| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://anongit.freedesktop.org/drm-intel into drm-fixes
three commits, all cc: stable, to address Baytrail
suspend/resume issues.
* tag 'drm-intel-fixes-2015-04-08' of git://anongit.freedesktop.org/drm-intel:
drm/i915/vlv: remove wait for previous GFX clk disable request
drm/i915/chv: Remove Wait for a previous gfx force-off
drm/i915/vlv: save/restore the power context base reg
|
|
When the CONTINUE bit is set, the interrupt status we are polling to
identify if a transaction has finished can be sporadic. Even though
the transfer has finished, the interrupt status may erroneously
indicate that there is still data in the FIFO. This behaviour causes
random timeouts in large PIO transfers.
Instead of using the CONTINUE bit to control the CS lines, use the SPI
core's CS GPIO handling. Also, now that the CONTINUE bit is not being
used, we can poll for the ALLDONE interrupt to indicate transfer
completion.
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi into spi-img-spfi
|
|
Imagination has recommended that the SPFI controller be reset after
each message, regardless of success or failure. Do this in an
unprepare_message() callback.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The driver can be greatly simplified by moving the transfer timeout
handling to a handle_err() callback.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Linux 4.0-rc7
|
|
The find_pci_host_bridge() function can be useful to other PCI code so
export it. Change its name to pci_find_host_bridge().
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The PCI Firmware Specification, r3.0, sec 4.6.4.1.3, defines a single UUID
for an ACPI _DSM method to provide device-specific control functions. This
_DSM method support several functions, including PCI Express Slot
Information, PCI Express Slot Number, PCI Bus Capabilities, etc.
Move the UUID definition from pci/pci-label.c, where it could be used only
for one function, to pci/pci-acpi.c where it can be shared for all these
functions.
[bhelgaas: changelog]
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Fix a typo in one of the kernel messages.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Use a semicolon, not a comma, to terminate a statement.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Add support for the Broadcom iProc PCIe controller.
pcie-iproc.c is the common core driver, and a front-end bus interface needs
to be added to support different bus interfaces.
pcie-iproc-platform.c contains the support for the platform bus interface.
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
|
|
Export the following symbols so they can be referenced by a PCI host bridge
driver compiled as a kernel loadable module:
pci_common_swizzle
pci_create_root_bus
pci_stop_root_bus
pci_remove_root_bus
pci_assign_unassigned_bus_resources
pci_fixup_irqs
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
|
|
The new OPAL device tree adds a few properties which can be used to add
extra information on the sensor label.
In the case of a cpu core sensor, the firmware exposes the physical
identifier of the core in the "ibm,pir" property. The driver
translates this identifier in a linux cpu number and prints out a
range corresponding to the hardware threads of the core (as they
share the same sensor).
The numbering gives a hint on the localization of the core in the
system (which socket, which chip).
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Currently, sensors are only identified by their type and index.
The new OPAL device tree can expose extra properties to identify
some sensors by their name or location. This patch adds the creation
of a new hwmon *_label attribute when such properties are detected.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The new OPAL device tree for sensors has a different layout and uses new
property names, for the type and for the handler used to capture the
sensor data.
This patch modifies the ibmpowernv driver to support such a tree in a
way preserving compatibility with older OPAL firmwares.
