| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
It appears that GPIO ACPI library uses ACPI debounce values directly.
However, the GPIO library APIs expect the debounce timeout to be in
microseconds.
Convert ACPI value of debounce to microseconds.
While at it, document this detail where it is appropriate.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=215664
Reported-by: Kai-Heng Feng <[email protected]>
Fixes: 8dcb7a15a585 ("gpiolib: acpi: Take into account debounce settings")
Signed-off-by: Andy Shevchenko <[email protected]>
Tested-by: Kai-Heng Feng <[email protected]>
Reviewed-by: Mika Westerberg <[email protected]>
Signed-off-by: Bartosz Golaszewski <[email protected]>
|
|
Some GPIO lines have stopped working after the patch
commit 2ab73c6d8323f ("gpio: Support GPIO controllers without pin-ranges")
And this has supposedly been fixed in the following patches
commit 89ad556b7f96a ("gpio: Avoid using pin ranges with !PINCTRL")
commit 6dbbf84603961 ("gpiolib: Don't free if pin ranges are not defined")
But an erratic behavior where some GPIO lines work while others do not work
has been introduced.
This patch reverts those changes so that the sysfs-gpio interface works
properly again.
Signed-off-by: Marcelo Roberto Jimenez <[email protected]>
Signed-off-by: Bartosz Golaszewski <[email protected]>
|
|
Add the number of interrupts per bank for Tegra241 (Grace) to
fix the probe failure.
Fixes: d1056b771ddb ("gpio: tegra186: Add support for Tegra241")
Signed-off-by: Akhil R <[email protected]>
Signed-off-by: Bartosz Golaszewski <[email protected]>
|
|
According to Documentation/driver-api/usb/URB.rst when a device
is unplugged usb_submit_urb() returns -ENODEV.
This error code propagates all the way up to usbnet_read_cmd() and
usbnet_write_cmd() calls inside the smsc95xx.c driver during
Ethernet cable unplug, unbind or reboot.
This causes the following errors to be shown on reboot, for example:
ci_hdrc ci_hdrc.1: remove, state 1
usb usb2: USB disconnect, device number 1
usb 2-1: USB disconnect, device number 2
usb 2-1.1: USB disconnect, device number 3
smsc95xx 2-1.1:1.0 eth1: unregister 'smsc95xx' usb-ci_hdrc.1-1.1, smsc95xx USB 2.0 Ethernet
smsc95xx 2-1.1:1.0 eth1: Failed to read reg index 0x00000114: -19
smsc95xx 2-1.1:1.0 eth1: Error reading MII_ACCESS
smsc95xx 2-1.1:1.0 eth1: __smsc95xx_mdio_read: MII is busy
smsc95xx 2-1.1:1.0 eth1: Failed to read reg index 0x00000114: -19
smsc95xx 2-1.1:1.0 eth1: Error reading MII_ACCESS
smsc95xx 2-1.1:1.0 eth1: __smsc95xx_mdio_read: MII is busy
smsc95xx 2-1.1:1.0 eth1: hardware isn't capable of remote wakeup
usb 2-1.4: USB disconnect, device number 4
ci_hdrc ci_hdrc.1: USB bus 2 deregistered
ci_hdrc ci_hdrc.0: remove, state 4
usb usb1: USB disconnect, device number 1
ci_hdrc ci_hdrc.0: USB bus 1 deregistered
imx2-wdt 30280000.watchdog: Device shutdown: Expect reboot!
reboot: Restarting system
Ignore the -ENODEV errors inside __smsc95xx_mdio_read() and
__smsc95xx_phy_wait_not_busy() and do not print error messages
when -ENODEV is returned.
Fixes: a049a30fc27c ("net: usb: Correct PHY handling of smsc95xx")
Signed-off-by: Fabio Estevam <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Clang static analysis reports this issue
qed_sriov.c:4727:19: warning: Assigned value is
garbage or undefined
ivi->max_tx_rate = tx_rate ? tx_rate : link.speed;
^ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
link is only sometimes set by the call to qed_iov_get_link()
qed_iov_get_link fails without setting link or returning
status. So change the decl to return status.
Fixes: 73390ac9d82b ("qed*: support ndo_get_vf_config")
Signed-off-by: Tom Rix <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
When the driver fails to register net device, it should free the DMA
region first, and then do other cleanup.
Signed-off-by: Zheyu Ma <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The skb->len field is read after the packet is sent to the network
stack. In the meantime, skb can be freed. This patch fixes this bug.
