| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
If FIFO depth DT property is provided, check it matches what hardware
reports and warn otherwise. Else, use hardware provided value.
Hardware exposes FIFO depth indirectly because
CQSPI_REG_SRAMPARTITION is partially read-only.
Move probe cqspi->ddata assignment prior to cqspi_of_get_pdata() call.
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20240423-cdns-qspi-mbly-v4-1-3d2a7b535ad0@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use the scope based of_node_put() cleanup in s3c64xx_spi_csinfo to
automatically release the device node with the __free() cleanup handler
Initialize data_np at the point of declaration for clarity of scope.
This change reduces the risk of memory leaks and simplifies the code by
removing manual node put call.
Suggested-by: Julia Lawall <julia.lawall@inria.fr>
Signed-off-by: Shivani Gupta <shivani07g@gmail.com>
Link: https://lore.kernel.org/r/20240418000505.731724-1-shivani07g@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In some cases SPI child devices behind spi-mux require different
settings like: max_speed_hz, mode and bits_per_word.
Typically the slave device driver puts the settings in place and calls
spi_setup() once during probe and assumes they stay in place for all
following spi transfers.
However spi-mux forwarded spi_setup() -call to SPI master driver only
when slave driver calls spi_setup(). If second slave device was
accessed meanwhile and that driver called spi_setup(), the
settings did not change back to the first spi device.
In case of wrong max_speed_hz this caused spi trasfers to fail.
This commit adds spi_setup() call after mux is changed. This way
the right device specific parameters are set to the master driver.
The fix has been tested by using custom hardware and debugging
spi master driver speed settings.
Co-authored-by: Petri Tauriainen <petri.tauriainen@bittium.com>
Signed-off-by: Heikki Keranen <heikki.keranen@bittium.com>
Link: https://lore.kernel.org/r/20240422114150.84426-1-heikki.keranen@bittium.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fixes: 439fbc97502a ("spi: cs42l43: Add bridged cs35l56 amplifiers")
Signed-off-by: Maciej Strozek <mstrozek@opensource.cirrus.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20240418103315.1487267-1-mstrozek@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
of_gpio.h is deprecated and subject to remove.
The driver doesn't use it, simply remove the unused header.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240417104730.2510856-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use devm_add_action_or_reset() rather than manually cleaning up on the
error path.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20240417093026.79396-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Merge series from Charles Keepax <ckeepax@opensource.cirrus.com>:
In some cs42l43 systems a couple of cs35l56 amplifiers are attached
to the cs42l43's SPI and I2S. On Windows the cs42l43 is controlled
by a SDCA class driver and these two amplifiers are controlled by
firmware running on the cs42l43. However, under Linux the decision
was made to interact with the cs42l43 directly, affording the user
greater control over the audio system. However, this has resulted
in an issue where these two bridged cs35l56 amplifiers are not
populated in ACPI and must be added manually. There is at least an
SDCA extension unit DT entry we can key off.
The process of adding this is handled using a software node, firstly the
ability to add native chip selects to software nodes must be added.
Secondly, an additional flag for naming the SPI devices is added this
allows the machine driver to key to the correct amplifier. Then finally,
the cs42l43 SPI driver adds the two amplifiers directly onto its SPI
bus.
An additional series will follow soon to add the audio machine driver
parts (in the sof-sdw driver), however that is fairly orthogonal to
this part of the process, getting the actual amplifiers registered.
|
|
Merge series from Andy Shevchenko <andriy.shevchenko@linux.intel.com>:
A couple of additional refactorings on top of the multi-CS support.
One is to make sure that the comment and the code are not disrupted
if additional changes come in the future and second one is f or the
sake of deduplication. In both cases it also makes indentation level
smaller in the affected pieces of the code.
No functional changes intended.
|
|
On some cs42l43 systems a couple of cs35l56 amplifiers are attached
to the cs42l43's SPI and I2S. On Windows the cs42l43 is controlled
by a SDCA class driver and these two amplifiers are controlled by
firmware running on the cs42l43. However, under Linux the decision
was made to interact with the cs42l43 directly, affording the user
greater control over the audio system. However, this has resulted
in an issue where these two bridged cs35l56 amplifiers are not
populated in ACPI and must be added manually.
Check for the presence of the "01fa-cirrus-sidecar-instances" property
in the SDCA extension unit's ACPI properties to confirm the presence
of these two amplifiers and if they exist add them manually onto the
SPI bus.
