| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
These ioctls never reach driver's ->ioctl() - tty_ioctl() handles
them on its own. ->tiocm[gs]et() is what actually gets called,
and mos7720 provides those, with results equivalent to what the
unreachable code would be doing when called.
Signed-off-by: Al Viro <[email protected]>
|
|
Allow matching on interfaces having two endpoints by adding a new
device-id flag.
This allows for the handling of devices whose interface numbers can
change (e.g. Quectel EP06) to be contained in the device-id table.
Tested-by: Kristian Evensen <[email protected]>
Cc: stable <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
The Quectel EP06 (and EM06/EG06) LTE modem supports updating the USB
configuration, without the VID/PID or configuration number changing.
When the configuration is updated and interfaces are added/removed, the
interface numbers are updated. This causes our current code for matching
EP06 not to work as intended, as the assumption about reserved
interfaces no longer holds. If for example the diagnostic (first)
interface is removed, option will (try to) bind to the QMI interface.
This patch improves EP06 detection by replacing the current match with
two matches, and those matches check class, subclass and protocol as
well as VID and PID. The diag interface exports class, subclass and
protocol as 0xff. For the other serial interfaces, class is 0xff and
subclass and protocol are both 0x0.
The modem can export the following devices and always in this order:
diag, nmea, at, ppp. qmi and adb. This means that diag can only ever be
interface 0, and interface numbers 1-5 should be marked as reserved. The
three other serial devices can have interface numbers 0-3, but I have
not marked any interfaces as reserved. The reason is that the serial
devices are the only interfaces exported by the device where subclass
and protocol is 0x0.
QMI exports the same class, subclass and protocol values as the diag
interface. However, the two interfaces have different number of
endpoints, QMI has three and diag two. I have added a check for number
of interfaces if VID/PID matches the EP06, and we ignore the device if
number of interfaces equals three (and subclass is set).
Signed-off-by: Kristian Evensen <[email protected]>
Acked-by: Dan Williams <[email protected]>
[ johan: drop uneeded RSVD(5) for ADB ]
Cc: stable <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
Similarly to a recently reported bug in io_ti, a malicious USB device
could set port_number to a negative value and we would underflow the
port array in the interrupt completion handler.
As these devices only have one or two ports, fix this by making sure we
only consider the seventh bit when determining the port number (and
ignore bits 0xb0 which are typically set to 0x30).
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
As reported by Dan Carpenter, a malicious USB device could set
port_number to a negative value and we would underflow the port array in
the interrupt completion handler.
As these devices only have one or two ports, fix this by making sure we
only consider the seventh bit when determining the port number (and
ignore bits 0xb0 which are typically set to 0x30).
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable <[email protected]>
Reported-by: Dan Carpenter <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
Signed-off-by: Movie Song <[email protected]>
Cc: Johan Hovold <[email protected]>
Cc: stable <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The device exposes AT, NMEA and DIAG ports in both USB configurations.
The patch explicitly ignores interfaces 0 and 1, as they're bound to
other drivers already; and also interface 6, which is a GNSS interface
for which we don't have a driver yet.
T: Bus=01 Lev=03 Prnt=04 Port=00 Cnt=01 Dev#= 18 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 2
P: Vendor=413c ProdID=81d7 Rev=03.18
S: Manufacturer=DELL
S: Product=DW5821e Snapdragon X20 LTE
S: SerialNumber=0123456789ABCDEF
C: #Ifs= 7 Cfg#= 2 Atr=a0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 6 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
T: Bus=01 Lev=03 Prnt=04 Port=00 Cnt=01 Dev#= 16 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 2
P: Vendor=413c ProdID=81d7 Rev=03.18
S: Manufacturer=DELL
S: Product=DW5821e Snapdragon X20 LTE
S: SerialNumber=0123456789ABCDEF
C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I: If#= 1 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=00 Prot=00 Driver=usbhid
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
Signed-off-by: Aleksander Morgado <[email protected]>
Cc: stable <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for v4.19-rc1
Here are the USB-serial updates for 4.19-rc1, including:
- gpio support for CP2102N devices
- improved line-speed handling for cp210x
- conversion to spin_lock_irqsave() in completion handlers
- dropped kl5kusb105 support from the kl5kusb105 driver (sic!)
