| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Commit b91ecb00 ("gigaset: include cleanup cleanup") removed an implicit
sched.h inclusion that came in via slab.h, and caused various compile
problems as a result.
This should fix it.
Reported-by: Ingo Molnar <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Add a loop to wait for the controller to finish a locally-initiated CSR
lock operation. Google shows some occurrences of the "swap not done
yet" message which might indicate that some OHCI controllers are not
fast enough to do the lock/swap in the time needed for one PCI access.
This also correctly handles the case where the lock operation did not
finish, instead of silently returning an uninitialized value.
Signed-off-by: Clemens Ladisch <[email protected]>
Signed-off-by: Stefan Richter <[email protected]>
|
|
We must compute the offset from the CSR register base with the
full 48 address bits to prevent matching with addresses whose
lower 32 bits happen to be equal with one of the specially
handled registers.
Signed-off-by: Clemens Ladisch <[email protected]>
Signed-off-by: Stefan Richter <[email protected]>
|
|
Returning -EIO for all errors would not allow clients to determine if
the resource allocation process itself failed, or if the resources are
not available. (The latter information is needed by CMP to synchronize
restoring of overlayed connections after a bus reset.)
Signed-off-by: Clemens Ladisch <[email protected]>
Signed-off-by: Stefan Richter <[email protected]>
|
|
If there is a permanent error condition when communicating with the IRM,
after the sixth error, the retry variable will be decremented to -1.
If, in this case, the bits in channels_mask are not yet exhausted, the
next channel is retried 2^32 times.
To fix this, check that retry is never decremented beyond zero.
Signed-off-by: Clemens Ladisch <[email protected]>
Signed-off-by: Stefan Richter <[email protected]>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
gigaset: include cleanup cleanup
packet : remove init_net restriction
WAN: flush tx_queue in hdlc_ppp to prevent panic on rmmod hw_driver.
ip: Fix ip_dev_loopback_xmit()
net: dev_pick_tx() fix
fib: suppress lockdep-RCU false positive in FIB trie.
tun: orphan an skb on tx
forcedeth: fix tx limit2 flag check
iwlwifi: work around bogus active chains detection
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: add FireMV 2400 PCI ID.
drm/radeon/kms: allow R500 regs VAP_ALT_NUM_VERTICES and VAP_INDEX_OFFSET
drivers/gpu/radeon: Add MSPOS regs to safe list.
drm/radeon/kms: disable the tv encoder when tv/cv is not in use
drm/radeon/kms: adjust pll settings for tv
drm/radeon/kms: fix tv dac conflict resolver
drm/radeon/kms/evergreen: don't enable hdmi audio stuff
drm/radeon/kms/atom: fix dual-link DVI on DCE3.2/4.0
drm/radeon/kms: fix rs600 tlb flush
drm/radeon/kms: print GPU family and device id when loading
drm/radeon/kms: fix calculation of mipmapped 3D texture sizes
drm/radeon/kms: only change mode when coherent value changes.
drm/radeon/kms: more atom parser fixes (v2)
|
|
In the original code we used -ENODEV as the number of bytes to
copy_to_user() and we didn't release the locks.
Signed-off-by: Dan Carpenter <[email protected]>
Acked-by: Harald Welte <[email protected]>
Signed-off-by: Dominik Brodowski <[email protected]>
|
|
This patch fixes a memory leak by freeing priv in mc13783_regulator_remove
Signed-off-by: Axel Lin <[email protected]>
Cc: Sascha Hauer <[email protected]>
Cc: Liam Girdwood <[email protected]>
Cc: Mark Brown <[email protected]>
Cc: Samuel Ortiz <[email protected]>
Signed-off-by: Liam Girdwood <[email protected]>
|
|
[airlied: fix V_A_N_V to not be safe and fix check to make sure only r500
- bump userspace version]
Signed-off-by: Marek Olšák <[email protected]>
Signed-off-by: Dave Airlie <[email protected]>
|
|
Permits MSAA and D3D-style rasterization.
[airlied: add rs600]
Signed-off-by: Corbin Simpson <[email protected]>
Signed-off-by: Dave Airlie <[email protected]>
|
|
Switching between TV and VGA caused VGA to break on some systems
since the TV encoder was left enabled when VGA was used.
fixes fdo bug 25520.
Signed-off-by: Alex Deucher <[email protected]>
Cc: stable <[email protected]>
Signed-off-by: Dave Airlie <[email protected]>
|
|
May fix fdo bug 26582.
Signed-off-by: Alex Deucher <[email protected]>
Signed-off-by: Dave Airlie <[email protected]>
|
|
On systems with the tv dac shared between DVI and TV,
we can only use the dac for one of the connectors.
However, when using a digital monitor on the DVI port,
you can use the dac for the TV connector just fine.
