| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Fix usb0 pin 19 -> 29 (matching ethernet1 pins and manual).
Pin 19 is used for ethernet0 on the Parallella board.
Fixes: add958cee967 ("pinctrl: Add driver for Zynq")
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Remove sh7372 PFC support as part of the sh7372 and Mackerel
legacy code removal.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add PFC support for the EMMA Mobile EV2 SoC including pin groups for
on-chip devices.
Signed-off-by: Niklas Söderlund <niso@kth.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Used to define pinmux configurations where the pinmux function have no
representation in the configuration registers but instead solely depends
on a group selection.
Signed-off-by: Niklas Söderlund <niso@kth.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This is a driver for the pinmux and GPIO controller available in
Amlogic Meson SoCs. It currently supports only Meson8, however the
common code should be generic enough to work also for other SoCs after
having defined the proper set of functions and groups.
GPIO interrupts are not supported at the moment due to lack of
documentation.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch fixes two checkpatch.pl warnings
WARNING: Error trailing white space
WARNING: MIssing blank line after declaration
Signed-off-by: Anjana Sasindran <anjanasasindran123@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Audio IPs on Exynos7 require gpios available in AUDIO
pin controller block. So adding the AUDIO pinctrl support.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add MLB+ 3-pin mode pin group to R8A7790 PFC driver.
Based on original patch by Andrey Gusakov <andrey.gusakov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add MLB+ 3-pin mode pin group to R8A7791 PFC driver.
Based on original patch by Andrey Gusakov <andrey.gusakov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The R8A7791 manual sometimes calls the signal MLB_CLK and sometimes MLB_CK; the
latter can only be encountered in the PFC section and is probably just a typo
(this signal is always called MLB_CLK in the R8A7790 manual). Fix occurences
of MLB_CK throughout the R8A7791 PFC driver.
Based on original patch by Andrey Gusakov <andrey.gusakov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
marco chip has been dropped, clear its support.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const. Make also
of_device_id array const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const. Make also
of_device_id array const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The A31s is a stripped down version of the A31, as such it is missing some
pins and some functions on some pins.
The new pinctrl-sun6i-a31s.c this commit adds is a copy of pinctrl-sun6i-a31s.c
with the missing pins and functions removed.
Note there is no a31s specific version of pinctrl-sun6i-a31-r.c, as the
prcm pins are identical between the A31 and the A31s.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
While working on pinctrl for the A31s, I noticed that function 4 of
PA15 - PA18 was missing, add these.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
USB and Power regulator on Exynos7 require gpios available
in BUS1 pin controller block.
So adding the BUS1 pinctrl support.
Signed-off-by: Naveen Krishna Ch <naveenkrishna.ch@gmail.com>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
New pin controllers such as ACPI-based may also have custom properties
to parse, and should be able to use generic pin config. Let's make the
code compile on !OF systems and rename members a bit to underscore it
is custom parameters and not necessarily DT parameters.
This fixes a build regression for x86_64 on the zeroday kernel builds.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Reviewed-and-tested-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Instead of the driver caring about implementation details like device
tree, just provide information about driver specific pinconf parameters
to pinconf-generic which takes care of parsing the DT.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Tested-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This adds a pin-control driver for Zynq.
Changes since v2:
- driver-specific DT properties are passed to the core in two arrays,
one for the actual DT parsing one for the debugfs representation.
Issue a compiler warning when the number of entries is not the same
for both arrays.
Changes since v1:
- fix EMIO_SD1_CD pin name
- add USB to pinmux options
changes since RFCv2:
- let Zynq select PINCTRL_ZYNQ. Boot hangs when pinctrl information is
present in DT but no driver available.
