| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
SanDisks USB3 storage may disapper after system reboot:
usb usb2-port3: link state change
xhci_hcd 0000:00:14.0: clear port3 link state change, portsc: 0x2c0
usb usb2-port3: do warm reset, port only
xhci_hcd 0000:00:14.0: xhci_hub_status_data: stopping usb2 port polling
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x2b0, return 0x2b0
usb usb2-port3: not warm reset yet, waiting 50ms
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x2f0, return 0x2f0
usb usb2-port3: not warm reset yet, waiting 200ms
...
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x6802c0, return 0x7002c0
usb usb2-port3: not warm reset yet, waiting 200ms
xhci_hcd 0000:00:14.0: clear port3 reset change, portsc: 0x4802c0
xhci_hcd 0000:00:14.0: clear port3 warm(BH) reset change, portsc: 0x4002c0
xhci_hcd 0000:00:14.0: clear port3 link state change, portsc: 0x2c0
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x2c0, return 0x2c0
usb usb2-port3: not enabled, trying warm reset again...
This is due to the USB device still cause port change event after xHCI is
shuted down:
xhci_hcd 0000:38:00.0: // Setting command ring address to 0xffffe001
xhci_hcd 0000:38:00.0: xhci_resume: starting usb3 port polling.
xhci_hcd 0000:38:00.0: xhci_hub_status_data: stopping usb4 port polling
xhci_hcd 0000:38:00.0: xhci_hub_status_data: stopping usb3 port polling
xhci_hcd 0000:38:00.0: hcd_pci_runtime_resume: 0
xhci_hcd 0000:38:00.0: xhci_shutdown: stopping usb3 port polling.
xhci_hcd 0000:38:00.0: // Halt the HC
xhci_hcd 0000:38:00.0: xhci_shutdown completed - status = 1
xhci_hcd 0000:00:14.0: xhci_shutdown: stopping usb1 port polling.
xhci_hcd 0000:00:14.0: // Halt the HC
xhci_hcd 0000:00:14.0: xhci_shutdown completed - status = 1
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x1203, return 0x203
xhci_hcd 0000:00:14.0: set port reset, actual port 2-3 status = 0x1311
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x201203, return 0x100203
xhci_hcd 0000:00:14.0: clear port3 reset change, portsc: 0x1203
xhci_hcd 0000:00:14.0: clear port3 warm(BH) reset change, portsc: 0x1203
xhci_hcd 0000:00:14.0: clear port3 link state change, portsc: 0x1203
xhci_hcd 0000:00:14.0: clear port3 connect change, portsc: 0x1203
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x1203, return 0x203
usb 2-3: device not accepting address 2, error -108
xhci_hcd 0000:00:14.0: xHCI dying or halted, can't queue_command
xhci_hcd 0000:00:14.0: Set port 2-3 link state, portsc: 0x1203, write 0x11261
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x1263, return 0x263
xhci_hcd 0000:00:14.0: set port reset, actual port 2-3 status = 0x1271
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x12b1, return 0x2b1
usb usb2-port3: not reset yet, waiting 60ms
ACPI: PM: Preparing to enter system sleep state S5
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x12f1, return 0x2f1
usb usb2-port3: not reset yet, waiting 200ms
reboot: Restarting system
The port change event is caused by LPM transition, so disabling LPM at shutdown
to make sure the device is in U0 for warmboot.
Signed-off-by: Kai-Heng Feng <[email protected]>
Cc: stable <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
When ncm function is working and then stop usb0 interface for link down,
eth_stop() is called. At this piont, accidentally if usb transport error
should happen in usb_ep_enable(), 'in_ep' and/or 'out_ep' may not be enabled.
After that, ncm_disable() is called to disable for ncm unbind
but gether_disconnect() is never called since 'in_ep' is not enabled.
As the result, ncm object is released in ncm unbind
but 'dev->port_usb' associated to 'ncm->port' is not NULL.
And when ncm bind again to recover netdev, ncm object is reallocated
but usb0 interface is already associated to previous released ncm object.
Therefore, once usb0 interface is up and eth_start_xmit() is called,
released ncm object is dereferrenced and it might cause use-after-free memory.
[function unlink via configfs]
usb0: eth_stop dev->port_usb=ffffff9b179c3200
--> error happens in usb_ep_enable().
NCM: ncm_disable: ncm=ffffff9b179c3200
--> no gether_disconnect() since ncm->port.in_ep->enabled is false.
