aboutsummaryrefslogtreecommitdiff
path: root/drivers/scsi
AgeCommit message (Collapse)AuthorFilesLines
2020-08-20scsi: mpt3sas: Add functions to check if any cmd is outstanding on Target ↵Suganath Prabu S3-19/+88
and LUN Add helper functions to check whether any SCSI command is outstanding on particular Target, LUN device. Also add function parameters 'channel', 'id' to function mpt3sas_scsih_issue_tm(). Link: https://lore.kernel.org/r/1596096229-3341-6-git-send-email-suganath-prabu.subramani@broadcom.com Signed-off-by: Suganath Prabu S <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]>
2020-08-20scsi: mpt3sas: Rename and export interrupt mask/unmask functionsSuganath Prabu S2-13/+13
Rename Function _base_unmask_interrupts() to mpt3sas_base_unmask_interrupts() and _base_mask_interrupts() to mpt3sas_base_mask_interrupts(). Also add function declarion to mpt3sas_base.h Link: https://lore.kernel.org/r/1596096229-3341-5-git-send-email-suganath-prabu.subramani@broadcom.com Signed-off-by: Suganath Prabu S <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]>
2020-08-20scsi: mpt3sas: Cancel the running work during host resetSuganath Prabu S2-5/+16
It is not recommended to issue back-to-back host reset without any delay. However, if someone issues back-to-back host reset then we observe that target devices get unregistered and re-register with SML. And if OS drive is behind the HBA when it gets unregistered, then file-system goes into read-only mode. Normally during host reset, driver marks accessible target devices as responding and triggers the event MPT3SAS_REMOVE_UNRESPONDING_DEVICES to remove any non-responding devices through FW worker thread. While processing this event, driver unregisters the non-responding devices and clears the responding flag for all the devices. Currently, during host reset, driver is cancelling only those Firmware event works which are pending in Firmware event workqueue. It is not cancelling work which is currently running. Change the driver to cancel all events. Link: https://lore.kernel.org/r/1596096229-3341-4-git-send-email-suganath-prabu.subramani@broadcom.com Signed-off-by: Suganath Prabu S <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]>
2020-08-20scsi: mpt3sas: Dump system registers for debuggingSuganath Prabu S1-0/+20
When controller fails to transition to READY state during driver probe, dump the system interface register set. This will give snapshot of the firmware status for debugging driver load issues. Link: https://lore.kernel.org/r/1596096229-3341-3-git-send-email-suganath-prabu.subramani@broadcom.com Signed-off-by: Suganath Prabu S <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]>
2020-08-20scsi: mpt3sas: Memset config_cmds.reply buffer with zerosSuganath Prabu S1-1/+1
Currently config_cmds.reply buffer is not memset to zero before posting config page request message. In some cases, for the current config request, the previous config reply is getting processed and we will observe PageType mismatch between request to reply buffer. It will be difficult to debug this type of issue and it confuses by thinking that HBA Firmware itself posted the wrong config reply. So it is better to memset the config_cmds.reply buffer with zeros before issuing the config request. Link: https://lore.kernel.org/r/1596096229-3341-2-git-send-email-suganath-prabu.subramani@broadcom.com Signed-off-by: Suganath Prabu S <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]>
2020-08-20scsi: ufs: Properly release resources if a task is aborted successfullyCan Guo1-4/+1
In current UFS task abort hook, namely ufshcd_abort(), if one task is aborted successfully, clk_gating.active_reqs held by this task is not decreased, which makes clk_gating.active_reqs stay above zero forever, thus clock gating would never happen. Instead of releasing resources of one task "manually", use the existing func __ufshcd_transfer_req_compl(). This change also eliminates a possible race of scsi_dma_unmap() from the real completion in IRQ handler path. Link: https://lore.kernel.org/r/[email protected] Fixes: 1ab27c9cf8b6 ("ufs: Add support for clock gating") CC: Stanley Chu <[email protected]> Reviewed-by: Stanley Chu <[email protected]> Reviewed-by: Asutosh Das <[email protected]> Signed-off-by: Can Guo <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]>
2020-08-17Revert "scsi: qla2xxx: Disable T10-DIF feature with FC-NVMe during probe"Quinn Tran1-4/+0
FCP T10-PI and NVMe features are independent of each other. This patch allows both features to co-exist. This reverts commit 5da05a26b8305a625bc9d537671b981795b46dab. Link: https://lore.kernel.org/r/[email protected] Fixes: 5da05a26b830 ("scsi: qla2xxx: Disable T10-DIF feature with FC-NVMe during probe") Reviewed-by: Himanshu Madhani <[email protected]> Signed-off-by: Quinn Tran <[email protected]> Signed-off-by: Nilesh Javali <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]>
2020-08-17Revert "scsi: qla2xxx: Fix crash on qla2x00_mailbox_command"Saurav Kashyap1-8/+0
FCoE adapter initialization failed for ISP8021 with the following patch applied. In addition, reproduction of the issue the patch originally tried to address has been unsuccessful. This reverts commit 3cb182b3fa8b7a61f05c671525494697cba39c6a. Link: https://lore.kernel.org/r/[email protected] Reviewed-by: Himanshu Madhani <[email protected]> Signed-off-by: Saurav Kashyap <[email protected]> Signed-off-by: Nilesh Javali <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]>
2020-08-17scsi: qla2xxx: Fix null pointer access during disconnect from subsystemQuinn Tran1-0/+5