- add #defines to get rid of magical constants
- add commas at end of initializers
- separate changes in mach-zynq in separate patch
- add driver specific io-standard DT property
- refactored pinconf set function to not require arguments for
argument-less properties
- squash other patches in
- support for IO-standard property
- support for low-power mode property
- migration to pinconf_generic_dt_node_to_map_all()
- use newly created infrastructure to add pass driver-specific DT
params to pinconf-generic
changes since RFC:
- use syscon/regmap to access registers in SLCR space
- rebase to 3.18: rename enable -> set_mux
- add kernel-doc
- support pinconf
- supported attributes
- pin-bias: pull up, tristate, disable
- slew-rate: 0 == slow, 1 == fast; generic pinconf does not display
argument
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Additionally to the generic DT parameters, allow drivers to provide
driver-specific DT parameters to be used with the generic parser
infrastructure.
To achieve this 'struct pinctrl_desc' is extended to pass custom pinconf
option to the core. In order to pass this kind of information, the
related data structures - 'struct pinconf_generic_dt_params',
'pin_config_item' - are moved from pinconf internals to the
pinconf-generic header.
Additionally pinconfg-generic is refactored to not only iterate over the
generic pinconf parameters but also take the parameters into account
that are provided through the driver's 'struct pinctrl_desc'.
In particular 'pinconf_generic_parse_dt_config()' and
'pinconf_generic_dump' helpers are split into two parts each. In order
to have a more generic helper that can be used to process the generic
parameters as well as the driver-specific ones.
v2:
- fix typo
- add missing documentation for @conf_items member in struct
- rebase to pinctrl/devel: conflict in abx500
- rename _pinconf_generic_dump() to pinconf_generic_dump_one()
- removed '_' from _parse_dt_cfg()
- removed BUG_ONs, error condition is handled in if statements
- removed pinconf_generic_dump_group() & pinconf_generic_dump_pin
helpers
- fixed up corresponding call sites
- renamed pinconf_generic_dump() to pinconf_generic_dump_pins()
- added kernel-doc to pinconf_generic_dump_pins()
- add kernel-doc
- more verbose commit message
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
With the new 'groups' property, the DT parser can infer the map type
from the fact whether 'pins' or 'groups' is used to specify the pin
group to work on.
To maintain backwards compatibitliy with current usage of the DT
binding, this is only done when PIN_MAP_TYPE_INVALID is passed to the
parsing function as type.
Also, a new helper 'pinconf_generic_dt_node_to_map_all()' is introduced,
which can be used by drivers as generic callback for dt_node_to_map() to
leverage the new feature.
Changes since v2:
- rename dt_pin_specifier to subnode_target_type
- add additional comment in header file explaining passing an invalid
map type
- mention map_all() helper in commit message
Changes since RFC v2:
- none
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
When drivers are compiled in subdirectories the -DDEBUG flag need
to be passed in the individual Makefiles.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Suggested-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The MPP19 and MMP20 pins also have the ability to be muxed to the uart1
function.
Add this case to the pinctrl driver.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Before resuming from system sleep BIOS restores its view of pin
configuration. If we have configured some pins differently from that, for
instance some driver requested a pin as a GPIO but it was not in GPIO mode
originally, our view of the pin configuration will not match the hardware
state anymore.
This patch saves the pin configuration and interrupt mask registers on
suspend and restores them on exit. This should make sure that the
previously configured state is still in effect.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs fix from Al Viro:
"An embarrassing bug in lustre patches from this cycle ;-/"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
[regression] braino in "lustre: use is_root_inode()"
|
|
In one of the places (ll_md_blocking_ast()) we had open-coded
!is_root_inode(inode) and replaced it with is_root_inode(inode).
See the last chunk of f76c23:
- inode != inode->i_sb->s_root->d_inode)
+ is_root_inode(inode))
should've been
+ !is_root_inode(inode))
obviously...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Pull drm fixes from Dave Airlie:
"Xmas fixes pull:
core:
one atomic fix, revert the WARN_ON dumb buffers patch.
agp:
fixup Dave J.
nouveau:
fix 3.18 regression for old userspace
tegra fixes:
vblank and iommu fixes
amdkfd:
fix bugs shown by testing with userspace, init apertures once
msm:
hdmi fixes and cleanup
i915:
misc fixes
There is also a link ordering fix that I've asked to be cc'ed to you,
putting iommu before gpu, it fixes an issue with amdkfd when things
are all in the kernel, but I didn't like sending it via my tree
without discussion.