This is achieved by changing the error path of the routine parsing
an OPAL node name. The node is simply considered being from the new
device tree layout and fallback values are used.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This should shorten a bit the code necessary to create a hmwon attribute.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
SCSI transport drivers and SCSI LLDs block a SCSI device if the
transport layer is not operational. This means that in this state
no requests should be processed, even if the REQ_PREEMPT flag has
been set. This patch avoids that a rescan shortly after a cable
pull sporadically triggers the following kernel oops:
BUG: unable to handle kernel paging request at ffffc9001a6bc084
IP: [<ffffffffa04e08f2>] mlx4_ib_post_send+0xd2/0xb30 [mlx4_ib]
Process rescan-scsi-bus (pid: 9241, threadinfo ffff88053484a000, task ffff880534aae100)
Call Trace:
[<ffffffffa0718135>] srp_post_send+0x65/0x70 [ib_srp]
[<ffffffffa071b9df>] srp_queuecommand+0x1cf/0x3e0 [ib_srp]
[<ffffffffa0001ff1>] scsi_dispatch_cmd+0x101/0x280 [scsi_mod]
[<ffffffffa0009ad1>] scsi_request_fn+0x411/0x4d0 [scsi_mod]
[<ffffffff81223b37>] __blk_run_queue+0x27/0x30
[<ffffffff8122a8d2>] blk_execute_rq_nowait+0x82/0x110
[<ffffffff8122a9c2>] blk_execute_rq+0x62/0xf0
[<ffffffffa000b0e8>] scsi_execute+0xe8/0x190 [scsi_mod]
[<ffffffffa000b2f3>] scsi_execute_req+0xa3/0x130 [scsi_mod]
[<ffffffffa000c1aa>] scsi_probe_lun+0x17a/0x450 [scsi_mod]
[<ffffffffa000ce86>] scsi_probe_and_add_lun+0x156/0x480 [scsi_mod]
[<ffffffffa000dc2f>] __scsi_scan_target+0xdf/0x1f0 [scsi_mod]
[<ffffffffa000dfa3>] scsi_scan_host_selected+0x183/0x1c0 [scsi_mod]
[<ffffffffa000edfb>] scsi_scan+0xdb/0xe0 [scsi_mod]
[<ffffffffa000ee13>] store_scan+0x13/0x20 [scsi_mod]
[<ffffffff811c8d9b>] sysfs_write_file+0xcb/0x160
[<ffffffff811589de>] vfs_write+0xce/0x140
[<ffffffff81158b53>] sys_write+0x53/0xa0
[<ffffffff81464592>] system_call_fastpath+0x16/0x1b
[<00007f611c9d9300>] 0x7f611c9d92ff
Reported-by: Max Gurtuvoy <maxg@mellanox.com>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: <stable@vger.kernel.org>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Kernel panic was happening as iscsi_host_remove() was called on
a host which was not yet added.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: <stable@vger.kernel.org>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Booting a v3.18 or newer Xen domU kernel with PCI devices passed through
results in an oops (this is a 32-bit 3.13.11 dom0 with a 64-bit 4.4.0
hypervisor and 32-bit domU):
BUG: unable to handle kernel paging request at 0030303e
IP: [<c06ed0e6>] acpi_ns_validate_handle+0x12/0x1a
Call Trace:
[<c06eda4d>] ? acpi_evaluate_object+0x31/0x1fc
[<c06b78e1>] ? pci_get_hp_params+0x111/0x4e0
[<c0407bc7>] ? xen_force_evtchn_callback+0x17/0x30
[<c04085fb>] ? xen_restore_fl_direct_reloc+0x4/0x4
[<c0699d34>] ? pci_device_add+0x24/0x450
Don't look for ACPI configuration information if ACPI has been disabled.
I don't think this is the best fix, because we can boot plain Linux (no
Xen) with "acpi=off", and we don't need this check in pci_get_hp_params().
There should be a better fix that would make Xen domU work the same way.
The domU kernel has ACPI support but it has no AML. There should be a way
to initialize the ACPI data structures so things fail gracefully rather
than oopsing. This is an interim fix to address the regression.
Fixes: 6cd33649fa83 ("PCI: Add pci_configure_device() during enumeration")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=96301
Reported-by: Michael D Labriola <mlabriol@gdeb.com>
Tested-by: Michael D Labriola <mlabriol@gdeb.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.18+
|
|
Replace occurences of the pci api by appropriate call to the dma api.
A simplified version of the semantic patch that finds this problem is as
follows: (http://coccinelle.lip6.fr)
@deprecated@
idexpression id;
position p;
@@
(
pci_dma_supported@p ( id, ...)
|
pci_alloc_consistent@p ( id, ...)
)
@bad1@
idexpression id;
position deprecated.p;
@@
...when != &id->dev
when != pci_get_drvdata ( id )
when != pci_enable_device ( id )
(
pci_dma_supported@p ( id, ...)
|
pci_alloc_consistent@p ( id, ...)
)
@depends on !bad1@
idexpression id;
expression direction;
position deprecated.p;
@@
(
- pci_dma_supported@p ( id,
+ dma_supported ( &id->dev,
...
+ , GFP_ATOMIC
)
|
- pci_alloc_consistent@p ( id,
+ dma_alloc_coherent ( &id->dev,
...
