| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Commit 89c290ea7589 ("ACPI: video: Put ACPI video and its child devices
into D0 on boot") introduced calling acpi_device_fix_up_power_extended()
on the video card for which the ACPI video bus is the companion device.
This unnecessarily touches the power-state of the GPU itself, while
the issue it tries to address only requires calling _PS0 on the child
devices.
Touching the power-state of the GPU itself is causing suspend / resume
issues on e.g. a Lenovo ThinkPad W530.
Instead use acpi_device_fix_up_power_children(), which only touches
the child devices, to fix this.
Fixes: 89c290ea7589 ("ACPI: video: Put ACPI video and its child devices into D0 on boot")
Reported-by: Owen T. Heisler <[email protected]>
Closes: https://lore.kernel.org/regressions/[email protected]/
Closes: https://gitlab.freedesktop.org/drm/nouveau/-/issues/273
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218124
Tested-by: Kai-Heng Feng <[email protected]>
Tested-by: Owen T. Heisler <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
Cc: 6.6+ <[email protected]> # 6.6+
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
In some cases it is necessary to fix-up the power-state of an ACPI
device's children without touching the ACPI device itself add
a new acpi_device_fix_up_power_children() function for this.
Signed-off-by: Hans de Goede <[email protected]>
Cc: 6.6+ <[email protected]> # 6.6+
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
Xen HVM guests were observed taking triple-faults when attempting to
online a previously offlined vCPU.
Investigation showed that the fault was coming from a failing call
to lockdep_assert_irqs_disabled(), in load_current_idt() which was
too early in the CPU bringup to actually catch the exception and
report the failure cleanly.
This was a false positive, caused by acpi_idle_play_dead() setting
the per-cpu hardirqs_enabled flag by calling safe_halt(). Switch it
to use raw_safe_halt() instead, which doesn't do so.
Signed-off-by: David Woodhouse <[email protected]>
Acked-by: Peter Zijlstra (Intel) <[email protected]>
Cc: 6.6+ <[email protected]> # 6.6+
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
In run_cache_set() after c->root returned from bch_btree_node_get(), it
is checked by IS_ERR_OR_NULL(). Indeed it is unncessary to check NULL
because bch_btree_node_get() will not return NULL pointer to caller.
This patch replaces IS_ERR_OR_NULL() by IS_ERR() for the above reason.
Signed-off-by: Coly Li <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jens Axboe <[email protected]>
|
|
This patch adds code comments to bch_btree_node_get() and
__bch_btree_node_alloc() that NULL pointer will not be returned and it
is unnecessary to check NULL pointer by the callers of these routines.
Signed-off-by: Coly Li <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jens Axboe <[email protected]>
|
|
Commit 028ddcac477b ("bcache: Remove unnecessary NULL point check in
node allocations") do the following change inside btree_gc_coalesce(),
31 @@ -1340,7 +1340,7 @@ static int btree_gc_coalesce(
32 memset(new_nodes, 0, sizeof(new_nodes));
33 closure_init_stack(&cl);
34
35 - while (nodes < GC_MERGE_NODES && !IS_ERR_OR_NULL(r[nodes].b))
36 + while (nodes < GC_MERGE_NODES && !IS_ERR(r[nodes].b))
37 keys += r[nodes++].keys;
38
39 blocks = btree_default_blocks(b->c) * 2 / 3;
At line 35 the original r[nodes].b is not always allocatored from
__bch_btree_node_alloc(), and possibly initialized as NULL pointer by
caller of btree_gc_coalesce(). Therefore the change at line 36 is not
correct.
This patch replaces the mistaken IS_ERR() by IS_ERR_OR_NULL() to avoid
potential issue.
Fixes: 028ddcac477b ("bcache: Remove unnecessary NULL point check in node allocations")
Cc: <[email protected]> # 6.5+
Cc: Zheng Wang <[email protected]>
Signed-off-by: Coly Li <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jens Axboe <[email protected]>
|
|
We get a kernel crash about "unable to handle kernel paging request":
```dmesg
[368033.032005] BUG: unable to handle kernel paging request at ffffffffad9ae4b5
[368033.032007] PGD fc3a0d067 P4D fc3a0d067 PUD fc3a0e063 PMD 8000000fc38000e1
[368033.032012] Oops: 0003 [#1] SMP PTI
[368033.032015] CPU: 23 PID: 55090 Comm: bch_dirtcnt[0] Kdump: loaded Tainted: G OE --------- - - 4.18.0-147.5.1.es8_24.x86_64 #1
[368033.032017] Hardware name: Tsinghua Tongfang THTF Chaoqiang Server/072T6D, BIOS 2.4.3 01/17/2017
[368033.032027] RIP: 0010:native_queued_spin_lock_slowpath+0x183/0x1d0
[368033.032029] Code: 8b 02 48 85 c0 74 f6 48 89 c1 eb d0 c1 e9 12 83 e0
03 83 e9 01 48 c1 e0 05 48 63 c9 48 05 c0 3d 02 00 48 03 04 cd 60 68 93
ad <48> 89 10 8b 42 08 85 c0 75 09 f3 90 8b 42 08 85 c0 74 f7 48 8b 02
[368033.032031] RSP: 0018:ffffbb48852abe00 EFLAGS: 00010082
[368033.032032] RAX: ffffffffad9ae4b5 RBX: 0000000000000246 RCX: 0000000000003bf3
[368033.032033] RDX: ffff97b0ff8e3dc0 RSI: 0000000000600000 RDI: ffffbb4884743c68
[368033.032034] RBP: 0000000000000001 R08: 0000000000000000 R09: 000007ffffffffff
[368033.032035] R10: ffffbb486bb01000 R11: 0000000000000001 R12: ffffffffc068da70
[368033.032036] R13: 0000000000000003 R14: 0000000000000000 R15: 0000000000000000
[368033.032038] FS: 0000000000000000(0000) GS:ffff97b0ff8c0000(0000) knlGS:0000000000000000
[368033.032039] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[368033.032040] CR2: ffffffffad9ae4b5 CR3: 0000000fc3a0a002 CR4: 00000000003626e0
[368033.032042] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[368033.032043] bcache: bch_cached_dev_attach() Caching rbd479 as bcache462 on set 8cff3c36-4a76-4242-afaa-7630206bc70b
[368033.032045] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[368033.032046] Call Trace:
[368033.032054] _raw_spin_lock_irqsave+0x32/0x40
[368033.032061] __wake_up_common_lock+0x63/0xc0
[368033.032073] ? bch_ptr_invalid+0x10/0x10 [bcache]
[368033.033502] bch_dirty_init_thread+0x14c/0x160 [bcache]
[368033.033511] ? read_dirty_submit+0x60/0x60 [bcache]
[368033.033516] kthread+0x112/0x130
[368033.033520] ? kthread_flush_work_fn+0x10/0x10
[368033.034505] ret_from_fork+0x35/0x40
```
The crash occurred when call wake_up(&state->wait), and then we want
to look at the value in the state. However, bch_sectors_dirty_init()
is not found in the stack of any task. Since state is allocated on
the stack, we guess that bch_sectors_dirty_init() has exited, causing
bch_dirty_init_thread() to be unable to handle kernel paging request.
