aboutsummaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)AuthorFilesLines
2021-10-11drm/msm/dpu: Fix address of SM8150 PINGPONG5 IRQ registerRobert Foss1-1/+1
Both PINGPONG4 and PINGPONG5 IRQ registers are using the same address, which is incorrect. PINGPONG4 should use the register offset 30, and PINGPONG5 should use the register offset 31 according to the downstream driver. Fixes: 667e9985ee24 ("drm/msm/dpu: replace IRQ lookup with the data in hw catalog") Signed-off-by: Robert Foss <[email protected]> Reviewed-by: Dmitry Baryshkov <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Dmitry Baryshkov <[email protected]> Signed-off-by: Rob Clark <[email protected]>
2021-10-11drm/msm: Do not run snapshot on non-DPU devicesFabio Estevam1-4/+5
Since commit 98659487b845 ("drm/msm: add support to take dpu snapshot") the following NULL pointer dereference is seen on i.MX53: [ 3.275493] msm msm: bound 30000000.gpu (ops a3xx_ops) [ 3.287174] [drm] Initialized msm 1.8.0 20130625 for msm on minor 0 [ 3.293915] 8<--- cut here --- [ 3.297012] Unable to handle kernel NULL pointer dereference at virtual address 00000028 [ 3.305244] pgd = (ptrval) [ 3.307989] [00000028] *pgd=00000000 [ 3.311624] Internal error: Oops: 805 [#1] SMP ARM [ 3.316430] Modules linked in: [ 3.319503] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.14.0+g682d702b426b #1 [ 3.326652] Hardware name: Freescale i.MX53 (Device Tree Support) [ 3.332754] PC is at __mutex_init+0x14/0x54 [ 3.336969] LR is at msm_disp_snapshot_init+0x24/0xa0 i.MX53 does not use the DPU controller. Fix the problem by only calling msm_disp_snapshot_init() on platforms that use the DPU controller. Cc: [email protected] Fixes: 98659487b845 ("drm/msm: add support to take dpu snapshot") Signed-off-by: Fabio Estevam <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Rob Clark <[email protected]>
2021-10-11drm/msm/a3xx: fix error handling in a3xx_gpu_init()Dan Carpenter1-4/+5
These error paths returned 1 on failure, instead of a negative error code. This would lead to an Oops in the caller. A second problem is that the check for "if (ret != -ENODATA)" did not work because "ret" was set to 1. Fixes: 5785dd7a8ef0 ("drm/msm: Fix duplicate gpu node in icc summary") Signed-off-by: Dan Carpenter <[email protected]> Link: https://lore.kernel.org/r/20211001125904.GK2283@kili Signed-off-by: Rob Clark <[email protected]>
2021-10-11drm/msm/a4xx: fix error handling in a4xx_gpu_init()Dan Carpenter1-4/+5
This code returns 1 on error instead of a negative error. It leads to an Oops in the caller. A second problem is that the check for "if (ret != -ENODATA)" cannot be true because "ret" is set to 1. Fixes: 5785dd7a8ef0 ("drm/msm: Fix duplicate gpu node in icc summary") Signed-off-by: Dan Carpenter <[email protected]> Link: https://lore.kernel.org/r/20211001125759.GJ2283@kili Signed-off-by: Rob Clark <[email protected]>
2021-10-11drm/msm: Fix null pointer dereference on pointer edpColin Ian King1-1/+2
The initialization of pointer dev dereferences pointer edp before edp is null checked, so there is a potential null pointer deference issue. Fix this by only dereferencing edp after edp has been null checked. Addresses-Coverity: ("Dereference before null check") Fixes: ab5b0107ccf3 ("drm/msm: Initial add eDP support in msm drm driver (v5)") Signed-off-by: Colin Ian King <[email protected]> Reviewed-by: Dmitry Baryshkov <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Rob Clark <[email protected]>
2021-10-11drm/msm/mdp5: fix cursor-related warningsDmitry Baryshkov1-0/+16
Since f35a2a99100f ("drm/encoder: make encoder control functions optional") drm_mode_config_validate would print warnings if both cursor plane and cursor functions are provided. Restore separate set of drm_crtc_funcs to be used if separate cursor plane is provided. [ 6.556046] ------------[ cut here ]------------ [ 6.556071] [CRTC:93:crtc-0] must not have both a cursor plane and a cursor_set func [ 6.556091] WARNING: CPU: 1 PID: 76 at drivers/gpu/drm/drm_mode_config.c:648 drm_mode_config_validate+0x238/0x4d0 [ 6.567453] Modules linked in: [ 6.577604] CPU: 1 PID: 76 Comm: kworker/u8:2 Not tainted 5.15.0-rc1-dirty #43 [ 6.580557] Hardware name: Qualcomm Technologies, Inc. DB820c (DT) [ 6.587763] Workqueue: events_unbound deferred_probe_work_func [ 6.593926] pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 6.599740] pc : drm_mode_config_validate+0x238/0x4d0 [ 6.606596] lr : drm_mode_config_validate+0x238/0x4d0 [ 6.611804] sp : ffff8000121b3980 [ 6.616838] x29: ffff8000121b3990 x28: 0000000000000000 x27: 0000000000000001 [ 6.620140] x26: ffff8000114cde50 x25: ffff8000114cdd40 x24: ffff0000987282d8 [ 6.627258] x23: 0000000000000000 x22: 0000000000000000 x21: 0000000000000001 [ 6.634376] x20: ffff000098728000 x19: ffff000080a39000 x18: ffffffffffffffff [ 6.641494] x17: 3136564e3631564e x16: 0000000000000324 x15: ffff800011c78709 [ 6.648613] x14: 0000000000000000 x13: ffff800011a22850 x12: 00000000000009ab [ 6.655730] x11: 0000000000000339 x10: ffff800011a22850 x9 : ffff800011a22850 [ 6.662848] x8 : 00000000ffffefff x7 : ffff800011a7a850 x6 : ffff800011a7a850 [ 6.669966] x5 : 000000000000bff4 x4 : 40000000fffff339 x3 : 0000000000000000 [ 6.677084] x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffff00008093b800 [ 6.684205] Call trace: [ 6.691319] drm_mode_config_validate+0x238/0x4d0 [ 6.693577] drm_dev_register+0x17c/0x210 [ 6.698435] msm_drm_bind+0x4b4/0x694 [ 6.702429] try_to_bring_up_master+0x164/0x1d0 [ 6.706075] __component_add+0xa0/0x170 [ 6.710415] component_add+0x14/0x20 [ 6.714234] msm_hdmi_dev_probe+0x1c/0x2c [ 6.718053] platform_probe+0x68/0xe0 [ 6.721959] really_probe.part.0+0x9c/0x30c [ 6.725606] __driver_probe_device+0x98/0x144 [ 6.729600] driver_probe_device+0xc8/0x15c [ 6.734114] __device_attach_driver+0xb4/0x120 [ 6.738106] bus_for_each_drv+0x78/0xd0 [ 6.742619] __device_attach+0xdc/0x184 [ 6.746351] device_initial_probe+0x14/0x20 [ 6.750172] bus_probe_device+0x9c/0xa4 [ 6.754337] deferred_probe_work_func+0x88/0xc0 [ 6.758158] process_one_work+0x1d0/0x370 [ 6.762671] worker_thread+0x2c8/0x470 [ 6.766839] kthread+0x15c/0x170 [ 6.770483] ret_from_fork+0x10/0x20 [ 6.773870] ---[ end trace 5884eb76cd26d274 ]--- [ 6.777500] ------------[ cut here ]------------ [ 6.782043] [CRTC:93:crtc-0] must not have both a cursor plane and a cursor_move func [ 6.782063] WARNING: CPU: 1 PID: 76 at drivers/gpu/drm/drm_mode_config.c:654 drm_mode_config_validate+0x290/0x4d0 [ 6.794362] Modules linked in: [ 6.804600] CPU: 1 PID: 76 Comm: kworker/u8:2 Tainted: G W 5.15.0-rc1-dirty #43 [ 6.807555] Hardware name: Qualcomm Technologies, Inc. DB820c (DT) [ 6.816148] Workqueue: events_unbound deferred_probe_work_func [ 6.822311] pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 6.828126] pc : drm_mode_config_validate+0x290/0x4d0 [ 6.834981] lr : drm_mode_config_validate+0x290/0x4d0 [ 6.840189] sp : ffff8000121b3980 [ 6.845223] x29: ffff8000121b3990 x28: 0000000000000000 x27: 0000000000000001 [ 6.848525] x26: ffff8000114cde50 x25: ffff8000114cdd40 x24: ffff0000987282d8 [ 6.855643] x23: 0000000000000000 x22: 0000000000000000 x21: 0000000000000001 [ 6.862763] x20: ffff000098728000 x19: ffff000080a39000 x18: ffffffffffffffff [ 6.869879] x17: 3136564e3631564e x16: 0000000000000324 x15: ffff800011c790c2 [ 6.876998] x14: 0000000000000000 x13: ffff800011a22850 x12: 