| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Currently, dw_pcie_msi_init() allocates and maps page for msi, then
program the PCIE_MSI_ADDR_LO and PCIE_MSI_ADDR_HI. The Root Complex
may lose power during suspend-to-RAM, so when we resume, we want to
redo the latter but not the former. If designware based driver (for
example, pcie-tegra194.c) calls dw_pcie_msi_init() in resume path, the
msi page will be leaked.
As pointed out by Rob and Ard, there's no need to allocate a page for
the MSI address, we could use an address in the driver data.
To avoid map the MSI msg again during resume, we move the map MSI msg
from dw_pcie_msi_init() to dw_pcie_host_init().
Suggested-by: Rob Herring <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jisheng Zhang <[email protected]>
Signed-off-by: Lorenzo Pieralisi <[email protected]>
Reviewed-by: Rob Herring <[email protected]>
|
|
If MSI is disabled, there's no need to program PCIE_MSI_INTR0_MASK
and PCIE_MSI_INTR0_ENABLE registers.
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jisheng Zhang <[email protected]>
Signed-off-by: Lorenzo Pieralisi <[email protected]>
Reviewed-by: Rob Herring <[email protected]>
Acked-by: Gustavo Pimentel <[email protected]>
|
|
After applying "PCI: dwc: Add common iATU register support",
there is no need to set own iATU in the Keystone driver itself.
Suggested-by: Rob Herring <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Kunihiko Hayashi <[email protected]>
Signed-off-by: Lorenzo Pieralisi <[email protected]>
Reviewed-by: Rob Herring <[email protected]>
Cc: Murali Karicheri <[email protected]>
Cc: Jingoo Han <[email protected]>
Cc: Gustavo Pimentel <[email protected]>
|
|
This gets iATU register area from reg property that has reg-names "atu".
In Synopsys DWC version 4.80 or later, since iATU register area is
separated from core register area, this area is necessary to get from
DT independently.
Suggested-by: Rob Herring <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Kunihiko Hayashi <[email protected]>
Signed-off-by: Lorenzo Pieralisi <[email protected]>
Reviewed-by: Rob Herring <[email protected]>
Cc: Murali Karicheri <[email protected]>
Cc: Jingoo Han <[email protected]>
Cc: Gustavo Pimentel <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 irq updates from Thomas Gleixner:
"Surgery of the MSI interrupt handling to prepare the support of
upcoming devices which require non-PCI based MSI handling:
- Cleanup historical leftovers all over the place
- Rework the code to utilize more core functionality
- Wrap XEN PCI/MSI interrupts into an irqdomain to make irqdomain
assignment to PCI devices possible.
- Assign irqdomains to PCI devices at initialization time which
allows to utilize the full functionality of hierarchical
irqdomains.
- Remove arch_.*_msi_irq() functions from X86 and utilize the
irqdomain which is assigned to the device for interrupt management.
- Make the arch_.*_msi_irq() support conditional on a config switch
and let the last few users select it"
* tag 'x86-irq-2020-10-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (40 commits)
PCI: MSI: Fix Kconfig dependencies for PCI_MSI_ARCH_FALLBACKS
x86/apic/msi: Unbreak DMAR and HPET MSI
iommu/amd: Remove domain search for PCI/MSI
iommu/vt-d: Remove domain search for PCI/MSI[X]
x86/irq: Make most MSI ops XEN private
x86/irq: Cleanup the arch_*_msi_irqs() leftovers
PCI/MSI: Make arch_.*_msi_irq[s] fallbacks selectable
x86/pci: Set default irq domain in pcibios_add_device()
iommm/amd: Store irq domain in struct device
iommm/vt-d: Store irq domain in struct device
x86/xen: Wrap XEN MSI management into irqdomain
irqdomain/msi: Allow to override msi_domain_alloc/free_irqs()
x86/xen: Consolidate XEN-MSI init
x86/xen: Rework MSI teardown
x86/xen: Make xen_msi_init() static and rename it to xen_hvm_msi_init()
PCI/MSI: Provide pci_dev_has_special_msi_domain() helper
PCI_vmd_Mark_VMD_irqdomain_with_DOMAIN_BUS_VMD_MSI
irqdomain/msi: Provide DOMAIN_BUS_VMD_MSI
x86/irq: Initialize PCI/MSI domain at PCI init time
x86/pci: Reducde #ifdeffery in PCI init code
...
|
|
Fix sparse build warning:
drivers/pci/controller/pcie-iproc-platform.c:102:33: warning: Using plain integer as NULL pointer
The map_irq member of the struct iproc_pcie takes a function pointer
serving as a callback to map interrupts, therefore we should pass a NULL
pointer to it rather than a integer in the iproc_pcie_pltfm_probe()
function.
