| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
With the addition of new MAC blocks like CN10K RPM and CN10KB
RPM_USX, LMACs are noncontiguous. Though in most of the functions,
lmac validation checks exist but in few functions they are missing.
This patch adds the same.
Signed-off-by: Hariprasad Kelam <[email protected]>
Signed-off-by: Sunil Kovvuri Goutham <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Don't treat lack of CGX LMACs on the system as a error.
Instead ignore it so that LBK VFs are created and can be used.
Signed-off-by: Sunil Goutham <[email protected]>
Signed-off-by: Hariprasad Kelam <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Upon physical link change, firmware reports to the kernel about the
change along with the details like speed, lmac_type_id, etc.
Kernel derives lmac_type based on lmac_type_id received from firmware.
This patch extends current lmac list with new USGMII mode supported
by CN10KB RPM block.
Signed-off-by: Hariprasad Kelam <[email protected]>
Signed-off-by: Sunil Kovvuri Goutham <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Implement devlink port function commands to enable / disable IPsec
packet offloads. This is used to control the IPsec capability of the
device.
When ipsec_offload is enabled for a VF, it prevents adding IPsec packet
offloads on the PF, because the two cannot be active simultaneously due
to HW constraints. Conversely, if there are any active IPsec packet
offloads on the PF, it's not allowed to enable ipsec_packet on a VF,
until PF IPsec offloads are cleared.
Signed-off-by: Dima Chumak <[email protected]>
Signed-off-by: Leon Romanovsky <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Implement devlink port function commands to enable / disable IPsec
crypto offloads. This is used to control the IPsec capability of the
device.
When ipsec_crypto is enabled for a VF, it prevents adding IPsec crypto
offloads on the PF, because the two cannot be active simultaneously due
to HW constraints. Conversely, if there are any active IPsec crypto
offloads on the PF, it's not allowed to enable ipsec_crypto on a VF,
until PF IPsec offloads are cleared.
Signed-off-by: Dima Chumak <[email protected]>
Signed-off-by: Leon Romanovsky <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
mlx5 HW can't perform IPsec offload operation simultaneously both on PF
and VFs at the same time. While the previous patches added devlink knobs
to change IPsec capabilities dynamically, there is a need to add a logic
to block such IPsec capabilities for the cases when IPsec is already
configured.
Signed-off-by: Leon Romanovsky <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
In the commit 366e46242b8e ("net/mlx5e: Make IPsec offload work together
with eswitch and TC"), new API to block IPsec vs. TC creation was introduced.
Internally, that API used devlink lock to avoid races with userspace, but it is
not really needed as dev->priv.eswitch is stable and can't be changed. So remove
dependency on devlink lock and move block encap code back to its original place.
Signed-off-by: Leon Romanovsky <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
There is no need in holding devlink lock as it gives nothing
compared to already used write mode_lock.
Signed-off-by: Leon Romanovsky <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
For AM65x SR2.0 it's required to enable IEP1 in raw 64bit mode which is
used by PRU FW to monitor the link and apply w/a for 10M link issue.
Note. No public errata available yet.
Without this w/a the PRU FW will stuck if link state changes under TX
traffic pressure.
Hence, add support for 10M full duplex for AM65x SR2.0:
- add new IEP API to enable IEP, but without PTP support
- add pdata quirk_10m_link_issue to enable 10M link issue w/a.
Signed-off-by: Grygorii Strashko <[email protected]>
Signed-off-by: Vignesh Raghavendra <[email protected]>
Reviewed-by: Roger Quadros <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Reviewed-by: Jacob Keller <[email protected]>
Signed-off-by: MD Danish Anwar <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Add packet timestamping TS and PTP PHC clock support.
For AM65x and AM64x:
- IEP1 is not used
- IEP0 is configured in shadow mode with 1ms cycle and shared between
Linux and FW. It provides time and TS in number cycles, so special
conversation in ns is required.
- IEP0 shared between PRUeth ports.
- IEP0 supports PPS, periodic output.
- IEP0 settime() and enabling PPS required FW interraction.
- RX TS provided with each packet in CPPI5 descriptor.
- TX TS returned through separate ICSSG hw queues for each port. TX TS
readiness is signaled by INTC IRQ. Only one packet at time can be requested
for TX TS.