In order to verify this idea, we added some printing information during
wake_up(&state->wait). We find that "wake up" is printed twice, however
we only expect the last thread to wake up once.
```dmesg
[ 994.641004] alcache: bch_dirty_init_thread() wake up
[ 994.641018] alcache: bch_dirty_init_thread() wake up
[ 994.641523] alcache: bch_sectors_dirty_init() init exit
```
There is a race. If bch_sectors_dirty_init() exits after the first wake
up, the second wake up will trigger this bug("unable to handle kernel
paging request").
Proceed as follows:
bch_sectors_dirty_init
kthread_run ==============> bch_dirty_init_thread(bch_dirtcnt[0])
... ...
atomic_inc(&state.started) ...
... ...
atomic_read(&state.enough) ...
... atomic_set(&state->enough, 1)
kthread_run ======================================================> bch_dirty_init_thread(bch_dirtcnt[1])
... atomic_dec_and_test(&state->started) ...
atomic_inc(&state.started) ... ...
... wake_up(&state->wait) ...
atomic_read(&state.enough) atomic_dec_and_test(&state->started)
... ...
wait_event(state.wait, atomic_read(&state.started) == 0) ...
return ...
wake_up(&state->wait)
We believe it is very common to wake up twice if there is no dirty, but
crash is an extremely low probability event. It's hard for us to reproduce
this issue. We attached and detached continuously for a week, with a total
of more than one million attaches and only one crash.
Putting atomic_inc(&state.started) before kthread_run() can avoid waking
up twice.
Fixes: b144e45fc576 ("bcache: make bch_sectors_dirty_init() to be multithreaded")
Signed-off-by: Mingzhe Zou <[email protected]>
Cc: <[email protected]>
Signed-off-by: Coly Li <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jens Axboe <[email protected]>
|
|
We had a problem with io hung because it was waiting for c->root to
release the lock.
crash> cache_set.root -l cache_set.list ffffa03fde4c0050
root = 0xffff802ef454c800
crash> btree -o 0xffff802ef454c800 | grep rw_semaphore
[ffff802ef454c858] struct rw_semaphore lock;
crash> struct rw_semaphore ffff802ef454c858
struct rw_semaphore {
count = {
counter = -4294967297
},
wait_list = {
next = 0xffff00006786fc28,
prev = 0xffff00005d0efac8
},
wait_lock = {
raw_lock = {
{
val = {
counter = 0
},
{
locked = 0 '\000',
pending = 0 '\000'
},
{
locked_pending = 0,
tail = 0
}
}
}
},
osq = {
tail = {
counter = 0
}
},
owner = 0xffffa03fdc586603
}
The "counter = -4294967297" means that lock count is -1 and a write lock
is being attempted. Then, we found that there is a btree with a counter
of 1 in btree_cache_freeable.
crash> cache_set -l cache_set.list ffffa03fde4c0050 -o|grep btree_cache
[ffffa03fde4c1140] struct list_head btree_cache;
[ffffa03fde4c1150] struct list_head btree_cache_freeable;
[ffffa03fde4c1160] struct list_head btree_cache_freed;
[ffffa03fde4c1170] unsigned int btree_cache_used;
[ffffa03fde4c1178] wait_queue_head_t btree_cache_wait;
[ffffa03fde4c1190] struct task_struct *btree_cache_alloc_lock;
crash> list -H ffffa03fde4c1140|wc -l
973
crash> list -H ffffa03fde4c1150|wc -l
1123
crash> cache_set.btree_cache_used -l cache_set.list ffffa03fde4c0050
btree_cache_used = 2097
crash> list -s btree -l btree.list -H ffffa03fde4c1140|grep -E -A2 "^ lock = {" > btree_cache.txt
crash> list -s btree -l btree.list -H ffffa03fde4c1150|grep -E -A2 "^ lock = {" > btree_cache_freeable.txt
[root@node-3 127.0.0.1-2023-08-04-16:40:28]# pwd
/var/crash/127.0.0.1-2023-08-04-16:40:28
[root@node-3 127.0.0.1-2023-08-04-16:40:28]# cat btree_cache.txt|grep counter|grep -v "counter = 0"
[root@node-3 127.0.0.1-2023-08-04-16:40:28]# cat btree_cache_freeable.txt|grep counter|grep -v "counter = 0"
counter = 1
We found that this is a bug in bch_sectors_dirty_init() when locking c->root:
(1). Thread X has locked c->root(A) write.
(2). Thread Y failed to lock c->root(A), waiting for the lock(c->root A).
(3). Thread X bch_btree_set_root() changes c->root from A to B.
(4). Thread X releases the lock(c->root A).
(5). Thread Y successfully locks c->root(A).