+ , GFP_ATOMIC
)
)
Signed-off-by: Quentin Lambert <lambert.quentin@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Tidy up error reporting and move rpm reference retrieval out of the for
loop for improved readability.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Modeling the individual RPM resources as platform devices consumes at
least 12-15kb of RAM, just to hold the platform_device structs. Rework
this to instead have one device per pmic exposed by the RPM.
With this representation we can more accurately define the input pins on
the pmic and have the supply description match the data sheet.
Suggested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Refactor out all custom property parsing code from the probe function
into a function suitable for regulator_desc->of_parse_cb usage.
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The driver itself should not flag regulators as being DRMS compatible,
this should come from board or dt files.
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
pdata is assigned to &pdata_of, however, pdata_of becomes dead (when it
goes out of scope) so pdata effectively becomes a dead pointer to the
out of scope object. This is detected by static analysis:
[drivers/regulator/max8660.c:411]: (error) Dead pointer usage.
Pointer 'pdata' is dead if it has been assigned '&pdata_of' at line 404.
Move declaration of pdata_of so it is always in scope.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Setting the transfer length in the TRANSACTION register after the
CONTROL register is programmed causes intermittent timeout issues in
SPFI transfers when using the SPI framework to control the CS GPIO
lines. To avoid this issue, set transfer length before programming
the CONTROL register.
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Also check MMC OF properties. The controller supports MMC too.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
rts5250 chip failed handle 64 bit ADMA for address below 4G.
Add 64 BIT quirks to disable this feature.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Conflicts:
arch/x86/kernel/entry_64.S
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Since the required clock to access registers is gated off in low power mode,
add ci->in_lpm check before try to dump registers value.
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
|
|
By pass pullup DP in OTG fsm mode when do gadget connect, to let it handled
by OTG state machine.
This patch can fix the problem you found with my HNP polling patchset after
below 3 patches introduced:
467a78c usb: chipidea: udc: apply new usb_udc_vbus_handler interface
628ef0d usb: udc: add usb_udc_vbus_handler
dfea9c9 usb: udc: store usb_udc pointer in struct usb_gadget
Problem:
- Connect USB cable and MicroAB cable between two boards
- Boot up two boards
- load g_mass_storage at B-device side, the enumeration will success,
and A will see a usb mass-storage device
- load g_mass_storage at A-device side, the problem has occurred, the
connection will be lost at the beginning, then connect again.
This patch is based on
commit eff933c1d3a2e046492b3dfc86db813856553a29
(chipidea: pci: make it depends on NOP_USB_XCEIV)
on branch peter-usb-dev of
git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb.git
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
|
|
Regression in commit 2caa80e72b57c6216aec6f6a11fcfb4fec46daa0
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Sun Feb 22 11:38:36 2015 +0100
drm: Fix deadlock due to getconnector locking changes
If the drm_connector_find() call returns NULL, we should no longer
call drm_modeset_unlock() to avoid locking imbalance.
Signed-off-by: Tommi Rantala <tt.rantala@gmail.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Simon reported the md io stats accounting issue:
"
I'm seeing "iostat -x -k 1" print this after a RAID1 rebuild on 4.0-rc5.
It's not abnormal other than it's 3-disk, with one being SSD (sdc) and
the other two being write-mostly:
Device: rrqm/s wrqm/s r/s w/s rkB/s wkB/s avgrq-sz avgqu-sz await r_await w_await svctm %util
sda 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
sdb 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
sdc 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
md0 0.00 0.00 0.00 0.00 0.00 0.00 0.00 345.00 0.00 0.00 0.00 0.00 100.00
md2 0.00 0.00 0.00 0.00 0.00 0.00 0.00 58779.00 0.00 0.00 0.00 0.00 100.00
md1 0.00 0.00 0.00 0.00 0.00 0.00 0.00 12.00 0.00 0.00 0.00 0.00 100.00
"
The cause is commit "18c0b223cf9901727ef3b02da6711ac930b4e5d4" uses the
generic_start_io_acct to account the disk stats rather than the open code,
but it also introduced the increase to .in_flight[rw] which is needless to
md. So we re-use the open code here to fix it.