Signed-off-by: Roger Quadros <[email protected]>
Co-developed-by: Grygorii Strashko <[email protected]>
Signed-off-by: Grygorii Strashko <[email protected]>
Signed-off-by: Vignesh Raghavendra <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Signed-off-by: MD Danish Anwar <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Add a driver for Industrial Ethernet Peripheral (IEP) block of PRUSS to
support timestamping of ethernet packets and thus support PTP and PPS
for PRU ethernet ports.
Signed-off-by: Roger Quadros <[email protected]>
Signed-off-by: Lokesh Vutla <[email protected]>
Signed-off-by: Murali Karicheri <[email protected]>
Signed-off-by: Vignesh Raghavendra <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Signed-off-by: MD Danish Anwar <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Extend the pedit add actions to handle this case for ipv6. Similar to ipv4
dec ttl, decrementing ipv6 hop limit can be achieved by adding 0xff to the
hop limit field.
Co-developed-by: Edward Cree <[email protected]>
Signed-off-by: Edward Cree <[email protected]>
Signed-off-by: Pieter Jansen van Vuuren <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Introduce pedit add actions and use it to achieve decrement ttl offload.
Decrement ttl can be achieved by adding 0xff to the ttl field.
Co-developed-by: Edward Cree <[email protected]>
Signed-off-by: Edward Cree <[email protected]>
Signed-off-by: Pieter Jansen van Vuuren <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Offload pedit set ipv6 hop limit, where the hop limit has already been
matched and the new value is one less, by translating it to a decrement.
Co-developed-by: Edward Cree <[email protected]>
Signed-off-by: Edward Cree <[email protected]>
Signed-off-by: Pieter Jansen van Vuuren <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Offload pedit set ipv4 ttl field, where the ttl field has already been
matched and the new value is one less, by translating it to a decrement.
Co-developed-by: Edward Cree <[email protected]>
Signed-off-by: Edward Cree <[email protected]>
Signed-off-by: Pieter Jansen van Vuuren <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Introduce the first pedit set offload functionality for the sfc driver.
In addition to this, add offload functionality for both mac source and
destination pedit set actions.
Co-developed-by: Edward Cree <[email protected]>
Signed-off-by: Edward Cree <[email protected]>
Signed-off-by: Pieter Jansen van Vuuren <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Introduce the initial ethernet pedit set action infrastructure in
preparation for adding mac src and dst pedit action offloads.
Co-developed-by: Edward Cree <[email protected]>
Signed-off-by: Edward Cree <[email protected]>
Signed-off-by: Pieter Jansen van Vuuren <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-08-24 (igc, e1000e)
This series contains updates to igc and e1000e drivers.
Vinicius adds support for utilizing multiple PTP registers on igc.
Sasha reduces interval time for PTM on igc and adds new device support
on e1000e.
* '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
e1000e: Add support for the next LOM generation
igc: Decrease PTM short interval from 10 us to 1 us
igc: Add support for multiple in-flight TX timestamps
====================
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Rather than detecting when half-duplex is not supported, and clearing
the MAC capabilities, reverse the if() condition and use it to set the
capabilities instead.
Signed-off-by: Russell King (Oracle) <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Move priv->phylink_config.mac_managed_pm to be along side the other
phylink initialisations.
Signed-off-by: Russell King (Oracle) <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Move the xgmac specific phylink capabilities to the dwxgmac2 support
core.
Signed-off-by: Russell King (Oracle) <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Move the setup of gmac4 speicifc phylink capabilities into gmac4 code.
Signed-off-by: Russell King (Oracle) <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Allow MACs to provide their own capabilities via the MAC operations
struct.
Signed-off-by: Russell King (Oracle) <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Use phylink_limit_mac_speed() to limit the MAC capabilities rather
than coding this for each speed.
Signed-off-by: Russell King (Oracle) <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
We have a local variable for priv->plat->mdio_bus_data, which we use
later in the conditional if() block, but we evaluate the above within
the conditional expression. Use mdio_bus_data instead. Since these
will be the only two users of this local variable, move its assignment
just before the if().
Signed-off-by: Russell King (Oracle) <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Move the initialisation of the fwnode variable closer to its use
site, rather than scattered throughout stmmac_phy_setup().
Signed-off-by: Russell King (Oracle) <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
All users of plat->phylink_node first convert it to a fwnode. Rather
than repeatedly convert to a fwnode, store it as a fwnode. To reflect
this change, call it plat->port_node instead - it is used for more
than just phylink.
Signed-off-by: Russell King (Oracle) <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Add a function which can be used to limit the phylink MAC capabilities
to an upper speed limit.
