| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The COMMONONN bit turns off the PHY when the host controller puts it
into suspend state. This can happen during the following...
- Nothing is connected to the port
- The host controller goes into low power mode whatever due to auto
suspend or system suspend.
With COMMONONN we also must unset U2_FREECLK_EXISTS since the UTMI
clock is fed by the PHY.
With these changes we see a power savings of ~12mW when port is in
suspend.
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Justin Chen <justin.chen@broadcom.com>
Link: https://lore.kernel.org/r/1686859578-45242-2-git-send-email-justin.chen@broadcom.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
We should be disabling clocks when wake from USB is not needed. Since
this wasn't done, we had a clock imbalance since clocks were always
being enabled on resume.
Fixes: ae532b2b7aa5 ("phy: usb: Add "wake on" functionality for newer Synopsis XHCI controllers")
Fixes: b0c0b66c0b43 ("phy: usb: Add support for wake and USB low power mode for 7211 S2/S5")
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/1665005418-15807-7-git-send-email-justinpopo6@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Split port modes into two different variables. Supported port modes
is what the hardware supports. While port mode is how the hardware
is currently configured and can be dynamically changed through the
sysfs. We initialize all supported port modes on init even though
the port mode may not be selected because we cannot guarantee the
downstream interface from the phy will be active or not.
This also fixes an issue where port modes selected via sysfs were
not being saved through suspend/resume.
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/1665005418-15807-2-git-send-email-justinpopo6@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Just like every other family BCM4908 should get its own enum value. That
is required to properly handle it in chipset conditional code.
The real change is excluding BCM4908 from the PLL reprogramming code
(see brcmusb_usb3_pll_54mhz()). I'm not sure what's the BCM4908
reference clock frequency but:
1. BCM4908 custom driver from Broadcom's SDK doesn't reprogram PLL
2. Doing that in Linux driver stopped PHY handling some USB 3.0 devices
This change makes USB 3.0 PHY recognize e.g.:
1. 04e8:6860 - Samsung Electronics Co., Ltd Galaxy series, misc. (MTP mode)
2. 1058:259f - Western Digital My Passport 259F
Broadcom's STB SoCs come with a set of SUN_TOP_CTRL_* registers that
allow reading chip family and product ids. Such a block & register is
missing on BCM4908 so this commit introduces "compatible" string
specific binding.
Fixes: 4b402fa8e0b7 ("phy: phy-brcm-usb: support PHY on the BCM4908")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220218172459.10431-1-zajec5@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
While IS_ENABLED() is perfectly fine for CONFIG_* symbols, it is not
for other symbols such as __BIG_ENDIAN that is provided directly by
the compiler.
Switch to use CONFIG_CPU_BIG_ENDIAN instead of __BIG_ENDIAN.
Signed-off-by: Chen Li <chenli@uniontech.com>
Reviewed-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Fixes: 94583a41047e ("phy: usb: Restructure in preparation for adding 7216 USB support")
Link: https://lore.kernel.org/r/87czuggpra.wl-chenli@uniontech.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Add support for 7211 USB wake. Disable all possible 7211 USB logic
for S2/S5 if USB wake is not enabled.
On the 7211, the XHCI wake signal was not connected properly and
only goes to the USB1_USB1_CTRL_TP_DIAG1 diagonstic register.
The workaround is to have VPU code running that polls for the
proper bit in the DIAG register and to wake the system when
the bit is asserted.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
The BDC "Read Transaction Size" needs to be changed from 1024
bytes to 256 bytes to prevent occasional transaction failures.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
The 7211b0 has added the STB XHCI Synopsys controller and it
will be used instead of the RPi based DWC USB controller. The new
Synopsys XHCI controller core is the same one that is used on the
7216, but because of the way the STB USB PHY is used on both the A0
and B0, some of the PHY control is different.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
The 7216 has the new USB XHCI controller from Synopsys. While
this new controller and the PHY are similar to the STB versions,
the major differences are:
- Many of the registers and fields in the CTRL block have been
removed or changed.
- A new set of Synopsys control registers, BCHP_USB_XHCI_GBL, were
added.
- MDIO functionality has been replaced with direct access registers
in the BCHP_USB_XHCI_GBL block.
- Power up PHY defaults that had to be changed by MDIO in previous
chips will now power up with the correct defaults.
A new init module was created for this new Synopsys USB controller.
A new compatible string was added and the driver will dispatch
into one of two init modules based on it. A "reg-names" field was
added so the driver can more easily get optional registers.
A DT bindings document was also added for this driver.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
The driver is being restructured in preparation for adding support
for the new Synopsys USB conroller on the 7216. Since all the bugs
and work-arounds in previous STB chips are supposed to be fixed,
most of the code in phy-brcm-usb-init.c is not needed. Instead of
adding more complexity to the already complicated phy-brcm-usb-init.c
module, the driver will be restructured to use a vector table to
dispatch into different C modules for the different controllers.
There was also some general cleanup done including some ipp setup
code that was incorrect.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Add the ability to handle USB wake events from USB devices when
in S2 mode. Typically there is some additional configuration
needed to tell the USB device to generate the wake event when
suspended but this varies with the different USB device classes.
For example, on USB Ethernet dongles, ethtool should be used to
enable the magic packet wake functionality in the dongle.
NOTE: This requires that the "power/wakeup" sysfs entry for
the USB device generating the wakeup be set to "enabled".
This functionality requires a special hardware sideband path that
will trigger the AON_PM_L2 interrupt needed to wake the system from
S2 even though the USB host controllers are in IDDQ (low power state)
and most USB related clocks are shut off. For the sideband signaling
to work we need to leave the usbx_freerun clock running, but this
clock consumes very little power by design. There's a bug in the
XHCI wake hardware so only EHCI/OHCI wake is currently supported.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Based on 1 normalized pattern(s):
this software is licensed under the terms of the gnu general public
license version 2 as published by the free software foundation and
may be copied distributed and modified under those terms this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 285 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.642774971@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add a new USB Phy driver for Broadcom STB SoCs. This driver
supports Broadcom STB ARM SoCs. This driver in
combination with the Broadcom STB ohci, ehci and xhci
drivers will enable USB1.1, USB2.0 and USB3.0 support.
This Phy driver also supports the Broadcom BDC gadget
driver.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|