| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This is the same issue that was fixed for the VGA text buffer in commit
39cdb68c64d8 ("vt: fix memory overlapping when deleting chars in the
buffer"). The cure is also the same i.e. replace memcpy() with memmove()
due to the overlaping buffers.
Signed-off-by: Nicolas Pitre <[email protected]>
Fixes: 81732c3b2fed ("tty vt: Fix line garbage in virtual console on command line edition")
Cc: stable <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
We accidently met the issue that the bash prompt is not shown after the
previous command done and until the next input if there's only one CPU
(In our issue other CPUs are isolated by isolcpus=). Further analysis
shows it's because the port entering runtime suspend even if there's
still pending chars in the buffer and the pending chars will only be
processed in next device resuming. We are using amba-pl011 and the
problematic flow is like below:
Bash kworker
tty_write()
file_tty_write()
n_tty_write()
uart_write()
__uart_start()
pm_runtime_get() // wakeup waker
queue_work()
pm_runtime_work()
rpm_resume()
status = RPM_RESUMING
serial_port_runtime_resume()
port->ops->start_tx()
pl011_tx_chars()
uart_write_wakeup()
[…]
__uart_start()
pm_runtime_get() < 0 // because runtime status = RPM_RESUMING
// later data are not commit to the port driver
status = RPM_ACTIVE
rpm_idle() -> rpm_suspend()
This patch tries to fix this by checking the port busy before entering
runtime suspending. A runtime_suspend callback is added for the port
driver. When entering runtime suspend the callback is invoked, if there's
still pending chars in the buffer then flush the buffer.
Fixes: 84a9582fd203 ("serial: core: Start managing serial controllers to enable runtime PM")
Cc: stable <[email protected]>
Reviewed-by: Tony Lindgren <[email protected]>
Reviewed-by: Andy Shevchenko <[email protected]>
Signed-off-by: Yicong Yang <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
When userspace opens the console, we call set_termios() passing a
termios with the console's configured baud rate. Currently this causes
dw8250_set_termios() to disable and then re-enable the UART clock at
the same frequency as it was originally. This can cause corruption
of any concurrent console output. Fix it by skipping the reclocking
if we are already at the correct rate.
Signed-off-by: Peter Collingbourne <[email protected]>
Fixes: 4e26b134bd17 ("serial: 8250_dw: clock rate handling for all ACPI platforms")
Cc: [email protected]
Reviewed-by: Andy Shevchenko <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
When about to transmit the function imx_uart_start_tx is called and in
some RS485 configurations this function will call imx_uart_stop_rx. The
problem is that imx_uart_stop_rx will enable loopback in order to
release the RS485 bus, but when loopback is enabled transmitted data
will just be looped to RX.
This patch fixes the above problem by not enabling loopback when about
to transmit.
This driver now works well when used for RS485 half duplex master
configurations.
Fixes: 79d0224f6bf2 ("tty: serial: imx: Handle RS485 DE signal active high")
Cc: stable <[email protected]>
Signed-off-by: Rickard x Andersson <[email protected]>
Tested-by: Christoph Niedermaier <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The port lock is a spinlock_t which is becomes a sleeping lock on PREEMPT_RT.
The driver splits the locking function into two parts: local_irq_save() and
uart_port_lock() and this breaks PREEMPT_RT.
Delay handling sysrq until port lock is dropped.
Remove the special case in the console write routine an always use the
complete locking function.
Signed-off-by: Sebastian Andrzej Siewior <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The struct eg20t_port has a spinlock_t which is used for locking while
access I/O of the device. Then there is the uart_portlock which is
sometimes and nests within eg20t_port's lock.
The uart_port lock is not used while using the struct in
pch_uart_hal_read() which might be okay. Then both locks are used in
pch_console_write() which looks odd especially the double try_lock part.
All in all it looks like the uart_port's lock could replace eg20t_port's
lock and simplify the code.
Remove eg20t_port::lock and use uart_port's lock for the lock scope.
