| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The host needs to tell the device the exit latencies using the SET_SEL
request before device initiated link powermanagement can be enabled.
The exit latency values do not change after enumeration, it's enough
to set them once. So do like Windows 10 and issue the SET_SEL request
once just before setting the configuration.
This is also the sequence described in USB 3.2 specs "9.1.2 Bus
enumeration". SET_SEL is issued once before the Set Configuration
request, and won't be cleared by the Set Configuration,
Set Interface or ClearFeature (STALL) requests.
Only warm reset, hot reset, set Address 0 clears the exit latencies.
See USB 3.2 section 9.4.14 Table 9-10 Device parameters and events
Add udev->lpm_devinit_allow, and set it if SET_SEL was successful.
If not set, then don't try to enable device initiated LPM
We used to issue a SET_SEL request every time lpm is enabled for either
U1 or U2 link states, meaning a SET_SEL was issued twice after every
Set Configuration and Set Interface requests, easily accumulating to
over 15 SET_SEL requets during a USB3 webcam enumeration.
Signed-off-by: Mathias Nyman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
In some cases the port of an hub needs to be disabled or switched off
and on again. E.g. when the connected device needs to be re-enumerated.
Or it needs to be explicitly disabled while the rest of the usb tree
stays working.
For this purpose this patch adds an sysfs switch to enable/disable the
port on any hub. In the case the hub is supporting power switching, the
power line will be disabled to the connected device.
When the port gets disabled, the associated device gets disconnected and
removed from the logical usb tree. No further device will be enumerated
on that port until the port gets enabled again.
Reviewed-by: Alan Stern <[email protected]>
Signed-off-by: Michael Grzeschik <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Add USB_QUIRK_NO_LPM and USB_QUIRK_RESET_RESUME quirks for Dell usb gen
2 device to not fail during enumeration.
Found this bug on own testing
Signed-off-by: Monish Kumar R <[email protected]>
Cc: stable <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
kasprintf() returns NULL or valid pointer. Since kfree() can handle
NULL pointer condition, simplify error and success paths in function
port_over_current_notify() by removing multiple error path labels.
Signed-off-by: Bhuvanesh Surachari <[email protected]>
Signed-off-by: Eugeniu Rosca <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
It has been observed with certain PCIe USB cards (like Inateck connected
to AM64 EVM or J7200 EVM) that as soon as the primary roothub is
registered, port status change is handled even before xHC is running
leading to cold plug USB devices not detected. For such cases, registering
both the root hubs along with the second HCD is required. Add support for
deferring roothub registration in usb_add_hcd(), so that both primary and
secondary roothubs are registered along with the second HCD.
This patch has been added and reverted earier as it triggered a race
in usb device enumeration.
That race is now fixed in 5.16-rc3, and in stable back to 5.4
commit 6cca13de26ee ("usb: hub: Fix locking issues with address0_mutex")
commit 6ae6dc22d2d1 ("usb: hub: Fix usb enumeration issue due to address0
race")
CC: [email protected] # 5.4+
Suggested-by: Mathias Nyman <[email protected]>
Tested-by: Chris Chiu <[email protected]>
Acked-by: Alan Stern <[email protected]>
Signed-off-by: Kishon Vijay Abraham I <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The controller device (hcd) does not always have the ACPI
companion assigned to it at all. We can not rely on it when
finding the ACPI companion for the root hub. Instead we need
to use the sysdev pointer.
Signed-off-by: Heikki Krogerus <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
This reverts commit c40b62216c1aecc0dc00faf33d71bd71cb440337.
The series still has built errors as reported in linux-next, so revert
it for now.
Reported-by: Stephen Rothwell <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Cc: Stephen Boyd <[email protected]>
Cc: Douglas Anderson <[email protected]>
Cc: Matthias Kaehlcke <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
We need the USB fixes in here, and this resolves a merge issue in
drivers/usb/dwc3/drd.c
Reported-by: Stephen Rothwell <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Call onboard_hub_create/destroy_pdevs() from usb_add/remove_hcd()
for primary HCDs to create/destroy platform devices for onboard
USB hubs that may be connected to the root hub of the controller.
