| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
- Make pcie_port_bus_type const (Ricardo B. Marliere)
* pci/misc:
PCI: Make pcie_port_bus_type const
|
|
- Disable use of D3cold on Asus B1400 PCI-NVMe bridges because some BIOSes
can't power them back on, replacing a more general ACPI sleep quirk
(Daniel Drake)
- Allow runtime PM when the driver enables it but doesn't need any runtime
PM callbacks (Raag Jadav)
- Drain runtime-idle callbacks before driver removal to avoid races between
.remove() and .runtime_idle(), which caused intermittent page faults when
the rtsx .runtime_idle() accessed registers that its .remove() had
already unmapped (Rafael J. Wysocki)
* pci/pm:
PCI/PM: Drain runtime-idle callbacks before driver removal
PCI/PM: Allow runtime PM with no PM callbacks at all
Revert "ACPI: PM: Block ASUS B1400CEAE from suspend to idle by default"
PCI: Disable D3cold on Asus B1400 PCI-NVMe bridge
|
|
A race condition between the .runtime_idle() callback and the .remove()
callback in the rtsx_pcr PCI driver leads to a kernel crash due to an
unhandled page fault [1].
The problem is that rtsx_pci_runtime_idle() is not expected to be running
after pm_runtime_get_sync() has been called, but the latter doesn't really
guarantee that. It only guarantees that the suspend and resume callbacks
will not be running when it returns.
However, if a .runtime_idle() callback is already running when
pm_runtime_get_sync() is called, the latter will notice that the runtime PM
status of the device is RPM_ACTIVE and it will return right away without
waiting for the former to complete. In fact, it cannot wait for
.runtime_idle() to complete because it may be called from that callback (it
arguably does not make much sense to do that, but it is not strictly
prohibited).
Thus in general, whoever is providing a .runtime_idle() callback needs
to protect it from running in parallel with whatever code runs after
pm_runtime_get_sync(). [Note that .runtime_idle() will not start after
pm_runtime_get_sync() has returned, but it may continue running then if it
has started earlier.]
One way to address that race condition is to call pm_runtime_barrier()
after pm_runtime_get_sync() (not before it, because a nonzero value of the
runtime PM usage counter is necessary to prevent runtime PM callbacks from
being invoked) to wait for the .runtime_idle() callback to complete should
it be running at that point. A suitable place for doing that is in
pci_device_remove() which calls pm_runtime_get_sync() before removing the
driver, so it may as well call pm_runtime_barrier() subsequently, which
will prevent the race in question from occurring, not just in the rtsx_pcr
driver, but in any PCI drivers providing .runtime_idle() callbacks.
Link: https://lore.kernel.org/lkml/20240229062201.49500-1-kai.heng.feng@canonical.com/ # [1]
Link: https://lore.kernel.org/r/5761426.DvuYhMxLoT@kreacher
Reported-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Ricky Wu <ricky_wu@realtek.com>
Acked-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: <stable@vger.kernel.org>
|
|
Commit c5eb1190074c ("PCI / PM: Allow runtime PM without callback
functions") eliminated the need for PM callbacks in
pci_pm_runtime_suspend() and pci_pm_runtime_resume(), but
didn't do the same for pci_pm_runtime_idle().
Therefore, runtime suspend worked as long as the driver implemented at
least one PM callback. But if the driver doesn't implement any PM
callbacks at all (driver->pm is NULL), pci_pm_runtime_idle() returned
-ENOSYS, which prevented runtime suspend.
Modify pci_pm_runtime_idle() to allow PCI device power state transitions
without runtime PM callbacks and complete the original intention of commit
c5eb1190074c ("PCI / PM: Allow runtime PM without callback functions").
Link: https://lore.kernel.org/r/20240227062648.16579-1-raag.jadav@intel.com
Signed-off-by: Raag Jadav <raag.jadav@intel.com>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
|
|
Now that the driver core can properly handle constant struct bus_type, move
the pcie_port_bus_type variable to be a constant structure as well, placing
it into read-only memory which can not be modified at runtime.
Link: https://lore.kernel.org/r/20240208-bus_cleanup-pci2-v1-1-5e578210b6f2@marliere.net
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Interrupt related code is spread into irq.c, pci.c, and setup-irq.c.
Group them into pre-existing irq.c.
Link: https://lore.kernel.org/r/20240129113655.3368-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Mark Blakeney reported that when suspending system with a Thunderbolt
dock connected and then unplugging the dock before resume (which is
pretty normal flow with laptops), resuming takes long time.
What happens is that the PCIe link from the root port to the PCIe switch
inside the Thunderbolt device does not train (as expected, the link is
unplugged):
pcieport 0000:00:07.2: restoring config space at offset 0x24 (was 0x3bf12001, writing 0x3bf12001)
pcieport 0000:00:07.0: waiting 100 ms for downstream link
pcieport 0000:01:00.0: not ready 1023ms after resume; giving up
However, at this point we still try to resume the devices below that
unplugged link:
pcieport 0000:01:00.0: Unable to change power state from D3cold to D0, device inaccessible
...
pcieport 0000:01:00.0: restoring config space at offset 0x38 (was 0xffffffff, writing 0x0)
...
pcieport 0000:02:02.0: waiting 100 ms for downstream link, after activation
And this is the link from PCIe switch downstream port to the xHCI on the
dock:
xhci_hcd 0000:03:00.0: not ready 65535ms after resume; giving up
xhci_hcd 0000:03:00.0: Unable to change power state from D3cold to D0, device inaccessible
xhci_hcd 0000:03:00.0: restoring config space at offset 0x3c (was 0xffffffff, writing 0x1ff)
This ends up slowing down the resume time considerably. For this reason
mark these devices as disconnected if the link above them did not train
properly.
Fixes: e8b908146d44 ("PCI/PM: Increase wait time after resume")
Link: https://lore.kernel.org/r/20230918053041.1018876-1-mika.westerberg@linux.intel.com
Reported-by: Mark Blakeney <mark.blakeney@bullet-systems.net>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217915
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v6.4+
|
|
Simplify pci_dev_driver() by removing the "else". The "if" case always
returns, so the "else" is superfluous. No functional change intended.
Link: https://lore.kernel.org/r/20230824193712.542167-9-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
We always assign "fields" immediately, so remove the unnecessary
initializations. No functional change intended.
Link: https://lore.kernel.org/r/20230824193712.542167-4-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
pcie_port_bus_type is used only in pci-driver.c and pcie/portdrv_core.c and
pcie/portdrv_pci.c. None of these can be built as modules, so
pcie_port_bus_type doesn't need to be exported. Unexport it.