NCM: ncm_unbind: ncm unbind ncm=ffffff9b179c3200
NCM: ncm_free: ncm free ncm=ffffff9b179c3200 <-- released ncm
[function link via configfs]
NCM: ncm_alloc: ncm alloc ncm=ffffff9ac4f8a000
NCM: ncm_bind: ncm bind ncm=ffffff9ac4f8a000
NCM: ncm_set_alt: ncm=ffffff9ac4f8a000 alt=0
usb0: eth_open dev->port_usb=ffffff9b179c3200 <-- previous released ncm
usb0: eth_start dev->port_usb=ffffff9b179c3200 <--
eth_start_xmit()
--> dev->wrap()
Unable to handle kernel paging request at virtual address dead00000000014f
This patch addresses the issue by checking if 'ncm->netdev' is not NULL at
ncm_disable() to call gether_disconnect() to deassociate 'dev->port_usb'.
It's more reasonable to check 'ncm->netdev' to call gether_connect/disconnect
rather than check 'ncm->port.in_ep->enabled' since it might not be enabled
but the gether connection might be established.
Signed-off-by: Norihiko Hama <[email protected]>
Cc: stable <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Off-by-one errors happen because nr_snk_pdo and nr_src_pdo are
incorrectly added one. The index of the loop is equal to the number of
PDOs to be updated when leaving the loop and it doesn't need to be added
one.
When doing the power negotiation, TCPM relies on the "nr_snk_pdo" as
the size of the local sink PDO array to match the Source capabilities
of the partner port. If the off-by-one overflow occurs, a wrong RDO
might be sent and unexpected power transfer might happen such as over
voltage or over current (than expected).
"nr_src_pdo" is used to set the Rp level when the port is in Source
role. It is also the array size of the local Source capabilities when
filling up the buffer which will be sent as the Source PDOs (such as
in Power Negotiation). If the off-by-one overflow occurs, a wrong Rp
level might be set and wrong Source PDOs will be sent to the partner
port. This could potentially cause over current or port resets.
Fixes: cd099cde4ed2 ("usb: typec: tcpm: Support multiple capabilities")
Cc: [email protected]
Signed-off-by: Kyle Tso <[email protected]>
Reviewed-by: Heikki Krogerus <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Instead of bailing when fences have already been installed on the
DMABUF, wait for them (with a timeout) when doing a blocking operation.
This fixes the issue where userspace would submit a DMABUF with fences
already installed, with the (correct) expectation that it would just
work.
Fixes: 7b07a2a7ca02 ("usb: gadget: functionfs: Add DMABUF import interface")
Signed-off-by: Paul Cercueil <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
A "read" fence was installed when the DMABUF was to be written to,
and a "write" fence was installed when the DMABUF was to be read from.
Besides, dma_resv_usage_rw() should only be used when waiting for
fences.
Fixes: 7b07a2a7ca02 ("usb: gadget: functionfs: Add DMABUF import interface")
Signed-off-by: Paul Cercueil <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Fix issues when initially checking for a connector change:
- Use the correct connector number not the entire CCI.
- Call ->read under the PPM lock.
- Remove a bogus READ_ONCE.
Fixes: 808a8b9e0b87 ("usb: typec: ucsi: Check for notifications after init")
Cc: [email protected]
Signed-off-by: Christian A. Ehrhardt <[email protected]>
Reviewed-by: Heikki Krogerus <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The pointer from a xhci usb virt device to its root hub port
(vdev->rhub_port) is set later when device is addressed, not while
vdev is allocated.
Tracepoints dereferenced this rhub_port pointer when freeing the virt
device, which causes null pointer dereference if tracing is enabled
and device is freed before addressed.
This can happen if tracing is enabled and xhci driver is unloaded before
a device is fully enumerated, or initial enumeration fails and device
is reset and freed before retry.
Don't dereference the rhub_port or show port numbers when tracing
xhci_free_virt_device(). This info is not very useful anyway.
Print the more useful slot id instead
Fixes: 06790c19086f ("xhci: replace real & fake port with pointer to root hub port")
Reported-by: Thinh Nguyen <[email protected]>
Closes: https://lore.kernel.org/linux-usb/[email protected]/
Signed-off-by: Mathias Nyman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
If we get STS_HCE we give up on the interrupt, but for the purpose
of IRQ handling that still counts as ours. We may return IRQ_NONE
only if we are positive that it wasn't ours. Hence correct the default.
Fixes: 2a25e66d676d ("xhci: print warning when HCE was set")
Cc: [email protected] # v6.2+
Signed-off-by: Oliver Neukum <[email protected]>
Signed-off-by: Mathias Nyman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
We need the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The XMOS XVF3500 VocalFusion Voice Processor[1] is a low-latency, 32-bit
multicore controller for voice processing.