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Maciej Strozek <mstrozek@opensource.cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20240416100904.3738093-5-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Update the name for software node based SPI devices to use the fwnode
name as the device name. This is helpful since swnode devices are
usually added within the kernel, and the kernel often then requires a
predictable name such that it can refer back to the device.
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20240416100904.3738093-4-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use is_acpi_device_node() rather than checking ACPI_COMPANION(), such
that when checking for other types of firmware node, the code can
consistently do checks against the fwnode.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20240416100904.3738093-3-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Due to the reading of FIFO during the dump of data registers in
debugfs, if SPI transmission is in progress, it will be affected
and may result in transmission failure. Therefore, the dump
interface of data registers in debugfs is removed.
Fixes: 2b2142f247eb ("spi: hisi-kunpeng: Add debugfs support")
Signed-off-by: Devyn Liu <liudingyuan@huawei.com>
Reviewed-by: Jay Fang <f.fangjian@huawei.com>
Link: https://lore.kernel.org/r/20240416015839.3323398-1-liudingyuan@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
For some reason the commit 1209c5566f9b ("spi: Consistently use BIT
for cs_index_mask") missed one place to change, do it here to finish
the job.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240415184757.1198149-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In order of deduplication and better maintenance introduce a new
spi_for_each_valid_cs() helper macro.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240415193340.1279360-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The multi-CS support splits the comment and the code in the spi_set_cs().
To avoid this in the future extract spi_toggle_csgpiod() helper.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240415193340.1279360-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
There is no need to allocate chip_data and then validate number of
CS pins as it will have the same effect. Hence move number of CS pins
validation out of condition in setup().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240403171550.1074644-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The ID table already has respective entry and MODULE_DEVICE_TABLE and
creates proper alias for platform driver. Having another MODULE_ALIAS
causes the alias to be duplicated.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20240414154859.126931-1-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The version format string in the AXI SPI Engine driver was probably
intended to print the version number in the same format as the DT
compatible string (e.g. 1.00.a). However, the version just uses
semantic versioning so formatting the patch number as a character
is not correct and would result in printing control characters for
patch numbers less than 32.
Fixes: b1353d1c1d45 ("spi: Add Analog Devices AXI SPI Engine controller support")
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20240412-axi-spi-engine-version-printf-v1-1-95e1e842c1a6@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Refactor code for "is the node's child available?" check by using the
corresponding macro instead, which reads more clearly.
While at it, use scope-based cleanup instead of manual of_node_put()
calls when getting platform data through cdns_xspi_of_get_plat_data().
This removes the unnecessary "node_child" declaration out of the loop's
scope and auto cleans up "node_child" when it goes out of scope, even
when we return early due to error.
Signed-off-by: Kousik Sanagavarapu <five231003@gmail.com>
Link: https://msgid.link/r/20240410130205.179069-1-five231003@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
cqspi_enable_dtr() is called for each operation, commands or not, reads
or writes. It writes CQSPI_REG_CONFIG then waits for idle (three
successful reads). Skip that in the no-DTR case if DTR is already
disabled.
It cannot be skipped in the DTR case as cqspi_setup_opcode_ext() writes
to a register and we must wait for idle state.
According to ftrace, the average cqspi_exec_mem_op() call goes from
85.4µs to 83.6µs when reading 235M over UBIFS on an octal flash.
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://msgid.link/r/20240405-cdns-qspi-mbly-v2-6-956679866d6d@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Avoid of_device_get_match_data() call on each IRQ and each read
operation. Store pointer in `struct cqspi_st` device instance.
End-to-end performance measurements improve with this patch. On a given
octal flash, reading 235M over UBIFS is ~3.4% faster. During that read,
the average cqspi_exec_mem_op() call goes from 85.4µs to 80.7µs
according to ftrace. The worst case goes from 622.4µs to 615.2µs.
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://msgid.link/r/20240405-cdns-qspi-mbly-v2-4-956679866d6d@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The Cadence QSPI Controller driver is used on Mobileye EyeQ5 platform.
Allow building on MIPS.
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://msgid.link/r/20240405-cdns-qspi-mbly-v2-3-956679866d6d@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In function pci1xxxx_spi_probe, there is a potential null pointer that
may be caused by a failed memory allocation by the function devm_kzalloc.
