| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This patch removes redundant condition.
(length && length > 5) can be reduced to a single evaluation.
Tested by compilation only.
Caught by cppcheck.
Signed-off-by: Geyslan G. Bem <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
This patch removes redundant conditions.
(!A || (A && B)) is the same as (!A || B).
Tested by compilation only.
Caught by cppcheck.
Signed-off-by: Geyslan G. Bem <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for-v4.4-rc5
Hopefully final set of fixes for v4.4 release cycle.
There's a fix for a regression on dwc3 caused by recent changes to how
transfers are started. We're not pre-starting interrupt endpoints
anymore.
A NULL pointer dereference fix for the MSM phy driver.
The UVC gadget got a minor fix for permissions to its configfs
attributes and, finally, two fixes for MUSB. A fix for PM runtime when
MUSB returns EPROBE_DEFER and a fix to actually return an error in case
we can't initialize a DMA engine.
Signed-off-by: Felipe Balbi <[email protected]>
|
|
Fail with error when no DMA controller is set.
Signed-off-by: Aaro Koskinen <[email protected]>
Signed-off-by: Felipe Balbi <[email protected]>
|
|
76e0da3 "usb-gadget/uvc: use per-attribute show and store methods"
removed write permission for writeable attributes. Correct attribute
permissions.
Fixes: 76e0da3 "usb-gadget/uvc: use per-attribute show and store methods"
Reviewed-by: Christoph Hellwig <[email protected]>
Reviewed-by: Laurent Pinchart <[email protected]>
Signed-off-by: Mian Yousaf Kaukab <[email protected]>
Signed-off-by: Felipe Balbi <[email protected]>
|
|
If musb_init_controller fails at musb_platform_init, we have already
called pm_runtime_irq_safe for musb and that causes the pm runtime count
to be enabled for parent before the parent has completed initialization.
This causes pm to stop working as on unload nothing gets idled.
This issue can be reproduced at least with:
# modprobe omap2430
HS USB OTG: no transceiver configured
musb-hdrc musb-hdrc.0.auto: musb_init_controller failed with status -517
# modprobe phy-twl4030-usb
# rmmod omap2430
And after the steps above omap2430 will block deeper idle states on
omap3.
To fix this, let's not enable pm runtime until we need to and the
parent has been initialized. Note that this does not fix the issue of
PM being broken for musb during runtime.
Signed-off-by: Tony Lindgren <[email protected]>
Signed-off-by: Felipe Balbi <[email protected]>
|
|
of_match_device could return NULL, and so cause a NULL pointer
dereference later.
Even if the probability of this case is very low, fixing it made
static analyzers happy.
Solving this with of_device_get_match_data made also code simplier.
Reported-by: coverity (CID 1324133)
Signed-off-by: LABBE Corentin <[email protected]>
Signed-off-by: Felipe Balbi <[email protected]>
|
|
When assigning bool use true instead of 1. If declaring it as static and
it's false there's no need to initialize it, since static variables are
zeroed by default.
Caught by coccinelle.
Signed-off-by: Geyslan G. Bem <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The module should fail to load.
Signed-off-by: Oliver Neukum <[email protected]>
CC: [email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
It shouldn't matter how usbcore is compiled. As it is a subsystem,
the correct way to use nousb should be usbcore.nousb
Signed-off-by: Oliver Neukum <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Replace BUG() with BUG_ON().
Caught by coccinelle.
Signed-off-by: Geyslan G. Bem <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Get rid of bool explicit comparisons.
Caught by Coccinelle.
Signed-off-by: Geyslan G. Bem <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Currently usb_port_resume waits for up to 2 seconds for CONNECT
status for SS devices only. This change will do the same thing for
non-SS devices even though the reason is a little different. This
will fix an issue where VBUS is turned off during system wide
"suspend to ram" and some 2.0 devices take greater than the current
max of 100ms to show connected after VBUS is enabled. This is most
commonly seen on hard drive based devices and USB3.0 devices plugged
into a 2.0 only port.
Signed-off-by: Al Cooper <[email protected]>
Acked-by: Alan Stern <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The interrupt handler, ohci_hcd_at91_overcurrent_irq may be called right
after registration. At that time, pdev->dev.platform_data is not yet set,
leading to a NULL pointer dereference.
