Age | Commit message (Collapse) | Author | Files | Lines |
|
While in source mode, vbus could be shutoff by protections
circuits. TCPM does not move back to toggling state to
re-initiate connection. Fix this by moving to SRC_UNATTACHED
state when vbus shuts off while in source mode.
Reviewed-by: Guenter Roeck <[email protected]>
Reviewed-by: Heikki Krogerus <[email protected]>
Signed-off-by: Badhri Jagan Sridharan <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The driver core ignores the return value of struct device_driver::remove
because there is only little that can be done. To simplify the quest to
make this function return void, let struct sa1111_driver::remove return
void, too. All users already unconditionally return 0, this commit makes
it obvious that returning an error code is a bad idea and ensures future
users behave accordingly.
Link: https://lore.kernel.org/r/[email protected]
Acked-by: Dmitry Torokhov <[email protected]>
Reviewed-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Uwe Kleine-König <[email protected]>
Signed-off-by: Russell King <[email protected]>
|
|
The partner's PD revision may be resolved later than the port partner
registration since the port partner creation may take place once
Type-C detects the port has changed state, but before PD communication is
completed.
Add a setter so that the partner's PD revision can be attached to it once
it becomes available.
If the revision is set to a valid version (not 0), the setter will also
refresh the partner's usb_pd flag and notify on "supports_usb_power_delivery"
sysfs property as well.
Reviewed-by: Heikki Krogerus <[email protected]>
Signed-off-by: Benson Leung <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The USB Power Delivery specification Section 6.2.1.1.5 outlines
revision backward compatibility requirements starting from Revision 3.0.
The Port, the Cable Plug, and the Port Partner may support either
revision 2 or revision 3 independently, and communication between ports,
partners, and cables of different revisions are allowed under rules
that the parties agree to communicate between each other using the
lowest common operating revision.
This may mean that Port-to-Partner operating revision comms may be
different than Port-to-CablePlug operating revision comms. For example,
it is possible for a R3.0 port to communicate with a R3.0 partner
using R3.0 messages, while the R3.0 port (in the same session) must
communicate with the R2.0 cable using R2.0 messages only.
Introduce individual revision number properties for cable
and port partner so that the port can track them independently.
Reviewed-by: Heikki Krogerus <[email protected]>
Signed-off-by: Benson Leung <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The Type-C Revision was in a specific BCD format "0120H" for 1.2.
USB PD revision numbers follow a similar pattern with "0300H" for 3.0.
Standardizes the sysfs format for usb_power_delivery_revision
to align with the BCD format used for usb_typec_revision.
Example values:
- "2.0": USB Power Delivery Release 2.0
- "3.0": USB Power Delivery Release 3.0
- "3.1": USB Power Delivery Release 3.1
Reviewed-by: Heikki Krogerus <[email protected]>
Signed-off-by: Benson Leung <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
For those unchecked endpoints, we don't allocate bandwidth for
them, so no need free the bandwidth, otherwise will decrease
the allocated bandwidth.
Meanwhile use xhci_dbg() instead of dev_dbg() to print logs and
rename bw_ep_list_new as bw_ep_chk_list.
Fixes: 1d69f9d901ef ("usb: xhci-mtk: fix unreleased bandwidth data")
Cc: stable <[email protected]>
Reviewed-and-tested-by: Ikjoon Jang <[email protected]>
Signed-off-by: Chunfeng Yun <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Should clear the pipe running flag in usbhs_pkt_pop(). Otherwise,
we cannot use this pipe after dequeue was called while the pipe was
running.
Fixes: 8355b2b3082d ("usb: renesas_usbhs: fix the behavior of some usbhs_pkt_handle")
Reported-by: Tho Vu <[email protected]>
Signed-off-by: Yoshihiro Shimoda <[email protected]>
Link: https://lore.kernel.org/r/1612183640-8898-1-git-send-email-yoshihiro.shimoda.uh@renesas.com
Cc: stable <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Add back a few explanatory comments related to the divisor encoding
which got lost in a coding-style clean up many years ago.
Signed-off-by: Johan Hovold <[email protected]>
|
|
The most-significant bit of the sub-integer-prescaler index is set in
the high byte of the baudrate request wIndex also for FTX devices.
This fixes rates like 1152000 which got mapped to 1.2 MBd.
Reported-by: Vladimir <[email protected]>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=210351
Cc: [email protected]
Signed-off-by: Johan Hovold <[email protected]>
|
|
Clear the RTS bits of the flow-control request before determining the
new value when updating the settings.