This device requires a specific power sequence, which consists of
enabling the regulators that control the 3V3 and 1V0 device supplies,
and a reset de-assertion after a delay of at least 100ns.
Once in normal operation, the XVF3500 registers itself as a USB device,
and it does not require any device-specific operations in the driver.
[1] https://www.xmos.com/xvf3500/
Acked-by: Matthias Kaehlcke <[email protected]>
Signed-off-by: Javier Carrasco <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Most of the functionality this driver provides can be used by non-hub
devices as well.
To account for the hub-specific code, add a flag to the device data
structure and check its value for hub-specific code.
The 'always_powered_in_supend' attribute is only available for hub
devices, keeping the driver's default behavior for non-hub devices (keep
on in suspend).
Acked-by: Matthias Kaehlcke <[email protected]>
Signed-off-by: Javier Carrasco <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
This patch prepares onboad_hub to support non-hub devices by renaming
the driver files and their content, the headers and their references.
The comments and descriptions have been slightly modified to keep
coherence and account for the specific cases that only affect onboard
hubs (e.g. peer-hub).
The "hub" variables in functions where "dev" (and similar names) variables
already exist have been renamed to onboard_dev for clarity, which adds a
few lines in cases where more than 80 characters are used.
No new functionality has been added.
Acked-by: Matthias Kaehlcke <[email protected]>
Signed-off-by: Javier Carrasco <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The current implementation uses generic names for the power supplies,
which conflicts with proper name definitions in the device bindings.
Add a per-device property to include real supply names and keep generic
names for existing devices to keep backward compatibility.
Acked-by: Matthias Kaehlcke <[email protected]>
Signed-off-by: Javier Carrasco <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The dt-bindings is going to use "usb_wakeup" as wakup clock name. This will
align the change with dt-bindings.
Acked-by: Peter Chen <[email protected]>
Signed-off-by: Xu Yang <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Remove the trailing comma in the terminator entry for the OF table
making code robust against (theoretical) misrebases or other similar
things where the new entry goes _after_ the termination without the
compiler noticing.
Signed-off-by: Biju Das <[email protected]>
Reviewed-by: Geert Uytterhoeven <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The RZ/G2L family SoCs has 10 pipe buffers compared to 16 pipe buffers on
RZ/A2M. Update the pipe configuration for RZ/G2L family SoCs and use
family SoC specific compatible to handle this difference.
The pipe configuration of RZ/G2L is same as usbhsc_rzg2l_default_pipe[],
so select the default pipe configuration for RZ/G2L SoCs by setting
.has_new_pipe_configs to zero.
Add SoC specific compatible to OF table to avoid ABI breakage with old
DTB. To optimize memory usage the SoC specific compatible will be removed
later.
Based on the patch in BSP by Huy Nguyen <[email protected]>
Signed-off-by: Biju Das <[email protected]>
Reviewed-by: Geert Uytterhoeven <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
As per the hardware manual, double buffer setting results in fewer
interrupts for high-speed data transfers. Improve usbhsc_default_pipe[]
for isochronous transfers by updating the table from single->double
buffering and update the pipe number accordingly.
Suggested-by: Geert Uytterhoeven <[email protected]>
Signed-off-by: Biju Das <[email protected]>
Reviewed-by: Geert Uytterhoeven <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Simplify probe() by removing redundant dev->of_node check.
While at it, replace dev_err->dev_err_probe for error path.
Signed-off-by: Biju Das <[email protected]>
Reviewed-by: Geert Uytterhoeven <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Add params for DWC2 IP in Sophgo CV18XX/SG200X series SoC.
Signed-off-by: Inochi Amaoto <[email protected]>
Acked-by: Minas Harutyunyan <[email protected]>
Link: https://lore.kernel.org/r/IA1PR20MB4953EE73DD36D5FFC81D90EDBB352@IA1PR20MB4953.namprd20.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The show and store callback routines for the "disable" sysfs attribute
file in port.c acquire the device lock for the port's parent hub
device. This can cause problems if another process has locked the hub
to remove it or change its configuration:
Removing the hub or changing its configuration requires the
hub interface to be removed, which requires the port device
to be removed, and device_del() waits until all outstanding
sysfs attribute callbacks for the ports have returned. The
lock can't be released until then.
But the disable_show() or disable_store() routine can't return
until after it has acquired the lock.