Fixes: e4df92279fd9 (USB: host: ohci-at91: merge loops in ohci_hcd_at91_drv_probe)
Reported-by: Peter Rosin <[email protected]>
Tested-by: Peter Rosin <[email protected]>
Signed-off-by: Alexandre Belloni <[email protected]>
Cc: [email protected] # 4.3+
Acked-by: Nicolas Ferre <[email protected]>
Acked-by: Alan Stern <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
My recent Intel box is spewing these messages:
xhci_hcd 0000:00:14.0: xHCI Host Controller
xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 2
usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: xHCI Host Controller
usb usb2: Manufacturer: Linux 4.3.0+ xhci-hcd
usb usb2: SerialNumber: 0000:00:14.0
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 6 ports detected
usb: failed to peer usb2-port2 and usb1-port1 by location (usb2-port2:none) (usb1-port1:usb2-port1)
usb usb2-port2: failed to peer to usb1-port1 (-16)
usb: port power management may be unreliable
usb: failed to peer usb2-port3 and usb1-port1 by location (usb2-port3:none) (usb1-port1:usb2-port1)
usb usb2-port3: failed to peer to usb1-port1 (-16)
usb: failed to peer usb2-port5 and usb1-port1 by location (usb2-port5:none) (usb1-port1:usb2-port1)
usb usb2-port5: failed to peer to usb1-port1 (-16)
usb: failed to peer usb2-port6 and usb1-port1 by location (usb2-port6:none) (usb1-port1:usb2-port1)
usb usb2-port6: failed to peer to usb1-port1 (-16)
Diving into the acpi tables, I noticed the EHCI hub has 12 ports while the XHCI
hub has 8 ports. Most of those ports are of connect type USB_PORT_NOT_USED
(including port 1 of the EHCI hub).
Further the unused ports have location data initialized to 0x80000000.
Now each unused port on the xhci hub walks the port list and finds a matching
peer with port1 of the EHCI hub because the zero'd out group id bits falsely match.
After port1 of the XHCI hub, each following matching peer will generate the
above warning.
These warnings seem to be harmless for this scenario as I don't think it
matters that unused ports could not create a peer link.
The attached patch utilizes that assumption and just turns the pr_warn into
pr_debug to quiet things down.
Tested on my Intel box.
Signed-off-by: Don Zickus <[email protected]>
Acked-by: Dan Williams <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
if a full speed hub connects to a high speed hub which
supports MTT, the MTT field of its slot context will be set
to 1 when xHCI driver setups an xHCI virtual device in
xhci_setup_addressable_virt_dev(); once usb core fetch its
hub descriptor, and need to update the xHC's internal data
structures for the device, the HUB field of its slot context
will be set to 1 too, meanwhile MTT is also set before,
this will cause configure endpoint command fail, so in the
case, we should clear MTT to 0 for full speed hub according
to section 6.2.2
Signed-off-by: Chunfeng Yun <[email protected]>
Cc: stable <[email protected]>
Signed-off-by: Mathias Nyman <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
There is a memory leak because acpi_evaluate_dsm() actually returns an
object which the caller is supposed to release. Fix this by calling
ACPI_FREE() for the returned object (this expands to kfree() so passing
NULL there is fine as well).
While there correct indentation in !CONFIG_ACPI case.
Signed-off-by: Mika Westerberg <[email protected]>
Cc: stable <[email protected]> # v4.2
Signed-off-by: Mathias Nyman <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
USB3 LPM is default on in Linux kernel if both xHCI host controller
and the USB devices declare to be LPM-capable. Unfortunately, some
devices are known to work well with LPM disabled, but to be broken
if LPM is enabled, although it declares the LPM capability. Users
won't be able to use this kind of devices, until someone puts them
in the kernel blacklist and gets the kernel upgraded.
This patch adds a sysfs node to permit or forbit USB3 LPM U1 or U2
entry for a port. The settings apply to both before and after device
enumeration. Supported values are "0" - neither u1 nor u2 permitted,
"u1" - only u1 is permitted, "u2" - only u2 is permitted, "u1_u2" -
both u1 and u2 are permitted. With this interface, users can use an
LPM-unfriendly USB device on a released Linux kernel.
