| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Certain platforms like K2G reguires the outbound ATU window to be
aligned. The alignment size is already present in mem->page_size.
Use the alignment size present in mem->page_size to configure an
aligned ATU window. In order to raise an interrupt, CPU has to write
to address offset from the start of the window unlike before where
writes were always to the beginning of the ATU window.
Signed-off-by: Kishon Vijay Abraham I <[email protected]>
Signed-off-by: Lorenzo Pieralisi <[email protected]>
|
|
Configure the Resizable BAR capability to advertise the smallest size
(1MB) for a couple of reasons:
- Host side resource allocation of BAR fails for larger sizes
- Endpoint function driver does not allocate memory for all supported
sizes in the Resizable BAR capability.
If and when there is a usecase required to add more flexibility using
the Resizable BAR capability, this can be revisited.
Signed-off-by: Kishon Vijay Abraham I <[email protected]>
[[email protected]: updated commit log]
Signed-off-by: Lorenzo Pieralisi <[email protected]>
|
|
commit beb4641a787d ("PCI: dwc: Add MSI-X callbacks handler") while
adding MSI-X callback handler, introduced dw_pcie_ep_find_capability()
and __dw_pcie_ep_find_next_cap() for finding the MSI and MSIX capability.
However if MSI or MSIX capability is the last capability (i.e there are
no additional items in the capabilities list and the Next Capability
Pointer is set to '0'), __dw_pcie_ep_find_next_cap will return '0'
even though MSI or MSIX capability may be present because of
incorrect ordering of the "next_cap_ptr" check. Fix it.
Fixes: beb4641a787d ("PCI: dwc: Add MSI-X callbacks handler")
Signed-off-by: Kishon Vijay Abraham I <[email protected]>
Signed-off-by: Lorenzo Pieralisi <[email protected]>
|
|
iatu_unroll_enabled flag is set only for Designware in host mode.
However iATU unroll can be applicable for endpoint mode too. Set
iatu_unroll_enabled flag in dw_pcie_setup() which is common for
both host mode and endpoint mode.
Signed-off-by: Kishon Vijay Abraham I <[email protected]>
Signed-off-by: Lorenzo Pieralisi <[email protected]>
|
|
- Use memcpy_fromio()/memcpy_toio() instead of plain memcpy() in PCI
endpoint framework (Wen Yang)
- Add interface to discover supported endpoint features to replace a
bitfield that wasn't flexible enough (Kishon Vijay Abraham I)
- Implement the new supported-feature interface for designware-plat,
dra7xx, rockchip, cadence (Kishon Vijay Abraham I)
- Fix issues with 64-bit BAR in endpoints (Kishon Vijay Abraham I)
- Add layerscape endpoint mode support (Xiaowei Bao)
* remotes/lorenzo/pci/endpoint:
misc: pci_endpoint_test: Add the layerscape EP device support
PCI: layerscape: Add EP mode support
arm64: dts: Add the PCIE EP node in dts
dt-bindings: add DT binding for the layerscape PCIe controller with EP mode
PCI: endpoint: Remove features member in struct pci_epc
PCI: designware-plat: Remove setting epc->features in Designware plat EP driver
PCI: rockchip: Remove pci_epf_linkup() from Rockchip EP driver
PCI: cadence: Remove pci_epf_linkup() from Cadence EP driver
PCI: pci-epf-test: Use pci_epc_get_features() to get EPC features
PCI: pci-epf-test: Do not allocate next BARs memory if current BAR is 64Bit
PCI: pci-epf-test: Remove setting epf_bar flags in function driver
PCI: endpoint: Fix pci_epf_alloc_space() to set correct MEM TYPE flags
PCI: endpoint: Add helper to get first unreserved BAR
PCI: cadence: Populate ->get_features() cdns_pcie_epc_ops
PCI: rockchip: Populate ->get_features() dw_pcie_ep_ops
PCI: pci-dra7xx: Populate ->get_features() dw_pcie_ep_ops
PCI: designware-plat: Populate ->get_features() dw_pcie_ep_ops
PCI: dwc: Add ->get_features() callback function to dw_pcie_ep_ops
PCI: endpoint: Add new pci_epc_ops to get EPC features
PCI: endpoint: functions: Use memcpy_fromio()/memcpy_toio()
|
|
Each platform using Designware PCIe core can support different set of
endpoint features. Add a new callback function ->get_features() in
dw_pcie_ep_ops so that each platform using Designware PCIe core can
advertise its supported features to the endpoint function driver.
