| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
In ssb_calc_clock_rate(), there is a potential issue where the value of
m1 could be zero due to initialization using clkfactor_f6_resolv(). This
situation raised concerns about the possibility of a division by zero
error.
We fixed it by following the suggestions provided by Larry Finger
<Larry.Finger@lwfinger.net> and Michael Büsch <m@bues.ch>. The fix
involves returning a value of 1 instead of 0 in clkfactor_f6_resolv().
This modification ensures the proper functioning of the code and
eliminates the risk of division by zero errors.
Signed-off-by: Rand Deeb <rand.sec96@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Michael Büsch <m@bues.ch>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230904232346.34991-1-rand.sec96@gmail.com
|
|
Secure firmware is protected by public/private key cryptography. To help
firmware self verify integrity, configure a heap address for these
data before downloading firmware.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230901073956.54203-9-pkshih@realtek.com
|
|
To support download more than one firmware, adjust flow to download
firmware by unit of firmware suit. Then, flow becomes
1. initial setup - disable/enable_wcpu
2. for all firmware suits
2.1. download WiFi CPU, and check ready
2.2. download BB MCU, and check ready
3. check status code to make sure all ready
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230901073956.54203-8-pkshih@realtek.com
|
|
firmware
Before downloading firmware for BB MCU, call this ops to enable baseband
hardware.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230901073956.54203-7-pkshih@realtek.com
|
|
Though WiFi 7 chips need BB MCU firmware, we don't download it in probe
stage. Instead, only bring interface up under normal operation or WoWLAN
mode. So, add an argument to assist download flow to setup download
settings properly.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230901073956.54203-6-pkshih@realtek.com
|
|
For WiFi 6 chips, there is only single one firmware i.e. WiFi CPU firmware,
so no need an argument to discriminate them. For WiFi 7 chips, BB MCU
firmware is introduced, and we need to check it ready after downloading.
For each type of firmware, we need to check corresponding hardware ready
bit. After downloading all firmware, check status code to determine if
all things are ready.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230901073956.54203-5-pkshih@realtek.com
|
|
7 chips
To work with generalized flow of download firmware, implement WiFi 7
specific functions to support it. These functions include disable/enable
WiFi CPU, status of path ready, and status of firmware.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230901073956.54203-4-pkshih@realtek.com
|
|
In order to reuse the flow to download firmware, define some mac_gen::ops
to implement them for WiFi 6 and 7 chips individually. This doesn't change
logic at all.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230901073956.54203-3-pkshih@realtek.com
|
|
individual function
To download firmware, we need to check path is ready. There are two kinds
of path -- one is to download firmware header, and the other is to download
firmware body.
Since the polling method is different from WiFi 7 chips, make it to be
an individual function, and then we can reuse the download flow.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230901073956.54203-2-pkshih@realtek.com
|
|
According to Wi-Fi/BT roles' settings, we fill corresponding H2Cs (host
to chip packets). Then, following MCC (multi-channel concurrency) pattern,
we send these H2Cs as planned. Eventually, the trigger H2Cs will be sent
to tell FW to really start/stop MCC.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230831053133.24015-7-pkshih@realtek.com
|
|
Fix a typo where `bitamp` should be `bitmap`. Don't change functionality
at all.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230831053133.24015-6-pkshih@realtek.com
|
|
After the previous works, we can now expand and display the MCC pattern
in more detail, as shown below.
|< MCC interval >|
|< duration ref >| (if mid bt) |< duration aux >| (if tail bt) |
|<tob ref >|< toa ref>| ... |<tob aux >|< toa aux>| ... |
V V
tbtt ref tbtt aux
|< beacon offset >|
(where tob means `time offset behind` and toa means `time offset ahead`)
There are two key points.
1. decide position of BT slot if MCC pattern needs to handle BT duration.
2. calculate all parameters related to tob and toa in MCC pattern.
For point (1), when BT duration needs to be handled, BT position will
rely on beacon offset, either middle or tail. For point (2), to ensure
durations of the Wi-Fi roles cover their beacons, we have to calculate
tob and toa for them according to their TBTT.
And, there are two strategies to calculate parameters, strict and loose.
In strict pattern, all parameters take HW time into account as limitation.
But, the strict calculation are not always successful. In loose pattern,
it only tries to give positive parameters to reference role and doesn't
care much about auxiliary role. If unfortunately auxiliary role gets
negative parameters in loose pattern, FW will be notified and then deal
with it. So, the loose calculation won't fail. In general, we always try
strict pattern cases before using a loose pattern.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230831053133.24015-5-pkshih@realtek.com
|
|
Before calculating MCC pattern, we have to determine whether to handle BT
duration in it or not. The decision will depend on the channels that Wi-Fi
roles use. And, we have three cases shown below.