Included are also various lower-priority fixes and clean ups.
All but the final commit have been in linux-next, and with no reported
issues.
Signed-off-by: Johan Hovold <[email protected]>
|
|
This patch adds GPIO support for CP2102N devices.
It introduces new generic code to support emulating separate
input and outputs directions even though these devices
only know output modes (open-drain and pushpull). Existing
GPIO support for CP2105 has been migrated over to the new
code structure.
Only limitation is that for the QFN28 variant, only 4 out of
7 GPIOs are supported. This is because the config array
locations of the last 3 pins are not documented, and reverse
engineering revealed offsets that conflicted with other
documented functions. Hence we'll play it safe instead
until somebody clears this up further.
Signed-off-by: Karoly Pados <[email protected]>
[ johan: fix style issues and a couple of minor bugs; use Karoly's
updated commit message ]
Acked-by: Martyn Welch <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
CP2104 and the ECI interface of CP2105 support further baud rates than
the ones specified in AN205 table 1, and we can use the same equations
as for CP2102N to determine and report back the actual baud rates used.
Note that this could eventually be generalised also to CP2108, which
uses a different base clock. There appears to be an error in the CP2108
equations which needs to be confirmed on actual hardware first however
(specifically, the subtraction of one from the divisor appears to be
incorrect as it introduces larger errors).
Reviewed-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
The CP2102N equations for determining the actual baud rate can be used
also for other device types, so let's factor it out.
Note that this removes the now unused cp210x_is_cp2102n() helper.
Reviewed-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
CP2102N devices support a lot more baudrates than earlier chips by
SiLabs. These devices are not constrained anymore by the table in AN205,
and are able to generate almost any baudrate in the supported range
with only minimal errors. This has also been verified with a scope on
a physical device. This patch adds support for all baudrates supported
by the CP2102N.
Signed-off-by: Karoly Pados <[email protected]>
[johan: rework on top of an205 and max-speed patches ]
Reviewed-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
Newer cp210x devices support higher line speeds than the older ones
which supported a discrete set of speeds up to 921.6 kbaud.
To support these higher speeds, we have for some time mapped speeds
lower than 1 Mbaud to the speeds supported by older devices, while
allowing the device to pick the closest possible rate for higher speeds
(without trying to guess and report back what rate was actually chosen).
As this implementation can lead to undefined behaviour for older devices
which do not support the higher rates, let's use the later-added
device-type detection to determine the maximum supported speed.
This will also be useful when adding support for cp2102n which can
handle rates up to 3 Mbaud.
As per the data sheets the following maximum speeds are used
cp2101 921.6 kbaud
cp2102/3 1 Mbaud
cp2104/8 2 Mbaud
cp2105
- ECI port 2 Mbaud
- SCI port 921.6 kbaud
while keeping the maximum 2 Mbaud for unknown device types in order to
avoid any regressions.
Reviewed-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
Older cp210x devices only support a fixed set of line speeds to which a
requested speed is mapped. Reimplement this mapping using a table
instead of a long if-else construct.
Reviewed-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
Drop redundant input-speed re-encoding at every open(). The output and
input speeds are initialised to the same value and are kept in sync on
termios updates.
Reviewed-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
Drop unused driver-data baud rate.
Reviewed-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
Variables iflag, mask and serial are being assigned but are never used
hence are redundant and can be removed.
Cleans up clang warnings:
warning: variable 'iflag' set but not used [-Wunused-but-set-variable]
warning: variable 'mask' set but not used [-Wunused-but-set-variable]
warning: variable 'serial' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
This driver was apparently never tested with an actual KLSI device. In
fact, even the device-id entry which was supposed to allow for this had
a typo in it.