Signed-off-by: Sebastian Andrzej Siewior <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
There is no need to directly initialize the spinlock_t in struct
uart_port. The structure is later passed to uart_add_one_port() which
initialize the complete struct including the lock member.
Remove spin_lock_init() on uart_port's internal lock.
Signed-off-by: Sebastian Andrzej Siewior <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The interrupt service routine is always invoked with disabled
interrupts.
Remove the _irqsave() from the locking functions in the interrupts
service routine/ pch_uart_interrupt().
Signed-off-by: Sebastian Andrzej Siewior <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
push_rx() returns always 0.
Make push_rx() return void.
Signed-off-by: Sebastian Andrzej Siewior <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
handle_rx() is only a wrapper around handle_rx_to() without any
additional functionality.
Invoke handle_rx_to() directly and remove handle_rx().
Signed-off-by: Sebastian Andrzej Siewior <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The port lock is a spinlock_t which is becomes a sleeping lock on PREEMPT_RT.
The driver splits the locking function into two parts: local_irq_save() and
uart_port_lock() and this breaks PREEMPT_RT.
Handle sysrq requests sysrq once the port lock is dropped.
Remove the special case in the console write routine an always use the
complete locking function.
Cc: Palmer Dabbelt <[email protected]>
Cc: Paul Walmsley <[email protected]>
Cc: [email protected]
Signed-off-by: Sebastian Andrzej Siewior <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The port lock is a spinlock_t which is becomes a sleeping lock on PREEMPT_RT.
The driver splits the locking function into two parts: local_irq_save() and
uart_port_lock() and this breaks PREEMPT_RT.
Handle sysrq requests sysrq once the port lock is dropped.
Remove the special case in the console write routine an always use the
complete locking function.
Cc: Manivannan Sadhasivam <[email protected]>
Cc: [email protected]
Cc: [email protected]
Signed-off-by: Sebastian Andrzej Siewior <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The port lock is a spinlock_t which is becomes a sleeping lock on PREEMPT_RT.
The driver splits the locking function into two parts: local_irq_save() and
uart_port_lock() and this breaks PREEMPT_RT.
Handle sysrq requests sysrq once the port lock is dropped.
Remove the special case in the console write routine an always use the
complete locking function.
Cc: Andreas Färber <[email protected]>
Cc: Manivannan Sadhasivam <[email protected]>
Cc: [email protected]
Cc: [email protected]
Signed-off-by: Sebastian Andrzej Siewior <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The port lock is a spinlock_t which is becomes a sleeping lock on PREEMPT_RT.
The driver splits the locking function into two parts: local_irq_save() and
uart_port_lock() and this breaks PREEMPT_RT.
Handle sysrq requests sysrq once the port lock is dropped.
Remove the special case in the console write routine an always use the
complete locking function.
Cc: Vladimir Zapolskiy <[email protected]>
Cc: [email protected]
Signed-off-by: Sebastian Andrzej Siewior <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The port lock is a spinlock_t which is becomes a sleeping lock on PREEMPT_RT.
The driver splits the locking function into two parts: local_irq_save() and
uart_port_lock() and this breaks PREEMPT_RT.
Delay handling sysrq until port lock is dropped.
Remove the special case in the console write routine an always use the
complete locking function.
Cc: Hammer Hsieh <[email protected]>
Signed-off-by: Sebastian Andrzej Siewior <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The port lock is a spinlock_t which is becomes a sleeping lock on PREEMPT_RT.
The driver splits the locking function into two parts: local_irq_save() and
uart_port_lock() and this breaks PREEMPT_RT.
Delay handling sysrq until port lock is dropped.
Remove the special case in the console write routine an always use the
complete locking function.
Signed-off-by: Sebastian Andrzej Siewior <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The port lock is a spinlock_t which is becomes a sleeping lock on PREEMPT_RT.
The driver splits the locking function into two parts: local_irq_save() and
uart_port_lock() and this breaks PREEMPT_RT.
Delay handling sysrq until port lock is dropped.
