| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
- Move IRQ register address computation inside macros (Kishon Vijay
Abraham I)
- Separate legacy IRQ and MSI configuration (Kishon Vijay Abraham I)
- Use hwirq, not virq, to get MSI IRQ number offset (Kishon Vijay Abraham
I)
- Squash ks_pcie_handle_msi_irq() into ks_pcie_msi_irq_handler() (Kishon
Vijay Abraham I)
- Add dwc support for platforms with custom MSI controllers (Kishon Vijay
Abraham I)
- Add keystone-specific MSI controller (Kishon Vijay Abraham I)
- Remove dwc host_ops previously used for keystone-specific MSI (Kishon
Vijay Abraham I)
- Skip dwc default MSI init if platform has custom MSI controller (Kishon
Vijay Abraham I)
- Implement .start_link() and .stop_link() for keystone endpoint support
(Kishon Vijay Abraham I)
- Add keystone "reg-names" DT binding (Kishon Vijay Abraham I)
- Squash ks_pcie_dw_host_init() into ks_pcie_add_pcie_port() (Kishon
Vijay Abraham I)
- Get keystone register resources from DT by name, not index (Kishon
Vijay Abraham I)
- Get DT resources in .probe() to prepare for endpoint support (Kishon
Vijay Abraham I)
- Add "ti,syscon-pcie-mode" DT property for PCIe mode configuration
(Kishon Vijay Abraham I)
- Explicitly set keystone to host mode (Kishon Vijay Abraham I)
- Document DT "atu" reg-names requirement for DesignWare core >= 4.80
(Kishon Vijay Abraham I)
- Enable dwc iATU unroll for endpoint mode as well as host mode (Kishon
Vijay Abraham I)
- Add dwc "version" to identify core >= 4.80 for ATU programming (Kishon
Vijay Abraham I)
- Don't build ARM32-specific keystone code on ARM64 (Kishon Vijay Abraham
I)
- Add DT binding for keystone PCIe RC in AM654 SoC (Kishon Vijay Abraham
I)
- Add keystone support for AM654 SoC PCIe RC (Kishon Vijay Abraham I)
- Reset keystone PHYs before enabling them (Kishon Vijay Abraham I)
- Make of_pci_get_max_link_speed() available to endpoint drivers as well
as host drivers (Kishon Vijay Abraham I)
- Add keystone support for DT "max-link-speed" property (Kishon Vijay
Abraham I)
- Add endpoint library support for BAR buffer alignment (Kishon Vijay
Abraham I)
- Make all dw_pcie_ep_ops structs const (Kishon Vijay Abraham I)
- Fix fencepost error in dw_pcie_ep_find_capability() (Kishon Vijay
Abraham I)
- Add dwc hooks for dbi/dbi2 that share the same address space (Kishon
Vijay Abraham I)
- Add keystone support for TI AM654x in endpoint mode (Kishon Vijay
Abraham I)
- Configure designware endpoints to advertise smallest resizable BAR
(1MB) (Kishon Vijay Abraham I)
- Align designware endpoint ATU windows for raising MSIs (Kishon Vijay
Abraham I)
- Add endpoint test support for TI AM654x (Kishon Vijay Abraham I)
- Fix endpoint test test_reg_bar issue (Kishon Vijay Abraham I)
* remotes/lorenzo/pci/keystone:
misc: pci_endpoint_test: Fix test_reg_bar to be updated in pci_endpoint_test
misc: pci_endpoint_test: Add support to test PCI EP in AM654x
PCI: designware-ep: Use aligned ATU window for raising MSI interrupts
PCI: designware-ep: Configure Resizable BAR cap to advertise the smallest size
PCI: keystone: Add support for PCIe EP in AM654x Platforms
dt-bindings: PCI: Add PCI EP DT binding documentation for AM654
PCI: dwc: Add callbacks for accessing dbi2 address space
PCI: dwc: Fix dw_pcie_ep_find_capability() to return correct capability offset
PCI: dwc: Add const qualifier to struct dw_pcie_ep_ops
PCI: endpoint: Add support to specify alignment for buffers allocated to BARs
PCI: keystone: Add support to set the max link speed from DT
PCI: OF: Allow of_pci_get_max_link_speed() to be used by PCI Endpoint drivers
