aboutsummaryrefslogtreecommitdiff
path: root/drivers/usb
AgeCommit message (Collapse)AuthorFilesLines
2021-06-15usb: mtu3: rebuild role switch flow of extconChunfeng Yun2-32/+38
This is a preparation patch to plan to use the same work to handle role switch for all three supported ways. Signed-off-by: Chunfeng Yun <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2021-06-15usb: mtu3: use enum usb_role instead of private defined onesChunfeng Yun1-37/+15
Now we mainly use usb-role-switch to set dual role mode, and all three ways supported use the same function to switch mode, use usb_role enum will make code clear Signed-off-by: Chunfeng Yun <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2021-06-15usb: mtu3: drop support vbus detectionChunfeng Yun2-55/+2
Until now it's never used on any platform, and will not used later. Signed-off-by: Chunfeng Yun <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2021-06-15usb: mtu3: remove wakelockChunfeng Yun1-3/+0
Prefer to use /sys/power/wake_lock instead. Signed-off-by: Chunfeng Yun <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2021-06-15usb: mtu3: power down port when power down device IPChunfeng Yun1-0/+9
When power down device IP, we can also power down device port, then power on the port again when power on device ip, it's helpful to make device ip enter ip sleep mode. Signed-off-by: Chunfeng Yun <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2021-06-15usb: mtu3: power down device IP by defaultChunfeng Yun1-4/+3
Power down device IP by default until @udc_start is called. Signed-off-by: Chunfeng Yun <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2021-06-15usb: isp1760: Fix meaningless check in isp1763_run()Tong Tiangen1-1/+0
Remove attribution to retval before check, which make it completely meaningless, and does't check what it was supposed: the return value of the timed function to set up configuration flag. Fixes: 60d789f3bfbb ("usb: isp1760: add support for isp1763") Tested-by: Rui Miguel Silva <[email protected]> Reviewed-by: Rui Miguel Silva <[email protected]> Signed-off-by: Tong Tiangen <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2021-06-15usb: renesas-xhci: Replace BIT(15) with macroMoritz Fischer1-1/+1
Replace BIT(15) with RENESAS_ROM_STATUS_ROM_EXISTS. Signed-off-by: Moritz Fischer <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2021-06-15usb: phy: tegra: Correct definition of B_SESS_VLD_WAKEUP_EN bitDmitry Osipenko1-3/+2
The B_SESS_VLD_WAKEUP_EN bit 6 was added by a mistake in a previous commit. This bit corresponds to B_SESS_END_WAKEUP_EN, which we don't use. The B_VBUS_VLD_WAKEUP_EN doesn't exist at all and B_SESS_VLD_WAKEUP_EN needs to be in place of it. We don't utilize B-sensors in the driver, so it never was a problem, nevertheless let's correct the definition of the bits. Fixes: 35192007d28d ("usb: phy: tegra: Support waking up from a low power mode") Signed-off-by: Dmitry Osipenko <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2021-06-15usb: phy: tegra: Wait for VBUS wakeup status deassertion on suspendDmitry Osipenko1-0/+10
Some devices need an extra delay after losing VBUS, otherwise VBUS may be detected as active at suspend time, preventing the PHY's suspension by the VBUS detection sensor. This problem was found on Asus Transformer TF700T (Tegra30) tablet device, where the USB PHY wakes up immediately from suspend because VBUS sensor continues to detect VBUS as active after disconnection. We need to poll the PHY's VBUS wakeup status until it's deasserted before suspending PHY in order to fix this minor trouble. Fixes: 35192007d28d ("usb: phy: tegra: Support waking up from a low power mode") Reported-by: Maxim Schwalm <[email protected]> # Asus TF700T Tested-by: Maxim Schwalm <[email protected]> # Asus TF700T Reviewed-by: Peter Chen <[email protected]> Signed-off-by: Dmitry Osipenko <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2021-06-15tty: make use of tty_get_{char,frame}_sizeJiri Slaby5-73/+7
In the previous patch, we introduced tty_get_char_size() and tty_get_frame_size() for computing character and frame sizes, respectively. Here, we make use of them in various tty drivers where applicable. The stats look nice: 12 insertions, 169 deletions. Cc: Arnd Bergmann <[email protected]> Cc: David Lin <[email protected]> Cc: Johan Hovold <[email protected]> Cc: Alex Elder <[email protected]> Cc: Shawn Guo <[email protected]> Cc: Sascha Hauer <[email protected]> Cc: Andy Gross <[email protected]> Cc: Bjorn Andersson <[email protected]> Cc: Maxime Coquelin <[email protected]> Cc: Alexandre Torgue <[email protected]> Cc: Oliver Neukum <[email protected]> Acked-by: Alex Elder <[email protected]> Signed-off-by: Jiri Slaby <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2021-06-15cypress_m8: switch data_bits to real character bitsJiri Slaby1-6/+6
Make data_bits what it really is. Assign proper bit counts to data_bits instead of magic 0..3. There are two reasons: 1) it's clear what we store there, and 2) it will make the transition to tty_tty_get_char_size() in the next patch easier. Signed-off-by: Jiri Slaby <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2021-06-15usb: dwc3: core: fix kernel panic when do rebootPeter Chen1-1/+1
When do system reboot, it calls dwc3_shutdown and the whole debugfs for dwc3 has removed first, when the gadget tries to do deinit, and remove debugfs for its endpoints, it meets NULL pointer dereference issue when call debugfs_lookup. Fix it by removing the whole dwc3 debugfs later than dwc3_drd_exit. [ 2924.958838] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000002 .... [ 2925.030994] pstate: 60000005 (nZCv daif -PAN -UAO -TCO BTYPE=--) [ 2925.037005] pc : inode_permission+0x2c/0x198 [ 2925.041281] lr : lookup_one_len_common+0xb0/0xf8 [ 2925.045903] sp : ffff80001276ba70 [ 2925.049218] x29: ffff80001276ba70 x28: ffff0000c01f0000 x27: 0000000000000000 [ 2925.056364] x26: ffff800011791e70 x25: 0000000000000008 x24: dead000000000100 [ 2925.063510] x23: dead000000000122 x22: 0000000000000000 x21: 0000000000000001 [ 2925.070652] x20: ffff8000122c6188 x19: 0000000000000000 x18: 0000000000000000 [ 2925.077797] x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000004 [ 2925.084943] x14: ffffffffffffffff x13: 0000000000000000 x12: 0000000000000030 [ 2925.092087] x11: 0101010101010101 x10: 7f7f7f7f7f7f7f7f x9 : ffff8000102b2420 [ 2925.099232] x8 : 7f7f7f7f7f7f7f7f x7 : feff73746e2f6f64 x6 : 0000000000008080 [ 2925.106378] x5 : 61c8864680b583eb x4 : 209e6ec2d263dbb7 x3 : 000074756f307065 [ 2925.113523] x2 : 0000000000000001 x1 : 0000000000000000 x0 : ffff8000122c6188 [ 2925.120671] Call trace: [ 2925.123119] inode_permission+0x2c/0x198 [ 2925.127042] lookup_one_len_common+0xb0/0xf8 [ 2925.131315] lookup_one_len_unlocked+0x34/0xb0 [ 2925.135764] lookup_positive_unlocked+0x14/0x50 [ 2925.140296] debugfs_lookup+0x68/0xa0 [ 2925.143964] dwc3_gadget_free_endpoints+0x84/0xb0 [ 2925.148675] dwc3_gadget_exit+0x28/0x78 [ 2925.152518] dwc3_drd_exit+0x100/0x1f8 [ 2925.156267] dwc3_remove+0x11c/0x120 [ 2925.159851] dwc3_shutdown+0x14/0x20 [ 2925.163432] platform_shutdown+0x28/0x38 [ 2925.167360] device_shutdown+0x15c/0x378 [ 2925.171291] kernel_restart_prepare+0x3c/0x48 [ 2925.175650] kernel_restart+0x1c/0x68 [ 2925.179316] __do_sys_reboot+0x218/0x240 [ 2925.183247] __arm64_sys_reboot+0x28/0x30 [ 2925.187262] invoke_syscall+0x48/0x100 [ 2925.191017] el0_svc_common.constprop.0+0x48/0xc8 [ 2925.195726] do_el0_svc+0x28/0x88 [ 2925.199045] el0_svc+0x20/0x30 [ 2925.202104] el0_sync_handler+0xa8/0xb0 [ 2925.205942] el0_sync+0x148/0x180 [ 2925.209270] Code: a9025bf5 2a0203f5 121f0056 370802b5 (79400660) [ 2925.215372] ---[ end trace 124254d8e485a58b ]--- [ 2925.220012] Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b [ 2925.227676] Kernel Offset: disabled [ 2925.231164] CPU features: 0x00001001,20000846 [ 2925.235521] Memory Limit: none [ 2925.238580] ---[ end Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b ]--- Fixes: 8d396bb0a5b6 ("usb: dwc3: debugfs: Add and remove endpoint dirs dynamically") Cc: Jack Pham <[email protected]> Tested-by: Jack Pham <[email protected]> Signed-off-by: Peter Chen <[email protected]> Link: https://lore.kernel.org/r/[email protected] (cherry picked from commit 2a042767814bd0edf2619f06fecd374e266ea068) Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2021-06-14usb: gadget: fsl: properly remove remnant of MXC supportLi Yang2-49/+6
Commit a390bef7db1f ("usb: gadget: fsl_mxc_udc: Remove the driver") didn't remove all the MXC related stuff which can cause build problem for LS1021 when enabled again in Kconfig. This patch remove all the remnants. Reviewed-by: Fabio Estevam <[email protected]> Acked-by: Arnd Bergmann <[email protected]> Signed-off-by: Li Yang <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2021-06-14Merge tag 'for-5.14-usb' of ↵Greg Kroah-Hartman1-131/+482
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into usb-next Thierry writes: usb: tegra: Changes for v5.14-rc1 Implements proper suspend/resume for the XUSB controller found on recent Tegra chips. * tag 'for-5.14-usb' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: usb: xhci: tegra: Enable ELPG for runtime/system PM usb: xhci: tegra: Unlink power domain devices phy: tegra: xusb: Add wake/sleepwalk for Tegra186 phy: tegra: xusb: Tegra210 host mode VBUS control phy: tegra: xusb: Add wake/sleepwalk for Tegra210 phy: tegra: xusb: Add sleepwalk and suspend/resume phy: tegra: xusb: Add Tegra210 lane_iddq operation phy: tegra: xusb: Rearrange UPHY init on Tegra210 phy: tegra: xusb: Move usb3 port init for Tegra210
2021-06-14usb: musb: Implement tracing for state change eventsTony Lindgren2-16/+35
The devctl register on musb is the only way to get state information on musb. The hardware can easily get confused because it tries to do things on it's own automagically, and things like slow VBUS rise can make things fail. Let's make it easier to debug the ongoing state change issues that keep popping up on regular basis and add tracing support. With these changes we can easily trace musb state change events with: echo 1 > /sys/kernel/debug/tracing/events/musb/musb_state/enable cat /sys/kernel/debug/tracing/trace_pipe echo 0 > /sys/kernel/debug/tracing/events/musb/musb_state/enable Cc: Alexandre Belloni <[email protected]> Cc: Andreas Kemnade <[email protected]> Cc: Bhushan Shah <[email protected]> Cc: Drew Fustini <[email protected]> Cc: Thomas Petazzoni <[email protected]> Signed-off-by: Tony Lindgren <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2021-06-14usb: musb: Simplify cable state handlingTony Lindgren1-20/+20
Simplify cable state handling a bit to leave out duplicated code. We are just scheduling work and showing state info if a recheck is needed. No intended functional changes. Cc: Alexandre Belloni <[email protected]> Cc: Andreas Kemnade <[email protected]> Cc: Bhushan Shah <[email protected]> Cc: Drew Fustini <[email protected]> Cc: Thomas Petazzoni <[email protected]> Signed-off-by: Tony Lindgren <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2021-06-14Merge tag 'v5.13-rc6' into usb-nextGreg Kroah-Hartman33-107/+250
We want the usb fixes in here as well, and this resolves some merge issues with: drivers/usb/dwc3/debugfs.c drivers/usb/dwc3/gadget.c Signed-off-by: Greg Kroah-Hartman <[email protected]>
2021-06-14Merge tag 'v5.13-rc6' into tty-nextGreg Kroah-Hartman35-126/+258
We want the tty fixes in here as well. Signed-off-by: Greg Kroah-Hartman <[email protected]>
2021-06-11usb: xhci: tegra: Enable ELPG for runtime/system PMJC Kuo1-37/+370
This commit implements the complete programming sequence for ELPG entry and exit. 1. At ELPG entry, invokes tegra_xusb_padctl_enable_phy_sleepwalk() and tegra_xusb_padctl_enable_phy_wake() to configure XUSB PADCTL sleepwalk and wake detection circuits to maintain USB lines level and respond to wake events (wake-on-connect, wake-on-disconnect, device-initiated-wake). 2. At ELPG exit, invokes tegra_xusb_padctl_disable_phy_sleepwalk() and tegra_xusb_padctl_disable_phy_wake() to disarm sleepwalk and wake detection circuits. At runtime suspend, XUSB host controller can enter ELPG to reduce power consumption. When XUSB PADCTL wake detection circuit detects a wake event, an interrupt will be raised. xhci-tegra driver then will invoke pm_runtime_resume() for xhci-tegra. Runtime resume could also be triggered by protocol drivers, this is the host-initiated-wake event. At runtime resume, xhci-tegra driver brings XUSB host controller out of ELPG to handle the wake events. The same ELPG enter/exit procedure will be performed for system suspend/resume path so USB devices can remain connected across SC7. Signed-off-by: JC Kuo <[email protected]> Acked-by: Greg Kroah-Hartman <[email protected]> Signed-off-by: Thierry Reding <[email protected]>
2021-06-11usb: xhci: tegra: Unlink power domain devicesJC Kuo1-94/+112
This commit unlinks xhci-tegra platform device with SS/host power domain devices. Reasons for this change is - at ELPG entry, PHY sleepwalk and wake configuration need to be done before powering down SS/host partitions, and PHY need be powered off after powering down SS/host partitions. Sequence looks like roughly below: tegra_xusb_enter_elpg() -> xhci_suspend() -> enable PHY sleepwalk and wake if needed -> power down SS/host partitions -> power down PHY If SS/host power domains are linked to xhci-tegra platform device, we are not able to perform the sequence like above. This commit introduces: 1. tegra_xusb_unpowergate_partitions() to power up SS and host partitions together. If SS/host power domain devices are available, it invokes pm_runtime_get_sync() to request power driver to power up partitions; If power domain devices are not available, tegra_powergate_sequence_power_up() will be used to power up partitions. 2. tegra_xusb_powergate_partitions() to power down SS and host partitions together. If SS/host power domain devices are available, it invokes pm_runtime_put_sync() to request power driver to power down partitions; If power domain devices are not available, tegra_powergate_power_off() will be used to power down partitions. Signed-off-by: JC Kuo <[email protected]> Acked-by: Greg Kroah-Hartman <[email protected]> Signed-off-by: Thierry Reding <[email protected]>