Link: https://lore.kernel.org/r/20230824193712.542167-3-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
All callers of pci_bridge_wait_for_secondary_bus() supply a timeout of
PCIE_RESET_READY_POLL_MS, so drop the parameter. Move the definition of
PCIE_RESET_READY_POLL_MS into pci.c, the only user.
[bhelgaas: extracted from
https://lore.kernel.org/r/20230404052714.51315-3-mika.westerberg@linux.intel.com]
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
PCIe r6.0 sec 6.6.1 prescribes that a device must be able to respond to
config requests within 1.0 s (PCI_RESET_WAIT) after exiting conventional
reset and this same delay is prescribed when coming out of D3cold (as that
involves reset too).
A device that requires more than 1 second to initialize after reset may
respond to config requests with Request Retry Status completions (sec
2.3.1), and we accommodate that in Linux with a 60 second cap
(PCIE_RESET_READY_POLL_MS).
Previously we waited up to PCIE_RESET_READY_POLL_MS only in the reset code
path, not in the resume path. However, a device has surfaced, namely Intel
Titan Ridge xHCI, which requires a longer delay also in the resume code
path.
Make the resume code path to use this same extended delay as the reset
path.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216728
Link: https://lore.kernel.org/r/20230404052714.51315-2-mika.westerberg@linux.intel.com
Reported-by: Chris Chiu <chris.chiu@canonical.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lukas Wunner <lukas@wunner.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Rework portdrv shutdown so it disables interrupts but doesn't
disable bus mastering, which leads to hangs on Loongson LS7A
- Add mechanism to prevent Max_Read_Request_Size (MRRS) increases,
again to avoid hardware issues on Loongson LS7A (and likely other
devices based on DesignWare IP)
- Ignore devices with a firmware (DT or ACPI) node that says the
device is disabled
Resource management:
- Distribute spare resources to unconfigured hotplug bridges at
boot-time (not just when hot-adding such a bridge), which makes
hot-adding devices to docks work better. Tried this in v6.1 but had
to revert for regressions, so try again
- Fix root bus issue that dropped resources that happened to end
at 0, e.g., [bus 00]
PCI device hotplug:
- Remove device locking when marking device as disconnected so this
doesn't have to wait for concurrent driver bind/unbind to complete
- Quirk more Qualcomm bridges that don't fully implement the PCIe
Slot Status 'Command Completed' bit
Power management:
- Account for _S0W of the target bridge in acpi_pci_bridge_d3() so we
don't miss hot-add notifications for USB4 docks, Thunderbolt, etc
Reset:
- Observe delay after reset, e.g., resuming from system sleep,
regardless of whether a bridge can suspend to D3cold at runtime
- Wait for secondary bus to become ready after a bridge reset
Virtualization:
- Avoid FLR on some AMD FCH AHCI adapters where it doesn't work
- Allow independent IOMMU groups for some Wangxun NICs that prevent
peer-to-peer transactions but don't advertise an ACS Capability
Error handling:
- Configure End-to-End-CRC (ECRC) only if Linux owns the AER
Capability
- Remove redundant Device Control Error Reporting Enable in the AER
service driver since this is already done for all devices during
enumeration
ASPM:
- Add pci_enable_link_state() interface to allow drivers to enable
ASPM link state
Endpoint framework:
- Move dra7xx and tegra194 linkup processing from hard IRQ to
threaded IRQ handler
- Add a separate lock for endpoint controller list of endpoint
function drivers to prevent deadlock in callbacks
- Pass events from endpoint controller to endpoint function drivers
via callbacks instead of notifiers
Synopsys DesignWare eDMA controller driver (acked by Vinod):
- Fix CPU vs PCI address issues
- Fix source vs destination address issues
- Fix issues with interleaved transfer semantics
- Fix channel count initialization issue (issue still exists in
several other drivers)
- Clean up and improve debugfs usage so it will work on platforms
with several eDMA devices
Baikal T-1 PCIe controller driver:
- Set a 64-bit DMA mask
Freescale i.MX6 PCIe controller driver:
- Add i.MX8MM, i.MX8MQ, i.MX8MP endpoint mode DT binding and driver
support
Intel VMD host bridge driver:
- Add quirk to configure PCIe ASPM and LTR. This is normally done by
BIOS, and will be for future products
Marvell MVEBU PCIe controller driver:
- Mark this driver as broken in Kconfig since bugs prevent its daily
usage
MediaTek MT7621 PCIe controller driver:
- Delay PHY port initialization to improve boot reliability for ZBT
WE1326, ZBT WF3526-P, and some Netgear models
Qualcomm PCIe controller driver:
- Add MSM8998 DT compatible string
- Unify MSM8996 and MSM8998 clock orderings
- Add SM8350 DT binding and driver support
- Add IPQ8074 Gen3 DT binding and driver support
- Correct qcom,perst-regs in DT binding
- Add qcom_pcie_host_deinit() so the PHY is powered off and
regulators and clocks are disabled on late host-init errors
Socionext UniPhier Pro5 controller driver:
- Clean up uniphier-ep reg, clocks, resets, and their names in DT
binding
Synopsys DesignWare PCIe controller driver:
- Restrict coherent DMA mask to 32 bits for MSI, but allow controller
drivers to set 64-bit streaming DMA mask
- Add eDMA engine support in both Root Port and Endpoint controllers
Miscellaneous:
- Remove MODULE_LICENSE from boolean drivers so they don't look like
modules so modprobe can complain about them"
* tag 'pci-v6.3-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (86 commits)
PCI: dwc: Add Root Port and Endpoint controller eDMA engine support
PCI: bt1: Set 64-bit DMA mask
PCI: dwc: Restrict only coherent DMA mask for MSI address allocation
dmaengine: dw-edma: Prepare dw_edma_probe() for builtin callers
dmaengine: dw-edma: Depend on DW_EDMA instead of selecting it
dmaengine: dw-edma: Add mem-mapped LL-entries support
PCI: Remove MODULE_LICENSE so boolean drivers don't look like modules
PCI: hv: Drop duplicate PCI_MSI dependency
PCI/P2PDMA: Annotate RCU dereference
PCI/sysfs: Constify struct kobj_type pci_slot_ktype
PCI: hotplug: Allow marking devices as disconnected during bind/unbind
PCI: pciehp: Add Qualcomm quirk for Command Completed erratum
PCI: qcom: Add IPQ8074 Gen3 port support
dt-bindings: PCI: qcom: Add IPQ8074 Gen3 port
dt-bindings: PCI: qcom: Sort compatibles alphabetically
PCI: qcom: Fix host-init error handling
PCI: qcom: Add SM8350 support
dt-bindings: PCI: qcom: Add SM8350
dt-bindings: PCI: qcom-ep: Correct qcom,perst-regs
dt-bindings: PCI: qcom: Unify MSM8996 and MSM8998 clock order
...
|
|
Sheng Bi reports that pci_bridge_secondary_bus_reset() may fail to wait
for devices on the secondary bus to become accessible after reset:
Although it does call pci_dev_wait(), it erroneously passes the bridge's
pci_dev rather than that of a child. The bridge of course is always
accessible while its secondary bus is reset, so pci_dev_wait() returns
immediately.