I'll probably be a bit on/off for a few weeks with pulls now, due to
holidays and LCA, so don't be surprised if stuff gets a bit backed up,
and things end up a bit large due to lag"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (28 commits)
Revert "drm/gem: Warn on illegal use of the dumb buffer interface v2"
agp: Fix up email address & attributions in AGP MODULE_AUTHOR tags
nouveau: bring back legacy mmap handler
drm/msm/hdmi: rework HDMI IRQ handler
drm/msm/hdmi: enable regulators before clocks to avoid warnings
drm/msm/mdp5: update irqs on crtc<->encoder link change
drm/msm: block incoming update on pending updates
drm/atomic: fix potential null ptr on plane enable
drm/msm: Deletion of unnecessary checks before the function call "release_firmware"
drm/msm: Deletion of unnecessary checks before two function calls
drm/tegra: dc: Select root window for event dispatch
drm/tegra: gem: Use the proper size for GEM objects
drm/tegra: gem: Flush buffer objects upon allocation
drm/tegra: dc: Fix a potential race on page-flip completion
drm/tegra: dc: Consistently use the same pipe
drm/irq: Add drm_crtc_vblank_count()
drm/irq: Add drm_crtc_handle_vblank()
drm/irq: Add drm_crtc_send_vblank_event()
drm/i915: Disable PSMI sleep messages on all rings around context switches
drm/i915: Force the CS stall for invalidate flushes
...
|
|
Pull ipmi driver bugfixes from Corey Minyard:
"Fix two bugs:
One that lockdep turned up, I didn't go far enough with cleanup of
attributes for IPMI. This has been there a long time; my previous fix
of this didn't fix all the attributes.
One fix for some arches that need an explicit linux/ctype.h for
isspace()"
* tag 'for-linus-2' of git://git.code.sf.net/p/openipmi/linux-ipmi:
ipmi: Fix compile issue with isspace()
ipmi: Finish cleanup of BMC attributes
|
|
This reverts commit 355a70183848f21198e9f6296bd646df3478a26d.
This had some bad side effects under normal operation, and should
have been dropped earlier.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
git://people.freedesktop.org/~gabbayo/linux into drm-fixes
- Display MEC fw version in topology. Without this, the HSA userspace
stack is broken.
- Init apertures information only once per process
* tag 'amdkfd-fixes-2014-12-23' of git://people.freedesktop.org/~gabbayo/linux:
amdkfd: init aperture once per process
amdkfd: Display MEC fw version in topology node
drm/radeon: Add implementation of get_fw_version
drm/amd: Add get_fw_version to kfd-->kgd interface
|
|
- Remove soon-to-be-dead @redhat address.
- Jeff Hartmann wrote the bulk of the original backend code, and should
at least get a mention in the MODULE_AUTHOR for backend.o
- Various people at Intel have done a lot more work than myself on the
intel-* drivers, so again, mention that.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
"Thre stable fixes and one fix for a regression introduced during 3.19
merge:
- Fix inability to discard used space when the thin-pool target is in
out-of-data-space mode and also transition the thin-pool back to
write mode once free space is made available.
- Fix DM core bio-based end_io bug that prevented proper
post-processing of the error code returned from the block layer.
- Fix crash in DM thin-pool due to thin device being added to the
pool's active_thins list before properly initializing the thin
device's refcount"
* tag 'dm-3.19-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm: fix missed error code if .end_io isn't implemented by target_type
dm thin: fix crash by initializing thin device's refcount and completion earlier
dm thin: fix missing out-of-data-space to write mode transition if blocks are released
dm thin: fix inability to discard blocks when in out-of-data-space mode
|
|
git://people.freedesktop.org/~tagr/linux into drm-fixes
drm/tegra: Fixes for v3.19-rc1
This is a set of fixes for two regressions and one bug in the IOMMU
mapping code. It turns out that all of these issues turn up primarily
on Tegra30 hardware. The IOMMU mapping bug only manifests on buffers
that aren't multiples of the page size. I happened to be testing HDMI
with 1080p while writing the code and framebuffers for that happen to
fit exactly within 2025 pages of 4 KiB each.