Signed-off-by: Lu Baolu <[email protected]>
Signed-off-by: Zhuang Jin Can <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Commit 655fe4effe0f ("usbcore: add sysfs support to xHCI usb3
hardware LPM") introduced usb3_hardware_lpm sysfs node. This
doesn't show the correct status of USB3 U1 and U2 LPM status.
This patch fixes this by replacing usb3_hardware_lpm with two
nodes, usb3_hardware_lpm_u1 (for U1) and usb3_hardware_lpm_u2
(for U2), and recording the U1/U2 LPM status in right places.
This patch should be back-ported to kernels as old as 4.3,
that contains Commit 655fe4effe0f ("usbcore: add sysfs support
to xHCI usb3 hardware LPM").
Cc: [email protected]
Signed-off-by: Lu Baolu <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
This patch sets the AHBMODE to allow for posted data writes. This
results in higher performance.
Signed-off-by: Andy Gross <[email protected]>
Tested-by: Georgi Djakov <[email protected]>
Acked-by: Alan Stern <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
This patch sets the AHBMODE to allow for posted data writes. This
results in higher performance.
Signed-off-by: Andy Gross <[email protected]>
Acked-by: Peter Chen <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
struct mon_bin_hdr allows for a 64-bit seconds timestamp. The code
currently uses 'struct timeval' to populate the timestamp in mon_bin_hdr,
which has a 32-bit seconds field and will overflow in year 2038 and beyond.
This patch replaces 'struct timeval' with 'struct timespec64' which is
y2038 safe. This patch is part of a larger attempt to remove instances
of struct timeval and other 32-bit timekeeping (time_t, struct timespec)
from the kernel.
Signed-off-by: Tina Ruchandani <[email protected]>
Reviewed-by: Arnd Bergmann <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
timeval is deprecated and not y2038 safe. Its size also changes according
to 32 bit/ 64 bit compilation. Replace it with 32 and 64 bit versions of
its individual fields, giving two ioctls with different code values.
The two ioctls are necessary to maintain the 32 bit and 64 bit userspace
compatibility with a 64/32 bit kernel.
Change unsigned to __u32 types for a definitive userspace interface.
This is in accordance with the psABI that the unsigned type is always
32 bits.
Also use motonic timer instead of real time to ensure positive delta
values.
Refactor usbtest_ioctl for readability to isolate the handling of the
testing timing measurement.
The official testusb userspace tool can be changed in a separate patch
to reflect the __u32 changes as well. It can use the usbtest_param_32
struct, since 32 bit seconds is long enough for test durations.
Signed-off-by: Deepa Dinamani <[email protected]>
Reviewed-by: Arnd Bergmann <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
struct timeval' uses 32-bits for its seconds field and will overflow in
the year 2038 and beyond. This patch replaces the usage of 'struct timeval'
in mon_get_timestamp() with timespec64 which uses a 64-bit seconds field
and is y2038-safe. mon_get_timestamp() truncates the timestamp at 4096 seconds,
so the correctness of the code is not affected. This patch is part of a larger
attempt to remove instances of struct timeval and other 32-bit timekeeping
(time_t, struct timespec) from the kernel.
Signed-off-by: Tina Ruchandani <[email protected]>
Suggested-by: Arnd Bergmann <[email protected]>
Reviewed-by: Arnd Bergmann <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
So far we were using simple (legacy) GPIO functions & some poor logic to
control power. It got many drawbacks: we were ignoring OF flags
(GPIO_ACTIVE_LOW), we were not setting direction to output and we were
assuming gpio_request success all the time.
Fix it by switching to gpiod functions and adding appropriate checks.
Signed-off-by: Rafał Miłecki <[email protected]>
Acked-by: Hauke Mehrtens <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
usb_parse_ss_endpoint_companion() now decodes the burst multiplier
correctly in order to check that it's <= 3, but still uses the wrong
expression if warning that it's > 3.
Fixes: ff30cbc8da42 ("usb: Use the USB_SS_MULT() macro to get the ...")