Related:
commit b64aa11eb2dd ("PCI: Set bridge map_irq and swizzle_irq to
default functions")
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Krzysztof Wilczyński <[email protected]>
Signed-off-by: Lorenzo Pieralisi <[email protected]>
Reviewed-by: Rob Herring <[email protected]>
|
|
Recent laptops with dual AMD GPUs fail to suspend the discrete GPU, thus
causing lockups on system sleep and high power consumption at runtime.
The discrete GPU would normally be suspended to D3cold by turning off
ACPI _PR3 Power Resources of the Root Port above the GPU.
However on affected systems, the Root Port is hotplug-capable and
pci_bridge_d3_possible() only allows hotplug ports to go to D3 if they
belong to a Thunderbolt device or if the Root Port possesses a
"HotPlugSupportInD3" ACPI property. Neither is the case on affected
laptops. The reason for whitelisting only specific, known to work
hotplug ports for D3 is that there have been reports of SkyLake Xeon-SP
systems raising Hardware Error NMIs upon suspending their hotplug ports:
https://lore.kernel.org/linux-pci/20170503180426.GA4058@otc-nc-03/
But if a hotplug port is power manageable by ACPI (as can be detected
through presence of Power Resources and corresponding _PS0 and _PS3
methods) then it ought to be safe to suspend it to D3. To this end,
amend acpi_pci_bridge_d3() to whitelist such ports for D3.
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/1222
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/1252
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/1304
Reported-and-tested-by: Arthur Borsboom <[email protected]>
Reported-and-tested-by: matoro <[email protected]>
Reported-by: Aaron Zakhrov <[email protected]>
Reported-by: Michal Rostecki <[email protected]>
Reported-by: Shai Coleman <[email protected]>
Signed-off-by: Lukas Wunner <[email protected]>
Acked-by: Alex Deucher <[email protected]>
Cc: 5.4+ <[email protected]> # 5.4+
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
Most of dma-debug.h is not required by anything outside of kernel/dma.
Move the four declarations needed by dma-mappin.h or dma-ops providers
into dma-mapping.h and dma-map-ops.h, and move the remainder of the
file to kernel/dma/debug.h.
Signed-off-by: Christoph Hellwig <[email protected]>
|
|
Split out all the bits that are purely for dma_map_ops implementations
and related code into a new <linux/dma-map-ops.h> header so that they
don't get pulled into all the drivers. That also means the architecture
specific <asm/dma-mapping.h> is not pulled in by <linux/dma-mapping.h>
any more, which leads to a missing includes that were pulled in by the
x86 or arm versions in a few not overly portable drivers.
Signed-off-by: Christoph Hellwig <[email protected]>
|
|
Enable pci-meson to build as a module whenever ARCH_MESON is enabled.
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Kevin Hilman <[email protected]>
Signed-off-by: Lorenzo Pieralisi <[email protected]>
Reviewed-by: Neil Armstrong <[email protected]>
Cc: Yue Wang <[email protected]>
|
|
We need the USB fixes in here as well for testing.
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
- Fix rockchip regression in rockchip_pcie_valid_device() (Lorenzo
Pieralisi)
- Add Pali Rohár as aardvark PCI maintainer (Pali Rohár)
* tag 'pci-v5.9-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
MAINTAINERS: Add Pali Rohár as aardvark PCI maintainer
PCI: rockchip: Fix bus checks in rockchip_pcie_valid_device()
|
|
Old ATF automatically power on pcie phy and does not provide SMC call for
phy power on functionality which leads to aardvark initialization failure:
[ 0.330134] mvebu-a3700-comphy d0018300.phy: unsupported SMC call, try updating your firmware
[ 0.338846] phy phy-d0018300.phy.1: phy poweron failed --> -95
[ 0.344753] advk-pcie d0070000.pcie: Failed to initialize PHY (-95)
[ 0.351160] advk-pcie: probe of d0070000.pcie failed with error -95
This patch fixes above failure by ignoring 'not supported' error in
aardvark driver. In this case it is expected that phy is already power on.