PCI: keystone: Invoke phy_reset() API before enabling PHY
PCI: keystone: Add support for PCIe RC in AM654x Platforms
dt-bindings: PCI: Add PCI RC DT binding documentation for AM654
PCI: keystone: Prevent ARM32 specific code to be compiled for ARM64
PCI: dwc: Fix ATU identification for designware version >= 4.80
PCI: dwc: Enable iATU unroll for endpoint too
dt-bindings: PCI: Document "atu" reg-names
PCI: keystone: Explicitly set the PCIe mode
dt-bindings: PCI: Add dt-binding to configure PCIe mode
PCI: keystone: Move resources initialization to prepare for EP support
PCI: keystone: Use platform_get_resource_byname() to get memory resources
PCI: keystone: Perform host initialization in a single function
dt-bindings: PCI: keystone: Add "reg-names" binding information
PCI: keystone: Cleanup error_irq configuration
PCI: keystone: Add start_link()/stop_link() dw_pcie_ops
PCI: dwc: Remove default MSI initialization for platform specific MSI chips
PCI: dwc: Remove Keystone specific dw_pcie_host_ops
PCI: keystone: Use Keystone specific msi_irq_chip
PCI: dwc: Add support to use non default msi_irq_chip
PCI: keystone: Cleanup ks_pcie_msi_irq_handler()
PCI: keystone: Use hwirq to get the MSI IRQ number offset
PCI: keystone: Add separate functions for configuring MSI and legacy interrupt
PCI: keystone: Cleanup interrupt related macros
# Conflicts:
# drivers/pci/controller/dwc/pcie-designware.h
|
|
Both pcie-designware.c and pci-imx6.c contain custom definitions for
PHY debug registers R0/R1 and on top of that there's already a
definition for R0 in pcie-designware.h. Move all of the definitions to
pcie-designware.h. No functional change intended.
Signed-off-by: Andrey Smirnov <[email protected]>
Signed-off-by: Lorenzo Pieralisi <[email protected]>
Reviewed-by: Lucas Stach <[email protected]>
Cc: Lorenzo Pieralisi <[email protected]>
Cc: Bjorn Helgaas <[email protected]>
Cc: Chris Healy <[email protected]>
Cc: Lucas Stach <[email protected]>
Cc: [email protected]
Cc: [email protected]
|
|
Certain platforms like TI's AM654 do not have aseparate address space for
dbi2 instead they are accessed using the same address space as dbi
with some configuration bit set. In order to support such platforms,
add callbacks for accessing dbi2 address space.
Signed-off-by: Kishon Vijay Abraham I <[email protected]>
Signed-off-by: Lorenzo Pieralisi <[email protected]>
|
|
Synopsys designware version >= 4.80 uses a separate register space
for programming ATU. The current code identifies if there exists a
separate register space by accessing the register address of ATUs
in designware version < 4.80. Accessing this address results in
abort in the case of K2G.
Fix it here by adding "version" member to struct dw_pcie. This should be
set by platform specific drivers and designware core will use it to
identify if the platform has a separate ATU space. For platforms which
have not populated the version member, the old method of identification
will still be used.
Signed-off-by: Kishon Vijay Abraham I <[email protected]>
Signed-off-by: Lorenzo Pieralisi <[email protected]>
|
|
iatu_unroll_enabled flag is set only for Designware in host mode.
However iATU unroll can be applicable for endpoint mode too. Set
iatu_unroll_enabled flag in dw_pcie_setup() which is common for
both host mode and endpoint mode.
Signed-off-by: Kishon Vijay Abraham I <[email protected]>
Signed-off-by: Lorenzo Pieralisi <[email protected]>
|
|
Avoid using explicit left shifts and convert various definitions to
use BIT() instead. No functional change intended.