NVMEAsync command is being submitted to QLA while the same NVMe controller is in the middle of reset. The reset path has deleted the association and freed aen_op->fcp_req.private. Add a check for this private pointer before issuing the command. ... 6 [ffffb656ca11fce0] page_fault at ffffffff8c00114e [exception RIP: qla_nvme_post_cmd+394] RIP: ffffffffc0d012ba RSP: ffffb656ca11fd98 RFLAGS: 00010206 RAX: ffff8fb039eda228 RBX: ffff8fb039eda200 RCX: 00000000000da161 RDX: ffffffffc0d4d0f0 RSI: ffffffffc0d26c9b RDI: ffff8fb039eda220 RBP: 0000000000000013 R8: ffff8fb47ff6aa80 R9: 0000000000000002 R10: 0000000000000000 R11: ffffb656ca11fdc8 R12: ffff8fb27d04a3b0 R13: ffff8fc46dd98a58 R14: 0000000000000000 R15: ffff8fc4540f0000 ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018 7 [ffffb656ca11fe08] nvme_fc_start_fcp_op at ffffffffc0241568 [nvme_fc] 8 [ffffb656ca11fe50] nvme_fc_submit_async_event at ffffffffc0241901 [nvme_fc] 9 [ffffb656ca11fe68] nvme_async_event_work at ffffffffc014543d [nvme_core] 10 [ffffb656ca11fe98] process_one_work at ffffffff8b6cd437 11 [ffffb656ca11fed8] worker_thread at ffffffff8b6cdcef 12 [ffffb656ca11ff10] kthread at ffffffff8b6d3402 13 [ffffb656ca11ff50] ret_from_fork at ffffffff8c000255 -- PID: 37824 TASK: ffff8fb033063d80 CPU: 20 COMMAND: "kworker/u97:451" 0 [ffffb656ce1abc28] __schedule at ffffffff8be629e3 1 [ffffb656ce1abcc8] schedule at ffffffff8be62fe8 2 [ffffb656ce1abcd0] schedule_timeout at ffffffff8be671ed 3 [ffffb656ce1abd70] wait_for_completion at ffffffff8be639cf 4 [ffffb656ce1abdd0] flush_work at ffffffff8b6ce2d5 5 [ffffb656ce1abe70] nvme_stop_ctrl at ffffffffc0144900 [nvme_core] 6 [ffffb656ce1abe80] nvme_fc_reset_ctrl_work at ffffffffc0243445 [nvme_fc] 7 [ffffb656ce1abe98] process_one_work at ffffffff8b6cd437 8 [ffffb656ce1abed8] worker_thread at ffffffff8b6cdb50 9 [ffffb656ce1abf10] kthread at ffffffff8b6d3402 10 [ffffb656ce1abf50] ret_from_fork at ffffffff8c000255 Link: https://lore.kernel.org/r/[email protected] Reviewed-by: Himanshu Madhani <[email protected]> Signed-off-by: Quinn Tran <[email protected]> Signed-off-by: Nilesh Javali <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]>
2020-08-17scsi: qla2xxx: Check if FW supports MQ before enablingSaurav Kashyap1-0/+5
OS boot during Boot from SAN was stuck at dracut emergency shell after enabling NVMe driver parameter. For non-MQ support the driver was enabling MQ. Add a check to confirm if FW supports MQ. Link: https://lore.kernel.org/r/[email protected] Reviewed-by: Himanshu Madhani <[email protected]> Signed-off-by: Saurav Kashyap <[email protected]> Signed-off-by: Nilesh Javali <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]>
2020-08-17scsi: qla2xxx: Fix WARN_ON in qla_nvme_register_hbaArun Easi2-1/+10
qla_nvme_register_hba() puts out a warning when there are not enough queue pairs available for FC-NVME. Just fail the NVME registration rather than a WARNING + call Trace. Link: https://lore.kernel.org/r/[email protected] Reviewed-by: Himanshu Madhani <[email protected]> Signed-off-by: Arun Easi <[email protected]> Signed-off-by: Nilesh Javali <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]>
2020-08-17scsi: qla2xxx: Allow ql2xextended_error_logging special value 1 to be set ↵Arun Easi1-0/+3
anytime ql2xextended_error_logging can now be set to 1 to get the default mask value, as opposed to at module load time only. Link: https://lore.kernel.org/r/[email protected] Reviewed-by: Himanshu Madhani <[email protected]> Signed-off-by: Arun Easi <[email protected]> Signed-off-by: Nilesh Javali <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]>
2020-08-17scsi: qla2xxx: Reduce noisy debug messageQuinn Tran1-2/+2
Update debug level and message for ELS IOCB done. Link: https://lore.kernel.org/r/[email protected] Reviewed-by: Himanshu Madhani <[email protected]> Signed-off-by: Quinn Tran <[email protected]> Signed-off-by: Nilesh Javali <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]>
2020-08-17scsi: qla2xxx: Fix login timeoutQuinn Tran2-4/+16
Multipath errors were seen during failback due to login timeout. The remote device sent LOGO, the local host tore down the session and did relogin. The RSCN arrived indicates remote device is going through failover after which the relogin is in a 20s timeout phase. At this point the driver is stuck in the relogin process. Add a fix to delete the session as part of abort/flush the login. Link: https://lore.kernel.org/r/[email protected] Reviewed-by: Himanshu Madhani <[email protected]> Signed-off-by: Quinn Tran <[email protected]> Signed-off-by: Nilesh Javali <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]>
2020-08-17scsi: qla2xxx: Indicate correct supported speeds for Mezz cardQuinn Tran1-5/+12
Correct the supported speeds for 16G Mezz card. Link: https://lore.kernel.org/r/[email protected] Reviewed-by: Himanshu Madhani <[email protected]> Signed-off-by: Quinn Tran <[email protected]> Signed-off-by: Nilesh Javali <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]>
2020-08-17scsi: qla2xxx: Flush I/O on zone disableQuinn Tran1-1/+0
Perform implicit logout to flush I/O on zone disable. Link: https://lore.kernel.org/r/[email protected] Reviewed-by: Himanshu Madhani <[email protected]> Signed-off-by: Quinn Tran <[email protected]> Signed-off-by: Himanshu Madhani <[email protected]> Signed-off-by: Nilesh Javali <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]>
2020-08-17scsi: qla2xxx: Flush all sessions on zone disableQuinn Tran1-0/+12
On Zone Disable, certain switches would ignore all commands. This causes timeout for both switch scan command and abort of that command. On detection of this condition, all sessions will be shutdown. Link: https://lore.kernel.org/r/[email protected] Reviewed-by: Himanshu Madhani <[email protected]> Signed-off-by: Quinn Tran <[email protected]> Signed-off-by: Himanshu Madhani <[email protected]> Signed-off-by: Nilesh Javali <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]>
2020-08-17scsi: qla2xxx: Use MBX_TOV_SECONDS for mailbox command timeout valuesEnzo Matsumiya1-7/+7
Improves readability of qla_mbx.c. Link: https://lore.kernel.org/r/[email protected] Reviewed-by: Himanshu Madhani <[email protected]> Reviewed-by: Roman Bolshakov <[email protected]> Signed-off-by: Enzo Matsumiya <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]>
2020-08-17scsi: scsi_debug: Fix scp is NULL errorsDouglas Gilbert1-0/+2