Tested-by: Tomasz Maciej Nowak <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Fixes: 366697018c9a ("PCI: aardvark: Add PHY support")
Signed-off-by: Pali Rohár <[email protected]>
Signed-off-by: Lorenzo Pieralisi <[email protected]>
Reviewed-by: Rob Herring <[email protected]>
Cc: <[email protected]> # 5.8+: ea17a0f153af: phy: marvell: comphy: Convert internal SMCC firmware return codes to errno
|
|
The value assigned to msi_val after the inner loop finishes its run is
never used for anything, and it is also immediately overridden in the
line that follows with the return value from the xgene_msi_int_read()
function.
Since the value of msi_val following the inner loop completion is never
used in any meaningful way the assignment can be removed.
Addresses-Coverity-ID: 1437183 ("Unused value")
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Krzysztof Wilczyński <[email protected]>
Signed-off-by: Lorenzo Pieralisi <[email protected]>
Reviewed-by: Rob Herring <[email protected]>
Acked-by: Bjorn Helgaas <[email protected]>
|
|
Simplify the return expression.
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Qinglang Miao <[email protected]>
Signed-off-by: Lorenzo Pieralisi <[email protected]>
Reviewed-by: Rob Herring <[email protected]>
|
|
expression
Simplify the return expression.
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Qinglang Miao <[email protected]>
Signed-off-by: Lorenzo Pieralisi <[email protected]>
Reviewed-by: Rob Herring <[email protected]>
|
|
Simplify the return expression by removing useless code.
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Liu Shixin <[email protected]>
Signed-off-by: Lorenzo Pieralisi <[email protected]>
Reviewed-by: Rob Herring <[email protected]>
|
|
module_bcma_driver() makes the code simpler by eliminating
boilerplate code.
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Liu Shixin <[email protected]>
Signed-off-by: Lorenzo Pieralisi <[email protected]>
Reviewed-by: Rob Herring <[email protected]>
Acked-by: Ray Jui <[email protected]>
|
|
Now that the support is in place with previous commits, we add several
chips that use the BrcmSTB driver.
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jim Quinlan <[email protected]>
Signed-off-by: Lorenzo Pieralisi <[email protected]>
Acked-by: Florian Fainelli <[email protected]>
Acked-by: Rob Herring <[email protected]>
|
|
The proper value of the parameter SCB_MAX_BURST_SIZE varies per chip. The
2711 family requires 128B whereas other devices can employ 512. The
assignment is complicated by the fact that the values for this two-bit
field have different meanings;
Value Type_Generic Type_7278
00 Reserved 128B
01 128B 256B
10 256B 512B
11 512B Reserved
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jim Quinlan <[email protected]>
Signed-off-by: Lorenzo Pieralisi <[email protected]>
Reviewed-by: Rob Herring <[email protected]>
Acked-by: Florian Fainelli <[email protected]>
|
|
Older BrcmSTB chips do not have a separate register for MSI interrupts; the
MSIs are in a register that also contains unrelated interrupts. In
addition, the interrupts lie in bits [31..24] for these legacy chips. This
commit provides common code for both legacy and non-legacy MSI interrupt
registers.
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jim Quinlan <[email protected]>
Signed-off-by: Lorenzo Pieralisi <[email protected]>
Reviewed-by: Rob Herring <[email protected]>
Acked-by: Florian Fainelli <[email protected]>
|
|
The Raspberry Pi (RPI) is currently the only chip using this driver
(pcie-brcmstb.c). There, only one memory controller is used, without an
extension region, and the SCB0 viewport size is set to the size of the
first and only dma-range region. Other BrcmSTB SOCs have more complicated
memory configurations that require setting additional viewport sizes.
BrcmSTB PCIe controllers are intimately connected to the memory
controller(s) on the SOC. The SOC may have one to three memory
controllers; they are indicated by the term SCBi. Each controller has a
base region and an optional extension region. In physical memory, the base
and extension regions of a controller are not adjacent, but in PCIe-space
they are.
There is a "viewport" for each memory controller that allows DMA from
endpoint devices. Each viewport's size must be set to a power of two, and
that size must be equal to or larger than the amount of memory each
controller supports which is the sum of base region and its optional
extension. Further, the 1-3 viewports are also adjacent in PCIe-space.
Unfortunately the viewport sizes cannot be ascertained from the
"dma-ranges" property so they have their own property, "brcm,scb-sizes".