These functions are a NOP unless CONFIG_USB_ONBOARD_HUB=y/m.
Also add a field to struct usb_hcd to keep track of the onboard hub
platform devices that are owned by the HCD.
Reviewed-by: Douglas Anderson <[email protected]>
Reviewed-by: Stephen Boyd <[email protected]>
Signed-off-by: Matthias Kaehlcke <[email protected]>
Link: https://lore.kernel.org/r/20220217104219.v21.3.I7a3a7d9d2126c34079b1cab87aa0b2ec3030f9b7@changeid
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The USB device dump code often checks for the buffer overflow just before
calling the functions that do that first thing anyways. Such checks are
redundant and may be dropped...
Signed-off-by: Sergey Shtylyov <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The third argument of usb_maxpacket(): in_out has been deprecated
because it could be derived from the second argument (e.g. using
usb_pipeout(pipe)).
N.B. function usb_maxpacket() was made variadic to accommodate the
transition from the old prototype with three arguments to the new one
with only two arguments (so that no renaming is needed). The variadic
argument is to be removed once all users of usb_maxpacket() get
migrated.
CC: Duncan Sands <[email protected]>
CC: Alan Stern <[email protected]>
CC: Olav Kongas <[email protected]>
CC: Rui Miguel Silva <[email protected]>
Signed-off-by: Vincent Mailhol <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The documentation for the freeze() method says that it "should quiesce
the device so that it doesn't generate IRQs or DMA". The unspoken
consequence of not doing this is that MSIs aimed at non-boot CPUs may
get fully lost if they're sent during the period where the target CPU is
offline.
The current callbacks for USB HCD do not fully quiesce interrupts,
specifically on XHCI. Change to use the full suspend/resume flow for
freeze/thaw to ensure interrupts are fully quiesced. This fixes issues
where USB devices fail to thaw during hibernation because XHCI misses
its interrupt and cannot recover.
Acked-by: Alan Stern <[email protected]>
Signed-off-by: Evan Green <[email protected]>
Link: https://lore.kernel.org/r/20220421103751.v3.2.I8226c7fdae88329ef70957b96a39b346c69a914e@changeid
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The PM_EVENT_FREEZE and PM_EVENT_QUIESCE messages should cause the
device to stop generating interrupts. USB core was previously allowing
devices that were already runtime suspended to keep remote wakeup
enabled if they had gone down that way. This violates the contract with
pm, and can potentially cause MSI interrupts to be lost.
Change that so that if a device is runtime suspended with remote wakeups
enabled, it will be resumed to ensure remote wakeup is always disabled
across a freeze.
Acked-by: Alan Stern <[email protected]>
Signed-off-by: Evan Green <[email protected]>
Link: https://lore.kernel.org/r/20220421103751.v3.1.I2c636c4decc358f5e6c27b810748904cc69beada@changeid
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
usb_dump_hub_descriptor() and usb_dump_string() are defined under #ifdef
PROC_EXTRA (while PROC_EXTRA doesn't seem to have ever been #define'd)
since the dawn of the git era -- remove this dead code at last...
Signed-off-by: Sergey Shtylyov <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Since commit ae8709b296d8 ("USB: core: Make do_proc_control() and
do_proc_bulk() killable") if a device has the USB_QUIRK_DELAY_CTRL_MSG
quirk set, it will temporarily block all other URBs (e.g. interrupts)
while sleeping due to a control.
This results in noticeable delays when, for example, a userspace usbfs
application is sending URB interrupts at a high rate to a keyboard and
simultaneously updates the lock indicators using controls. Interrupts
with direction set to IN are also affected by this, meaning that
delivery of HID reports (containing scancodes) to the usbfs application
is delayed as well.
This patch fixes the regression by calling msleep() while the device
mutex is unlocked, as was the case originally with usb_control_msg().