2021-06-11Merge tag 'usb-serial-5.13-rc6' of ↵Greg Kroah-Hartman1-6/+78
https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus Johan writes: USB-serial fixes for 5.13-rc6 Here are two fixes for the cp210x driver. The first fixes a regression with early revisions of the CP2102N which specifically broke some ESP32 development boards. The second makes sure that the pin configuration is detected properly also for the CP2102N QFN20 package. Both have been in linux-next over night and with no reported issues. * tag 'usb-serial-5.13-rc6' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial: USB: serial: cp210x: fix CP2102N-A01 modem control USB: serial: cp210x: fix alternate function for CP2102N QFN20
2021-06-11Revert "usb: gadget: fsl: Re-enable driver for ARM SoCs"Greg Kroah-Hartman1-1/+1
This reverts commit e0e8b6abe8c862229ba00cdd806e8598cdef00bb. Turns out this breaks the build. We had numerous reports of problems from linux-next and 0-day about this not working properly, so revert it for now until it can be figured out properly. The build errors are: arm-linux-gnueabi-ld: fsl_udc_core.c:(.text+0x29d4): undefined reference to `fsl_udc_clk_finalize' arm-linux-gnueabi-ld: fsl_udc_core.c:(.text+0x2ba8): undefined reference to `fsl_udc_clk_release' fsl_udc_core.c:(.text+0x2848): undefined reference to `fsl_udc_clk_init' fsl_udc_core.c:(.text+0xe88): undefined reference to `fsl_udc_clk_release' Reported-by: Stephen Rothwell <[email protected]> Reported-by: kernel test robot <[email protected]> Fixes: e0e8b6abe8c8 ("usb: gadget: fsl: Re-enable driver for ARM SoCs") Cc: stable <[email protected]> Cc: Joel Stanley <[email protected]> Cc: Leo Li <[email protected]> Cc: Peter Chen <[email protected]> Cc: Arnd Bergmann <[email protected]> Cc: Felipe Balbi <[email protected]> Cc: Shawn Guo <[email protected]> Cc: Ran Wang <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
2021-06-10usb: typec: mux: Fix copy-paste mistake in typec_mux_matchBjorn Andersson1-1/+1
Fix the copy-paste mistake in the return path of typec_mux_match(), where dev is considered a member of struct typec_switch rather than struct typec_mux. The two structs are identical in regards to having the struct device as the first entry, so this provides no functional change. Fixes: 3370db35193b ("usb: typec: Registering real device entries for the muxes") Reviewed-by: Heikki Krogerus <[email protected]> Signed-off-by: Bjorn Andersson <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2021-06-10usb: typec: ucsi: Clear PPM capability data in ucsi_init() error pathMayank Rana1-0/+1
If ucsi_init() fails for some reason (e.g. ucsi_register_port() fails or general communication failure to the PPM), particularly at any point after the GET_CAPABILITY command had been issued, this results in unwinding the initialization and returning an error. However the ucsi structure's ucsi_capability member retains its current value, including likely a non-zero num_connectors. And because ucsi_init() itself is done in a workqueue a UCSI interface driver will be unaware that it failed and may think the ucsi_register() call was completely successful. Later, if ucsi_unregister() is called, due to this stale ucsi->cap value it would try to access the items in the ucsi->connector array which might not be in a proper state or not even allocated at all and results in NULL or invalid pointer dereference. Fix this by clearing the ucsi->cap value to 0 during the error path of ucsi_init() in order to prevent a later ucsi_unregister() from entering the connector cleanup loop. Fixes: c1b0bc2dabfa ("usb: typec: Add support for UCSI interface") Cc: [email protected] Acked-by: Heikki Krogerus <[email protected]> Signed-off-by: Mayank Rana <[email protected]> Signed-off-by: Jack Pham <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2021-06-10usb: gadget: fsl: Re-enable driver for ARM SoCsJoel Stanley1-1/+1
The commit a390bef7db1f ("usb: gadget: fsl_mxc_udc: Remove the driver") dropped the ARCH_MXC dependency from USB_FSL_USB2, leaving it depending solely on FSL_SOC. FSL_SOC is powerpc only; it was briefly available on ARM in 2014 but was removed by commit cfd074ad8600 ("ARM: imx: temporarily remove CONFIG_SOC_FSL from LS1021A"). Therefore the driver can no longer be enabled on ARM platforms. This appears to be a mistake as arm64's ARCH_LAYERSCAPE and arm32 SOC_LS1021A SoCs use this symbol. It's enabled in these defconfigs: arch/arm/configs/imx_v6_v7_defconfig:CONFIG_USB_FSL_USB2=y arch/arm/configs/multi_v7_defconfig:CONFIG_USB_FSL_USB2=y arch/powerpc/configs/mgcoge_defconfig:CONFIG_USB_FSL_USB2=y arch/powerpc/configs/mpc512x_defconfig:CONFIG_USB_FSL_USB2=y To fix, expand the dependencies so USB_FSL_USB2 can be enabled on the ARM platforms, and with COMPILE_TEST. Fixes: a390bef7db1f ("usb: gadget: fsl_mxc_udc: Remove the driver") Signed-off-by: Joel Stanley <[email protected]> Link: https://lore.kernel.org/r/[email protected] Cc: stable <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
2021-06-10usb: typec: wcove: Use LE to CPU conversion when accessing msg->headerAndy Shevchenko1-1/+1
As LKP noticed the Sparse is not happy about strict type handling: .../typec/tcpm/wcove.c:380:50: sparse: expected unsigned short [usertype] header .../typec/tcpm/wcove.c:380:50: sparse: got restricted __le16 const [usertype] header Fix this by switching to use pd_header_cnt_le() instead of pd_header_cnt() in the affected code. Fixes: ae8a2ca8a221 ("usb: typec: Group all TCPCI/TCPM code together") Fixes: 3c4fb9f16921 ("usb: typec: wcove: start using tcpm for USB PD support") Reported-by: kernel test robot <[email protected]> Reviewed-by: Heikki Krogerus <[email protected]> Reviewed-by: Guenter Roeck <[email protected]> Signed-off-by: Andy Shevchenko <[email protected]> Link: https://lore.kernel.org/r/[email protected] Cc: stable <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
2021-06-10usb: typec: ucsi: Fix a comment in ucsi_init()Subbaraman Narayanamurthy1-1/+1
ucsi_unregister_ppm() got replaced with ucsi_unregister(). Fix the comment in ucsi_init() as well. Reviewed-by: Heikki Krogerus <[email protected]> Signed-off-by: Subbaraman Narayanamurthy <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2021-06-10USB: dwc3: remove debugfs root dentry storageGreg Kroah-Hartman3-7/+7
There is no need to keep around the debugfs "root" directory for the dwc3 device. Instead, look it up anytime we need to find it. This will help when callers get out-of-order and we had the potential to have a "stale" pointer around for the root dentry, as has happened in the past. Tested-by: Jack Pham <[email protected]> Reviewed-by: Peter Chen <[email protected]> Acked-by: Felipe Balbi <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2021-06-10usb: ehci: do not initialise static variablesJason Wang1-2/+2
Global static variables dont need to be initialised manully. Signed-off-by: Jason Wang <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2021-06-10USB: serial: cp210x: fix CP2102N-A01 modem controlJohan Hovold1-5/+59