Reported-by: Simon Kirby <sim@hostway.ca>
Cc: <stable@vger.kernel.org> 3.19
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
"The domainname can be specified as either a DNS host name, a
dotted-decimal IPv4 address, or a bracketed IPv6 address as specified
in [RFC2732]."
See https://bugzilla.redhat.com/show_bug.cgi?id=1206868
Reported-by: Kyle Brantley <kyle@averageurl.com>
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
"A series of fixup patches for version 4.0:
- one VB2 core fixup, when stopping the stream;
- one VB2 core fixup for dma-contig memory type;
- driver fixes at rtl28xx, s5p (tv, jpeg, mfc, soc-camera, sh_veu,
cx23885, gspca"
* tag 'media/v3.20-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] rtl28xxu: return success for unimplemented FE callback
[media] rtl2832: disable regmap register cache
[media] vb2: Fix dma_dir setting for dma-contig mem type
[media] media: s5p-mfc: fix broken pointer cast on 64bit arch
[media] media: s5p-mfc: fix mmap support for 64bit arch
[media] cx23885: fix querycap
[media] sh_veu: v4l2_dev wasn't set
[media] s5p-mfc: Fix NULL pointer dereference caused by not set q->lock
[media] s5p-jpeg: exynos3250: fix erroneous reset procedure
[media] s5p-tv: hdmi needs I2C support
[media] s5p-jpeg: Initialize cb and cr to zero
[media] media: fix gspca drivers build dependencies
[media] soc-camera: Fix devm_kfree() in soc_of_bind()
[media] media: atmel-isi: increase the burst length to improve the performance
[media] vb2: fix 'UNBALANCED' warnings when calling vb2_thread_stop()
|
|
Simple patch to make symbols static. Symbols that are not
shared with other parts of the kernel can be made static.
This change also removes several sparse complains.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Ajit Pal Singh <ajitpal.singh@st.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
Some temperature sensors only get updated every few seconds and while
waiting for the first irq reporting a (new) temperature to happen there
get_temp operand will return -EAGAIN as it does not have any data to report
yet.
Not logging an error in this case avoids messages like these from showing
up in dmesg on affected systems:
[ 1.219353] thermal thermal_zone0: failed to read out thermal zone 0
[ 2.015433] thermal thermal_zone0: failed to read out thermal zone 0
[ 2.416737] thermal thermal_zone0: failed to read out thermal zone 0
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
If a driver doesn't implement the master->handle_err() callback and an
SPI transfer fails, the kernel will crash with a NULL pointer
dereference:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = c0003000
[00000000] *pgd=80000040004003, *pmd=00000000
Internal error: Oops: 80000206 [#1] SMP ARM
Modules linked in:
CPU: 1 PID: 1 Comm: swapper/0 Not tainted 4.0.0-rc7-koelsch-05861-g1fc9fdd4add4f783 #1046
Hardware name: Generic R8A7791 (Flattened Device Tree)
task: eec359c0 ti: eec54000 task.ti: eec54000
PC is at 0x0
LR is at spi_transfer_one_message+0x1cc/0x1f0
Make the master->handle_err() callback optional to avoid the crash.
Also fix a spelling mistake in the callback documentation while we're at
it.
Fixes: b716c4ffc6a2b0bf ("spi: introduce master->handle_err() callback")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Make sure we're using the new macro, so our
resume signaling will always pass certification.
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Make sure we're using the new macro, so our
resume signaling will always pass certification.
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Make sure we're using the new macro, so our
resume signaling will always pass certification.
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Make sure we're using the new macro, so our
resume signaling will always pass certification.
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
While this driver was already using a 50ms resume
timeout, let's make sure everybody uses the same
macro so it's easy to fix later should anything
go wrong.
It also gives a more "stable" expectation to Linux
users.
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Make sure we're using the new macro, so our
resume signaling will always pass certification.
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Make sure we're using the new macro, so our
resume signaling will always pass certification.
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Make sure we're using the new macro, so our
resume signaling will always pass certification.
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Make sure we're using the new macro, so our
resume signaling will always pass certification.
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Make sure we're using the new macro, so our
resume signaling will always pass certification.
Based on original work by Bin Liu <Bin Liu <b-liu@ti.com>>
Cc: Bin Liu <b-liu@ti.com>
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Make sure we're using the new macro, so our
resume signaling will always pass certification.
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Felipe Balbi <balbi@ti.com>
|