The resulting deadlock can be avoided by calling
sysfs_break_active_protection(). This will cause the sysfs core not
to wait for the attribute's callback routine to return, allowing the
removal to proceed. The disadvantage is that after making this call,
there is no guarantee that the hub structure won't be deallocated at
any moment. To prevent this, we have to acquire a reference to it
first by calling hub_get().
Signed-off-by: Alan Stern <[email protected]>
Cc: stable <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Create hub_get() and hub_put() routines to encapsulate the kref_get()
and kref_put() calls in hub.c. The new routines will be used by the
next patch in this series.
Signed-off-by: Alan Stern <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Cc: stable <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Check the UCSI_CAP_GET_PD_MESSAGE bit before sending GET_PD_MESSAGE to
discover partner and cable identity, check UCSI_CAP_CABLE_DETAILS before
sending GET_CABLE_PROPERTY to discover the cable and check
UCSI_CAP_ALT_MODE_DETAILS before registering the a cable plug. Additionally,
move 8 bits from reserved_1 to features in the ucsi_capability struct. This
makes the field 16 bits, still 8 short of the 24 bits allocated for it in
UCSI v3.0, but it will not overflow because UCSI only defines 14 bits in
bmOptionalFeatures.
Fixes: 38ca416597b0 ("usb: typec: ucsi: Register cables based on GET_CABLE_PROPERTY")
Link: https://lore.kernel.org/linux-usb/[email protected]
Suggested-by: Neil Armstrong <[email protected]>
Signed-off-by: Jameson Thies <[email protected]>
Tested-by: Neil Armstrong <[email protected]> # on SM8550-QRD
Reviewed-by: Benson Leung <[email protected]>
Reviewed-by: Neil Armstrong <[email protected]>
Reviewed-by: Heikki Krogerus <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Check the UCSI_CCI_RESET_COMPLETE complete flag before starting
another reset. Use a UCSI_SET_NOTIFICATION_ENABLE command to clear
the flag if it is set.
Signed-off-by: Christian A. Ehrhardt <[email protected]>
Cc: stable <[email protected]>
Reviewed-by: Heikki Krogerus <[email protected]>
Tested-by: Neil Armstrong <[email protected]> # on SM8550-QRD
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Some DELL systems don't like UCSI_ACK_CC_CI commands with the
UCSI_ACK_CONNECTOR_CHANGE but not the UCSI_ACK_COMMAND_COMPLETE
bit set. The current quirk still leaves room for races because
it requires two consecutive ACK commands to be sent.
Refactor and significantly simplify the quirk to fix this:
Send a dummy command and bundle the connector change ack with the
command completion ack in a single UCSI_ACK_CC_CI command.
This removes the need to probe for the quirk.
While there define flag bits for struct ucsi_acpi->flags in ucsi_acpi.c
and don't re-use definitions from ucsi.h for struct ucsi->flags.
Fixes: f3be347ea42d ("usb: ucsi_acpi: Quirk to ack a connector change ack cmd")
Cc: [email protected]
Signed-off-by: Christian A. Ehrhardt <[email protected]>
Reviewed-by: Heikki Krogerus <[email protected]>
Tested-by: Neil Armstrong <[email protected]> # on SM8550-QRD
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
If a command completes the OPM must send an ack. This applies
to unsupported commands, too.
Send the required ACK for unsupported commands.
Signed-off-by: Christian A. Ehrhardt <[email protected]>
Cc: stable <[email protected]>
Reviewed-by: Heikki Krogerus <[email protected]>
Tested-by: Neil Armstrong <[email protected]> # on SM8550-QRD
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The completion notification for the final SET_NOTIFICATION_ENABLE
command during initialization can include a connector change
notification. However, at the time this completion notification is
processed, the ucsi struct is not ready to handle this notification.
As a result the notification is ignored and the controller
never sends an interrupt again.
Re-check CCI for a pending connector state change after
initialization is complete. Adjust the corresponding debug
message accordingly.
Fixes: 71a1fa0df2a3 ("usb: typec: ucsi: Store the notification mask")
Cc: [email protected]
Signed-off-by: Christian A. Ehrhardt <[email protected]>
Reviewed-by: Heikki Krogerus <[email protected]>
Tested-by: Neil Armstrong <[email protected]> # on SM8550-QRD
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Suppose we sleep on the PPM lock after clearing the EVENT_PENDING
bit because the thread for another connector is executing a command.
In this case the command completion of the other command will still
report the connector change for our connector.
Clear the EVENT_PENDING bit under the PPM lock to avoid another
useless call to ucsi_handle_connector_change() in this case.