CP2102N revision A01 (firmware version <= 1.0.4) has a buggy flow-control implementation that uses the ulXonLimit instead of ulFlowReplace field of the flow-control settings structure (erratum CP2102N_E104). A recent change that set the input software flow-control limits incidentally broke RTS control for these devices when CRTSCTS is not set as the new limits would always enable hardware flow control. Fix this by explicitly disabling flow control for the buggy firmware versions and only updating the input software flow-control limits when IXOFF is requested. This makes sure that the terminal settings matches the default zero ulXonLimit (ulFlowReplace) for these devices. Link: https://lore.kernel.org/r/[email protected] Reported-by: David Frey <[email protected]> Reported-by: Alex Villacís Lasso <[email protected]> Tested-by: Alex Villacís Lasso <[email protected]> Fixes: f61309d9c96a ("USB: serial: cp210x: set IXOFF thresholds") Cc: [email protected] # 5.12 Signed-off-by: Johan Hovold <[email protected]>
2021-06-10usb: cdns3: cdns3-gadget: Use list_move_tail instead of list_del/list_add_tailBaokun Li1-3/+1
Using list_move_tail() instead of list_del() + list_add_tail(). Reported-by: Hulk Robot <[email protected]> Signed-off-by: Baokun Li <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Peter Chen <[email protected]>
2021-06-10USB: serial: cp210x: fix alternate function for CP2102N QFN20Stefan Agner1-1/+19
The QFN20 part has a different GPIO/port function assignment. The configuration struct bit field ordered as TX/RX/RS485/WAKEUP/CLK which exactly matches GPIO0-3 for QFN24/28. However, QFN20 has a different GPIO to primary function assignment. Special case QFN20 to follow to properly detect which GPIOs are available. Signed-off-by: Stefan Agner <[email protected]> Link: https://lore.kernel.org/r/51830b2b24118eb0f77c5c9ac64ffb2f519dbb1d.1622218300.git.stefan@agner.ch Fixes: c8acfe0aadbe ("USB: serial: cp210x: implement GPIO support for CP2102N") Cc: [email protected] # 4.19 Signed-off-by: Johan Hovold <[email protected]>
2021-06-09usb: gadget: u_audio: add real feedback implementationRuslan Bilovol4-10/+134
This adds interface between userspace and feedback endpoint to report real feedback frequency to the Host. Current implementation adds new userspace interface ALSA mixer control "Capture Pitch 1000000" (similar to aloop driver's "PCM Rate Shift 100000" mixer control) Value in PPM is chosen to have correction value agnostic of the actual HW rate, which the application is not necessarily dealing with, while still retaining a good enough precision to allow smooth clock correction on the playback side, if necessary. Similar to sound/usb/endpoint.c, a slow down is allowed up to 25%. This has no impact on the required bandwidth. Speedup correction has an impact on the bandwidth reserved for the isochronous endpoint. The default allowed speedup is 500ppm. This seems to be more than enough but, if necessary, this is configurable through a module parameter. The reserved bandwidth is rounded up to the next packet size. Usage of this new control is easy to implement in existing userspace tools like alsaloop from alsa-utils. Signed-off-by: Ruslan Bilovol <[email protected]> Signed-off-by: Jerome Brunet <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2021-06-09usb: gadget: f_uac2: add adaptive sync support for captureRuslan Bilovol2-9/+93
Current f_uac2 USB OUT (aka 'capture') synchronization implements 'ASYNC' scenario which means USB Gadget has it's own freerunning clock and can update Host about real clock frequency through feedback endpoint so Host can align number of samples sent to the USB gadget to prevent overruns/underruns In case if Gadget can has no it's internal clock and can consume audio samples at any rate (for example, on the Gadget side someone records audio directly to a file, or audio samples are played through an external DAC as soon as they arrive), UAC2 spec suggests 'ADAPTIVE' synchronization type. Change UAC2 driver to make it configurable through additional 'c_sync' configfs file. Default remains 'asynchronous' with possibility to switch it to 'adaptive' Signed-off-by: Ruslan Bilovol <[email protected]> Signed-off-by: Jerome Brunet <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2021-06-09usb: gadget: f_uac2/u_audio: add feedback endpoint supportRuslan Bilovol3-3/+168
As per USB and UAC2 specs, asynchronous audio sink endpoint requires explicit synchronization mechanism (Isochronous Feedback Endpoint) Implement feedback companion endpoint for ISO OUT endpoint This patch adds all required infrastructure and USB requests handling for feedback endpoint. Syncrhonization itself is still dummy (feedback ep always reports 'nomimal frequency' e.g. no adjustement is needed). This satisfies hosts that require feedback endpoint (like Win10) and poll it periodically Actual synchronization mechanism should be implemented separately Signed-off-by: Ruslan Bilovol <[email protected]> Signed-off-by: Jerome Brunet <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2021-06-09usb: dwc2: Don't reset the core after setting turnaround timeClément Lassieur1-9/+21
Every time the hub signals a reset while we (device) are hsotg->connected, dwc2_hsotg_core_init_disconnected() is called, which in turn calls dwc2_hs_phy_init(). GUSBCFG.USBTrdTim is cleared upon Core Soft Reset, so if hsotg->params.phy_utmi_width is 8-bit, the value of GUSBCFG.USBTrdTim (the default one: 0x5, corresponding to 16-bit) is always different from hsotg->params.phy_utmi_width, thus dwc2_core_reset() is called every time (usbcfg != usbcfg_old), which causes 2 issues: 1) The call to dwc2_core_reset() does another reset 300us after the initial Chirp K of the first reset (which should last at least Tuch = 1ms), and messes up the High-speed Detection Handshake: both hub and device drive current into the D+ and D- lines at the same time. 2) GUSBCFG.USBTrdTim is cleared by the second reset, so its value is always the default one (0x5). Setting GUSBCFG.USBTrdTim after the potential call to dwc2_core_reset() fixes both issues. It is now set even when select_phy is false because the cost of the Core Soft Reset is removed. Fixes: 1e868545f2bb ("usb: dwc2: gadget: Move gadget phy init into core phy init") Signed-off-by: Clément Lassieur <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2021-06-09usb: gadget: f_fs: Fix setting of device and driver data cross-referencesAndrew Gabbasov1-33/+32