Remove the special case in the console write routine an always use the
complete locking function.
Signed-off-by: Sebastian Andrzej Siewior <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The port lock is a spinlock_t which is becomes a sleeping lock on PREEMPT_RT.
The driver splits the locking function into two parts: local_irq_save() and
uart_port_lock() and this breaks PREEMPT_RT.
Delay handling sysrq until port lock is dropped.
Remove the special case in the console write routine an always use the
complete locking function.
Cc: Bjorn Andersson <[email protected]>
Cc: Konrad Dybcio <[email protected]>
Cc: [email protected]
Signed-off-by: Sebastian Andrzej Siewior <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The port lock is a spinlock_t which is becomes a sleeping lock on PREEMPT_RT.
The driver splits the locking function into two parts: local_irq_save() and
uart_port_lock() and this breaks PREEMPT_RT.
Delay handling sysrq until port lock is dropped.
Remove the special case in the console write routine an always use the
complete locking function.
Cc: Kevin Hilman <[email protected]>
Cc: Jerome Brunet <[email protected]>
Cc: [email protected]
Cc: [email protected]
Signed-off-by: Sebastian Andrzej Siewior <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The port lock is a spinlock_t which is becomes a sleeping lock on PREEMPT_RT.
The driver splits the locking function into two parts: local_irq_save() and
uart_port_lock() and this breaks PREEMPT_RT.
Delay handling sysrq until port lock is dropped.
Remove the special case in the console write routine an always use the
complete locking function.
Signed-off-by: Sebastian Andrzej Siewior <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The port lock is a spinlock_t which is becomes a sleeping lock on PREEMPT_RT.
The driver splits the locking function into two parts: local_irq_save() and
uart_port_lock() and this breaks PREEMPT_RT.
Delay handling sysrq until port lock is dropped.
Remove the special case in the console write routine an always use the
complete locking function.
Signed-off-by: Sebastian Andrzej Siewior <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The port lock is a spinlock_t which is becomes a sleeping lock on PREEMPT_RT.
The driver splits the locking function into two parts: local_irq_save() and
uart_port_lock() and this breaks PREEMPT_RT.
Delay handling sysrq until port lock is dropped.
Remove the special case in the console write routine an always use the
complete locking function.
Cc: Russell King <[email protected]>
Signed-off-by: Sebastian Andrzej Siewior <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Instead of silently giving up, at least tell what the problem is.
Signed-off-by: Uwe Kleine-König <[email protected]>
Reviewed-by: Ilpo Järvinen <[email protected]>
Reviewed-by: Andy Shevchenko <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The serial8250_update_uartclk() body was created based on the several
method calls copied from the serial8250_do_set_termios() function. Seeing
aside with some other things the later method can update the baud rate
based on the new reference clock let's just call it instead thus
simplifying the code a bit.
Suggested-by: Andy Shevchenko <[email protected]>
Link: https://lore.kernel.org/linux-serial/[email protected]
Signed-off-by: Serge Semin <[email protected]>
Reviewed-by: Andy Shevchenko <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Since commit 1f2bcb8c8ccd ("gpio: protect the descriptor label with
SRCU") gpiod_set_consumer_name() calls synchronize_srcu() which led to
a "sleeping in atomic context" smatch warning.
This function (along with gpiod_get/put() and all other GPIO APIs apart
from gpiod_get/set_value() and gpiod_direction_input/output()) should
have never been called with a spinlock taken. We're only fixing this now
as GPIOLIB has been rebuilt to use SRCU for access serialization which
uncovered this problem.
Move the calls to gpiod_get/put() outside the spinlock critical section.
Reported-by: Dan Carpenter <[email protected]>
Closes: https://lore.kernel.org/linux-gpio/[email protected]/
Signed-off-by: Bartosz Golaszewski <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Currently for platforms which passes UART fifosize from DT gets
override by local driver structure "s3c24xx_serial_drv_data",
which is not intended. Change the code to honor fifosize from
device tree at first.