(6). Thread Y releases the lock(c->root B).
down_write locked ---(1)----------------------┐
| |
| down_read waiting ---(2)----┐ |
| | ┌-------------┐ ┌-------------┐
bch_btree_set_root ===(3)========>> | c->root A | | c->root B |
| | └-------------┘ └-------------┘
up_write ---(4)---------------------┘ | |
| | |
down_read locked ---(5)-----------┘ |
| |
up_read ---(6)-----------------------------┘
Since c->root may change, the correct steps to lock c->root should be
the same as bch_root_usage(), compare after locking.
static unsigned int bch_root_usage(struct cache_set *c)
{
unsigned int bytes = 0;
struct bkey *k;
struct btree *b;
struct btree_iter iter;
goto lock_root;
do {
rw_unlock(false, b);
lock_root:
b = c->root;
rw_lock(false, b, b->level);
} while (b != c->root);
for_each_key_filter(&b->keys, k, &iter, bch_ptr_bad)
bytes += bkey_bytes(k);
rw_unlock(false, b);
return (bytes * 100) / btree_bytes(c);
}
Fixes: b144e45fc576 ("bcache: make bch_sectors_dirty_init() to be multithreaded")
Signed-off-by: Mingzhe Zou <[email protected]>
Cc: <[email protected]>
Signed-off-by: Coly Li <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jens Axboe <[email protected]>
|
|
We found that after long run, the dirty_data of the bcache device
will have errors. This error cannot be eliminated unless re-register.
We also found that reattach after detach, this error can accumulate.
In bch_sectors_dirty_init(), all inode <= d->id keys will be recounted
again. This is wrong, we only need to count the keys of the current
device.
Fixes: b144e45fc576 ("bcache: make bch_sectors_dirty_init() to be multithreaded")
Signed-off-by: Mingzhe Zou <[email protected]>
Cc: <[email protected]>
Signed-off-by: Coly Li <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jens Axboe <[email protected]>
|
|
In SHOW(), the variable 'n' is of type 'size_t.' While there is a
conditional check to verify that 'n' is not equal to zero before
executing the 'do_div' macro, concerns arise regarding potential
division by zero error in 64-bit environments.
The concern arises when 'n' is 64 bits in size, greater than zero, and
the lower 32 bits of it are zeros. In such cases, the conditional check
passes because 'n' is non-zero, but the 'do_div' macro casts 'n' to
'uint32_t,' effectively truncating it to its lower 32 bits.
Consequently, the 'n' value becomes zero.
To fix this potential division by zero error and ensure precise
division handling, this commit replaces the 'do_div' macro with
div64_u64(). div64_u64() is designed to work with 64-bit operands,
guaranteeing that division is performed correctly.
This change enhances the robustness of the code, ensuring that division
operations yield accurate results in all scenarios, eliminating the
possibility of division by zero, and improving compatibility across
different 64-bit environments.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Rand Deeb <[email protected]>
Cc: <[email protected]>
Signed-off-by: Coly Li <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jens Axboe <[email protected]>
|
|
Variable cur_idx is being initialized with a value that is never read,
it is being re-assigned later in a while-loop. Remove the redundant
assignment. Cleans up clang scan build warning:
drivers/md/bcache/writeback.c:916:2: warning: Value stored to 'cur_idx'
is never read [deadcode.DeadStores]
Signed-off-by: Colin Ian King <[email protected]>
Reviewed-by: Coly Li <[email protected]>
Signed-off-by: Coly Li <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jens Axboe <[email protected]>
|
|
In btree_gc_rewrite_node(), pointer 'n' is not checked after it returns
from btree_gc_rewrite_node(). There is potential possibility that 'n' is
a non NULL ERR_PTR(), referencing such error code is not permitted in
following code. Therefore a return value checking is necessary after 'n'
is back from btree_node_alloc_replacement().
Signed-off-by: Coly Li <[email protected]>
Reported-by: Dan Carpenter <[email protected]>
Cc: <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jens Axboe <[email protected]>
|
|
Arraies bcache->stripe_sectors_dirty and bcache->full_dirty_stripes are
used for dirty data writeback, their sizes are decided by backing device
capacity and stripe size. Larger backing device capacity or smaller
stripe size make these two arraies occupies more dynamic memory space.
Currently bcache->stripe_size is directly inherited from
queue->limits.io_opt of underlying storage device. For normal hard
drives, its limits.io_opt is 0, and bcache sets the corresponding
stripe_size to 1TB (1<<31 sectors), it works fine 10+ years. But for
devices do declare value for queue->limits.io_opt, small stripe_size
(comparing to 1TB) becomes an issue for oversize memory allocations of
bcache->stripe_sectors_dirty and bcache->full_dirty_stripes, while the
capacity of hard drives gets much larger in recent decade.
For example a raid5 array assembled by three 20TB hardrives, the raid
device capacity is 40TB with typical 512KB limits.io_opt. After the math
calculation in bcache code, these two arraies will occupy 400MB dynamic
memory. Even worse Andrea Tomassetti reports that a 4KB limits.io_opt is
declared on a new 2TB hard drive, then these two arraies request 2GB and
512MB dynamic memory from kzalloc(). The result is that bcache device
always fails to initialize on his system.
To avoid the oversize memory allocation, bcache->stripe_size should not
directly inherited by queue->limits.io_opt from the underlying device.
This patch defines BCH_MIN_STRIPE_SZ (4MB) as minimal bcache stripe size
and set bcache device's stripe size against the declared limits.io_opt
value from the underlying storage device,
- If the declared limits.io_opt > BCH_MIN_STRIPE_SZ, bcache device will
set its stripe size directly by this limits.io_opt value.
- If the declared limits.io_opt < BCH_MIN_STRIPE_SZ, bcache device will
set its stripe size by a value multiplying limits.io_opt and euqal or
large than BCH_MIN_STRIPE_SZ.
Then the minimal stripe size of a bcache device will always be >= 4MB.
For a 40TB raid5 device with 512KB limits.io_opt, memory occupied by
bcache->stripe_sectors_dirty and bcache->full_dirty_stripes will be 50MB
in total. For a 2TB hard drive with 4KB limits.io_opt, memory occupied
by these two arraies will be 2.5MB in total.