John Garry reported 'sdebug_q_cmd_complete: scp is NULL' failures that were mainly seen on aarch64 machines (e.g. RPi 4 with four A72 CPUs). The problem was tracked down to a missing critical section on a "short circuit" path. Namely, the time to process the current command so far has already exceeded the requested command duration (i.e. the number of nanoseconds in the ndelay parameter). The random=1 parameter setting was pivotal in finding this error. The failure scenario involved first taking that "short circuit" path (due to a very short command duration) and then taking the more likely hrtimer_start() path (due to a longer command duration). With random=1 each command's duration is taken from the uniformly distributed [0..ndelay) interval. The fio utility also helped by reliably generating the error scenario at about once per minute on a RPi 4 (64 bit OS). Link: https://lore.kernel.org/r/[email protected] Reported-by: John Garry <[email protected]> Reviewed-by: Lee Duncan <[email protected]> Signed-off-by: Douglas Gilbert <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]>
2020-08-17scsi: ufs: No need to send Abort Task if the task in DB was clearedBean Huo1-7/+8
If the bit corresponding to a task in the Doorbell register has been cleared, no need to poll the status of the task on the device side and to send an Abort Task TM. Instead, let it directly goto cleanup. In addition, to keep original debug output, move the goto below the debug print. Link: https://lore.kernel.org/r/[email protected] Reviewed-by: Stanley Chu <[email protected]> Reviewed-by: Can Guo <[email protected]> Signed-off-by: Bean Huo <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]>
2020-08-17scsi: ufs: Clean up completed request without interrupt notificationStanley Chu1-1/+2
If somehow no interrupt notification is raised for a completed request and its doorbell bit is cleared by host, UFS driver needs to cleanup its outstanding bit in ufshcd_abort(). Otherwise, system may behave abnormally in the following scenario: After ufshcd_abort() returns, this request will be requeued by SCSI layer with its outstanding bit set. Any future completed request will trigger ufshcd_transfer_req_compl() to handle all "completed outstanding bits". At this time the "abnormal outstanding bit" will be detected and the "requeued request" will be chosen to execute request post-processing flow. This is wrong because this request is still "alive". Link: https://lore.kernel.org/r/[email protected] Reviewed-by: Can Guo <[email protected]> Acked-by: Avri Altman <[email protected]> Signed-off-by: Stanley Chu <[email protected]> Signed-off-by: Bean Huo <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]>
2020-08-17scsi: ufs: Improve interrupt handling for shared interruptsAdrian Hunter1-3/+3
For shared interrupts, the interrupt status might be zero, so check that first. Link: https://lore.kernel.org/r/[email protected] Reviewed-by: Avri Altman <[email protected]> Signed-off-by: Adrian Hunter <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]>
2020-08-17scsi: ufs: Fix interrupt error message for shared interruptsAdrian Hunter1-1/+1
The interrupt might be shared, in which case it is not an error for the interrupt handler to be called when the interrupt status is zero, so don't print the message unless there was enabled interrupt status. Link: https://lore.kernel.org/r/[email protected] Fixes: 9333d7757348 ("scsi: ufs: Fix irq return code") Reviewed-by: Avri Altman <[email protected]> Signed-off-by: Adrian Hunter <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]>
2020-08-17scsi: ufs-pci: Add quirk for broken auto-hibernate for Intel EHLAdrian Hunter2-3/+22
Intel EHL UFS host controller advertises auto-hibernate capability but it does not work correctly. Add a quirk for that. [mkp: checkpatch fix] Link: https://lore.kernel.org/r/[email protected] Fixes: 8c09d7527697 ("scsi: ufshdc-pci: Add Intel PCI IDs for EHL") Acked-by: Stanley Chu <[email protected]> Signed-off-by: Adrian Hunter <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]>
2020-08-17scsi: ufs-mediatek: Fix incorrect time to wait link statusStanley Chu1-1/+1
Fix incorrect calculation of "ms" based waiting time in function ufs_mtk_setup_clocks(). Link: https://lore.kernel.org/r/[email protected] Fixes: 9006e3986f66 ("scsi: ufs-mediatek: Do not gate clocks if auto-hibern8 is not entered yet") Reviewed-by: Avri Altman <[email protected]> Signed-off-by: Stanley Chu <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]>
2020-08-17scsi: ufs: Fix possible infinite loop in ufshcd_holdStanley Chu1-1/+4
In ufshcd_suspend(), after clk-gating is suspended and link is set as Hibern8 state, ufshcd_hold() is still possibly invoked before ufshcd_suspend() returns. For example, MediaTek's suspend vops may issue UIC commands which would call ufshcd_hold() during the command issuing flow. Now if UFSHCD_CAP_HIBERN8_WITH_CLK_GATING capability is enabled, then ufshcd_hold() may enter infinite loops because there is no clk-ungating work scheduled or pending. In this case, ufshcd_hold() shall just bypass, and keep the link as Hibern8 state. Link: https://lore.kernel.org/r/[email protected] Reviewed-by: Avri Altman <[email protected]> Co-developed-by: Andy Teng <[email protected]> Signed-off-by: Andy Teng <[email protected]> Signed-off-by: Stanley Chu <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]>
2020-08-17scsi: ufs: ti-j721e-ufs: Fix error return in ti_j721e_ufs_probe()Jing Xiangfeng1-0/+1
Fix to return error code PTR_ERR() from the error handling case instead of 0. Link: https://lore.kernel.org/r/[email protected] Fixes: 22617e216331 ("scsi: ufs: ti-j721e-ufs: Fix unwinding of pm_runtime changes") Reviewed-by: Avri Altman <[email protected]> Signed-off-by: Jing Xiangfeng <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]>
2020-08-17scsi: ufs: Fix a race condition between error handler and runtime PM opsCan Guo1-34/+51
The current IRQ handler blocks SCSI requests before scheduling eh_work, when error handler calls pm_runtime_get_sync, if ufshcd_suspend/resume sends a SCSI cmd, most likely the SSU cmd, since SCSI requests are blocked, pm_runtime_get_sync() will never return because ufshcd_suspend/resume is blocked by the SCSI cmd. - In queuecommand path, hba->ufshcd_state check and ufshcd_send_command should stay under the same spin lock. This is to make sure that no more commands leak into doorbell after hba->ufshcd_state is changed. - Don't block SCSI requests before error handler starts to run, let error handler block SCSI requests when it is ready to start error recovery. - Don't let SCSI layer keep requeuing the SCSI cmds sent from HBA runtime PM ops, let them pass or fail them. Let them pass if eh_work is scheduled due to non-fatal errors. Fail them if eh_work is scheduled due to fatal errors, otherwise the cmds may eventually time out since UFS is in bad state, which gets error handler blocked for too long. If we fail the SCSI cmds sent from HBA runtime PM ops, HBA runtime PM ops fails too, but it does not hurt since error handler can recover HBA runtime PM error. Link: https://lore.kernel.org/r/[email protected] Reviewed-by: Bean Huo <[email protected]> Reviewed-by: Asutosh Das <[email protected]> Signed-off-by: Can Guo <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]>