0000000000000a2f [ 6.884116] x11: 0000000000000365 x10: ffff800011a22850 x9 : ffff800011a22850 [ 6.891234] x8 : 00000000ffffefff x7 : ffff800011a7a850 x6 : ffff800011a7a850 [ 6.898351] x5 : 000000000000bff4 x4 : 40000000fffff365 x3 : 0000000000000000 [ 6.905470] x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffff00008093b800 [ 6.912590] Call trace: [ 6.919702] drm_mode_config_validate+0x290/0x4d0 [ 6.921960] drm_dev_register+0x17c/0x210 [ 6.926821] msm_drm_bind+0x4b4/0x694 [ 6.930813] try_to_bring_up_master+0x164/0x1d0 [ 6.934459] __component_add+0xa0/0x170 [ 6.938799] component_add+0x14/0x20 [ 6.942619] msm_hdmi_dev_probe+0x1c/0x2c [ 6.946438] platform_probe+0x68/0xe0 [ 6.950345] really_probe.part.0+0x9c/0x30c [ 6.953991] __driver_probe_device+0x98/0x144 [ 6.957984] driver_probe_device+0xc8/0x15c [ 6.962498] __device_attach_driver+0xb4/0x120 [ 6.966492] bus_for_each_drv+0x78/0xd0 [ 6.971004] __device_attach+0xdc/0x184 [ 6.974737] device_initial_probe+0x14/0x20 [ 6.978556] bus_probe_device+0x9c/0xa4 [ 6.982722] deferred_probe_work_func+0x88/0xc0 [ 6.986543] process_one_work+0x1d0/0x370 [ 6.991057] worker_thread+0x2c8/0x470 [ 6.995223] kthread+0x15c/0x170 [ 6.998869] ret_from_fork+0x10/0x20 [ 7.002255] ---[ end trace 5884eb76cd26d275 ]--- Fixes: aa649e875daf ("drm/msm/mdp5: mdp5_crtc: Restore cursor state only if LM cursors are enabled") Signed-off-by: Dmitry Baryshkov <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Rob Clark <[email protected]>
2021-10-11drm/msm: Avoid potential overflow in timeout_to_jiffies()Marek Vasut1-2/+2
The return type of ktime_divns() is s64. The timeout_to_jiffies() currently assigns the result of this ktime_divns() to unsigned long, which on 32 bit systems may overflow. Furthermore, the result of this function is sometimes also passed to functions which expect signed long, dma_fence_wait_timeout() is one such example. Fix this by adjusting the type of remaining_jiffies to s64, so we do not suffer overflow there, and return a value limited to range of 0..INT_MAX, which is safe for all usecases of this timeout. The above overflow can be triggered if userspace passes in too large timeout value, larger than INT_MAX / HZ seconds. The kernel detects it and complains about "schedule_timeout: wrong timeout value %lx" and generates a warning backtrace. Note that this fixes commit 6cedb8b377bb ("drm/msm: avoid using 'timespec'"), because the previously used timespec_to_jiffies() function returned unsigned long instead of s64: static inline unsigned long timespec_to_jiffies(const struct timespec *value) Fixes: 6cedb8b377bb ("drm/msm: avoid using 'timespec'") Signed-off-by: Marek Vasut <[email protected]> Cc: Arnd Bergmann <[email protected]> Cc: Jordan Crouse <[email protected]> Cc: Rob Clark <[email protected]> Cc: [email protected] # 5.6+ Acked-by: Arnd Bergmann <[email protected]> Reviewed-by: Dmitry Baryshkov <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Rob Clark <[email protected]>
2021-10-11drm/msm: Fix devfreq NULL pointer dereference on a3xxStephan Gerhold1-0/+6
There is no devfreq on a3xx at the moment since gpu_busy is not implemented. This means that msm_devfreq_init() will return early and the entire devfreq setup is skipped. However, msm_devfreq_active() and msm_devfreq_idle() are still called unconditionally later, causing a NULL pointer dereference: Unable to handle kernel NULL pointer dereference at virtual address 0000000000000010 Internal error: Oops: 96000004 [#1] PREEMPT SMP CPU: 0 PID: 133 Comm: ring0 Not tainted 5.15.0-rc1 #4 Hardware name: Longcheer L8150 (DT) pc : mutex_lock_io+0x2bc/0x2f0 lr : msm_devfreq_active+0x3c/0xe0 [msm] Call trace: mutex_lock_io+0x2bc/0x2f0 msm_gpu_submit+0x164/0x180 [msm] msm_job_run+0x54/0xe0 [msm] drm_sched_main+0x2b0/0x4a0 [gpu_sched] kthread+0x154/0x160 ret_from_fork+0x10/0x20 Fix this by adding a check in msm_devfreq_active/idle() which ensures that devfreq was actually initialized earlier. Fixes: 9bc95570175a ("drm/msm: Devfreq tuning") Reported-by: Nikita Travkin <[email protected]> Tested-by: Nikita Travkin <[email protected]> Signed-off-by: Stephan Gerhold <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Rob Clark <[email protected]>
2021-10-11drm/msm/dp: only signal audio when disconnected detected at dp_pm_resumeKuogee Hsieh1-5/+5
Currently there is audio not working problem after system resume from suspend if hdmi monitor stay plugged in at DUT. However this problem does not happen at normal operation but at a particular test case. The root cause is DP driver signal audio with connected state at resume which trigger audio trying to setup audio data path through DP main link but failed due to display port is not setup and enabled by upper layer framework yet. This patch only have DP driver signal audio only when DP is in disconnected state so that audio option shows correct state after system resume. DP driver will not signal audio with connected state until display enabled executed by upper layer framework where display port is setup completed and main link is running. Changes in V2: -- add details commit text Fixes: afc9b8b6bab8 ("drm/msm/dp: signal audio plugged change at dp_pm_resume") Signed-off-by: Kuogee Hsieh <[email protected]> Reviewed-by: Stephen Boyd <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Rob Clark <[email protected]>
2021-10-11Merge tag 'linux-kselftest-kunit-fixes-5.15-rc6' of ↵Linus Torvalds3-1/+3
git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest Pull Kunit fixes from Shuah Khan: - Fixes to address the structleak plugin causing the stack frame size to grow immensely when used with KUnit. Fixes include adding a new makefile to disable structleak and using it from KUnit iio, device property, thunderbolt, and bitfield tests to disable it. - KUnit framework reference count leak in kfree_at_end - KUnit tool fix to resolve conflict between --json and --raw_output and generate correct test output in either case. - kernel-doc warnings due to mismatched arg names * tag 'linux-kselftest-kunit-fixes-5.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest: kunit: fix kernel-doc warnings due to mismatched arg names bitfield: build kunit tests without structleak plugin thunderbolt: build kunit tests without structleak plugin device property: build kunit tests without structleak plugin iio/test-format: build kunit tests without structleak plugin gcc-plugins/structleak: add makefile var for disabling structleak kunit: fix reference count leak in kfree_at_end kunit: tool: better handling of quasi-bool args (--json, --raw_output)
2021-10-12Revert "drm/mediatek: Use mailbox rx_callback instead of cmdq_task_cb"Chun-Kuang Hu1-13/+3
This reverts commit c1ec54b7b5af25c779192253f5a9f05e95cb43d7. Commit c1ec54b7b5af ("drm/mediatek: Use mailbox rx_callback instead of cmdq_task_cb") would cause numerous mtk cmdq mailbox driver warning: WARNING: CPU: 0 PID: 0 at drivers/mailbox/mtk-cmdq-mailbox.c:198 cmdq_task_exec_done+0xb8/0xe0 So revert that patch. Reported-by: Enric Balletbo Serra <[email protected]> Tested-by: Enric Balletbo Serra <[email protected]> Signed-off-by: Chun-Kuang Hu <[email protected]>
2021-10-12Revert "drm/mediatek: Remove struct cmdq_client"Chun-Kuang Hu1-62/+18