Fixes: c9aed03a0a68 ("usb: ucsi: Add missing ppm_lock")
Cc: stable <[email protected]>
Signed-off-by: Christian A. Ehrhardt <[email protected]>
Reviewed-by: Heikki Krogerus <[email protected]>
Tested-by: Neil Armstrong <[email protected]> # on SM8550-QRD
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The attribute writing should return the number of bytes used from the
buffer on success.
Fixes: a7cff92f0635 ("usb: typec: USB Power Delivery helpers for ports and partners")
Cc: [email protected]
Signed-off-by: Kyle Tso <[email protected]>
Reviewed-by: Guenter Roeck <[email protected]>
Reviewed-by: Heikki Krogerus <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
It is possible trigger below warning message from mass storage function,
WARNING: CPU: 6 PID: 3839 at drivers/usb/gadget/udc/core.c:294 usb_ep_queue+0x7c/0x104
pc : usb_ep_queue+0x7c/0x104
lr : fsg_main_thread+0x494/0x1b3c
Root cause is mass storage function try to queue request from main thread,
but other thread may already disable ep when function disable.
As there is no function failure in the driver, in order to avoid effort
to fix warning, change WARN_ON_ONCE() in usb_ep_queue() to pr_debug().
Suggested-by: Alan Stern <[email protected]>
Cc: [email protected]
Signed-off-by: yuan linyu <[email protected]>
Reviewed-by: Alan Stern <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Intel Arrow Lake CPU uses the Meteor Lake ID with this
controller (the controller that's part of the Intel Arrow
Lake chipset (PCH) does still have unique PCI ID).
Fixes: de4b5b28c87c ("usb: dwc3: pci: add support for the Intel Arrow Lake-H")
Signed-off-by: Heikki Krogerus <[email protected]>
Acked-by: Thinh Nguyen <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
If the device is configured for system wakeup, then make sure that the
xHCI driver knows about it and make sure to permit wakeup only at the
appropriate time.
For host mode, if the controller goes through the dwc3 code path, then a
child xHCI platform device is created. Make sure the platform device
also inherits the wakeup setting for xHCI to enable remote wakeup.
For device mode, make sure to disable system wakeup if no gadget driver
is bound. We may experience unwanted system wakeup due to the wakeup
signal from the controller PMU detecting connection/disconnection when
in low power (D3). E.g. In the case of Steam Deck, the PCI PME prevents
the system staying in suspend.
Cc: [email protected]
Reported-by: Guilherme G. Piccoli <[email protected]>
Closes: https://lore.kernel.org/linux-usb/[email protected]/T/#mf00d6669c2eff7b308d1162acd1d66c09f0853c7
Fixes: d07e8819a03d ("usb: dwc3: add xHCI Host support")
Signed-off-by: Thinh Nguyen <[email protected]>
Tested-by: Sanath S <[email protected]>
Tested-by: Guilherme G. Piccoli <[email protected]> # Steam Deck
Link: https://lore.kernel.org/r/667cfda7009b502e08462c8fb3f65841d103cc0a.1709865476.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
This reverts commit 75fd6485cccef269ac9eb3b71cf56753341195ef.
This patch was applied twice by accident, causing probe failures.
Revert the accident.
Signed-off-by: Alexander Stein <[email protected]>
Fixes: 75fd6485ccce ("usb: phy: generic: Get the vbus supply")
Cc: stable <[email protected]>
Reviewed-by: Sean Anderson <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
wdm_read() cannot race with itself. However, in
service_outstanding_interrupt() it can race with the
workqueue, which can be triggered by error handling.
Hence we need to make sure that the WDM_RESPONDING
flag is not just only set but tested.
Fixes: afba937e540c9 ("USB: CDC WDM driver")
Cc: stable <[email protected]>
Signed-off-by: Oliver Neukum <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Added functionality to exit from L1 state by device initiation
using remote wakeup signaling, in case when function driver queuing
request while core in L1 state.
Fixes: 273d576c4d41 ("usb: dwc2: gadget: Add functionality to exit from LPM L1 state")
Fixes: 88b02f2cb1e1 ("usb: dwc2: Add core state checking")
CC: [email protected]
Signed-off-by: Minas Harutyunyan <[email protected]>
Link: https://lore.kernel.org/r/b4d9de5382375dddbf7ef6049d9a82066ad87d5d.1710166393.git.Minas.Harutyunyan@synopsys.com
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Added exiting from the clock gating mode on USB Reset Detect interrupt
if core in the clock gating mode.
Added new condition to check core in clock gating mode or no.
