| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Commit 3559d81e76bf ("r8169: simplify rtl_hw_start_8169") changed order of
two register writes:
1) Caused RxConfig to be written before TX / RX is enabled,
2) Caused TxConfig to be written before TX / RX is enabled.
At least on XIDs 10000000 ("RTL8169sb/8110sb") and
18000000 ("RTL8169sc/8110sc") such writes are ignored by the chip, leaving
values in these registers intact.
Change 1) was reverted by
commit 05212ba8132b42 ("r8169: set RxConfig after tx/rx is enabled for RTL8169sb/8110sb devices"),
however change 2) wasn't.
In practice, this caused TxConfig's "InterFrameGap time" and "Max DMA Burst
Size per Tx DMA Burst" bits to be zero dramatically reducing TX performance
(in my tests it dropped from around 500Mbps to around 50Mbps).
This patch fixes the issue by moving TxConfig register write a bit later in
the code so it happens after TX / RX is already enabled.
Fixes: 05212ba8132b42 ("r8169: set RxConfig after tx/rx is enabled for RTL8169sb/8110sb devices")
Signed-off-by: Maciej S. Szmigiero <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Pull MD fixes from Shaohua Li:
- Fix a locking issue for md-cluster (Guoqing)
- Fix a sync crash for raid10 (Ni)
- Fix a reshape bug with raid5 cache enabled (me)
* tag 'md/4.19-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
md-cluster: release RESYNC lock after the last resync message
RAID10 BUG_ON in raise_barrier when force is true and conf->barrier is 0
md/raid5-cache: disable reshape completely
|
|
Pull ceph fixes from Ilya Dryomov:
"Two rbd patches to complete support for images within namespaces that
went into -rc1 and a use-after-free fix.
The rbd changes have been sitting in a branch for quite a while but
couldn't be included into the -rc1 pull request because of a pending
wire protocol backwards compatibility fixup that only got committed
early this week"
* tag 'ceph-for-4.19-rc3' of https://github.com/ceph/ceph-client:
rbd: support cloning across namespaces
rbd: factor out get_parent_info()
ceph: avoid a use-after-free in ceph_destroy_options()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These fix a regression from the 4.18 cycle in the ACPI driver for
Intel SoCs (LPSS) and prevent dmi_check_system() from being called on
non-x86 systems in the ACPI core.
Specifics:
- Fix a power management regression in the ACPI driver for Intel SoCs
(LPSS) introduced by a system-wide suspend/resume fix during the
4.18 cycle (Zhang Rui).
- Prevent dmi_check_system() from being called on non-x86 systems in
the ACPI core (Jean Delvare)"
* tag 'acpi-4.19-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / LPSS: Force LPSS quirks on boot
ACPI / bus: Only call dmi_check_system() on X86
|
|
Merge ACPI core fix to avoid calling dmi_check_system() on non-x86.
* acpi-bus:
ACPI / bus: Only call dmi_check_system() on X86
|
|
Pull drm fixes from Dave Airlie:
"Seems to have been overly quiet this week so I expect next week will
be more stuff, just one pull from Rodrigo with i915 fixes in it.
Quoting Rodrigo:
'The critical fix here on display side is the DP MST regression one.
But this pull also include fixes for DP SST, small VDSC register
fix and GVT's bucked with "BXT fixes, two guest warning fixes,
dmabuf format mod fix and one for recent multiple VM timeout
failure'."
* tag 'drm-fixes-2018-09-07' of git://anongit.freedesktop.org/drm/drm:
drm/i915/dp_mst: Fix enabling pipe clock for all streams
drm/i915/dsc: Fix PPS register definition macros for 2nd VDSC engine
drm/i915: Re-apply "Perform link quality check, unconditionally during long pulse"
drm/i915/gvt: Give new born vGPU higher scheduling chance
drm/i915/gvt: Fix drm_format_mod value for vGPU plane
drm/i915/gvt: move intel_runtime_pm_get out of spin_lock in stop_schedule
drm/i915/gvt: Handle GEN9_WM_CHICKEN3 with F_CMD_ACCESS.
drm/i915/gvt: Make correct handling to vreg BXT_PHY_CTL_FAMILY
drm/i915/gvt: emulate gen9 dbuf ctl register access
|
|
Bump target version to reflect the documented fixes are available.
Also fix some code comments (typos and clarity).
Signed-off-by: Heinz Mauelshagen <[email protected]>
Signed-off-by: Mike Snitzer <[email protected]>
|
|
On fast devices such as NVMe, a flaw in rs_get_progress() results in
false target status output when userspace lvm2 requests leg rebuilds
(symptom of the failure is device health chars 'aaaaaaaa' instead of
expected 'aAaAAAAA' causing lvm2 to fail).
The correct sync action state definitions already exist in
decipher_sync_action() so fix rs_get_progress() to use it.
Change decipher_sync_action() to return an enum rather than a string for
the sync states and call it from rs_get_progress(). Introduce
sync_str() to translate from enum to the string that is needed by
raid_status().
Signed-off-by: Heinz Mauelshagen <[email protected]>
Signed-off-by: Mike Snitzer <[email protected]>
|
|
Update superblock when particular devices are requested via rebuild
(e.g. lvconvert --replace ...) to avoid spurious failure with the "New
device injected into existing raid set without 'delta_disks' or
'rebuild' parameter specified" error message.
Signed-off-by: Heinz Mauelshagen <[email protected]>
Signed-off-by: Mike Snitzer <[email protected]>
|
|
When initiating a stripe adding reshape, a deadlock between
md_stop_writes() waiting for the sync thread to stop and the running
sync thread waiting for inactive stripes occurs (this frequently happens
on single-core but rarely on multi-core systems).
Fix this deadlock by setting MD_RECOVERY_WAIT to have the main MD
resynchronization thread worker (md_do_sync()) bail out when initiating
the reshape via constructor arguments.
Signed-off-by: Heinz Mauelshagen <[email protected]>
Signed-off-by: Mike Snitzer <[email protected]>
|
|
Pull block fixes from Jens Axboe:
"Small collection of fixes that should go into this release. This
contains:
- Small series that fixes a race between blkcg teardown and writeback
(Dennis Zhou)
- Fix disallowing invalid block size settings from the nbd ioctl (me)
- BFQ fix for a use-after-free on last release of a bfqg (Konstantin
Khlebnikov)
- Fix for the "don't warn for flush" fix (Mikulas)"
* tag 'for-linus-20180906' of git://git.kernel.dk/linux-block:
block: bfq: swap puts in bfqg_and_blkg_put
block: don't warn when doing fsync on read-only devices
nbd: don't allow invalid blocksize settings
blkcg: use tryget logic when associating a blkg with a bio
blkcg: delay blkg destruction until after writeback has finished
Revert "blk-throttle: fix race between blkcg_bio_issue_check() and cgroup_rmdir()"
|
|
panels
Fixes eDP backlight issues on more recent laptops.
Signed-off-by: Ben Skeggs <[email protected]>
|
|
If a HPD pulse signalling the need to retrain the link occurs between
the KMS driver releasing the output and the supervisor interrupt that
finishes the teardown, it was possible get a NULL-ptr deref.