Signed-off-by: Russell King (Oracle) <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
When an skb fails to be forwarded to the peer(e.g., skb data buffer
length exceeds MTU), it will not be added to the peer's receive queue.
Therefore, we should schedule the peer's NAPI poll function only when
skb forwarding is successful to avoid unnecessary overhead.
Signed-off-by: Liang Chen <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.6
The second pull request for v6.6, this time with both stack and driver
changes. Unusually we have only one major new feature but lots of
small cleanup all over, I guess this is due to people have been on
vacation the last month.
Major changes:
rtw89
- Introduce Time Averaged SAR (TAS) support
* tag 'wireless-next-2023-08-25' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (114 commits)
wifi: rtlwifi: rtl8723: Remove unused function rtl8723_cmd_send_packet()
wifi: rtw88: usb: kill and free rx urbs on probe failure
wifi: rtw89: Fix clang -Wimplicit-fallthrough in rtw89_query_sar()
wifi: rtw89: phy: modify register setting of ENV_MNTR, PHYSTS and DIG
wifi: rtw89: phy: add phy_gen_def::cr_base to support WiFi 7 chips
wifi: rtw89: mac: define register address of rx_filter to generalize code
wifi: rtw89: mac: define internal memory address for WiFi 7 chip
wifi: rtw89: mac: generalize code to indirectly access WiFi internal memory
wifi: rtw89: mac: add mac_gen_def::band1_offset to map MAC band1 register address
wifi: wlcore: sdio: Use module_sdio_driver macro to simplify the code
wifi: rtw89: initialize multi-channel handling
wifi: rtw89: provide functions to configure NoA for beacon update
wifi: rtw89: call rtw89_chan_get() by vif chanctx if aware of vif
wifi: rtw89: sar: let caller decide the center frequency to query
wifi: rtw89: refine rtw89_correct_cck_chan() by rtw89_hw_to_nl80211_band()
wifi: rtw89: add function prototype for coex request duration
Fix nomenclature for USB and PCI wireless devices
wifi: ath: Use is_multicast_ether_addr() to check multicast Ether address
wifi: ath12k: Remove unused declarations
wifi: ath12k: add check max message length while scanning with extraie
...
====================
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
Luiz Augusto von Dentz says:
====================
bluetooth-next pull request for net-next:
- Introduce HCI_QUIRK_BROKEN_LE_CODED
- Add support for PA/BIG sync
- Add support for NXP IW624 chipset
- Add support for Qualcomm WCN7850
* tag 'for-net-next-2023-08-24' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next:
Bluetooth: btusb: Do not call kfree_skb() under spin_lock_irqsave()
Bluetooth: btusb: Fix quirks table naming
Bluetooth: HCI: Introduce HCI_QUIRK_BROKEN_LE_CODED
Bluetooth: btintel: Send new command for PPAG
Bluetooth: ISO: Add support for periodic adv reports processing
Bluetooth: hci_conn: fail SCO/ISO via hci_conn_failed if ACL gone early
Bluetooth: hci_core: Fix missing instances using HCI_MAX_AD_LENGTH
Bluetooth: ISO: Use defer setup to separate PA sync and BIG sync
Bluetooth: qca: add support for WCN7850
Bluetooth: qca: use switch case for soc type behavior
dt-bindings: net: bluetooth: qualcomm: document WCN7850 chipset
Bluetooth: hci_conn: Fix sending BT_HCI_CMD_LE_CREATE_CONN_CANCEL
Bluetooth: hci_sync: Fix UAF in hci_disconnect_all_sync
Bluetooth: btnxpuart: Improve inband Independent Reset handling
Bluetooth: btnxpuart: Add support for IW624 chipset
Bluetooth: btnxpuart: Remove check for CTS low after FW download
====================
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
ath.git patches for v6.6. No major changes, only smaller fixes and
cleanups this time.
|
|
The function rtl8723_cmd_send_packet() is not used anywhere, so remove it.
Signed-off-by: Jinjie Ruan <[email protected]>
Acked-by: Ping-Ke Shih <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
After rtw_usb_alloc_rx_bufs() has been called rx urbs have been
allocated and must be freed in the error path. After rtw_usb_init_rx()
has been called they are submitted, so they also must be killed.
Add these forgotten steps to the probe error path.
Besides the lost memory this also fixes a problem when the driver
fails to download the firmware in rtw_chip_info_setup(). In this
case it can happen that the completion of the rx urbs handler runs
at a time when we already freed our data structures resulting in
a kernel crash.