Sheng Bi proposes introducing a new pci_bridge_secondary_bus_wait()
function which is called from pci_bridge_secondary_bus_reset():
https://lore.kernel.org/linux-pci/20220523171517.32407-1-windy.bi.enflame@gmail.com/
However we already have pci_bridge_wait_for_secondary_bus() which does
almost exactly what we need. So far it's only called on resume from
D3cold (which implies a Fundamental Reset per PCIe r6.0 sec 5.8).
Re-using it for Secondary Bus Resets is a leaner and more rational
approach than introducing a new function.
That only requires a few minor tweaks:
- Amend pci_bridge_wait_for_secondary_bus() to await accessibility of
the first device on the secondary bus by calling pci_dev_wait() after
performing the prescribed delays. pci_dev_wait() needs two parameters,
a reset reason and a timeout, which callers must now pass to
pci_bridge_wait_for_secondary_bus(). The timeout is 1 sec for resume
(PCIe r6.0 sec 6.6.1) and 60 sec for reset (commit 821cdad5c46c ("PCI:
Wait up to 60 seconds for device to become ready after FLR")).
Introduce a PCI_RESET_WAIT macro for the 1 sec timeout.
- Amend pci_bridge_wait_for_secondary_bus() to return 0 on success or
-ENOTTY on error for consumption by pci_bridge_secondary_bus_reset().
- Drop an unnecessary 1 sec delay from pci_reset_secondary_bus() which
is now performed by pci_bridge_wait_for_secondary_bus(). A static
delay this long is only necessary for Conventional PCI, so modern
PCIe systems benefit from shorter reset times as a side effect.
Fixes: 6b2f1351af56 ("PCI: Wait for device to become ready after secondary bus reset")
Link: https://lore.kernel.org/r/da77c92796b99ec568bd070cbe4725074a117038.1673769517.git.lukas@wunner.de
Reported-by: Sheng Bi <windy.bi.enflame@gmail.com>
Tested-by: Ravi Kishore Koppuravuri <ravi.kishore.koppuravuri@intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Cc: stable@vger.kernel.org # v4.17+
|
|
The uevent() callback in struct bus_type should not be modifying the
device that is passed into it, so mark it as a const * and propagate the
function signature changes out into all relevant subsystems that use
this callback.
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230111113018.459199-16-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
1a1daf097e21 ("PCI/PM: Remove unused pci_driver.suspend_late() hook")
removed the legacy .suspend_late() hook, which was the only user of the
"state" parameter to pci_legacy_suspend_late(), but it neglected to remove
the parameter.
Remove the unused "state" parameter to pci_legacy_suspend_late().
Link: https://lore.kernel.org/r/20221025193502.669091-1-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
We always want to save the device state unless the driver has already done
it. Rearrange the checking in pci_pm_suspend_noirq() to make this more
clear. No functional change intended.
[bhelgaas: commit log, rewrap comment]
Link: https://lore.kernel.org/r/20220830104913.1620539-1-rajvi.jingar@linux.intel.com
Signed-off-by: Rajvi Jingar <rajvi.jingar@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
We want to disable PTM on Root Ports because that allows some chips, e.g.,
Intel mobile chips since Coffee Lake, to enter a lower-power PM state.
That means we also have to disable PTM on downstream devices. PCIe r6.0,
sec 2.2.8, recommends that functions support generation of messages in
non-D0 states, so we have to assume Switch Upstream Ports or Endpoints may
send PTM Requests while in D1, D2, and D3hot. A PTM message received by a
Downstream Port (including a Root Port) with PTM disabled must be treated
as an Unsupported Request (sec 6.21.3).
PTM was previously disabled only for Root Ports, and it was disabled in
pci_prepare_to_sleep(), which is not called at all if a driver supports
legacy PM or does its own state saving.
Instead, disable PTM early in pci_pm_suspend() and pci_pm_runtime_suspend()
so we do it in all cases.
Previously PTM was disabled *after* saving device state, so the state
restore on resume automatically re-enabled it. Since we now disable PTM
*before* saving state, we must explicitly re-enable it in pci_pm_resume()
and pci_pm_runtime_resume().
Here's a sample of errors that occur when PTM is disabled only on the Root
Port. With this topology:
0000:00:1d.0 Root Port to [bus 08-71]
0000:08:00.0 Switch Upstream Port to [bus 09-71]
Kai-Heng reported errors like this:
pcieport 0000:00:1d.0: [20] UnsupReq (First)
pcieport 0000:00:1d.0: AER: TLP Header: 34000000 08000052 00000000 00000000
Decoding TLP header 0x34...... (0011 0100b) and 0x08000052:
Fmt 001b 4 DW header, no data
Type 1 0100b Msg (Local - Terminate at Receiver)
Requester ID 0x0800 Bus 08 Devfn 00.0
Message Code 0x52 0101 0010b PTM Request
The 00:1d.0 Root Port logged an Unsupported Request error when it received
a PTM Request with Requester ID 08:00.0.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=215453
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=216210
Fixes: a697f072f5da ("PCI: Disable PTM during suspend to save power")
Link: https://lore.kernel.org/r/20220909202505.314195-10-helgaas@kernel.org
Reported-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Rajvi Jingar <rajvi.jingar@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu updates from Joerg Roedel:
- Intel VT-d driver updates:
- Domain force snooping improvement.
- Cleanups, no intentional functional changes.