This reverts commit f4be17cd5b14dd73545b0e014a63ebe9ab5ef837. Commit c1ec54b7b5af ("drm/mediatek: Use mailbox rx_callback instead of cmdq_task_cb") would cause numerous mtk cmdq mailbox driver warning: WARNING: CPU: 0 PID: 0 at drivers/mailbox/mtk-cmdq-mailbox.c:198 cmdq_task_exec_done+0xb8/0xe0 So revert that patch and all the patches depend on that patch. Reported-by: Enric Balletbo Serra <[email protected]> Tested-by: Enric Balletbo Serra <[email protected]> Signed-off-by: Chun-Kuang Hu <[email protected]>
2021-10-12Revert "drm/mediatek: Detect CMDQ execution timeout"Chun-Kuang Hu1-12/+2
This reverts commit 8cdcb365342402fdeb664479b0a04e9debef8efb. Commit c1ec54b7b5af ("drm/mediatek: Use mailbox rx_callback instead of cmdq_task_cb") would cause numerous mtk cmdq mailbox driver warning: WARNING: CPU: 0 PID: 0 at drivers/mailbox/mtk-cmdq-mailbox.c:198 cmdq_task_exec_done+0xb8/0xe0 So revert that patch and all the patches depend on that patch. Reported-by: Enric Balletbo Serra <[email protected]> Tested-by: Enric Balletbo Serra <[email protected]> Signed-off-by: Chun-Kuang Hu <[email protected]>
2021-10-12Revert "drm/mediatek: Add cmdq_handle in mtk_crtc"Chun-Kuang Hu1-18/+10
This reverts commit bc9241be73d9b2b3bcb7033598521fd669639848. Commit c1ec54b7b5af ("drm/mediatek: Use mailbox rx_callback instead of cmdq_task_cb") would cause numerous mtk cmdq mailbox driver warning: WARNING: CPU: 0 PID: 0 at drivers/mailbox/mtk-cmdq-mailbox.c:198 cmdq_task_exec_done+0xb8/0xe0 So revert that patch and all the patches depend on that patch. Reported-by: Enric Balletbo Serra <[email protected]> Tested-by: Enric Balletbo Serra <[email protected]> Signed-off-by: Chun-Kuang Hu <[email protected]>
2021-10-12Revert "drm/mediatek: Clear pending flag when cmdq packet is done"Chun-Kuang Hu1-42/+5
This reverts commit 9efb16c2fdd647d3888fd8dae84509f485cd554e. Commit c1ec54b7b5af ("drm/mediatek: Use mailbox rx_callback instead of cmdq_task_cb") would cause numerous mtk cmdq mailbox driver warning: WARNING: CPU: 0 PID: 0 at drivers/mailbox/mtk-cmdq-mailbox.c:198 cmdq_task_exec_done+0xb8/0xe0 So revert that patch and all the patches depend on that patch. Reported-by: Enric Balletbo Serra <[email protected]> Tested-by: Enric Balletbo Serra <[email protected]> Signed-off-by: Chun-Kuang Hu <[email protected]>
2021-10-11drm/i915: remember to call i915_sw_fence_finiMatthew Auld1-0/+1
Seems to fix some object-debug splat which appeared while debugging something unrelated. v2: s/guc_blocked/guc_state.blocked/ Signed-off-by: Matthew Auld <[email protected]> Cc: Ville Syrjälä <[email protected]> Cc: Matthew Brost <[email protected]> Tested-by: Ville Syrjälä <[email protected]> Reviewed-by: Matthew Brost <[email protected]> Fixes: 62eaf0ae217d ("drm/i915/guc: Support request cancellation") Link: https://patchwork.freedesktop.org/patch/msgid/[email protected] (cherry picked from commit d576b31bdece7b5034047cbe21170e948198d32f) Signed-off-by: Jani Nikula <[email protected]>
2021-10-11platform/x86: int1092: Fix non sequential device mode handlingShravan S1-8/+15
SAR information from BIOS may come in non sequential pattern. To overcome the issue, a check is made to extract the right SAR information using the device mode which is currently being used. Remove .owner field if calls are used which set it automatically. Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci Signed-off-by: Shravan S <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Hans de Goede <[email protected]> Reviewed-by: Hans de Goede <[email protected]>
2021-10-11platform/x86: intel_skl_int3472: Correct null checkDaniel Scally1-1/+1
The int3472-discrete driver can enter an error path after initialising int3472->clock.ena_gpio, but before it has registered the clock. This will cause a NULL pointer dereference, because clkdev_drop() is not null aware. Instead of guarding the call to skl_int3472_unregister_clock() by checking for .ena_gpio, check specifically for the presence of the clk_lookup, which will guarantee clkdev_create() has already been called. Bug: https://bugzilla.kernel.org/show_bug.cgi?id=214453 Fixes: 7540599a5ef1 ("platform/x86: intel_skl_int3472: Provide skl_int3472_unregister_clock()") Signed-off-by: Daniel Scally <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Hans de Goede <[email protected]>
2021-10-11platform/x86: gigabyte-wmi: add support for B550 AORUS ELITE AX V2Zephaniah E. Loss-Cutler-Hull1-0/+1
This works just fine on my system. Signed-off-by: Zephaniah E. Loss-Cutler-Hull <[email protected]> Cc: <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Hans de Goede <[email protected]>
2021-10-11platform/x86: amd-pmc: Add alternative acpi id for PMC controllerSachi King1-0/+1
The Surface Laptop 4 AMD has used the AMD0005 to identify this controller instead of using the appropriate ACPI ID AMDI0005. Include AMD0005 in the acpi id list. Link: https://github.com/linux-surface/acpidumps/tree/master/surface_laptop_4_amd Link: https://gist.github.com/nakato/2a1a7df1a45fe680d7a08c583e1bf863 Cc: <[email protected]> # 5.14+ Signed-off-by: Sachi King <[email protected]> Reviewed-by: Mario Limonciello <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Hans de Goede <[email protected]>
2021-10-11platform/x86: intel_scu_ipc: Update timeout value in commentPrashant Malani1-1/+1
The comment decribing the IPC timeout hadn't been updated when the actual timeout was changed from 3 to 5 seconds in commit a7d53dbbc70a ("platform/x86: intel_scu_ipc: Increase virtual timeout from 3 to 5 seconds") . Since the value is anyway updated to 10s now, take this opportunity to update the value in the comment too. Signed-off-by: Prashant Malani <[email protected]> Cc: Benson Leung <[email protected]> Reviewed-by: Mika Westerberg <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Hans de Goede <[email protected]>
2021-10-11platform/x86: intel_scu_ipc: Increase virtual timeout to 10sPrashant Malani1-1/+1
Commit a7d53dbbc70a ("platform/x86: intel_scu_ipc: Increase virtual timeout from 3 to 5 seconds") states that the recommended timeout range is 5-10 seconds. Adjust the timeout value to the higher of those i.e 10 seconds, to account for situations where the 5 seconds is insufficient for disconnect command success. Signed-off-by: Prashant Malani <[email protected]> Cc: Benson Leung <[email protected]> Reviewed-by: Mika Westerberg <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Hans de Goede <[email protected]>
2021-10-11platform/x86: intel_scu_ipc: Fix busy loop expiry timePrashant Malani1-1/+1
The macro IPC_TIMEOUT is already in jiffies (it is also used like that elsewhere in the file when calling wait_for_completion_timeout()). Don’t convert it using helper functions for the purposes of calculating the busy loop expiry time. Fixes: e7b7ab3847c9 (“platform/x86: intel_scu_ipc: Sleeping is fine when polling”) Signed-off-by: Prashant Malani <[email protected]> Cc: Benson Leung <[email protected]> Reviewed-by: Mika Westerberg <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Hans de Goede <[email protected]>
2021-10-11platform/x86: dell: Make DELL_WMI_PRIVACY depend on DELL_WMIHans de Goede1-0/+1
DELL_WMI_PRIVACY is a feature toggle for the main dell-wmi driver, so it must depend on the Kconfig option which enables the main dell-wmi driver. Fixes: 8af9fa37b8a3 ("platform/x86: dell-privacy: Add support for Dell hardware privacy") Reported-by: Randy Dunlap <[email protected]> Signed-off-by: Hans de Goede <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2021-10-11platform/mellanox: mlxreg-io: Fix read access of n-bytes size attributesVadim Pasternak1-1/+1