1. non-2GHz + non-2GHz
2. non-2GHz + 2GHz (different band)
3. 2GHz + 2GHz (dual 2GHz)
For case (1), we don't care BT duration in MCC pattern. For case (2), we
still don't care BT duration in MCC pattern. Instead, we try to satisfy it
by modifying duration of Wi-Fi role on non-2GHz channel. For case (3), we
need to modify Wi-Fi durations and also need to handle BT duration in MCC
pattern.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230831053133.24015-4-pkshih@realtek.com
|
|
We determine the fundamental settings shown below.
|< MCC interval >|
|< duration ref >|< duration aux >|
| | | |
|< beacon offset >|
| |
V V
(tbtt ref) (tbtt aux)
(where `ref` (reference) and `aux` (auxiliary) mean the two MCC roles)
Based on MCC mode (GO+STA or GC+STA), we fill configurations of
MCC interval and beacon offset. And, we make sure each MCC role
have a basically required duration in the MCC interval.
The beacon offset mentioned above is a parameter for further MCC
pattern calculation. If MCC is in GC+STA mode, we will calculate
the real beacon offset through TSFs shown in beacons of both MCC
roles. Otherwise, we will use a default beacon offset, and make
GO sync STA's TSF timer with this offset.
MCC pattern calculation will break down each MCC role's duration
in more detail. We will implement it in the following.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230831053133.24015-3-pkshih@realtek.com
|
|
We prepare to support TDMA-based MCC (multi-channel concurrency)
which allows two kinds of modes below.
* P2P GO + normal STA
* P2P GC + normal STA
Each mode has two vif and two chanctx. Then, each vif binds one
separate chanctx and becomes one MCC role. We name the two MCC
roles as follows.
* MCC role - reference (ref)
We calculate the baseline of our TDMA things accodring
to its info, e.g. TBTT. In normal case, it will be put
at the first slot of TDMA.
* MCC role - auxiliary (aux)
MCC state machine will be running in FW eventually, but before that,
we have to fill and calculate things that are needed by FW. We fill
the information of MCC role according to its vif and its chanctx.
Then, we calculate the start time for MCC.
Note that the parameters used in the calculation now is assigned by
default rules. The precise parameters for better MCC behavior will be
derived in the following.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230831053133.24015-2-pkshih@realtek.com
|
|
Modify TSSI ADC FIFO Clock follow RX ADC Clock can avoid
transmit power inaccuracy.
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230830092849.153251-3-pkshih@realtek.com
|
|
TSSI configures bandedge to TX proper waveform, these new bandedge
parameters improve the accuracy of transmit power compensation.
This helps to avoid throughput degradation.
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230830092849.153251-2-pkshih@realtek.com
|
|
When compiling with clang 16.0.6 and CONFIG_FORTIFY_SOURCE=y, I've
noticed the following (somewhat confusing due to absence of an actual
source code location):
In file included from drivers/net/wireless/purelifi/plfxlc/mac.c:6:
In file included from ./include/linux/netdevice.h:24:
In file included from ./include/linux/timer.h:6:
In file included from ./include/linux/ktime.h:24:
In file included from ./include/linux/time.h:60:
In file included from ./include/linux/time32.h:13:
In file included from ./include/linux/timex.h:67:
In file included from ./arch/x86/include/asm/timex.h:5:
In file included from ./arch/x86/include/asm/processor.h:23:
In file included from ./arch/x86/include/asm/msr.h:11:
In file included from ./arch/x86/include/asm/cpumask.h:5:
In file included from ./include/linux/cpumask.h:12:
In file included from ./include/linux/bitmap.h:11:
In file included from ./include/linux/string.h:254:
./include/linux/fortify-string.h:592:4: warning: call to '__read_overflow2_field'
declared with 'warning' attribute: detected read beyond size of field (2nd
parameter); maybe use struct_group()? [-Wattribute-warning]
__read_overflow2_field(q_size_field, size);
The compiler actually complains on 'plfxlc_get_et_strings()' where
fortification logic inteprets call to 'memcpy()' as an attempt to copy
the whole 'et_strings' array from its first member and so issues an
overread warning. This warning may be silenced by passing an address
of the whole array and not the first member to 'memcpy()'.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230829094541.234751-1-dmantipov@yandex.ru
|
|
TOTOLINK N150UA V5/N150UA-B (VID=0x0bda, PID=0x2005) works fine with
the rtl8xxxu driver, so mark as tested.