- ARM SMMU driver updates:
- Add new Qualcomm device-tree compatible strings
- Add new Nvidia device-tree compatible string for Tegra234
- Fix UAF in SMMUv3 shared virtual addressing code
- Force identity-mapped domains for users of ye olde SMMU legacy
binding
- Minor cleanups
- Fix a BUG_ON in the vfio_iommu_group_notifier:
- Groundwork for upcoming iommufd framework
- Introduction of DMA ownership so that an entire IOMMU group is
either controlled by the kernel or by user-space
- MT8195 and MT8186 support in the Mediatek IOMMU driver
- Make forcing of cache-coherent DMA more coherent between IOMMU
drivers
- Fixes for thunderbolt device DMA protection
- Various smaller fixes and cleanups
* tag 'iommu-updates-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (88 commits)
iommu/amd: Increase timeout waiting for GA log enablement
iommu/s390: Tolerate repeat attach_dev calls
iommu/vt-d: Remove hard coding PGSNP bit in PASID entries
iommu/vt-d: Remove domain_update_iommu_snooping()
iommu/vt-d: Check domain force_snooping against attached devices
iommu/vt-d: Block force-snoop domain attaching if no SC support
iommu/vt-d: Size Page Request Queue to avoid overflow condition
iommu/vt-d: Fold dmar_insert_one_dev_info() into its caller
iommu/vt-d: Change return type of dmar_insert_one_dev_info()
iommu/vt-d: Remove unneeded validity check on dev
iommu/dma: Explicitly sort PCI DMA windows
iommu/dma: Fix iova map result check bug
iommu/mediatek: Fix NULL pointer dereference when printing dev_name
iommu: iommu_group_claim_dma_owner() must always assign a domain
iommu/arm-smmu: Force identity domains for legacy binding
iommu/arm-smmu: Support Tegra234 SMMU
dt-bindings: arm-smmu: Add compatible for Tegra234 SOC
dt-bindings: arm-smmu: Document nvidia,memory-controller property
iommu/arm-smmu-qcom: Add SC8280XP support
dt-bindings: arm-smmu: Add compatible for Qualcomm SC8280XP
...
|
|
Calling pci_set_power_state() to put the given device into D0 in
pci_pm_thaw_noirq() may cause it to restore the device's BARs, which is
redundant before calling pci_restore_state(), so replace it with a direct
pci_power_up() call followed by pci_update_current_state() if it returns a
nonzero value, in analogy with pci_pm_default_resume_early().
Avoid code duplication by introducing a wrapper function to contain the
repeating pattern and calling it in both places.
Link: https://lore.kernel.org/r/3639079.MHq7AAxBmi@kreacher
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The runtime_d3cold flag is not needed any more, so drop it.
Link: https://lore.kernel.org/r/8077784.T7Z3S40VBb@kreacher
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Calling pci_resume_bus() on the secondary bus from pci_power_up() as it is
done now is questionable, because it depends on the mandatory bridge
power-up delays that are only covered by the PCI bus type PM callbacks.
For this reason, move the subordinate bus resume to those callbacks too and
use the observation that if a bridge is being powered-up during resume from
system-wide suspend, it may be still desirable to runtime-resume its
subordinate bus after completing the system-wide transition (in case the
resume of the devices on that bus is skipped during it).
Link: https://lore.kernel.org/r/3190097.aeNJFYEL58@kreacher
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Currently, endpoint devices may not be powered up entirely during runtime
resume that follows a D3hot -> D0 transition of the parent bridge.
Namely, even if the power state of an endpoint device, as indicated by its
PCI_PM_CTRL register, is D0 after powering up its parent bridge, it may be
still necessary to bring its ACPI companion into D0 and that should be done
before accessing it. However, the current code assumes that reading the
PCI_PM_CTRL register is sufficient to establish the endpoint device's power
state, which may lead to problems.
Address that by forcing a power-up of all PCI devices, including the
platform firmware part of it, during runtime resume.
Link: https://lore.kernel.org/linux-pm/11967527.O9o76ZdvQC@kreacher
Fixes: 5775b843a619 ("PCI: Restore config space on runtime resume despite being unbound")
Link: https://lore.kernel.org/r/2652115.mvXUDI8C0e@kreacher
Reported-by: Abhishek Sahu <abhsahu@nvidia.com>
Tested-by: Abhishek Sahu <abhsahu@nvidia.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
pci_restore_standard_config() was defined under CONFIG_PM but called only
by pci_pm_resume() (defined under CONFIG_SUSPEND) and pci_pm_restore()
(defined under CONFIG_HIBERNATE_CALLBACKS). A configuration with only
CONFIG_PM leads to a warning:
drivers/pci/pci-driver.c:533:12: error: ‘pci_restore_standard_config’ defined but not used [-Werror=unused-function]
CONFIG_PM_SLEEP depends on CONFIG_SUSPEND and CONFIG_HIBERNATE_CALLBACKS,
so define pci_restore_standard_config() under that instead.
Link: https://lore.kernel.org/r/20220420141135.444820-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The devices on platform/amba/fsl-mc/PCI buses could be bound to drivers
with the device DMA managed by kernel drivers or user-space applications.
Unfortunately, multiple devices may be placed in the same IOMMU group
because they cannot be isolated from each other. The DMA on these devices
must either be entirely under kernel control or userspace control, never
a mixture. Otherwise the driver integrity is not guaranteed because they
could access each other through the peer-to-peer accesses which by-pass
the IOMMU protection.
This checks and sets the default DMA mode during driver binding, and
cleanups during driver unbinding. In the default mode, the device DMA is
managed by the device driver which handles DMA operations through the
kernel DMA APIs (see Documentation/core-api/dma-api.rst).
For cases where the devices are assigned for userspace control through the
userspace driver framework(i.e. VFIO), the drivers(for example, vfio_pci/
vfio_platfrom etc.) may set a new flag (driver_managed_dma) to skip this
default setting in the assumption that the drivers know what they are
doing with the device DMA.
Calling iommu_device_use_default_domain() before {of,acpi}_dma_configure
is currently a problem. As things stand, the IOMMU driver ignored the
initial iommu_probe_device() call when the device was added, since at
that point it had no fwspec yet. In this situation,
{of,acpi}_iommu_configure() are retriggering iommu_probe_device() after
the IOMMU driver has seen the firmware data via .of_xlate to learn that
it actually responsible for the given device. As the result, before
that gets fixed, iommu_use_default_domain() goes at the end, and calls
arch_teardown_dma_ops() if it fails.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Stuart Yoder <stuyoder@gmail.com>
Cc: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Link: https://lore.kernel.org/r/20220418005000.897664-5-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler updates from Ingo Molnar:
- Cleanups for SCHED_DEADLINE
- Tracing updates/fixes
- CPU Accounting fixes
- First wave of changes to optimize the overhead of the scheduler
build, from the fast-headers tree - including placeholder *_api.h
headers for later header split-ups.