Hence, a null pointer check needs to be added to prevent null pointer
dereferencing later in the code.
To fix this issue, spi_bus->spi_int[iter] should be checked. The memory
allocated by devm_kzalloc will be automatically released, so just directly
return -ENOMEM without worrying about memory leaks.
Fixes: 1cc0cbea7167 ("spi: microchip: pci1xxxx: Add driver for SPI controller of PCI1XXXX PCIe switch")
Signed-off-by: Huai-Yuan Liu <qq810974084@gmail.com>
Link: https://msgid.link/r/20240403014221.969801-1-qq810974084@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
devm_spi_alloc_controller will allocate an SPI controller and
automatically release a reference on it when dev is unbound from
its driver. It doesn't need to call spi_controller_put explicitly
to put the reference when lpspi driver failed initialization.
Fixes: 2ae0ab0143fc ("spi: lpspi: Avoid potential use-after-free in probe()")
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Link: https://msgid.link/r/20240403084029.2000544-1-carlos.song@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
pxa_ssp_request() implies a reference counting, hence the pxa_ssp_free()
must be called when we are done. Add missed call.
Fixes: bb77c99ee6d3 ("spi: pxa2xx: Skip SSP initialization if it's done elsewhere")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://msgid.link/r/20240402144523.3402063-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
If the SPI data size is smaller than FIFO, it operates in PIO mode,
and if it is larger than FIFO size, it oerates in DMA mode.
If the SPI data size is equal to fifo, it operates in PIO mode and it is
separated to 2 transfers. To prevent it, it must operate in DMA mode
from the case where the data size and the fifo size are the same.
Fixes: 1ee806718d5e ("spi: s3c64xx: support interrupt based pio mode")
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20240329085840.65856-1-jaewon02.kim@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Merge series from David Lechner <dlechner@baylibre.com>:
I found a couple more controller drivers that were checking if the
tx_buf and rx_buf fields in the spi_transfer structure were set by a
peripheral driver that I missed in [1]. These checks can be removed
as well.
[1]: https://lore.kernel.org/linux-spi/20240325-spi-remove-is_dma_mapped-v2-1-d08d62b61f1c@baylibre.com/
|
|
Merge series from Louis Chauvet <louis.chauvet@bootlin.com>:
This series adds the support for the omap-mcspi multi mode which allows
sending SPI messages with a shorter delay between CS and the message.
One drawback of the multi-mode is that the CS is raised between each word,
so it can only be used with messages containing 1 word transfers and
asking for cs_change. Few devices, like FPGAs, may easily workaround this
limitation.
The first patch removes the current implementation, which is working, but
don't comply with what is asked in the spi transfer (The CS is raised by
the hardware regardless of cs_change state). No drivers or board file use this
implementation upstream.
The second patch adds the implementation of the multi-mode, which complies
with what is asked in the SPI message.
The third patch is the suggested optimization for using MULTI mode in more
situations.
|
|
There are no more peripheral drivers that set t->tx_dma or t->rx_dma.
Therefore, is_dma_mapped is always false and can be removed.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://msgid.link/r/20240328-spi-more-tx-rx-buf-cleanup-v1-2-9ec1ceedf08c@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
There are no more peripheral drivers that set t->tx_dma or t->rx_dma so
these will always == 0. Therefore, we can remove these checks since
they are always true.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://msgid.link/r/20240328-spi-more-tx-rx-buf-cleanup-v1-1-9ec1ceedf08c@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
If SSP has been enumerated elsewhere, skip its initialization
in pxa2xx_spi_init_pdata().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://msgid.link/r/20240327193138.2385910-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Refactor pxa2xx_spi_init_pdata() by extracting a new
pxa2xx_spi_init_ssp() helper which makes code less
twisted. It will be easier to continue refactoring for
a new coming modification.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://msgid.link/r/20240327193138.2385910-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Drop rather useless use of ACPI_PTR() and of_match_ptr().
It also removes the necessity to be dependent of.h inclusion.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://msgid.link/r/20240327193138.2385910-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The PCI || ACPI dependency is the historical part of the x86 support.
Narrow the Kconfig option visibility by limiting this dependency to x86.
The drop of x86 for PCI case had happened in the commit 2b49ebda39d6
("spi/pxa2xx: allow building on a 64-bit kernel"), while the ACPI
was specifically added for Intel Lynx Point in the commit a3496855d9f1
("spi/pxa2xx: add support for Lynxpoint SPI controllers").