Signed-off-by: Johan Hovold <[email protected]>
|
|
Clearing TIOCM_RTS should always deassert RTS and setting the same bit
should enable auto-RTS if hardware flow control is enabled.
This allows user space to throttle input directly at the source also
when hardware-assisted flow control is enabled and makes dtr_rts()
always deassert both lines during close (when HUPCL is set).
Signed-off-by: Johan Hovold <[email protected]>
|
|
Use the 0-flag and a field width to specify zero-padding consistently in
printk messages.
Signed-off-by: Johan Hovold <[email protected]>
|
|
Shorten the flow-control debug message by abbreviating the field names
and reducing the value width to two characters. The latter improves
readability since all but the least significant byte will almost always
be zero anyway.
Signed-off-by: Johan Hovold <[email protected]>
|
|
Drop the macros used to shift the flow-control settings to make the code
more readable for consistency with the other requests.
Signed-off-by: Johan Hovold <[email protected]>
|
|
The vendor request used to set the flow-control settings also sets the
state of the modem-control lines.
Add state variables to keep track of the modem-control lines to avoid
always asserting the lines whenever the flow-control settings are
updated.
This specifically also avoids asserting DTR/RTS when opening a port with
the line speed set to B0.
Signed-off-by: Johan Hovold <[email protected]>
|
|
The CP210X_SET_MHS request cannot be used to control RTS when hardware
flow control (auto-RTS) is enabled and instead returns an error which is
currently logged as:
cp210x ttyUSB0: failed set request 0x7 status: -32
when opening and closing a port (and on TIOCMSET requests).
Add a crtscts flag to keep track of the hardware flow-control setting
and use it to suppress any request to change RTS when auto-RTS is
enabled.
Note that RTS is still deasserted when disabling the UART as part of
close.
Reported-by: Pho Tran <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
This code should return -ENOMEM if the allocation fails but it currently
returns success.
Fixes: 9b95236eebdb ("usb: gadget: ether: allocate and init otg descriptor by otg capabilities")
Signed-off-by: Dan Carpenter <[email protected]>
Link: https://lore.kernel.org/r/YBKE9rqVuJEOUWpW@mwanda
Cc: stable <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 5.11-rc6
Here are some new device-ids for 5.11-rc6.
All but the option one have been in linux-next, and with no reported
issues.
* tag 'usb-serial-5.11-rc6' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: Adding support for Cinterion MV31
USB: serial: cp210x: add pid/vid for WSDA-200-USB
USB: serial: cp210x: add new VID/PID for supporting Teraoka AD2000
|
|
If we receive a transfer event indicating that an endpoint should be
halted, but current endpoint state doesn't match it, then the halt might
be just resolved by the stop endpoint completion handler that detects the
halted endpoint due to a context state error.
In this case the TD we halted on is already moved to the cancelled TD list,
and should not be successfully completed and given back anymore.
Let the stop endpoint completion handler reset the endpoint, and then let
the reset endpoint handler give back the cancelled TD among all other
ones on the cancelled TD list
Signed-off-by: Mathias Nyman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
A halted endpoint can be detected both when transfer events complete, and
in stop endpoint command completion. Both these handlers will start
clearing up the halted endpoint and queue a reset endpoint command.
It's possible to get both events for the same halted endpoint if right
after a URB cancel queues a stop endpoint command the endpoint stalls.
Use the EP_HALTED flag to prevent resetting the endpoint twice.
Signed-off-by: Mathias Nyman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
xhci_find_new_dequeue_state() and xhci_queue_new_dequeue_state() are no
longer used afer introducing the move_dequeue_past_td() function.
also remove struct xhci_dequeue_state as its no longer used.
Signed-off-by: Mathias Nyman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Replace xhci_find_new_dequeue_state() and xhci_queue_new_dequeue_state()
functions with one combined function.
These function were always called after each other, and had a lot of extra
code just to pass the newly found dequeue state from the first function
to the other.
The new function also returns error in case there is a failure to
queue the new dequeue state. This way the caller can decide on
recovery measures to handle it.
Signed-off-by: Mathias Nyman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Handle race where a stop endpoint command fails with "context state error"
as hardware hasn't actually started the ring yet after a previous urb
cancellation completed and restarted the endpoint.
Flushing the doorbell write that restart the endpoint reduced these cases,
but didn't completely resolve them.
Check if the ring is running in the stop endpoint completion handler, and
issue a new stop endpoint command in this case.