Check the use_digital status when resolving the conflict.
Fixes fdo bug 27649, possibly others.
Signed-off-by: Alex Deucher <[email protected]>
Cc: stable <[email protected]>
Signed-off-by: Dave Airlie <[email protected]>
|
|
Signed-off-by: Alex Deucher <[email protected]>
Signed-off-by: Dave Airlie <[email protected]>
|
|
Got broken during the evergreen merge.
Fixes fdo bug 27001.
Signed-off-by: Alex Deucher <[email protected]>
Signed-off-by: Dave Airlie <[email protected]>
|
|
Typo in in flush leaded to no flush of the RS600 tlb which
ultimately leaded to massive system ram corruption, with
this patch everythings seems to work properly.
Signed-off-by: Jerome Glisse <[email protected]>
Cc: stable <[email protected]>
Signed-off-by: Dave Airlie <[email protected]>
|
|
This will help figuring out GPU when looking at bugs log.
Signed-off-by: Jerome Glisse <[email protected]>
Signed-off-by: Dave Airlie <[email protected]>
|
|
Current code is definitely crap: Largest pitch allowed spills into
the TILING_Y bit of the fence registers ... :(
I've rewritten the limits check under the assumption that 3rd gen hw
has a 3d pitch limit of 8kb (like 2nd gen). This is supported by an
otherwise totally misleading XXX comment.
This bug mostly resulted in tiling-corrupted pixmaps because the kernel
allowed too wide buffers to be tiled. Bug brought to the light by the
xf86-video-intel 2.11 release because that unconditionally enabled
tiling for pixmaps, relying on the kernel to check things. Tiling for
the framebuffer was not affected because the ddx does some additional
checks there ensure the buffer is within hw-limits.
v2: Instead of computing the value that would be written into the
hw fence registers and then checking the limits simply check whether
the stride is above the 8kb limit. To better document the hw, add
some WARN_ONs in i915_write_fence_reg like I've done for the i830
case (using the right limits).
Signed-off-by: Daniel Vetter <[email protected]>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=27449
Tested-by: Alexander Lam <[email protected]>
Cc: [email protected]
Signed-off-by: Eric Anholt <[email protected]>
|
|
we used to set the DIDL in the output device detected order.
But some BIOSes requires it to be initialized in the ACPI device order.
e.g. the value of the first field in DIDL stands for the first
ACPI video output device in ACPI namespace.
Now we initialize the DIDL using the device id, i.e. _ADR return value,
of each ACPI video device, if it is not 0.
https://bugzilla.kernel.org/show_bug.cgi?id=15054
Signed-off-by: Zhang Rui <[email protected]>
Signed-off-by: Eric Anholt <[email protected]>
|
|
pci.ids and the datasheet both say it's 358e, not 35e8.
Signed-off-by: Adam Jackson <[email protected]>
Signed-off-by: Eric Anholt <[email protected]>
|
|
IS_MOBILE() catches 85x, so we'd always try to use the 9xx FIFO sizing;
since there's an explicit 85x version, this seems wrong.
v2: Handle 830m correctly too.
Signed-off-by: Adam Jackson <[email protected]>
Reviewed-by: Eric Anholt <[email protected]>
Signed-off-by: Eric Anholt <[email protected]>
|
|
Commit 5a0e3ad causes slab.h to be included twice in many of the
Gigaset driver's source files, first via the common include file
gigaset.h and then a second time directly. Drop the spares, and
use the opportunity to clean up a few more similar cases.
Impact: cleanup, no functional change
Signed-off-by: Tilman Schmidt <[email protected]>
CC: Tejun Heo <[email protected]>
Acked-by: Tejun Heo <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: Ignore LVDS EDID when it is unavailabe or invalid
drm/i915: Add no_lvds entry for the Clientron U800
drm/i915: Rename many remaining uses of "output" to encoder or connector.
drm/i915: Rename intel_output to intel_encoder.
agp/intel: intel_845_driver is an agp driver!
drm/i915: introduce to_intel_bo helper
drm/i915: Disable FBC on 915GM and 945GM.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: EC: Limit burst to 64 bits
|
|
Use local_irq_restore in this error-handling case just like in the one just
below.
A simplified version of the semantic patch that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
expression E1;
identifier f;
@@
f (...) { <+...