Tested-by: Gustavo Pimentel <[email protected]>
Signed-off-by: Kishon Vijay Abraham I <[email protected]>
Signed-off-by: Lorenzo Pieralisi <[email protected]>
|
|
Add debug error message when MSI-X entry control mask bit is set, to help
debug the reason why a MSI-X interrupt is not being triggered.
Signed-off-by: Gustavo Pimentel <[email protected]>
Signed-off-by: Lorenzo Pieralisi <[email protected]>
Cc: Jingoo Han <[email protected]>
Cc: Bjorn Helgaas <[email protected]>
Cc: Joao Pinto <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- Remove unused lists from ASPM pcie_link_state (Frederick Lawler)
- Fix Broadcom CNB20LE host bridge unintended sign extension (Colin Ian
King)
- Expand Kconfig "PF" acronyms (Randy Dunlap)
- Update MAINTAINERS for arch/x86/kernel/early-quirks.c (Bjorn Helgaas)
- Add missing include to drivers/pci.h (Alexandru Gagniuc)
- Override Synopsys USB 3.x HAPS device class so dwc3-haps can claim it
instead of xhci (Thinh Nguyen)
- Clean up P2PDMA documentation (Randy Dunlap)
- Allow runtime PM even if driver doesn't supply callbacks (Jarkko
Nikula)
- Remove status check after submitting Switchtec MRPC Firmware Download
commands to avoid Completion Timeouts (Kelvin Cao)
- Set Switchtec coherent DMA mask to allow 64-bit DMA (Boris Glimcher)
- Fix Switchtec SWITCHTEC_IOCTL_EVENT_IDX_ALL flag overwrite issue
(Joey Zhang)
- Enable write combining for Switchtec MRPC Input buffers (Kelvin Cao)
- Add Switchtec MRPC DMA mode support (Wesley Sheng)
- Skip VF scanning on powerpc, which does this in firmware (Sebastian
Ott)
- Add Amlogic Meson PCIe controller driver and DT bindings (Yue Wang)
- Constify histb dw_pcie_host_ops structure (Julia Lawall)
- Support multiple power domains for imx6 (Leonard Crestez)
- Constify layerscape driver data (Stefan Agner)
- Update imx6 Kconfig to allow imx6 PCIe in imx7 kernel (Trent Piepho)
- Support armada8k GPIO reset (Baruch Siach)
- Support suspend/resume support on imx6 (Leonard Crestez)
- Don't hard-code DesignWare DBI/ATU offst (Stephen Warren)
- Skip i.MX6 PHY setup on i.MX7D (Andrey Smirnov)
- Remove Jianguo Sun from HiSilicon STB maintainers (Lorenzo Pieralisi)
- Mask DesignWare interrupts instead of disabling them to avoid lost
interrupts (Marc Zyngier)
- Add locking when acking DesignWare interrupts (Marc Zyngier)
- Ack DesignWare interrupts in the proper callbacks (Marc Zyngier)
- Use devm resource parser in mediatek (Honghui Zhang)
- Remove unused mediatek "num-lanes" DT property (Honghui Zhang)
- Add UniPhier PCIe controller driver and DT bindings (Kunihiko
Hayashi)
- Enable MSI for imx6 downstream components (Richard Zhu)
* tag 'pci-v4.21-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (40 commits)
PCI: imx: Enable MSI from downstream components
s390/pci: skip VF scanning
PCI/IOV: Add flag so platforms can skip VF scanning
PCI/IOV: Factor out sriov_add_vfs()
PCI: uniphier: Add UniPhier PCIe host controller support
dt-bindings: PCI: Add UniPhier PCIe host controller description
PCI: amlogic: Add the Amlogic Meson PCIe controller driver
dt-bindings: PCI: meson: add DT bindings for Amlogic Meson PCIe controller
arm64: dts: mt7622: Remove un-used property for PCIe
arm: dts: mt7623: Remove un-used property for PCIe
dt-bindings: PCI: MediaTek: Remove un-used property
PCI: mediatek: Remove un-used variant in struct mtk_pcie_port
MAINTAINERS: Remove Jianguo Sun from HiSilicon STB DWC entry
PCI: dwc: Don't hard-code DBI/ATU offset
PCI: imx: Add imx6sx suspend/resume support
PCI: armada8k: Add support for gpio controlled reset signal
PCI: dwc: Adjust Kconfig to allow IMX6 PCIe host on IMX7
PCI: dwc: layerscape: Constify driver data
PCI: imx: Add multi-pd support
PCI: Override Synopsys USB 3.x HAPS device class
...