Fixes: ae8709b296d8 ("USB: core: Make do_proc_control() and do_proc_bulk() killable")
Cc: stable <[email protected]>
Acked-by: Alan Stern <[email protected]>
Signed-off-by: Tasos Sahanidis <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
powerpc's asm/prom.h brings some headers that it doesn't
need itself.
In order to clean it up in a further step, first clean all
files that include asm/prom.h
Some files don't need asm/prom.h at all. For those ones,
just remove inclusion of asm/prom.h
Some files don't need any of the items provided by asm/prom.h,
but need some of the headers included by asm/prom.h. For those
ones, add the needed headers that are brought by asm/prom.h at
the moment, then remove asm/prom.h
Some files really need asm/prom.h but also need some of the
headers included by asm/prom.h. For those one, leave asm/prom.h
but also add the needed headers so that they can be removed
from asm/prom.h in a later step.
Signed-off-by: Christophe Leroy <[email protected]>
Link: https://lore.kernel.org/r/295e87a3094a92784657f7060fb0927e762a2e3c.1650011506.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
This has been reported to stall if queried
Cc: stable <[email protected]>
Signed-off-by: Oliver Neukum <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
This device is reported to stall when enummerated.
Cc: stable <[email protected]>
Signed-off-by: Oliver Neukum <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt changes for 5.18-rc1.
Nothing major in here, just lots of little improvements and cleanups
and new device support. Highlights are:
- list iterator fixups for when we walk past the end of the list (a
common problem that was cut/pasted in almost all USB gadget
drivers)
- xen USB driver "hardening" for malicious hosts
- xhci driver updates and fixes for more hardware types
- xhci debug cable fixes to make it actually work again
- usb gadget audio driver improvements
- usb gadget storage fixes to work with OS-X
- lots of other small usb gadget fixes and updates
- USB DWC3 driver improvements for more hardware types
- Lots of other small USB driver improvements
- DTS updates for some USB platforms
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (172 commits)
usb: gadget: fsl_qe_udc: Add missing semicolon in qe_ep_dequeue()
dt-bindings: usb: mtk-xhci: add compatible for mt8186
usb: dwc3: Issue core soft reset before enabling run/stop
usb: gadget: Makefile: remove ccflags-y
USB: usb-storage: Fix use of bitfields for hardware data in ene_ub6250.c
usb: gadget: eliminate anonymous module_init & module_exit
usb: usbip: eliminate anonymous module_init & module_exit
xen/usb: harden xen_hcd against malicious backends
usb: dwc3: gadget: Wait for ep0 xfers to complete during dequeue
usb: dwc3: gadget: move cmd_endtransfer to extra function
usb: dwc3: gadget: ep_queue simplify isoc start condition
xen/usb: don't use arbitrary_virt_to_machine()
usb: isp1760: remove redundant max_packet() macro
usb: oxu210hp-hcd: remove redundant call to max_packet() macro
usb: common: usb-conn-gpio: Make VBUS supply completely optional
USB: storage: ums-realtek: fix error code in rts51x_read_mem()
usb: early: xhci-dbc: Fix xdbc number parsing
usb: early: xhci-dbc: Remove duplicate keep parsing
x86/tsc: Be consistent about use_tsc_delay()
usb: gadget: udc: s3c2410: remove usage of list iterator past the loop body
...
|
|
Currently, suspend_report_result() prints only function information.
If any driver uses a common PM function, nobody knows who exactly
called the failing function.
A device pinter is needed to recognize the failing device.
For example:
PM: dpm_run_callback(): pnp_bus_suspend+0x0/0x10 returns 0
PM: dpm_run_callback(): pci_pm_suspend+0x0/0x150 returns 0
become after the change:
serial 00:05: PM: dpm_run_callback(): pnp_bus_suspend+0x0/0x10 returns 0
pci 0000:00:01.3: PM: dpm_run_callback(): pci_pm_suspend+0x0/0x150 returns 0
Signed-off-by: Youngjin Jang <[email protected]>
[ rjw: Changelog edits ]
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
The kerneldoc for usb_get_dev() and usb_get_intf() says that drivers
should always refcount the references they hold for the usb_device or
usb_interface structure, respectively. But this is an overstatement:
In many cases drivers do not access these references after they have
been unbound, and in such cases refcounting is unnecessary.