Tests now reveal that the predicted firmware differences with the
PalmConnect adapters are real and that the driver does not support KLSI
devices with PID 0x000c, so let's remove the broken entry.
Reported-by: Chris Jakob <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
Add missing version-request error handling and suppress printing of the
(zeroed) transfer-buffer content in case of errors.
Signed-off-by: Johan Hovold <[email protected]>
|
|
Make sure to return -EIO in case of a short modem-status read request.
While at it, split the debug message to not include the (zeroed)
transfer-buffer content in case of errors.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Johan Hovold <[email protected]>
|
|
Add missing transfer-length sanity check to the status-register
completion handler to avoid leaking bits of uninitialised slab data to
user space.
Fixes: 3f5429746d91 ("USB: Moschip 7840 USB-Serial Driver")
Cc: stable <[email protected]> # 2.6.19
Signed-off-by: Johan Hovold <[email protected]>
|
|
Fix broken modem-status error handling which could lead to bits of slab
data leaking to user space.
Fixes: 3b36a8fd6777 ("usb: fix uninitialized variable warning in keyspan_pda")
Cc: stable <[email protected]> # 2.6.27
Signed-off-by: Johan Hovold <[email protected]>
|
|
There are two versions of the Qivicon Zigbee stick in circulation. This
adds the second USB ID to the cp210x driver.
Signed-off-by: Olli Salonen <[email protected]>
Cc: stable <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
The "r" variable is an int and "bufsize" is an unsigned int so the
comparison is type promoted to unsigned. If usb_control_msg() returns a
negative that is treated as a high positive value and the error handling
doesn't work.
Fixes: 2d5a9c72d0c4 ("USB: serial: ch341: fix control-message error handling")
Signed-off-by: Dan Carpenter <[email protected]>
Cc: stable <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
Add a "tty_" prefix to the tty "flag" variable to avoid any future
mixups with the recently added irq-mask "flags" one.
Reviewed-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: John Ogness <[email protected]>
Signed-off-by: Sebastian Andrzej Siewior <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: John Ogness <[email protected]>
Signed-off-by: Sebastian Andrzej Siewior <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: John Ogness <[email protected]>
Signed-off-by: Sebastian Andrzej Siewior <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: John Ogness <[email protected]>
Signed-off-by: Sebastian Andrzej Siewior <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
The portdata spinlock can be taken in interrupt context (via
sierra_outdat_callback()).
Disable interrupts when taking the portdata spinlock when discarding
deferred URBs during close to prevent a possible deadlock.
Fixes: 014333f77c0b ("USB: sierra: fix urb and memory leak on disconnect")
Cc: stable <[email protected]>
Signed-off-by: John Ogness <[email protected]>
Signed-off-by: Sebastian Andrzej Siewior <[email protected]>
[ johan: amend commit message and add fixes and stable tags ]
Signed-off-by: Johan Hovold <[email protected]>
|
|
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: John Ogness <[email protected]>
Signed-off-by: Sebastian Andrzej Siewior <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: John Ogness <[email protected]>
Signed-off-by: Sebastian Andrzej Siewior <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: John Ogness <[email protected]>
Signed-off-by: Sebastian Andrzej Siewior <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: John Ogness <[email protected]>
Signed-off-by: Sebastian Andrzej Siewior <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: John Ogness <[email protected]>
Signed-off-by: Sebastian Andrzej Siewior <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: John Ogness <[email protected]>
Signed-off-by: Sebastian Andrzej Siewior <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: John Ogness <[email protected]>
Signed-off-by: Sebastian Andrzej Siewior <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
Negative error code will be larger than sizeof().
Note that none of these bugs prevent errors from being detected, even if
the ir-usb one would cause a less precise debug message to printed.
Signed-off-by: Chengguang Xu <[email protected]>
[ johan: add comment about implications ]
Signed-off-by: Johan Hovold <[email protected]>
|
|
Add device ids for CESINEL products.