This is because dma-range information does not indicate what memory
controller it is associated. For example, consider the following case
where the size of one dma-range is 2GB and the second dma-range is 1GB:
/* Case 1: SCB0 size set to 4GB */
dma-range0: 2GB (from memc0-base)
dma-range1: 1GB (from memc0-extension)
/* Case 2: SCB0 size set to 2GB, SCB1 size set to 1GB */
dma-range0: 2GB (from memc0-base)
dma-range1: 1GB (from memc0-extension)
By just looking at the dma-ranges information, one cannot tell which
situation applies. That is why an additional property is needed. Its
length indicates the number of memory controllers being used and each value
indicates the viewport size.
Note that the RPI DT does not have a "brcm,scb-sizes" property value,
as it is assumed that it only requires one memory controller and no
extension. So the optional use of "brcm,scb-sizes" will be backwards
compatible.
One last layer of complexity exists: all of the viewports sizes must be
added and rounded up to a power of two to determine what the "BAR" size is.
Further, an offset must be given that indicates the base PCIe address of
this "BAR". The use of the term BAR is typically associated with endpoint
devices, and the term is used here because the PCIe HW may be used as an RC
or an EP. In the former case, all of the system memory appears in a single
"BAR" region in PCIe memory. As it turns out, BrcmSTB PCIe HW is rarely
used in the EP role and its system of mapping memory is an artifact that
requires multiple dma-ranges regions.
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jim Quinlan <[email protected]>
Signed-off-by: Lorenzo Pieralisi <[email protected]>
Reviewed-by: Rob Herring <[email protected]>
Acked-by: Florian Fainelli <[email protected]>
|
|
Some STB chips have a special purpose reset controller named RESCAL (reset
calibration). The PCIe HW can now control RESCAL to start and stop its
operation. On probe(), the RESCAL is deasserted and the driver goes
through the sequence of setting registers and reading status in order to
start the internal PHY that is required for the PCIe.
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jim Quinlan <[email protected]>
Signed-off-by: Lorenzo Pieralisi <[email protected]>
Reviewed-by: Rob Herring <[email protected]>
Acked-by: Florian Fainelli <[email protected]>
|
|
pci_restore_msi_state() directly writes the MSI/MSI-X related registers
via MMIO. On a physical machine, this works perfectly; for a Linux VM
running on a hypervisor, which typically enables IOMMU interrupt remapping,
the hypervisor usually should trap and emulate the MMIO accesses in order
to re-create the necessary interrupt remapping table entries in the IOMMU,
otherwise the interrupts can not work in the VM after hibernation.
Hyper-V is different from other hypervisors in that it does not trap and
emulate the MMIO accesses, and instead it uses a para-virtualized method,
which requires the VM to call hv_compose_msi_msg() to notify the hypervisor
of the info that would be passed to the hypervisor in the case of the
trap-and-emulate method. This is not an issue to a lot of PCI device
drivers, which destroy and re-create the interrupts across hibernation, so
hv_compose_msi_msg() is called automatically. However, some PCI device
drivers (e.g. the in-tree GPU driver nouveau and the out-of-tree Nvidia
proprietary GPU driver) do not destroy and re-create MSI/MSI-X interrupts
across hibernation, so hv_pci_resume() has to call hv_compose_msi_msg(),
otherwise the PCI device drivers can no longer receive interrupts after
the VM resumes from hibernation.
Hyper-V is also different in that chip->irq_unmask() may fail in a
Linux VM running on Hyper-V (on a physical machine, chip->irq_unmask()
can not fail because unmasking an MSI/MSI-X register just means an MMIO
write): during hibernation, when a CPU is offlined, the kernel tries
to move the interrupt to the remaining CPUs that haven't been offlined
yet. In this case, hv_irq_unmask() -> hv_do_hypercall() always fails
because the vmbus channel has been closed: here the early "return" in
hv_irq_unmask() means the pci_msi_unmask_irq() is not called, i.e. the
desc->masked remains "true", so later after hibernation, the MSI interrupt
always remains masked, which is incorrect. Refer to cpu_disable_common()
-> fixup_irqs() -> irq_migrate_all_off_this_cpu() -> migrate_one_irq():
static bool migrate_one_irq(struct irq_desc *desc)
{
...
if (maskchip && chip->irq_mask)
chip->irq_mask(d);
...
err = irq_do_set_affinity(d, affinity, false);
...
if (maskchip && chip->irq_unmask)
chip->irq_unmask(d);
Fix the issue by calling pci_msi_unmask_irq() unconditionally in
hv_irq_unmask(). Also suppress the error message for hibernation because
the hypercall failure during hibernation does not matter (at this time
all the devices have been frozen). Note: the correct affinity info is
still updated into the irqdata data structure in migrate_one_irq() ->
irq_do_set_affinity() -> hv_set_affinity(), so later when the VM
resumes, hv_pci_restore_msi_state() is able to correctly restore
the interrupt with the correct affinity.