Fixes: a82dfd33d123 ("wifi: rtw88: Add common USB chip support")
Cc: [email protected]
Reported-by: Ilgaz Öcal <[email protected]>
Signed-off-by: Sascha Hauer <[email protected]>
Acked-by: Larry Finger <[email protected]>
Acked-by: Ping-Ke Shih <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
clang warns (or errors with CONFIG_WERROR=y):
drivers/net/wireless/realtek/rtw89/sar.c:216:3: error: unannotated fall-through between switch labels [-Werror,-Wimplicit-fallthrough]
216 | case RTW89_TAS_STATE_DPR_FORBID:
| ^
drivers/net/wireless/realtek/rtw89/sar.c:216:3: note: insert 'break;' to avoid fall-through
216 | case RTW89_TAS_STATE_DPR_FORBID:
| ^
| break;
1 error generated.
Clang is a little more pedantic than GCC, which does not warn when
falling through to a case that is just break or return. Clang's version
is more in line with the kernel's own stance in deprecated.rst, which
states that all switch/case blocks must end in either break,
fallthrough, continue, goto, or return. Add the missing break to silence
the warning.
Closes: https://github.com/ClangBuiltLinux/linux/issues/1921
Fixes: eb2624f55ad1 ("wifi: rtw89: Introduce Time Averaged SAR (TAS) feature")
Signed-off-by: Nathan Chancellor <[email protected]>
Reviewed-by: Nick Desaulniers <[email protected]>
Acked-by: Ping-Ke Shih <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Link: https://lore.kernel.org/r/20230822-rtw89-tas-clang-implicit-fallthrough-v1-1-5cb73f0fa976@kernel.org
|
|
The ENV_MNTR(environment monitor) is the dynamic mechanism which based on
the HW of CCX(Cisco Compatible Extensions) which provide the channel
loading and noisy level indicator to debug or support the 802.11k. The
PHYSTS provide the detail PHY information per packet we received for
debugging. The DIG(dynamic initial gain) is the dynamic mechanism to
adjust the packet detect power level by received signal strength to avoid
false detection of the WiFi packet.
The address of registers used for ENV_MNTR, PHYSTS and DIG of WiFi 7 IC
are different with WiFi 6 series, so we modify the method to access the
register address in order to compatible with all WiFi 7 and 6 ICs.
Signed-off-by: Cheng-Chieh Hsieh <[email protected]>
Signed-off-by: Ping-Ke Shih <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
cr_base is base address of PHY control register. The base of WiFi 6 and 7
chips are 0x1_0000 and 0x2_0000 respectively, so define them accordingly.
For example, if PHY address is 0x1330, absolute address is 0x1_1330 for
WiFi 6 chips, and 0x2_1330 for WiFi 7 chips.
Meanwhile, there are two copies of PHY hardware named PHY0 and PHY1. The
offset between them is 0x2_0000, so the base address of PHY0 and PHY1 are
0x2_0000 and 0x4_0000 respectively.
Signed-off-by: Ping-Ke Shih <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
rx_filter is used to decide which kind of packets are received to driver,
or just dropped by MAC layer to reduce bus traffic.
The bit definitions of old and new chips are the sames, but only address
is changed, so define a field to generalize usage.
Signed-off-by: Ping-Ke Shih <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Define base address of WiFi 7 internal memory according to design to
provide the same functions as existing WiFi 6 chips.
Signed-off-by: Ping-Ke Shih <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
To diagnose abnormal behavior, we need to dump certain internal memory.
For example, dump security CAM when debugging encryption/decryption
problems, or dump BA CAM when debugging abnormal BlockAck.
Since the indirect address and internal memory base address are different
between WiFi 6 and 7 chips, add fields to reuse codes.
Also, only WiFi 6 chips initialize DMAC and CMAC tables via this indirect
interface, so no need to change the constant register address, and
new firmware will help to initialize these tables.
Signed-off-by: Ping-Ke Shih <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
address
There are two copies of MAC hardware called band0 and band1. Basically,
the only difference between them is base address, so we can share functions
with a 'band' (or 'mac_idx') argument.
The offset of base address of WiFi 6 and 7 are 0x2000 and 0x4000
respectively, so add band1_offset field to new introduced struct
mac_gen_def to possibly reuse functions.