Fixes: c3e6b2c35b34 ("net: lantiq_xrx200: add ingress SG DMA support")
Reported-by: Eric Dumazet <[email protected]>
Signed-off-by: Aleksander Jan Bajkowski <[email protected]>
Acked-by: Hauke Mehrtens <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
qed_vf_hw_prepare()
The function dma_alloc_coherent() in qed_vf_hw_prepare() can fail, so
its return value should be checked.
Fixes: 1408cc1fa48c ("qed: Introduce VFs")
Reported-by: TOTE Robot <[email protected]>
Signed-off-by: Jia-Ju Bai <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The function dma_set_mask() in setup_hw() can fail, so its return value
should be checked.
Fixes: 1700fe1a10dc ("Add mISDN HFC PCI driver")
Reported-by: TOTE Robot <[email protected]>
Signed-off-by: Jia-Ju Bai <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Commit 76bfc7ccc2fa ("mmc: core: adjust polling interval for CMD1"),
significantly decreased the polling period from ~10-12ms into just a couple
of us. The purpose was to decrease the total time spent in the busy polling
loop, but unfortunate it has lead to problems, that causes eMMC cards to
never gets out busy and thus fails to be initialized.
To fix the problem, but also to try to keep some of the new improved
behaviour, let's start by using a polling period of 1-2ms, which then
increases for each loop, according to common polling loop in
__mmc_poll_for_busy().
Reported-by: Jean Rene Dawin <[email protected]>
Reported-by: H. Nikolaus Schaller <[email protected]>
Cc: Huijin Park <[email protected]>
Fixes: 76bfc7ccc2fa ("mmc: core: adjust polling interval for CMD1")
Signed-off-by: Ulf Hansson <[email protected]>
Tested-by: Jean Rene Dawin <[email protected]>
Tested-by: H. Nikolaus Schaller <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
When calling gnttab_end_foreign_access_ref() the returned value must
be tested and the reaction to that value should be appropriate.
In case of failure in xennet_get_responses() the reaction should not be
to crash the system, but to disable the network device.
The calls in setup_netfront() can be replaced by calls of
gnttab_end_foreign_access(). While at it avoid double free of ring
pages and grant references via xennet_disconnect_backend() in this case.
This is CVE-2022-23042 / part of XSA-396.
Reported-by: Demi Marie Obenour <[email protected]>
Signed-off-by: Juergen Gross <[email protected]>
Reviewed-by: Jan Beulich <[email protected]>
---
V2:
- avoid double free
V3:
- remove pointless initializer (Jan Beulich)
|
|
gnttab_end_foreign_access() is used to free a grant reference and
optionally to free the associated page. In case the grant is still in
use by the other side processing is being deferred. This leads to a
problem in case no page to be freed is specified by the caller: the
caller doesn't know that the page is still mapped by the other side
and thus should not be used for other purposes.
The correct way to handle this situation is to take an additional
reference to the granted page in case handling is being deferred and
to drop that reference when the grant reference could be freed
finally.
This requires that there are no users of gnttab_end_foreign_access()
left directly repurposing the granted page after the call, as this
might result in clobbered data or information leaks via the not yet
freed grant reference.
This is part of CVE-2022-23041 / XSA-396.
Reported-by: Simon Gaiser <[email protected]>
Signed-off-by: Juergen Gross <[email protected]>
Reviewed-by: Jan Beulich <[email protected]>
---
V4:
- expand comment in header
V5:
- get page ref in case of kmalloc() failure, too
|
|
Instead of __get_free_pages() and free_pages() use alloc_pages_exact()
and free_pages_exact(). This is in preparation of a change of
gnttab_end_foreign_access() which will prohibit use of high-order
pages.
This is part of CVE-2022-23041 / XSA-396.
Reported-by: Simon Gaiser <[email protected]>
Signed-off-by: Juergen Gross <[email protected]>
Reviewed-by: Jan Beulich <[email protected]>
---
V4:
- new patch
|
|
The usage of gnttab_end_foreign_access() in xenhcd_gnttab_done() is
not safe against a malicious backend, as the backend could keep the
I/O page mapped and modify it even after the granted memory page is
being used for completely other purposes in the local system.
So replace that use case with gnttab_try_end_foreign_access() and
disable the PV host adapter in case the backend didn't stop using the
granted page.
In xenhcd_urb_request_done() immediately return in case of setting
the device state to "error" instead of looking into further backend
responses.
Reported-by: Demi Marie Obenour <[email protected]>
Signed-off-by: Juergen Gross <[email protected]>
Reviewed-by: Jan Beulich <[email protected]>
---
V2:
- use gnttab_try_end_foreign_access()
|
|
Remove gnttab_query_foreign_access(), as it is unused and unsafe to
use.