2020-08-17scsi: ufs: Move dumps in IRQ handler to error handlerCan Guo1-8/+15
Performing dumps in the IRQ handler causes system stability issues. Move dumps to the error handler and only print basic host registers here. Link: https://lore.kernel.org/r/[email protected] Reviewed-by: Bean Huo <[email protected]> Reviewed-by: Asutosh Das <[email protected]> Signed-off-by: Can Guo <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]>
2020-08-17scsi: ufs: Recover HBA runtime PM error in error handlerCan Guo1-9/+99
The current error handler can not recover HBA runtime PM error if ufshcd_suspend/resume has failed due to UFS errors, e.g. hibern8 enter/exit error or SSU cmd error. When this happens, error handler may fail performing a full reset and restore because error handler always assumes that power, IRQs and clocks are ready after pm_runtime_get_sync returns, but actually they are not if ufshcd_resume fails[1]. If ufschd_suspend/resume fails due to UFS errors, runtime PM framework saves the error value to dev.power.runtime_error. After that, HBA dev runtime suspend/resume would not be invoked anymore unless runtime_error is cleared[2]. In case of ufshcd_suspend/resume fails due to UFS errors, for scenario [1], error handler cannot assume anything of pm_runtime_get_sync, meaning error handler should explicitly turn ON powers, IRQs and clocks again. To get the HBA runtime PM work as regard for scenario [2], error handler can clear the runtime_error by calling pm_runtime_set_active() if full reset and restore succeeds. And, more important, if pm_runtime_set_active() returns no error, which means runtime_error has been cleared, we also need to resume those scsi devices under HBA in case any of them has failed to be resumed due to HBA runtime resume failure. This is to unblock blk_queue_enter in case there are bios waiting inside it. Link: https://lore.kernel.org/r/[email protected] Reviewed-by: Bean Huo <[email protected]> Reviewed-by: Asutosh Das <[email protected]> Signed-off-by: Can Guo <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]>
2020-08-17scsi: ufs: Fix concurrency of error handler and other error recovery pathsCan Guo3-128/+150
Error recovery can be invoked from multiple code paths, including hibern8 enter/exit (from ufshcd_link_recovery), ufshcd_eh_host_reset_handler() and eh_work scheduled from IRQ context. Ultimately, these paths are all trying to invoke ufshcd_reset_and_restore() in either a synchronous or asynchronous manner. This causes problems: - If link recovery happens during ungate work, ufshcd_hold() would be called recursively. Although commit 53c12d0ef6fc ("scsi: ufs: fix error recovery after the hibern8 exit failure") fixed a deadlock due to recursive calls of ufshcd_hold() by adding a check of eh_in_progress into ufshcd_hold, this check allows eh_work to run in parallel while link recovery is running. - Similar concurrency can also happen when error recovery is invoked from ufshcd_eh_host_reset_handler and ufshcd_link_recovery. - Concurrency can even happen between eh_works. eh_work, currently queued on system_wq, is allowed to have multiple instances running in parallel, but we don't have proper protection for that. If any of above concurrency scenarios happen, error recovery would fail and lead ufs device and host into bad states. To fix the concurrency problem, this change queues eh_work on a single threaded workqueue and removes link recovery calls from the hibern8 enter/exit path. In addition, make use of eh_work in eh_host_reset_handler instead of calling ufshcd_reset_and_restore. This unifies the UFS error recovery mechanism. According to the UFSHCI JEDEC spec, hibern8 enter/exit error occurs when the link is broken. This essentially applies to any power mode change operations (since they all use PACP_PWR cmds in UniPro layer). So, if a power mode change operation (including AH8 enter/exit) fails, mark link state as UIC_LINK_BROKEN_STATE and schedule the eh_work. In this case, error handler needs to do a full reset and restore to recover the link back to active. Before the link state is recovered to active, ufshcd_uic_pwr_ctrl simply returns -ENOLINK to avoid more errors. Link: https://lore.kernel.org/r/[email protected] Reviewed-by: Bean Huo <[email protected]> Reviewed-by: Asutosh Das <[email protected]> Signed-off-by: Can Guo <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]>
2020-08-17scsi: ufs: Add some debug information to ufshcd_print_host_state()Can Guo2-13/+23
Information about the last interrupt status and timestamp is helpful when debugging system stability issues (IRQ starvation, for instance). Add this information to ufshcd_print_host_state() output. In addition, UFS device information such as model name and firmware version also comes in handy during debugging. This is printed as well. Link: https://lore.kernel.org/r/[email protected] Reviewed-by: Avri Altman <[email protected]> Reviewed-by: Hongwu Su <[email protected]> Reviewed-by: Asutosh Das <[email protected]> Reviewed-by: Stanley Chu <[email protected]> Reviewed-by: Bean Huo <[email protected]> Signed-off-by: Can Guo <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]>
2020-08-17scsi: ufs-qcom: Remove testbus dump in ufs_qcom_dump_dbg_regsCan Guo1-32/+0
Dumping testbus registers outputs a lot of information and can cause stability issues. Remove the dump code. Link: https://lore.kernel.org/r/[email protected] Reviewed-by: Hongwu Su <[email protected]> Reviewed-by: Avri Altman <[email protected]> Reviewed-by: Bean Huo <[email protected]> Reviewed-by: Asutosh Das <[email protected]> Signed-off-by: Can Guo <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]>