* local_irq_save (E1,...);
... when != E1
* return ...;
...+> }
// </smpl>
Signed-off-by: Julia Lawall <[email protected]>
Signed-off-by: Dominik Brodowski <[email protected]>
|
|
Many PCMCIA GPRS modems like: Onda Edge N100E, Novaway PC98 (OEM SPC98Z),
Rovermate Edgus Adaptmate-039 and others have same construction and
identification:
lspcmcia -vvv
Product Name: Generic Modem: MD55x 1.00 Serial number: xxxxx-xxx
Identification: manf_id: 0x015d card_id: 0x4c45
function: 2 (serial)
prod_id(1): "Generic" (0xc49e4731)
prod_id(2): "Modem: MD55x" (0x8913b110)
prod_id(3): "1.00" (0x83dbf271)
prod_id(4): "Serial number: xxxxx-xxx" (0x73ee9514)
Serial connection to GSM module based on Elan VPU16551 PCMCIA UART with
datasheet recommeded 14.7456MHz crystal oscillator.
By default serial_cs set UART clock == 1843200 Hz
For correct work need set clock 14745600 Hz.
This quirk already present in driver, only need add device in quirk list.
Signed-off-by: Timur Maximov <[email protected]>
Acked-by: Alan Cox <[email protected]>
Signed-off-by: Dominik Brodowski <[email protected]>
|
|
pccard_validate_cis() nowadays destroys the CIS cache. Therefore,
calling it after card setup should be avoided. We can't control
the deprecated PCMCIA ioctl (which is only used on ARM nowadays),
but we can avoid -- and report -- any other calls.
Signed-off-by: Dominik Brodowski <[email protected]>
|
|
tx_queue is used as a temporary queue when not allowed to queue skb
directly to the hw device driver (which may sleep). Most paths flush
it before returning, but ppp_start() currently cannot. Make sure we
don't leave skbs pointing to a non-existent device.
Thanks to Michael Barkowski for reporting this problem.
Signed-off-by: Krzysztof Hałasa <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
|
|
access_bit_width field is u8 in ACPICA, thus 256 value written to it
becomes 0, causing divide by zero later.
Proper fix would be to remove access_bit_width at all, just because
we already have access_byte_width, which is access_bit_width / 8.
Limit access width to 64 bit for now.
https://bugzilla.kernel.org/show_bug.cgi?id=15749
fixes regression caused by the fix for:
https://bugzilla.kernel.org/show_bug.cgi?id=14667
Signed-off-by: Alexey Starikovskiy <[email protected]>
Signed-off-by: Len Brown <[email protected]>
|
|
Correct fix for the "ioremap() causes build failure on S390" should have been
a dependancy on HAS_IOMEM. So we add this dependancy also (and leave the driver
in the ARM section for now).
Signed-off-by: Geert Uytterhoeven <[email protected]>
Signed-off-by: Wim Van Sebroeck <[email protected]>
|
|
When shutting down the watchdog timer, special care must be taken
not to overwrite other bits in the register, as it may be shared
with other peripherals.
For example, on the Arcom Vulcan, the register is shared between
the watchdog and the PCI reset line...
Signed-off-by: Marc Zyngier <[email protected]>
Signed-off-by: Wim Van Sebroeck <[email protected]>
|
|
A previous fix changed the WDTP function to use the period directly,
rather than subtracting from 63. However the mask generation was
not changed, so the mask was coming out as 0. This patch fixes it.
Signed-off-by: Luuk Paulussen <[email protected]>
Signed-off-by: Wim Van Sebroeck <[email protected]>
|
|
This patch allows Watchdog timer to be selected for OMAP4 by fixing
Kconfig entry
Signed-off-by: Santosh Shilimkar <[email protected]>
Signed-off-by: Wim Van Sebroeck <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
firewire: cdev: change license of exported header files to MIT license
firewire: cdev: comment fixlet
firewire: cdev: iso packet documentation
firewire: cdev: fix information leak
firewire: cdev: require quadlet-aligned headers for transmit packets
firewire: cdev: disallow receive packets without header
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: wacom - switch mode upon system resume
Revert "Input: wacom - merge out and in prox events"
Input: matrix_keypad - allow platform to disable key autorepeat
Input: ALPS - add signature for HP Pavilion dm3 laptops
Input: i8042 - spelling fix
Input: sparse-keymap - implement safer freeing of the keymap
Input: update the status of the Multitouch X driver project
Input: clarify the no-finger event in multitouch protocol
Input: bcm5974 - retract efi-broken suspend_resume
Input: sparse-keymap - free the right keymap on error
|
|
When Wacom devices wake up from a sleep, the switch mode command
(wacom_query_tablet_data) is needed before wacom_open is called.
wacom_query_tablet_data should not be executed inside wacom_open
since wacom_open is called more than once during probe.
wacom_retrieve_hid_descriptor is removed from wacom_resume due
to the fact that the required descriptors are stored properly
upon system resume.
Reported-and-tested-by: Anton Anikin <[email protected]>
Signed-off-by: Ping Cheng <[email protected]>
Cc: [email protected]
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
Size needs to be calculated after manipulating with the start value.