All previous use cases assumed a grant would not be in use after
gnttab_query_foreign_access() returned 0. This information is useless
in best case, as it only refers to a situation in the past, which could
have changed already.
Signed-off-by: Juergen Gross <[email protected]>
Reviewed-by: Jan Beulich <[email protected]>
|
|
Using gnttab_query_foreign_access() is unsafe, as it is racy by design.
The use case in the gntalloc driver is not needed at all. While at it
replace the call of gnttab_end_foreign_access_ref() with a call of
gnttab_end_foreign_access(), which is what is really wanted there. In
case the grant wasn't used due to an allocation failure, just free the
grant via gnttab_free_grant_reference().
This is CVE-2022-23039 / part of XSA-396.
Reported-by: Demi Marie Obenour <[email protected]>
Signed-off-by: Juergen Gross <[email protected]>
Reviewed-by: Jan Beulich <[email protected]>
---
V3:
- fix __del_gref() (Jan Beulich)
|
|
It isn't enough to check whether a grant is still being in use by
calling gnttab_query_foreign_access(), as a mapping could be realized
by the other side just after having called that function.
In case the call was done in preparation of revoking a grant it is
better to do so via gnttab_try_end_foreign_access() and check the
success of that operation instead.
This is CVE-2022-23038 / part of XSA-396.
Reported-by: Demi Marie Obenour <[email protected]>
Signed-off-by: Juergen Gross <[email protected]>
Reviewed-by: Jan Beulich <[email protected]>
---
V2:
- use gnttab_try_end_foreign_access()
|
|
It isn't enough to check whether a grant is still being in use by
calling gnttab_query_foreign_access(), as a mapping could be realized
by the other side just after having called that function.
In case the call was done in preparation of revoking a grant it is
better to do so via gnttab_end_foreign_access_ref() and check the
success of that operation instead.
This is CVE-2022-23037 / part of XSA-396.
Reported-by: Demi Marie Obenour <[email protected]>
Signed-off-by: Juergen Gross <[email protected]>
Reviewed-by: Jan Beulich <[email protected]>
---
V2:
- use gnttab_try_end_foreign_access()
V3:
- don't use gnttab_try_end_foreign_access()
|
|
It isn't enough to check whether a grant is still being in use by
calling gnttab_query_foreign_access(), as a mapping could be realized
by the other side just after having called that function.
In case the call was done in preparation of revoking a grant it is
better to do so via gnttab_end_foreign_access_ref() and check the
success of that operation instead.
For the ring allocation use alloc_pages_exact() in order to avoid
high order pages in case of a multi-page ring.
If a grant wasn't unmapped by the backend without persistent grants
being used, set the device state to "error".
This is CVE-2022-23036 / part of XSA-396.
Reported-by: Demi Marie Obenour <[email protected]>
Signed-off-by: Juergen Gross <[email protected]>
Reviewed-by: Roger Pau Monné <[email protected]>
---
V2:
- use gnttab_try_end_foreign_access()
V4:
- use alloc_pages_exact() and free_pages_exact()
- set state to error if backend didn't unmap (Roger Pau Monné)
|
|
Add a new grant table function gnttab_try_end_foreign_access(), which
will remove and free a grant if it is not in use.
Its main use case is to either free a grant if it is no longer in use,
or to take some other action if it is still in use. This other action
can be an error exit, or (e.g. in the case of blkfront persistent grant
feature) some special handling.
This is CVE-2022-23036, CVE-2022-23038 / part of XSA-396.
Reported-by: Demi Marie Obenour <[email protected]>
Signed-off-by: Juergen Gross <[email protected]>
Reviewed-by: Jan Beulich <[email protected]>
---
V2:
- new patch
V4:
- add comments to header (Jan Beulich)
|
|
Letting xenbus_grant_ring() tear down grants in the error case is
problematic, as the other side could already have used these grants.
Calling gnttab_end_foreign_access_ref() without checking success is
resulting in an unclear situation for any caller of xenbus_grant_ring()
as in the error case the memory pages of the ring page might be
partially mapped. Freeing them would risk unwanted foreign access to
them, while not freeing them would leak memory.
In order to remove the need to undo any gnttab_grant_foreign_access()
calls, use gnttab_alloc_grant_references() to make sure no further
error can occur in the loop granting access to the ring pages.
It should be noted that this way of handling removes leaking of
grant entries in the error case, too.
This is CVE-2022-23040 / part of XSA-396.