Fix shift argument for function rol32(). It should be provided in bits, while was provided in bytes. Fixes: 86148190a7db ("platform/mellanox: mlxreg-io: Add support for complex attributes") Signed-off-by: Vadim Pasternak <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Hans de Goede <[email protected]>
2021-10-11platform/mellanox: mlxreg-io: Fix argument base in kstrtou32() callVadim Pasternak1-1/+1
Change kstrtou32() argument 'base' to be zero instead of 'len'. It works by chance for setting one bit value, but it is not supposed to work in case value passed to mlxreg_io_attr_store() is greater than 1. It works for example, for: echo 1 > /sys/devices/platform/mlxplat/mlxreg-io/hwmon/.../jtag_enable But it will fail for: echo n > /sys/devices/platform/mlxplat/mlxreg-io/hwmon/.../jtag_enable, where n > 1. The flow for input buffer conversion is as below: _kstrtoull(const char *s, unsigned int base, unsigned long long *res) calls: rv = _parse_integer(s, base, &_res); For the second case, where n > 1: - _parse_integer() converts 's' to 'val'. For n=2, 'len' is set to 2 (string buffer is 0x32 0x0a), for n=3 'len' is set to 3 (string buffer 0x33 0x0a), etcetera. - 'base' is equal or greater then '2' (length of input buffer). As a result, _parse_integer() exits with result zero (rv): rv = 0; while (1) { ... if (val >= base)-> (2 >= 2) break; ... rv++; ... } And _kstrtoull() in their turn will fail: if (rv == 0) return -EINVAL; Fixes: 5ec4a8ace06c ("platform/mellanox: Introduce support for Mellanox register access driver") Signed-off-by: Vadim Pasternak <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Hans de Goede <[email protected]>
2021-10-09Merge branch 'i2c/for-current-fixed' of ↵Linus Torvalds3-3/+13
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux Pull i2c fixes from Wolfram Sang: "Three driver bugfixes and one leak fix for the core" * 'i2c/for-current-fixed' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: i2c: mlxcpld: Modify register setting for 400KHz frequency i2c: mlxcpld: Fix criteria for frequency setting i2c: mediatek: Add OFFSET_EXT_CONF setting back i2c: acpi: fix resource leak in reconfiguration device addition
2021-10-09Merge tag 'scsi-fixes' of ↵Linus Torvalds6-43/+41
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi Pull SCSI fixes from James Bottomley: "Five fixes, all in drivers. The big change is the UFS task management rework, with lpfc next and the rest being fairly minor and obvious fixes" * tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: scsi: iscsi: Fix iscsi_task use after free scsi: lpfc: Fix memory overwrite during FC-GS I/O abort handling scsi: elx: efct: Delete stray unlock statement scsi: ufs: core: Fix task management completion scsi: acornscsi: Remove scsi_cmd_to_tag() reference
2021-10-09virtio-net: fix for skb_over_panic inside big modeXuan Zhuo1-1/+1
commit 126285651b7f ("Merge ra.kernel.org:/pub/scm/linux/kernel/git/netdev/net") accidentally reverted the effect of commit 1a8024239da ("virtio-net: fix for skb_over_panic inside big mode") on drivers/net/virtio_net.c As a result, users of crosvm (which is using large packet mode) are experiencing crashes with 5.14-rc1 and above that do not occur with 5.13. Crash trace: [ 61.346677] skbuff: skb_over_panic: text:ffffffff881ae2c7 len:3762 put:3762 head:ffff8a5ec8c22000 data:ffff8a5ec8c22010 tail:0xec2 end:0xec0 dev:<NULL> [ 61.369192] kernel BUG at net/core/skbuff.c:111! [ 61.372840] invalid opcode: 0000 [#1] SMP PTI [ 61.374892] CPU: 5 PID: 0 Comm: swapper/5 Not tainted 5.14.0-rc1 linux-v5.14-rc1-for-mesa-ci.tar.bz2 #1 [ 61.376450] Hardware name: ChromiumOS crosvm, BIOS 0 .. [ 61.393635] Call Trace: [ 61.394127] <IRQ> [ 61.394488] skb_put.cold+0x10/0x10 [ 61.395095] page_to_skb+0xf7/0x410 [ 61.395689] receive_buf+0x81/0x1660 [ 61.396228] ? netif_receive_skb_list_internal+0x1ad/0x2b0 [ 61.397180] ? napi_gro_flush+0x97/0xe0 [ 61.397896] ? detach_buf_split+0x67/0x120 [ 61.398573] virtnet_poll+0x2cf/0x420 [ 61.399197] __napi_poll+0x25/0x150 [ 61.399764] net_rx_action+0x22f/0x280 [ 61.400394] __do_softirq+0xba/0x257 [ 61.401012] irq_exit_rcu+0x8e/0xb0 [ 61.401618] common_interrupt+0x7b/0xa0 [ 61.402270] </IRQ> See https://lore.kernel.org/r/5edaa2b7c2fe4abd0347b8454b2ac032b6694e2c.camel%40collabora.com for the report. Apply the original 1a8024239da ("virtio-net: fix for skb_over_panic inside big mode") again, the original logic still holds: In virtio-net's large packet mode, there is a hole in the space behind buf. hdr_padded_len - hdr_len We must take this into account when calculating tailroom. Cc: Greg KH <[email protected]> Fixes: fb32856b16ad ("virtio-net: page_to_skb() use build_skb when there's sufficient tailroom") Fixes: 126285651b7f ("Merge ra.kernel.org:/pub/scm/linux/kernel/git/netdev/net") Signed-off-by: Xuan Zhuo <[email protected]> Reported-by: Corentin Noël <[email protected]> Tested-by: Corentin Noël <[email protected]> Signed-off-by: Michael S. Tsirkin <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2021-10-09net: phy: Do not shutdown PHYs in READY stateFlorian Fainelli1-0/+3
In case a PHY device was probed thus in the PHY_READY state, but not configured and with no network device attached yet, we should not be trying to shut it down because it has been brought back into reset by phy_device_reset() towards the end of phy_probe() and anyway we have not configured the PHY yet. Fixes: e2f016cf7751 ("net: phy: add a shutdown procedure") Signed-off-by: Florian Fainelli <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2021-10-09qed: Fix missing error code in qed_slowpath_start()chongjiapeng1-0/+1
The error code is missing in this code scenario, add the error code '-EINVAL' to the return value 'rc'. Eliminate the follow smatch warning: drivers/net/ethernet/qlogic/qed/qed_main.c:1298 qed_slowpath_start() warn: missing error code 'rc'. Reported-by: Abaci Robot <[email protected]> Fixes: d51e4af5c209 ("qed: aRFS infrastructure support") Signed-off-by: chongjiapeng <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2021-10-09isdn: mISDN: Fix sleeping function called from invalid contextZheyu Ma1-1/+1
The driver can call card->isac.release() function from an atomic context. Fix this by calling this function after releasing the lock. The following log reveals it: [ 44.168226 ] BUG: sleeping function called from invalid context at kernel/workqueue.c:3018 [ 44.168941 ] in_atomic(): 1, irqs_disabled(): 1, non_block: 0, pid: 5475, name: modprobe [ 44.169574 ] INFO: lockdep is turned off. [ 44.169899 ] irq event stamp: 0 [ 44.170160 ] hardirqs last enabled at (0): [<0000000000000000>] 0x0 [ 44.170627 ] hardirqs last disabled at (0): [<ffffffff814209ed>] copy_process+0x132d/0x3e00 [ 44.171240 ] softirqs last enabled at (0): [<ffffffff81420a1a>] copy_process+0x135a/0x3e00 [ 44.171852 ] softirqs last disabled at (0): [<0000000000000000>] 0x0 [ 44.172318 ] Preemption disabled at: [ 44.172320 ] [<ffffffffa009b0a9>] nj_release+0x69/0x500 [netjet] [ 44.174441 ] Call Trace: [ 44.174630 ] dump_stack_lvl+0xa8/0xd1 [ 44.174912 ] dump_stack+0x15/0x17 [ 44.175166 ] ___might_sleep+0x3a2/0x510 [ 44.175459 ] ? nj_release+0x69/0x500 [netjet] [ 44.175791 ] __might_sleep+0x82/0xe0 [ 44.176063 ] ? start_flush_work+0x20/0x7b0 [ 44.176375 ] start_flush_work+0x33/0x7b0 [ 44.176672 ] ? trace_irq_enable_rcuidle+0x85/0x170 [ 44.177034 ] ? kasan_quarantine_put+0xaa/0x1f0 [ 44.177372 ] ? kasan_quarantine_put+0xaa/0x1f0 [ 44.177711 ] __flush_work+0x11a/0x1a0 [ 44.177991 ] ? flush_work+0x20/0x20 [ 44.178257 ] ? lock_release+0x13c/0x8f0 [ 44.178550 ] ? __kasan_check_write+0x14/0x20 [ 44.178872 ] ? do_raw_spin_lock+0x148/0x360 [ 44.179187 ] ? read_lock_is_recursive+0x20/0x20 [ 44.179530 ] ? __kasan_check_read+0x11/0x20 [ 44.179846 ] ? do_raw_spin_unlock+0x55/0x900 [ 44.180168 ] ? ____kasan_slab_free+0x116/0x140 [ 44.180505 ] ? _raw_spin_unlock_irqrestore+0x41/0x60 [ 44.180878 ] ? skb_queue_purge+0x1a3/0x1c0 [ 44.181189 ] ? kfree+0x13e/0x290 [ 44.181438 ] flush_work+0x17/0x20 [ 44.181695 ] mISDN_freedchannel+0xe8/0x100 [ 44.182006 ] isac_release+0x210/0x260 [mISDNipac] [ 44.182366 ] nj_release+0xf6/0x500 [netjet] [ 44.182685 ] nj_remove+0x48/0x70 [netjet] [ 44.182989 ] pci_device_remove+0xa9/0x250 Signed-off-by: Zheyu Ma <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2021-10-09ionic: don't remove netdev->dev_addr when syncing uc listShannon Nelson1-0/+4