Note that X86 covers both 32- and 64-bit variants.
Suggested-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://msgid.link/r/20240327193138.2385910-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Enable multimode when a transfer of multiple small words can be
transformed in a transfer with a single bigger word. This is allowed as
long as the result on the cable is the same, so word_delay must be zero.
Signed-off-by: Louis Chauvet <louis.chauvet@bootlin.com>
Link: https://msgid.link/r/20240327-spi-omap2-mcspi-multi-mode-v3-3-c4ac329dd5a2@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Introduce support for MULTI-mode in the OMAP2 MCSPI driver. Currently, the
driver always uses SINGLE mode to handle the chip select (CS). With this
enhancement, MULTI-mode is enabled for specific messages, allowing for a
shorter delay between CS enable and the message (some FPGA devices are
sensitive to this delay).
The OMAP2 MCSPI device can use two different mode to send messages, SINGLE
and MULTI:
In SINGLE mode, the controller only leverages one single FIFO, and the
host system has to manually select the CS it wants to enable.
In MULTI mode, each CS is bound to a FIFO, the host system then writes the
data to the relevant FIFO, as the hardware will take care of the CS
The drawback of multi-mode is that it's not possible to keep the CS
enabled between each words. Therefore, this patch enables multi-mode only
for specific messages: the spi_message must contain only spi_transfer of 1
word (of any size) with cs_change enabled.
A new member is introduced in the omap2_mcspi structure to keep track of
the current used mode.
Signed-off-by: Louis Chauvet <louis.chauvet@bootlin.com>
Link: https://msgid.link/r/20240327-spi-omap2-mcspi-multi-mode-v3-2-c4ac329dd5a2@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Commit 5cbc7ca987fb ("spi: spi-omap2-mcspi.c: Toggle CS after each
word") introduced the toggling of CS after each word for the omap2-mcspi
controller.
The implementation is not respectful of the actual spi_message
content, so the CS can be raised after each word even if the
transfer structure asks to keep the CS active for the whole operation.
As it is not used anyway in the current Linux tree, it can be safely
removed.
Signed-off-by: Louis Chauvet <louis.chauvet@bootlin.com>
Link: https://msgid.link/r/20240327-spi-omap2-mcspi-multi-mode-v3-1-c4ac329dd5a2@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Core in platform_driver_register() already sets the .owner, so driver
does not need to.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://msgid.link/r/20240327174737.519637-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Core in platform_driver_register() already sets the .owner, so driver
does not need to.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://msgid.link/r/20240327174737.519637-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Core in spi_register_driver() already sets the .owner, so driver
does not need to.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://msgid.link/r/20240327174737.519637-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Switch to use dev_err_probe() to simplify the error path and
unify a message template.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://msgid.link/r/20240326181027.1418989-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
There are no more users of the deprecated is_dma_mapped in struct
spi_message so it can be removed.
References in documentation and comments are also removed.
A few similar checks if xfer->tx_dma or xfer->rx_dma are not NULL are
also removed since these are now guaranteed to be NULL because they
were previously set only if is_dma_mapped was true.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://msgid.link/r/20240325-spi-remove-is_dma_mapped-v2-1-d08d62b61f1c@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add support to the SPI controller driver to use SPI MEM framework.
SPI subsystem utilizing the SPI memory operations allows to re-use
SPI controller drivers for both SPI NOR devices, regular SPI devices
as well as SPI NAND devices.
Add below functions of spi_mem_ops to support SPI MEM framework
- exec-op(): to execute the memory operations.
- supports_op(): to check if the memory operation is supported.
- adjust_op_size(): to split data transfers so that they don’t exceed the
max transfer size supported by the controller.
Suggested-by: Sudheesh Mavila <sudheesh.mavila@amd.com>
Co-developed-by: Krishnamoorthi M <krishnamoorthi.m@amd.com>
Signed-off-by: Krishnamoorthi M <krishnamoorthi.m@amd.com>
Co-developed-by: Akshata MukundShetty <akshata.mukundshetty@amd.com>
Signed-off-by: Akshata MukundShetty <akshata.mukundshetty@amd.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Link: https://msgid.link/r/20240229134544.3461757-1-Raju.Rangoju@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
No in-kernel users of struct rspi_plat_data. If required,
the software nodes should be used for such users. For now
just get rid of it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://msgid.link/r/20240325142118.3210915-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
All the spi_transfer variables in this file use the name "xfer" except
the one in mtk_spi_interrupt(). Align the naming for consistency and
easier searching.