Reported-by: Demi Marie Obenour <[email protected]>
Signed-off-by: Juergen Gross <[email protected]>
Reviewed-by: Jan Beulich <[email protected]>
|
|
In vhost_update_avail_event() we never used the `avail_event` argument,
since its introduction in commit 2723feaa8ec6 ("vhost: set log when
updating used flags or avail event").
Let's remove it to clean up the code.
Signed-off-by: Stefano Garzarella <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Michael S. Tsirkin <[email protected]>
|
|
There's no special reason why virtio-mem needs a default that's
different from what kconfig provides, any more than e.g. virtio blk.
Signed-off-by: Michael S. Tsirkin <[email protected]>
Acked-by: David Hildenbrand <[email protected]>
|
|
When vp_vdpa driver is unbind, vp_vdpa is freed in vdpa_unregister_device
and then vp_vdpa->mdev.pci_dev is dereferenced in vp_modern_remove,
triggering use-after-free.
Call Trace of unbinding driver free vp_vdpa :
do_syscall_64
vfs_write
kernfs_fop_write_iter
device_release_driver_internal
pci_device_remove
vp_vdpa_remove
vdpa_unregister_device
kobject_release
device_release
kfree
Call Trace of dereference vp_vdpa->mdev.pci_dev:
vp_modern_remove
pci_release_selected_regions
pci_release_region
pci_resource_len
pci_resource_end
(dev)->resource[(bar)].end
Signed-off-by: Zhang Min <[email protected]>
Signed-off-by: Yi Wang <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Michael S. Tsirkin <[email protected]>
Fixes: 64b9f64f80a6 ("vdpa: introduce virtio pci driver")
Reviewed-by: Stefano Garzarella <[email protected]>
|
|
Currently we have a BUG_ON() to make sure the number of sg
list does not exceed queue_max_segments() in virtio_queue_rq().
However, the block layer uses queue_max_discard_segments()
instead of queue_max_segments() to limit the sg list for
discard requests. So the BUG_ON() might be triggered if
virtio-blk device reports a larger value for max discard
segment than queue_max_segments(). To fix it, let's simply
remove the BUG_ON() which has become unnecessary after commit
02746e26c39e("virtio-blk: avoid preallocating big SGL for data").
And the unused vblk->sg_elems can also be removed together.
Fixes: 1f23816b8eb8 ("virtio_blk: add discard and write zeroes support")
Suggested-by: Christoph Hellwig <[email protected]>
Signed-off-by: Xie Yongji <[email protected]>
Reviewed-by: Max Gurtovoy <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Michael S. Tsirkin <[email protected]>
|
|
Currently the value of max_discard_segment will be set to
MAX_DISCARD_SEGMENTS (256) with no basis in hardware if device
set 0 to max_discard_seg in configuration space. It's incorrect
since the device might not be able to handle such large descriptors.
To fix it, let's follow max_segments restrictions in this case.
Fixes: 1f23816b8eb8 ("virtio_blk: add discard and write zeroes support")
Signed-off-by: Xie Yongji <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Michael S. Tsirkin <[email protected]>
|
|
In vhost_iotlb_add_range_ctx(), range size can overflow to 0 when
start is 0 and last is ULONG_MAX. One instance where it can happen
is when userspace sends an IOTLB message with iova=size=uaddr=0
(vhost_process_iotlb_msg). So, an entry with size = 0, start = 0,
last = ULONG_MAX ends up in the iotlb. Next time a packet is sent,
iotlb_access_ok() loops indefinitely due to that erroneous entry.
Call Trace:
<TASK>
iotlb_access_ok+0x21b/0x3e0 drivers/vhost/vhost.c:1340
vq_meta_prefetch+0xbc/0x280 drivers/vhost/vhost.c:1366
vhost_transport_do_send_pkt+0xe0/0xfd0 drivers/vhost/vsock.c:104
vhost_worker+0x23d/0x3d0 drivers/vhost/vhost.c:372
kthread+0x2e9/0x3a0 kernel/kthread.c:377
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:295
</TASK>
Reported by syzbot at:
https://syzkaller.appspot.com/bug?extid=0abd373e2e50d704db87
To fix this, do two things:
1. Return -EINVAL in vhost_chr_write_iter() when userspace asks to map
a range with size 0.
2. Fix vhost_iotlb_add_range_ctx() to handle the range [0, ULONG_MAX]
by splitting it into two entries.