Avoid this by marking the link as inactive earlier.
Signed-off-by: Ben Skeggs <[email protected]>
|
|
We need to do this earlier to prevent aux channel timeouts in resume
paths on certain systems.
Signed-off-by: Ben Skeggs <[email protected]>
|
|
Signed-off-by: Ben Skeggs <[email protected]>
|
|
This Falcon application doesn't appear to be present on some newer
systems, so let's not fail init if we can't find it.
TBD: is there a way to determine whether it *should* be there?
Signed-off-by: Ben Skeggs <[email protected]>
|
|
Fixes oopses in certain failure paths.
Signed-off-by: Ben Skeggs <[email protected]>
|
|
The NV_ERROR macro requires drm->client to be initialised, which it may not
be at this stage of the init process.
Signed-off-by: Ben Skeggs <[email protected]>
|
|
It looks like that when we moved over to using
drm_connector_for_each_possible_encoder() in nouveau, that one rather
important part of this function got dropped by accident:
/* Right v here */
for (i = 0; nv_encoder = NULL, i < DRM_CONNECTOR_MAX_ENCODER; i++) {
int id = connector->encoder_ids[i];
if (id == 0)
break;
Since it's rather difficult to notice: the conditional in this loop is
actually:
nv_encoder = NULL, i < DRM_CONNECTOR_MAX_ENCODER
Meaning that all early breaks result in nv_encoder keeping it's value,
otherwise nv_encoder = NULL. Ugh.
Since this got dropped, nouveau_connector_ddc_detect() now returns an
encoder for every single connector, regardless of whether or not it's
detected:
[ 1780.056185] nouveau 0000:01:00.0: DRM: DDC responded, but no EDID for DP-2
So: fix this to ensure we only return an encoder if we actually found
one, and clean up the rest of the function while we're at it since it's
nearly impossible to read properly.
Changes since v1:
- Don't skip ddc probing for LVDS if we can't switch DDC through
vga-switcheroo, just do the DDC probing without calling
vga_switcheroo_lock_ddc() - skeggsb
Signed-off-by: Lyude Paul <[email protected]>
Cc: Ville Syrjälä <[email protected]>
Fixes: ddba766dd07e ("drm/nouveau: Use drm_connector_for_each_possible_encoder()")
Reviewed-by: Ville Syrjälä <[email protected]>
Signed-off-by: Ben Skeggs <[email protected]>
|
|
Currently, there's nothing in nouveau that actually cancels this work
struct. So, cancel it on suspend/unload. Otherwise, if we're unlucky
enough hpd_work might try to keep running up until the system is
suspended.
Signed-off-by: Lyude Paul <[email protected]>
Cc: [email protected]
Signed-off-by: Ben Skeggs <[email protected]>
|
|
On most systems with ACPI hotplugging support, it seems that we always
receive a hotplug event once we re-enable EC interrupts even if the GPU
hasn't even been resumed yet.
This can cause problems since even though we schedule hpd_work to handle
connector reprobing for us, hpd_work synchronizes on
pm_runtime_get_sync() to wait until the device is ready to perform
reprobing. Since runtime suspend/resume callbacks are disabled before
the PM core calls ->suspend(), any calls to pm_runtime_get_sync() during
this period will grab a runtime PM ref and return immediately with
-EACCES. Because we schedule hpd_work from our ACPI HPD handler, and
hpd_work synchronizes on pm_runtime_get_sync(), this causes us to launch
a connector reprobe immediately even if the GPU isn't actually resumed
just yet. This causes various warnings in dmesg and occasionally, also
prevents some displays connected to the dedicated GPU from coming back
up after suspend. Example:
usb 1-4: USB disconnect, device number 14
usb 1-4.1: USB disconnect, device number 15
WARNING: CPU: 0 PID: 838 at drivers/gpu/drm/nouveau/include/nvkm/subdev/i2c.h:170 nouveau_dp_detect+0x17e/0x370 [nouveau]
CPU: 0 PID: 838 Comm: kworker/0:6 Not tainted 4.17.14-201.Lyude.bz1477182.V3.fc28.x86_64 #1
Hardware name: LENOVO 20EQS64N00/20EQS64N00, BIOS N1EET77W (1.50 ) 03/28/2018
Workqueue: events nouveau_display_hpd_work [nouveau]
RIP: 0010:nouveau_dp_detect+0x17e/0x370 [nouveau]
RSP: 0018:ffffa15143933cf0 EFLAGS: 00010293
RAX: 0000000000000000 RBX: ffff8cb4f656c400 RCX: 0000000000000000
RDX: ffffa1514500e4e4 RSI: ffffa1514500e4e4 RDI: 0000000001009002
RBP: ffff8cb4f4a8a800 R08: ffffa15143933cfd R09: ffffa15143933cfc
R10: 0000000000000000 R11: 0000000000000000 R12: ffff8cb4fb57a000
R13: ffff8cb4fb57a000 R14: ffff8cb4f4a8f800 R15: ffff8cb4f656c418
FS: 0000000000000000(0000) GS:ffff8cb51f400000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f78ec938000 CR3: 000000073720a003 CR4: 00000000003606f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
? _cond_resched+0x15/0x30
nouveau_connector_detect+0x2ce/0x520 [nouveau]
? _cond_resched+0x15/0x30
? ww_mutex_lock+0x12/0x40
drm_helper_probe_detect_ctx+0x8b/0xe0 [drm_kms_helper]
drm_helper_hpd_irq_event+0xa8/0x120 [drm_kms_helper]
nouveau_display_hpd_work+0x2a/0x60 [nouveau]
process_one_work+0x187/0x340
worker_thread+0x2e/0x380
? pwq_unbound_release_workfn+0xd0/0xd0
kthread+0x112/0x130
? kthread_create_worker_on_cpu+0x70/0x70
ret_from_fork+0x35/0x40
Code: 4c 8d 44 24 0d b9 00 05 00 00 48 89 ef ba 09 00 00 00 be 01 00 00 00 e8 e1 09 f8 ff 85 c0 0f 85 b2 01 00 00 80 7c 24 0c 03 74 02 <0f> 0b 48 89 ef e8 b8 07 f8 ff f6 05 51 1b c8 ff 02 0f 84 72 ff
---[ end trace 55d811b38fc8e71a ]---
So, to fix this we attempt to grab a runtime PM reference in the ACPI
handler itself asynchronously. If the GPU is already awake (it will have
normal hotplugging at this point) or runtime PM callbacks are currently
disabled on the device, we drop our reference without updating the
autosuspend delay. We only schedule connector reprobes when we
successfully managed to queue up a resume request with our asynchronous
PM ref.
This also has the added benefit of preventing redundant connector
reprobes from ACPI while the GPU is runtime resumed!
