0x91 [ 2.554467] i915_driver_hw_probe+0x329/0x33e [ 2.554467] i915_driver_probe+0x4c8/0x638 [ 2.554467] i915_pci_probe+0xf8/0x14e [ 2.554467] ? _raw_spin_unlock_irqrestore+0x12/0x2c [ 2.554467] pci_device_probe+0xaa/0x142 [ 2.554467] really_probe+0x13f/0x2f4 [ 2.554467] __driver_probe_device+0x9e/0xd3 [ 2.554467] driver_probe_device+0x24/0x7c [ 2.554467] __driver_attach+0xba/0xcf [ 2.554467] ? driver_attach+0x1f/0x1f [ 2.554467] bus_for_each_dev+0x8c/0xc0 [ 2.554467] bus_add_driver+0x11b/0x1f7 [ 2.554467] driver_register+0x60/0xea [ 2.554467] ? mipi_dsi_bus_init+0x16/0x16 [ 2.554467] i915_init+0x2c/0xb9 [ 2.554467] ? mipi_dsi_bus_init+0x16/0x16 [ 2.554467] do_one_initcall+0x12e/0x2b3 [ 2.554467] do_initcall_level+0xd6/0xf3 [ 2.554467] do_initcalls+0x4e/0x79 [ 2.554467] kernel_init_freeable+0xed/0x14d [ 2.554467] ? rest_init+0xc1/0xc1 [ 2.554467] kernel_init+0x1a/0x120 [ 2.554467] ret_from_fork+0x1f/0x30 [ 2.554467] </TASK> ... Kernel panic - not syncing: Fatal exception Fixes: c64a9a7c05be ("drm/i915: Update memory bandwidth formulae") Signed-off-by: Łukasz Bartosik <[email protected]> Reviewed-by: Radhakrishna Sripada <[email protected]> Signed-off-by: Jani Nikula <[email protected]> Link: https://patchwork.freedesktop.org/patch/msgid/[email protected] (cherry picked from commit c247cd03898c4c43c3bce6d4014730403bc13032) Signed-off-by: Rodrigo Vivi <[email protected]>
2022-08-29drm/i915/backlight: Disable pps power hook for aux based backlightJouni Högander2-5/+8
Pps power hook seems to be problematic for backlight controlled via aux channel. Disable it for such cases. Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/3657 Cc: [email protected] Signed-off-by: Jouni Högander <[email protected]> Signed-off-by: Jani Nikula <[email protected]> Link: https://patchwork.freedesktop.org/patch/msgid/[email protected] (cherry picked from commit 869e3bb7acb59d88c1226892136661810e8223a4) Signed-off-by: Rodrigo Vivi <[email protected]>
2022-08-29drm/i915/display: avoid warnings when registering dual panel backlightArun R Murthy1-14/+12
Commit 20f85ef89d94 ("drm/i915/backlight: use unique backlight device names") added support for multiple backlight devices on dual panel systems, but did so with error handling on -EEXIST from backlight_device_register(). Unfortunately, that triggered a warning in dmesg all the way down from sysfs_add_file_mode_ns() and sysfs_warn_dup(). Instead of optimistically always attempting to register with the default name ("intel_backlight", which we have to retain for backward compatibility), check if a backlight device with the name exists first, and, if so, use the card and connector based name. v2: reworked on top of the patch commit 20f85ef89d94 ("drm/i915/backlight: use unique backlight device names") v3: fixed the ref count leak(Jani N) Fixes: 20f85ef89d94 ("drm/i915/backlight: use unique backlight device names") Signed-off-by: Arun R Murthy <[email protected]> Signed-off-by: Jani Nikula <[email protected]> Link: https://patchwork.freedesktop.org/patch/msgid/[email protected] (cherry picked from commit 4234ea30051200fc6016de10e4d58369e60b38f1) Signed-off-by: Rodrigo Vivi <[email protected]>
2022-08-29drm/i915/dsi: fix dual-link DSI backlight and CABC ports for display 11+Jani Nikula1-4/+6
The VBT dual-link DSI backlight and CABC still use ports A and C, both in Bspec and code, while display 11+ DSI only supports ports A and B. Assume port C actually means port B for display 11+ when parsing VBT. Bspec: 20154 Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/6476 Cc: [email protected] Signed-off-by: Jani Nikula <[email protected]> Reviewed-by: Stanislav Lisovskiy <[email protected]> Link: https://patchwork.freedesktop.org/patch/msgid/8c462718bcc7b36a83e09d0a5eef058b6bc8b1a2.1660664162.git.jani.nikula@intel.com (cherry picked from commit ab55165d73a444606af1530cd0d6448b04370f68) Signed-off-by: Rodrigo Vivi <[email protected]>
2022-08-29drm/i915/dsi: filter invalid backlight and CABC portsJani Nikula2-0/+14