Fixes: 0bbe30668d89e ("vhost: factor out IOTLB")
Reported-by: [email protected]
Tested-by: [email protected]
Signed-off-by: Anirudh Rayabharam <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Michael S. Tsirkin <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
- a fixup for Goodix touchscreen driver allowing it to work on certain
Cherry Trail devices
- a fix for imbalanced enable/disable regulator in Elam touchpad driver
that became apparent when used with Asus TF103C 2-in-1 dock
- a couple new input keycodes used on newer keyboards
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
HID: add mapping for KEY_ALL_APPLICATIONS
HID: add mapping for KEY_DICTATE
Input: elan_i2c - fix regulator enable count imbalance after suspend/resume
Input: elan_i2c - move regulator_[en|dis]able() out of elan_[en|dis]able_power()
Input: goodix - workaround Cherry Trail devices with a bogus ACPI Interrupt() resource
Input: goodix - use the new soc_intel_is_byt() helper
Input: samsung-keypad - properly state IOMEM dependency
|
|
dsp_pipeline_build() allocates dup pointer by kstrdup(cfg),
but then it updates dup variable by strsep(&dup, "|").
As a result when it calls kfree(dup), the dup variable contains NULL.
Found by Linux Driver Verification project (linuxtesting.org) with SVACE.
Signed-off-by: Alexey Khoroshilov <[email protected]>
Fixes: 960366cf8dbb ("Add mISDN DSP")
Signed-off-by: David S. Miller <[email protected]>
|
|
This PHY doesn't support a link-up interrupt source. If aneg is enabled
we use the "aneg complete" interrupt for this purpose, but if aneg is
disabled link-up isn't signaled currently.
According to a vendor driver there's an additional "energy detect"
interrupt source that can be used to signal link-up if aneg is disabled.
We can safely ignore this interrupt source if aneg is enabled.
This patch was tested on a TX3 Mini TV box with S905W (even though
boot message says it's a S905D).
This issue has been existing longer, but due to changes in phylib and
the driver the patch applies only from the commit marked as fixed.
Fixes: 84c8f773d2dc ("net: phy: meson-gxl: remove the use of .ack_callback()")
Signed-off-by: Heiner Kallweit <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu fixes from Joerg Roedel:
- Fix a double list_add() in Intel VT-d code
- Add missing put_device() in Tegra SMMU driver
- Two AMD IOMMU fixes:
- Memory leak in IO page-table freeing code
- Add missing recovery from event-log overflow
* tag 'iommu-fixes-v5.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/tegra-smmu: Fix missing put_device() call in tegra_smmu_find
iommu/vt-d: Fix double list_add when enabling VMD in scalable mode
iommu/amd: Fix I/O page table memory leak
iommu/amd: Recover from event log overflow
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull thermal control fix from Rafael Wysocki:
"Fix NULL pointer dereference in the thermal netlink interface (Nicolas
Cavallari)"
* tag 'thermal-5.17-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
thermal: core: Fix TZ_GET_TRIP NULL pointer dereference
|
|
Pull drm fixes from Dave Airlie:
"Things are quieting down as expected, just a small set of fixes, i915,
exynos, amdgpu, vrr, bridge and hdlcd. Nothing scary at all.
i915:
- Fix GuC SLPC unset command
- Fix misidentification of some Apple MacBook Pro laptops as Jasper Lake
amdgpu:
- Suspend regression fix
exynos:
- irq handling fixes
- Fix two regressions to TE-gpio handling
arm/hdlcd:
- Select DRM_GEM_CMEA_HELPER for HDLCD
bridge:
- ti-sn65dsi86: Properly undo autosuspend
vrr:
- Fix potential NULL-pointer deref"
* tag 'drm-fixes-2022-03-04' of git://anongit.freedesktop.org/drm/drm:
drm/amdgpu: fix suspend/resume hang regression
drm/vrr: Set VRR capable prop only if it is attached to connector
drm/arm: arm hdlcd select DRM_GEM_CMA_HELPER
drm/bridge: ti-sn65dsi86: Properly undo autosuspend
drm/i915: s/JSP2/ICP2/ PCH
drm/i915/guc/slpc: Correct the param count for unset param
drm/exynos: Search for TE-gpio in DSI panel's node
drm/exynos: Don't fail if no TE-gpio is defined for DSI driver
drm/exynos: gsc: Use platform_get_irq() to get the interrupt
drm/exynos/fimc: Use platform_get_irq() to get the interrupt
drm/exynos/exynos_drm_fimd: Use platform_get_irq_byname() to get the interrupt
drm/exynos: mixer: Use platform_get_irq() to get the interrupt
drm/exynos/exynos7_drm_decon: Use platform_get_irq_byname() to get the interrupt
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"These two fixes should fix the issues seen on the OrangePi, first we
needed the correct offset when calling pinctrl_gpio_direction(), and
fixing that made a lockdep issue explode in our face. Both now fixed"
* tag 'pinctrl-v5.17-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: sunxi: Use unique lockdep classes for IRQs
pinctrl-sunxi: sunxi_pinctrl_gpio_direction_in/output: use correct offset
|
|
This fixes the following smatch warnings:
drivers/vdpa/vdpa_user/iova_domain.c:305 vduse_domain_alloc_iova() warn: should 'iova_pfn << shift' be a 64 bit type?