Signed-off-by: Lyude Paul <[email protected]>
Cc: [email protected]
Cc: Karol Herbst <[email protected]>
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1477182#c41
Signed-off-by: Lyude Paul <[email protected]>
Signed-off-by: Ben Skeggs <[email protected]>
|
|
When probing a new MST device, it's not safe to make any assumptions
about it's current state. While most well mannered MST hubs will just
disable the branching unit on hotplug disconnects, this isn't enough to
save us from various other scenarios that might have resulted in
something writing to the MST branching unit before we got control of it.
This could happen if a previous probe we tried failed, if we're booting
in kexec context and the hub is still in the state the last kernel put
it in, etc.
Luckily; there is no reason we can't just reset the branching unit
every time we enable a new topology. So, fix this by resetting it on
enabling new topologies to ensure that we always start off with a clean,
unmodified topology state on MST sinks.
This fixes occasional hard-lockups on my P50's laptop dock (e.g. AUX
times out all DPCD trasactions) observed after multiple docks, undocks,
and module reloads.
Signed-off-by: Lyude Paul <[email protected]>
Cc: [email protected]
Cc: Karol Herbst <[email protected]>
Signed-off-by: Ben Skeggs <[email protected]>
|
|
Currently, nouveau will re-write the DP_MSTM_CTRL register for an MST
hub every time it receives a long HPD pulse on DP. This isn't actually
necessary and additionally, has some unintended side effects.
With the P50 I've got here, rewriting DP_MSTM_CTRL constantly seems to
make it rather likely (1 out of 5 times usually) that bringing up MST
with it's ThinkPad dock will fail and result in sideband messages timing
out in the middle. Afterwards, successive probes don't manage to get the
dock to communicate properly over MST sideband properly.
Many times sideband message timeouts from MST hubs are indicative of
either the source or the sink dropping an ESI event, which can cause
DRM's perspective of the topology's current state to go out of sync with
reality. While it's tough to really know for sure what's happening to
the dock, using userspace tools to write to DP_MSTM_CTRL in the middle
of the MST link probing process does appear to make things flaky. It's
possible that when we write to DP_MSTM_CTRL, the function that gets
triggered to respond in the dock's firmware temporarily puts it in a
state where it might end up not reporting an ESI to the source, or ends
up dropping a sideband message we sent it.
So, to fix this we make it so that when probing an MST topology, we
respect it's current state. If the dock's already enabled, we simply
read DP_MSTM_CTRL and disable the topology if it's value is not what we
expected. Otherwise, we perform the normal MST probing dance. We avoid
taking any action except if the state of the MST topology actually
changes.
This fixes MST sideband message timeouts and detection failures on my
P50 with its ThinkPad dock.
Signed-off-by: Lyude Paul <[email protected]>
Cc: [email protected]
Cc: Karol Herbst <[email protected]>
Signed-off-by: Ben Skeggs <[email protected]>
|
|
Again, this doesn't do anything. drm_kms_helper_poll_enable() will have
already been called in nouveau_display_init()
Signed-off-by: Lyude Paul <[email protected]>
Reviewed-by: Karol Herbst <[email protected]>
Acked-by: Daniel Vetter <[email protected]>
Cc: Lukas Wunner <[email protected]>
Signed-off-by: Ben Skeggs <[email protected]>
|
|
This won't do anything but potentially make us miss hotplugs. We already
call drm_kms_helper_poll_disable() in
nouveau_pmops_suspend()->nouveau_display_suspend()->nouveau_display_fini()
Signed-off-by: Lyude Paul <[email protected]>
Reviewed-by: Karol Herbst <[email protected]>
Acked-by: Daniel Vetter <[email protected]>
Cc: Lukas Wunner <[email protected]>
Signed-off-by: Ben Skeggs <[email protected]>
|
|
This doesn't do anything, drm_kms_helper_poll_enable() gets called in
nouveau_pmops_resume()->nouveau_display_resume()->nouveau_display_init()
already.
Signed-off-by: Lyude Paul <[email protected]>
Reviewed-by: Karol Herbst <[email protected]>
Acked-by: Daniel Vetter <[email protected]>
Cc: Lukas Wunner <[email protected]>
Signed-off-by: Ben Skeggs <[email protected]>
|
|
When we disable hotplugging on the GPU, we need to be able to
synchronize with each connector's hotplug interrupt handler before the
interrupt is finally disabled. This can be a problem however, since
nouveau_connector_detect() currently grabs a runtime power reference
when handling connector probing. This will deadlock the runtime suspend
handler like so:
[ 861.480896] INFO: task kworker/0:2:61 blocked for more than 120 seconds.
[ 861.483290] Tainted: G O 4.18.0-rc6Lyude-Test+ #1
[ 861.485158] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 861.486332] kworker/0:2 D 0 61 2 0x80000000
[ 861.487044] Workqueue: events nouveau_display_hpd_work [nouveau]
[ 861.487737] Call Trace:
[ 861.488394] __schedule+0x322/0xaf0
[ 861.489070] schedule+0x33/0x90
[ 861.489744] rpm_resume+0x19c/0x850
[ 861.490392] ? finish_wait+0x90/0x90
[ 861.491068] __pm_runtime_resume+0x4e/0x90
[ 861.491753] nouveau_display_hpd_work+0x22/0x60 [nouveau]
[ 861.492416] process_one_work+0x231/0x620
[ 861.493068] worker_thread+0x44/0x3a0
[ 861.493722] kthread+0x12b/0x150
[ 861.494342] ? wq_pool_ids_show+0x140/0x140
[ 861.494991] ? kthread_create_worker_on_cpu+0x70/0x70
[ 861.495648] ret_from_fork+0x3a/0x50
[ 861.496304] INFO: task kworker/6:2:320 blocked for more than 120 seconds.
[ 861.496968] Tainted: G O 4.18.0-rc6Lyude-Test+ #1
[ 861.497654] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 861.498341] kworker/6:2 D 0 320 2 0x80000080
[ 861.499045] Workqueue: pm pm_runtime_work
[ 861.499739] Call Trace:
[ 861.500428] __schedule+0x322/0xaf0
[ 861.501134] ? wait_for_completion+0x104/0x190
[ 861.501851] schedule+0x33/0x90
[ 861.502564] schedule_timeout+0x3a5/0x590
[ 861.503284] ? mark_held_locks+0x58/0x80
[ 861.503988] ? _raw_spin_unlock_irq+0x2c/0x40
[ 861.504710] ? wait_for_completion+0x104/0x190
[ 861.505417] ? trace_hardirqs_on_caller+0xf4/0x190
[ 861.506136] ? wait_for_completion+0x104/0x190
[ 861.506845] wait_for_completion+0x12c/0x190
[ 861.507555] ? wake_up_q+0x80/0x80
[ 861.508268] flush_work+0x1c9/0x280
[ 861.508990] ? flush_workqueue_prep_pwqs+0x1b0/0x1b0
[ 861.509735] nvif_notify_put+0xb1/0xc0 [nouveau]
[ 861.510482] nouveau_display_fini+0xbd/0x170 [nouveau]
[ 861.511241] nouveau_display_suspend+0x67/0x120 [nouveau]
[ 861.511969] nouveau_do_suspend+0x5e/0x2d0 [nouveau]
[ 861.512715] nouveau_pmops_runtime_suspend+0x47/0xb0 [nouveau]
[ 861.513435] pci_pm_runtime_suspend+0x6b/0x180
[ 861.514165] ? pci_has_legacy_pm_support+0x70/0x70
[ 861.514897] __rpm_callback+0x7a/0x1d0
[ 861.515618] ? pci_has_legacy_pm_support+0x70/0x70
[ 861.516313] rpm_callback+0x24/0x80
[ 861.517027] ? pci_has_legacy_pm_support+0x70/0x70
[ 861.517741] rpm_suspend+0x142/0x6b0
[ 861.518449] pm_runtime_work+0x97/0xc0
[ 861.519144] process_one_work+0x231/0x620
[ 861.519831] worker_thread+0x44/0x3a0
[ 861.520522] kthread+0x12b/0x150
[ 861.521220] ? wq_pool_ids_show+0x140/0x140
[ 861.521925] ? kthread_create_worker_on_cpu+0x70/0x70
[ 861.522622] ret_from_fork+0x3a/0x50
[ 861.523299] INFO: task kworker/6:0:1329 blocked for more than 120 seconds.