- Preempt-dynamic using static_branch() for ARM64
- Isolation housekeeping mask rework; preperatory for further changes
- NUMA-balancing: deal with CPU-less nodes
- NUMA-balancing: tune systems that have multiple LLC cache domains per
node (eg. AMD)
- Updates to RSEQ UAPI in preparation for glibc usage
- Lots of RSEQ/selftests, for same
- Add Suren as PSI co-maintainer
* tag 'sched-core-2022-03-22' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (81 commits)
sched/headers: ARM needs asm/paravirt_api_clock.h too
sched/numa: Fix boot crash on arm64 systems
headers/prep: Fix header to build standalone: <linux/psi.h>
sched/headers: Only include <linux/entry-common.h> when CONFIG_GENERIC_ENTRY=y
cgroup: Fix suspicious rcu_dereference_check() usage warning
sched/preempt: Tell about PREEMPT_DYNAMIC on kernel headers
sched/topology: Remove redundant variable and fix incorrect type in build_sched_domains
sched/deadline,rt: Remove unused parameter from pick_next_[rt|dl]_entity()
sched/deadline,rt: Remove unused functions for !CONFIG_SMP
sched/deadline: Use __node_2_[pdl|dle]() and rb_first_cached() consistently
sched/deadline: Merge dl_task_can_attach() and dl_cpu_busy()
sched/deadline: Move bandwidth mgmt and reclaim functions into sched class source file
sched/deadline: Remove unused def_dl_bandwidth
sched/tracing: Report TASK_RTLOCK_WAIT tasks as TASK_UNINTERRUPTIBLE
sched/tracing: Don't re-read p->state when emitting sched_switch event
sched/rt: Plug rt_mutex_setprio() vs push_rt_task() race
sched/cpuacct: Remove redundant RCU read lock
sched/cpuacct: Optimize away RCU read lock
sched/cpuacct: Fix charge percpu cpuusage
sched/headers: Reorganize, clean up and optimize kernel/sched/sched.h dependencies
...
|
|
Currently, suspend_report_result() prints only function information.
If any driver uses a common PM function, nobody knows who exactly
called the failing function.
A device pinter is needed to recognize the failing device.
For example:
PM: dpm_run_callback(): pnp_bus_suspend+0x0/0x10 returns 0
PM: dpm_run_callback(): pci_pm_suspend+0x0/0x150 returns 0
become after the change:
serial 00:05: PM: dpm_run_callback(): pnp_bus_suspend+0x0/0x10 returns 0
pci 0000:00:01.3: PM: dpm_run_callback(): pci_pm_suspend+0x0/0x150 returns 0
Signed-off-by: Youngjin Jang <yj84.jang@samsung.com>
[ rjw: Changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Refer to housekeeping APIs using single feature types instead of flags.
This prevents from passing multiple isolation features at once to
housekeeping interfaces, which soon won't be possible anymore as each
isolation features will have their own cpumask.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Juri Lelli <juri.lelli@redhat.com>
Reviewed-by: Phil Auld <pauld@redhat.com>
Link: https://lore.kernel.org/r/20220207155910.527133-5-frederic@kernel.org
|
|
To prepare for supporting each feature of the housekeeping cpumask
toward cpuset, prepare each of the HK_FLAG_* entries to move to their
own cpumask with enforcing to fetch them individually. The new
constraint is that multiple HK_FLAG_* entries can't be mixed together
anymore in a single call to housekeeping cpumask().
This will later allow, for example, to runtime modify the cpulist passed
through "isolcpus=", "nohz_full=" and "rcu_nocbs=" kernel boot
parameters.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Juri Lelli <juri.lelli@redhat.com>
Reviewed-by: Phil Auld <pauld@redhat.com>
Link: https://lore.kernel.org/r/20220207155910.527133-2-frederic@kernel.org
|
|
This reverts commit 2a4d9408c9e8b6f6fc150c66f3fef755c9e20d4a.
Robert reported a NULL pointer dereference caused by the PCI core
(local_pci_probe()) calling the i2c_designware_pci driver's
.runtime_resume() method before the .probe() method. i2c_dw_pci_resume()
depends on initialization done by i2c_dw_pci_probe().
Prior to 2a4d9408c9e8 ("PCI: Use to_pci_driver() instead of
pci_dev->driver"), pci_pm_runtime_resume() avoided calling the
.runtime_resume() method because pci_dev->driver had not been set yet.
2a4d9408c9e8 and b5f9c644eb1b ("PCI: Remove struct pci_dev->driver"),
removed pci_dev->driver, replacing it by device->driver, which *has* been
set by this time, so pci_pm_runtime_resume() called the .runtime_resume()
method when it previously had not.
Fixes: 2a4d9408c9e8 ("PCI: Use to_pci_driver() instead of pci_dev->driver")
Link: https://lore.kernel.org/linux-i2c/CAP145pgdrdiMAT7=-iB1DMgA7t_bMqTcJL4N0=6u8kNY3EU0dw@mail.gmail.com/
Reported-by: Robert Święcki <robert@swiecki.net>
Tested-by: Robert Święcki <robert@swiecki.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
This reverts commit b5f9c644eb1baafcd349ad134e2110773f8d0a38.
Revert b5f9c644eb1b ("PCI: Remove struct pci_dev->driver"), which is needed
to revert 2a4d9408c9e8 ("PCI: Use to_pci_driver() instead of
pci_dev->driver").
2a4d9408c9e8 caused a NULL pointer dereference reported by Robert Święcki.
Details in the revert of that commit.