2020-08-17scsi: ufs: ufs-qcom: Fix race conditions caused by ufs_qcom_testbus_config()Can Guo1-5/+0
If ufs_qcom_dump_dbg_regs() calls ufs_qcom_testbus_config() from ufshcd_suspend/resume and/or clk gate/ungate context, pm_runtime_get_sync() and ufshcd_hold() will cause a race condition. Fix this by removing the unnecessary calls of pm_runtime_get_sync() and ufshcd_hold(). Link: https://lore.kernel.org/r/[email protected] Reviewed-by: Hongwu Su <[email protected]> Reviewed-by: Avri Altman <[email protected]> Reviewed-by: Bean Huo <[email protected]> Reviewed-by: Asutosh Das <[email protected]> Signed-off-by: Can Guo <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]>
2020-08-17scsi: ufs: Add checks before setting clk-gating statesCan Guo1-3/+14
Clock gating can be turned on/off selectively which means the associated state information is only correct if the feature is enabled. This change makes sure that we only look at state of clk-gating if it is enabled. Link: https://lore.kernel.org/r/[email protected] Reviewed-by: Avri Altman <[email protected]> Reviewed-by: Hongwu Su <[email protected]> Reviewed-by: Stanley Chu <[email protected]> Reviewed-by: Bean Huo <[email protected]> Reviewed-by: Asutosh Das <[email protected]> Signed-off-by: Can Guo <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]>
2020-08-14Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsiLinus Torvalds15-94/+163
Pull more SCSI updates from James Bottomley: "This is the set of patches which arrived too late to stabilise in -next for the first pull. It's really just an lpfc driver update and an assortment of minor fixes, all in drivers. The only core update is to the zone block device driver, which isn't the one most people use" * tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: scsi: lpfc: Update lpfc version to 12.8.0.3 scsi: lpfc: Fix LUN loss after cable pull scsi: lpfc: Fix validation of bsg reply lengths scsi: lpfc: Fix retry of PRLI when status indicates its unsupported scsi: lpfc: Fix oops when unloading driver while running mds diags scsi: lpfc: Fix RSCN timeout due to incorrect gidft counter scsi: lpfc: Fix no message shown for lpfc_hdw_queue out of range value scsi: lpfc: Fix FCoE speed reporting scsi: lpfc: Add missing misc_deregister() for lpfc_init() scsi: lpfc: nvmet: Avoid hang / use-after-free again when destroying targetport scsi: scsi_transport_sas: Add spaces around binary operator "|" scsi: sd_zbc: Improve zone revalidation scsi: libfc: Free skb in fc_disc_gpn_id_resp() for valid cases scsi: fcoe: Memory leak fix in fcoe_sysfs_fcf_del() scsi: target: Make iscsit_register_transport() return void
2020-08-11Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhostLinus Torvalds1-2/+2
Pull virtio updates from Michael Tsirkin: - IRQ bypass support for vdpa and IFC - MLX5 vdpa driver - Endianness fixes for virtio drivers - Misc other fixes * tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (71 commits) vdpa/mlx5: fix up endian-ness for mtu vdpa: Fix pointer math bug in vdpasim_get_config() vdpa/mlx5: Fix pointer math in mlx5_vdpa_get_config() vdpa/mlx5: fix memory allocation failure checks vdpa/mlx5: Fix uninitialised variable in core/mr.c vdpa_sim: init iommu lock virtio_config: fix up warnings on parisc vdpa/mlx5: Add VDPA driver for supported mlx5 devices vdpa/mlx5: Add shared memory registration code vdpa/mlx5: Add support library for mlx5 VDPA implementation vdpa/mlx5: Add hardware descriptive header file vdpa: Modify get_vq_state() to return error code net/vdpa: Use struct for set/get vq state vdpa: remove hard coded virtq num vdpasim: support batch updating vhost-vdpa: support IOTLB batching hints vhost-vdpa: support get/set backend features vhost: generialize backend features setting/getting vhost-vdpa: refine ioctl pre-processing vDPA: dont change vq irq after DRIVER_OK ...
2020-08-07Merge tag 'pci-v5.9-changes' of ↵Linus Torvalds3-3/+7
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci Pull PCI updates from Bjorn Helgaas: "Enumeration: - Fix pci_cfg_wait queue locking problem (Bjorn Helgaas) - Convert PCIe capability PCIBIOS errors to errno (Bolarinwa Olayemi Saheed) - Align PCIe capability and PCI accessor return values (Bolarinwa Olayemi Saheed) - Fix pci_create_slot() reference count leak (Qiushi Wu) - Announce device after early fixups (Tiezhu Yang) PCI device hotplug: - Make rpadlpar functions static (Wei Yongjun) Driver binding: - Add device even if driver attach failed (Rajat Jain) Virtualization: - xen: Remove redundant initialization of irq (Colin Ian King) IOMMU: - Add pci_pri_supported() to check device or associated PF (Ashok Raj) - Release IVRS table in AMD ACS quirk (Hanjun Guo) - Mark AMD Navi10 GPU rev 0x00 ATS as broken (Kai-Heng Feng) - Treat "external-facing" devices themselves as internal (Rajat Jain) MSI: - Forward MSI-X error code in pci_alloc_irq_vectors_affinity() (Piotr Stankiewicz) Error handling: - Clear PCIe Device Status errors only if OS owns AER (Jonathan Cameron) - Log correctable errors as warning, not error (Matt Jolly) - Use 'pci_channel_state_t' instead of 'enum pci_channel_state' (Luc Van Oostenryck) Peer-to-peer DMA: - Allow P2PDMA on AMD Zen and newer CPUs (Logan Gunthorpe) ASPM: - Add missing newline in sysfs 'policy' (Xiongfeng Wang) Native PCIe controllers: - Convert to devm_platform_ioremap_resource_byname() (Dejin Zheng) - Convert to devm_platform_ioremap_resource() (Dejin Zheng) - Remove duplicate error message from devm_pci_remap_cfg_resource() callers (Dejin Zheng) - Fix runtime PM imbalance on error (Dinghao Liu) - Remove dev_err() when handing an error from platform_get_irq() (Krzysztof Wilczyński) - Use pci_host_bridge.windows list directly instead of splicing in a temporary list for cadence, mvebu, host-common (Rob Herring) - Use pci_host_probe() instead of open-coding all the pieces for altera, brcmstb, iproc, mobiveil, rcar, rockchip, tegra, v3, versatile, xgene, xilinx, xilinx-nwl (Rob Herring) - Default host bridge parent device to the platform device (Rob Herring) - Use pci_is_root_bus() instead of tracking root bus number separately in aardvark, designware (imx6, keystone, designware-host), mobiveil, xilinx-nwl, xilinx, rockchip, rcar (Rob Herring) - Set host bridge bus number in pci_scan_root_bus_bridge() instead of each driver for aardvark, designware-host, host-common, mediatek, rcar, tegra, v3-semi (Rob Herring) - Move DT resource setup into devm_pci_alloc_host_bridge() (Rob Herring) - Set bridge map_irq and swizzle_irq to default functions; drivers that don't support legacy IRQs (iproc) need to undo this (Rob Herring) ARM Versatile PCIe controller driver: - Drop flag PCI_ENABLE_PROC_DOMAINS (Rob Herring) Cadence PCIe controller driver: - Use "dma-ranges" instead of "cdns,no-bar-match-nbits" property (Kishon Vijay Abraham I) - Remove "mem" from reg binding (Kishon Vijay Abraham I) - Fix cdns_pcie_{host|ep}_setup() error path (Kishon Vijay Abraham I) - Convert all r/w accessors to perform only 32-bit accesses (Kishon Vijay Abraham I) - Add support to start link and verify link status (Kishon Vijay Abraham I) - Allow pci_host_bridge to have custom pci_ops (Kishon Vijay Abraham I) - Add new *ops* for CPU addr fixup (Kishon Vijay Abraham I) - Fix updating Vendor ID and Subsystem Vendor ID register (Kishon Vijay Abraham I) - Use bridge resources for outbound window setup (Rob Herring) - Remove private bus number and range storage (Rob Herring) Cadence PCIe endpoint driver: - Add MSI-X support (Alan Douglas) HiSilicon PCIe controller driver: - Remove non-ECAM HiSilicon hip05/hip06 driver (Rob Herring) Intel VMD host bridge driver: - Use Shadow MEMBAR registers for QEMU/KVM guests (Jon Derrick) Loongson PCIe controller driver: - Use DECLARE_PCI_FIXUP_EARLY for bridge_class_quirk() (Tiezhu Yang) Marvell Aardvark PCIe controller driver: - Indicate error in 'val' when config read fails (Pali Rohár) - Don't touch PCIe registers if no card connected (Pali Rohár) Marvell MVEBU PCIe controller driver: - Setup BAR0 in order to fix MSI (Shmuel Hazan) Microsoft Hyper-V host bridge driver: - Fix a timing issue which causes kdump to fail occasionally (Wei Hu) - Make some functions static (Wei Yongjun) NVIDIA Tegra PCIe controller driver: - Revert tegra124 raw_violation_fixup (Nicolas Chauvet) - Remove PLL power supplies (Thierry Reding) Qualcomm PCIe controller driver: - Change duplicate PCI reset to phy reset (Abhishek Sahu) - Add missing ipq806x clocks in PCIe driver (Ansuel Smith) - Add missing reset for ipq806x (Ansuel Smith) - Add ext reset (Ansuel Smith) - Use bulk clk API and assert on error (Ansuel Smith) - Add support for tx term offset for rev 2.1.0 (Ansuel Smith) - Define some PARF params needed for ipq8064 SoC (Ansuel Smith) - Add ipq8064 rev2 variant (Ansuel Smith) - Support PCI speed set for ipq806x (Sham Muthayyan) Renesas R-Car PCIe controller driver: - Use devm_pci_alloc_host_bridge() (Rob Herring) - Use struct pci_host_bridge.windows list directly (Rob Herring) - Convert rcar-gen2 to use modern host bridge probe functions (Rob Herring) TI J721E PCIe driver: - Add TI J721E PCIe host and endpoint driver (Kishon Vijay Abraham I) Xilinx Versal CPM PCIe controller driver: - Add Versal CPM Root Port driver and YAML schema (Bharat Kumar Gogada) MicroSemi Switchtec management driver: - Add missing __iomem and __user tags to fix sparse warnings (Logan Gunthorpe) Miscellaneous: - Replace http:// links with https:// (Alexander A. Klimov) - Replace lkml.org, spinics, gmane with lore.kernel.org (Bjorn Helgaas) - Remove unused pci_lost_interrupt() (Heiner Kallweit) - Move PCI_VENDOR_ID_REDHAT definition to pci_ids.h (Huacai Chen) - Fix kerneldoc warnings (Krzysztof Kozlowski)" * tag 'pci-v5.9-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (113 commits) PCI: Fix kerneldoc warnings PCI: xilinx-cpm: Add Versal CPM Root Port driver PCI: xilinx-cpm: Add YAML schemas for Versal CPM Root Port PCI: Set bridge map_irq and swizzle_irq to default functions PCI: Move DT resource setup into devm_pci_alloc_host_bridge() PCI: rcar-gen2: Convert to use modern host bridge probe functions PCI: Remove dev_err() when handing an error from platform_get_irq() MAINTAINERS: Add Kishon Vijay Abraham I for TI J721E SoC PCIe misc: pci_endpoint_test: Add J721E in pci_device_id table PCI: j721e: Add TI J721E PCIe driver PCI: switchtec: Add missing __iomem tag to fix sparse warnings PCI: switchtec: Add missing __iomem and __user tags to fix sparse warnings PCI: rpadlpar: Make functions static PCI/P2PDMA: Allow P2PDMA on AMD Zen and newer CPUs PCI: Release IVRS table in AMD ACS quirk PCI: Announce device after early fixups PCI: Mark AMD Navi10 GPU rev 0x00 ATS as broken PCI: Remove unused pci_lost_interrupt() dt-bindings: PCI: Add EP mode dt-bindings for TI's J721E SoC dt-bindings: PCI: Add host mode dt-bindings for TI's J721E SoC ...
2020-08-06Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsiLinus Torvalds189-3145/+6899
Pull SCSI updates from James Bottomley: "This consists of the usual driver updates (ufs, qla2xxx, tcmu, lpfc, hpsa, zfcp, scsi_debug) and minor bug fixes. We also have a huge docbook fix update like most other subsystems and no major update to the core (the few non trivial updates are either minor fixes or removing an unused feature [scsi_sdb_cache])" * tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (307 commits) scsi: scsi_transport_srp: Sanitize scsi_target_block/unblock sequences scsi: ufs-mediatek: Apply DELAY_AFTER_LPM quirk to Micron devices scsi: ufs: Introduce device quirk "DELAY_AFTER_LPM" scsi: virtio-scsi: Correctly handle the case where all LUNs are unplugged scsi: scsi_debug: Implement tur_ms_to_ready parameter scsi: scsi_debug: Fix request sense scsi: lpfc: Fix typo in comment for ULP scsi: ufs-mediatek: Prevent LPM operation on undeclared VCC scsi: iscsi: Do not put host in iscsi_set_flashnode_param() scsi: hpsa: Correct ctrl queue depth scsi: target: tcmu: Make TMR notification optional scsi: target: tcmu: Implement tmr_notify callback scsi: target: tcmu: Fix and simplify timeout handling scsi: target: tcmu: Factor out new helper ring_insert_padding scsi: target: tcmu: Do not queue aborted commands scsi: target: tcmu: Use priv pointer in se_cmd scsi: target: Add tmr_notify backend function scsi: target: Modify core_tmr_abort_task() scsi: target: iscsi: Fix inconsistent debug message scsi: target: iscsi: Fix login error when receiving ...