[ 861.523977] Tainted: G O 4.18.0-rc6Lyude-Test+ #1
[ 861.524644] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 861.525349] kworker/6:0 D 0 1329 2 0x80000000
[ 861.526073] Workqueue: events nvif_notify_work [nouveau]
[ 861.526751] Call Trace:
[ 861.527411] __schedule+0x322/0xaf0
[ 861.528089] schedule+0x33/0x90
[ 861.528758] rpm_resume+0x19c/0x850
[ 861.529399] ? finish_wait+0x90/0x90
[ 861.530073] __pm_runtime_resume+0x4e/0x90
[ 861.530798] nouveau_connector_detect+0x7e/0x510 [nouveau]
[ 861.531459] ? ww_mutex_lock+0x47/0x80
[ 861.532097] ? ww_mutex_lock+0x47/0x80
[ 861.532819] ? drm_modeset_lock+0x88/0x130 [drm]
[ 861.533481] drm_helper_probe_detect_ctx+0xa0/0x100 [drm_kms_helper]
[ 861.534127] drm_helper_hpd_irq_event+0xa4/0x120 [drm_kms_helper]
[ 861.534940] nouveau_connector_hotplug+0x98/0x120 [nouveau]
[ 861.535556] nvif_notify_work+0x2d/0xb0 [nouveau]
[ 861.536221] process_one_work+0x231/0x620
[ 861.536994] worker_thread+0x44/0x3a0
[ 861.537757] kthread+0x12b/0x150
[ 861.538463] ? wq_pool_ids_show+0x140/0x140
[ 861.539102] ? kthread_create_worker_on_cpu+0x70/0x70
[ 861.539815] ret_from_fork+0x3a/0x50
[ 861.540521]
Showing all locks held in the system:
[ 861.541696] 2 locks held by kworker/0:2/61:
[ 861.542406] #0: 000000002dbf8af5 ((wq_completion)"events"){+.+.}, at: process_one_work+0x1b3/0x620
[ 861.543071] #1: 0000000076868126 ((work_completion)(&drm->hpd_work)){+.+.}, at: process_one_work+0x1b3/0x620
[ 861.543814] 1 lock held by khungtaskd/64:
[ 861.544535] #0: 0000000059db4b53 (rcu_read_lock){....}, at: debug_show_all_locks+0x23/0x185
[ 861.545160] 3 locks held by kworker/6:2/320:
[ 861.545896] #0: 00000000d9e1bc59 ((wq_completion)"pm"){+.+.}, at: process_one_work+0x1b3/0x620
[ 861.546702] #1: 00000000c9f92d84 ((work_completion)(&dev->power.work)){+.+.}, at: process_one_work+0x1b3/0x620
[ 861.547443] #2: 000000004afc5de1 (drm_connector_list_iter){.+.+}, at: nouveau_display_fini+0x96/0x170 [nouveau]
[ 861.548146] 1 lock held by dmesg/983:
[ 861.548889] 2 locks held by zsh/1250:
[ 861.549605] #0: 00000000348e3cf6 (&tty->ldisc_sem){++++}, at: ldsem_down_read+0x37/0x40
[ 861.550393] #1: 000000007009a7a8 (&ldata->atomic_read_lock){+.+.}, at: n_tty_read+0xc1/0x870
[ 861.551122] 6 locks held by kworker/6:0/1329:
[ 861.551957] #0: 000000002dbf8af5 ((wq_completion)"events"){+.+.}, at: process_one_work+0x1b3/0x620
[ 861.552765] #1: 00000000ddb499ad ((work_completion)(¬ify->work)#2){+.+.}, at: process_one_work+0x1b3/0x620
[ 861.553582] #2: 000000006e013cbe (&dev->mode_config.mutex){+.+.}, at: drm_helper_hpd_irq_event+0x6c/0x120 [drm_kms_helper]
[ 861.554357] #3: 000000004afc5de1 (drm_connector_list_iter){.+.+}, at: drm_helper_hpd_irq_event+0x78/0x120 [drm_kms_helper]
[ 861.555227] #4: 0000000044f294d9 (crtc_ww_class_acquire){+.+.}, at: drm_helper_probe_detect_ctx+0x3d/0x100 [drm_kms_helper]
[ 861.556133] #5: 00000000db193642 (crtc_ww_class_mutex){+.+.}, at: drm_modeset_lock+0x4b/0x130 [drm]
[ 861.557864] =============================================
[ 861.559507] NMI backtrace for cpu 2
[ 861.560363] CPU: 2 PID: 64 Comm: khungtaskd Tainted: G O 4.18.0-rc6Lyude-Test+ #1
[ 861.561197] Hardware name: LENOVO 20EQS64N0B/20EQS64N0B, BIOS N1EET78W (1.51 ) 05/18/2018
[ 861.561948] Call Trace:
[ 861.562757] dump_stack+0x8e/0xd3
[ 861.563516] nmi_cpu_backtrace.cold.3+0x14/0x5a
[ 861.564269] ? lapic_can_unplug_cpu.cold.27+0x42/0x42
[ 861.565029] nmi_trigger_cpumask_backtrace+0xa1/0xae
[ 861.565789] arch_trigger_cpumask_backtrace+0x19/0x20
[ 861.566558] watchdog+0x316/0x580
[ 861.567355] kthread+0x12b/0x150
[ 861.568114] ? reset_hung_task_detector+0x20/0x20
[ 861.568863] ? kthread_create_worker_on_cpu+0x70/0x70
[ 861.569598] ret_from_fork+0x3a/0x50
[ 861.570370] Sending NMI from CPU 2 to CPUs 0-1,3-7:
[ 861.571426] NMI backtrace for cpu 6 skipped: idling at intel_idle+0x7f/0x120
[ 861.571429] NMI backtrace for cpu 7 skipped: idling at intel_idle+0x7f/0x120
[ 861.571432] NMI backtrace for cpu 3 skipped: idling at intel_idle+0x7f/0x120
[ 861.571464] NMI backtrace for cpu 5 skipped: idling at intel_idle+0x7f/0x120
[ 861.571467] NMI backtrace for cpu 0 skipped: idling at intel_idle+0x7f/0x120
[ 861.571469] NMI backtrace for cpu 4 skipped: idling at intel_idle+0x7f/0x120
[ 861.571472] NMI backtrace for cpu 1 skipped: idling at intel_idle+0x7f/0x120
[ 861.572428] Kernel panic - not syncing: hung_task: blocked tasks
So: fix this by making it so that normal hotplug handling /only/ happens
so long as the GPU is currently awake without any pending runtime PM
requests. In the event that a hotplug occurs while the device is
suspending or resuming, we can simply defer our response until the GPU
is fully runtime resumed again.
