| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
When the bound device of a tunnel device is down, encapsulated packets
are not egressed anymore, but tunnel decap still works. Extend
mlxsw_sp_nexthop_rif_update() to take IFF_UP into consideration when
deciding whether a given next hop should be offloaded.
Because the new logic was added to mlxsw_sp_nexthop_rif_update(), this
fixes the case where a newly-added tunnel has a down bound device, which
would previously be fully offloaded. Now the down state of the bound
device is noted and next hops forwarding to such tunnel are not
offloaded.
In addition to that, notice NETDEV_UP and NETDEV_DOWN of a bound device
to force refresh of tunnel encap route offloads.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a bound device of an IP-in-IP tunnel changes, such as through
'ip tunnel change name $name dev $dev', the loopback backing the tunnel
needs to be recreated.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Changes to L3 tunnel netdevices (through `ip tunnel change' as well as
`ip link set') lead to NETDEV_CHANGE being generated on the tunnel
device. Because what is relevant for the tunnel in question depends on
the tunnel type, handling of the event is dispatched to the IPIP module
through a newly-added interface mlxsw_sp_ipip_ops.ol_netdev_change().
IPIP tunnels now remember the last set of tunnel parameters in struct
mlxsw_sp_ipip_entry.parms, and use it to figure out what exactly has
changed.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a bound device of a tunnel netdevice changes VRF, the loopback RIF
that backs the tunnel needs to be updated and existing encapsulating
routes need to be refreshed.
Note that several tunnels can share the same bound device, in which case
all the impacted tunnels need to be updated.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The approach for offloading IP tunnels implemented currently by mlxsw
doesn't allow two tunnels that have the same local IP address in the
same (underlay) VRF. Previously, offloads were introduced on demand as
encap routes were formed. When such a route was created that would cause
offload of a conflicting tunnel, mlxsw_sp_ipip_entry_create() would
detect it and return -EEXIST, which would propagate up and cause FIB
abort.
Now however IPIP entries are created as soon as an offloadable netdevice
is created, and the failure prevents creation of such device.
Furthermore, if the driver is installed at the point where such
conflicting tunnels exist, the failure actually prevents successful
modprobe.
Furthermore, follow-up patches implement handling of NETDEV_CHANGE due
to the local address change. However, NETDEV_CHANGE can't be vetoed. The
failure merely means that the offloads weren't updated, but the change
in Linux configuration is not rolled back. It is thus desirable to have
a robust way of handling these conflicts, which can later be reused for
handling NETDEV_CHANGE as well.
To fix this, when a conflicting tunnel is created, instead of failing,
simply pull the old tunnel to slow path and reject offloading the
new one.
Introduce two functions: mlxsw_sp_ipip_entry_demote_tunnel() and
mlxsw_sp_ipip_demote_tunnel_by_saddr() to handle this. Make them both
public, because they will be useful later on in this patchset.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When trying to determine whether there are other offloaded tunnels with
the same local address, mlxsw_sp_ipip_entry_create() should look for a
tunnel with matching UL protocol, matching saddr, in the same VRF.
However instead of taking into account the UL protocol of the tunnel
netdevice (which mlxsw_sp_ipip_entry_saddr_matches() then compares to
the UL protocol of inspected IPIP entry), it deduces the UL protocol
from the inspected IPIP entry (and that's compared to itself).
This is currently immaterial, because only one tunnel type is offloaded,
and therefore the UL protocol always matches, but introducing support
for a tunnel with IPv6 underlay would uncover this error.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The work that needs to be done to update HW configuration in response to
changes is similar to what __mlxsw_sp_ipip_entry_update_tunnel() already
does, but with a number of twists: each change requires a different
subset of things to happen. Extend the function to support all these
uses, and allow finely-grained configuration of what should happen at
each call through a suite of function arguments.
Publish the updated function to allow use from the spectrum_ipip module.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The work that's done by mlxsw_sp_netdevice_ipip_ol_vrf_event() is a good
basis for a more versatile function that would take care of all sorts of
tunnel updates requests: __mlxsw_sp_ipip_entry_update_tunnel(). Extract
that function. Factor out a helper mlxsw_sp_ipip_entry_ol_lb_update() as
well.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The function mlxsw_sp_rif_create() takes an extack parameter. So far,
for creation of loopback interfaces, NULL was passed. For some events
however the extack can be extracted and passed along. So do that for
NETDEV_CHANGEUPPER handler.