Link: https://lore.kernel.org/r/[email protected]
Fixes: ac82fc832708 ("PCI: hv: Add hibernation support")
Signed-off-by: Dexuan Cui <[email protected]>
Signed-off-by: Lorenzo Pieralisi <[email protected]>
Reviewed-by: Jake Oshins <[email protected]>
|
|
Add Kconfig options for changing the default pcie_bus_config, i.e., the
strategy for configuration MPS and MRRS, in the same manner as the
CONFIG_PCIEASPM_XXXX choice. The pci_bus_config setting may still be
overridden by kernel command-line parameters, e.g.,
"pci=pcie_bus_tune_off".
[bhelgaas: depend on EXPERT, tweak help texts]
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jim Quinlan <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
|
|
This reverts commit 7e24bc347e57992d532bc2ed700209b0fc0a4bf5.
7e24bc347e57 was based on PCIe r5.0, sec 5.9, which claims we need a 200 ms
delay when transitioning to or from D2. However, sec 5.3.1.3 states the
delay as 200 μs (microseconds), as does the table in PCIe r4.0, sec 5.9.1.
This looks like a typo in the r5.0 spec, so revert back to a 200 μs delay
instead of a 200 ms delay.
Fixes: 7e24bc347e57 ("PCI/PM: Apply D2 delay as milliseconds, not microseconds")
Signed-off-by: Bjorn Helgaas <[email protected]>
Reviewed-by: Rafael J. Wysocki <[email protected]>
|
|
476e7faefc43 ("PCI PM: Do not wait for buses in B2 or B3 during resume")
removed the last use of PCI_PM_BUS_WAIT. Remove the definition as well.
Signed-off-by: Bjorn Helgaas <[email protected]>
Reviewed-by: Rafael J. Wysocki <[email protected]>
|
|
sg_init_table() zeroes its first argument, so the allocation of that
argument doesn't have to.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x;
@@
x =
- kzalloc
+ kmalloc
(...)
...
sg_init_table(x,...)
// </smpl>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Julia Lawall <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
|
|
Take care about Coccinelle warnings:
drivers/pci/pci.c:6008:6-12: WARNING: Comparison to bool
drivers/pci/pci.c:6024:7-13: WARNING: Comparison to bool
No change to functionality intended.
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Krzysztof Wilczyński <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-next
Mika writes:
thunderbolt: Changes for v5.10 merge window
This includes following Thunderbolt/USB4 changes for v5.10 merge window:
* A couple of optimizations around Tiger Lake force power logic and
NHI (Native Host Interface) LC (Link Controller) mailbox command
processing
* Power management improvements for Software Connection Manager
* Debugfs support
* Allow KUnit tests to be enabled also when Thunderbolt driver is
configured as module.
* Few minor cleanups and fixes
All these have been in linux-next with no reported issues.
* tag 'thunderbolt-for-v5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt: (37 commits)
thunderbolt: Capitalize comment on top of QUIRK_FORCE_POWER_LINK_CONTROLLER
thunderbolt: Correct tb_check_quirks() kernel-doc
thunderbolt: Log correct zeroX entries in decode_error()
thunderbolt: Handle ERR_LOCK notification
thunderbolt: Use "if USB4" instead of "depends on" in Kconfig
thunderbolt: Allow KUnit tests to be built also when CONFIG_USB4=m
thunderbolt: Only stop control channel when entering freeze
thunderbolt: debugfs: Fix uninitialized return in counters_write()
thunderbolt: Add debugfs interface
thunderbolt: No need to warn in TB_CFG_ERROR_INVALID_CONFIG_SPACE
thunderbolt: Introduce tb_switch_is_tiger_lake()
thunderbolt: Introduce tb_switch_is_ice_lake()
thunderbolt: Check for Intel vendor ID when identifying controller
thunderbolt: Introduce tb_port_is_nhi()
thunderbolt: Introduce tb_switch_next_cap()
thunderbolt: Introduce tb_port_next_cap()
thunderbolt: Move struct tb_cap_any to tb_regs.h
thunderbolt: Add runtime PM for Software CM
thunderbolt: Create device links from ACPI description
ACPI: Export acpi_get_first_physical_node() to modules
...