2020-08-06Merge tag 'hyperv-next-signed' of ↵Linus Torvalds1-5/+11
git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux Pull hyperv updates from Wei Liu: - A patch series from Andrea to improve vmbus code - Two clean-up patches from Alexander and Randy * tag 'hyperv-next-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux: hyperv: hyperv.h: drop a duplicated word tools: hv: change http to https in hv_kvp_daemon.c Drivers: hv: vmbus: Remove the lock field from the vmbus_channel struct scsi: storvsc: Introduce the per-storvsc_device spinlock Drivers: hv: vmbus: Remove unnecessary channel->lock critical sections (sc_list updaters) Drivers: hv: vmbus: Use channel_mutex in channel_vp_mapping_show() Drivers: hv: vmbus: Remove unnecessary channel->lock critical sections (sc_list readers) Drivers: hv: vmbus: Replace cpumask_test_cpu(, cpu_online_mask) with cpu_online() Drivers: hv: vmbus: Remove the numa_node field from the vmbus_channel struct Drivers: hv: vmbus: Remove the target_vp field from the vmbus_channel struct
2020-08-05Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-nextLinus Torvalds1-28/+50
Pull networking updates from David Miller: 1) Support 6Ghz band in ath11k driver, from Rajkumar Manoharan. 2) Support UDP segmentation in code TSO code, from Eric Dumazet. 3) Allow flashing different flash images in cxgb4 driver, from Vishal Kulkarni. 4) Add drop frames counter and flow status to tc flower offloading, from Po Liu. 5) Support n-tuple filters in cxgb4, from Vishal Kulkarni. 6) Various new indirect call avoidance, from Eric Dumazet and Brian Vazquez. 7) Fix BPF verifier failures on 32-bit pointer arithmetic, from Yonghong Song. 8) Support querying and setting hardware address of a port function via devlink, use this in mlx5, from Parav Pandit. 9) Support hw ipsec offload on bonding slaves, from Jarod Wilson. 10) Switch qca8k driver over to phylink, from Jonathan McDowell. 11) In bpftool, show list of processes holding BPF FD references to maps, programs, links, and btf objects. From Andrii Nakryiko. 12) Several conversions over to generic power management, from Vaibhav Gupta. 13) Add support for SO_KEEPALIVE et al. to bpf_setsockopt(), from Dmitry Yakunin. 14) Various https url conversions, from Alexander A. Klimov. 15) Timestamping and PHC support for mscc PHY driver, from Antoine Tenart. 16) Support bpf iterating over tcp and udp sockets, from Yonghong Song. 17) Support 5GBASE-T i40e NICs, from Aleksandr Loktionov. 18) Add kTLS RX HW offload support to mlx5e, from Tariq Toukan. 19) Fix the ->ndo_start_xmit() return type to be netdev_tx_t in several drivers. From Luc Van Oostenryck. 20) XDP support for xen-netfront, from Denis Kirjanov. 21) Support receive buffer autotuning in MPTCP, from Florian Westphal. 22) Support EF100 chip in sfc driver, from Edward Cree. 23) Add XDP support to mvpp2 driver, from Matteo Croce. 24) Support MPTCP in sock_diag, from Paolo Abeni. 25) Commonize UDP tunnel offloading code by creating udp_tunnel_nic infrastructure, from Jakub Kicinski. 26) Several pci_ --> dma_ API conversions, from Christophe JAILLET. 27) Add FLOW_ACTION_POLICE support to mlxsw, from Ido Schimmel. 28) Add SK_LOOKUP bpf program type, from Jakub Sitnicki. 29) Refactor a lot of networking socket option handling code in order to avoid set_fs() calls, from Christoph Hellwig. 30) Add rfc4884 support to icmp code, from Willem de Bruijn. 31) Support TBF offload in dpaa2-eth driver, from Ioana Ciornei. 32) Support XDP_REDIRECT in qede driver, from Alexander Lobakin. 33) Support PCI relaxed ordering in mlx5 driver, from Aya Levin. 34) Support TCP syncookies in MPTCP, from Flowian Westphal. 35) Fix several tricky cases of PMTU handling wrt. briding, from Stefano Brivio. * git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2056 commits) net: thunderx: initialize VF's mailbox mutex before first usage usb: hso: remove bogus check for EINPROGRESS usb: hso: no complaint about kmalloc failure hso: fix bailout in error case of probe ip_tunnel_core: Fix build for archs without _HAVE_ARCH_IPV6_CSUM selftests/net: relax cpu affinity requirement in msg_zerocopy test mptcp: be careful on subflow creation selftests: rtnetlink: make kci_test_encap() return sub-test result selftests: rtnetlink: correct the final return value for the test net: dsa: sja1105: use detected device id instead of DT one on mismatch tipc: set ub->ifindex for local ipv6 address ipv6: add ipv6_dev_find() net: openvswitch: silence suspicious RCU usage warning Revert "vxlan: fix tos value before xmit" ptp: only allow phase values lower than 1 period farsync: switch from 'pci_' to 'dma_' API wan: wanxl: switch from 'pci_' to 'dma_' API hv_netvsc: do not use VF device if link is down dpaa2-eth: Fix passing zero to 'PTR_ERR' warning net: macb: Properly handle phylink on at91sam9x ...