Signed-off-by: Mathias Nyman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
xhci 4.6.9: "A busy endpoint may asynchronously transition from the
Running to the Halted or Error state due to error conditions detected
while processing TRBs. A possible race condition may occur if software,
thinking an endpoint is in the running state, issues a Stop Endpoint
Command, however at the same time the xHC asynchronously transitions
the endpoint to the Halted or Error state. In this case, a Context
State Error may be generated for the command completion. Software
may verify that this case occurred by inspecting the EP State for
Halted or Error when a Stop Endpoint Command results in a Context
State Error."
Halted endpoints were not detected or handled at all in the stop endpoint
completion handler. A set TR Deq ptr command was bluntly queued instead
of resetting the endpoint first. The set TR Deq command would fail with
a context state error.
Fix this case by resetting the halted endpoint first to get it to a
stopped state instead of the halted (error) state.
Handle cancelled TDs once endpoint reset completes,
invalidating cancelled TDs on ring either by turning them to no-op,
or in case ring stopped on cancelled TD then move hardware dequeue pointer
past it, which will clear the cancelled TD from hw cache, and make sure
HW does not process it
Signed-off-by: Mathias Nyman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Don't queue both a reset endpoint command and a
set TR deq command at once when handling a halted endpoint.
split this into two steps.
Initially only queue a reset endpoint command, and then if needed queue a
set TR deq command in the reset endpoint handler.
Note: This removes the RESET_EP_QUIRK handling which was added in
commit ac9d8fe7c6a8 ("USB: xhci: Add quirk for Fresco Logic xHCI hardware.")
This quirk was added in 2009 for prototype xHCI hardware meant for
evaluation purposes only, and should not reach consumers.
This hardware could not handle two commands queued at once, and had
bad data in the output context after a reset endpoint command.
After this patch two command are no longer queued at once, so that
part is solved in this rewrite, but the workaround for bad data in the
output context solved by issuing an extra configure endpoint command is
bluntly removed.
Adding this workaround to the new rewrite just adds complexity, and I
think it's time to let this quirk go.
Print a debug message instead.
Signed-off-by: Mathias Nyman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Halted endpoints can be discoverd both when handling transfer events and
command completion events. Move code that handles halted endpoints before
both of those event handlers.
Rename the function to xhci_handle_halted_ep() to better describe
what it does. Try to reserve "cleanup" word in function names for last
stage cleanup activities.
No functional changes
Signed-off-by: Mathias Nyman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Refactor handler for stop endpoint command completion. Yank out the part
that invalidates cancelled TDs and turn it into a separate function.
Invalidating cancelled TDs should be done while the ring is stopped,
but not exclusively in the stop endpoint command completeion handler.
We will need to invalidate TDs after resetting endpoints as well.
Signed-off-by: Mathias Nyman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
In cases where the TD can't be given back in current handler we want
to be able to store it until its time to return the TD.
Signed-off-by: Mathias Nyman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
use the existing xhci_td_cleanup() to give back cancelled TDs when a
ring is stopped.
A minor change to make sure we don't try to remove an already removed
td from the list is needed as cancelled TDs are already removed from the
td_list immediatelty when it's cancelled.
Signed-off-by: Mathias Nyman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
No funtional changes
Signed-off-by: Mathias Nyman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Create a separate helper function to issue reset endpont commands
to clear halted endpoints.
This is useful for cases where a halted endpoint is discovered while
completing another command, and the endpoint halt needs to be cleared
with a endpoint reset first.
No functional changes
Signed-off-by: Mathias Nyman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Stop endpoint command fails with "context state error" if the endpoint is
already stopped.
This case was observed when a previous URB cancel had just completed and
rang the doorbell to restart the ring, when a new URB cancel queued a stop
endpoint command.
>From xHC hardware pov the endpoint had not yet started, so the stop
endpoint command failed with context state error.
Right after this the doorbell ring took effect and ring was restarted.
Interrupt handler saw a stop endpoint command completion event with
"context state error" and discovered that the ring was back up in
running state.
flushing the write reduces these cases in stress testing, but does not
completely remove the issue.
Signed-off-by: Mathias Nyman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
xhci driver relies on link TRBs existing in the correct places in TRB
ring buffers shared with the host controller.
The controller should not modify these link TRBs, but in theory a faulty
xHC could do it.
Add some basic sanity checks to avoid infinite loops in interrupt handler,
or accessing unallocated memory outside a ring segment due to missing or
misplaced link TRBs.
Signed-off-by: Mathias Nyman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Instead of re-reading, masking and endianness correcting the same trb
several times to get the trb type from an event, just do it once and
store it in a local variable.