Bridging, and possibly other upper stack gizmos, adds the lower device's netdev->dev_addr to its own uc list, and then requests it be deleted when the upper bridge device is removed. This delete request also happens with the bridging vlan_filtering is enabled and then disabled. Bonding has a similar behavior with the uc list, but since it also uses set_mac to manage netdev->dev_addr, it doesn't have the same the failure case. Because we store our netdev->dev_addr in our uc list, we need to ignore the delete request from dev_uc_sync so as to not lose the address and all hope of communicating. Note that ndo_set_mac_address is expressly changing netdev->dev_addr, so no limitation is set there. Fixes: 2a654540be10 ("ionic: Add Rx filter and rx_mode ndo support") Signed-off-by: Shannon Nelson <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2021-10-08net: mana: Fix error handling in mana_create_rxq()Haiyang Zhang1-1/+3
Fix error handling in mana_create_rxq() when cq->gdma_id >= gc->max_num_cqs. Fixes: ca9c54d2d6a5 ("net: mana: Add a driver for Microsoft Azure Network Adapter (MANA)") Signed-off-by: Haiyang Zhang <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2021-10-08isdn: cpai: check ctr->cnr to avoid array index out of boundXiaolong Huang1-0/+5
The cmtp_add_connection() would add a cmtp session to a controller and run a kernel thread to process cmtp. __module_get(THIS_MODULE); session->task = kthread_run(cmtp_session, session, "kcmtpd_ctr_%d", session->num); During this process, the kernel thread would call detach_capi_ctr() to detach a register controller. if the controller was not attached yet, detach_capi_ctr() would trigger an array-index-out-bounds bug. [ 46.866069][ T6479] UBSAN: array-index-out-of-bounds in drivers/isdn/capi/kcapi.c:483:21 [ 46.867196][ T6479] index -1 is out of range for type 'capi_ctr *[32]' [ 46.867982][ T6479] CPU: 1 PID: 6479 Comm: kcmtpd_ctr_0 Not tainted 5.15.0-rc2+ #8 [ 46.869002][ T6479] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-2 04/01/2014 [ 46.870107][ T6479] Call Trace: [ 46.870473][ T6479] dump_stack_lvl+0x57/0x7d [ 46.870974][ T6479] ubsan_epilogue+0x5/0x40 [ 46.871458][ T6479] __ubsan_handle_out_of_bounds.cold+0x43/0x48 [ 46.872135][ T6479] detach_capi_ctr+0x64/0xc0 [ 46.872639][ T6479] cmtp_session+0x5c8/0x5d0 [ 46.873131][ T6479] ? __init_waitqueue_head+0x60/0x60 [ 46.873712][ T6479] ? cmtp_add_msgpart+0x120/0x120 [ 46.874256][ T6479] kthread+0x147/0x170 [ 46.874709][ T6479] ? set_kthread_struct+0x40/0x40 [ 46.875248][ T6479] ret_from_fork+0x1f/0x30 [ 46.875773][ T6479] Signed-off-by: Xiaolong Huang <[email protected]> Acked-by: Arnd Bergmann <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2021-10-08Merge tag 's390-5.15-5' of ↵Linus Torvalds1-8/+1
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux Pull s390 fixes from Vasily Gorbik: - Fix potential memory leak on a error path in eBPF - Fix handling of zpci device on reserve * tag 's390-5.15-5' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: s390/pci: fix zpci_zdev_put() on reserve bpf, s390: Fix potential memory leak about jit_data
2021-10-08net: dsa: mv88e6xxx: isolate the ATU databases of standalone and bridged portsVladimir Oltean2-13/+57
Similar to commit 6087175b7991 ("net: dsa: mt7530: use independent VLAN learning on VLAN-unaware bridges"), software forwarding between an unoffloaded LAG port (a bonding interface with an unsupported policy) and a mv88e6xxx user port directly under a bridge is broken. We adopt the same strategy, which is to make the standalone ports not find any ATU entry learned on a bridge port. Theory: the mv88e6xxx ATU is looked up by FID and MAC address. There are as many FIDs as VIDs (4096). The FID is derived from the VID when possible (the VTU maps a VID to a FID), with a fallback to the port based default FID value when not (802.1Q Mode is disabled on the port, or the classified VID isn't present in the VTU). The mv88e6xxx driver makes the following use of FIDs and VIDs: - the port's DefaultVID (to which untagged & pvid-tagged packets get classified) is 0 and is absent from the VTU, so this kind of packets is processed in FID 0, the default FID assigned by mv88e6xxx_setup_port. - every time a bridge VLAN is created, mv88e6xxx_port_vlan_join() -> mv88e6xxx_atu_new() associates a FID with that VID which increases linearly starting from 1. Like this: bridge vlan add dev lan0 vid 100 # FID 1 bridge vlan add dev lan1 vid 100 # still FID 1 bridge vlan add dev lan2 vid 1024 # FID 2 The FID allocation made by the driver is sub-optimal for the following reasons: (a) A standalone port has a DefaultPVID of 0 and a default FID of 0 too. A VLAN-unaware bridged port has a DefaultPVID of 0 and a default FID of 0 too. The difference is that the bridged ports may learn ATU entries, while the standalone port has the requirement that it must not, and must not find them either. Standalone ports must not use the same FID as ports belonging to a bridge. All standalone ports can use the same FID, since the ATU will never have an entry in that FID. (b) Multiple VLAN-unaware bridges will all use a DefaultPVID of 0 and a default FID of 0 on all their ports. The FDBs will not be isolated between these bridges. Every VLAN-unaware bridge must use the same FID on all its ports, different from the FID of other bridge ports. (c) Each bridge VLAN uses a unique FID which is useful for Independent VLAN Learning, but the same VLAN ID on multiple VLAN-aware bridges will result in the same FID being used by mv88e6xxx_atu_new(). The correct behavior is for VLAN 1 in br0 to have a different FID compared to VLAN 1 in br1. This patch cannot fix all the above. Traditionally the DSA framework did not care about this, and the reality is that DSA core involvement is needed for the aforementioned issues to be solved. The only thing we can solve here is an issue which does not require API changes, and that is issue (a), aka use a different FID for standalone ports vs ports under VLAN-unaware bridges. The first step is deciding what VID and FID to use for standalone ports, and what VID and FID for bridged ports. The 0/0 pair for standalone ports is what they used up till now, let's keep using that. For bridged ports, there are 2 cases: - VLAN-aware ports