Such mount of memory allocated for bcache->stripe_sectors_dirty and
bcache->full_dirty_stripes is reasonable for most of storage devices.
Reported-by: Andrea Tomassetti <[email protected]>
Signed-off-by: Coly Li <[email protected]>
Reviewed-by: Eric Wheeler <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jens Axboe <[email protected]>
|
|
Use of DRM_FORMAT_RGB888 and DRM_FORMAT_BGR888 on e.g. RK3288, RK3328
and RK3399 result in wrong colors being displayed.
The issue can be observed using modetest:
modetest -s <connector_id>@<crtc_id>:1920x1080-60@RG24
modetest -s <connector_id>@<crtc_id>:1920x1080-60@BG24
Vendor 4.4 kernel apply an inverted rb swap for these formats on VOP
full framework (IP version 3.x) compared to VOP little framework (2.x).
Fix colors by applying different rb swap for VOP full framework (3.x)
and VOP little framework (2.x) similar to vendor 4.4 kernel.
Fixes: 85a359f25388 ("drm/rockchip: Add BGR formats to VOP")
Signed-off-by: Jonas Karlman <[email protected]>
Tested-by: Diederik de Haas <[email protected]>
Reviewed-by: Christopher Obbard <[email protected]>
Tested-by: Christopher Obbard <[email protected]>
Signed-off-by: Heiko Stuebner <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
The only task of intel_gt_release_all is to zero gt table. Calling
it on error path prevents intel_gt_driver_late_release_all (called from
i915_driver_late_release) to cleanup GTs, causing leakage.
After i915_driver_late_release GT array is not used anymore so
it does not need cleaning at all.
Sample leak report:
BUG i915_request (...): Objects remaining in i915_request on __kmem_cache_shutdown()
...
Object 0xffff888113420040 @offset=64
Allocated in __i915_request_create+0x75/0x610 [i915] age=18339 cpu=1 pid=1454
kmem_cache_alloc+0x25b/0x270
__i915_request_create+0x75/0x610 [i915]
i915_request_create+0x109/0x290 [i915]
__engines_record_defaults+0xca/0x440 [i915]
intel_gt_init+0x275/0x430 [i915]
i915_gem_init+0x135/0x2c0 [i915]
i915_driver_probe+0x8d1/0xdc0 [i915]
v2: removed whole intel_gt_release_all
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/8489
Fixes: bec68cc9ea42 ("drm/i915: Prepare for multiple GTs")
Signed-off-by: Andrzej Hajda <[email protected]>
Reviewed-by: Tvrtko Ursulin <[email protected]>
Reviewed-by: Nirmoy Das <[email protected]>
Reviewed-by: Andi Shyti <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
(cherry picked from commit e899505533852bf1da133f2f4c9a9655ff77f7e5)
Signed-off-by: Jani Nikula <[email protected]>
|
|
After drm_connector_init() is called the connector is visible to the
rest of the kernel via the drm_mode_config::connector_list. Make
sure that the DSC AUX device and capabilities are setup by that time.
Another race condition is adding the connector to the connector list
before drm_connector_helper_add() sets the connector helper functions.
That's an unrelated issue, for which the fix is for a follow-up. One
solution would be adding the connector to the connector list only
during its registration in drm_connector_register().
Cc: Stanislav Lisovskiy <[email protected]>
Cc: Ville Syrjälä <[email protected]>
Fixes: 808b43fa7e56 ("drm/i915/dp_mst: Set connector DSC capabilities and decompression AUX")
Reviewed-by: Stanislav Lisovskiy <[email protected]>
Signed-off-by: Imre Deak <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
(cherry picked from commit 560ea72c76eb6d0c59f77580414e64cc09f1093d)
Signed-off-by: Jani Nikula <[email protected]>
|
|
md_end_clone_io() may overwrite error status in orig_bio->bi_status with
BLK_STS_OK. This could happen when orig_bio has BIO_CHAIN (split by
md_submit_bio => bio_split_to_limits, for example). As a result, upper
layer may miss error reported from md (or the device) and consider the
failed IO was successful.
Fix this by only update orig_bio->bi_status when current bio reports
error and orig_bio is BLK_STS_OK. This is the same behavior as
__bio_chain_endio().
Fixes: 10764815ff47 ("md: add io accounting for raid0 and raid5")
Cc: [email protected] # v5.14+
Reported-by: Bhanu Victor DiCara <[email protected]>
Closes: https://lore.kernel.org/regressions/5727380.DvuYhMxLoT@bvd0/
Signed-off-by: Song Liu <[email protected]>
Tested-by: Xiao Ni <[email protected]>
Reviewed-by: Yu Kuai <[email protected]>
Acked-by: Guoqing Jiang <[email protected]>
|
|
Add missing error return check for devm_ioport_map() and return the
error if this function call fails.
Fixes: 0d5ff566779f ("libata: convert to iomap")
Signed-off-by: Chen Ni <[email protected]>
Reviewed-by: Sergey Shtylyov <[email protected]>
Signed-off-by: Damien Le Moal <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fix from Borislav Petkov:
- Flush the translation service tables to prevent unpredictable
behavior on non-coherent GIC devices
* tag 'irq_urgent_for_v6.7_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic-v3-its: Flush ITS tables correctly in non-coherent GIC designs
|
|
During 'ifconfig <netdev> down' one RSS memory was not getting freed.
This patch fixes the same.
Fixes: 81a4362016e7 ("octeontx2-pf: Add RSS multi group support")
Signed-off-by: Suman Ghosh <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
wg_xmit() can be called concurrently, KCSAN reported [1]
some device stats updates can be lost.
Use DEV_STATS_INC() for this unlikely case.