Reported-by: Komuro <[email protected]>
Signed-off-by: Dominik Brodowski <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: (applesmc) Switch maintainers
hwmon: (applesmc) Add iMac9,1 and MacBookPro2,2 support
hwmon: (it87) Invalidate cache on temperature sensor change
hwmon: (it87) Properly handle wrong sensor type requests
hwmon: (it87) Don't arbitrarily enable temperature channels
hwmon: (sht15) Properly handle the case CONFIG_REGULATOR=n
hwmon: (sht15) Fix sht15_calc_temp interpolation function
|
|
Add the iMac9,1 and the MacBookPro2,2 temperature sensors to hwmon
driver applesmc to fix kernel bug #14429:
https://bugzilla.kernel.org/show_bug.cgi?id=14429
Signed-off-by: Justin P. Mattock <[email protected]>
Acked-by: Nicolas Boichat <[email protected]>
Signed-off-by: Jean Delvare <[email protected]>
|
|
When any temperature sensor type is changed, the corresponding
temperature value needs to be updated. The register caching mechanism
may delay this update, so we want to invalidate the cache to force an
immediate update.
Signed-off-by: Jean Delvare <[email protected]>
|
|
Currently, if someone tries to set the thermal sensor type to an
unsupported value, subsequent accesses to the chip may temporarily
show the sensor in question as disabled. Use a temporary variable
and only update the cached value on success, to prevent such
confusion.
Signed-off-by: Jean Delvare <[email protected]>
|
|
Temperature channels can be used in 2 different modes (thermistor and
thermal diode) and we don't know which one, if any, is correct for
every given board. So don't arbitrarily choose one. Instead, leave the
temperature channels untouched. They can be configured from user-space
if needed anyway.
Signed-off-by: Jean Delvare <[email protected]>
|
|
When CONFIG_REGULATOR isn't set, regulator_get_voltage() returns 0.
Properly handle this case by not trusting the value.
Reported-by: Jerome Oufella <[email protected]>
Signed-off-by: Jean Delvare <[email protected]>
Cc: Jonathan Cameron <[email protected]>
Acked-by: Mark Brown <[email protected]>
Cc: [email protected]
|
|
I discovered two issues.
First the previous sht15_calc_temp() loop did not iterate through the
temppoints array since the (data->supply_uV > temppoints[i - 1].vdd)
test is always true in this direction.
Also the two-points linear interpolation function was returning biased
values due to a stray division by 1000 which shouldn't be there.
[JD: Also change the default value for d1 from 0 to something saner.]
Signed-off-by: Jerome Oufella <[email protected]>
Acked-by: Jonathan Cameron <[email protected]>
Signed-off-by: Jean Delvare <[email protected]>
Cc: [email protected]
|
|
This is a partial revert of 4cd8b5e2a159 "lguest: use KVM hypercalls";
we revert to using (just as questionable but more reliable) int $15 for
hypercalls. I didn't revert the register mapping, so we still use the
same calling convention as kvm.
KVM in more recent incarnations stopped injecting a fault when a guest
tried to use the VMCALL instruction from ring 1, so lguest under kvm
fails to make hypercalls. It was nice to share code with our KVM
cousins, but this was overreach.
Signed-off-by: Rusty Russell <[email protected]>
Cc: Matias Zabaljauregui <[email protected]>
Cc: Avi Kivity <[email protected]>
|
|
It's only used by cmpxchg8b_emu (see db677ffa5f5a for the gory
details), and fixing that to be paravirt aware would be more work than
simply ignoring it (and AFAICT only help lguest). This makes lguest
work on machines which have cmpxchg8b, for kernels compiled for older
processors.
(We can't emulate it properly: the popf which expects to restore interrupts
does not trap).
Signed-off-by: Rusty Russell <[email protected]>
Cc: Jeremy Fitzhardinge <[email protected]>
Cc: [email protected]
|
|
The following situation was observed in the field:
tap1 sends packets, tap2 does not consume them, as a result
tap1 can not be closed. This happens because
tun/tap devices can hang on to skbs undefinitely.
As noted by Herbert, possible solutions include a timeout followed by a
copy/change of ownership of the skb, or always copying/changing
ownership if we're going into a hostile device.
This patch implements the second approach.
Note: one issue still remaining is that since skbs
keep reference to tun socket and tun socket has a
reference to tun device, we won't flush backlog,
instead simply waiting for all skbs to get transmitted.
At least this is not user-triggerable, and
this was not reported in practice, my assumption is
other devices besides tap complete an skb
within finite time after it has been queued.
A possible solution for the second issue
would not to have socket reference the device,
instead, implement dev->destructor for tun, and
wait for all skbs to complete there, but this
needs some thought, probably too risky for 2.6.34.
Signed-off-by: Michael S. Tsirkin <[email protected]>
Tested-by: Yan Vugenfirer <[email protected]>
Acked-by: Herbert Xu <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|