|
|
PCI devices support two variants of the D3 power state: D3hot (main power
present) D3cold (main power removed). Previously struct pci_dev contained:
unsigned int d3_delay; /* D3->D0 transition time in ms */
unsigned int d3cold_delay; /* D3cold->D0 transition time in ms */
"d3_delay" refers specifically to the D3hot state. Rename it to
"d3hot_delay" to avoid ambiguity and align with the ACPI "_DSM for
Specifying Device Readiness Durations" in the PCI Firmware spec r3.2,
sec 4.6.9.
There is no change to the functionality.
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Krzysztof Wilczyński <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
|
|
The "struct dev_pm_ops pcibios_pm_ops", declared in include/linux/pci.h and
defined in drivers/pci/pci-driver.c, provided arch-specific hooks when a
PCI device was doing a hibernate transition.
394216275c7d ("s390: remove broken hibernate / power management support")
removed the last use of pcibios_pm_ops, so remove it completely.
[bhelgaas: drop unused "error"]
Link: https://lore.kernel.org/r/[email protected]
Reported-by: Bjorn Helgaas <[email protected]>
Signed-off-by: Vaibhav Gupta <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
|
|
The value of the constant POWER_FAILURE assigned to the variable rc
after the power fault check is never used for anything, so remove it.
Addresses-Coverity-ID: 1226899 ("Unused value")
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Krzysztof Wilczyński <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
|
|
PCI host bridge driver can be probed before the gpiochip it requires,
so, of_get_named_gpio() can return -EPROBE_DEFER. Current code lets the
kirin_pcie_probe() directly return -ENODEV, which results in the PCI
host controller driver probe failure; with this error code the PCI host
controller driver will not be probed again when the gpiochip driver is
loaded.
Fix the above issue by letting kirin_pcie_probe() return -EPROBE_DEFER in
such a case.
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Bean Huo <[email protected]>
[[email protected]: commit log]
Signed-off-by: Lorenzo Pieralisi <[email protected]>
|
|
Fixes warning given by executing "make C=2 drivers/pci/"
Sparse output:
CHECK drivers/pci/controller/dwc/pcie-designware.c
drivers/pci/controller/dwc/pcie-designware.c:432:52: warning:
cast truncates bits from constant value (ffffffff7fffffff becomes
7fffffff)
Link: https://lore.kernel.org/r/7ea7f7d342f97c758949a17b870012f52ce5b3f5.1600767645.git.gustavo.pimentel@synopsys.com
Reported-by: Bjorn Helgaas <[email protected]>
Signed-off-by: Gustavo Pimentel <[email protected]>
Signed-off-by: Lorenzo Pieralisi <[email protected]>
Cc: Joao Pinto <[email protected]>
|
|
Use DEFINE_SEQ_ATTRIBUTE macro to simplify the code.
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Liu Shixin <[email protected]>
Signed-off-by: Lorenzo Pieralisi <[email protected]>
Acked-by: Thierry Reding <[email protected]>
|
|
Add missing documentation for the parameter "version" and "num_version"
of the hv_pci_protocol_negotiation() function and resolve build time
kernel-doc warnings:
drivers/pci/controller/pci-hyperv.c:2535: warning: Function parameter
or member 'version' not described in 'hv_pci_protocol_negotiation'
drivers/pci/controller/pci-hyperv.c:2535: warning: Function parameter
or member 'num_version' not described in 'hv_pci_protocol_negotiation'
No change to functionality intended.
Signed-off-by: Krzysztof Wilczyński <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Reviewed-by: Michael Kelley <[email protected]>
Signed-off-by: Wei Liu <[email protected]>
|
|
Add PCIe EP mode support for ls1088a and ls2088a, there are some
difference between LS1 and LS2 platform, so refactor the code of
the EP driver.
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Xiaowei Bao <[email protected]>
Signed-off-by: Hou Zhiqiang <[email protected]>
Signed-off-by: Lorenzo Pieralisi <[email protected]>
Reviewed-by: Rob Herring <[email protected]>
|
|
dw_pcie_ep_raise_msix_irq was never called in the exisitng driver
before, because the ls1046a platform don't support the MSIX feature
and msix_capable was always set to false.