Changes since v4:
- Use a new trick I came up with using pm_runtime_get() instead of the
hackish junk we had before
Signed-off-by: Lyude Paul <[email protected]>
Reviewed-by: Karol Herbst <[email protected]>
Acked-by: Daniel Vetter <[email protected]>
Cc: [email protected]
Cc: Lukas Wunner <[email protected]>
Signed-off-by: Ben Skeggs <[email protected]>
|
|
It's true we can't resume the device from poll workers in
nouveau_connector_detect(). We can however, prevent the autosuspend
timer from elapsing immediately if it hasn't already without risking any
sort of deadlock with the runtime suspend/resume operations. So do that
instead of entirely avoiding grabbing a power reference.
Signed-off-by: Lyude Paul <[email protected]>
Reviewed-by: Karol Herbst <[email protected]>
Acked-by: Daniel Vetter <[email protected]>
Cc: [email protected]
Cc: Lukas Wunner <[email protected]>
Signed-off-by: Ben Skeggs <[email protected]>
|
|
Currently, nouveau uses the generic drm_fb_helper_output_poll_changed()
function provided by DRM as it's output_poll_changed callback.
Unfortunately however, this function doesn't grab runtime PM references
early enough and even if it did-we can't block waiting for the device to
resume in output_poll_changed() since it's very likely that we'll need
to grab the fb_helper lock at some point during the runtime resume
process. This currently results in deadlocking like so:
[ 246.669625] INFO: task kworker/4:0:37 blocked for more than 120 seconds.
[ 246.673398] Not tainted 4.18.0-rc5Lyude-Test+ #2
[ 246.675271] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 246.676527] kworker/4:0 D 0 37 2 0x80000000
[ 246.677580] Workqueue: events output_poll_execute [drm_kms_helper]
[ 246.678704] Call Trace:
[ 246.679753] __schedule+0x322/0xaf0
[ 246.680916] schedule+0x33/0x90
[ 246.681924] schedule_preempt_disabled+0x15/0x20
[ 246.683023] __mutex_lock+0x569/0x9a0
[ 246.684035] ? kobject_uevent_env+0x117/0x7b0
[ 246.685132] ? drm_fb_helper_hotplug_event.part.28+0x20/0xb0 [drm_kms_helper]
[ 246.686179] mutex_lock_nested+0x1b/0x20
[ 246.687278] ? mutex_lock_nested+0x1b/0x20
[ 246.688307] drm_fb_helper_hotplug_event.part.28+0x20/0xb0 [drm_kms_helper]
[ 246.689420] drm_fb_helper_output_poll_changed+0x23/0x30 [drm_kms_helper]
[ 246.690462] drm_kms_helper_hotplug_event+0x2a/0x30 [drm_kms_helper]
[ 246.691570] output_poll_execute+0x198/0x1c0 [drm_kms_helper]
[ 246.692611] process_one_work+0x231/0x620
[ 246.693725] worker_thread+0x214/0x3a0
[ 246.694756] kthread+0x12b/0x150
[ 246.695856] ? wq_pool_ids_show+0x140/0x140
[ 246.696888] ? kthread_create_worker_on_cpu+0x70/0x70
[ 246.697998] ret_from_fork+0x3a/0x50
[ 246.699034] INFO: task kworker/0:1:60 blocked for more than 120 seconds.
[ 246.700153] Not tainted 4.18.0-rc5Lyude-Test+ #2
[ 246.701182] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 246.702278] kworker/0:1 D 0 60 2 0x80000000
[ 246.703293] Workqueue: pm pm_runtime_work
[ 246.704393] Call Trace:
[ 246.705403] __schedule+0x322/0xaf0
[ 246.706439] ? wait_for_completion+0x104/0x190
[ 246.707393] schedule+0x33/0x90
[ 246.708375] schedule_timeout+0x3a5/0x590
[ 246.709289] ? mark_held_locks+0x58/0x80
[ 246.710208] ? _raw_spin_unlock_irq+0x2c/0x40
[ 246.711222] ? wait_for_completion+0x104/0x190
[ 246.712134] ? trace_hardirqs_on_caller+0xf4/0x190
[ 246.713094] ? wait_for_completion+0x104/0x190
[ 246.713964] wait_for_completion+0x12c/0x190
[ 246.714895] ? wake_up_q+0x80/0x80
[ 246.715727] ? get_work_pool+0x90/0x90
[ 246.716649] flush_work+0x1c9/0x280
[ 246.717483] ? flush_workqueue_prep_pwqs+0x1b0/0x1b0
[ 246.718442] __cancel_work_timer+0x146/0x1d0
[ 246.719247] cancel_delayed_work_sync+0x13/0x20
[ 246.720043] drm_kms_helper_poll_disable+0x1f/0x30 [drm_kms_helper]
[ 246.721123] nouveau_pmops_runtime_suspend+0x3d/0xb0 [nouveau]
[ 246.721897] pci_pm_runtime_suspend+0x6b/0x190
[ 246.722825] ? pci_has_legacy_pm_support+0x70/0x70
[ 246.723737] __rpm_callback+0x7a/0x1d0
[ 246.724721] ? pci_has_legacy_pm_support+0x70/0x70
[ 246.725607] rpm_callback+0x24/0x80
[ 246.726553] ? pci_has_legacy_pm_support+0x70/0x70
[ 246.727376] rpm_suspend+0x142/0x6b0
[ 246.728185] pm_runtime_work+0x97/0xc0
[ 246.728938] process_one_work+0x231/0x620
[ 246.729796] worker_thread+0x44/0x3a0
[ 246.730614] kthread+0x12b/0x150
[ 246.731395] ? wq_pool_ids_show+0x140/0x140
[ 246.732202] ? kthread_create_worker_on_cpu+0x70/0x70
[ 246.732878] ret_from_fork+0x3a/0x50
[ 246.733768] INFO: task kworker/4:2:422 blocked for more than 120 seconds.