Signed-off-by: Andrey Smirnov <[email protected]>
[[email protected]: fixed PORT_LOGIC_SPEED_CHANGE redefinition]
Signed-off-by: Lorenzo Pieralisi <[email protected]>
Acked-by: Gustavo Pimentel <[email protected]>
Cc: Lorenzo Pieralisi <[email protected]>
Cc: Bjorn Helgaas <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Chris Healy <[email protected]>
Cc: Lucas Stach <[email protected]>
Cc: Leonard Crestez <[email protected]>
Cc: "A.s. Dong" <[email protected]>
Cc: Richard Zhu <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
|
|
Make the intent a bit more clear as well as get rid of explicit
arithmetic by using IS_ALIGNED() to determine if "addr" is aligned to
"size". No functional change intended.
Signed-off-by: Andrey Smirnov <[email protected]>
Signed-off-by: Lorenzo Pieralisi <[email protected]>
Acked-by: Gustavo Pimentel <[email protected]>
Cc: Lorenzo Pieralisi <[email protected]>
Cc: Bjorn Helgaas <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Chris Healy <[email protected]>
Cc: Lucas Stach <[email protected]>
Cc: Leonard Crestez <[email protected]>
Cc: "A.s. Dong" <[email protected]>
Cc: Richard Zhu <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
|
|
The DWC PCIe core contains various separate register spaces: DBI, DBI2,
ATU, DMA, etc. The relationship between the addresses of these register
spaces is entirely determined by the implementation of the IP block, not
by the IP block design itself. Hence, the DWC driver must not make
assumptions that one register space can be accessed at a fixed offset from
any other register space. To avoid such assumptions, introduce an
explicit/separate register pointer for the ATU register space. In
particular, the current assumption is not valid for NVIDIA's T194 SoC.
The ATU register space is only used on systems that require unrolled ATU
access. This property is detected at run-time for host controllers, and
when this is detected, this patch provides a default value for atu_base
that matches the previous assumption re: register layout. An alternative
would be to update all drivers for HW that requires unrolled access to
explicitly set atu_base. However, it's hard to tell which drivers would
require atu_base to be set. The unrolled property is not detected for
endpoint systems, and so any endpoint driver that requires unrolled access
must explicitly set the iatu_unroll_enabled flag (none do at present), and
so a check is added to require the driver to also set atu_base while at
it.
Signed-off-by: Stephen Warren <[email protected]>
Signed-off-by: Lorenzo Pieralisi <[email protected]>
Acked-by: Gustavo Pimentel <[email protected]>
Acked-by: Vidya Sagar <[email protected]>
|
|
When programming the inbound/outbound ATUs, we call usleep_range() after
each checking PCIE_ATU_ENABLE bit. Unfortunately, the ATU programming
can be executed in atomic context:
inbound ATU programming could be called through
pci_epc_write_header()
=>dw_pcie_ep_write_header()
=>dw_pcie_prog_inbound_atu()
outbound ATU programming could be called through
pci_bus_read_config_dword()
=>dw_pcie_rd_conf()
=>dw_pcie_prog_outbound_atu()
Fix this issue by calling mdelay() instead.
Fixes: f8aed6ec624f ("PCI: dwc: designware: Add EP mode support")
Fixes: d8bbeb39fbf3 ("PCI: designware: Wait for iATU enable")
Signed-off-by: Jisheng Zhang <[email protected]>
[[email protected]: commit log update]
Signed-off-by: Lorenzo Pieralisi <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
Acked-by: Gustavo Pimentel <[email protected]>
|
|
Native PCI drivers for root complex devices were originally all in
drivers/pci/host/. Some of these devices can also be operated in endpoint
mode. Drivers for endpoint mode didn't seem to fit in the "host"
directory, so we put both the root complex and endpoint drivers in
per-device directories, e.g., drivers/pci/dwc/, drivers/pci/cadence/, etc.
These per-device directories contain trivial Kconfig and Makefiles and
clutter drivers/pci/. Make a new drivers/pci/controllers/ directory and
collect all the device-specific drivers there.
No functional change intended.
Link: https://lkml.kernel.org/r/[email protected]
Signed-off-by: Shawn Lin <[email protected]>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <[email protected]>
|