Reported-by: Carlos Barcala Lara <[email protected]>
Cc: stable <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
Silicon Labs defines alternative VID/PID pairs for some chips that when
used will automatically install drivers for Windows users without manual
intervention. Unfortunately, these IDs are not recognized by the Linux
module, so using these IDs improves user experience on one platform but
degrades it on Linux. This patch addresses this problem.
Signed-off-by: Karoly Pados <[email protected]>
Cc: stable <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
The kmalloc() function has a 2-factor argument form, kmalloc_array(). This
patch replaces cases of:
kmalloc(a * b, gfp)
with:
kmalloc_array(a * b, gfp)
as well as handling cases of:
kmalloc(a * b * c, gfp)
with:
kmalloc(array3_size(a, b, c), gfp)
as it's slightly less ugly than:
kmalloc_array(array_size(a, b), c, gfp)
This does, however, attempt to ignore constant size factors like:
kmalloc(4 * 1024, gfp)
though any constants defined via macros get caught up in the conversion.
Any factors with a sizeof() of "unsigned char", "char", and "u8" were
dropped, since they're redundant.
The tools/ directory was manually excluded, since it has its own
implementation of kmalloc().
The Coccinelle script used for this was:
// Fix redundant parens around sizeof().
@@
type TYPE;
expression THING, E;
@@
(
kmalloc(
- (sizeof(TYPE)) * E
+ sizeof(TYPE) * E
, ...)
|
kmalloc(
- (sizeof(THING)) * E
+ sizeof(THING) * E
, ...)
)
// Drop single-byte sizes and redundant parens.
@@
expression COUNT;
typedef u8;
typedef __u8;
@@
(
kmalloc(
- sizeof(u8) * (COUNT)
+ COUNT
, ...)
|
kmalloc(
- sizeof(__u8) * (COUNT)
+ COUNT
, ...)
|
kmalloc(
- sizeof(char) * (COUNT)
+ COUNT
, ...)
|
kmalloc(
- sizeof(unsigned char) * (COUNT)
+ COUNT
, ...)
|
kmalloc(
- sizeof(u8) * COUNT
+ COUNT
, ...)
|
kmalloc(
- sizeof(__u8) * COUNT
+ COUNT
, ...)
|
kmalloc(
- sizeof(char) * COUNT
+ COUNT
, ...)
|
kmalloc(
- sizeof(unsigned char) * COUNT
+ COUNT
, ...)
)
// 2-factor product with sizeof(type/expression) and identifier or constant.
@@
type TYPE;
expression THING;
identifier COUNT_ID;
constant COUNT_CONST;
@@
(
- kmalloc
+ kmalloc_array
(
- sizeof(TYPE) * (COUNT_ID)
+ COUNT_ID, sizeof(TYPE)
, ...)
|
- kmalloc
+ kmalloc_array
(
- sizeof(TYPE) * COUNT_ID
+ COUNT_ID, sizeof(TYPE)
, ...)
|
- kmalloc
+ kmalloc_array
(
- sizeof(TYPE) * (COUNT_CONST)
+ COUNT_CONST, sizeof(TYPE)
, ...)
|
- kmalloc
+ kmalloc_array
(
- sizeof(TYPE) * COUNT_CONST
+ COUNT_CONST, sizeof(TYPE)
, ...)
|
- kmalloc
+ kmalloc_array
(
- sizeof(THING) * (COUNT_ID)
+ COUNT_ID, sizeof(THING)
, ...)
|
- kmalloc
+ kmalloc_array
(
- sizeof(THING) * COUNT_ID
+ COUNT_ID, sizeof(THING)
, ...)
|
- kmalloc
+ kmalloc_array
(
- sizeof(THING) * (COUNT_CONST)
+ COUNT_CONST, sizeof(THING)
, ...)
|
- kmalloc
+ kmalloc_array
(
- sizeof(THING) * COUNT_CONST
+ COUNT_CONST, sizeof(THING)
, ...)
)
// 2-factor product, only identifiers.