[ 246.734587] Not tainted 4.18.0-rc5Lyude-Test+ #2
[ 246.735393] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 246.736113] kworker/4:2 D 0 422 2 0x80000080
[ 246.736789] Workqueue: events_long drm_dp_mst_link_probe_work [drm_kms_helper]
[ 246.737665] Call Trace:
[ 246.738490] __schedule+0x322/0xaf0
[ 246.739250] schedule+0x33/0x90
[ 246.739908] rpm_resume+0x19c/0x850
[ 246.740750] ? finish_wait+0x90/0x90
[ 246.741541] __pm_runtime_resume+0x4e/0x90
[ 246.742370] nv50_disp_atomic_commit+0x31/0x210 [nouveau]
[ 246.743124] drm_atomic_commit+0x4a/0x50 [drm]
[ 246.743775] restore_fbdev_mode_atomic+0x1c8/0x240 [drm_kms_helper]
[ 246.744603] restore_fbdev_mode+0x31/0x140 [drm_kms_helper]
[ 246.745373] drm_fb_helper_restore_fbdev_mode_unlocked+0x54/0xb0 [drm_kms_helper]
[ 246.746220] drm_fb_helper_set_par+0x2d/0x50 [drm_kms_helper]
[ 246.746884] drm_fb_helper_hotplug_event.part.28+0x96/0xb0 [drm_kms_helper]
[ 246.747675] drm_fb_helper_output_poll_changed+0x23/0x30 [drm_kms_helper]
[ 246.748544] drm_kms_helper_hotplug_event+0x2a/0x30 [drm_kms_helper]
[ 246.749439] nv50_mstm_hotplug+0x15/0x20 [nouveau]
[ 246.750111] drm_dp_send_link_address+0x177/0x1c0 [drm_kms_helper]
[ 246.750764] drm_dp_check_and_send_link_address+0xa8/0xd0 [drm_kms_helper]
[ 246.751602] drm_dp_mst_link_probe_work+0x51/0x90 [drm_kms_helper]
[ 246.752314] process_one_work+0x231/0x620
[ 246.752979] worker_thread+0x44/0x3a0
[ 246.753838] kthread+0x12b/0x150
[ 246.754619] ? wq_pool_ids_show+0x140/0x140
[ 246.755386] ? kthread_create_worker_on_cpu+0x70/0x70
[ 246.756162] ret_from_fork+0x3a/0x50
[ 246.756847]
Showing all locks held in the system:
[ 246.758261] 3 locks held by kworker/4:0/37:
[ 246.759016] #0: 00000000f8df4d2d ((wq_completion)"events"){+.+.}, at: process_one_work+0x1b3/0x620
[ 246.759856] #1: 00000000e6065461 ((work_completion)(&(&dev->mode_config.output_poll_work)->work)){+.+.}, at: process_one_work+0x1b3/0x620
[ 246.760670] #2: 00000000cb66735f (&helper->lock){+.+.}, at: drm_fb_helper_hotplug_event.part.28+0x20/0xb0 [drm_kms_helper]
[ 246.761516] 2 locks held by kworker/0:1/60:
[ 246.762274] #0: 00000000fff6be0f ((wq_completion)"pm"){+.+.}, at: process_one_work+0x1b3/0x620
[ 246.762982] #1: 000000005ab44fb4 ((work_completion)(&dev->power.work)){+.+.}, at: process_one_work+0x1b3/0x620
[ 246.763890] 1 lock held by khungtaskd/64:
[ 246.764664] #0: 000000008cb8b5c3 (rcu_read_lock){....}, at: debug_show_all_locks+0x23/0x185
[ 246.765588] 5 locks held by kworker/4:2/422:
[ 246.766440] #0: 00000000232f0959 ((wq_completion)"events_long"){+.+.}, at: process_one_work+0x1b3/0x620
[ 246.767390] #1: 00000000bb59b134 ((work_completion)(&mgr->work)){+.+.}, at: process_one_work+0x1b3/0x620
[ 246.768154] #2: 00000000cb66735f (&helper->lock){+.+.}, at: drm_fb_helper_restore_fbdev_mode_unlocked+0x4c/0xb0 [drm_kms_helper]
[ 246.768966] #3: 000000004c8f0b6b (crtc_ww_class_acquire){+.+.}, at: restore_fbdev_mode_atomic+0x4b/0x240 [drm_kms_helper]
[ 246.769921] #4: 000000004c34a296 (crtc_ww_class_mutex){+.+.}, at: drm_modeset_backoff+0x8a/0x1b0 [drm]
[ 246.770839] 1 lock held by dmesg/1038:
[ 246.771739] 2 locks held by zsh/1172:
[ 246.772650] #0: 00000000836d0438 (&tty->ldisc_sem){++++}, at: ldsem_down_read+0x37/0x40
[ 246.773680] #1: 000000001f4f4d48 (&ldata->atomic_read_lock){+.+.}, at: n_tty_read+0xc1/0x870
[ 246.775522] =============================================
After trying dozens of different solutions, I found one very simple one
that should also have the benefit of preventing us from having to fight
locking for the rest of our lives. So, we work around these deadlocks by
deferring all fbcon hotplug events that happen after the runtime suspend
process starts until after the device is resumed again.
Changes since v7:
- Fixup commit message - Daniel Vetter
Changes since v6:
- Remove unused nouveau_fbcon_hotplugged_in_suspend() - Ilia
Changes since v5:
- Come up with the (hopefully final) solution for solving this dumb
problem, one that is a lot less likely to cause issues with locking in
the future. This should work around all deadlock conditions with fbcon
brought up thus far.
Changes since v4:
- Add nouveau_fbcon_hotplugged_in_suspend() to workaround deadlock
condition that Lukas described
- Just move all of this out of drm_fb_helper. It seems that other DRM
drivers have already figured out other workarounds for this. If other
drivers do end up needing this in the future, we can just move this
back into drm_fb_helper again.
Changes since v3:
- Actually check if fb_helper is NULL in both new helpers
- Actually check drm_fbdev_emulation in both new helpers
- Don't fire off a fb_helper hotplug unconditionally; only do it if
the following conditions are true (as otherwise, calling this in the
wrong spot will cause Bad Things to happen):
- fb_helper hotplug handling was actually inhibited previously
- fb_helper actually has a delayed hotplug pending
- fb_helper is actually bound
- fb_helper is actually initialized
- Add __must_check to drm_fb_helper_suspend_hotplug(). There's no
situation where a driver would actually want to use this without
checking the return value, so enforce that
- Rewrite and clarify the documentation for both helpers.
- Make sure to return true in the drm_fb_helper_suspend_hotplug() stub
that's provided in drm_fb_helper.h when CONFIG_DRM_FBDEV_EMULATION
isn't enabled
- Actually grab the toplevel fb_helper lock in
drm_fb_helper_resume_hotplug(), since it's possible other activity
(such as a hotplug) could be going on at the same time the driver
calls drm_fb_helper_resume_hotplug(). We need this to check whether or
not drm_fb_helper_hotplug_event() needs to be called anyway
Signed-off-by: Lyude Paul <[email protected]>
Reviewed-by: Karol Herbst <[email protected]>
Acked-by: Daniel Vetter <[email protected]>
Cc: [email protected]
Cc: Lukas Wunner <[email protected]>
Signed-off-by: Ben Skeggs <[email protected]>
|
|
Since actual hotplug notifications don't get disabled until
nouveau_display_fini() is called, all this will do is cause any hotplugs
that happen between this drm_kms_helper_poll_disable() call and the
actual hotplug disablement to potentially be dropped if ACPI isn't
around to help us.