Now that add the ls1088a platform with MSIX support, use the doorbell
method to support the MSIX feature.
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Xiaowei Bao <[email protected]>
Signed-off-by: Hou Zhiqiang <[email protected]>
Signed-off-by: Lorenzo Pieralisi <[email protected]>
Reviewed-by: Andrew Murray <[email protected]>
|
|
The different PCIe controller in one board may be have different
capability of MSI or MSIX, so change the way of getting the MSI
capability, make it more flexible.
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Xiaowei Bao <[email protected]>
Signed-off-by: Hou Zhiqiang <[email protected]>
Signed-off-by: Lorenzo Pieralisi <[email protected]>
Reviewed-by: Rob Herring <[email protected]>
|
|
Fix some format issue of the code in EP driver.
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Xiaowei Bao <[email protected]>
Signed-off-by: Hou Zhiqiang <[email protected]>
Signed-off-by: Lorenzo Pieralisi <[email protected]>
Reviewed-by: Andrew Murray <[email protected]>
|
|
Each PF of EP device should have its own MSI or MSIX capabitily
struct, so create a dw_pcie_ep_func struct and move the msi_cap
and msix_cap to this struct from dw_pcie_ep, and manage the PFs
via a list.
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Xiaowei Bao <[email protected]>
Signed-off-by: Hou Zhiqiang <[email protected]>
Signed-off-by: Lorenzo Pieralisi <[email protected]>
|
|
Move the function of getting MSI capability to the front of init
function, because the init function of the EP platform driver will use
the return value by the function of getting MSI capability.
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Xiaowei Bao <[email protected]>
Signed-off-by: Hou Zhiqiang <[email protected]>
Signed-off-by: Lorenzo Pieralisi <[email protected]>
Reviewed-by: Andrew Murray <[email protected]>
|
|
Add the doorbell mode of MSI-X in DWC EP driver.
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Xiaowei Bao <[email protected]>
Signed-off-by: Hou Zhiqiang <[email protected]>
Signed-off-by: Lorenzo Pieralisi <[email protected]>
Reviewed-by: Andrew Murray <[email protected]>
|
|
Add multiple PFs support for DWC, due to different PF have different
config space, we use func_conf_select callback function to access
the different PF's config space, the different chip company need to
implement this callback function when use the DWC IP core and intend
to support multiple PFs feature.
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Xiaowei Bao <[email protected]>
Signed-off-by: Hou Zhiqiang <[email protected]>
Signed-off-by: Lorenzo Pieralisi <[email protected]>
Reviewed-by: Rob Herring <[email protected]>
Acked-by: Gustavo Pimentel <[email protected]>
|
|
pci_dev_reset_slot_function() refuses to reset a hotplug slot if it is
shared by multiple pci_devs. That's the case if and only if the slot is
occupied by a multifunction device.
Simplify the function to check the device's multifunction flag instead
of iterating over the devices on the bus. (Iterating over the devices
requires holding pci_bus_sem, which the function erroneously does not
acquire.)
Link: https://lore.kernel.org/r/c6aab5af096f7b1b3db57f6335cebba8f0fcca89.1595330431.git.lukas@wunner.de
Signed-off-by: Lukas Wunner <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
Cc: Alex Williamson <[email protected]>
|
|
When a PCIe card is hot-removed, the Presence Detect State and Data Link
Layer Link Active bits often do not clear simultaneously. I've seen delays
of up to 244 msec between the two events with Thunderbolt.
After pciehp has brought down the slot in response to the first event, the
other bit may still be set. It's not discernible whether it's set because
a new card is already in the slot or if it will soon clear. So pciehp
tries to bring up the slot and in the latter case fails with a bunch of
messages, some of them at KERN_ERR severity. If the slot is no longer
occupied, the messages are false positives and annoy users.