Signed-off-by: Tamseel Shams <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Compiling a kernel for the ColdFire causes a compiler warning:
drivers/tty/serial/mcf.c:473:12: warning: no previous prototype for
‘early_mcf_setup’ [-Wmissing-prototypes]
473 | int __init early_mcf_setup(struct mcf_platform_uart *platp)
| ^~~~~~~~~~~~~~~
This function seems to be completely unused, so let's remove it
to silence the warning.
Signed-off-by: Thomas Huth <[email protected]>
Reviewed-by: Jiri Slaby <[email protected]>
Acked-by: Greg Ungerer <[email protected]>
Reviewed-by: Geert Uytterhoeven <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
We are not supposed to spread quirks in 8250_port module especially
when we have a separate driver for the hardware in question.
Move quirk from generic module to the driver that uses it.
While at it, move IO to ->set_divisor() callback as it has to be from
day 1. ->get_divisor() is not supposed to perform any IO as UART port:
- might not be powered on
- is not locked by a spin lock
Fixes: 1ed67ecd1349 ("8250: microchip: Add 4 Mbps support in PCI1XXXX UART")
Signed-off-by: Andy Shevchenko <[email protected]>
Acked-by: Rengarajan S <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Update header inclusions to follow IWYU (Include What You Use)
principle.
Signed-off-by: Andy Shevchenko <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
8250 PCI library provides a common code to map and assign resources.
Use it in order to deduplicate existing code and support IO port
variants.
Signed-off-by: Andy Shevchenko <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
SIMPLE_DEV_PM_OPS() is deprecated, replace it with DEFINE_SIMPLE_DEV_PM_OPS()
and use pm_sleep_ptr() for setting the driver's PM routines. We can now
remove the __maybe_unused qualifier in the suspend and resume functions.
Signed-off-by: Andy Shevchenko <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Use generic function to set firmware node instead of ACPI specific one.
Signed-off-by: Andy Shevchenko <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
While now there is no issue if IRQ is fired before we clearing
the interrupts as the handler does the same, but strictly speaking
it might be problematic if IRQ handler wants to do something more.
Move clearing interrupt code to be called before registering the
IRQ handler.
Signed-off-by: Andy Shevchenko <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
PM callbacks take struct device pointer as a parameter, use
dev_get_drvdata() to retrieve it instead of unneeded double
loop of referencing via pci_get_drvdata(to_pci_dev(dev)).
Signed-off-by: Andy Shevchenko <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
It seems a copy&paste mistake that suspend callback removes the GPIO
device. There is no counterpart of this action, means once suspended
there is no more GPIO device available untile full unbind-bind cycle
is performed. Remove suspicious GPIO device removal in suspend.
Fixes: d0aeaa83f0b0 ("serial: exar: split out the exar code from 8250_pci")
Signed-off-by: Andy Shevchenko <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
We need the tty/serial fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
mips_ejtag_fdc_encode() method expects having a first argument passed of
the "u8 **" type, meanwhile the driver passes the "const char **" type.
That causes the next build-warning:
drivers/tty/mips_ejtag_fdc.c: In function ‘mips_ejtag_fdc_console_write’:
drivers/tty/mips_ejtag_fdc.c:343:32: error: passing argument 1 of ‘mips_ejtag_fdc_encode’ from incompatible pointer type [-Werror=incompatible-pointer-types]
word = mips_ejtag_fdc_encode(&buf_ptr, &buf_len, 1);
^
drivers/tty/mips_ejtag_fdc.c:216:24: note: expected ‘const u8 ** {aka const unsigned char **}’ but argument is of type ‘const char **’
static struct fdc_word mips_ejtag_fdc_encode(const u8 **ptrs,
^~~~~~~~~~~~~~~~~~~~~
Fix it by altering the type of the pointer which is passed to the
mips_ejtag_fdc_encode() method.