|
|
The DWC PCIe core contains various separate register spaces: DBI, DBI2,
ATU, DMA, etc. The relationship between the addresses of these register
spaces is entirely determined by the implementation of the IP block, not
by the IP block design itself. Hence, the DWC driver must not make
assumptions that one register space can be accessed at a fixed offset from
any other register space. To avoid such assumptions, introduce an
explicit/separate register pointer for the ATU register space. In
particular, the current assumption is not valid for NVIDIA's T194 SoC.
The ATU register space is only used on systems that require unrolled ATU
access. This property is detected at run-time for host controllers, and
when this is detected, this patch provides a default value for atu_base
that matches the previous assumption re: register layout. An alternative
would be to update all drivers for HW that requires unrolled access to
explicitly set atu_base. However, it's hard to tell which drivers would
require atu_base to be set. The unrolled property is not detected for
endpoint systems, and so any endpoint driver that requires unrolled access
must explicitly set the iatu_unroll_enabled flag (none do at present), and
so a check is added to require the driver to also set atu_base while at
it.
Signed-off-by: Stephen Warren <[email protected]>
Signed-off-by: Lorenzo Pieralisi <[email protected]>
Acked-by: Gustavo Pimentel <[email protected]>
Acked-by: Vidya Sagar <[email protected]>
|
|
Fix an error caused by 3-bit right rotation on offset address
calculation of MSI-X table in dw_pcie_ep_raise_msix_irq().
The initial testing code was setting by default the offset address of
MSI-X table to zero, so that even with a 3-bit right rotation the
computed result would still be zero and valid, therefore this bug went
unnoticed.
Fixes: beb4641a787d ("PCI: dwc: Add MSI-X callbacks handler")
Signed-off-by: Gustavo Pimentel <[email protected]>
[[email protected]: updated commit log]
Signed-off-by: Lorenzo Pieralisi <[email protected]>
Cc: [email protected]
|
|
Currently DesignWare IP does not handle legacy interrupts.
Add a legacy interrupt callback handler.
Signed-off-by: Gustavo Pimentel <[email protected]>
[[email protected]: updated commit log]
Signed-off-by: Lorenzo Pieralisi <[email protected]>
Acked-by: Kishon Vijay Abraham I <[email protected]>
|
|
Remove duplicate defines located on pcie-designware.h file already
available on /include/uapi/linux/pci-regs.h file.
Signed-off-by: Gustavo Pimentel <[email protected]>
Signed-off-by: Lorenzo Pieralisi <[email protected]>
Acked-by: Kishon Vijay Abraham I <[email protected]>
|
|
Add PCIe config space capability search function.
Add sysfs set/get interface to allow the change of EP MSI-X maximum number.
Add EP MSI-X callback for triggering interruptions.