FunctionFS device structure 'struct ffs_dev' and driver data structure 'struct ffs_data' are bound to each other with cross-reference pointers 'ffs_data->private_data' and 'ffs_dev->ffs_data'. While the first one is supposed to be valid through the whole life of 'struct ffs_data' (and while 'struct ffs_dev' exists non-freed), the second one is cleared in 'ffs_closed()' (called from 'ffs_data_reset()' or the last 'ffs_data_put()'). This can be called several times, alternating in different order with 'ffs_free_inst()', that, if possible, clears the other cross-reference. As a result, different cases of these calls order may leave stale cross-reference pointers, used when the pointed structure is already freed. Even if it occasionally doesn't cause kernel crash, this error is reported by KASAN-enabled kernel configuration. For example, the case [last 'ffs_data_put()' - 'ffs_free_inst()'] was fixed by commit cdafb6d8b8da ("usb: gadget: f_fs: Fix use-after-free in ffs_free_inst"). The other case ['ffs_data_reset()' - 'ffs_free_inst()' - 'ffs_data_put()'] now causes KASAN reported error [1], when 'ffs_data_reset()' clears 'ffs_dev->ffs_data', then 'ffs_free_inst()' frees the 'struct ffs_dev', but can't clear 'ffs_data->private_data', which is then accessed in 'ffs_closed()' called from 'ffs_data_put()'. This happens since 'ffs_dev->ffs_data' reference is cleared too early. Moreover, one more use case, when 'ffs_free_inst()' is called immediately after mounting FunctionFS device (that is before the descriptors are written and 'ffs_ready()' is called), and then 'ffs_data_reset()' or 'ffs_data_put()' is called from accessing "ep0" file or unmounting the device. This causes KASAN error report like [2], since 'ffs_dev->ffs_data' is not yet set when 'ffs_free_inst()' can't properly clear 'ffs_data->private_data', that is later accessed to freed structure. Fix these (and may be other) cases of stale pointers access by moving setting and clearing of the mentioned cross-references to the single places, setting both of them when 'struct ffs_data' is created and bound to 'struct ffs_dev', and clearing both of them when one of the structures is destroyed. It seems convenient to make this pointer initialization and structures binding in 'ffs_acquire_dev()' and make pointers clearing in 'ffs_release_dev()'. This required some changes in these functions parameters and return types. Also, 'ffs_release_dev()' calling requires some cleanup, fixing minor issues, like (1) 'ffs_release_dev()' is not called if 'ffs_free_inst()' is called without unmounting the device, and "release_dev" callback is not called at all, or (2) "release_dev" callback is called before "ffs_closed" callback on unmounting, which seems to be not correctly nested with "acquire_dev" and "ffs_ready" callbacks. Make this cleanup togther with other mentioned 'ffs_release_dev()' changes. [1] ================================================================== root@rcar-gen3:~# mkdir /dev/cfs root@rcar-gen3:~# mkdir /dev/ffs root@rcar-gen3:~# modprobe libcomposite root@rcar-gen3:~# mount -t configfs none /dev/cfs root@rcar-gen3:~# mkdir /dev/cfs/usb_gadget/g1 root@rcar-gen3:~# mkdir /dev/cfs/usb_gadget/g1/functions/ffs.ffs [ 64.340664] file system registered root@rcar-gen3:~# mount -t functionfs ffs /dev/ffs root@rcar-gen3:~# cd /dev/ffs root@rcar-gen3:/dev/ffs# /home/root/ffs-test ffs-test: info: ep0: writing descriptors (in v2 format) [ 83.181442] read descriptors [ 83.186085] read strings ffs-test: info: ep0: writing strings ffs-test: dbg: ep1: starting ffs-test: dbg: ep2: starting ffs-test: info: ep1: starts ffs-test: info: ep2: starts ffs-test: info: ep0: starts ^C root@rcar-gen3:/dev/ffs# cd /home/root/ root@rcar-gen3:~# rmdir /dev/cfs/usb_gadget/g1/functions/ffs.ffs [ 98.935061] unloading root@rcar-gen3:~# umount /dev/ffs [ 102.734301] ================================================================== [ 102.742059] BUG: KASAN: use-after-free in ffs_release_dev+0x64/0xa8 [usb_f_fs] [ 102.749683] Write of size 1 at addr ffff0004d46ff549 by task umount/2997 [ 102.756709] [ 102.758311] CPU: 0 PID: 2997 Comm: umount Not tainted 5.13.0-rc4+ #8 [ 102.764971] Hardware name: Renesas Salvator-X board based on r8a77951 (DT) [ 102.772179] Call trace: [ 102.774779] dump_backtrace+0x0/0x330 [ 102.778653] show_stack+0x20/0x2c [ 102.782152] dump_stack+0x11c/0x1ac [ 102.785833] print_address_description.constprop.0+0x30/0x274 [ 102.791862] kasan_report+0x14c/0x1c8 [ 102.795719] __asan_report_store1_noabort+0x34/0x58 [ 102.800840] ffs_release_dev+0x64/0xa8 [usb_f_fs] [ 102.805801] ffs_fs_kill_sb+0x50/0x84 [usb_f_fs] [ 102.810663] deactivate_locked_super+0xa0/0xf0 [ 102.815339] deactivate_super+0x98/0xac [ 102.819378] cleanup_mnt+0xd0/0x1b0 [ 102.823057] __cleanup_mnt+0x1c/0x28 [ 102.826823] task_work_run+0x104/0x180 [ 102.830774] do_notify_resume+0x458/0x14e0 [ 102.835083] work_pending+0xc/0x5f8 [ 102.838762] [ 102.840357] Allocated by task 2988: [ 102.844032] kasan_save_stack+0x28/0x58 [ 102.848071] kasan_set_track+0x28/0x3c [ 102.852016] ____kasan_kmalloc+0x84/0x9c [ 102.856142] __kasan_kmalloc+0x10/0x1c [ 102.860088] __kmalloc+0x214/0x2f8 [ 102.863678] kzalloc.constprop.0+0x14/0x20 [usb_f_fs] [ 102.868990] ffs_alloc_inst+0x8c/0x208 [usb_f_fs] [ 102.873942] try_get_usb_function_instance+0xf0/0x164 [libcomposite] [ 102.880629] usb_get_function_instance+0x64/0x68 [libcomposite] [ 102.886858] function_make+0x128/0x1ec [libcomposite] [ 102.892185] configfs_mkdir+0x330/0x590 [configfs] [ 102.897245] vfs_mkdir+0x12c/0x1bc [ 102.900835] do_mkdirat+0x180/0x1d0 [ 102.904513] __arm64_sys_mkdirat+0x80/0x94 [ 102.908822] invoke_syscall+0xf8/0x25c [ 102.912772] el0_svc_common.constprop.0+0x150/0x1a0 [ 102.917891] do_el0_svc+0xa0/0xd4 [ 102.921386] el0_svc+0x24/0x34 [ 102.924613] el0_sync_handler+0xcc/0x154 [ 102.928743] el0_sync+0x198/0x1c0 [ 102.932238] [ 102.933832] Freed by task 2996: [ 102.937144] kasan_save_stack+0x28/0x58 [ 102.941181] kasan_set_track+0x28/0x3c [ 102.945128] kasan_set_free_info+0x28/0x4c [ 102.949435] ____kasan_slab_free+0x104/0x118 [ 102.953921] __kasan_slab_free+0x18/0x24 [ 102.958047] slab_free_freelist_hook+0x148/0x1f0 [ 102.962897] kfree+0x318/0x440 [ 102.966123] ffs_free_inst+0x164/0x2d8 [usb_f_fs] [ 102.971075] usb_put_function_instance+0x84/0xa4 [libcomposite] [ 102.977302] ffs_attr_release+0x18/0x24 [usb_f_fs] [ 102.982344] config_item_put+0x140/0x1a4 [configfs] [ 102.987486] configfs_rmdir+0x3fc/0x518 [configfs] [ 102.992535] vfs_rmdir+0x114/0x234 [ 102.996122] do_rmdir+0x274/0x2b0 [ 102.999617] __arm64_sys_unlinkat+0x94/0xc8 [ 103.004015] invoke_syscall+0xf8/0x25c [ 103.007961] el0_svc_common.constprop.0+0x150/0x1a0 [ 103.013080] do_el0_svc+0xa0/0xd4 [ 103.016575] el0_svc+0x24/0x34 [ 103.019801] el0_sync_handler+0xcc/0x154 [ 103.023930] el0_sync+0x198/0x1c0 [ 103.027426] [ 103.029020] The buggy address belongs to the object at ffff0004d46ff500 [ 103.029020] which belongs to the cache kmalloc-128 of size 128 [ 103.042079] The buggy address is located 73 bytes inside of [ 103.042079] 128-byte region [ffff0004d46ff500, ffff0004d46ff580) [ 103.054236] The buggy address belongs to the page: [ 103.059262] page:0000000021aa849b refcount:1 mapcount:0 mapping:0000000000000000 index:0xffff0004d46fee00 pfn:0x5146fe [ 103.070437] head:0000000021aa849b order:1 compound_mapcount:0 [ 103.076456] flags: 0x8000000000010200(slab|head|zone=2) [ 103.081948] raw: 8000000000010200 fffffc0013521a80 0000000d0000000d ffff0004c0002300 [ 103.090052] raw: ffff0004d46fee00 000000008020001e 00000001ffffffff 0000000000000000 [ 103.098150] page dumped because: kasan: bad access detected [ 103.103985] [ 103.105578] Memory state around the buggy address: [ 103.110602] ffff0004d46ff400: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb [ 103.118161] ffff0004d46ff480: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc [ 103.125726] >ffff0004d46ff500: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb [ 103.133284] ^ [ 103.139120] ffff0004d46ff580: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc [ 103.146679] ffff0004d46ff600: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb [ 103.154238] ================================================================== [ 103.161792] Disabling lock debugging due to kernel taint [ 103.167319] Unable to handle kernel paging request at virtual address 0037801d6000018e [ 103.175406] Mem abort info: [ 103.178457] ESR = 0x96000004 [ 103.181609] EC = 0x25: DABT (current EL), IL = 32 bits [ 103.187020] SET = 0, FnV = 0 [ 103.190185] EA = 0, S1PTW = 0 [ 103.193417] Data abort info: [ 103.196385] ISV = 0, ISS = 0x00000004 [ 103.200315] CM = 0, WnR = 0 [ 103.203366] [0037801d6000018e] address between user and kernel address ranges [ 103.210611] Internal error: Oops: 96000004 [#1] PREEMPT SMP [ 103.216231] Modules linked in: usb_f_fs libcomposite configfs ath9k_htc led_class mac80211 libarc4 ath9k_common ath9k_hw ath cfg80211 aes_ce_blk sata_rc4 [ 103.259233] CPU: 0 PID: 2997 Comm: umount Tainted: G B 5.13.0-rc4+ #8 [ 103.267031] Hardware name: Renesas Salvator-X board based on r8a77951 (DT) [ 103.273951] pstate: 00000005 (nzcv daif -PAN -UAO -TCO BTYPE=--) [ 103.280001] pc : ffs_data_clear+0x138/0x370 [usb_f_fs] [ 103.285197] lr : ffs_data_clear+0x124/0x370 [usb_f_fs] [ 103.290385] sp : ffff800014777a80 [ 103.293725] x29: ffff800014777a80 x28: ffff0004d7649c80 x27: 0000000000000000 [ 103.300931] x26: ffff800014777fb0 x25: ffff60009aec9394 x24: ffff0004d7649ca4 [ 103.308136] x23: 1fffe0009a3d063a x22: dfff800000000000 x21: ffff0004d1e831d0 [ 103.315340] x20: e1c000eb00000bb4 x19: ffff0004d1e83000 x18: 0000000000000000 [ 103.322545] x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000000 [ 103.329748] x14: 0720072007200720 x13: 0720072007200720 x12: 1ffff000012ef658 [ 103.336952] x11: ffff7000012ef658 x10: 0720072007200720 x9 : ffff800011322648 [ 103.344157] x8 : ffff800014777818 x7 : ffff80000977b2c7 x6 : 0000000000000000 [ 103.351359] x5 : 0000000000000001 x4 : ffff7000012ef659 x3 : 0000000000000001 [ 103.358562] x2 : 0000000000000000 x1 : 1c38001d6000018e x0 : e1c000eb00000c70 [ 103.365766] Call trace: [ 103.368235] ffs_data_clear+0x138/0x370 [usb_f_fs] [ 103.373076] ffs_data_reset+0x20/0x304 [usb_f_fs] [ 103.377829] ffs_data_closed+0x1ec/0x244 [usb_f_fs] [ 103.382755] ffs_fs_kill_sb+0x70/0x84 [usb_f_fs] [ 103.387420] deactivate_locked_super+0xa0/0xf0 [ 103.391905] deactivate_super+0x98/0xac [ 103.395776] cleanup_mnt+0xd0/0x1b0 [ 103.399299] __cleanup_mnt+0x1c/0x28 [ 103.402906] task_work_run+0x104/0x180 [ 103.406691] do_notify_resume+0x458/0x14e0 [ 103.410823] work_pending+0xc/0x5f8 [ 103.414351] Code: b4000a54 9102f280 12000802 d343fc01 (38f66821) [ 103.420490] ---[ end trace 57b43a50e8244f57 ]--- Segmentation fault root@rcar-gen3:~# ================================================================== [2] ================================================================== root@rcar-gen3:~# mkdir /dev/ffs root@rcar-gen3:~# modprobe libcomposite root@rcar-gen3:~# root@rcar-gen3:~# mount -t configfs none /dev/cfs root@rcar-gen3:~# mkdir /dev/cfs/usb_gadget/g1 root@rcar-gen3:~# mkdir /dev/cfs/usb_gadget/g1/functions/ffs.ffs [ 54.766480] file system registered root@rcar-gen3:~# mount -t functionfs ffs /dev/ffs root@rcar-gen3:~# rmdir /dev/cfs/usb_gadget/g1/functions/ffs.ffs [ 63.197597] unloading root@rcar-gen3:~# cat /dev/ffs/ep0 cat: read error:[ 67.213506] ================================================================== [ 67.222095] BUG: KASAN: use-after-free in ffs_data_clear+0x70/0x370 [usb_f_fs] [ 67.229699] Write of size 1 at addr ffff0004c26e974a by task cat/2994 [ 67.236446] [ 67.238045] CPU: 0 PID: 2994 Comm: cat Not tainted 5.13.0-rc4+ #8 [ 67.244431] Hardware name: Renesas Salvator-X board based on r8a77951 (DT) [ 67.251624] Call trace: [ 67.254212] dump_backtrace+0x0/0x330 [ 67.258081] show_stack+0x20/0x2c [ 67.261579] dump_stack+0x11c/0x1ac [ 67.265260] print_address_description.constprop.0+0x30/0x274 [ 67.271286] kasan_report+0x14c/0x1c8 [ 67.275143] __asan_report_store1_noabort+0x34/0x58 [ 67.280265] ffs_data_clear+0x70/0x370 [usb_f_fs] [ 67.285220] ffs_data_reset+0x20/0x304 [usb_f_fs] [ 67.290172] ffs_data_closed+0x240/0x244 [usb_f_fs] [ 67.295305] ffs_ep0_release+0x40/0x54 [usb_f_fs] [ 67.300256] __fput+0x304/0x580 [ 67.303576] ____fput+0x18/0x24 [ 67.306893] task_work_run+0x104/0x180 [ 67.310846] do_notify_resume+0x458/0x14e0 [ 67.315154] work_pending+0xc/0x5f8 [ 67.318834] [ 67.320429] Allocated by task 2988: [ 67.324105] kasan_save_stack+0x28/0x58 [ 67.328144] kasan_set_track+0x28/0x3c [ 67.332090] ____kasan_kmalloc+0x84/0x9c [ 67.336217] __kasan_kmalloc+0x10/0x1c [ 67.340163] __kmalloc+0x214/0x2f8 [ 67.343754] kzalloc.constprop.0+0x14/0x20 [usb_f_fs] [ 67.349066] ffs_alloc_inst+0x8c/0x208 [usb_f_fs] [ 67.354017] try_get_usb_function_instance+0xf0/0x164 [libcomposite] [ 67.360705] usb_get_function_instance+0x64/0x68 [libcomposite] [ 67.366934] function_make+0x128/0x1ec [libcomposite] [ 67.372260] configfs_mkdir+0x330/0x590 [configfs] [ 67.377320] vfs_mkdir+0x12c/0x1bc [ 67.380911] do_mkdirat+0x180/0x1d0 [ 67.384589] __arm64_sys_mkdirat+0x80/0x94 [ 67.388899] invoke_syscall+0xf8/0x25c [ 67.392850] el0_svc_common.constprop.0+0x150/0x1a0 [ 67.397969] do_el0_svc+0xa0/0xd4 [ 67.401464] el0_svc+0x24/0x34 [ 67.404691] el0_sync_handler+0xcc/0x154 [ 67.408819] el0_sync+0x198/0x1c0 [ 67.412315] [ 67.413909] Freed by task 2993: [ 67.417220] kasan_save_stack+0x28/0x58 [ 67.421257] kasan_set_track+0x28/0x3c [ 67.425204] kasan_set_free_info+0x28/0x4c [ 67.429513] ____kasan_slab_free+0x104/0x118 [ 67.434001] __kasan_slab_free+0x18/0x24 [ 67.438128] slab_free_freelist_hook+0x148/0x1f0 [ 67.442978] kfree+0x318/0x440 [ 67.446205] ffs_free_inst+0x164/0x2d8 [usb_f_fs] [ 67.451156] usb_put_function_instance+0x84/0xa4 [libcomposite] [ 67.457385] ffs_attr_release+0x18/0x24 [usb_f_fs] [ 67.462428] config_item_put+0x140/0x1a4 [configfs] [ 67.467570] configfs_rmdir+0x3fc/0x518 [configfs] [ 67.472626] vfs_rmdir+0x114/0x234 [ 67.476215] do_rmdir+0x274/0x2b0 [ 67.479710] __arm64_sys_unlinkat+0x94/0xc8 [ 67.484108] invoke_syscall+0xf8/0x25c [ 67.488055] el0_svc_common.constprop.0+0x150/0x1a0 [ 67.493175] do_el0_svc+0xa0/0xd4 [ 67.496671] el0_svc+0x24/0x34 [ 67.499896] el0_sync_handler+0xcc/0x154 [ 67.504024] el0_sync+0x198/0x1c0 [ 67.507520] [ 67.509114] The buggy address belongs to the object at ffff0004c26e9700 [ 67.509114] which belongs to the cache kmalloc-128 of size 128 [ 67.522171] The buggy address is located 74 bytes inside of [ 67.522171] 128-byte region [ffff0004c26e9700, ffff0004c26e9780) [ 67.534328] The buggy address belongs to the page: [ 67.539355] page:000000003177a217 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x5026e8 [ 67.549175] head:000000003177a217 order:1 compound_mapcount:0 [ 67.555195] flags: 0x8000000000010200(slab|head|zone=2) [ 67.560687] raw: 8000000000010200 fffffc0013037100 0000000c00000002 ffff0004c0002300 [ 67.568791] raw: 