[1]
BUG: KCSAN: data-race in wg_xmit / wg_xmit
read-write to 0xffff888104239160 of 8 bytes by task 1375 on cpu 0:
wg_xmit+0x60f/0x680 drivers/net/wireguard/device.c:231
__netdev_start_xmit include/linux/netdevice.h:4918 [inline]
netdev_start_xmit include/linux/netdevice.h:4932 [inline]
xmit_one net/core/dev.c:3543 [inline]
dev_hard_start_xmit+0x11b/0x3f0 net/core/dev.c:3559
...
read-write to 0xffff888104239160 of 8 bytes by task 1378 on cpu 1:
wg_xmit+0x60f/0x680 drivers/net/wireguard/device.c:231
__netdev_start_xmit include/linux/netdevice.h:4918 [inline]
netdev_start_xmit include/linux/netdevice.h:4932 [inline]
xmit_one net/core/dev.c:3543 [inline]
dev_hard_start_xmit+0x11b/0x3f0 net/core/dev.c:3559
...
v2: also change wg_packet_consume_data_done() (Hangbin Liu)
and wg_packet_purge_staged_packets()
Fixes: e7096c131e51 ("net: WireGuard secure network tunnel")
Reported-by: syzbot <[email protected]>
Signed-off-by: Eric Dumazet <[email protected]>
Cc: Jason A. Donenfeld <[email protected]>
Cc: Hangbin Liu <[email protected]>
Signed-off-by: Jason A. Donenfeld <[email protected]>
Reviewed-by: Hangbin Liu <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
When the device uses a custom subsystem vendor ID, the function
wx_sw_init() returns before the memory of 'wx->mac_table' is allocated.
The null pointer will causes the kernel panic.
Fixes: 79625f45ca73 ("net: wangxun: Move MAC address handling to libwx")
Signed-off-by: Jiawen Wu <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The Innolux G101ICE-L01 datasheet [1] page 17 table
6.1 INPUT SIGNAL TIMING SPECIFICATIONS
indicates that maximum vertical blanking time is 40 lines.
Currently the driver uses 29 lines.
Fix it, and since this panel is a DE panel, adjust the timings
to make them less hostile to controllers which cannot do 1 px
HSA/VSA, distribute the delays evenly between all three parts.
[1] https://www.data-modul.com/sites/default/files/products/G101ICE-L01-C2-specification-12042389.pdf
Fixes: 1e29b840af9f ("drm/panel: simple: Add Innolux G101ICE-L01 panel")
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Neil Armstrong <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Add missing .bus_flags = DRM_BUS_FLAG_DE_HIGH to this panel description,
ones which match both the datasheet and the panel display_timing flags .
Fixes: 1e29b840af9f ("drm/panel: simple: Add Innolux G101ICE-L01 panel")
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Neil Armstrong <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Seven small fixes, six in drivers and one in sd.
The sd fix is so large because it changes a struct pointer to a struct
but otherwise is fairly simple"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: qcom-ufs: dt-bindings: Document the SM8650 UFS Controller
scsi: sd: Fix sshdr use in sd_suspend_common()
scsi: scsi_debug: Delete some bogus error checking
scsi: scsi_debug: Fix some bugs in sdebug_error_write()
scsi: ufs: core: Fix racing issue between ufshcd_mcq_abort() and ISR
scsi: ufs: core: Expand MCQ queue slot to DeviceQueueDepth + 1
scsi: qla2xxx: Fix system crash due to bad pointer access
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc fixes from Helge Deller:
"On parisc we still sometimes need writeable stacks, e.g. if programs
aren't compiled with gcc-14. To avoid issues with the upcoming
systemd-254 we therefore have to disable prctl(PR_SET_MDWE) for now
(for parisc only).
The other two patches are minor: a bugfix for the soft power-off on
qemu with 64-bit kernel and prefer strscpy() over strlcpy():
- Fix power soft-off on qemu
- Disable prctl(PR_SET_MDWE) since parisc sometimes still needs
writeable stacks
- Use strscpy instead of strlcpy in show_cpuinfo()"
* tag 'parisc-for-6.7-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
prctl: Disable prctl(PR_SET_MDWE) on parisc
parisc/power: Fix power soft-off when running on qemu
parisc: Replace strlcpy() with strscpy()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- Various fixes for the DM delay target to address regressions
introduced during the 6.7 merge window
- Fixes to both DM bufio and the verity target for no-sleep mode,
to address sleeping while atomic issues
- Update DM crypt target in response to the treewide change that
made MAX_ORDER inclusive
* tag 'for-6.7/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm-crypt: start allocating with MAX_ORDER
dm-verity: don't use blocking calls from tasklets
dm-bufio: fix no-sleep mode
dm-delay: avoid duplicate logic
dm-delay: fix bugs introduced by kthread mode
dm-delay: fix a race between delay_presuspend and delay_bio
|
|
Firmware returns the physical address of the power switch,
so need to use gsc_writel() instead of direct memory access.
Fixes: d0c219472980 ("parisc/power: Add power soft-off when running on qemu")
Signed-off-by: Helge Deller <[email protected]>
Cc: [email protected] # v6.0+
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Revert a not-working conversion to generic recovery for PXA,
use proper IO accessors for designware, and use proper PM level
for ocores to allow accessing interrupt providers late"
* tag 'i2c-for-6.7-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: ocores: Move system PM hooks to the NOIRQ phase
i2c: designware: Fix corrupted memory seen in the ISR
Revert "i2c: pxa: move to generic GPIO recovery"
|
|
This NULL check was required when it was added, but we shuffled the code
around and now it's not. The inconsistent NULL checking triggers a
Smatch warning:
drivers/gpu/drm/msm/disp/mdp5/mdp5_kms.c:847 mdp5_init() warn:
variable dereferenced before check 'mdp5_kms' (see line 782)
Fixes: 1f50db2f3e1e ("drm/msm/mdp5: move resource allocation to the _probe function")
Signed-off-by: Dan Carpenter <[email protected]>
Reviewed-by: Uwe Kleine-König <[email protected]>
Reviewed-by: Dmitry Baryshkov <[email protected]>
Reviewed-by: Abhinav Kumar <[email protected]>
Patchwork: https://patchwork.freedesktop.org/patch/562559/
Link: https://lore.kernel.org/r/ZSj+6/J6YsoSpLak@kadam
Signed-off-by: Abhinav Kumar <[email protected]>
|
|
Pull drm fixes from Daniel Vetter:
"This is a 'blast from the bast' fixes pull, because it contains a
bunch of AGP fixes for amdgpu. Otherwise nothing out of the ordinary.