Signed-off-by: Ben Hutchings <[email protected]>
Cc: stable <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
qset_fill_page_list() do not check for dma mapping errors.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <[email protected]>
Cc: stable <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
When a USB 3.0 mass storage device is disconnected in transporting
state, storage device driver may handle it as a transport error and
reset the device by invoking usb_reset_and_verify_device()
and following could happen:
in usb_reset_and_verify_device():
udev->bos = NULL;
For U1/U2 enabled devices, driver will disable LPM, and in some
conditions:
from usb_unlocked_disable_lpm()
--> usb_disable_lpm()
--> usb_enable_lpm()
udev->bos->ss_cap->bU1devExitLat;
And it causes 'NULL pointer' and 'kernel panic':
[ 157.976257] Unable to handle kernel NULL pointer dereference
at virtual address 00000010
...
[ 158.026400] PC is at usb_enable_link_state+0x34/0x2e0
[ 158.031442] LR is at usb_enable_lpm+0x98/0xac
...
[ 158.137368] [<ffffffc0006a1cac>] usb_enable_link_state+0x34/0x2e0
[ 158.143451] [<ffffffc0006a1fec>] usb_enable_lpm+0x94/0xac
[ 158.148840] [<ffffffc0006a20e8>] usb_disable_lpm+0xa8/0xb4
...
[ 158.214954] Kernel panic - not syncing: Fatal exception
This commit moves 'udev->bos = NULL' behind usb_unlocked_disable_lpm()
to prevent from NULL pointer access.
Issue can be reproduced by following setup:
1) A SS pen drive behind a SS hub connected to the host.
2) Transporting data between the pen drive and the host.
3) Abruptly disconnect hub and pen drive from host.
4) With a chance it crashes.
Signed-off-by: Hans Yang <[email protected]>
Acked-by: Alan Stern <[email protected]>
Cc: stable <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The usb_mon_operations structure is never modified, so declare it as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Now the function of complicated_callback is not only used for iso
transfer, improve the error message to reflect it.
Signed-off-by: Peter Chen <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
for checking if a property is present or not,
of_property_read_bool is more appropriate than of_get_property()
Signed-off-by: Saurabh Sengar <[email protected]>
Acked-by: Alan Stern <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
This function must be called with a spinlock held.
Memory can be allocated only with GFP_ATOMIC. Passing
a gfp_t argument is a waste.
Signed-off-by: Oliver Neukum <[email protected]>
Reviewed-by: Hans de Goede <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Use this macro to make the driver more readable.
Signed-off-by: Oliver Neukum <[email protected]>
Reviewed-by: Hans de Goede <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The dma_pool_destroy() function tests whether its argument is NULL
and then returns immediately. Thus the test around the calls is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <[email protected]>
Acked-by: Alan Stern <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
replace dma_pool_alloc and memset with a single call to dma_pool_zalloc
Signed-off-by: Saurabh Sengar <[email protected]>
Acked-by: Peter Chen <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Replace the existing two extended capability parsing helper functions with
one called xhci_find_next_ext_cap().
The extended capabilities are read both in pci-quirks before xhci driver is
loaded, and inside the xhci driver when adding ports. The existing helpers
did not suit well for these cases and a lot of custom parsing code was
needed.
The new helper function simplifies these two cases a lot.
The motivation for this rework was that code to support xhci debug
capability needed to parse extended capabilities, and it included
yet another capability parsing helper specific for its needs. With
this solution it debug capability code can use this new helper as well
Signed-off-by: Mathias Nyman <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Don't use dev_warn() for intened behaviour, use dev_dbg()
Rounding down the interval to the nearest power of 2 is required
by xhci specs.
Signed-off-by: Mathias Nyman <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
There some vendor quirks for MTK xhci host controller:
1. It defines some extra SW scheduling parameters for HW
to minimize the scheduling effort for synchronous and
interrupt endpoints. The parameters are put into reseved
DWs of slot context and endpoint context.
2. Its IMODI unit for Interrupter Moderation register is
8 times as much as that defined in xHCI spec.
3. Its TDS in Normal TRB defines a number of packets that
remains to be transferred for a TD after processing all
Max packets in all previous TRBs.
Signed-off-by: Chunfeng Yun <[email protected]>
Tested-by: Daniel Thompson <[email protected]>
Reviewed-by: Daniel Thompson <[email protected]>
Signed-off-by: Mathias Nyman <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The R-Car H3 has two xHCI controllers. This SoC is compatible with
R-Car Gen2 SoCs, however this SoC doesn't need some specific registers
setting, and need a new firmware.