Avoid using ports that aren't initialized in case the VBT backlight or CABC ports have invalid values. This fixes a NULL pointer dereference of intel_dsi->dsi_hosts[port] in such cases. Cc: [email protected] Signed-off-by: Jani Nikula <[email protected]> Reviewed-by: Stanislav Lisovskiy <[email protected]> Link: https://patchwork.freedesktop.org/patch/msgid/b0f4f087866257d280eb97d6bcfcefd109cc5fa2.1660664162.git.jani.nikula@intel.com (cherry picked from commit f4a6c7a454a6e71c5ccf25af82694213a9784013) Signed-off-by: Rodrigo Vivi <[email protected]>
2022-08-29drm/i915/guc: clear stalled request after a resetDaniele Ceraolo Spurio1-0/+7
If the GuC CTs are full and we need to stall the request submission while waiting for space, we save the stalled request and where the stall occurred; when the CTs have space again we pick up the request submission from where we left off. If a full GT reset occurs, the state of all contexts is cleared and all non-guilty requests are unsubmitted, therefore we need to restart the stalled request submission from scratch. To make sure that we do so, clear the saved request after a reset. Fixes note: the patch that introduced the bug is in 5.15, but no officially supported platform had GuC submission enabled by default in that kernel, so the backport to that particular version (and only that one) can potentially be skipped. Fixes: 925dc1cf58ed ("drm/i915/guc: Implement GuC submission tasklet") Signed-off-by: Daniele Ceraolo Spurio <[email protected]> Cc: Matthew Brost <[email protected]> Cc: John Harrison <[email protected]> Cc: <[email protected]> # v5.15+ Reviewed-by: John Harrison <[email protected]> Link: https://patchwork.freedesktop.org/patch/msgid/[email protected] (cherry picked from commit f922fbb0f2ad1fd3e3186f39c46673419e6d9281) Signed-off-by: Rodrigo Vivi <[email protected]>
2022-08-29drm/i915/ttm: fix CCS handlingMatthew Auld1-23/+21
Crucible + recent Mesa seems to sometimes hit: GEM_BUG_ON(num_ccs_blks > NUM_CCS_BLKS_PER_XFER) And it looks like we can also trigger this with gem_lmem_swapping, if we modify the test to use slightly larger object sizes. Looking closer it looks like we have the following issues in migrate_copy(): - We are using plain integer in various places, which we can easily overflow with a large object. - We pass the entire object size (when the src is lmem) into emit_pte() and then try to copy it, which doesn't work, since we only have a few fixed sized windows in which to map the pages and perform the copy. With an object > 8M we therefore aren't properly copying the pages. And then with an object > 64M we trigger the GEM_BUG_ON(num_ccs_blks > NUM_CCS_BLKS_PER_XFER). So it looks like our copy handling for any object > 8M (which is our CHUNK_SZ) is currently broken on DG2. Fixes: da0595ae91da ("drm/i915/migrate: Evict and restore the flatccs capable lmem obj") Testcase: igt@gem_lmem_swapping Signed-off-by: Matthew Auld <[email protected]> Cc: Thomas Hellström <[email protected]> Cc: Ramalingam C <[email protected]> Reviewed-by: Ramalingam C<[email protected]> Link: https://patchwork.freedesktop.org/patch/msgid/[email protected] (cherry picked from commit 8676145eb2f53a9940ff70910caf0125bd8a4bc2) Signed-off-by: Rodrigo Vivi <[email protected]>
2022-08-29Merge tag 'gvt-fixes-2022-08-22' of https://github.com/intel/gvt-linux into ↵Rodrigo Vivi5-7/+8
drm-intel-fixes gvt-fixes-2022-08-22 - CometLake regression fix in mmio table rework (Alex) - misc kernel doc and typo fixes Signed-off-by: Rodrigo Vivi <[email protected]> From: Zhenyu Wang <[email protected]> Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
2022-08-29USB: serial: option: add support for Cinterion MV32-WA/WB RmNet modeSlark Xiao1-0/+6