Fixes: 2a4d9408c9e8 ("PCI: Use to_pci_driver() instead of pci_dev->driver")
Link: https://lore.kernel.org/linux-i2c/CAP145pgdrdiMAT7=-iB1DMgA7t_bMqTcJL4N0=6u8kNY3EU0dw@mail.gmail.com/
Reported-by: Robert Święcki <robert@swiecki.net>
Tested-by: Robert Święcki <robert@swiecki.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
- Tidy setup-irq.c comments (Pranay Sanghai)
- Fix misspellings (Krzysztof Wilczyński)
- Fix sprintf(), sscanf() format mismatches (Krzysztof Wilczyński)
- Tidy cpqphp code formatting (Krzysztof Wilczyński)
- Remove unused pci_pool wrappers, which have been replaced by dma_pool
(Cai Huoqing)
- Remove a redundant initialization in __pci_reset_function_locked() (Colin
Ian King)
- Use 'unsigned int' instead of 'unsigned' (Krzysztof Wilczyński)
- Update PCI subsystem information in MAINTAINERS (Krzysztof Wilczyński)
- Include generic <linux/> headers instead of <asm/> for cpqphp and vmd
(Krzysztof Wilczyński)
* pci/misc:
PCI: vmd: Drop redundant includes of <asm/device.h>, <asm/msi.h>
PCI: cpqphp: Use <linux/io.h> instead of <asm/io.h>
MAINTAINERS: Update PCI subsystem information
PCI: Prefer 'unsigned int' over bare 'unsigned'
PCI: Remove redundant 'rc' initialization
PCI: Remove unused pci_pool wrappers
PCI: cpqphp: Format if-statement code block correctly
PCI: Use unsigned to match sscanf("%x") in pci_dev_str_match_path()
PCI: hv: Remove unnecessary use of %hx
PCI: Correct misspelled and remove duplicated words
PCI: Tidy comments
|
|
- Ignore Link Down/Up caused by error-induced Hot Reset so endpoint driver
can remain bound to device during error recovery (Lukas Wunner)
- Remove unused resume err_handler (Lukas Wunner)
- Remove unused pcie_port_bus_{,un}register() declarations (Lukas Wunner)
- Skip compiling err.c when CONFIG_PCIEAER not set (Lukas Wunner)
* pci/hotplug:
PCI/ERR: Reduce compile time for CONFIG_PCIEAER=n
PCI/portdrv: Remove unused pcie_port_bus_{,un}register() declarations
PCI/portdrv: Remove unused resume err_handler
PCI: pciehp: Ignore Link Down/Up caused by error-induced Hot Reset
PCI/portdrv: Rename pm_iter() to pcie_port_device_iter()
|
|
There are no remaining uses of the struct pci_dev->driver pointer, so
remove it.
Link: https://lore.kernel.org/r/20211004125935.2300113-12-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Struct pci_driver contains a struct device_driver, so for PCI devices, it's
easy to convert a device_driver * to a pci_driver * with to_pci_driver().
The device_driver * is in struct device, so we don't need to also keep
track of the pci_driver * in struct pci_dev.
Replace pci_dev->driver with to_pci_driver(). This is a step toward
removing pci_dev->driver.
[bhelgaas: split to separate patch]
Link: https://lore.kernel.org/r/20211004125935.2300113-11-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The sole non-static function in err.c, pcie_do_recovery(), is only
called from:
* aer.c (if CONFIG_PCIEAER=y)
* dpc.c (if CONFIG_PCIE_DPC=y, which depends on CONFIG_PCIEAER)
* edr.c (if CONFIG_PCIE_EDR=y, which depends on CONFIG_PCIE_DPC)
Thus, err.c need not be compiled if CONFIG_PCIEAER=n.
Also, pci_uevent_ers() and pcie_clear_device_status(), which are called
from err.c, can be #ifdef'ed away unless CONFIG_PCIEAER=y.
Since x86_64_defconfig doesn't enable CONFIG_PCIEAER, this change may
slightly reduce compile time for anyone doing a test build with that
config.
Link: https://lore.kernel.org/r/98f9041151268c1c035ab64cca320ad86803f64a.1627638184.git.lukas@wunner.de
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
When the device core calls the .probe() callback for a device, the device
is never bound, so pci_dev->driver is always NULL.
Remove the unnecessary test of !pci_dev->driver.
Link: https://lore.kernel.org/r/20211004125935.2300113-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
|
|
When the driver core calls pci_device_remove(), there is a driver bound
to the device, so pci_dev->driver is never NULL.
Remove the unnecessary test of pci_dev->driver.
Link: https://lore.kernel.org/r/20211004125935.2300113-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
|
|
Correct a number of misspelled words and remove any words that were
duplicated in the PCI tree. No change to functionality intended.
Link: https://lore.kernel.org/r/20211006233827.147328-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Pull VFIO updates from Alex Williamson:
- Fix dma-valid return WAITED implementation (Anthony Yznaga)
- SPDX license cleanups (Cai Huoqing)
- Split vfio-pci-core from vfio-pci and enhance PCI driver matching to
support future vendor provided vfio-pci variants (Yishai Hadas, Max
Gurtovoy, Jason Gunthorpe)
- Replace duplicated reflck with core support for managing first open,
last close, and device sets (Jason Gunthorpe, Max Gurtovoy, Yishai
Hadas)
- Fix non-modular mdev support and don't nag about request callback
support (Christoph Hellwig)
- Add semaphore to protect instruction intercept handler and replace
open-coded locks in vfio-ap driver (Tony Krowiak)
- Convert vfio-ap to vfio_register_group_dev() API (Jason Gunthorpe)
* tag 'vfio-v5.15-rc1' of git://github.com/awilliam/linux-vfio: (37 commits)
vfio/pci: Introduce vfio_pci_core.ko
vfio: Use kconfig if XX/endif blocks instead of repeating 'depends on'
vfio: Use select for eventfd
PCI / VFIO: Add 'override_only' support for VFIO PCI sub system
PCI: Add 'override_only' field to struct pci_device_id
vfio/pci: Move module parameters to vfio_pci.c
vfio/pci: Move igd initialization to vfio_pci.c
vfio/pci: Split the pci_driver code out of vfio_pci_core.c
vfio/pci: Include vfio header in vfio_pci_core.h
vfio/pci: Rename ops functions to fit core namings
vfio/pci: Rename vfio_pci_device to vfio_pci_core_device
vfio/pci: Rename vfio_pci_private.h to vfio_pci_core.h
vfio/pci: Rename vfio_pci.c to vfio_pci_core.c
vfio/ap_ops: Convert to use vfio_register_group_dev()
s390/vfio-ap: replace open coded locks for VFIO_GROUP_NOTIFY_SET_KVM notification
s390/vfio-ap: r/w lock for PQAP interception handler function pointer
vfio/type1: Fix vfio_find_dma_valid return
vfio-pci/zdev: Remove repeated verbose license text
vfio: platform: reset: Convert to SPDX identifier
vfio: Remove struct vfio_device_ops open/release
...
|
|
Add 'override_only' field to struct pci_device_id to be used as part of
pci_match_device().
When set, a driver only matches the entry when dev->driver_override is
set to that driver.
In addition, add a helper macro named 'PCI_DEVICE_DRIVER_OVERRIDE' to
enable setting some data on it.
Next patch from this series will use the above functionality.
Signed-off-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Yishai Hadas <yishaih@nvidia.com>
Link: https://lore.kernel.org/r/20210826103912.128972-10-yishaih@nvidia.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
The driver core ignores the return value of this callback because there
is only little it can do when a device disappears.
This is the final bit of a long lasting cleanup quest where several
buses were converted to also return void from their remove callback.
Additionally some resource leaks were fixed that were caused by drivers
returning an error code in the expectation that the driver won't go
away.