One of the regressions is caused by the IOMMU code allocating pages from
shmem which can have associated cache lines. If the pages aren't flushed
then these cache lines may be flushed later on and cause framebuffer
corruption. I'm not sure why I didn't see this before. Perhaps the board
that I was using had enough RAM so that the pages shmem would hand out
had a better chance of being unused. Or maybe I didn't look too closely.
The fix for this is to fake up an SG table so that it can be passed to
the DMA API. Ideally this would use drm_clflush_*(), but implementing
that for ARM causes DRM to fail to build as a module since some of the
low-level cache maintenance functions aren't exported. Hopefully we can
get a suitable API exported on ARM for the next release.
The second regression is caused by a mismatch between the hardware pipe
number and the CRTC's DRM index. These were used inconsistently, which
could cause one code location to call drm_vblank_get() with a different
pipe than the corresponding drm_vblank_put(), thereby causing the
reference count to become unbalanced. Alexandre also reported a possible
race condition related to this, which this series also fixes.
* tag 'drm/tegra/for-3.19-rc1-fixes' of git://people.freedesktop.org/~tagr/linux:
drm/tegra: dc: Select root window for event dispatch
drm/tegra: gem: Use the proper size for GEM objects
drm/tegra: gem: Flush buffer objects upon allocation
drm/tegra: dc: Fix a potential race on page-flip completion
drm/tegra: dc: Consistently use the same pipe
drm/irq: Add drm_crtc_vblank_count()
drm/irq: Add drm_crtc_handle_vblank()
drm/irq: Add drm_crtc_send_vblank_event()
|
|
git://anongit.freedesktop.org/drm-intel into drm-fixes
misc i915 fixes.
* tag 'drm-intel-next-fixes-2014-12-17' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Disable PSMI sleep messages on all rings around context switches
drm/i915: Force the CS stall for invalidate flushes
drm/i915: Invalidate media caches on gen7
drm/i915: sanitize RPS resetting during GPU reset
drm/i915: move RPS PM_IER enabling to gen6_enable_rps_interrupts
drm/i915: vlv: fix IRQ masking when uninstalling interrupts
|
|
git://anongit.freedesktop.org/drm-intel into drm-fixes
Yeah a pull for one patch is a bit overkill but I started to assemble the
various patches for 3.20 in a branch for atomic props/ioctl and didn't
realize that this bugfix here at the beginnning of the branch should be in
3.19 (because msm is using the helpers arleady). So if you'd merge we'd
have it twice or or I need to shuffle branches again. Can do if you want.
* tag 'topic/atomic-fixes-2014-12-17' of git://anongit.freedesktop.org/drm-intel:
drm/atomic: fix potential null ptr on plane enable
|
|
git://people.freedesktop.org/~robclark/linux into drm-fixes
A few msm fixes for 3.19:
* hdmi regulators fix
* hdmi fix for spurious HPD interrupts
* fix for sync atomic update after async update (which could show
up with a setcrtc following a pageflip)
* couple little Coccinelle cleanups
* 'msm-fixes-3.19' of git://people.freedesktop.org/~robclark/linux:
drm/msm/hdmi: rework HDMI IRQ handler
drm/msm/hdmi: enable regulators before clocks to avoid warnings
drm/msm/mdp5: update irqs on crtc<->encoder link change
drm/msm: block incoming update on pending updates
drm/msm: Deletion of unnecessary checks before the function call "release_firmware"
drm/msm: Deletion of unnecessary checks before two function calls
|
|
nouveau userspace back at 1.0.1 used to call the X server
DRIOpenDRMMaster interface even for DRI2 (doh!), this attempts
to map the sarea and fails if it can't.