Next week is back to Dave unless he's knocked out by some conference
bug.
- amdgpu: fixes all over, including a set of AGP fixes
- nouvea: GSP + other bugfixes
- ivpu build fix
- lenovo legion go panel orientation quirk"
* tag 'drm-fixes-2023-11-17' of git://anongit.freedesktop.org/drm/drm: (30 commits)
drm/amdgpu/gmc9: disable AGP aperture
drm/amdgpu/gmc10: disable AGP aperture
drm/amdgpu/gmc11: disable AGP aperture
drm/amdgpu: add a module parameter to control the AGP aperture
drm/amdgpu/gmc11: fix logic typo in AGP check
drm/amd/display: Fix encoder disable logic
drm/amd/display: Change the DMCUB mailbox memory location from FB to inbox
drm/amdgpu: add and populate the port num into xgmi topology info
drm/amd/display: Negate IPS allow and commit bits
drm/amd/pm: Don't send unload message for reset
drm/amdgpu: fix ras err_data null pointer issue in amdgpu_ras.c
drm/amd/display: Clear dpcd_sink_ext_caps if not set
drm/amd/display: Enable fast plane updates on DCN3.2 and above
drm/amd/display: fix NULL dereference
drm/amd/display: fix a NULL pointer dereference in amdgpu_dm_i2c_xfer()
drm/amd/display: Add null checks for 8K60 lightup
drm/amd/pm: Fill pcie error counters for gpu v1_4
drm/amd/pm: Update metric table for smu v13_0_6
drm/amdgpu: correct chunk_ptr to a pointer to chunk.
drm/amd/display: Fix DSC not Enabled on Direct MST Sink
...
|
|
For "auo,b101uan08.3" this panel, it is stipulated in the panel spec that
MIPI needs to keep the LP11 state before the lcm_reset pin is pulled high.
Fixes: 56ad624b4cb5 ("drm/panel: support for auo, b101uan08.3 wuxga dsi video mode panel")
Signed-off-by: Xuxin Xiong <[email protected]>
Reviewed-by: Douglas Anderson <[email protected]>
Signed-off-by: Douglas Anderson <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/20231114044205.613421-1-xuxinxiong@huaqin.corp-partner.google.com
|
|
Commit 23baf831a32c ("mm, treewide: redefine MAX_ORDER sanely")
changed the meaning of MAX_ORDER from exclusive to inclusive. So, we
can allocate compound pages with up to 1 << MAX_ORDER pages.
Reflect this change in dm-crypt and start trying to allocate compound
pages with MAX_ORDER.
Signed-off-by: Mikulas Patocka <[email protected]>
Signed-off-by: Mike Snitzer <[email protected]>
|
|
The commit 5721d4e5a9cd enhanced dm-verity, so that it can verify blocks
from tasklets rather than from workqueues. This reportedly improves
performance significantly.
However, dm-verity was using the flag CRYPTO_TFM_REQ_MAY_SLEEP from
tasklets which resulted in warnings about sleeping function being called
from non-sleeping context.
BUG: sleeping function called from invalid context at crypto/internal.h:206
in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 14, name: ksoftirqd/0
preempt_count: 100, expected: 0
RCU nest depth: 0, expected: 0
CPU: 0 PID: 14 Comm: ksoftirqd/0 Tainted: G W 6.7.0-rc1 #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-2 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0x32/0x50
__might_resched+0x110/0x160
crypto_hash_walk_done+0x54/0xb0
shash_ahash_update+0x51/0x60
verity_hash_update.isra.0+0x4a/0x130 [dm_verity]
verity_verify_io+0x165/0x550 [dm_verity]
? free_unref_page+0xdf/0x170
? psi_group_change+0x113/0x390
verity_tasklet+0xd/0x70 [dm_verity]
tasklet_action_common.isra.0+0xb3/0xc0
__do_softirq+0xaf/0x1ec
? smpboot_thread_fn+0x1d/0x200
? sort_range+0x20/0x20
run_ksoftirqd+0x15/0x30
smpboot_thread_fn+0xed/0x200
kthread+0xdc/0x110
? kthread_complete_and_exit+0x20/0x20
ret_from_fork+0x28/0x40
? kthread_complete_and_exit+0x20/0x20
ret_from_fork_asm+0x11/0x20
</TASK>
This commit fixes dm-verity so that it doesn't use the flags
CRYPTO_TFM_REQ_MAY_SLEEP and CRYPTO_TFM_REQ_MAY_BACKLOG from tasklets. The
crypto API would do GFP_ATOMIC allocation instead, it could return -ENOMEM
and we catch -ENOMEM in verity_tasklet and requeue the request to the
workqueue.
Signed-off-by: Mikulas Patocka <[email protected]>
Cc: [email protected] # v6.0+
Fixes: 5721d4e5a9cd ("dm verity: Add optional "try_verify_in_tasklet" feature")
Signed-off-by: Mike Snitzer <[email protected]>
|
|
dm-bufio has a no-sleep mode. When activated (with the
DM_BUFIO_CLIENT_NO_SLEEP flag), the bufio client is read-only and we
could call dm_bufio_get from tasklets. This is used by dm-verity.
Unfortunately, commit 450e8dee51aa ("dm bufio: improve concurrent IO
performance") broke this and the kernel would warn that cache_get()
was calling down_read() from no-sleeping context. The bug can be
reproduced by using "veritysetup open" with the "--use-tasklets"
flag.
This commit fixes dm-bufio, so that the tasklet mode works again, by
expanding use of the 'no_sleep_enabled' static_key to conditionally
use either a rw_semaphore or rwlock_t (which are colocated in the
buffer_tree structure using a union).