Fixes: 8c773d53fb7b ("vduse: Implement an MMU-based software IOTLB")
Reported-by: kernel test robot <[email protected]>
Reported-by: Dan Carpenter <[email protected]>
Signed-off-by: Xie Yongji <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Michael S. Tsirkin <[email protected]>
Acked-by: Jason Wang <[email protected]>
|
|
When control vq receives a VIRTIO_NET_CTRL_MQ_VQ_PAIRS_SET command
request from the driver, presently there is no validation against the
number of queue pairs to configure, or even if multiqueue had been
negotiated or not is unverified. This may lead to kernel panic due to
uninitialized resource for the queues were there any bogus request
sent down by untrusted driver. Tie up the loose ends there.
Fixes: 52893733f2c5 ("vdpa/mlx5: Add multiqueue support")
Signed-off-by: Si-Wei Liu <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Michael S. Tsirkin <[email protected]>
Reviewed-by: Eli Cohen <[email protected]>
Acked-by: Jason Wang <[email protected]>
|
|
Per VIRTIO v1.1 specification, section 5.1.3.1 Feature bit requirements:
"VIRTIO_NET_F_MQ Requires VIRTIO_NET_F_CTRL_VQ".
There's assumption in the mlx5_vdpa multiqueue code that MQ must come
together with CTRL_VQ. However, there's nowhere in the upper layer to
guarantee this assumption would hold. Were there an untrusted driver
sending down MQ without CTRL_VQ, it would compromise various spots for
e.g. is_index_valid() and is_ctrl_vq_idx(). Although this doesn't end
up with immediate panic or security loophole as of today's code, the
chance for this to be taken advantage of due to future code change is
not zero.
Harden the crispy assumption by failing the set_driver_features() call
when seeing (MQ && !CTRL_VQ). For that end, verify_min_features() is
renamed to verify_driver_features() to reflect the fact that it now does
more than just validate the minimum features. verify_driver_features()
is now used to accommodate various checks against the driver features
for set_driver_features().
Signed-off-by: Si-Wei Liu <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Michael S. Tsirkin <[email protected]>
Reviewed-by: Eli Cohen <[email protected]>
Acked-by: Jason Wang <[email protected]>
|
|
No functional change introduced. vdpa bus driver such as virtio_vdpa
or vhost_vdpa is not supposed to take care of the locking for core
by its own. The locked API vdpa_set_features should suffice the
bus driver's need.
Signed-off-by: Si-Wei Liu <[email protected]>
Reviewed-by: Eli Cohen <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Michael S. Tsirkin <[email protected]>
Acked-by: Jason Wang <[email protected]>
|
|
A common pattern for device reset is currently:
vdev->config->reset(vdev);
.. cleanup ..
reset prevents new interrupts from arriving and waits for interrupt
handlers to finish.
However if - as is common - the handler queues a work request which is
flushed during the cleanup stage, we have code adding buffers / trying
to get buffers while device is reset. Not good.
This was reproduced by running
modprobe virtio_console
modprobe -r virtio_console
in a loop.
Fix this up by calling virtio_break_device + flush before reset.
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1786239
Signed-off-by: Michael S. Tsirkin <[email protected]>
|
|
Looks like most callers get driver/device removal wrong.
Document what's expected of callers.
Signed-off-by: Michael S. Tsirkin <[email protected]>
|
|
The feature negotiation was designed in a way that
makes it possible for devices to know which config
fields will be accessed by drivers.
This is broken since commit 404123c2db79 ("virtio: allow drivers to
validate features") with fallout in at least block and net. We have a
partial work-around in commit 2f9a174f918e ("virtio: write back
F_VERSION_1 before validate") which at least lets devices find out which
format should config space have, but this is a partial fix: guests
should not access config space without acknowledging features since
otherwise we'll never be able to change the config space format.
To fix, split finalize_features from virtio_finalize_features and
call finalize_features with all feature bits before validation,
and then - if validation changed any bits - once again after.