Signed-off-by: Lyude Paul <[email protected]>
Acked-by: Karol Herbst <[email protected]>
Acked-by: Daniel Vetter <[email protected]>
Cc: [email protected]
Cc: Lukas Wunner <[email protected]>
Signed-off-by: Ben Skeggs <[email protected]>
|
|
Turns out this part is my fault for not noticing when reviewing
9a2eba337cace ("drm/nouveau: Fix drm poll_helper handling"). Currently
we call drm_kms_helper_poll_enable() from nouveau_display_hpd_work().
This makes basically no sense however, because that means we're calling
drm_kms_helper_poll_enable() every time we schedule the hotplug
detection work. This is also against the advice mentioned in
drm_kms_helper_poll_enable()'s documentation:
Note that calls to enable and disable polling must be strictly ordered,
which is automatically the case when they're only call from
suspend/resume callbacks.
Of course, hotplugs can't really be ordered. They could even happen
immediately after we called drm_kms_helper_poll_disable() in
nouveau_display_fini(), which can lead to all sorts of issues.
Additionally; enabling polling /after/ we call
drm_helper_hpd_irq_event() could also mean that we'd miss a hotplug
event anyway, since drm_helper_hpd_irq_event() wouldn't bother trying to
probe connectors so long as polling is disabled.
So; simply move this back into nouveau_display_init() again. The race
condition that both of these patches attempted to work around has
already been fixed properly in
d61a5c106351 ("drm/nouveau: Fix deadlock on runtime suspend")
Fixes: 9a2eba337cace ("drm/nouveau: Fix drm poll_helper handling")
Signed-off-by: Lyude Paul <[email protected]>
Acked-by: Karol Herbst <[email protected]>
Acked-by: Daniel Vetter <[email protected]>
Cc: Lukas Wunner <[email protected]>
Cc: Peter Ujfalusi <[email protected]>
Cc: [email protected]
Signed-off-by: Ben Skeggs <[email protected]>
|
|
In calculating the global maximum number of the Scatter/Gather elements
supported, the following four maximum parameters must be taken into
consideration: max_sg_rq, max_sg_sq, max_desc_sz_rq and max_desc_sz_sq.
However instead of bringing this complexity to query_device, which still
won't be sufficient anyway (the calculations are dependent on QP type),
the safer approach will be to restore old code, which will give us 32
SGEs.
Fixes: 33023fb85a42 ("IB/core: add max_send_sge and max_recv_sge attributes")
Reported-by: Chuck Lever <[email protected]>
Signed-off-by: Leon Romanovsky <[email protected]>
Signed-off-by: Jason Gunthorpe <[email protected]>
|
|
When AF_IB addresses are used during rdma_resolve_addr() a lock is not
held. A cma device can get removed while list traversal is in progress
which may lead to crash. ie
CPU0 CPU1
==== ====
rdma_resolve_addr()
cma_resolve_ib_dev()
list_for_each() cma_remove_one()
cur_dev->device mutex_lock(&lock)
list_del();
mutex_unlock(&lock);
cma_process_remove();
Therefore, hold a lock while traversing the list which avoids such
situation.
Cc: <[email protected]> # 3.10
Fixes: f17df3b0dede ("RDMA/cma: Add support for AF_IB to rdma_resolve_addr()")
Signed-off-by: Parav Pandit <[email protected]>
Reviewed-by: Daniel Jurgens <[email protected]>
Signed-off-by: Leon Romanovsky <[email protected]>
Reviewed-by: Dennis Dalessandro <[email protected]>
Signed-off-by: Jason Gunthorpe <[email protected]>
|
|
Disable interrupts while configuring the transfer and enable them back.
We have below as the programming sequence
1. start and slave address
2. byte count and stop
In some customer platform there was a lot of interrupts between 1 and 2
and after slave address (around 7 clock cyles) if 2 is not executed
then the transaction is nacked.
To fix this case make the 2 writes atomic.
Signed-off-by: Shubhrajyoti Datta <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
[wsa: added a newline for better readability]
Signed-off-by: Wolfram Sang <[email protected]>
Cc: [email protected]
|
|
Commit fe8e93504ce8 ("irqchip/gic-v3-its: Use full range of LPIs"), removes
the cap for lpi_id_bits, which causes the following warning to trigger on a
QDF2400 server:
WARNING: CPU: 0 PID: 0 at mm/page_alloc.c:4066 __alloc_pages_nodemask
...
Call trace:
__alloc_pages_nodemask+0x2d8/0x1188
alloc_pages_current+0x8c/0xd8
its_allocate_prop_table+0x5c/0xb8
its_init+0x220/0x3c0
gic_init_bases+0x250/0x380
gic_acpi_init+0x16c/0x2a4
In its_alloc_lpi_tables(), lpi_id_bits is 24 in QDF2400. The allocation in
allocate_prop_table() tries therefore to allocate 16M (order 12 if
pagesize=4k), which triggers the warning.
As said by MarcL
Capping lpi_id_bits at 16 (which is what we had before) is plenty,
will save a some memory, and gives some margin before we need to push
it up again.
Bring the upper limit of lpi_id_bits back to prevent
Fixes: fe8e93504ce8 ("irqchip/gic-v3-its: Use full range of LPIs")
Suggested-by: Marc Zyngier <[email protected]>
Signed-off-by: Jia He <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
Acked-by: Marc Zyngier <[email protected]>
Tested-by: Olof Johansson <[email protected]>
Cc: Jason Cooper <[email protected]>
Cc: [email protected]
Link: https://lkml.kernel.org/r/[email protected]
|
|
Loading a new mapping table, the dm-raid target's constructor
retrieves the volatile reshaping state from the raid superblocks.
When the new table is activated in a following resume, the actual
reshape position is retrieved. The reshape driven by the previous
mapping can already have finished on small and/or fast devices thus
updating raid superblocks about the new raid layout.
This causes the actual array state (e.g. stripe size reshape finished)
to be inconsistent with the one in the new mapping, causing hangs with
left behind devices.
This race does not occur with usual raid device sizes but with small
ones (e.g. those created by the lvm2 test suite).
Fix by no longer transferring stale/inconsistent raid_set state during
preresume.
Signed-off-by: Heinz Mauelshagen <[email protected]>
Signed-off-by: Mike Snitzer <[email protected]>
|
|
There's a XFS on dm-crypt deadlock, recursing back to itself due to the
crypto subsystems use of GFP_KERNEL, reported here:
https://bugzilla.kernel.org/show_bug.cgi?id=200835
* dm-crypt calls crypt_convert in xts mode
* init_crypt from xts.c calls kmalloc(GFP_KERNEL)
* kmalloc(GFP_KERNEL) recurses into the XFS filesystem, the filesystem
tries to submit some bios and wait for them, causing a deadlock
Fix this by updating both the DM crypt and integrity targets to no
longer use the CRYPTO_TFM_REQ_MAY_SLEEP flag, which will change the
crypto allocations from GFP_KERNEL to GFP_ATOMIC, therefore they can't
recurse into a filesystem. A GFP_ATOMIC allocation can fail, but
init_crypt() in xts.c handles the allocation failure gracefully - it
will fall back to preallocated buffer if the allocation fails.