Use the opportunity to update the type of info argument that
mlxsw_sp_netdevice_ipip_ol_event() takes. Follow-up patches will
introduce handling of more changes, and some of them carry an extack as
well, but in an info structure of a different type. Though not strictly
erroneous (the pointer could be cast whichever way), it makes no sense
to pretend the value is always of a certain type, when in fact it isn't.
So change the prototype of the above-mentioned function as well.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The piece of logic to promote decap route, if any, is useful for generic
tunnel updates, not just for handling of NETDEV_UP events on tunnel
interfaces. Extract it to a separate function.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This function only ever returns 0, so don't pretend it returns anything
useful and just make it void.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To implement NETDEV_CHANGE notifications on IP-in-IP tunnels, the
handler needs to figure out what actually changed, to understand how
exactly to update the offloads. It will do so by storing struct
ip_tunnel_parm with previous configuration, and comparing that to the
new version.
To facilitate these comparisons, extract the code that operates on
struct ip_tunnel_parm from the existing accessor functions, and make
those a thin wrapper that extracts tunnel parameters and dispatches.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These functions ideologically belong to the IPIP module, and some
follow-up work will benefit from their presence there.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some of the code down the road needs this logic as well.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To distinguish between events related to tunnel device itself and its
bound device, rename a number of functions related to handling tunneling
netdevice events to include _ol_ (for "overlay") in the name. That
leaves room in the namespace for underlay-related functions, which would
have _ul_ in the name.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fix from Stephen Boyd:
"One fix for USB clks on Uniphier PXs3 SoCs"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: uniphier: fix clock data for PXs3
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fix from James Bottomley:
"One minor fix in the error leg of the qla2xxx driver (it oopses the
system if we get an error trying to start the internal kernel thread).
The fix is minor because the problem isn't often encountered in the
field (although it can be induced by inserting the module in a low
memory environment)"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: qla2xxx: Fix oops in qla2x00_probe_one error path
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"Fix dw_mmc request timeout issues"
* tag 'mmc-v4.14-rc4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: dw_mmc: Fix the DTO timeout calculation
mmc: dw_mmc: Add locking to the CTO timer
mmc: dw_mmc: Fix the CTO timeout calculation
mmc: dw_mmc: cancel the CTO timer after a voltage switch
|
|
git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
- one nouveau regression fix
- some amdgpu fixes for stable to fix hangs on some harvested Polaris
GPUs
- a set of KASAN and regression fixes for i915, their CI system seems
to be working pretty well now.
* tag 'drm-fixes-for-v4.14-rc8' of git://people.freedesktop.org/~airlied/linux:
drm/amdgpu: allow harvesting check for Polaris VCE
drm/amdgpu: return -ENOENT from uvd 6.0 early init for harvesting
drm/i915: Check incoming alignment for unfenced buffers (on i915gm)
drm/nouveau/kms/nv50: use the correct state for base channel notifier setup
drm/i915: Hold rcu_read_lock when iterating over the radixtree (vma idr)
drm/i915: Hold rcu_read_lock when iterating over the radixtree (objects)
drm/i915/edp: read edp display control registers unconditionally
drm/i915: Do not rely on wm preservation for ILK watermarks
drm/i915: Cancel the modeset retry work during modeset cleanup
|
|
Pull networking fixes from David Miller:
"Hopefully this is the last batch of networking fixes for 4.14
Fingers crossed...
1) Fix stmmac to use the proper sized OF property read, from Bhadram
Varka.
2) Fix use after free in net scheduler tc action code, from Cong
Wang.
3) Fix SKB control block mangling in tcp_make_synack().
4) Use proper locking in fib_dump_info(), from Florian Westphal.
5) Fix IPG encodings in systemport driver, from Florian Fainelli.
6) Fix division by zero in NV TCP congestion control module, from
Konstantin Khlebnikov.
7) Fix use after free in nf_reject_ipv4, from Tejaswi Tanikella"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net: systemport: Correct IPG length settings
tcp: do not mangle skb->cb[] in tcp_make_synack()
fib: fib_dump_info can no longer use __in_dev_get_rtnl
stmmac: use of_property_read_u32 instead of read_u8
net_sched: hold netns refcnt for each action
net_sched: acquire RTNL in tc_action_net_exit()
net: vrf: correct FRA_L3MDEV encode type
tcp_nv: fix division by zero in tcpnv_acked()
netfilter: nf_reject_ipv4: Fix use-after-free in send_reset
netfilter: nft_set_hash: disable fast_ops for 2-len keys
|
|
MIPS will soon not be a part of Imagination Technologies, and as such
many @imgtec.com email addresses will no longer be valid. This patch
updates the addresses for those who:
- Have 10 or more patches in mainline authored using an @imgtec.com
email address, or any patches dated within the past year.