Signed-off-by: Zenm Chen <zenmchen@gmail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230829074358.14795-1-zenmchen@gmail.com
|
|
The probe function of 8822cu is misplaced to 8822bu, so we fix it. Just
cosmetics, no changes in functionality.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230825062404.50813-1-pkshih@realtek.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-08-24 (igc, e1000e)
This series contains updates to igc and e1000e drivers.
Vinicius adds support for utilizing multiple PTP registers on igc.
Sasha reduces interval time for PTM on igc and adds new device support
on e1000e.
* '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
e1000e: Add support for the next LOM generation
igc: Decrease PTM short interval from 10 us to 1 us
igc: Add support for multiple in-flight TX timestamps
====================
Link: https://lore.kernel.org/r/20230824204418.1551093-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Rather than detecting when half-duplex is not supported, and clearing
the MAC capabilities, reverse the if() condition and use it to set the
capabilities instead.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qZAXn-005pUb-SP@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move priv->phylink_config.mac_managed_pm to be along side the other
phylink initialisations.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qZAXi-005pUV-Nq@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move the xgmac specific phylink capabilities to the dwxgmac2 support
core.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qZAXd-005pUP-JL@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move the setup of gmac4 speicifc phylink capabilities into gmac4 code.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qZAXY-005pUJ-Ez@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Allow MACs to provide their own capabilities via the MAC operations
struct.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qZAXT-005pUD-Aj@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use phylink_limit_mac_speed() to limit the MAC capabilities rather
than coding this for each speed.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qZAXO-005pU7-61@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We have a local variable for priv->plat->mdio_bus_data, which we use
later in the conditional if() block, but we evaluate the above within
the conditional expression. Use mdio_bus_data instead. Since these
will be the only two users of this local variable, move its assignment
just before the if().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qZAXJ-005pU1-1z@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move the initialisation of the fwnode variable closer to its use
site, rather than scattered throughout stmmac_phy_setup().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qZAXD-005pTv-TN@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
All users of plat->phylink_node first convert it to a fwnode. Rather
than repeatedly convert to a fwnode, store it as a fwnode. To reflect
this change, call it plat->port_node instead - it is used for more
than just phylink.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qZAX8-005pTo-OT@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a function which can be used to limit the phylink MAC capabilities
to an upper speed limit.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qZAX3-005pTi-K1@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When an skb fails to be forwarded to the peer(e.g., skb data buffer
length exceeds MTU), it will not be added to the peer's receive queue.
Therefore, we should schedule the peer's NAPI poll function only when
skb forwarding is successful to avoid unnecessary overhead.
Signed-off-by: Liang Chen <liangchen.linux@gmail.com>
Link: https://lore.kernel.org/r/20230824123131.7673-1-liangchen.linux@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.6
The second pull request for v6.6, this time with both stack and driver
changes. Unusually we have only one major new feature but lots of
small cleanup all over, I guess this is due to people have been on
vacation the last month.
Major changes:
rtw89
- Introduce Time Averaged SAR (TAS) support
* tag 'wireless-next-2023-08-25' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (114 commits)
wifi: rtlwifi: rtl8723: Remove unused function rtl8723_cmd_send_packet()
wifi: rtw88: usb: kill and free rx urbs on probe failure
wifi: rtw89: Fix clang -Wimplicit-fallthrough in rtw89_query_sar()
wifi: rtw89: phy: modify register setting of ENV_MNTR, PHYSTS and DIG
wifi: rtw89: phy: add phy_gen_def::cr_base to support WiFi 7 chips
wifi: rtw89: mac: define register address of rx_filter to generalize code
wifi: rtw89: mac: define internal memory address for WiFi 7 chip
wifi: rtw89: mac: generalize code to indirectly access WiFi internal memory
wifi: rtw89: mac: add mac_gen_def::band1_offset to map MAC band1 register address
wifi: wlcore: sdio: Use module_sdio_driver macro to simplify the code
wifi: rtw89: initialize multi-channel handling
wifi: rtw89: provide functions to configure NoA for beacon update
wifi: rtw89: call rtw89_chan_get() by vif chanctx if aware of vif
wifi: rtw89: sar: let caller decide the center frequency to query
wifi: rtw89: refine rtw89_correct_cck_chan() by rtw89_hw_to_nl80211_band()
wifi: rtw89: add function prototype for coex request duration
Fix nomenclature for USB and PCI wireless devices
wifi: ath: Use is_multicast_ether_addr() to check multicast Ether address
wifi: ath12k: Remove unused declarations
wifi: ath12k: add check max message length while scanning with extraie
...