Since 884c6dabb0eafe7227f099c9e78e514191efaf13 from Daniel,
this fails, but only ancient drivers would see it.
Revert the nouveau bits of that fix.
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: <stable@vger.kernel.org> # 3.18
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Some arches don't get ctypes.h included from these includes, so add
it explicitly.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
|
|
The previous cleanup of BMC attributes left a few holes, and if
you run with lockdep debugging with a BMC with the proper attributes,
you could get a warning.
This patch removes all the unused attributes from the BMC structure,
since they are all declared in the .data section now. It makes
the attributes all static. It fixes the referencing of the
attributes in a couple of cases that dynamically added the files
depending on BMC information.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Huang Ying <ying.huang@intel.com>
Tested-by: Alexei Starovoitov <ast@plumgrid.com>
|
|
git://git.linaro.org/people/mike.turquette/linux
Pull clk framework updates from Mike Turquette:
"This is much later than usual due to several last minute bugs that had
to be addressed. As usual the majority of changes are new drivers and
modifications to existing drivers. The core recieved many fixes along
with the groundwork for several large changes coming in the future
which will better parition clock providers from clock consumers"
* tag 'clk-for-linus-3.19' of git://git.linaro.org/people/mike.turquette/linux: (86 commits)
clk: samsung: Fix Exynos 5420 pinctrl setup and clock disable failure due to domain being gated
ARM: OMAP3: clock: fix boot breakage in legacy mode
ARM: OMAP2+: clock: fix DPLL code to use new determine rate APIs
clk: Really fix deadlock with mmap_sem
clk: mmp: fix sparse non static symbol warning
clk: Change clk_ops->determine_rate to return a clk_hw as the best parent
clk: change clk_debugfs_add_file to take a struct clk_hw
clk: Don't expose __clk_get_accuracy
clk: Don't try to use a struct clk* after it could have been freed
clk: Remove unused function __clk_get_prepare_count
clk: samsung: Fix double add of syscore ops after driver rebind
clk: samsung: exynos4: set parent of sclk_hdmiphy to hdmi
clk: samsung: exynos4415: Fix build with PM_SLEEP disabled
clk: samsung: remove unnecessary inclusion of header files from clk.h
clk: samsung: remove unnecessary CONFIG_OF from clk.c
clk: samsung: Spelling s/bwtween/between/
clk: rockchip: Add support for the mmc clock phases using the framework
clk: rockchip: add bindings for the mmc clocks
clk: rockchip: rk3288 export i2s0_clkout for use in DT
clk: rockchip: use clock ID for DMC (memory controller) on rk3288
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull more i2c updates from Wolfram Sang:
"Included are two bugfixes needing some bigger refactoring (sh_mobile:
deferred probe with DMA, mv64xxx: fix offload support) and one
deprecated driver removal I thought would go in via ppc but I
misunderstood. It has a proper ack from BenH"
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: sh_mobile: fix uninitialized var when debug is enabled
macintosh: therm_pm72: delete deprecated driver
i2c: sh_mobile: I2C_SH_MOBILE should depend on HAS_DMA
i2c: sh_mobile: rework deferred probing
i2c: sh_mobile: refactor DMA setup
i2c: mv64xxx: rework offload support to fix several problems
i2c: mv64xxx: use BIT() macro for register value definitions
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI update from James Bottomley:
"This is a much shorter set of patches that were on the go but didn't
make it in to the early pull request for the merge window. It's
really a set of bug fixes plus some final cleanup work on the new tag
queue API"
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
storvsc: ring buffer failures may result in I/O freeze
ipr: set scsi_level correctly for disk arrays
ipr: add support for async scanning to speed up boot
scsi_debug: fix missing "break;" in SDEBUG_UA_CAPACITY_CHANGED case
scsi_debug: take sdebug_host_list_lock when changing capacity
scsi_debug: improve driver description in Kconfig
scsi_debug: fix compare and write errors
qla2xxx: fix race in handling rport deletion during recovery causes panic
scsi: blacklist RSOC for Microsoft iSCSI target devices
scsi: fix random memory corruption with scsi-mq + T10 PI
Revert "[SCSI] mpt3sas: Remove phys on topology change"
Revert "[SCSI] mpt2sas: Remove phys on topology change."