This patch updates the kerneldoc for the two routines, explaining when
a driver does not need to increment and decrement the refcount. This
should help dispel misconceptions which might otherwise afflict
programmers new to the USB subsystem.
Signed-off-by: Alan Stern <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Trying to disable Link Powermanagement (LPM) before port reset is
unnecessary and can cause additional delay if host can't communicate
with the device, which is often the reason why device is reset in the
first place.
usb_disable_lpm() will
- zero usb U1/U2 timeouts for the hub downstream port
- send ENABLE U1/U2 clear feature requests to the connected device.
- increase internal reference count for udev->lpm_disable_count
There is no need to zero U1/U2 hub port timeouts, or clearing the
U1/U2 enable for the connected device before reset. These are set
to default by the reset.
USB 3.1 section 10.2.2 "HUB Downstream port U1/U2 timers" states that:
"the U1 and U2 timeout values for a downstream port reset to the default
values when the port receives a SetPortFeature request for a port reset"
Set the udev->lpm_disable_count to "1" after port reset, which is the
default lpm_disable_count value when allocating udev, representing
disabled LPM.
Cc: Alan Stern <[email protected]>
Signed-off-by: Mathias Nyman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
We need the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
While the existing code code imposes a limit on the used memory, it might be
over pessimistic (even if this is unlikely).
Example scenario:
8 threads running in parallel, all entering
"usbfs_increase_memory_usage()" at the same time.
The atomic accesses in "usbfs_increase_memory_usage()" could be
serialized like this:
8 x "atomic64_add"
8 x "atomic64_read"
If the 8 x "atomic64_add" raise "usbfs_memory_usage" above the limit,
then all 8 calls of "usbfs_increase_memory_usage()" will return with
-ENOMEM. If you instead serialize over the whole access to
"usbfs_memory_usage" by using a spinlock, some of these calls will
succeed.
Acked-by: Alan Stern <[email protected]>
Signed-off-by: Ingo Rohloff <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Commit 8c67d06f3fd9 ("usb: Link the ports to the connectors they are
attached to") creates a link to the USB Type-C connector for every new
port that is added when possible. If component_add() fails,
usb_hub_create_port_device() prints a warning but does not unregister
the device and does not return errors to the callers.
Syzbot reported a "WARNING in component_del()".
Fix this issue in usb_hub_create_port_device by calling device_unregister()
and returning the errors from component_add().
Fixes: 8c67d06f3fd9 ("usb: Link the ports to the connectors they are attached to")
Reported-and-tested-by: [email protected]
Reviewed-by: Heikki Krogerus <[email protected]>
Signed-off-by: Fabio M. De Francesco <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Replace acpi_bus_get_device() that is going to be dropped with
acpi_fetch_acpi_dev().
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <[email protected]>
Link: https://lore.kernel.org/r/1899393.PYKUYFuaPT@kreacher
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
We need the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
usb_hcd_pci_probe() searches for an I/O BAR using a combination of
PCI_STD_NUM_BARS (to control loop iteration) and PCI_ROM_RESOURCE (to check
whether the loop exits without finding anything).
Use PCI_STD_NUM_BARS consistently.
No functional change since PCI_STD_NUM_BARS == PCI_ROM_RESOURCE, but this
removes a dependency on that relationship and makes the code read better.
Fixes: c9c13ba428ef ("PCI: Add PCI_STD_NUM_BARS for the number of standard BARs")
Cc: Denis Efremov <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Unplugging USB device may cause an incorrect warm reset loop and the
port can no longer be used:
[ 143.039019] xhci_hcd 0000:00:14.0: Port change event, 2-3, id 19, portsc: 0x4202c0
[ 143.039025] xhci_hcd 0000:00:14.0: handle_port_status: starting usb2 port polling.