Signed-off-by: Mikulas Patocka <[email protected]>
Cc: [email protected] # v6.4
Fixes: 450e8dee51aa ("dm bufio: improve concurrent IO performance")
Signed-off-by: Mike Snitzer <[email protected]>
|
|
This is small refactoring of dm-delay - we avoid duplicate logic in
flush_delayed_bios and flush_delayed_bios_fast and join these two
functions into one.
We also add cond_resched() to flush_delayed_bios because the list may have
unbounded number of entries.
Signed-off-by: Mikulas Patocka <[email protected]>
Signed-off-by: Mike Snitzer <[email protected]>
|
|
This commit fixes the following bugs introduced by commit 70bbeb29fab0
("dm delay: for short delays, use kthread instead of timers and wq"):
* the function flush_worker_fn has no exit path - on unload, this
function will just loop and consume 100% CPU without any progress
* the wake-up mechanism in flush_worker_fn is racy - a wake up will be
missed if the process adds entries to the delayed_bios list just
before set_current_state(TASK_INTERRUPTIBLE)
* flush_delayed_bios_fast submits a bio while holding a global mutex;
this may deadlock if we have multiple stacked dm-delay devices and
the underlying device attempts to acquire the mutex too
* if the target constructor fails, it will call delay_dtr. delay_dtr
would attempt to free dc->timer_lock without it being initialized by
the constructor.
* if the target constructor's kthread allocation fails, delay_dtr
would crash trying to dereference dc->worker because it is non-NULL
due to ERR_PTR.
Fixes: 70bbeb29fab0 ("dm delay: for short delays, use kthread instead of timers and wq")
Signed-off-by: Mikulas Patocka <[email protected]>
Signed-off-by: Mike Snitzer <[email protected]>
|
|
In delay_presuspend, we set the atomic variable may_delay and then stop
the timer and flush pending bios. The intention here is to prevent the
delay target from re-arming the timer again.
However, this test is racy. Suppose that one thread goes to delay_bio,
sees that dc->may_delay is one and proceeds; now, another thread executes
delay_presuspend, it sets dc->may_delay to zero, deletes the timer and
flushes pending bios. Then, the first thread continues and adds the bio to
delayed->list despite the fact that dc->may_delay is false.
Fix this bug by changing may_delay's type from atomic_t to bool and
only access it while holding the delayed_bios_lock mutex. Note that we
don't have to grab the mutex in delay_resume because there are no bios
in flight at this point.
Signed-off-by: Mikulas Patocka <[email protected]>
Cc: [email protected]
Signed-off-by: Mike Snitzer <[email protected]>
|
|
When pairing DP IN and DP OUT adapters for DisplayPort tunneling, we
should prioritize the possible external GPU DP IN adapters to take
advantage of the its capabilities. However the commit in question did
this for host router DP IN adapters too and that changes ordering of the
initial DP IN resources in such way that resuming from suspend may end
up using different resource and that may confuse the user.
Fix this so that we only put DP IN adapters of device routers to the top
of the resource list and leave host routers as is.
Fixes: 274baf695b08 ("thunderbolt: Add DP IN added last in the head of the list of DP resources")
Reported-by: Pengfei Xu <[email protected]>
Signed-off-by: Mika Westerberg <[email protected]>
|
|
We should send uevent to userspace whenever the link speed or width
changes but tb_switch_asym_enable() and tb_switch_asym_disable() set the
sw->link_width already so tb_switch_update_link_attributes() never
noticed the change.
Fix this so that we let tb_switch_update_link_attributes() update the
fields accordingly.
Fixes: 81af2952e606 ("thunderbolt: Add support for asymmetric link")
Reported-by: Pengfei Xu <[email protected]>
Tested-by: Pengfei Xu <[email protected]>
Signed-off-by: Mika Westerberg <[email protected]>
|
|
Fix the lane bonding procedure to follow the steps described in USB4
Connection Manager guide. Hence, set the lane bonding bit only for
downstream port. This is needed for certain ASMedia device, otherwise
lane bonding fails and the device disconnects.
Cc: [email protected]
Signed-off-by: Gil Fine <[email protected]>
Signed-off-by: Mika Westerberg <[email protected]>
|
|
https://gitlab.freedesktop.org/agd5f/linux into drm-fixes
amd-drm-fixes-6.7-2023-11-17:
amdgpu:
- DMCUB fixes
- SR-IOV fix
- GMC9 fix
- Documentation fix
- DSC MST fix
- CS chunk parsing fix
- SMU13.0.6 fixes
- 8K tiled display fix
- Fix potential NULL pointer dereferences
- Cursor lag fix
- Backlight fix
- DCN s0ix fix
- XGMI fix
- DCN encoder disable logic fix
- AGP aperture fixes
Signed-off-by: Daniel Vetter <[email protected]>
From: Alex Deucher <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
amd_pmc_get_dram_size() is used to get the DRAM size information. But
in the current code, mailbox command to get the DRAM size info is sent
based on the values of dev->major and dev->minor.
But dev->major and dev->minor will have either junk or zero assigned to
them until at least once a call to amd_pmc_get_smu_version() is made
which ideally populates dev->major and dev->minor.
However, adding a amd_pmc_get_smu_version() call to
amd_pmc_get_dram_size() has a downside of elevating the boot times.
After talking to the PMFW team, it's understood that the "get dram
size" mbox command would only be supported on specific platforms (like
Mendocino) and not all. So, adjust getting DRAM size behavior such
that,
- if running on Rembrandt or Mendocino and the underlying PMFW knows
how to execute the "get dram size" command it shall give the custom
dram size.
- if the underlying FW does not report the dram size, we just proceed
further and assign the default dram size.
The simplest way to address this is to remove amd_pmc_get_dram_size()
function and directly call the "get dram size" command in the
amd_pmc_s2d_init().