Fixes: 9b4965d77e11 ("usb: dwc2: Add exit clock gating from session request interrupt")
Fixes: 5d240efddc7f ("usb: dwc2: Add exit clock gating from wakeup interrupt")
Fixes: 16c729f90bdf ("usb: dwc2: Allow exit clock gating in urb enqueue")
Fixes: 401411bbc4e6 ("usb: dwc2: Add exit clock gating before removing driver")
CC: [email protected]
Signed-off-by: Minas Harutyunyan <[email protected]>
Link: https://lore.kernel.org/r/cbcc2ccd37e89e339130797ed68ae4597db773ac.1708938774.git.Minas.Harutyunyan@synopsys.com
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Fixed ISOC completion flow in DDMA mode. Added isoc
descriptor actual length value and update urb's start_frame
value.
Fixed initialization of ISOC DMA descriptors flow.
Fixes: 56f5b1cff22a ("staging: Core files for the DWC2 driver")
Fixes: 20f2eb9c4cf8 ("staging: dwc2: add microframe scheduler from downstream Pi kernel")
Fixes: c17b337c1ea4 ("usb: dwc2: host: program descriptor for next frame")
Fixes: dc4c76e7b22c ("staging: HCD descriptor DMA support for the DWC2 driver")
Fixes: 762d3a1a9cd7 ("usb: dwc2: host: process all completed urbs")
CC: [email protected]
Signed-off-by: Minas Harutyunyan <[email protected]>
Link: https://lore.kernel.org/r/a8b1e1711cc6cabfb45d92ede12e35445c66f06c.1708944698.git.Minas.Harutyunyan@synopsys.com
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Starting from core v4.30a changed order of programming
GPWRDN_PMUACTV to 0 in case of exit from hibernation on
remote wakeup signaling from device.
Fixes: c5c403dc4336 ("usb: dwc2: Add host/device hibernation functions")
CC: [email protected]
Signed-off-by: Minas Harutyunyan <[email protected]>
Link: https://lore.kernel.org/r/99385ec55ce73445b6fbd0f471c9bd40eb1c9b9e.1708939799.git.Minas.Harutyunyan@synopsys.com
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Added to backup/restore registers HFLBADDR, HCCHARi, HCSPLTi,
HCTSIZi, HCDMAi and HCDMABi.
Fixes: 58e52ff6a6c3 ("usb: dwc2: Move register save and restore functions")
Fixes: d17ee77b3044 ("usb: dwc2: add controller hibernation support")
CC: [email protected]
Signed-off-by: Minas Harutyunyan <[email protected]>
Link: https://lore.kernel.org/r/c2d10ee6098b9b009a8e94191e046004747d3bdd.1708945444.git.Minas.Harutyunyan@synopsys.com
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Among the attribute file callback routines in
drivers/usb/core/sysfs.c, the interface_authorized_store() function is
the only one which acquires a device lock on an ancestor device: It
calls usb_deauthorize_interface(), which locks the interface's parent
USB device.
The will lead to deadlock if another process already owns that lock
and tries to remove the interface, whether through a configuration
change or because the device has been disconnected. As part of the
removal procedure, device_del() waits for all ongoing sysfs attribute
callbacks to complete. But usb_deauthorize_interface() can't complete
until the device lock has been released, and the lock won't be
released until the removal has finished.
The mechanism provided by sysfs to prevent this kind of deadlock is
to use the sysfs_break_active_protection() function, which tells sysfs
not to wait for the attribute callback.
Reported-and-tested by: Yue Sun <[email protected]>
Reported by: xingwei lee <[email protected]>
Signed-off-by: Alan Stern <[email protected]>
Link: https://lore.kernel.org/linux-usb/CAEkJfYO6jRVC8Tfrd_R=cjO0hguhrV31fDPrLrNOOHocDkPoAA@mail.gmail.com/#r
Fixes: 310d2b4124c0 ("usb: interface authorization: SysFS part of USB interface authorization")
Cc: [email protected]
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The PD of Type-C port needs to be updated in pd_set. Unlink the Type-C
port device to the old PD before linking it to a new one.
Fixes: cd099cde4ed2 ("usb: typec: tcpm: Support multiple capabilities")
Cc: [email protected]
Signed-off-by: Kyle Tso <[email protected]>
Acked-by: Heikki Krogerus <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
When unregister pd capabilitie in tcpm, KASAN will capture below double
-free issue. The root cause is the same capabilitiy will be kfreed twice,
the first time is kfreed by pd_capabilities_release() and the second time
is explicitly kfreed by tcpm_port_unregister_pd().