[ 143.039051] hub 2-0:1.0: state 7 ports 10 chg 0000 evt 0008
[ 143.039058] xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x4202c0, return 0x4102c0
[ 143.039092] xhci_hcd 0000:00:14.0: clear port3 connect change, portsc: 0x4002c0
[ 143.039096] usb usb2-port3: link state change
[ 143.039099] xhci_hcd 0000:00:14.0: clear port3 link state change, portsc: 0x2c0
[ 143.039101] usb usb2-port3: do warm reset
[ 143.096736] xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x2b0, return 0x2b0
[ 143.096751] usb usb2-port3: not warm reset yet, waiting 50ms
[ 143.131500] xhci_hcd 0000:00:14.0: Can't queue urb, port error, link inactive
[ 143.138260] xhci_hcd 0000:00:14.0: Port change event, 2-3, id 19, portsc: 0x2802a0
[ 143.138263] xhci_hcd 0000:00:14.0: handle_port_status: starting usb2 port polling.
[ 143.160756] xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x2802a0, return 0x3002a0
[ 143.160798] usb usb2-port3: not warm reset yet, waiting 200ms
The port status is PP=1, CCS=0, PED=0, PLS=Inactive, which is Error
state per "USB3 Root Hub Port State Machine". It's reasonable to perform
warm reset several times, but if the port is still not enabled after
many attempts, consider it's gone and treat it as disconnected.
Signed-off-by: Kai-Heng Feng <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The syzbot fuzzer has identified a bug in which processes hang waiting
for usb_kill_urb() to return. It turns out the issue is not unlinking
the URB; that works just fine. Rather, the problem arises when the
wakeup notification that the URB has completed is not received.
The reason is memory-access ordering on SMP systems. In outline form,
usb_kill_urb() and __usb_hcd_giveback_urb() operating concurrently on
different CPUs perform the following actions:
CPU 0 CPU 1
---------------------------- ---------------------------------
usb_kill_urb(): __usb_hcd_giveback_urb():
... ...
atomic_inc(&urb->reject); atomic_dec(&urb->use_count);
... ...
wait_event(usb_kill_urb_queue,
atomic_read(&urb->use_count) == 0);
if (atomic_read(&urb->reject))
wake_up(&usb_kill_urb_queue);
Confining your attention to urb->reject and urb->use_count, you can
see that the overall pattern of accesses on CPU 0 is:
write urb->reject, then read urb->use_count;
whereas the overall pattern of accesses on CPU 1 is:
write urb->use_count, then read urb->reject.
This pattern is referred to in memory-model circles as SB (for "Store
Buffering"), and it is well known that without suitable enforcement of
the desired order of accesses -- in the form of memory barriers -- it
is entirely possible for one or both CPUs to execute their reads ahead
of their writes. The end result will be that sometimes CPU 0 sees the
old un-decremented value of urb->use_count while CPU 1 sees the old
un-incremented value of urb->reject. Consequently CPU 0 ends up on
the wait queue and never gets woken up, leading to the observed hang
in usb_kill_urb().
The same pattern of accesses occurs in usb_poison_urb() and the
failure pathway of usb_hcd_submit_urb().
The problem is fixed by adding suitable memory barriers. To provide
proper memory-access ordering in the SB pattern, a full barrier is
required on both CPUs. The atomic_inc() and atomic_dec() accesses
themselves don't provide any memory ordering, but since they are
present, we can use the optimized smp_mb__after_atomic() memory
barrier in the various routines to obtain the desired effect.
This patch adds the necessary memory barriers.
CC: <[email protected]>
Reported-and-tested-by: [email protected]
Signed-off-by: Alan Stern <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Bugzilla #213839 reports a 7-port hub that doesn't work properly when
devices are plugged into some of the ports; the kernel goes into an
unending disconnect/reinitialize loop as shown in the bug report.
This "7-port hub" comprises two four-port hubs with one plugged into
the other; the failures occur when a device is plugged into one of the
downstream hub's ports. (These hubs have other problems too. For
example, they bill themselves as USB-2.0 compliant but they only run
at full speed.)
It turns out that the failures are caused by bugs in both the kernel
and the hub. The hub's bug is that it reports a different
bmAttributes value in its configuration descriptor following a remote
wakeup (0xe0 before, 0xc0 after -- the wakeup-support bit has
changed).