Signed-off-by: Yoshihiro Shimoda <[email protected]>
Signed-off-by: Mathias Nyman <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
This patch adds support for R-Car M2-N (r8a7793) xHCI controller.
This SoC is compatible with R-Car H2 (r8a7790) and R-Car M2-W (r8a7791).
Signed-off-by: Yoshihiro Shimoda <[email protected]>
Signed-off-by: Mathias Nyman <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
This patch changes code to ease the addition of next generation SoCs.
Signed-off-by: Yoshihiro Shimoda <[email protected]>
Signed-off-by: Mathias Nyman <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
This patch adds a member "firmware_name" in struct xhci_plat_priv
to simplify the code to match specific firmware name.
Signed-off-by: Yoshihiro Shimoda <[email protected]>
Signed-off-by: Mathias Nyman <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
This patch adds struct xhci_plat_priv to simplify the code to match
platform specific variables. For now, this patch adds a member "type"
in the structure.
Signed-off-by: Yoshihiro Shimoda <[email protected]>
Signed-off-by: Mathias Nyman <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
This patch adds an xhci->priv field for private use by
XHCI platform drivers. Until now none of the platform drivers
has used this private space.
Signed-off-by: Yoshihiro Shimoda <[email protected]>
Signed-off-by: Mathias Nyman <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
This patch cleanups the hcd private size to suitable size.
The previous code has "sizeof(struct xhci_hcd *)" in xhci_hc_driver
as hcd_priv_size and sizeof(struct xhci_hcd) in xhci_plat_overrides
or xhci_pci_overrides as extra_priv_size. However, the xhci driver
uses a "sizeof(struct xhcd_hcd)" memory space in each hcd
(main_hcd and shared_hcd) actually.
Signed-off-by: Yoshihiro Shimoda <[email protected]>
Signed-off-by: Mathias Nyman <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
use the variables defined for populating the port status and
port chage bits retuend by GetPortStatus request intead of
the hub class feature selectors.
The defines for hub class feature selectors are used for other purposes,
they work as port status and feature selectors are in the same order, and
set the same bits, but it makes the code very hard to follow
Signed-off-by: Mathias Nyman <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
This patch adds a new warning message to ehci-hcd. The warning is
triggered whenever the driver finds that the hardware has set the
Active bit in a QH at a time when the driver expects the QH to be
completely idle. Such bugs have been observed by users in the past,
and since they can lead to serious problems (such as inability to
unlink an URB that never completes), it would be good to know about
them when they occur.
This won't fix these bugs; that's a bigger job for a later patch. But
success isn't guaranteed, since this depends on aspects of the
hardware which are not documented in the EHCI spec or for which the
spec's recommendations are clearly unworkable. It therefore seems
worthwhile to check for these bugs proactively.
Signed-off-by: Alan Stern <[email protected]>
Reported-by: Michael Reutman <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
This patch enhances the "async" debugfs file in ehci-hcd by printing
out several additional fields in the hardware-accessible data
structures. These fields are important for determining the hardware's
view of the async schedule, in particular, the addresses of the
current and next qTDs for each QH along with the start address of each
qTD's data buffer.
Signed-off-by: Alan Stern <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
This patch improves the usbfs_snoop debugging facility by adding
messages for a couple of significant events which, up to now, have not
been logged. The events are reaping and discarding (i.e.,
cancelling) an URB. The debugging messages include the userspace
address of the URB being reaped or discarded.
The reaping messages have to be added in four places, in order to
handle blocking and non-blocking reaps in both normal and 32-bit
compatibility mode.
Signed-off-by: Alan Stern <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The usbfs_snoop facility can be very useful for debugging problems
involving usbfs. However, it always prints out the entire contents of
every URB. When dealing with large quantities of data, this can be
less than helpful.
This patch ameliorates the situation by adding a module parameter to
usbcore for controlling the maximum number of bytes to print when
snooping an URB. This makes debugging much easier. For backward
compatibility, the default value is set unreasonably high.
Signed-off-by: Alan Stern <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|