0000000000000000 0000000080200020 00000001ffffffff 0000000000000000 [ 67.576890] page dumped because: kasan: bad access detected [ 67.582725] [ 67.584318] Memory state around the buggy address: [ 67.589343] ffff0004c26e9600: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb [ 67.596903] ffff0004c26e9680: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc [ 67.604463] >ffff0004c26e9700: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb [ 67.612022] ^ [ 67.617860] ffff0004c26e9780: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc [ 67.625421] ffff0004c26e9800: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 67.632981] ================================================================== [ 67.640535] Disabling lock debugging due to kernel taint File descriptor[ 67.646100] Unable to handle kernel paging request at virtual address fabb801d4000018d in bad state [ 67.655456] Mem abort info: [ 67.659619] ESR = 0x96000004 [ 67.662801] EC = 0x25: DABT (current EL), IL = 32 bits [ 67.668225] SET = 0, FnV = 0 [ 67.671375] EA = 0, S1PTW = 0 [ 67.674613] Data abort info: [ 67.677587] ISV = 0, ISS = 0x00000004 [ 67.681522] CM = 0, WnR = 0 [ 67.684588] [fabb801d4000018d] address between user and kernel address ranges [ 67.691849] Internal error: Oops: 96000004 [#1] PREEMPT SMP [ 67.697470] Modules linked in: usb_f_fs libcomposite configfs ath9k_htc led_class mac80211 libarc4 ath9k_common ath9k_hw ath cfg80211 aes_ce_blk crypto_simd cryptd aes_ce_cipher ghash_ce gf128mul sha2_ce sha1_ce evdev sata_rcar libata xhci_plat_hcd scsi_mod xhci_hcd rene4 [ 67.740467] CPU: 0 PID: 2994 Comm: cat Tainted: G B 5.13.0-rc4+ #8 [ 67.748005] Hardware name: Renesas Salvator-X board based on r8a77951 (DT) [ 67.754924] pstate: 00000005 (nzcv daif -PAN -UAO -TCO BTYPE=--) [ 67.760974] pc : ffs_data_clear+0x138/0x370 [usb_f_fs] [ 67.766178] lr : ffs_data_clear+0x124/0x370 [usb_f_fs] [ 67.771365] sp : ffff800014767ad0 [ 67.774706] x29: ffff800014767ad0 x28: ffff800009cf91c0 x27: ffff0004c54861a0 [ 67.781913] x26: ffff0004dc90b288 x25: 1fffe00099ec10f5 x24: 00000000000a801d [ 67.789118] x23: 1fffe00099f6953a x22: dfff800000000000 x21: ffff0004cfb4a9d0 [ 67.796322] x20: d5e000ea00000bb1 x19: ffff0004cfb4a800 x18: 0000000000000000 [ 67.803526] x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000000 [ 67.810730] x14: 0720072007200720 x13: 0720072007200720 x12: 1ffff000028ecefa [ 67.817934] x11: ffff7000028ecefa x10: 0720072007200720 x9 : ffff80001132c014 [ 67.825137] x8 : ffff8000147677d8 x7 : ffff8000147677d7 x6 : 0000000000000000 [ 67.832341] x5 : 0000000000000001 x4 : ffff7000028ecefb x3 : 0000000000000001 [ 67.839544] x2 : 0000000000000005 x1 : 1abc001d4000018d x0 : d5e000ea00000c6d [ 67.846748] Call trace: [ 67.849218] ffs_data_clear+0x138/0x370 [usb_f_fs] [ 67.854058] ffs_data_reset+0x20/0x304 [usb_f_fs] [ 67.858810] ffs_data_closed+0x240/0x244 [usb_f_fs] [ 67.863736] ffs_ep0_release+0x40/0x54 [usb_f_fs] [ 67.868488] __fput+0x304/0x580 [ 67.871665] ____fput+0x18/0x24 [ 67.874837] task_work_run+0x104/0x180 [ 67.878622] do_notify_resume+0x458/0x14e0 [ 67.882754] work_pending+0xc/0x5f8 [ 67.886282] Code: b4000a54 9102f280 12000802 d343fc01 (38f66821) [ 67.892422] ---[ end trace 6d7cedf53d7abbea ]--- Segmentation fault root@rcar-gen3:~# ================================================================== Fixes: 4b187fceec3c ("usb: gadget: FunctionFS: add devices management code") Fixes: 3262ad824307 ("usb: gadget: f_fs: Stop ffs_closed NULL pointer dereference") Fixes: cdafb6d8b8da ("usb: gadget: f_fs: Fix use-after-free in ffs_free_inst") Reported-by: Bhuvanesh Surachari <[email protected]> Tested-by: Eugeniu Rosca <[email protected]> Reviewed-by: Eugeniu Rosca <[email protected]> Signed-off-by: Andrew Gabbasov <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2021-06-09usb: dwc3: support 64 bit DMA in platform driverSven Peter1-0/+4
Currently, the dwc3 platform driver does not explicitly ask for a DMA mask. This makes it fall back to the default 32-bit mask which breaks the driver on systems that only have RAM starting above the first 4G like the Apple M1 SoC. Fix this by calling dma_set_mask_and_coherent with a 64bit mask. Reviewed-by: Arnd Bergmann <[email protected]> Reviewed-by: Christoph Hellwig <[email protected]> Signed-off-by: Sven Peter <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2021-06-09USB: core: Avoid WARNings for 0-length descriptor requestsAlan Stern1-0/+6
The USB core has utility routines to retrieve various types of descriptors. These routines will now provoke a WARN if they are asked to retrieve 0 bytes (USB "receive" requests must not have zero length), so avert this by checking the size argument at the start. CC: Johan Hovold <[email protected]> Reported-and-tested-by: [email protected] Reviewed-by: Johan Hovold <[email protected]> Signed-off-by: Alan Stern <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2021-06-09usb: gadget: function: printer: use list_move instead of list_del/list_addBaokun Li1-2/+1
Using list_move() instead of list_del() + list_add(). Reported-by: Hulk Robot <[email protected]> Signed-off-by: Baokun Li <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2021-06-09usb: dwc3: core: fix kernel panic when do rebootPeter Chen1-1/+1
When do system reboot, it calls dwc3_shutdown and the whole debugfs for dwc3 has removed first, when the gadget tries to do deinit, and remove debugfs for its endpoints, it meets NULL pointer dereference issue when call debugfs_lookup. Fix it by removing the whole dwc3 debugfs later than dwc3_drd_exit. [ 2924.958838] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000002 .... [ 2925.030994] pstate: 60000005 (nZCv daif -PAN -UAO -TCO BTYPE=--) [ 2925.037005] pc : inode_permission+0x2c/0x198 [ 2925.041281] lr : lookup_one_len_common+0xb0/0xf8 [ 2925.045903] sp : ffff80001276ba70 [ 2925.049218] x29: ffff80001276ba70 x28: ffff0000c01f0000 x27: 0000000000000000 [ 2925.056364] x26: ffff800011791e70 x25: 0000000000000008 x24: dead000000000100 [ 2925.063510] x23: dead000000000122 x22: 0000000000000000 x21: 0000000000000001 [ 2925.070652] x20: ffff8000122c6188 x19: 0000000000000000 x18: 0000000000000000 [ 2925.077797] x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000004 [ 2925.084943] x14: ffffffffffffffff x13: 0000000000000000 x12: 0000000000000030 [ 2925.092087] x11: 0101010101010101 x10: 7f7f7f7f7f7f7f7f x9 : ffff8000102b2420 [ 2925.099232] x8 : 7f7f7f7f7f7f7f7f x7 : feff73746e2f6f64 x6 : 0000000000008080 [ 2925.106378] x5 : 61c8864680b583eb x4 : 209e6ec2d263dbb7 x3 : 000074756f307065 [ 2925.113523] x2 : 0000000000000001 x1 : 0000000000000000 x0 : ffff8000122c6188 [ 2925.120671] Call trace: [ 2925.123119] inode_permission+0x2c/0x198 [ 2925.127042] lookup_one_len_common+0xb0/0xf8 [ 2925.131315] lookup_one_len_unlocked+0x34/0xb0 [ 2925.135764] lookup_positive_unlocked+0x14/0x50 [ 2925.140296] debugfs_lookup+0x68/0xa0 [ 2925.143964] dwc3_gadget_free_endpoints+0x84/0xb0 [ 2925.148675] dwc3_gadget_exit+0x28/0x78 [ 2925.152518] dwc3_drd_exit+0x100/0x1f8 [ 2925.156267] dwc3_remove+0x11c/0x120 [ 2925.159851] dwc3_shutdown+0x14/0x20 [ 2925.163432] platform_shutdown+0x28/0x38 [ 2925.167360] device_shutdown+0x15c/0x378 [ 2925.171291] kernel_restart_prepare+0x3c/0x48 [ 2925.175650] kernel_restart+0x1c/0x68 [ 2925.179316] __do_sys_reboot+0x218/0x240 [ 2925.183247] __arm64_sys_reboot+0x28/0x30 [ 2925.187262] invoke_syscall+0x48/0x100 [ 2925.191017] el0_svc_common.constprop.0+0x48/0xc8 [ 2925.195726] do_el0_svc+0x28/0x88 [ 2925.199045] el0_svc+0x20/0x30 [ 2925.202104] el0_sync_handler+0xa8/0xb0 [ 2925.205942] el0_sync+0x148/0x180 [ 2925.209270] Code: a9025bf5 2a0203f5 121f0056 370802b5 (79400660) [ 2925.215372] ---[ end trace 124254d8e485a58b ]--- [ 2925.220012] Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b [ 2925.227676] Kernel Offset: disabled [ 2925.231164] CPU features: 0x00001001,20000846 [ 2925.235521] Memory Limit: none [ 2925.238580] ---[ end Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b ]--- Fixes: 5ff90af9da8f ("usb: dwc3: debugfs: Add and remove endpoint dirs dynamically") Cc: Jack Pham <[email protected]> Tested-by: Jack Pham <[email protected]> Signed-off-by: Peter Chen <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2021-06-09usb: misc: brcmstb-usb-pinmap: check return value after calling ↵Yang Yingliang1-0/+2
platform_get_resource() It will cause null-ptr-deref if platform_get_resource() returns NULL, we need check the return value. Fixes: 517c4c44b323 ("usb: Add driver to allow any GPIO to be used for 7211 USB signals") Cc: stable <[email protected]> Signed-off-by: Yang Yingliang <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2021-06-09usb: dwc3: ep0: fix NULL pointer exceptionMarian-Cristian Rotariu1-0/+3
There is no validation of the index from dwc3_wIndex_to_dep() and we might be referring a non-existing ep and trigger a NULL pointer exception. In certain configurations we might use fewer eps and the index might wrongly indicate a larger ep index than existing. By adding this validation from the patch we can actually report a wrong index back to the caller. In our usecase we are using a composite device on an older kernel, but upstream might use this fix also. Unfortunately, I cannot describe the hardware for others to reproduce the issue as it is a proprietary implementation. [ 82.958261] Unable to handle kernel NULL pointer dereference at virtual address 00000000000000a4 [ 82.966891] Mem abort info: [ 82.969663] ESR = 0x96000006 [ 82.972703] Exception class = DABT (current EL), IL = 32 bits [ 82.978603] SET = 0, FnV = 0 [ 82.981642] EA = 0, S1PTW = 0 [ 82.984765] Data abort info: [ 82.987631] ISV = 0, ISS = 0x00000006 [ 82.991449] CM = 0, WnR = 0 [ 82.994409] user pgtable: 4k pages, 39-bit VAs, pgdp = 00000000c6210ccc [ 83.000999] [00000000000000a4] pgd=0000000053aa5003, pud=0000000053aa5003, pmd=0000000000000000 [ 83.009685] Internal error: Oops: 96000006 [#1] PREEMPT SMP [ 83.026433] Process irq/62-dwc3 (pid: 303, stack limit = 0x000000003985154c) [ 83.033470] CPU: 0 PID: 303 Comm: irq/62-dwc3 Not tainted 4.19.124 #1 [ 83.044836] pstate: 60000085 (nZCv daIf -PAN -UAO) [ 83.049628] pc : dwc3_ep0_handle_feature+0x414/0x43c [ 83.054558] lr : dwc3_ep0_interrupt+0x3b4/0xc94 ... [ 83.141788] Call trace: [ 83.144227] dwc3_ep0_handle_feature+0x414/0x43c [ 83.148823] dwc3_ep0_interrupt+0x3b4/0xc94 [ 83.181546] ---[ end trace aac6b5267d84c32f ]--- Signed-off-by: Marian-Cristian Rotariu <[email protected]> Cc: stable <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2021-06-09usb: gadget: eem: fix wrong eem header operationLinyu Yuan1-2/+2
when skb_clone() or skb_copy_expand() fail, it should pull skb with lengh indicated by header, or not it will read network data and check it as header. Cc: <[email protected]> Signed-off-by: Linyu Yuan <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2021-06-09usb: typec: intel_pmc_mux: Put ACPI device using acpi_dev_put()Andy Shevchenko1-4/+4
For ACPI devices we have a symmetric API to put them, so use it in the driver. Reviewed-by: Heikki Krogerus <[email protected]> Signed-off-by: Andy Shevchenko <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2021-06-09usb: typec: intel_pmc_mux: Add missed error check for devm_ioremap_resource()Andy Shevchenko1-0/+5
devm_ioremap_resource() can return an error, add missed check for it. Fixes: 43d596e32276 ("usb: typec: intel_pmc_mux: Check the port status before connect") Reviewed-by: Heikki Krogerus <[email protected]> Signed-off-by: Andy Shevchenko <[email protected]> Cc: stable <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2021-06-09usb: typec: intel_pmc_mux: Put fwnode in error case during ->probe()Andy Shevchenko1-1/+3
device_get_next_child_node() bumps a reference counting of a returned variable. We have to balance it whenever we return to the caller. Fixes: 6701adfa9693 ("usb: typec: driver for Intel PMC mux control") Cc: Heikki Krogerus <[email protected]> Reviewed-by: Heikki Krogerus <[email protected]> Signed-off-by: Andy Shevchenko <[email protected]> Cc: stable <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2021-06-09usb: typec: tcpm: Do not finish VDM AMS for retrying ResponsesKyle Tso1-0/+3
If the VDM responses couldn't be sent successfully, it doesn't need to finish the AMS until the retry count reaches the limit. Fixes: 0908c5aca31e ("usb: typec: tcpm: AMS and Collision Avoidance") Reviewed-by: Guenter Roeck <[email protected]> Cc: stable <[email protected]> Acked-by: Heikki Krogerus <[email protected]> Signed-off-by: Kyle Tso <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2021-06-09usb: fix various gadget panics on 10gbps cablingMaciej Żenczykowski1-0/+8
usb_assign_descriptors() is called with 5 parameters, the last 4 of which are the usb_descriptor_header for: full-speed (USB1.1 - 12Mbps [including USB1.0 low-speed @ 1.5Mbps), high-speed (USB2.0 - 480Mbps), super-speed (USB3.0 - 5Gbps), super-speed-plus (USB3.1 - 10Gbps). The differences between full/high/super-speed descriptors are usually substantial (due to changes in the maximum usb block size from 64 to 512 to 1024 bytes and other differences in the specs), while the difference between 5 and 10Gbps descriptors may be as little as nothing (in many cases the same tuning is simply good enough). However if a gadget driver calls usb_assign_descriptors() with a NULL descriptor for super-speed-plus and is then used on a max 10gbps configuration, the kernel will crash with a null pointer dereference, when a 10gbps capable device port + cable + host port combination shows up. (This wouldn't happen if the gadget max-speed was set to 5gbps, but it of course defaults to the maximum, and there's no real reason to artificially limit it) The fix is to simply use the 5gbps descriptor as the 10gbps descriptor, if a 10gbps descriptor wasn't provided. Obviously this won't fix the problem if the 5gbps descriptor is also NULL, but such cases can't be so trivially solved (and any such gadgets are unlikely to be used with USB3 ports any way). Cc: Felipe Balbi <[email protected]> Cc: Greg Kroah-Hartman <[email protected]> Signed-off-by: Maciej Żenczykowski <[email protected]> Cc: stable <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
Powered by cgit, Gruvboxed by Blaster4385.