Also pass the trb_type directly to the vendor specific event handler,
avoiding one more similar read.
In addition to the security benefit this also cleans up the code
and helps readability.
Signed-off-by: Mathias Nyman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
When finishing a TD we walk the endpoint dequeue trb pointer
until it matches the last TRB of the TD.
TDs can contain over 100 TRBs, meaning we call a function 100 times,
do a few comparisons and increase a couple values for each of these calls,
all in interrupt context.
This can all be avoided by adding a pointer to the last TRB segment, and
a number of TRBs in the TD. So instead of walking through each TRB just
set the new dequeue segment, pointer, and number of free TRBs directly.
Getting rid of the while loop also reduces the risk of getting stuck in a
infinite loop in the interrupt handler. Loop relied on valid matching
dequeue and last_trb values to break.
Signed-off-by: Mathias Nyman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Check that the slot_id that we dug out from command completion event
TRB, is valid before using it to identify the slot associated with the
command that generated the event.
Signed-off-by: Lalithambika Krishna Kumar <[email protected]>
Signed-off-by: Mathias Nyman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
xhci driver links together segments in a ring buffer by turning the last
TRB of a segment into a link TRB, pointing to the beginning of
the next segment.
If the first TRB of every segment for some unknown reason is a link TRB
pointing to the next segment, then prepare_ring() loops indefinitely.
This isn't something the xhci driver would do.
xHC hardware has access to these rings, it sholdn't be writing link
TRBs either, but with broken xHC hardware this could in theory be
possible.
Signed-off-by: Mathias Nyman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The one case that used this function can use the
xhci_triad_to_transfer_ring() helper instead.
Avoid having several functions doing basically the same thing.
Signed-off-by: Mathias Nyman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Two existing ring helpers, xhci_triad_to_transfer_ring() and
xhci_stream_id_to_ring() have partially similar functionality.
Both have some limitation, especieally with boundary checking.
Add a new xhci_virt_ep_to_ring() helper with proper boundary checking
that can replace parts of one helper, and later will completely
replace the other helper.
Signed-off-by: Mathias Nyman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Check that the xhci_virt_dev structure that we dug out based
on a slot_id value from a command completion is valid before
dereferencing it.
Signed-off-by: Mathias Nyman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
In several event handlers we need to find the right endpoint
structure from slot_id and ep_index in the event.
Add a helper for this, check that slot_id and ep_index are valid.
Signed-off-by: Mathias Nyman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
several command completion handlers are passed the event trb
as a paramtere even if it't not used.
Remove it.
Signed-off-by: Mathias Nyman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Instead of passing slot id and endpoint index to
cleanup_halted_endpoint() pass the endpoint structure pointer
as it's already known.
Avoids again digging out the endpoint structure based on
slot id and endpoint index, and passing them along the
call chain for this purpose only.
Add slot_id to the virt_dev structure so that it
can easily be found from a virt_dev, or its child, the
virt_ep endpoint structure.
Signed-off-by: Mathias Nyman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
isochronous endpoints do not support streams, meaning that
there is only one ring per endpoint.
Avoid double-fetching the transfer event DMA to get the
ring. Also makes passing the event to skip_isoc_td() uncecessary.
Signed-off-by: Mathias Nyman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
When handling transfer events the event is passed along the handling
callpath and parsed again in several occasions.
The event contains slot_id and endpoint index, from which the driver
endpoint structure can be found. There wasn't however a way to get the
endpoint index or parent usb device from this endpoint structure.
A lot of extra event parsing, and thus some DMA doublefetch cases,
and excess variables and code can be avoided by adding endpoint index
and parent usb virt device pointer to the endpoint structure.
Signed-off-by: Mathias Nyman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
This code should return -ENOMEM if the kmalloc() fails but instead
it returns success.