====================
Link: https://lore.kernel.org/r/20230825132230.A0833C433C8@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
Luiz Augusto von Dentz says:
====================
bluetooth-next pull request for net-next:
- Introduce HCI_QUIRK_BROKEN_LE_CODED
- Add support for PA/BIG sync
- Add support for NXP IW624 chipset
- Add support for Qualcomm WCN7850
* tag 'for-net-next-2023-08-24' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next:
Bluetooth: btusb: Do not call kfree_skb() under spin_lock_irqsave()
Bluetooth: btusb: Fix quirks table naming
Bluetooth: HCI: Introduce HCI_QUIRK_BROKEN_LE_CODED
Bluetooth: btintel: Send new command for PPAG
Bluetooth: ISO: Add support for periodic adv reports processing
Bluetooth: hci_conn: fail SCO/ISO via hci_conn_failed if ACL gone early
Bluetooth: hci_core: Fix missing instances using HCI_MAX_AD_LENGTH
Bluetooth: ISO: Use defer setup to separate PA sync and BIG sync
Bluetooth: qca: add support for WCN7850
Bluetooth: qca: use switch case for soc type behavior
dt-bindings: net: bluetooth: qualcomm: document WCN7850 chipset
Bluetooth: hci_conn: Fix sending BT_HCI_CMD_LE_CREATE_CONN_CANCEL
Bluetooth: hci_sync: Fix UAF in hci_disconnect_all_sync
Bluetooth: btnxpuart: Improve inband Independent Reset handling
Bluetooth: btnxpuart: Add support for IW624 chipset
Bluetooth: btnxpuart: Remove check for CTS low after FW download
====================
Link: https://lore.kernel.org/r/20230824201458.2577-1-luiz.dentz@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
ath.git patches for v6.6. No major changes, only smaller fixes and
cleanups this time.
|
|
The function rtl8723_cmd_send_packet() is not used anywhere, so remove it.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230824062339.1885385-1-ruanjinjie@huawei.com
|
|
After rtw_usb_alloc_rx_bufs() has been called rx urbs have been
allocated and must be freed in the error path. After rtw_usb_init_rx()
has been called they are submitted, so they also must be killed.
Add these forgotten steps to the probe error path.
Besides the lost memory this also fixes a problem when the driver
fails to download the firmware in rtw_chip_info_setup(). In this
case it can happen that the completion of the rx urbs handler runs
at a time when we already freed our data structures resulting in
a kernel crash.
Fixes: a82dfd33d123 ("wifi: rtw88: Add common USB chip support")
Cc: stable@vger.kernel.org
Reported-by: Ilgaz Öcal <ilgaz@ilgaz.gen.tr>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230823075021.588596-1-s.hauer@pengutronix.de
|
|
clang warns (or errors with CONFIG_WERROR=y):
drivers/net/wireless/realtek/rtw89/sar.c:216:3: error: unannotated fall-through between switch labels [-Werror,-Wimplicit-fallthrough]
216 | case RTW89_TAS_STATE_DPR_FORBID:
| ^
drivers/net/wireless/realtek/rtw89/sar.c:216:3: note: insert 'break;' to avoid fall-through
216 | case RTW89_TAS_STATE_DPR_FORBID:
| ^
| break;
1 error generated.
Clang is a little more pedantic than GCC, which does not warn when
falling through to a case that is just break or return. Clang's version
is more in line with the kernel's own stance in deprecated.rst, which
states that all switch/case blocks must end in either break,
fallthrough, continue, goto, or return. Add the missing break to silence
the warning.
Closes: https://github.com/ClangBuiltLinux/linux/issues/1921
Fixes: eb2624f55ad1 ("wifi: rtw89: Introduce Time Averaged SAR (TAS) feature")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230822-rtw89-tas-clang-implicit-fallthrough-v1-1-5cb73f0fa976@kernel.org
|
|
The ENV_MNTR(environment monitor) is the dynamic mechanism which based on
the HW of CCX(Cisco Compatible Extensions) which provide the channel
loading and noisy level indicator to debug or support the 802.11k. The
PHYSTS provide the detail PHY information per packet we received for
debugging. The DIG(dynamic initial gain) is the dynamic mechanism to
adjust the packet detect power level by received signal strength to avoid
false detection of the WiFi packet.
The address of registers used for ENV_MNTR, PHYSTS and DIG of WiFi 7 IC
are different with WiFi 6 series, so we modify the method to access the
register address in order to compatible with all WiFi 7 and 6 ICs.
Signed-off-by: Cheng-Chieh Hsieh <cj.hsieh@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230822125822.23817-7-pkshih@realtek.com
|
|
cr_base is base address of PHY control register. The base of WiFi 6 and 7
chips are 0x1_0000 and 0x2_0000 respectively, so define them accordingly.