The crypto API maintainer says that the crypto API only needs to
allocate memory when dealing with unaligned buffers and therefore
turning CRYPTO_TFM_REQ_MAY_SLEEP off is safe (see this discussion:
https://www.redhat.com/archives/dm-devel/2018-August/msg00195.html )
Cc: [email protected]
Signed-off-by: Mikulas Patocka <[email protected]>
Signed-off-by: Mike Snitzer <[email protected]>
|
|
Platform data pointer may be NULL. We check it everywhere but in one
place. Fix it.
Fixes: 8af70cd2ca50 ("memory: aemif: add support for board files")
Reported-by: Dan Carpenter <[email protected]>
Signed-off-by: Bartosz Golaszewski <[email protected]>
Cc: [email protected]
Signed-off-by: Olof Johansson <[email protected]>
|
|
https://github.com/Broadcom/stblinux into fixes
This pull request contains Broadcom ARM/ARM64 SoCs drivers fixes for
4.19, please pull the following:
- Peter adds an alias to the Raspberry Pi HWMON driver that was just
merged as part of the 4.19 merge window
* tag 'arm-soc/for-4.19/drivers-fixes' of https://github.com/Broadcom/stblinux:
hwmon: rpi: add module alias to raspberrypi-hwmon
Signed-off-by: Olof Johansson <[email protected]>
|
|
Firmware can provide zero as values for sustained performance level and
corresponding sustained frequency in kHz in order to hide the actual
frequencies and provide only abstract values. It may endup with divide
by zero scenario resulting in kernel panic.
Let's set the multiplication factor to one if either one or both of them
(sustained_perf_level and sustained_freq) are set to zero.
Fixes: a9e3fbfaa0ff ("firmware: arm_scmi: add initial support for performance protocol")
Reported-by: Ionela Voinescu <[email protected]>
Signed-off-by: Sudeep Holla <[email protected]>
Signed-off-by: Olof Johansson <[email protected]>
|
|
Raydium touchscreen triggers interrupt storm after system-wide suspend:
[ 179.085033] i2c_hid i2c-CUST0000:00: i2c_hid_get_input: incomplete report (58/65535)
According to Raydium, Windows driver does not reset the device after system
resume.
The HID over I2C spec does specify a reset should be used at intialization, but
it doesn't specify if reset is required for system suspend.
Tested this patch on other i2c-hid touchpanels I have and those touchpanels do
work after S3 without doing reset. If any regression happens to other
touchpanel vendors, we can use quirk for Raydium devices.
There's still one device uses I2C_HID_QUIRK_RESEND_REPORT_DESCR so keep it
there.
Cc: Aaron Ma <[email protected]>
Cc: AceLan Kao <[email protected]>
Signed-off-by: Kai-Heng Feng <[email protected]>
Reviewed-by: Benjamin Tissoires <[email protected]>
Signed-off-by: Jiri Kosina <[email protected]>
|
|
If parent_get class method is not supported by the OSDs, fall back to
the legacy class method and assume that the parent is in the default
(i.e. "") namespace. The "use the child's image namespace" workaround
is no longer needed because creating images within namespaces will
require parent_get aware OSDs.
Signed-off-by: Ilya Dryomov <[email protected]>
Reviewed-by: Jason Dillaman <[email protected]>
|
|
In preparation for the new parent_get and parent_overlap_get class
methods, factor out the fetching and decoding of parent data.
As a side effect, we now decode all four fields in the "no parent"
case.
Signed-off-by: Ilya Dryomov <[email protected]>
Reviewed-by: Jason Dillaman <[email protected]>
|
|
Commit 12864ff8545f (ACPI / LPSS: Avoid PM quirks on suspend and resume
from hibernation) bypasses lpss quirks for S3 and S4, by setting a flag
for S3/S4 in acpi_lpss_suspend(), and check that flag in
acpi_lpss_resume().
But this overlooks the boot case where acpi_lpss_resume() may get called
without a corresponding acpi_lpss_suspend() having been called.
Thus force setting the flag during boot.
Fixes: 12864ff8545f (ACPI / LPSS: Avoid PM quirks on suspend and resume from hibernation)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=200989
Reported-and-tested-by: William Lieurance <[email protected]>
Signed-off-by: Zhang Rui <[email protected]>
Cc: 4.15+ <[email protected]> # 4.15+: 12864ff8545f (ACPI / LPSS: Avoid ...)
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
Calling dmi_check_system() early only works on X86. Other
architectures initialize the DMI subsystem later so it's not
ready yet when ACPI itself gets initialized.
In the best case it results in a useless call to a function which
will do nothing. But depending on the dmi implementation, it could
also result in warnings. Best is to not call the function when it
can't work and isn't needed.
Additionally, if anyone ever needs to add non-x86 quirks, it would
surprisingly not work, so document the limitation to avoid confusion.
Signed-off-by: Jean Delvare <[email protected]>
Fixes: cce4f632db20 (ACPI: fix early DSDT dmi check warnings on ia64)
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.19-rc2
NET2280 got a fix to an old patch attempting to fix locking for gadget
framework callbacks.
DWC2 fixed a bug where driver was attempting to access registers before
clocks were enabled.
DWC3 got a fix for ULPI clock configuration on Baytrail devices.
FOTG210 plugged a memory leak and Renesas USB3 fixed ep0 maxpacket size.
|
|
GVT-g emualte the opregion for guest with bdb version as '186' which
child_device_config length should be '33'.
v2: split into 2 patch. 1st for issue fix, 2nd for code clean up.(Zhenyu)
v3: add fixes tag.(Zhenyu)
Fixes: 4023f301d28f ("drm/i915/gvt: opregion virtualization for win")
CC: Xiaolin Zhang <[email protected]>
Reviewed-by: Xiaolin Zhang <[email protected]>
Signed-off-by: Weinan Li <[email protected]>
Signed-off-by: Zhenyu Wang <[email protected]>
|
|
This is a false positive report due to incorrect nested lock
annotations as we lock multiple fgs with the same subclass.
Instead of locking all fgs only lock the one being used as was
done before.
Fixes: bd71b08ec2ee ("net/mlx5: Support multiple updates of steering rules in parallel")
Signed-off-by: Roi Dayan <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
|
|
Copy and paste bug was introduced in the offending patch.
We need to write udp source port value into the headers value and not
headers criteria "mask".
Fixes: 142644f8a1f8 ("net/mlx5e: Ethtool steering flow parsing refactoring")
Signed-off-by: Saeed Mahameed <[email protected]>
|
|
Currently, mlx5_attach_interface does not check for error
after calling intf->attach or intf->add. When these two calls
fails, the client is not initialized and will cause issues such as
kernel panic on invalid address in the teardown path (mlx5_detach_interface)
Fixes: 737a234bb638 ("net/mlx5: Introduce attach/detach to interface API")
Signed-off-by: Huy Nguyen <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
|