@@
identifier SIZE, COUNT;
@@
- kmalloc
+ kmalloc_array
(
- SIZE * COUNT
+ COUNT, SIZE
, ...)
// 3-factor product with 1 sizeof(type) or sizeof(expression), with
// redundant parens removed.
@@
expression THING;
identifier STRIDE, COUNT;
type TYPE;
@@
(
kmalloc(
- sizeof(TYPE) * (COUNT) * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
kmalloc(
- sizeof(TYPE) * (COUNT) * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
kmalloc(
- sizeof(TYPE) * COUNT * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
kmalloc(
- sizeof(TYPE) * COUNT * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
kmalloc(
- sizeof(THING) * (COUNT) * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
|
kmalloc(
- sizeof(THING) * (COUNT) * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
|
kmalloc(
- sizeof(THING) * COUNT * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
|
kmalloc(
- sizeof(THING) * COUNT * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
)
// 3-factor product with 2 sizeof(variable), with redundant parens removed.
@@
expression THING1, THING2;
identifier COUNT;
type TYPE1, TYPE2;
@@
(
kmalloc(
- sizeof(TYPE1) * sizeof(TYPE2) * COUNT
+ array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
, ...)
|
kmalloc(
- sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+ array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
, ...)
|
kmalloc(
- sizeof(THING1) * sizeof(THING2) * COUNT
+ array3_size(COUNT, sizeof(THING1), sizeof(THING2))
, ...)
|
kmalloc(
- sizeof(THING1) * sizeof(THING2) * (COUNT)
+ array3_size(COUNT, sizeof(THING1), sizeof(THING2))
, ...)
|
kmalloc(
- sizeof(TYPE1) * sizeof(THING2) * COUNT
+ array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
, ...)
|
kmalloc(
- sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+ array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
, ...)
)
// 3-factor product, only identifiers, with redundant parens removed.
@@
identifier STRIDE, SIZE, COUNT;
@@
(
kmalloc(
- (COUNT) * STRIDE * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
kmalloc(
- COUNT * (STRIDE) * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
kmalloc(
- COUNT * STRIDE * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
kmalloc(
- (COUNT) * (STRIDE) * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
kmalloc(
- COUNT * (STRIDE) * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
kmalloc(
- (COUNT) * STRIDE * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
kmalloc(
- (COUNT) * (STRIDE) * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
kmalloc(
- COUNT * STRIDE * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
)
// Any remaining multi-factor products, first at least 3-factor products,
// when they're not all constants...
@@
expression E1, E2, E3;
constant C1, C2, C3;
@@
(
kmalloc(C1 * C2 * C3, ...)
|
kmalloc(
- (E1) * E2 * E3
+ array3_size(E1, E2, E3)
, ...)
|
kmalloc(
- (E1) * (E2) * E3
+ array3_size(E1, E2, E3)
, ...)
|
kmalloc(
- (E1) * (E2) * (E3)
+ array3_size(E1, E2, E3)
, ...)
|
kmalloc(
- E1 * E2 * E3
+ array3_size(E1, E2, E3)
, ...)
)
// And then all remaining 2 factors products when they're not all constants,
// keeping sizeof() as the second factor argument.
@@
expression THING, E1, E2;
type TYPE;
constant C1, C2, C3;
@@
(
kmalloc(sizeof(THING) * C2, ...)
|
kmalloc(sizeof(TYPE) * C2, ...)
|
kmalloc(C1 * C2 * C3, ...)
|
kmalloc(C1 * C2, ...)
|
- kmalloc
+ kmalloc_array
(
- sizeof(TYPE) * (E2)
+ E2, sizeof(TYPE)
, ...)
|
- kmalloc
+ kmalloc_array
(
- sizeof(TYPE) * E2
+ E2, sizeof(TYPE)
, ...)
|
- kmalloc
+ kmalloc_array
(
- sizeof(THING) * (E2)
+ E2, sizeof(THING)
, ...)
|
- kmalloc
+ kmalloc_array
(
- sizeof(THING) * E2
+ E2, sizeof(THING)
, ...)
|
- kmalloc
+ kmalloc_array
(
- (E1) * E2
+ E1, E2
, ...)
|
- kmalloc
+ kmalloc_array
(
- (E1) * (E2)
+ E1, E2
, ...)
|
- kmalloc
+ kmalloc_array
(
- E1 * E2
+ E1, E2
, ...)