The kernel's bug is inside the hub driver's resume handler. When
hub_activate() sees that one of the hub's downstream ports got a
wakeup request from a child device, it notes this fact by setting the
corresponding bit in the hub->change_bits variable. But this variable
is meant for connection changes, not wakeup events; setting it causes
the driver to believe the downstream port has been disconnected and
then connected again (in addition to having received a wakeup
request).
Because of this, the hub driver then tries to check whether the device
currently plugged into the downstream port is the same as the device
that had been attached there before. Normally this check succeeds and
wakeup handling continues with no harm done (which is why the bug
remained undetected until now). But with these dodgy hubs, the check
fails because the config descriptor has changed. This causes the hub
driver to reinitialize the child device, leading to the
disconnect/reinitialize loop described in the bug report.
The proper way to note reception of a downstream wakeup request is
to set a bit in the hub->event_bits variable instead of
hub->change_bits. That way the hub driver will realize that something
has happened to the port but will not think the port and child device
have been disconnected. This patch makes that change.
Cc: <[email protected]>
Tested-by: Jonathan McDowell <[email protected]>
Signed-off-by: Alan Stern <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
When the USB core code for getting root-hub status reports was
originally written, it was assumed that the hub driver would be its
only caller. But this isn't true now; user programs can use usbfs to
communicate with root hubs and get status reports. When they do this,
they may use a transfer_buffer that is smaller than the data returned
by the HCD, which will lead to a buffer overflow error when
usb_hcd_poll_rh_status() tries to store the status data. This was
discovered by syzbot:
BUG: KASAN: slab-out-of-bounds in memcpy include/linux/fortify-string.h:225 [inline]
BUG: KASAN: slab-out-of-bounds in usb_hcd_poll_rh_status+0x5f4/0x780 drivers/usb/core/hcd.c:776
Write of size 2 at addr ffff88801da403c0 by task syz-executor133/4062
This patch fixes the bug by reducing the amount of status data if it
won't fit in the transfer_buffer. If some data gets discarded then
the URB's completion status is set to -EOVERFLOW rather than 0, to let
the user know what happened.
Reported-and-tested-by: [email protected]
Signed-off-by: Alan Stern <[email protected]>
Cc: <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
There are no more users for the function.
Reviewed-by: Andy Shevchenko <[email protected]>
Acked-by: Rafael J. Wysocki <[email protected]>
Signed-off-by: Heikki Krogerus <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Creating link to the USB Type-C connector for every new port
that is added when possible.
Reviewed-by: Andy Shevchenko <[email protected]>
Acked-by: Rafael J. Wysocki <[email protected]>
Signed-off-by: Heikki Krogerus <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
We need the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Export usb_device_match_id so that it can be used for easily matching an
usb_device with a table of IDs.