Since virtio_finalize_features no longer writes out features
rename it to virtio_features_ok - since that is what it does:
checks that features are ok with the device.
As a side effect, this also reduces the amount of hypervisor accesses -
we now only acknowledge features once unless we are clearing any
features when validating (which is uncommon).
IRC I think that this was more or less always the intent in the spec but
unfortunately the way the spec is worded does not say this explicitly, I
plan to address this at the spec level, too.
Acked-by: Jason Wang <[email protected]>
Cc: [email protected]
Fixes: 404123c2db79 ("virtio: allow drivers to validate features")
Fixes: 2f9a174f918e ("virtio: write back F_VERSION_1 before validate")
Cc: "Halil Pasic" <[email protected]>
Signed-off-by: Michael S. Tsirkin <[email protected]>
|
|
virtio_finalize_features is only used internally within virtio.
No reason to export it.
Signed-off-by: Michael S. Tsirkin <[email protected]>
Reviewed-by: Cornelia Huck <[email protected]>
Acked-by: Jason Wang <[email protected]>
|
|
There is an oddity in the way the RSR register flags propagate to the
ISR register (and the actual interrupt output) on this hardware: it
appears that RSR register bits only result in ISR being asserted if the
interrupt was actually enabled at the time, so enabling interrupts with
RSR bits already set doesn't trigger an interrupt to be raised. There
was already a partial fix for this race in the macb_poll function where
it checked for RSR bits being set and re-triggered NAPI receive.
However, there was a still a race window between checking RSR and
actually enabling interrupts, where a lost wakeup could happen. It's
necessary to check again after enabling interrupts to see if RSR was set
just prior to the interrupt being enabled, and re-trigger receive in that
case.
This issue was noticed in a point-to-point UDP request-response protocol
which periodically saw timeouts or abnormally high response times due to
received packets not being processed in a timely fashion. In many
applications, more packets arriving, including TCP retransmissions, would
cause the original packet to be processed, thus masking the issue.
Fixes: 02f7a34f34e3 ("net: macb: Re-enable RX interrupt only when RX is done")
Cc: [email protected]
Co-developed-by: Scott McNutt <[email protected]>
Signed-off-by: Scott McNutt <[email protected]>
Signed-off-by: Robert Hancock <[email protected]>
Tested-by: Claudiu Beznea <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
* drm/arm: Select DRM_GEM_CMEA_HELPER for HDLCD
* drm/bridge: ti-sn65dsi86: Properly undo autosuspend
* drm/vrr: Fix potential NULL-pointer deref
Signed-off-by: Dave Airlie <[email protected]>
From: Thomas Zimmermann <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/YiCTGZ8IVCw0ilKK@linux-uq9g
|
|
https://gitlab.freedesktop.org/agd5f/linux into drm-fixes
amd-drm-fixes-5.17-2022-03-02:
amdgpu:
- Suspend regression fix
Signed-off-by: Dave Airlie <[email protected]>
From: Alex Deucher <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
- Fix GuC SLPC unset command. (Vinay Belgaumkar)
- Fix misidentification of some Apple MacBook Pro laptops as Jasper Lake. (Ville Syrjälä)
Signed-off-by: Dave Airlie <[email protected]>
From: Tvrtko Ursulin <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/YiCXHiTyCE7TbopG@tursulin-mobl2
|
|
This patch adds a new key definition for KEY_ALL_APPLICATIONS
and aliases KEY_DASHBOARD to it.
It also maps the 0x0c/0x2a2 usage code to KEY_ALL_APPLICATIONS.
Signed-off-by: William Mahon <[email protected]>
Acked-by: Benjamin Tissoires <[email protected]>
Link: https://lore.kernel.org/r/20220303035618.1.I3a7746ad05d270161a18334ae06e3b6db1a1d339@changeid
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
Numerous keyboards are adding dictate keys which allows for text
messages to be dictated by a microphone.
This patch adds a new key definition KEY_DICTATE and maps 0x0c/0x0d8
usage code to this new keycode. Additionally hid-debug is adjusted to
recognize this new usage code as well.
Signed-off-by: William Mahon <[email protected]>
Acked-by: Benjamin Tissoires <[email protected]>
Link: https://lore.kernel.org/r/20220303021501.1.I5dbf50eb1a7a6734ee727bda4a8573358c6d3ec0@changeid
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from can, xfrm, wifi, bluetooth, and netfilter.
Lots of various size fixes, the length of the tag speaks for itself.
Most of the 5.17-relevant stuff comes from xfrm, wifi and bt trees
which had been lagging as you pointed out previously. But there's also
a larger than we'd like portion of fixes for bugs from previous
releases.