will never end up using the port default FID, because packets will always be classified to a VID in the VTU or dropped otherwise. The FID is the one associated with the VID in the VTU. - On VLAN-unaware ports, we _could_ leave their DefaultVID (pvid) at zero (just as in the case of standalone ports), and just change the port's default FID from 0 to a different number (say 1). However, Tobias points out that there is one more requirement to cater to: cross-chip bridging. The Marvell DSA header does not carry the FID in it, only the VID. So once a packet crosses a DSA link, if it has a VID of zero it will get classified to the default FID of that cascade port. Relying on a port default FID for upstream cascade ports results in contradictions: a default FID of 0 breaks ATU isolation of bridged ports on the downstream switch, a default FID of 1 breaks standalone ports on the downstream switch. So not only must standalone ports have different FIDs compared to bridged ports, they must also have different DefaultVID values. IEEE 802.1Q defines two reserved VID values: 0 and 4095. So we simply choose 4095 as the DefaultVID of ports belonging to VLAN-unaware bridges, and VID 4095 maps to FID 1. For the xmit operation to look up the same ATU database, we need to put VID 4095 in DSA tags sent to ports belonging to VLAN-unaware bridges too. All shared ports are configured to map this VID to the bridging FID, because they are members of that VLAN in the VTU. Shared ports don't need to have 802.1QMode enabled in any way, they always parse the VID from the DSA header, they don't need to look at the 802.1Q header. We install VID 4095 to the VTU in mv88e6xxx_setup_port(), with the mention that mv88e6xxx_vtu_setup() which was located right below that call was flushing the VTU so those entries wouldn't be preserved. So we need to relocate the VTU flushing prior to the port initialization during ->setup(). Also note that this is why it is safe to assume that VID 4095 will get associated with FID 1: the user ports haven't been created, so there is no avenue for the user to create a bridge VLAN which could otherwise race with the creation of another FID which would otherwise use up the non-reserved FID value of 1. [ Currently mv88e6xxx_port_vlan_join() doesn't have the option of specifying a preferred FID, it always calls mv88e6xxx_atu_new(). ] mv88e6xxx_port_db_load_purge() is the function to access the ATU for FDB/MDB entries, and it used to determine the FID to use for VLAN-unaware FDB entries (VID=0) using mv88e6xxx_port_get_fid(). But the driver only called mv88e6xxx_port_set_fid() once, during probe, so no surprises, the port FID was always 0, the call to get_fid() was redundant. As much as I would have wanted to not touch that code, the logic is broken when we add a new FID which is not the port-based default. Now the port-based default FID only corresponds to standalone ports, and FDB/MDB entries belong to the bridging service. So while in the future, when the DSA API will support FDB isolation, we will have to figure out the FID based on the bridge number, for now there's a single bridging FID, so hardcode that. Lastly, the tagger needs to check, when it is transmitting a VLAN untagged skb, whether it is sending it towards a bridged or a standalone port. When we see it is bridged we assume the bridge is VLAN-unaware. Not because it cannot be VLAN-aware but: - if we are transmitting from a VLAN-aware bridge we are likely doing so using TX forwarding offload. That code path guarantees that skbs have a vlan hwaccel tag in them, so we would not enter the "else" branch of the "if (skb->protocol == htons(ETH_P_8021Q))" condition. - if we are transmitting on behalf of a VLAN-aware bridge but with no TX forwarding offload (no PVT support, out of space in the PVT, whatever), we would indeed be transmitting with VLAN 4095 instead of the bridge device's pvid. However we would be injecting a "From CPU" frame, and the switch won't learn from that - it only learns from "Forward" frames. So it is inconsequential for address learning. And VLAN 4095 is absolutely enough for the frame to exit the switch, since we never remove that VLAN from any port. Fixes: 57e661aae6a8 ("net: dsa: mv88e6xxx: Link aggregation support") Reported-by: Tobias Waldekranz <[email protected]> Signed-off-by: Vladimir Oltean <[email protected]> Signed-off-by: Jakub Kicinski <[email protected]>
2021-10-08net: dsa: mv88e6xxx: keep the pvid at 0 when VLAN-unawareVladimir Oltean4-6/+76
The VLAN support in mv88e6xxx has a loaded history. Commit 2ea7a679ca2a ("net: dsa: Don't add vlans when vlan filtering is disabled") noticed some issues with VLAN and decided the best way to deal with them was to make the DSA core ignore VLANs added by the bridge while VLAN awareness is turned off. Those issues were never explained, just presented as "at least one corner case". That approach had problems of its own, presented by commit 54a0ed0df496 ("net: dsa: provide an option for drivers to always receive bridge VLANs") for the DSA core, followed by commit 1fb74191988f ("net: dsa: mv88e6xxx: fix vlan setup") which applied ds->configure_vlan_while_not_filtering = true for mv88e6xxx in particular. We still don't know what corner case Andrew saw when he wrote commit 2ea7a679ca2a ("net: dsa: Don't add vlans when vlan filtering is disabled"), but Tobias now reports that when we use TX forwarding offload, pinging an external station from the bridge device is broken if the front-facing DSA user port has flooding turned off. The full description is in the link below, but for short, when a mv88e6xxx port is under a VLAN-unaware bridge, it inherits that bridge's pvid. So packets ingressing a user port will be classified to e.g. VID 1 (assuming that value for the bridge_default_pvid), whereas when tag_dsa.c xmits towards a user port, it always sends packets using a VID of 0 if that port is standalone or under a VLAN-unaware bridge - or at least it did so prior to commit d82f8ab0d874 ("net: dsa: tag_dsa: offload the bridge forwarding process"). In any case, when there is a conversation between the CPU and a station connected to a user port, the station's MAC address is learned in VID 1 but the CPU tries to transmit through VID 0. The packets reach the intended station, but via flooding and not by virtue of matching the existing ATU entry. DSA has established (and enforced in other drivers: sja1105, felix, mt7530) that a VLAN-unaware port should use a private pvid, and not inherit the one from the bridge. The bridge's pvid should only be inherited when that bridge is VLAN-aware, so all state transitions need to be handled. On the other hand, all bridge VLANs should sit in the VTU starting with the moment when the bridge offloads them via switchdev, they are just not used. This solves the problem that Tobias sees because packets ingressing on VLAN-unaware user ports now get classified to VID 0, which is also the VID used by tag_dsa.c on xmit. Fixes: d82f8ab0d874 ("net: dsa: tag_dsa: offload the bridge forwarding process") Link: https://patchwork.kernel.org/project/netdevbpf/patch/[email protected]/#24491503 Reported-by: Tobias Waldekranz <[email protected]> Signed-off-by: Vladimir Oltean <[email protected]> Signed-off-by: Jakub Kicinski <[email protected]>
2021-10-08Merge tag 'for-linus-5.15b-rc5-tag' of ↵Linus Torvalds4-25/+31