Signed-off-by: Razvan Heghedus <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
When a new USB device gets plugged to nested hubs, the affected hub,
which connects to usb 2-1.4-port2, doesn't report there's any change,
hence the nested hubs go back to runtime suspend like nothing happened:
[ 281.032951] usb usb2: usb wakeup-resume
[ 281.032959] usb usb2: usb auto-resume
[ 281.032974] hub 2-0:1.0: hub_resume
[ 281.033011] usb usb2-port1: status 0263 change 0000
[ 281.033077] hub 2-0:1.0: state 7 ports 4 chg 0000 evt 0000
[ 281.049797] usb 2-1: usb wakeup-resume
[ 281.069800] usb 2-1: Waited 0ms for CONNECT
[ 281.069810] usb 2-1: finish resume
[ 281.070026] hub 2-1:1.0: hub_resume
[ 281.070250] usb 2-1-port4: status 0203 change 0000
[ 281.070272] usb usb2-port1: resume, status 0
[ 281.070282] hub 2-1:1.0: state 7 ports 4 chg 0010 evt 0000
[ 281.089813] usb 2-1.4: usb wakeup-resume
[ 281.109792] usb 2-1.4: Waited 0ms for CONNECT
[ 281.109801] usb 2-1.4: finish resume
[ 281.109991] hub 2-1.4:1.0: hub_resume
[ 281.110147] usb 2-1.4-port2: status 0263 change 0000
[ 281.110234] usb 2-1-port4: resume, status 0
[ 281.110239] usb 2-1-port4: status 0203, change 0000, 10.0 Gb/s
[ 281.110266] hub 2-1.4:1.0: state 7 ports 4 chg 0000 evt 0000
[ 281.110426] hub 2-1.4:1.0: hub_suspend
[ 281.110565] usb 2-1.4: usb auto-suspend, wakeup 1
[ 281.130998] hub 2-1:1.0: hub_suspend
[ 281.137788] usb 2-1: usb auto-suspend, wakeup 1
[ 281.142935] hub 2-0:1.0: state 7 ports 4 chg 0000 evt 0000
[ 281.177828] usb 2-1: usb wakeup-resume
[ 281.197839] usb 2-1: Waited 0ms for CONNECT
[ 281.197850] usb 2-1: finish resume
[ 281.197984] hub 2-1:1.0: hub_resume
[ 281.198203] usb 2-1-port4: status 0203 change 0000
[ 281.198228] usb usb2-port1: resume, status 0
[ 281.198237] hub 2-1:1.0: state 7 ports 4 chg 0010 evt 0000
[ 281.217835] usb 2-1.4: usb wakeup-resume
[ 281.237834] usb 2-1.4: Waited 0ms for CONNECT
[ 281.237845] usb 2-1.4: finish resume
[ 281.237990] hub 2-1.4:1.0: hub_resume
[ 281.238067] usb 2-1.4-port2: status 0263 change 0000
[ 281.238148] usb 2-1-port4: resume, status 0
[ 281.238152] usb 2-1-port4: status 0203, change 0000, 10.0 Gb/s
[ 281.238166] hub 2-1.4:1.0: state 7 ports 4 chg 0000 evt 0000
[ 281.238385] hub 2-1.4:1.0: hub_suspend
[ 281.238523] usb 2-1.4: usb auto-suspend, wakeup 1
[ 281.258076] hub 2-1:1.0: hub_suspend
[ 281.265744] usb 2-1: usb auto-suspend, wakeup 1
[ 281.285976] hub 2-0:1.0: hub_suspend
[ 281.285988] usb usb2: bus auto-suspend, wakeup 1
USB 3.2 spec, 9.2.5.4 "Changing Function Suspend State" says that "If
the link is in a non-U0 state, then the device must transition the link
to U0 prior to sending the remote wake message", but the hub only
transits the link to U0 after signaling remote wakeup.
So be more forgiving and use a 20ms delay to let the link transit to U0
for remote wakeup.
Suggested-by: Alan Stern <[email protected]>
Acked-by: Alan Stern <[email protected]>
Signed-off-by: Kai-Heng Feng <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The wait_for_connected() function doesn't modify "*port1" and there is
no need to pass a pointer. Just pass the int itself.
Signed-off-by: Dan Carpenter <[email protected]>
Link: https://lore.kernel.org/r/20211210142028.GB18906@kili
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
During disconnect USB-3 ports often go via SS.Inactive link error state
before the missing terminations are noticed, and link finally goes to
RxDetect state
Avoid immediately warm-resetting ports in SS.Inactive state.
Let ports settle for a while and re-read the link status a few times 20ms
apart to see if the ports transitions out of SS.Inactive.
According to USB 3.x spec 7.5.2, a port in SS.Inactive should
automatically check for missing far-end receiver termination every
12 ms (SSInactiveQuietTimeout)
The futile multiple warm reset retries of a disconnected device takes
a lot of time, also the resetting of a removed devices has caused cases
where the reset bit got stuck for a long time on xHCI roothub.
This lead to issues in detecting new devices connected to the same port
shortly after.
Tested-by: Mark Pearson <[email protected]>
Signed-off-by: Mathias Nyman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
This device doesn't work well with LPM, losing connectivity intermittently.