While at it, reformat one memcpy() usage since the coding style allows
100 column lines today.
This commit has no functional change.
Signed-off-by: Fei Shao <fshao@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://msgid.link/r/20240321070942.1587146-3-fshao@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Extract a magic number, from mt7621_spi_probe(), used to
declare the number of chip select lines (which co-incides
with the native chip select count of 2) to a macro.
Use the newly defined MT7621_NATIVE_CS_COUNT macro to
instead populate both the spi_controller's max_native_cs
and num_chipselect members.
Declare that the spi_controller should use_gpio_descriptors
if present in the device properties (such as those declared
in the cs-gpio property of a "ralink,mt7621-spi" compatible
device-tree node) so that the SPI core will recalculcate
num_chipselect to account for the GPIO descriptors that
it should have populated in the cs_gpiod array member.
Remove the assignment of mt7621_spi_transfer_one_message()
to the spi_controller's transfer_one_message hook.
Refactor the mt7621_spi_transfer_one_message() logic into
mt7621_spi_prepare_message() and mt7621_spi_transfer_one()
and assign both to the spi_controller's prepare_message
and transfer_one hooks respectively.
Migrate the call mt7621_spi_transfer_one_message() made to
mt7621_spi_flush() just before chip select deactivation,
to the end of mt7621_spi_write_half_duplex() to ensure
that any pending data is shifted out of MOSI before the SPI
core deactivates the chip select line.
As chip select activation is now taken care of by the SPI
core, due to the use of the transfer_one hook instead of
transfer_one_message, the calls to mt7621_spi_set_cs()
from mt7621_spi_transfer_one_message() have fallen away.
And although the SPI core will handle activation for GPIO
chip select lines behind the scenes, it requires a callback
to allow the driver to perform controller-specific
operations to control its native chip select lines.
Rename mt7621_spi_set_cs() to mt7621_spi_set_native_cs()
and make sure that it takes into account the activation
polarity of the chip select line it's acting upon, as the
passed enable parameter represents the desired line level
and not the desired activation state, and then assign
mt7621_set_cs() to the spi_controller's set_cs hook.
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
Link: https://msgid.link/r/20240316010302.20776-1-justin.swartz@risingedge.co.za
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A small collection of fixes that came in since the merge window. Most
of it is relatively minor driver specific fixes, there's also fixes
for error handling with SPI flash devices and a fix restoring delay
control functionality for non-GPIO chip selects managed by the core"
* tag 'spi-fix-v6.9-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: spi-mt65xx: Fix NULL pointer access in interrupt handler
spi: docs: spidev: fix echo command format
spi: spi-imx: fix off-by-one in mx51 CPU mode burst length
spi: lm70llp: fix links in doc and comments
spi: Fix error code checking in spi_mem_exec_op()
spi: Restore delays for non-GPIO chip select
spi: lpspi: Avoid potential use-after-free in probe()
|
|
The TX buffer in spi_transfer can be a NULL pointer, so the interrupt
handler may end up writing to the invalid memory and cause crashes.
Add a check to trans->tx_buf before using it.
Fixes: 1ce24864bff4 ("spi: mediatek: Only do dma for 4-byte aligned buffers")
Signed-off-by: Fei Shao <fshao@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://msgid.link/r/20240321070942.1587146-2-fshao@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
c712c05e46c8 ("spi: imx: fix the burst length at DMA mode and CPU mode")
corrects three cases of setting the ECSPI burst length but erroneously
leaves the in-range CPU case one bit to big (in that field a value of
0 means 1 bit). The effect was that transmissions that should have been
8-bit bytes appeared as 9-bit causing failed communication with SPI
devices.
Link: https://lore.kernel.org/all/20240201105451.507005-1-carlos.song@nxp.com/
Link: https://lore.kernel.org/all/20240204091912.36488-1-carlos.song@nxp.com/
Fixes: c712c05e46c8 ("spi: imx: fix the burst length at DMA mode and CPU mode")
Signed-off-by: Adam Butcher <adam@jessamine.co.uk>
Link: https://msgid.link/r/20240318175119.3334-1-adam@jessamine.co.uk
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
An i.MX fix depends on other fixes that were sent to v6.8.
|