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip Pull xen fixes from Juergen Gross: - fix two minor issues in the Xen privcmd driver plus a cleanup patch for that driver - fix multiple issues related to running as PVH guest and some related earlyprintk fixes for other Xen guest types - fix an issue introduced in 5.15 the Xen balloon driver * tag 'for-linus-5.15b-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: xen/balloon: fix cancelled balloon action xen/x86: adjust data placement x86/PVH: adjust function/data placement xen/x86: hook up xen_banner() also for PVH xen/x86: generalize preferred console model from PV to PVH Dom0 xen/x86: make "earlyprintk=xen" work for HVM/PVH DomU xen/x86: allow "earlyprintk=xen" to work for PV Dom0 xen/x86: make "earlyprintk=xen" work better for PVH Dom0 xen/x86: allow PVH Dom0 without XEN_PV=y xen/x86: prevent PVH type from getting clobbered xen/privcmd: drop "pages" parameter from xen_remap_pfn() xen/privcmd: fix error handling in mmap-resource processing xen/privcmd: replace kcalloc() by kvcalloc() when allocating empty pages
2021-10-08Merge tag 'asm-generic-fixes-5.15' of ↵Linus Torvalds11-14/+16
git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic Pull asm-generic fixes from Arnd Bergmann: "There is one build fix for Arm platforms that ended up impacting most architectures because of the way the drivers/firmware Kconfig file is wired up: The CONFIG_QCOM_SCM dependency have caused a number of randconfig regressions over time, and some still remain in v5.15-rc4. The fix we agreed on in the end is to make this symbol selected by any driver using it, and then building it even for non-Arm platforms with CONFIG_COMPILE_TEST. To make this work on all architectures, the drivers/firmware/Kconfig file needs to be included for all architectures to make the symbol itself visible. In a separate discussion, we found that a sound driver patch that is pending for v5.16 needs the same change to include this Kconfig file, so the easiest solution seems to have my Kconfig rework included in v5.15. Finally, the branch also includes a small unrelated build fix for NOMMU architectures" Link: https://lore.kernel.org/all/[email protected]/ Link: https://lore.kernel.org/all/[email protected]/ Link: https://lore.kernel.org/all/[email protected]/ * tag 'asm-generic-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic: asm-generic/io.h: give stub iounmap() on !MMU same prototype as elsewhere qcom_scm: hide Kconfig symbol firmware: include drivers/firmware/Kconfig unconditionally
2021-10-08Merge tag 'acpi-5.15-rc5' of ↵Linus Torvalds1-0/+3
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm Pull ACPI fix from Rafael Wysocki: "Fix a recent ACPI-related regression in the PCI subsystem that introduced a NULL pointer dereference possible to trigger from user space via sysfs on some systems" * tag 'acpi-5.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: PCI: ACPI: Check parent pointer in acpi_pci_find_companion()
2021-10-08Merge tag 'usb-5.15-rc5' of ↵Linus Torvalds10-29/+42
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb Pull USB fixes from Greg KH: "Here are some small USB fixes for 5.15-rc5 that resolve a number of reported issues: - gadget driver fixes - xhci build warning fixes - build configuration fix - cdc-acm tty handling fixes - cdc-wdm fix - typec fixes All of these have been in linux-next for a while with no reported issues" * tag 'usb-5.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: USB: cdc-acm: fix break reporting USB: cdc-acm: fix racy tty buffer accesses usb: gadget: f_uac2: fixed EP-IN wMaxPacketSize usb: cdc-wdm: Fix check for WWAN usb: chipidea: ci_hdrc_imx: Also search for 'phys' phandle usb: typec: tcpm: handle SRC_STARTUP state if cc changes usb: typec: tcpci: don't handle vSafe0V event if it's not enabled usb: typec: tipd: Remove dependency on "connector" child fwnode Partially revert "usb: Kconfig: using select for USB_COMMON dependency" usb: dwc3: gadget: Revert "set gadgets parent to the right controller" usb: xhci: tegra: mark PM functions as __maybe_unused
2021-10-08Merge tag 'mmc-v5.15-rc4' of ↵Linus Torvalds2-25/+70
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc Pull MMC fixes from Ulf Hansson: "A couple of MMC host fixes: - meson-gx: Fix read/write access for dram-access-quirk - sdhci-of-at91: Fix calibration sequence" * tag 'mmc-v5.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: mmc: meson-gx: do not use memcpy_to/fromio for dram-access-quirk mmc: sdhci-of-at91: replace while loop with read_poll_timeout mmc: sdhci-of-at91: wait for calibration done before proceed
2021-10-08Merge tag 'drm-fixes-2021-10-08' of git://anongit.freedesktop.org/drm/drmLinus Torvalds50-151/+709
Pull drm fixes from Dave Airlie: "I've returned from my tropical island retreat, even managed to bring one of my kids on a dive with some turtles. Thanks to Daniel for doing last week's work. Otherwise this is the weekly fixes pull, it's a bit bigger because the vc4 reverts in your tree caused some problems with fixes in the drm-misc tree so it got left out last week, so this week has the misc fixes rebased without the vc4 pieces. Otherwise it's i915, amdgpu with the usual fixes and a scattering over other drivers. I expect things should calm down a bit more next week. core: - Kconfig fix for fb_simple vs simpledrm. i915: - Fix RKL HDMI audio - Fix runtime pm imbalance on i915_gem_shrink() error path - Fix Type-C port access before hw/sw state sync - Fix VBT backlight struct version/size check - Fix VT-d async flip on SKL/BXT with plane stretch workaround amdgpu: - DCN 3.1 DP alt mode fixes - S0ix gfxoff fix - Fix DRM_AMD_DC_SI dependencies - PCIe DPC handling fix - DCN 3.1 scaling fix - Documentation fix amdkfd: - Fix potential memory leak - IOMMUv2 init fixes vc4 (there were some hdmi fixes but things got reverted, sort it out later): - compiler fix nouveau: - Cursor fix - Fix ttm buffer moves for ampere gpu's by adding minimal acceleration support. - memory leak fixes rockchip: - crtc/clk fixup panel: - ili9341 Fix DT bindings indent - y030xx067a - yellow tint init seq fix gbefb: - Fix gbefb when built with COMPILE_TEST" * tag 'drm-fixes-2021-10-08' of git://anongit.freedesktop.org/drm/drm: (33 commits) drm/amd/display: Fix detection of 4 lane for DPALT drm/amd/display: Limit display scaling to up to 4k for DCN 3.1 drm/amd/display: Skip override for preferred link settings during link training drm/nouveau/debugfs: fix file release memory leak drm/nouveau/kms/nv50-: fix file release memory leak drm/nouveau: avoid a use-after-free when BO init fails DRM: delete DRM IRQ legacy midlayer docs video: fbdev: gbefb: Only instantiate device when built for IP32 fbdev: simplefb: fix Kconfig dependencies drm/panel: abt-y030xx067a: yellow tint fix dt-bindings: panel: ili9341: correct indentation drm/nouveau/fifo/ga102: initialise chid on return from channel creation drm/rockchip: Update crtc fixup to account for fractional clk change drm/nouveau/ga102-: support ttm buffer moves via copy engine drm/nouveau/kms/tu102-: delay enabling cursor until after assign_windows drm/sun4i: dw-hdmi: Fix HDMI PHY clock setup drm/vc4: hdmi: Remove unused struct drm/kmb: Enable alpha blended second plane drm/amdgpu: handle the case of pci_channel_io_frozen only in amdgpu_pci_resume drm/amdgpu: init iommu after amdkfd device init ...