With struct bus_type::remove returning void it's prevented that newly
implemented buses return an ignored error code and so don't anticipate
wrong expectations for driver authors.
Reviewed-by: Tom Rix <trix@redhat.com> (For fpga)
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Cornelia Huck <cohuck@redhat.com> (For drivers/s390 and drivers/vfio)
Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> (For ARM, Amba and related parts)
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Chen-Yu Tsai <wens@csie.org> (for sunxi-rsb)
Acked-by: Pali Rohár <pali@kernel.org>
Acked-by: Mauro Carvalho Chehab <mchehab@kernel.org> (for media)
Acked-by: Hans de Goede <hdegoede@redhat.com> (For drivers/platform)
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Acked-by: Juergen Gross <jgross@suse.com> (For xen)
Acked-by: Lee Jones <lee.jones@linaro.org> (For mfd)
Acked-by: Johannes Thumshirn <jth@kernel.org> (For mcb)
Acked-by: Johan Hovold <johan@kernel.org>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> (For slimbus)
Acked-by: Kirti Wankhede <kwankhede@nvidia.com> (For vfio)
Acked-by: Maximilian Luz <luzmaximilian@gmail.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> (For ulpi and typec)
Acked-by: Samuel Iglesias Gonsálvez <siglesias@igalia.com> (For ipack)
Acked-by: Geoff Levand <geoff@infradead.org> (For ps3)
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com> (For thunderbolt)
Acked-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> (For intel_th)
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net> (For pcmcia)
Acked-by: Rafael J. Wysocki <rafael@kernel.org> (For ACPI)
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org> (rpmsg and apr)
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> (For intel-ish-hid)
Acked-by: Dan Williams <dan.j.williams@intel.com> (For CXL, DAX, and NVDIMM)
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com> (For isa)
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (For firewire)
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> (For hid)
Acked-by: Thorsten Scherer <t.scherer@eckelmann.de> (For siox)
Acked-by: Sven Van Asbroeck <TheSven73@gmail.com> (For anybuss)
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> (For MMC)
Acked-by: Wolfram Sang <wsa@kernel.org> # for I2C
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Finn Thain <fthain@linux-m68k.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20210713193522.1770306-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This helps converting PCI drivers sysfs attributes to static.
Analogous to' commit b71b283e3d6d ("USB: add support for dev_groups to
struct usb_driver")'
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210512142648.666476-8-andrey.grodzovsky@amd.com
|
|
- Update kernel-doc to match function prototypes (Mauro Carvalho Chehab)
- Bounds-check "pci=resource_alignment=" requests (Bjorn Helgaas)
- Fix integer overflow in "pci=resource_alignment=" requests (Colin Ian
King)
- Remove unused HAVE_PCI_SET_MWI definition (Heiner Kallweit)
- Reduce pci_set_cacheline_size() message to debug level (Heiner Kallweit)
* pci/misc:
PCI: Reduce pci_set_cacheline_size() message to debug level
PCI: Remove unused HAVE_PCI_SET_MWI
PCI: Fix overflow in command-line resource alignment requests
PCI: Bounds-check command-line resource alignment requests
PCI: Fix kernel-doc markup
# Conflicts:
# drivers/pci/pci-driver.c
|
|
Update kernel-doc so the names in the doc match the prototypes.
Link: https://lore.kernel.org/r/f19caf7a68f8365c8b573a42b4ac89ec21925c73.1603469755.git.mchehab+huawei@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
When a device ID is written to /sys/bus/pci/drivers/.../new_id, we
previously only checked the driver's static ID table for duplicates.
Writing the same ID several times added it to the dynamic IDs list several
times.
This doesn't cause user-visible broken behavior, but remove_id_store() only
removes one of the duplicate IDs, so if we add an ID several times, we
would have to remove it the same number of times before it's completely
gone.
Fix it by calling pci_match_device(), which checks both dynamic and static
IDs to avoid inserting duplicate IDs in dynamic IDs list.
After fix, attempts to add an ID more than once cause an error:
# echo "1af4 1041" > /sys/bus/pci/drivers/vfio-pci/new_id
# echo "1af4 1041" > /sys/bus/pci/drivers/vfio-pci/new_id
bash: echo: write error: File exists
Link: https://lore.kernel.org/r/20201117054409.3428-3-zhenzhong.duan@gmail.com
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Move pci_match_device() and its dependencies (pci_match_id() and
pci_device_id_any) ahead of new_id_store().
This is preparation work for calling pci_match_device() in new_id_store().
No functional changes.
[bhelgaas: update function comments]
Link: https://lore.kernel.org/r/20201117054409.3428-2-zhenzhong.duan@gmail.com
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Print IRQ number used by PCIe Link Bandwidth Notification (Dongdong
Liu)
- Add schedule point in pci_read_config() to reduce max latency
(Jiang Biao)
- Add Kconfig options for MPS/MRRS strategy (Jim Quinlan)
Resource management:
- Fix pci_iounmap() memory leak when !CONFIG_GENERIC_IOMAP (Lorenzo
Pieralisi)
PCIe native device hotplug:
- Reduce noisiness on hot removal (Lukas Wunner)
Power management:
- Revert "PCI/PM: Apply D2 delay as milliseconds, not microseconds"
that was done on the basis of spec typo (Bjorn Helgaas)
- Rename pci_dev.d3_delay to d3hot_delay to remove D3hot/D3cold
ambiguity (Krzysztof Wilczyński)
- Remove unused pcibios_pm_ops (Vaibhav Gupta)
IOMMU:
- Enable Translation Blocking for external devices to harden against
DMA attacks (Rajat Jain)
Error handling:
- Add an ACPI APEI notifier chain for vendor CPER records to enable
device-specific error handling (Shiju Jose)
ASPM:
- Remove struct aspm_register_info to simplify code (Saheed O.