Three more fixes still under discussion, including and xfrm revert for
uAPI error.
Current release - regressions:
- iwlwifi: don't advertise TWT support, prevent FW crash
- xfrm: fix the if_id check in changelink
- xen/netfront: destroy queues before real_num_tx_queues is zeroed
- bluetooth: fix not checking MGMT cmd pending queue, make scanning
work again
Current release - new code bugs:
- mptcp: make SIOCOUTQ accurate for fallback socket
- bluetooth: access skb->len after null check
- bluetooth: hci_sync: fix not using conn_timeout
- smc: fix cleanup when register ULP fails
- dsa: restore error path of dsa_tree_change_tag_proto
- iwlwifi: fix build error for IWLMEI
- iwlwifi: mvm: propagate error from request_ownership to the user
Previous releases - regressions:
- xfrm: fix pMTU regression when reported pMTU is too small
- xfrm: fix TCP MSS calculation when pMTU is close to 1280
- bluetooth: fix bt_skb_sendmmsg not allocating partial chunks
- ipv6: ensure we call ipv6_mc_down() at most once, prevent leaks
- ipv6: prevent leaks in igmp6 when input queues get full
- fix up skbs delta_truesize in UDP GRO frag_list
- eth: e1000e: fix possible HW unit hang after an s0ix exit
- eth: e1000e: correct NVM checksum verification flow
- ptp: ocp: fix large time adjustments
Previous releases - always broken:
- tcp: make tcp_read_sock() more robust in presence of urgent data
- xfrm: distinguishing SAs and SPs by if_id in xfrm_migrate
- xfrm: fix xfrm_migrate issues when address family changes
- dcb: flush lingering app table entries for unregistered devices
- smc: fix unexpected SMC_CLC_DECL_ERR_REGRMB error
- mac80211: fix EAPoL rekey fail in 802.3 rx path
- mac80211: fix forwarded mesh frames AC & queue selection
- netfilter: nf_queue: fix socket access races and bugs
- batman-adv: fix ToCToU iflink problems and check the result belongs
to the expected net namespace
- can: gs_usb, etas_es58x: fix opened_channel_cnt's accounting
- can: rcar_canfd: register the CAN device when fully ready
- eth: igb, igc: phy: drop premature return leaking HW semaphore
- eth: ixgbe: xsk: change !netif_carrier_ok() handling in
ixgbe_xmit_zc(), prevent live lock when link goes down
- eth: stmmac: only enable DMA interrupts when ready
- eth: sparx5: move vlan checks before any changes are made
- eth: iavf: fix races around init, removal, resets and vlan ops
- ibmvnic: more reset flow fixes
Misc:
- eth: fix return value of __setup handlers"
* tag 'net-5.17-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (92 commits)
ipv6: fix skb drops in igmp6_event_query() and igmp6_event_report()
net: dsa: make dsa_tree_change_tag_proto actually unwind the tag proto change
ixgbe: xsk: change !netif_carrier_ok() handling in ixgbe_xmit_zc()
selftests: mlxsw: resource_scale: Fix return value
selftests: mlxsw: tc_police_scale: Make test more robust
net: dcb: disable softirqs in dcbnl_flush_dev()
bnx2: Fix an error message
sfc: extend the locking on mcdi->seqno
net/smc: fix unexpected SMC_CLC_DECL_ERR_REGRMB error cause by server
net/smc: fix unexpected SMC_CLC_DECL_ERR_REGRMB error generated by client
net: arcnet: com20020: Fix null-ptr-deref in com20020pci_probe()
tcp: make tcp_read_sock() more robust
bpf, sockmap: Do not ignore orig_len parameter
net: ipa: add an interconnect dependency
net: fix up skbs delta_truesize in UDP GRO frag_list
iwlwifi: mvm: return value for request_ownership
nl80211: Update bss channel on channel switch for P2P_CLIENT
iwlwifi: fix build error for IWLMEI
ptp: ocp: Add ptp_ocp_adjtime_coarse for large adjustments
batman-adv: Don't expect inter-netns unique iflink indices
...
|
|
Pull auxdisplay fixes from Miguel Ojeda:
"A few lcd2s fixes from Andy Shevchenko"
* tag 'auxdisplay-for-linus-v5.17-rc7' of git://github.com/ojeda/linux:
auxdisplay: lcd2s: Use proper API to free the instance of charlcd object
auxdisplay: lcd2s: Fix memory leak in ->remove()
auxdisplay: lcd2s: Fix lcd2s_redefine_char() feature
|