2021-10-08net: stmmac: add support for dwmac 3.40aHerve Codina2-0/+9
dwmac 3.40a is an old ip version that can be found on SPEAr3xx soc. Signed-off-by: Herve Codina <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2021-10-08net: stmmac: fix get_hw_feature() on old hardwareHerve Codina4-9/+22
Some old IPs do not provide the hardware feature register. On these IPs, this register is read 0x00000000. In old driver version, this feature was handled but a regression came with the commit f10a6a3541b4 ("stmmac: rework get_hw_feature function"). Indeed, this commit removes the return value in dma->get_hw_feature(). This return value was used to indicate the validity of retrieved information and used later on in stmmac_hw_init() to override priv->plat data if this hardware feature were valid. This patch restores the return code in ->get_hw_feature() in order to indicate the hardware feature validity and override priv->plat data only if this hardware feature is valid. Fixes: f10a6a3541b4 ("stmmac: rework get_hw_feature function") Signed-off-by: Herve Codina <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2021-10-08Merge tag 'amd-drm-fixes-5.15-2021-10-06' of ↵Dave Airlie13-24/+140
https://gitlab.freedesktop.org/agd5f/linux into drm-fixes amd-drm-fixes-5.15-2021-10-06: amdgpu: - DCN 3.1 DP alt mode fixes - S0ix gfxoff fix - Fix DRM_AMD_DC_SI dependencies - PCIe DPC handling fix - DCN 3.1 scaling fix - Documentation fix amdkfd: - Fix potential memory leak - IOMMUv2 init fixes Signed-off-by: Dave Airlie <[email protected]> From: Alex Deucher <[email protected]> Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
2021-10-08Merge tag 'drm-misc-fixes-2021-10-06' of ↵Dave Airlie28-99/+503
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes Rebased drm-misc-fixes for v5.15-rc5: - Dropped vc4 patches. - Compiler fix for vc4. - Cursor fix for nouveau. - Fix ttm buffer moves for ampere gpu's by adding minimal acceleration support. - Small rockchip fixes. - Fix DT bindings indent for ili9341. - Fix y030xx067a init sequence to not get a yellow tint. - Kconfig fix for fb_simple vs simpledrm. - Assorted nouvaeu memory leaks. - Fix gbefb when built with COMPILE_TEST. Signed-off-by: Dave Airlie <[email protected]> From: Maarten Lankhorst <[email protected]> Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
2021-10-07Merge tag 'armsoc-fixes-5.15' of ↵Linus Torvalds9-100/+57
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc Pull ARM SoC fixes from Arnd Bergmann: "This is a larger than normal update for Arm SoC specific code, most of it in device trees, but also drivers and the omap and at91/sama7 platforms: - There are four new entries to the MAINTAINERS file: Sven Peter and Alyssa Rosenzweig for Apple M1, Romain Perier for Mstar/sigmastar, and Vignesh Raghavendra for TI K3 - Build fixes to address randconfig warnings in sharpsl, dove, omap1, and qcom platforms as well as the scmi and op-tee subsystems - Regression fixes for missing CONFIG_FB and other options for several defconfigs - Several bug fixes for the newly added Microchip SAMA7 platform, mostly regarding power management - Missing SMP barriers to protect accesses to SCMI virtio device - Regression fixes for TI OMAP, including a boot-time hang on am335x. - Lots of bug fixes for NXP i.MX, mostly addressing incorrect settings in devicetree files, and one revert for broken suspend. - Fixes for ARM Juno/Vexpress devicetree files, addressing a couple of schema warnings. - Regression fixes for qualcomm SoC specific drivers and devicetree files, reverting an mdt_loader change and at least pastially reverting some of the 5.15 DTS changes, plus some minor bugfixes" * tag 'armsoc-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (64 commits) MAINTAINERS: Add Sven Peter as ARM/APPLE MACHINE maintainer MAINTAINERS: Add Alyssa Rosenzweig as M1 reviewer firmware: arm_scmi: Add proper barriers to scmi virtio device firmware: arm_scmi: Simplify spinlocks in virtio transport ARM: dts: omap3430-sdp: Fix NAND device node bus: ti-sysc: Use CLKDM_NOAUTO for dra7 dcan1 for errata i893 ARM: sharpsl_param: work around -Wstringop-overread warning ARM: defconfig: gemini: Restore framebuffer ARM: dove: mark 'putc' as inline ARM: omap1: move omap15xx local bus handling to usb.c MAINTAINERS: Add Vignesh to TI K3 platform maintainership arm64: dts: imx8m*-venice-gw7902: fix M2_RST# gpio ARM: imx6: disable the GIC CPU interface before calling stby-poweroff sequence arm64: dts: ls1028a: fix eSDHC2 node arm64: dts: imx8mm-kontron-n801x-som: do not allow to switch off buck2 ARM: dts: at91: sama7g5ek: to not touch slew-rate for SDMMC pins ARM: dts: at91: sama7g5ek: use proper slew-rate settings for GMACs ARM: at91: pm: preload base address of controllers in tlb ARM: at91: pm: group constants and addresses loading ARM: dts: at91: sama7g5ek: add suspend voltage for ddr3l rail ...
2021-10-07Merge tag 'scmi-fixes-5.15' of ↵Arnd Bergmann2-14/+32
git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/fixes SCMI fixes for v5.15 A few fixes addressing: - Kconfig dependency between VIRTIO and ARM_SCMI_PROTOCOL - Link-time error with __exit annotation for virtio_scmi_exit - Unnecessary nested irqsave/irqrestore spinlocks in virtio transport - Missing SMP barriers to protect accesses to SCMI virtio device * tag 'scmi-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux: firmware: arm_scmi: Add proper barriers to scmi virtio device firmware: arm_scmi: Simplify spinlocks in virtio transport firmware: arm_scmi: Remove __exit annotation firmware: arm_scmi: Fix virtio transport Kconfig dependency Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Arnd Bergmann <[email protected]>
Powered by cgit, Gruvboxed by Blaster4385.