- Are still with Imagination but leaving as part of the MIPS business
unit, as determined from an internal email address list.
- Haven't already updated their email address (ie. JamesH) or expressed
a desire to be excluded (ie. Maciej).
- Acked v2 or earlier of this patch, which leaves Deng-Cheng, Matt &
myself.
New addresses are of the form firstname.lastname@mips.com, and all
verified against an internal email address list. An entry is added to
.mailmap for each person such that get_maintainer.pl will report the new
addresses rather than @imgtec.com addresses which will soon be dead.
Instances of the affected addresses throughout the tree are then
mechanically replaced with the new @mips.com address.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Cc: Deng-Cheng Zhu <dengcheng.zhu@mips.com>
Acked-by: Dengcheng Zhu <dengcheng.zhu@mips.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Matt Redfearn <matt.redfearn@mips.com>
Acked-by: Matt Redfearn <matt.redfearn@mips.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: trivial@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch fixes a bug for phy supported feature initialization.
Currently, the value of phydev->supported is initialized by kernel.
So it includes many features that we do not support, such as
SUPPORTED_FIBRE and SUPPORTED_BNC. This patch fixes it.
Fixes: 256727d (net: hns3: Add MDIO support to HNS3 Ethernet driver for hip08 SoC)
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds nway_reset support for ethtool cmd.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds set_link_ksettings support for ethtool cmd.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The value of link_modes.advertising and the value of link_modes.supported
is initialized to zero every time in for loop in hns3_driv_to_eth_caps().
But we just want to set specified bit for them. Initialization is
unnecessary. This patch fixes it.
Fixes: 496d03e (net: hns3: Add Ethtool support to HNS3 driver)
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes a bug for ethtool's get_link_ksettings().
The advertising for autoneg is always added to advertised_caps
whether autoneg is enable or disable. This patch fixes it.
Fixes: 496d03e (net: hns3: Add Ethtool support to HNS3 driver)
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes a bug for ethtool's get_link_ksettings().
When phy exists, we should get autoneg from phy rather than from mac.
Because the value of mac.autoneg is invalid when phy exists.
Fixes: 496d03e (net: hns3: Add Ethtool support to HNS3 driver)
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Recent IRQ coalescing clean up has removed a guard-rail for the max DMA
buffer coalescing value. This is a 6-bit value and must not be 0. We
already have a check for 0 but 64 is equivalent to 0 and will cause
non-stop interrupts. Fix it by adding the proper check.
Fixes: f8503969d27b ("bnxt_en: Refactor and simplify coalescing code.")
Reported-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Recent refactoring of coalesce settings contained a typo that prevents
receive settings from being set properly.
Fixes: 18775aa8a91f ("bnxt_en: Reorganize the coalescing parameters.")
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
add four new PCI ID'S for a000 series
Signed-off-by: Ihab Zhaika <ihab.zhaika@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
add two new PCI ID'S for 8265 series
Signed-off-by: Ihab Zhaika <ihab.zhaika@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
add three new PCI ID'S for 8260 series
Signed-off-by: Ihab Zhaika <ihab.zhaika@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
In case of a hardware restart the BA session data in HW is lost
so the reorder buffer simply passes the frames to mac80211 as is
as there is no NSSN set. Instead, we will drop these frames
before they reach the reorder buffer. mac80211 drops such frames anyway,
but we shouldn't rely on that. In addition it saves some
processing time
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
The RCU lifetime on baid_data is unclear, so this adds a direct copy of the
rcu_ptr passed to the original callback. It may be possible to improve this
to just use baid_data->mvm->baid_map[baid_data->baid] instead.
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Sara Sharon <sara.sharon@intel.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The iwl_mvm_flush_tx_path() function sends a synchronous command to
the firmware. When doing that, we must hold the mutex. The
iwl_mvm_flush_no_vif() function was mistakenly not holding the mutex.
Fix it.
Fixes: 6110d9e5bdd1 ("iwlwifi: mvm: Flush non STA TX queues")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
In the mac flush flow, we should flush all existing queues.
Since FW API for a000 devices is flush per RA-TID, simply
flush all stations with all tids.