)
Signed-off-by: Kees Cook <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB and PHY updates from Greg KH:
"Here is the big USB pull request for 4.18-rc1.
Lots of stuff here, the highlights are:
- phy driver updates and new additions
- usual set of xhci driver updates
- normal set of musb updates
- gadget driver updates and new controllers
- typec work, it's getting closer to getting fully out of the staging
portion of the tree.
- lots of minor cleanups and bugfixes.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (263 commits)
Revert "xhci: Reset Renesas uPD72020x USB controller for 32-bit DMA issue"
xhci: Add quirk to zero 64bit registers on Renesas PCIe controllers
xhci: Allow more than 32 quirks
usb: xhci: force all memory allocations to node
selftests: add test for USB over IP driver
USB: typec: fsusb302: no need to check return value of debugfs_create_dir()
USB: gadget: udc: s3c2410_udc: no need to check return value of debugfs_create functions
USB: gadget: udc: renesas_usb3: no need to check return value of debugfs_create functions
USB: gadget: udc: pxa27x_udc: no need to check return value of debugfs_create functions
USB: gadget: udc: gr_udc: no need to check return value of debugfs_create functions
USB: gadget: udc: bcm63xx_udc: no need to check return value of debugfs_create functions
USB: udc: atmel_usba_udc: no need to check return value of debugfs_create functions
USB: dwc3: no need to check return value of debugfs_create functions
USB: dwc2: no need to check return value of debugfs_create functions
USB: core: no need to check return value of debugfs_create functions
USB: chipidea: no need to check return value of debugfs_create functions
USB: ehci-hcd: no need to check return value of debugfs_create functions
USB: fhci-hcd: no need to check return value of debugfs_create functions
USB: fotg210-hcd: no need to check return value of debugfs_create functions
USB: imx21-hcd: no need to check return value of debugfs_create functions
...
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for v4.18-rc1
Here are the USB-serial updates for 4.18-rc1, including:
- support for hardware-assisted XON/XOFF output flow control for pl2303
- fix for a long-standing IXON/IXOFF mixup in ftdi_sio
- blacklist of two apparently unused dwm-158 modem interfaces that
confused some user space daemon (option)
- add missing const to a tty helper currently used by USB serial only
Included are also various clean ups.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <[email protected]>
|
|
Support hardware-level Xon/Xoff flow control in transmit direction with
pl2303.
I only know how to get the hardware to do IXON/!IXANY with ^S/^Q as control
characters, so I preserve the old behaviour for all other cases.
Signed-off-by: Florian Zumbiehl <[email protected]>
[ johan: rewrite logic using pl2303_termios_change() helper ]
Signed-off-by: Johan Hovold <[email protected]>
|
|
Clean up the somewhat convoluted hardware-assisted flow control
handling.
Reviewed-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
Drop urb_ prefixes from value and index variables used in control
requests.
Reviewed-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
Replace all __u types with their u counterparts throughout the driver
(whose structures are not exported to user space).
Reviewed-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
Since forever this driver has had IXON and IXOFF mixed up, and has used
the latter rather than the former to enable hardware-assisted software
flow control on output.
Reviewed-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
We already have the tty port when probing a usb-serial port so use
tty_port_register_device() directly instead of tty_port_install() later
to set up the port link.
This is a step towards enabling serdev for usb-serial (but we need to
determine how to handle hotplugging first).
Reviewed-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
Just set up the show callback in the tty_operations, and use
proc_create_single_data to create the file without additional
boilerplace code.
Signed-off-by: Christoph Hellwig <[email protected]>
|