[ 3.988059] BUG: KASAN: double-free in tcpm_port_unregister_pd+0x1a4/0x3dc
[ 3.995001] Free of addr ffff0008164d3000 by task kworker/u16:0/10
[ 4.001206]
[ 4.002712] CPU: 2 PID: 10 Comm: kworker/u16:0 Not tainted 6.8.0-rc5-next-20240220-05616-g52728c567a55 #53
[ 4.012402] Hardware name: Freescale i.MX8QXP MEK (DT)
[ 4.017569] Workqueue: events_unbound deferred_probe_work_func
[ 4.023456] Call trace:
[ 4.025920] dump_backtrace+0x94/0xec
[ 4.029629] show_stack+0x18/0x24
[ 4.032974] dump_stack_lvl+0x78/0x90
[ 4.036675] print_report+0xfc/0x5c0
[ 4.040289] kasan_report_invalid_free+0xa0/0xc0
[ 4.044937] __kasan_slab_free+0x124/0x154
[ 4.049072] kfree+0xb4/0x1e8
[ 4.052069] tcpm_port_unregister_pd+0x1a4/0x3dc
[ 4.056725] tcpm_register_port+0x1dd0/0x2558
[ 4.061121] tcpci_register_port+0x420/0x71c
[ 4.065430] tcpci_probe+0x118/0x2e0
To fix the issue, this will remove kree() from tcpm_port_unregister_pd().
Fixes: cd099cde4ed2 ("usb: typec: tcpm: Support multiple capabilities")
cc: [email protected]
Suggested-by: Aisheng Dong <[email protected]>
Signed-off-by: Xu Yang <[email protected]>
Acked-by: Heikki Krogerus <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
When auxiliary_device_add() returns error and then calls
auxiliary_device_uninit(), callback function ljca_auxdev_release
calls kfree(auxdev->dev.platform_data) to free the parameter data
of the function ljca_new_client_device. The callers of
ljca_new_client_device shouldn't call kfree() again
in the error handling path to free the platform data.
Fix this by cleaning up the redundant kfree() in all callers and
adding kfree() the passed in platform_data on errors which happen
before auxiliary_device_init() succeeds .
Fixes: acd6199f195d ("usb: Add support for Intel LJCA device")
Cc: stable <[email protected]>
Signed-off-by: Yongzhi Liu <[email protected]>
Reviewed-by: Hans de Goede <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
When orientation switch is enabled in ucsi glink, there is a xhci
probe failure seen when booting up in host mode in reverse
orientation.
During bootup the following things happen in multiple drivers:
a) DWC3 controller driver initializes the core in device mode when the
dr_mode is set to DRD. It relies on role_switch call to change role to
host.
b) QMP driver initializes the lanes to TYPEC_ORIENTATION_NORMAL as a
normal routine. It relies on the typec_switch_set call to get notified
of orientation changes.
c) UCSI core reads the UCSI_GET_CONNECTOR_STATUS via the glink and
provides initial role switch to dwc3 controller.
When booting up in host mode with orientation TYPEC_ORIENTATION_REVERSE,
then we see the following things happening in order:
a) UCSI gives initial role as host to dwc3 controller ucsi_register_port.
Upon receiving this notification, the dwc3 core needs to program GCTL from
PRTCAP_DEVICE to PRTCAP_HOST and as part of this change, it asserts GCTL
Core soft reset and waits for it to be completed before shifting it to
host. Only after the reset is done will the dwc3_host_init be invoked and
xhci is probed. DWC3 controller expects that the usb phy's are stable
during this process i.e., the phy init is already done.
b) During the 100ms wait for GCTL core soft reset, the actual notification
from PPM is received by ucsi_glink via pmic glink for changing role to
host. The pmic_glink_ucsi_notify routine first sends the orientation
change to QMP and then sends role to dwc3 via ucsi framework. This is
happening exactly at the time GCTL core soft reset is being processed.
c) When QMP driver receives typec switch to TYPEC_ORIENTATION_REVERSE, it
then re-programs the phy at the instant GCTL core soft reset has been
asserted by dwc3 controller due to which the QMP PLL lock fails in
qmp_combo_usb_power_on.
d) After the 100ms of GCTL core soft reset is completed, the dwc3 core
goes for initializing the host mode and invokes xhci probe. But at this
point the QMP is non-responsive and as a result, the xhci plat probe fails
during xhci_reset.
Fix this by passing orientation switch to available ucsi instances if
their gpio configuration is available before ucsi_register is invoked so
that by the time, the pmic_glink_ucsi_notify provides typec_switch to QMP,
the lane is already configured and the call would be a NOP thus not racing
with role switch.