Stuart Hayes reports the following splat on hot removal:
KERN_INFO pcieport 0000:3c:06.0: pciehp: Slot(180): Link Up
KERN_INFO pcieport 0000:3c:06.0: pciehp: Timeout waiting for Presence Detect
KERN_ERR pcieport 0000:3c:06.0: pciehp: link training error: status 0x0001
KERN_ERR pcieport 0000:3c:06.0: pciehp: Failed to check link status
Dongdong Liu complains about a similar splat:
KERN_INFO pciehp 0000:80:10.0:pcie004: Slot(36): Link Down
KERN_INFO iommu: Removing device 0000:87:00.0 from group 12
KERN_INFO pciehp 0000:80:10.0:pcie004: Slot(36): Card present
KERN_INFO pcieport 0000:80:10.0: Data Link Layer Link Active not set in 1000 msec
KERN_ERR pciehp 0000:80:10.0:pcie004: Failed to check link status
Users are particularly irritated to see a bringup attempt even though the
slot was explicitly brought down via sysfs. In a perfect world, we could
avoid this by setting Link Disable on slot bringdown and re-enabling it
upon a Presence Detect State change. In reality however, there are broken
hotplug ports which hardwire Presence Detect to zero, see 80696f991424
("PCI: pciehp: Tolerate Presence Detect hardwired to zero"). Conversely,
PCIe r1.0 hotplug ports hardwire Link Active to zero because Link Active
Reporting wasn't specified before PCIe r1.1. On unplug, some ports first
clear Presence then Link (see Stuart Hayes' splat) whereas others use the
inverse order (see Dongdong Liu's splat). To top it off, there are hotplug
ports which flap the Presence and Link bits on slot bringup, see
6c35a1ac3da6 ("PCI: pciehp: Tolerate initially unstable link").
pciehp is designed to work with all of these variants. Surplus attempts at
slot bringup are a lesser evil than not being able to bring up slots at
all. Although we could try to perfect the behavior for specific hotplug
controllers, we'd risk breaking others or increasing code complexity.
But we can certainly minimize annoyance by emitting only a single message
with KERN_INFO severity if bringup is unsuccessful:
* Drop the "Timeout waiting for Presence Detect" message in
pcie_wait_for_presence(). The sole caller of that function,
pciehp_check_link_status(), ignores the timeout and carries on. It emits
error messages of its own and I don't think this particular message adds
much value.
* There's a single error condition in pciehp_check_link_status() which
does not emit a message. Adding one allows dropping the "Failed to check
link status" message emitted by board_added() if
pciehp_check_link_status() returns a non-zero integer.
* Tone down all messages in pciehp_check_link_status() to KERN_INFO
severity and rephrase them to look as innocuous as possible. To this
end, move the message emitted by pcie_wait_for_link_delay() to its
callers.
As a result, Stuart Hayes' splat becomes:
KERN_INFO pcieport 0000:3c:06.0: pciehp: Slot(180): Link Up
KERN_INFO pcieport 0000:3c:06.0: pciehp: Slot(180): Cannot train link: status 0x0001
Dongdong Liu's splat becomes:
KERN_INFO pciehp 0000:80:10.0:pcie004: Slot(36): Card present
KERN_INFO pciehp 0000:80:10.0:pcie004: Slot(36): No link
The messages now merely serve as information that presence or link bits
were set a little longer than expected. Bringup failures which are not
false positives are still reported, albeit no longer at KERN_ERR severity.
Link: https://lore.kernel.org/linux-pci/[email protected]/
Link: https://lore.kernel.org/linux-pci/[email protected]/
Link: https://lore.kernel.org/r/b45e46fd8a6aa6930aaac9d7718c2e4b787a4e5e.1595935071.git.lukas@wunner.de
Reported-by: Stuart Hayes <[email protected]>
Reported-by: Dongdong Liu <[email protected]>
Signed-off-by: Lukas Wunner <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
Reviewed-by: Mika Westerberg <[email protected]>
|
|
Use for_each_child_of_node() and for_each_node_by_name() macros instead of
open coding them.
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Qinglang Miao <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
|
|
f719582435af ("PCI: Add pci_mmap_resource_range() and use it for ARM64")
changed the #ifdef condition around pci_create_resource_files(),
pci_remove_resource_files(), and related functions, but did not update
comments at the #else and #ifdef.
Update the comments to match the #ifdef.
[bhelgaas: commit log, drop #endif comment since it's close to the #else]
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Clint Sbisa <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
|
|
Print the IRQ used by PCIe Link Bandwidth Notification services port as
AER, PME and DPC do. It provides convenience to track PCIe BW notification
interrupt counts of certain port from /proc/interrupts.
The dmesg log is as below:
pcieport 0000:00:00.0: bw_notification: enabled with IRQ 1166
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Dongdong Liu <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
|