From FW perspective, asking to flush a TID that doesn't have
a queue is valid, so we can just set all bits in the TID mask.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
This function is very indented and hard to read.
Refactor it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Currently we return early from sync_rx_queues for a000 devices.
This may cause, in case of a non-empty reorder buffer, a warning
later on since the RX queue isn't getting the notification to
empty it.
A better approach would be to send the notification for the default
queue only.
Do this hard coded for now, until we will have the API to enable
multi queue for a000 devices.
Fixes: bc0294696456 ("iwlwifi: mvm: disable RX queue notification for a000 devices")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Commit a6d24fad00d9 ("iwlwifi: pcie: dump registers when HW becomes
inaccessible") added a function to dump pcie config registers and
memory mapped registers on a failure. It is currently only accessible
within trans.c. Add it to struct iwl_trans_ops, so that failure cases
in other files can call it. While there, add a call to this function
from iwl_pcie_load_firmware_chunk in pcie/tx.c, since this is a common
failure case seen on some platforms.
Signed-off-by: Kirtika Ruchandani <kirtika@chromium.org>
[modified the commit message slightly]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
This was used for internal devices that are now deprecated.
All the currently existing devices can do paging without
any help from the host.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
We had a bunch of code that was relevant for internal
devices only. Those devices are now being depreceated.
Kill all the now unneeded code.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
When there is a reorder timeout, we may get to a situation
where we have the timeout latency for all the next 64 frames.
This happens since NSSN is behind for a while, and the driver
won't release the frames, since it is not allowed by NSSN.
As a result the frame is stored in the reorder buffer although
there is no hole, and released 100 ms later.
Add a direct comparison to the reorder buffer head, and release
immediately if possible.
For example:
Frame 0 is missed. We receive frame 1, and store it in the buffer.
After 100 ms, frame 1 is released and reorder buffer head is 2.
We then receive frame 2, with NSSN 0, and store it instead of
releasing it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
We don't plan to have products with 3 antennas in the near
future. All the rest of the code follows the same
assumption as well.
Remove the support for antenna C from rs_toggle_ant.
When trying to toggle from ANT_B, this avoids to go through
ANT_C, discover that it doesn't exist and continue to ANT_A.
In MIMO, this avoids to do ANT_AB -> ANT_BC -> ANT_AC and
back to ANT_AB.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
After a FW reset on A000 NICs, the driver doesn't
set the seq number when re-allocating the queues.
This in turn leads to a mismatch between the seq
number the driver thinks each frame has, and the
actual seq num given by the HW.
This especially causes issues with aggregations,
since the driver could be waiting to start an
aggregation and queue traffic from the mac80211
until then, when actually it shouldn't be waiting.
Fixes: 310181ec34e2 ("iwlwifi: move to TVQM mode")
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Currently the code is mixing defines and is inconsistent.
When enabling a queue, we usually configure the scheduler
with IWL_FRAME_LIMIT - 64.
When sending to firmware the rate scaling, we limit aggregation
to LINK_QUAL_AGG_FRAME_LIMIT_DEF - 63, due to a scheduler bug.
Given that, clean up the following:
- Fix a stray queue enablement with LINK_QUAL_AGG_FRAME_LIMIT_DEF.
- Change the comparison that tests if queue needs to be reconfigured
to be compared directly to how it was configured.
This also saves the redundant round down of the buffer size just
for the sake of comparing it, making the code more readable.
- Better document gen2 logic
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
There is a macro for converting TX response rate to a
rate scale value, use it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Arvind Yadav <arvind.yadav.cs@gmail.com>
Cc: Geliang Tang <geliangtang@gmail.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114780
Addresses-Coverity-ID: 114781
Addresses-Coverity-ID: 114782
Addresses-Coverity-ID: 114783
Addresses-Coverity-ID: 114784
Addresses-Coverity-ID: 114785
Addresses-Coverity-ID: 114786
Addresses-Coverity-ID: 114787
Addresses-Coverity-ID: 114788
Addresses-Coverity-ID: 114789
Addresses-Coverity-ID: 114790
Addresses-Coverity-ID: 114791
Addresses-Coverity-ID: 114792
Addresses-Coverity-ID: 114793
Addresses-Coverity-ID: 114794
Addresses-Coverity-ID: 114795
Addresses-Coverity-ID: 200521
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support to new ethtool operation get_fecparam to
fetch FEC parameters.
Original Work by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|