Cc: [email protected]
Fixes: c6165ed2f425 ("usb: ucsi: glink: use the connector orientation GPIO to provide switch events")
Suggested-by: Wesley Cheng <[email protected]>
Signed-off-by: Krishna Kurapati <[email protected]>
Acked-by: Heikki Krogerus <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
In tcpm_pd_set, the array of port source capabilities is port->src_pdo,
not port->snk_pdo.
Fixes: cd099cde4ed2 ("usb: typec: tcpm: Support multiple capabilities")
Cc: [email protected]
Signed-off-by: Kyle Tso <[email protected]>
Acked-by: Heikki Krogerus <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
In the scenario of entering hibernation with udisk in the system, if the
udisk was gone or resume fail in the thaw phase of hibernation. Its state
will be set to NOTATTACHED. At this point, usb_hub_wq was already freezed
and can't not handle disconnect event. Next, in the poweroff phase of
hibernation, SYNCHRONIZE_CACHE SCSI command will be sent to this udisk
when poweroff this scsi device, which will cause uas_submit_urbs to be
called to submit URB for sense/data/cmd pipe. However, these URBs will
submit fail as device was set to NOTATTACHED state. Then, uas_submit_urbs
will return a value SCSI_MLQUEUE_DEVICE_BUSY to the caller. That will lead
the SCSI layer go into an ugly loop and system fail to go into hibernation.
On the other hand, when we specially check for -ENODEV in function
uas_queuecommand_lck, returning DID_ERROR to SCSI layer will cause device
poweroff fail and system shutdown instead of entering hibernation.
To fix this issue, let uas_submit_urbs to return original generic error
when submitting URB failed. At the same time, we need to translate -ENODEV
to DID_NOT_CONNECT for the SCSI layer.
Suggested-by: Oliver Neukum <[email protected]>
Cc: [email protected]
Signed-off-by: Weitao Wang <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
In order to be consistent with other s[n]printf() usage in this file,
switch to snprintf() here as well.
Signed-off-by: Christophe JAILLET <[email protected]>
Link: https://lore.kernel.org/r/5703e697687e4a39059bf90659969ffc86b2cfbd.1711176701.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
In order to be consistent with other strscpy() usage in this file and less
verbose, use the new 2-argument version of strscpy() which computes
auto-magically the size of the destination.
Signed-off-by: Christophe JAILLET <[email protected]>
Link: https://lore.kernel.org/r/e7fd0ec5a8b37799271c6d74c325cfb980d44181.1711176701.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The size given to strscpy() is not consistent with the destination buffer
that is used. The size is related to 'driver' and the buffer is
'mixername'.
sizeof(card->mixername) is 80 and sizeof(card->driver) is 16, so in
theory this could lead to unneeded string truncation.
In practice, this is not the case because g_audio_setup() has only 2
callers. 'card_name' is either "UAC1_Gadget" or "UAC2_Gadget".
Anyway, using the correct size is cleaner and more future proof.
In order to be less verbose, use the new 2-argument version of strscpy()
which computes auto-magically the size of the destination.
Signed-off-by: Christophe JAILLET <[email protected]>
Link: https://lore.kernel.org/r/bf8a9353319566624f653531b80e5caf3d346ba1.1711176700.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Added new bitfield GRSTCTL_CLOCK_SWITH_TIMER in GRSTCTL register.
This bitfield applicable HSOTG cores v5.00 or higher and not
applicable to HS/FS IOT devices.
This bitfield must be programmed to 3'b010 if core will be
used in Low-speed and core configured for any HS/FS PHY interface.
This bitfield must be programmed to 3'b111 if core configured
to use either:
- HS PHY interface UTMI or ULPI
- FS PHY any interface
Signed-off-by: Minas Harutyunyan <[email protected]>
Link: https://lore.kernel.org/r/0616838cfee958774c9321c6eeeda4be92f900d8.1708948356.git.Minas.Harutyunyan@synopsys.com
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Added programmming of ULPI_LATCH_EN_DURING_HIB_ENTRY bit in GPWRDN
register when using ULPI PHY during entry/exit to/from hibernation.
This bit set to 1 during entering to hibernation if ULPI PHY used.
On exiting from hibernation this bit reset to 0.
Applicable for both host and device modes.
Signed-off-by: Minas Harutyunyan <[email protected]>
Link: https://lore.kernel.org/r/e024cb39a7177ec201c873df25ca6365f2e55947.1708948356.git.Minas.Harutyunyan@synopsys.com
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|