For example, if PHY address is 0x1330, absolute address is 0x1_1330 for
WiFi 6 chips, and 0x2_1330 for WiFi 7 chips.
Meanwhile, there are two copies of PHY hardware named PHY0 and PHY1. The
offset between them is 0x2_0000, so the base address of PHY0 and PHY1 are
0x2_0000 and 0x4_0000 respectively.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230822125822.23817-6-pkshih@realtek.com
|
|
rx_filter is used to decide which kind of packets are received to driver,
or just dropped by MAC layer to reduce bus traffic.
The bit definitions of old and new chips are the sames, but only address
is changed, so define a field to generalize usage.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230822125822.23817-5-pkshih@realtek.com
|
|
Define base address of WiFi 7 internal memory according to design to
provide the same functions as existing WiFi 6 chips.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230822125822.23817-4-pkshih@realtek.com
|
|
To diagnose abnormal behavior, we need to dump certain internal memory.
For example, dump security CAM when debugging encryption/decryption
problems, or dump BA CAM when debugging abnormal BlockAck.
Since the indirect address and internal memory base address are different
between WiFi 6 and 7 chips, add fields to reuse codes.
Also, only WiFi 6 chips initialize DMAC and CMAC tables via this indirect
interface, so no need to change the constant register address, and
new firmware will help to initialize these tables.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230822125822.23817-3-pkshih@realtek.com
|
|
address
There are two copies of MAC hardware called band0 and band1. Basically,
the only difference between them is base address, so we can share functions
with a 'band' (or 'mac_idx') argument.
The offset of base address of WiFi 6 and 7 are 0x2000 and 0x4000
respectively, so add band1_offset field to new introduced struct
mac_gen_def to possibly reuse functions.
Using below spatch script to convert callers:
@@
expression reg, band;
@@
- rtw89_mac_reg_by_idx(reg, band)
+ rtw89_mac_reg_by_idx(rtwdev, reg, band)
@@
expression reg, port, band;
@@
- rtw89_mac_reg_by_port(reg, port, band)
+ rtw89_mac_reg_by_port(rtwdev, reg, port, band)
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230822125822.23817-2-pkshih@realtek.com
|
|
Use the module_sdio_driver macro to simplify the code, which is the
same as declaring with module_init() and module_exit().
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230821140345.3140493-1-lizetao1@huawei.com
|
|
We prepare to deal with multiple channels via new entity modes.
* MCC_PREPARE: Transitional mode before MCC
* MCC: Multi-Channel Concurrent mode
And, enum of sub-entity is extended for second channel context.
We add the entry flow of multi-channel handling and the core stuffs
for extended index of sub-entity. And, we now deal with the filling
of entity channels' info in entity recalc where we know the number
of active chanctx. However, the other detail coding of MCC start/stop
will be implemented in the following.
Besides, chanctx listener struct is pre-added in chip info. Each
component can add callback type in chanctx listener and configure
its callback function to react according to chanctx states. We know
at least RFK (RF calibration) and BTC (BT coexistence) will require
such callbacks.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230816082133.57474-7-pkshih@realtek.com
|
|
Callers call renew function when wanting to generate a new P2P NoA
information element, and call append function to append NoA attribute
one by one. Then, updating beacon work will fetch the P2P NoA information
element configured by callers and add it to beacon.
The use case of MCC (multi-channel concurrent) <GO + STA> for example:
* start MCC - GO part
renew P2P NoA
append period NoA after calculation
* download beacon for GO
fetch P2P NoA and add to beacon content
* stop MCC - GO part
renew P2P NoA (reset)
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230816082133.57474-6-pkshih@realtek.com
|
|
We adjust these processes which can work accodrding to vif but call
rtw89_chan_get() with static RTW89_SUB_ENTITY_0. After multi-channel
support, chanctx of vif won't always be on RTW89_SUB_ENTITY_0. So,
we make them call rtw89_chan_get() with rtwvif->sub_entity_idx.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230816082133.57474-5-pkshih@realtek.com
|
|
If multiple channels, SAR will be hard to determine the center frequency
to query. Therefore, we move this decision out of SAR.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230816082133.57474-4-pkshih@realtek.com
|
|
In rtw89_correct_cck_chan(), we turn to use rtw89_hw_to_nl80211_band().
The difference between rtw89_hw_to_nl80211_band() and the original raw
judgement is the case on 6 GHz. Since rtw89_correct_cck_chan() is common
code independent on chip, if runtime chip doesn't support 6 GHz, it is
probably safe. Otherwise, it might not.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230816082133.57474-3-pkshih@realtek.com
|