We added PIDs for MV32-WA/WB MBIM mode before, now we need to add support for RmNet mode. Test evidence as below: T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=03 Dev#= 3 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=1e2d ProdID=00f3 Rev=05.04 S: Manufacturer=Cinterion S: Product=Cinterion PID 0x00F3 USB Mobile Broadband S: SerialNumber=d7b4be8d C: #Ifs= 4 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#=0x0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan I: If#=0x1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option I: If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option I: If#=0x3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=03 Dev#= 10 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=1e2d ProdID=00f4 Rev=05.04 S: Manufacturer=Cinterion S: Product=Cinterion PID 0x00F4 USB Mobile Broadband S: SerialNumber=d095087d C: #Ifs= 4 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#=0x0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan I: If#=0x1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option I: If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option I: If#=0x3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option Signed-off-by: Slark Xiao <[email protected]> [ johan: sort entries ] Cc: [email protected] Signed-off-by: Johan Hovold <[email protected]>
2022-08-29USB: serial: ftdi_sio: add Omron CS1W-CIF31 device idNiek Nooijens2-0/+8
works perfectly with: modprobe ftdi_sio echo "0590 00b2" | tee /sys/module/ftdi_sio/drivers/usb-serial\:ftdi_sio/new_id > /dev/null but doing this every reboot is a pain in the ass. Signed-off-by: Niek Nooijens <[email protected]> Cc: [email protected] Signed-off-by: Johan Hovold <[email protected]>
2022-08-29USB: serial: option: add Quectel EM060K modemYonglin Tan1-0/+4
Add usb product id entry for the Quectel EM060K module. "MBIM mode": DIAG + NMEA + AT + MODEM + MBIM + QDSS T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 8 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=2c7c ProdID=030b Rev= 5.04 S: Manufacturer=Quectel S: Product=EM060K-GL S: SerialNumber=89fb57db C:* #Ifs= 7 Cfg#= 1 Atr=a0 MxPwr=500mA A: FirstIf#= 8 IfCount= 2 Cls=02(comm.) Sub=0e Prot=00 I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=40 Driver=option E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 8 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=0e Prot=00 Driver=cdc_mbim E: Ad=88(I) Atr=03(Int.) MxPS= 64 Ivl=32ms I: If#= 9 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim I:* If#= 9 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim E: Ad=8e(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=0f(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#=12 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=70 Driver=(none) E: Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms Signed-off-by: Yonglin Tan <[email protected]> [ johan: mention QDSS port and sort entries ] Cc: [email protected] Signed-off-by: Johan Hovold <[email protected]>
2022-08-29net: Use u64_stats_fetch_begin_irq() for stats fetch.Sebastian Andrzej Siewior9-42/+42
On 32bit-UP u64_stats_fetch_begin() disables only preemption. If the reader is in preemptible context and the writer side (u64_stats_update_begin*()) runs in an interrupt context (IRQ or softirq) then the writer can update the stats during the read operation. This update remains undetected. Use u64_stats_fetch_begin_irq() to ensure the stats fetch on 32bit-UP are not interrupted by a writer. 32bit-SMP remains unaffected by this change. Cc: "David S. Miller" <[email protected]> Cc: Catherine Sullivan <[email protected]> Cc: David Awogbemila <[email protected]> Cc: Dimitris Michailidis <[email protected]> Cc: Eric Dumazet <[email protected]> Cc: Hans Ulli Kroll <[email protected]> Cc: Jakub Kicinski <[email protected]> Cc: Jeroen de Borst <[email protected]> Cc: Johannes Berg <[email protected]> Cc: Linus Walleij <[email protected]> Cc: Paolo Abeni <[email protected]> Cc: Simon Horman <[email protected]> Cc: [email protected] Cc: [email protected] Cc: [email protected] Cc: [email protected] Cc: [email protected] Signed-off-by: Sebastian Andrzej Siewior <[email protected]> Reviewed-by: Simon Horman <[email protected]> Signed-off-by: David S. Miller <[email protected]>