esas2r: Correct typos of "validate" in a comment
fc: FCP_PTA_SIMPLE is 0
ibmvfc: remove unused tag variable
scsi: remove MSG_*_TAG defines
scsi: remove scsi_set_tag_type
scsi: remove scsi_get_tag_type
scsi: never drop to untagged mode during queue ramp down
scsi: remove ->change_queue_type method
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull CONFIG_PM_RUNTIME elimination from Rafael Wysocki:
"This removes the last few uses of CONFIG_PM_RUNTIME introduced
recently and makes that config option finally go away.
CONFIG_PM will be available directly from the menu now and also it
will be selected automatically if CONFIG_SUSPEND or CONFIG_HIBERNATION
is set"
* tag 'pm-config-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM: Eliminate CONFIG_PM_RUNTIME
tty: 8250_omap: Replace CONFIG_PM_RUNTIME with CONFIG_PM
sound: sst-haswell-pcm: Replace CONFIG_PM_RUNTIME with CONFIG_PM
spi: Replace CONFIG_PM_RUNTIME with CONFIG_PM
|
|
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs pile #3 from Al Viro:
"Assorted fixes and patches from the last cycle"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
[regression] chunk lost from bd9b51
vfs: make mounts and mountstats honor root dir like mountinfo does
vfs: cleanup show_mountinfo
init: fix read-write root mount
unfuck binfmt_misc.c (broken by commit e6084d4)
vm_area_operations: kill ->migrate()
new helper: iter_is_iovec()
move_extent_per_page(): get rid of unused w_flags
lustre: get rid of playing with ->fs
btrfs: filp_open() returns ERR_PTR() on failure, not NULL...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending
Pull SCSI target fixes from Nicholas Bellinger:
"The highlights this merge window include:
- Allow target fabric drivers to function as built-in. (Roland)
- Fix tcm_loop multi-TPG endpoint nexus bug. (Hannes)
- Move per device config_item_type into se_subsystem_api, allowing
configfs attributes to be defined at module_init time. (Jerome +
nab)
- Convert existing IBLOCK/FILEIO/RAMDISK/PSCSI/TCMU drivers to use
external configfs attributes. (nab)
- A number of iser-target fixes related to active session + network
portal shutdown stability during extended stress testing. (Sagi +
Slava)
- Dynamic allocation of T10-PI contexts for iser-target, fixing a
potentially bogus iscsi_np->tpg_np pointer reference in >= v3.14
code. (Sagi)
- iser-target performance + scalability improvements. (Sagi)
- Fixes for SPC-4 Persistent Reservation AllRegistrants spec
compliance. (Ilias + James + nab)
- Avoid potential short kern_sendmsg() in iscsi-target for now until
Al's conversion to use msghdr iteration is merged post -rc1.
(Viro)
Also, Sagi has requested a number of iser-target patches (9) that
address stability issues he's encountered during extended stress
testing be considered for v3.10.y + v3.14.y code. Given the amount of
LOC involved, it will certainly require extra backporting effort.