2020-08-05Merge branch 'pci/misc'Bjorn Helgaas1-1/+5
- Convert PCIe capability PCIBIOS errors to errno (Bolarinwa Olayemi Saheed) - Align PCIe capability and PCI accessor return values (Bolarinwa Olayemi Saheed) - Replace http:// links with https:// (Alexander A. Klimov) - Replace lkml.org, spinics, gmane with lore.kernel.org (Bjorn Helgaas) - Update panic message to mention kzalloc(), not kmalloc() (Liao Pingfang) - Move PCI_VENDOR_ID_REDHAT definition to pci_ids.h (Huacai Chen) - Remove unused pci_lost_interrupt() (Heiner Kallweit) * pci/misc: PCI: Remove unused pci_lost_interrupt() PCI: Move PCI_VENDOR_ID_REDHAT definition to pci_ids.h PCI: Fix error in panic message PCI: Replace lkml.org, spinics, gmane with lore.kernel.org PCI: Replace http:// links with https:// PCI: Align PCIe capability and PCI accessor return values PCI: Convert PCIe capability PCIBIOS errors to errno
2020-08-05Merge tag 'for-5.9/drivers-20200803' of git://git.kernel.dk/linux-blockLinus Torvalds1-0/+6
Pull block driver updates from Jens Axboe: - NVMe: - ZNS support (Aravind, Keith, Matias, Niklas) - Misc cleanups, optimizations, fixes (Baolin, Chaitanya, David, Dongli, Max, Sagi) - null_blk zone capacity support (Aravind) - MD: - raid5/6 fixes (ChangSyun) - Warning fixes (Damien) - raid5 stripe fixes (Guoqing, Song, Yufen) - sysfs deadlock fix (Junxiao) - raid10 deadlock fix (Vitaly) - struct_size conversions (Gustavo) - Set of bcache updates/fixes (Coly) * tag 'for-5.9/drivers-20200803' of git://git.kernel.dk/linux-block: (117 commits) md/raid5: Allow degraded raid6 to do rmw md/raid5: Fix Force reconstruct-write io stuck in degraded raid5 raid5: don't duplicate code for different paths in handle_stripe raid5-cache: hold spinlock instead of mutex in r5c_journal_mode_show md: print errno in super_written md/raid5: remove the redundant setting of STRIPE_HANDLE md: register new md sysfs file 'uuid' read-only md: fix max sectors calculation for super 1.0 nvme-loop: remove extra variable in create ctrl nvme-loop: set ctrl state connecting after init nvme-multipath: do not fall back to __nvme_find_path() for non-optimized paths nvme-multipath: fix logic for non-optimized paths nvme-rdma: fix controller reset hang during traffic nvme-tcp: fix controller reset hang during traffic nvmet: introduce the passthru Kconfig option nvmet: introduce the passthru configfs interface nvmet: Add passthru enable/disable helpers nvmet: add passthru code to process commands nvme: export nvme_find_get_ns() and nvme_put_ns() nvme: introduce nvme_ctrl_get_by_path() ...
2020-08-05virtio_scsi: correct tags for config space fieldsMichael S. Tsirkin1-2/+2
Tag config space fields as having virtio endian-ness. Signed-off-by: Michael S. Tsirkin <[email protected]> Reviewed-by: Cornelia Huck <[email protected]>
2020-08-04scsi: lpfc: Update lpfc version to 12.8.0.3Dick Kennedy1-1/+1
Update lpfc version to 12.8.0.3 Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Dick Kennedy <[email protected]> Signed-off-by: James Smart <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]>
2020-08-04scsi: lpfc: Fix LUN loss after cable pullDick Kennedy1-1/+7
On devices that support FCP sequence error recovery, which attempts to preserve the devices login across link bounce, adisc is used for device validation. Turns out the device fc4 type is cleared as part of the link bounce, but the ADISC handling doesn't restore the FC4 support as it normally would with a PRLI. This caused situations where the device wasn't reregistered with the transport thus scan logic and LUN discovery never kicked in. In the ADISC completion handling, reset the fc4 type so that transport port reregistration occurs with the remote port. Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Dick Kennedy <[email protected]> Signed-off-by: James Smart <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]>
2020-08-04scsi: lpfc: Fix validation of bsg reply lengthsDick Kennedy1-13/+8
There are a couple of code areas which validate sufficient reply buffer length, but the checks are using the request elements rather than the reply elements. Rework to validate using the reply structures. Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Dick Kennedy <[email protected]> Signed-off-by: James Smart <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]>
2020-08-04scsi: lpfc: Fix retry of PRLI when status indicates its unsupportedDick Kennedy1-3/+7
With port bounce/address swaps and timing between initiator GID queries vs remote port FC4 support registrations, the driver may be in a situation where it sends PRLIs for both FCP and NVME even though the target may not support one of the protocols. In this case, the remote port will reject the PRLI and usually indicate it does not support the request. However, the driver currently ignores the status of the failure and immediately retries the PRLI, which is pointless. In the case of this one remote port, the reception of the PRLI retry caused it to decide to send a LOGO. The LOGO restarted the process and the same results happened. It made the remote port undiscoverable to either protocol. Add logic to detect the non-support status and not attempt the retry of the PRLI. Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Dick Kennedy <[email protected]> Signed-off-by: James Smart <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]>
2020-08-04scsi: lpfc: Fix oops when unloading driver while running mds diagsDick Kennedy1-2/+9
While mds diagnostic tests are running, if the driver is requested to be unloaded, oops or hangs are observed. The driver doesn't terminate the processing of diag frames when the unload is started. As such: oops may be seen for __lpfc_sli_release_iocbq_s4 because ring memory is referenced that was already freed; or hangs see in lpfc_nvme_wait_for_io_drain as ios no longer complete. If unloading, don't process diag frames. Just clean them up. Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Dick Kennedy <[email protected]> Signed-off-by: James Smart <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]>
2020-08-04scsi: lpfc: Fix RSCN timeout due to incorrect gidft counterDick Kennedy1-6/+16
In configs with a large number of initiators in the same zone (>250), RSCN timeouts are seen when creating or deleting vports: lpfc 0000:07:00.1: 5:(0):0231 RSCN timeout Data: x0 x3 During RSCN processing driver issues GID_FT command to nameserver. A counter for number of simultaneous GID_FT commands is maintained (an unsigned value). The counter is incremented when the GID_FT is issued. If the GID_FT command fails for some reason the driver retries the GID_FT from the completion call back. But the counter was decremented before the retry was issued. When the second GID_FT completes, the callback again tries to decrement the counter, possibly wrapping to a very large non-zero value, which causes the RSCN cleanup code to not execute. Thus the RSCN timeout failure. Do not decrement the counter on a retry. Also add defensive checks to ensure the counter is not decremented if already zero. Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Dick Kennedy <[email protected]> Signed-off-by: James Smart <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]>
Powered by cgit, Gruvboxed by Blaster4385.