Signed-off-by: Gustavo Pimentel <[email protected]>
Signed-off-by: Lorenzo Pieralisi <[email protected]>
Acked-by: Kishon Vijay Abraham I <[email protected]>
|
|
Change {cdns, dra7xx, artpec6, dw, rockchip}_pcie_ep_raise_irq() and
pci_epc_raise_irq() signature, namely the interrupt_num variable type
from u8 to u16 to accommodate 2048 maximum MSI-X interrupts.
Signed-off-by: Gustavo Pimentel <[email protected]>
Signed-off-by: Lorenzo Pieralisi <[email protected]>
Acked-by: Alan Douglas <[email protected]>
Acked-by: Shawn Lin <[email protected]>
Acked-by: Jesper Nilsson <[email protected]>
Acked-by: Joao Pinto <[email protected]>
Acked-by: Kishon Vijay Abraham I <[email protected]>
|
|
Move specific features settings from EP shared code
(pcie-designware-ep.c) to the driver (pcie-designware-plat.c).
Previous implementation disables the EP link notification
by default for all SoCs that uses EP DesignWare IP, which affects
directly the dra7xx and artpec6 SoCs.
Signed-off-by: Gustavo Pimentel <[email protected]>
Signed-off-by: Lorenzo Pieralisi <[email protected]>
Acked-by: Kishon Vijay Abraham I <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull more overflow updates from Kees Cook:
"The rest of the overflow changes for v4.18-rc1.
This includes the explicit overflow fixes from Silvio, further
struct_size() conversions from Matthew, and a bug fix from Dan.
But the bulk of it is the treewide conversions to use either the
2-factor argument allocators (e.g. kmalloc(a * b, ...) into
kmalloc_array(a, b, ...) or the array_size() macros (e.g. vmalloc(a *
b) into vmalloc(array_size(a, b)).
Coccinelle was fighting me on several fronts, so I've done a bunch of
manual whitespace updates in the patches as well.
Summary:
- Error path bug fix for overflow tests (Dan)
- Additional struct_size() conversions (Matthew, Kees)
- Explicitly reported overflow fixes (Silvio, Kees)
- Add missing kvcalloc() function (Kees)
- Treewide conversions of allocators to use either 2-factor argument
variant when available, or array_size() and array3_size() as needed
(Kees)"
* tag 'overflow-v4.18-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (26 commits)
treewide: Use array_size in f2fs_kvzalloc()
treewide: Use array_size() in f2fs_kzalloc()
treewide: Use array_size() in f2fs_kmalloc()
treewide: Use array_size() in sock_kmalloc()
treewide: Use array_size() in kvzalloc_node()
treewide: Use array_size() in vzalloc_node()
treewide: Use array_size() in vzalloc()
treewide: Use array_size() in vmalloc()
treewide: devm_kzalloc() -> devm_kcalloc()
treewide: devm_kmalloc() -> devm_kmalloc_array()
treewide: kvzalloc() -> kvcalloc()
treewide: kvmalloc() -> kvmalloc_array()
treewide: kzalloc_node() -> kcalloc_node()
treewide: kzalloc() -> kcalloc()
treewide: kmalloc() -> kmalloc_array()
mm: Introduce kvcalloc()
video: uvesafb: Fix integer overflow in allocation
UBIFS: Fix potential integer overflow in allocation
leds: Use struct_size() in allocation
Convert intel uncore to struct_size
...
|
|
Native PCI drivers for root complex devices were originally all in
drivers/pci/host/. Some of these devices can also be operated in endpoint
mode. Drivers for endpoint mode didn't seem to fit in the "host"
directory, so we put both the root complex and endpoint drivers in
per-device directories, e.g., drivers/pci/dwc/, drivers/pci/cadence/, etc.
These per-device directories contain trivial Kconfig and Makefiles and
clutter drivers/pci/. Make a new drivers/pci/controllers/ directory and
collect all the device-specific drivers there.
No functional change intended.
Link: https://lkml.kernel.org/r/[email protected]
Signed-off-by: Shawn Lin <[email protected]>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <[email protected]>
|