Disable LPM to resolve the issue.
Reviewed-by: <[email protected]>
Signed-off-by: Jimmy Wang <[email protected]>
Cc: stable <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
`vaddr` is a pointer to unsigned char. sizeof(vaddr) here intends
to get the size of a pointer. But readers may get confused. Change
sizeof(vaddr) to sizeof(unsigned long) makes more sense.
Suggested-by: Alan Stern <[email protected]>
Signed-off-by: Guo Zhengkui <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
We need the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Using standard USB_EP_MAXP_MULT_MASK instead of individual bits for
extracting multiple-transactions bits from wMaxPacketSize value.
Acked-by: Alan Stern <[email protected]>
Signed-off-by: Pavel Hofman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The checks performed by commit aed9d65ac327 ("USB: validate
wMaxPacketValue entries in endpoint descriptors") require that initial
value of the maxp variable contains both maximum packet size bits
(10..0) and multiple-transactions bits (12..11). However, the existing
code assings only the maximum packet size bits. This patch assigns all
bits of wMaxPacketSize to the variable.
Fixes: aed9d65ac327 ("USB: validate wMaxPacketValue entries in endpoint descriptors")
Cc: stable <[email protected]>
Acked-by: Alan Stern <[email protected]>
Signed-off-by: Pavel Hofman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
We need the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Both driver.c and generic.c are not under drivers/usb/, should
be drivers/usb/core/ instead.
Signed-off-by: Wei Ming Chen <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
This is another branded 8153 device that doesn't work well with LPM:
r8152 2-2.1:1.0 enp0s13f0u2u1: Stop submitting intr, status -71
Disable LPM to resolve the issue.
Signed-off-by: Ole Ernst <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Fix the circular lock dependency and unbalanced unlock of addess0_mutex
introduced when fixing an address0_mutex enumeration retry race in commit
ae6dc22d2d1 ("usb: hub: Fix usb enumeration issue due to address0 race")
Make sure locking order between port_dev->status_lock and address0_mutex
is correct, and that address0_mutex is not unlocked in hub_port_connect
"done:" codepath which may be reached without locking address0_mutex
Fixes: 6ae6dc22d2d1 ("usb: hub: Fix usb enumeration issue due to address0 race")
Cc: <[email protected]>
Reported-by: Marek Szyprowski <[email protected]>
Tested-by: Hans de Goede <[email protected]>
Tested-by: Marek Szyprowski <[email protected]>
Acked-by: Hans de Goede <[email protected]>
Signed-off-by: Mathias Nyman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
xHC hardware can only have one slot in default state with address 0
waiting for a unique address at a time, otherwise "undefined behavior
may occur" according to xhci spec 5.4.3.4
The address0_mutex exists to prevent this across both xhci roothubs.
If hub_port_init() fails, it may unlock the mutex and exit with a xhci
slot in default state. If the other xhci roothub calls hub_port_init()
at this point we end up with two slots in default state.
Make sure the address0_mutex protects the slot default state across
hub_port_init() retries, until slot is addressed or disabled.
Note, one known minor case is not fixed by this patch.
If device needs to be reset during resume, but fails all hub_port_init()
retries in usb_reset_and_verify_device(), then it's possible the slot is
still left in default state when address0_mutex is unlocked.
Cc: <[email protected]>
Fixes: 638139eb95d2 ("usb: hub: allow to process more usb hub events in parallel")
Signed-off-by: Mathias Nyman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
This reverts commit 58877b0824da15698bd85a0a9dbfa8c354e6ecb7.
It has been reported to be causing problems in Arch and Fedora bug
reports.
Reported-by: Hans de Goede <[email protected]>
Link: https://bbs.archlinux.org/viewtopic.php?pid=2000956#p2000956
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2019542
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2019576
Link: https://lore.kernel.org/r/[email protected]
Cc: Mathias Nyman <[email protected]>
Cc: Chris Chiu <[email protected]>
Cc: Alan Stern <[email protected]>
Cc: Kishon Vijay Abraham I <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|