Bolarinwa)
Amlogic Meson PCIe controller driver:
- Build as module by default (Kevin Hilman)
Ampere Altra PCIe controller driver:
- Add MCFG quirk to work around non-standard ECAM implementation
(Tuan Phan)
Broadcom iProc PCIe controller driver:
- Set affinity mask on MSI interrupts (Mark Tomlinson)
Broadcom STB PCIe controller driver:
- Make PCIE_BRCMSTB depend on ARCH_BRCMSTB (Jim Quinlan)
- Add DT bindings for more Brcmstb chips (Jim Quinlan)
- Add bcm7278 register info (Jim Quinlan)
- Add bcm7278 PERST# support (Jim Quinlan)
- Add suspend and resume pm_ops (Jim Quinlan)
- Add control of rescal reset (Jim Quinlan)
- Set additional internal memory DMA viewport sizes (Jim Quinlan)
- Accommodate MSI for older chips (Jim Quinlan)
- Set bus max burst size by chip type (Jim Quinlan)
- Add support for bcm7211, bcm7216, bcm7445, bcm7278 (Jim Quinlan)
Freescale i.MX6 PCIe controller driver:
- Use dev_err_probe() to reduce redundant messages (Anson Huang)
Freescale Layerscape PCIe controller driver:
- Enforce 4K DMA buffer alignment in endpoint test (Hou Zhiqiang)
- Add DT compatible strings for ls1088a, ls2088a (Xiaowei Bao)
- Add endpoint support for ls1088a, ls2088a (Xiaowei Bao)
- Add endpoint test support for lS1088a (Xiaowei Bao)
- Add MSI-X support for ls1088a (Xiaowei Bao)
HiSilicon HIP PCIe controller driver:
- Handle HIP-specific errors via ACPI APEI (Yicong Yang)
HiSilicon Kirin PCIe controller driver:
- Return -EPROBE_DEFER if the GPIO isn't ready (Bean Huo)
Intel VMD host bridge driver:
- Factor out physical offset, bus offset, IRQ domain, IRQ allocation
(Jon Derrick)
- Use generic PCI PM correctly (Jon Derrick)
Marvell Aardvark PCIe controller driver:
- Fix compilation on s390 (Pali Rohár)
- Implement driver 'remove' function and allow to build it as module
(Pali Rohár)
- Move PCIe reset card code to advk_pcie_train_link() (Pali Rohár)
- Convert mvebu a3700 internal SMCC firmware return codes to errno
(Pali Rohár)
- Fix initialization with old Marvell's Arm Trusted Firmware (Pali
Rohár)
Microsoft Hyper-V host bridge driver:
- Fix hibernation in case interrupts are not re-created (Dexuan Cui)
NVIDIA Tegra PCIe controller driver:
- Stop checking return value of debugfs_create() functions (Greg
Kroah-Hartman)
- Convert to use DEFINE_SEQ_ATTRIBUTE macro (Liu Shixin)
Qualcomm PCIe controller driver:
- Reset PCIe to work around Qsdk U-Boot issue (Ansuel Smith)
Renesas R-Car PCIe controller driver:
- Add DT documentation for r8a774a1, r8a774b1, r8a774e1 endpoints
(Lad Prabhakar)
- Add RZ/G2M, RZ/G2N, RZ/G2H IDs to endpoint test (Lad Prabhakar)
- Add DT support for r8a7742 (Lad Prabhakar)
Socionext UniPhier Pro5 controller driver:
- Add DT descriptions of iATU register (host and endpoint) (Kunihiko
Hayashi)
Synopsys DesignWare PCIe controller driver:
- Add link up check in dw_child_pcie_ops.map_bus() (racy, but seems
unavoidable) (Hou Zhiqiang)
- Fix endpoint Header Type check so multi-function devices work (Hou
Zhiqiang)
- Skip PCIE_MSI_INTR0* programming if MSI is disabled (Jisheng Zhang)
- Stop leaking MSI page in suspend/resume (Jisheng Zhang)
- Add common iATU register support instead of keystone-specific code
(Kunihiko Hayashi)
- Major config space access and other cleanups in dwc core and
drivers that use it (al, exynos, histb, imx6, intel-gw, keystone,
kirin, meson, qcom, tegra) (Rob Herring)
- Add multiple PFs support for endpoint (Xiaowei Bao)
- Add MSI-X doorbell mode in endpoint mode (Xiaowei Bao)
Miscellaneous:
- Use fallthrough pseudo-keyword (Gustavo A. R. Silva)
- Fix "0 used as NULL pointer" warnings (Gustavo Pimentel)
- Fix "cast truncates bits from constant value" warnings (Gustavo
Pimentel)
- Remove redundant zeroing for sg_init_table() (Julia Lawall)
- Use scnprintf(), not snprintf(), in sysfs "show" functions
(Krzysztof Wilczyński)
- Remove unused assignments (Krzysztof Wilczyński)
- Fix "0 used as NULL pointer" warning (Krzysztof Wilczyński)
- Simplify bool comparisons (Krzysztof Wilczyński)
- Use for_each_child_of_node() and for_each_node_by_name() (Qinglang
Miao)
- Simplify return expressions (Qinglang Miao)"
* tag 'pci-v5.10-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (147 commits)
PCI: vmd: Update VMD PM to correctly use generic PCI PM
PCI: vmd: Create IRQ allocation helper
PCI: vmd: Create IRQ Domain configuration helper
PCI: vmd: Create bus offset configuration helper
PCI: vmd: Create physical offset helper
PCI: v3-semi: Remove unneeded break
PCI: dwc: Add link up check in dw_child_pcie_ops.map_bus()
PCI/ASPM: Remove struct pcie_link_state.l1ss
PCI/ASPM: Remove struct aspm_register_info.l1ss_cap
PCI/ASPM: Pass L1SS Capabilities value, not struct aspm_register_info
PCI/ASPM: Remove struct aspm_register_info.l1ss_ctl1
PCI/ASPM: Remove struct aspm_register_info.l1ss_ctl2 (unused)
PCI/ASPM: Remove struct aspm_register_info.l1ss_cap_ptr
PCI/ASPM: Remove struct aspm_register_info.latency_encoding
PCI/ASPM: Remove struct aspm_register_info.enabled
PCI/ASPM: Remove struct aspm_register_info.support
PCI/ASPM: Use 'parent' and 'child' for readability
PCI/ASPM: Move LTR path check to where it's used
PCI/ASPM: Move pci_clear_and_set_dword() earlier
PCI: dwc: Fix MSI page leakage in suspend/resume
...
|
|
Most of dma-debug.h is not required by anything outside of kernel/dma.
Move the four declarations needed by dma-mappin.h or dma-ops providers
into dma-mapping.h and dma-map-ops.h, and move the remainder of the
file to kernel/dma/debug.h.
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
The "struct dev_pm_ops pcibios_pm_ops", declared in include/linux/pci.h and
defined in drivers/pci/pci-driver.c, provided arch-specific hooks when a
PCI device was doing a hibernate transition.
394216275c7d ("s390: remove broken hibernate / power management support")
removed the last use of pcibios_pm_ops, so remove it completely.
[bhelgaas: drop unused "error"]
Link: https://lore.kernel.org/r/20200730194416.1029509-1-vaibhavgupta40@gmail.com
Reported-by: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|