Signed-off-by: Dan Carpenter <[email protected]>
Fixes: 0f64478cbc7a ("USB: add USB serial mos7720 driver")
Cc: [email protected]
Signed-off-by: Johan Hovold <[email protected]>
|
|
Adding support for Cinterion device MV31 for enumeration with
PID 0x00B3 and 0x00B7.
usb-devices output for 0x00B3
T: Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 6 Spd=5000 MxCh= 0
D: Ver= 3.20 Cls=ef(misc ) Sub=02 Prot=01 MxPS= 9 #Cfgs= 1
P: Vendor=1e2d ProdID=00b3 Rev=04.14
S: Manufacturer=Cinterion
S: Product=Cinterion PID 0x00B3 USB Mobile Broadband
S: SerialNumber=b3246eed
C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=896mA
I: If#=0x0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
I: If#=0x1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I: If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#=0x3 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=ff Driver=cdc_wdm
I: If#=0x4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#=0x5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
usb-devices output for 0x00B7
T: Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 5 Spd=5000 MxCh= 0
D: Ver= 3.20 Cls=ef(misc ) Sub=02 Prot=01 MxPS= 9 #Cfgs= 1
P: Vendor=1e2d ProdID=00b7 Rev=04.14
S: Manufacturer=Cinterion
S: Product=Cinterion PID 0x00B3 USB Mobile Broadband
S: SerialNumber=b3246eed
C: #Ifs= 4 Cfg#= 1 Atr=a0 MxPwr=896mA
I: If#=0x0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I: If#=0x1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#=0x3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
Signed-off-by: Christoph Schemmel <[email protected]>
Cc: [email protected]
Signed-off-by: Johan Hovold <[email protected]>
|
|
Use the more modern API here instead of using of_match_device() and
avoid casting away const from the returned pointer by pushing the const
type through to the users. This nicely avoids referencing the match
table when it is undefined with configurations where CONFIG_OF=n and
avoids const issues.
Signed-off-by: Stephen Boyd <[email protected]>
Acked-by: Greg Kroah-Hartman <[email protected]>
Cc: Arnd Bergmann <[email protected]>
Cc: Geert Uytterhoeven <[email protected]>
Cc: Richard Leitner <[email protected]>
Cc: Greg Kroah-Hartman <[email protected]>
Cc: Rob Herring <[email protected]>
Cc: Frank Rowand <[email protected]>
Cc: <[email protected]>
Signed-off-by: Rob Herring <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
With some USB network adapters, such as DM96xx, the following message
is seen for each maximum size receive packet.
dwc2 ff540000.usb: dwc2_update_urb_state(): trimming xfer length
This happens because the packet size requested by the driver is 1522
bytes, wMaxPacketSize is 64, the dwc2 driver configures the chip to
receive 24*64 = 1536 bytes, and the chip does indeed send more than
1522 bytes of data. Since the event does not indicate an error condition,
the message is just noise. Demote it to debug level.
Fixes: 7359d482eb4d3 ("staging: HCD files for the DWC2 driver")
Tested-by: Nicolas Saenz Julienne <[email protected]>
Reviewed-by: Douglas Anderson <[email protected]>
Signed-off-by: Guenter Roeck <[email protected]>
Signed-off-by: Nicolas Saenz Julienne <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
In some situations, the following error messages are reported.
dwc2 ff540000.usb: dwc2_hc_chhltd_intr_dma: Channel 1 - ChHltd set, but reason is unknown
dwc2 ff540000.usb: hcint 0x00000002, intsts 0x04000021
This is sometimes followed by:
dwc2 ff540000.usb: dwc2_update_urb_state_abn(): trimming xfer length
and then:
WARNING: CPU: 0 PID: 0 at kernel/v4.19/drivers/usb/dwc2/hcd.c:2913
dwc2_assign_and_init_hc+0x98c/0x990
The warning suggests that an odd buffer address is to be used for DMA.
After an error is observed, the receive buffer may be full
(urb->actual_length >= urb->length). However, the urb is still left in
the queue unless three errors were observed in a row. When it is queued
again, the dwc2 hcd code translates this into a 1-block transfer.
If urb->actual_length (ie the total expected receive length) is not
DMA-aligned, the buffer pointer programmed into the chip will be
unaligned. This results in the observed warning.
To solve the problem, abort input transactions after an error with
unknown cause if the entire packet was already received. This may be
a bit drastic, but we don't really know why the transfer was aborted
even though the entire packet was received. Aborting the transfer in
this situation is less risky than accepting a potentially corrupted
packet.
With this patch in place, the 'ChHltd set' and 'trimming xfer length'
messages are still observed, but there are no more transfer attempts
with odd buffer addresses.
Fixes: 151d0cbdbe860 ("usb: dwc2: make the scheduler handle excessive NAKs better")
Cc: Boris ARZUR <[email protected]>
Cc: Douglas Anderson <[email protected]>
Tested-by: Nicolas Saenz Julienne <[email protected]>
Reviewed-by: Douglas Anderson <[email protected]>
Signed-off-by: Guenter Roeck <[email protected]>
Signed-off-by: Nicolas Saenz Julienne <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|