Reported-by: Mark Hasemeyer <[email protected]>
Fixes: be8325fb3d8c ("platform/x86/amd: pmc: Get STB DRAM size from PMFW")
Cc: [email protected]
Suggested-by: Sanket Goswami <[email protected]>
Signed-off-by: Shyam Sundar S K <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Reviewed-by: Mario Limonciello <[email protected]>
Reviewed-by: Ilpo Järvinen <[email protected]>
Signed-off-by: Ilpo Järvinen <[email protected]>
|
|
__counted_by
Fake flexible arrays (zero-length and one-element arrays) are deprecated,
and should be replaced by flexible-array members. So, replace
zero-length array with a flexible-array member in `struct
privcmd_kernel_ioreq`.
Also annotate array `ports` with `__counted_by()` to prepare for the
coming implementation by GCC and Clang of the `__counted_by` attribute.
Flexible array members annotated with `__counted_by` can have their
accesses bounds-checked at run-time via `CONFIG_UBSAN_BOUNDS` (for array
indexing) and `CONFIG_FORTIFY_SOURCE` (for strcpy/memcpy-family functions).
This fixes multiple -Warray-bounds warnings:
drivers/xen/privcmd.c:1239:30: warning: array subscript i is outside array bounds of 'struct ioreq_port[0]' [-Warray-bounds=]
drivers/xen/privcmd.c:1240:30: warning: array subscript i is outside array bounds of 'struct ioreq_port[0]' [-Warray-bounds=]
drivers/xen/privcmd.c:1241:30: warning: array subscript i is outside array bounds of 'struct ioreq_port[0]' [-Warray-bounds=]
drivers/xen/privcmd.c:1245:33: warning: array subscript i is outside array bounds of 'struct ioreq_port[0]' [-Warray-bounds=]
drivers/xen/privcmd.c:1258:67: warning: array subscript i is outside array bounds of 'struct ioreq_port[0]' [-Warray-bounds=]
This results in no differences in binary output.
Signed-off-by: Gustavo A. R. Silva <[email protected]>
Reviewed-by: Kees Cook <[email protected]>
Reviewed-by: Juergen Gross <[email protected]>
Link: https://lore.kernel.org/r/ZVZlg3tPMPCRdteh@work
Signed-off-by: Juergen Gross <[email protected]>
|
|
There's a bug that when using the XEN hypervisor with bios with large
multi-page bio vectors on NVMe, the kernel deadlocks [1].
The deadlocks are caused by inability to map a large bio vector -
dma_map_sgtable always returns an error, this gets propagated to the block
layer as BLK_STS_RESOURCE and the block layer retries the request
indefinitely.
XEN uses the swiotlb framework to map discontiguous pages into contiguous
runs that are submitted to the PCIe device. The swiotlb framework has a
limitation on the length of a mapping - this needs to be announced with
the max_mapping_size method to make sure that the hardware drivers do not
create larger mappings.
Without max_mapping_size, the NVMe block driver would create large
mappings that overrun the maximum mapping size.
Reported-by: Marek Marczykowski-Górecki <[email protected]>
Link: https://lore.kernel.org/stable/ZTNH0qtmint%2FzLJZ@mail-itl/ [1]
Tested-by: Marek Marczykowski-Górecki <[email protected]>
Suggested-by: Christoph Hellwig <[email protected]>
Cc: [email protected]
Signed-off-by: Keith Busch <[email protected]>
Signed-off-by: Mikulas Patocka <[email protected]>
Acked-by: Stefano Stabellini <[email protected]>
Reviewed-by: Christoph Hellwig <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Juergen Gross <[email protected]>
|
|
We've had misc reports of random IOMMU page faults when
this is used. It's just a rarely used optimization anyway, so
let's just disable it. It can still be toggled via the
module parameter for testing.
v2: leave it configurable via module parameter
Reviewed-by: Yang Wang <[email protected]> (v1)
Acked-by: Christian König <[email protected]>
Reviewed-by: Mario Limonciello <[email protected]>
Tested-by: Mario Limonciello <[email protected]> # PHX & Navi33
Signed-off-by: Alex Deucher <[email protected]>
|
|
We've had misc reports of random IOMMU page faults when
this is used. It's just a rarely used optimization anyway, so
let's just disable it. It can still be toggled via the
module parameter for testing.
v2: leave it configurable via module parameter
Reviewed-by: Yang Wang <[email protected]> (v1)
Acked-by: Christian König <[email protected]>
Reviewed-by: Mario Limonciello <[email protected]>
Tested-by: Mario Limonciello <[email protected]> # PHX & Navi33
Signed-off-by: Alex Deucher <[email protected]>
|
|
We've had misc reports of random IOMMU page faults when
this is used. It's just a rarely used optimization anyway, so
let's just disable it. It can still be toggled via the
module parameter for testing.
v2: leave it configurable via module parameter
Fixes: 67318cb84341 ("drm/amdgpu/gmc11: set gart placement GC11")
Reviewed-by: Yang Wang <[email protected]> (v1)
Acked-by: Christian König <[email protected]>
Reviewed-by: Mario Limonciello <[email protected]>
Tested-by: Mario Limonciello <[email protected]> # PHX & Navi33
Signed-off-by: Alex Deucher <[email protected]>
|
|
Add a module parameter to control the AGP aperture. The AGP
aperture is an aperture in the GPU's internal address space
which provides direct non-paged access to the platform address
space. This access is non-snooped so only uncached memory
can be accessed.
Add a knob so that we can toggle this for debugging.
Fixes: 67318cb84341 ("drm/amdgpu/gmc11: set gart placement GC11")
Acked-by: Christian König <[email protected]>
Reviewed-by: Mario Limonciello <[email protected]>
Tested-by: Mario Limonciello <[email protected]> # PHX & Navi33
Signed-off-by: Alex Deucher <[email protected]>
|
|
Should be && rather than ||.
Fixes: b2e1cbe6281f ("drm/amdgpu/gmc11: disable AGP on GC 11.5")
Acked-by: Christian König <[email protected]>
Reviewed-by: Mario Limonciello <[email protected]>
Tested-by: Mario Limonciello <[email protected]> # PHX & Navi33
Signed-off-by: Alex Deucher <[email protected]>
|