Using below spatch script to convert callers:
@@
expression reg, band;
@@
- rtw89_mac_reg_by_idx(reg, band)
+ rtw89_mac_reg_by_idx(rtwdev, reg, band)
@@
expression reg, port, band;
@@
- rtw89_mac_reg_by_port(reg, port, band)
+ rtw89_mac_reg_by_port(rtwdev, reg, port, band)
Signed-off-by: Ping-Ke Shih <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Use the module_sdio_driver macro to simplify the code, which is the
same as declaring with module_init() and module_exit().
Signed-off-by: Li Zetao <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
We prepare to deal with multiple channels via new entity modes.
* MCC_PREPARE: Transitional mode before MCC
* MCC: Multi-Channel Concurrent mode
And, enum of sub-entity is extended for second channel context.
We add the entry flow of multi-channel handling and the core stuffs
for extended index of sub-entity. And, we now deal with the filling
of entity channels' info in entity recalc where we know the number
of active chanctx. However, the other detail coding of MCC start/stop
will be implemented in the following.
Besides, chanctx listener struct is pre-added in chip info. Each
component can add callback type in chanctx listener and configure
its callback function to react according to chanctx states. We know
at least RFK (RF calibration) and BTC (BT coexistence) will require
such callbacks.
Signed-off-by: Zong-Zhe Yang <[email protected]>
Signed-off-by: Ping-Ke Shih <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Callers call renew function when wanting to generate a new P2P NoA
information element, and call append function to append NoA attribute
one by one. Then, updating beacon work will fetch the P2P NoA information
element configured by callers and add it to beacon.
The use case of MCC (multi-channel concurrent) <GO + STA> for example:
* start MCC - GO part
renew P2P NoA
append period NoA after calculation
* download beacon for GO
fetch P2P NoA and add to beacon content
* stop MCC - GO part
renew P2P NoA (reset)
Signed-off-by: Zong-Zhe Yang <[email protected]>
Signed-off-by: Ping-Ke Shih <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
We adjust these processes which can work accodrding to vif but call
rtw89_chan_get() with static RTW89_SUB_ENTITY_0. After multi-channel
support, chanctx of vif won't always be on RTW89_SUB_ENTITY_0. So,
we make them call rtw89_chan_get() with rtwvif->sub_entity_idx.
Signed-off-by: Zong-Zhe Yang <[email protected]>
Signed-off-by: Ping-Ke Shih <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
If multiple channels, SAR will be hard to determine the center frequency
to query. Therefore, we move this decision out of SAR.
Signed-off-by: Zong-Zhe Yang <[email protected]>
Signed-off-by: Ping-Ke Shih <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
In rtw89_correct_cck_chan(), we turn to use rtw89_hw_to_nl80211_band().
The difference between rtw89_hw_to_nl80211_band() and the original raw
judgement is the case on 6 GHz. Since rtw89_correct_cck_chan() is common
code independent on chip, if runtime chip doesn't support 6 GHz, it is
probably safe. Otherwise, it might not.
Signed-off-by: Zong-Zhe Yang <[email protected]>
Signed-off-by: Ping-Ke Shih <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
The request duration comes from coex mechanism, indicating the
length of time that should be reserved for BT in each time division.
It is required to handle update notification when channel concurrency
processes. Since it will involve in both coex and wifi code flow, this
commit ahead adds the prototype for required function interfaces to
split the implementation of coex and wifi in the following.
The follow-up are expected be add afterwards.
1. coex mechanism call rtw89_core_ntfy_btc_event() once bt req len changes
2. channel concurrency flow updates related stuffs when notified
Signed-off-by: Zong-Zhe Yang <[email protected]>
Signed-off-by: Ping-Ke Shih <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
A mouse that uses a USB connection is called a "USB mouse" device (or
"USB mouse" for short), not a "mouse USB" device. By analogy, a WiFi
adapter that connects to the host computer via USB is a "USB wireless"
device, not a "wireless USB" device. (The latter term more properly
refers to a defunct Wireless USB specification, which described a
technology for sending USB protocol messages over an ultra wideband
radio link.)
Similarly for a WiFi adapter card that plugs into a PCIe slot: It is a
"PCIe wireless" device, not a "wireless PCIe" device.
Rephrase the text in the kernel source where the word ordering is
wrong.
Signed-off-by: Alan Stern <[email protected]>
Reviewed-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
The FEC driver supports the statistics for XDP actions except for
XDP_TX before, because the XDP_TX was not supported when adding
the statistics for XDP. Now the FEC driver has supported XDP_TX
since commit f601899e4321 ("net: fec: add XDP_TX feature support").
So it's reasonable and necessary to add statistics for XDP_TX.
Signed-off-by: Wei Fang <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|