Fixes: ce7cbd9a6c81 ("tty: mips_ejtag_fdc: use u8 for character pointers")
Signed-off-by: Serge Semin <[email protected]>
Signed-off-by: Thomas Bogendoerfer <[email protected]>
|
|
When DMA is used in RS485 mode make sure that the UARTs tx section is
enabled before the DMA buffers are queued for transmission.
Cc: [email protected]
Fixes: 8d479237727c ("serial: amba-pl011: add RS485 support")
Signed-off-by: Lino Sanfilippo <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Before commit 07c30ea5861f ("serial: Do not hold the port lock when setting
rx-during-tx GPIO") the SER_RS485_RX_DURING_TX flag was only set if the
rx-during-tx mode was not controlled by a GPIO. Now the flag is set
unconditionally when RS485 is enabled. This results in an incorrect setting
if the rx-during-tx GPIO is not asserted.
Fix this by setting the flag only if the rx-during-tx mode is not
controlled by a GPIO and thus restore the correct behaviour.
Cc: [email protected] # 6.6+
Fixes: 07c30ea5861f ("serial: Do not hold the port lock when setting rx-during-tx GPIO")
Signed-off-by: Lino Sanfilippo <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The new SBI console has the same problem as the old one: there's only
one shared backing hardware and no synchronization, so the two drivers
end up stepping on each other. This was the same issue the old SBI-0.1
console drivers had, but that was disabled by default when SBI-0.1 was.
So just mark the new driver as nonportable.
Reported-by: Emil Renner Berthing <[email protected]>
Fixes: 88ead68e764c ("tty: Add SBI debug console support to HVC SBI driver")
Signed-off-by: Palmer Dabbelt <[email protected]>
Reviewed-by: Paul Walmsley <[email protected]>
Reviewed-by: Anup Patel <[email protected]>
Reviewed-by: Conor Dooley <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Note that pmz_detach() is only called once pmz_attach() was successfully
called. In that case platform_set_drvdata() was called and so
platform_get_drvdata() won't return NULL. This allows to drop the
respective check and so get rid of the only error path in pmz_detach().
After that the driver can be trivially converted from always returning
zero in the remove callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <[email protected]>
Link: https://lore.kernel.org/r/90b9a65ad8800b4d047aa5219959008a01588a94.1708246007.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <[email protected]>
Link: https://lore.kernel.org/r/60d0657daf8f4f9e2e3e282941ba542f08dc7f96.1708246007.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <[email protected]>
Link: https://lore.kernel.org/r/f2ad92c97086c42dab23cdb165d9f978bbf3d3b5.1708246007.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
We need the serial/tty fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
There's no need to include linux/tty_buffer.h in linux/tty.h.
Move the include into tty_buffer.c that is actually using it.
Signed-off-by: Ilpo Järvinen <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
We are not supposed to spread quirks in 8250_port module especially
when we have a separate driver for the hardware in question.
Move quirk from generic module to the driver that uses it.
Signed-off-by: Andy Shevchenko <[email protected]>
Reviewed-by: Ilpo Järvinen <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The variable linestate being assigned a value that is never read, the
following continue statement jumps to the end of the while-loop and then
it is re-assigned a new value. The assignment is redundant and can be
removed.
Cleans up clang scan build warning:
drivers/tty/serial/jsm/jsm_cls.c:398:4: warning: Value stored
to 'linestatus' is never read [deadcode.DeadStores]
Signed-off-by: Colin Ian King <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Variable hsu_rate is being checked for an upper limit and is assigned
a value that is never read. The if statement and assignment are
redundant and can be removed.
Cleans up clang scan build warning:
drivers/tty/serial/lpc32xx_hs.c:237:3: warning: Value stored
to 'hsu_rate' is never read [deadcode.DeadStores]
Signed-off-by: Colin Ian King <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Replace custom unit definitions that are available via units.h.
Signed-off-by: Andy Shevchenko <[email protected]>
Reviewed-by: Ilpo Järvinen <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Update header inclusions to follow IWYU (Include What You Use)
principle.
Signed-off-by: Andy Shevchenko <[email protected]>
Reviewed-by: Jiri Slaby <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|