Apologies in advance to Greg-KH & Co on this. Sagi and I will be
working post-merge to ensure they each get applied correctly"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (53 commits)
target: Allow AllRegistrants to re-RESERVE existing reservation
uapi/linux/target_core_user.h: fix headers_install.sh badness
iscsi-target: Fail connection on short sendmsg writes
iscsi-target: nullify session in failed login sequence
target: Avoid dropping AllRegistrants reservation during unregister
target: Fix R_HOLDER bit usage for AllRegistrants
iscsi-target: Drop left-over bogus iscsi_np->tpg_np
iser-target: Fix wc->wr_id cast warning
iser-target: Remove code duplication
iser-target: Adjust log levels and prettify some prints
iser-target: Use debug_level parameter to control logging level
iser-target: Fix logout sequence
iser-target: Don't wait for session commands from completion context
iser-target: Reduce CQ lock contention by batch polling
iser-target: Introduce isert_poll_budget
iser-target: Remove an atomic operation from the IO path
iser-target: Remove redundant call to isert_conn_terminate
iser-target: Use single CQ for TX and RX
iser-target: Centralize completion elements to a context
iser-target: Cast wr_id with uintptr_t instead of unsinged long
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 apic updates from Thomas Gleixner:
"After stopping the full x86/apic branch, I took some time to go
through the first block of patches again, which are mostly cleanups
and preparatory work for the irqdomain conversion and ioapic hotplug
support.
Unfortunaly one of the real problematic commits was right at the
beginning, so I rebased this portion of the pending patches without
the offenders.
It would be great to get this into 3.19. That makes reworking the
problematic parts simpler. The usual tip testing did not unearth any
issues and it is fully bisectible now.
I'm pretty confident that this wont affect the calmness of the xmas
season.
Changes:
- Split the convoluted io_apic.c code into domain specific parts
(vector, ioapic, msi, htirq)
- Introduce proper helper functions to retrieve irq specific data
instead of open coded dereferencing of pointers
- Preparatory work for ioapic hotplug and irqdomain conversion
- Removal of the non functional pci-ioapic driver
- Removal of unused irq entry stubs
- Make native_smp_prepare_cpus() preemtible to avoid GFP_ATOMIC
allocations for everything which is called from there.
- Small cleanups and fixes"
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
iommu/amd: Use helpers to access irq_cfg data structure associated with IRQ
iommu/vt-d: Use helpers to access irq_cfg data structure associated with IRQ
x86: irq_remapping: Use helpers to access irq_cfg data structure associated with IRQ
x86, irq: Use helpers to access irq_cfg data structure associated with IRQ
x86, irq: Make MSI and HT_IRQ indepenent of X86_IO_APIC
x86, irq: Move IRQ initialization routines from io_apic.c into vector.c
x86, irq: Move IOAPIC related declarations from hw_irq.h into io_apic.h
x86, irq: Move HT IRQ related code from io_apic.c into htirq.c
x86, irq: Move PCI MSI related code from io_apic.c into msi.c
x86, irq: Replace printk(KERN_LVL) with pr_lvl() utilities
x86, irq: Make UP version of irq_complete_move() an inline stub
x86, irq: Move local APIC related code from io_apic.c into vector.c
x86, irq: Introduce helpers to access struct irq_cfg
x86, irq: Protect __clear_irq_vector() with vector_lock
x86, irq: Rename local APIC related functions in io_apic.c as apic_xxx()
x86, irq: Refine hw_irq.h to prepare for irqdomain support
x86, irq: Convert irq_2_pin list to generic list
x86, irq: Kill useless parameter 'irq_attr' of IO_APIC_get_PCI_irq_vector()
x86, irq, acpi: Get rid of special handling of GSI for ACPI SCI
x86, irq: Introduce helper to check whether an IOAPIC has been registered
...
|
|
Having switched over all of the users of CONFIG_PM_RUNTIME to use
CONFIG_PM directly, turn the latter into a user-selectable option
and drop the former entirely from the tree.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull NOHZ update from Thomas Gleixner:
"Remove the call into the nohz idle code from the fake 'idle' thread in
the powerclamp driver along with the export of those functions which
was smuggeled in via the thermal tree. People have tried to hack
around it in the nohz core code, but it just violates all rightful
assumptions of that code about the only valid calling context (i.e.
the proper idle task).
The powerclamp trainwreck will still work, it just wont get the
benefit of long idle sleeps"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tick/powerclamp: Remove tick_nohz_idle abuse
|