| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Add error handling from calling fixed_phy_register.
It may return some error, therefore, need to check the status.
And fixed_phy_register needs to bind a device node for mdio.
Add the mac device node for fixed_phy_register function.
This is a reference to this function, of_phy_register_fixed_link().
Fixes: e24a6c874601 ("net: ftgmac100: Get link speed and duplex for NC-SI")
Signed-off-by: Jacky Chou <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Currently this driver prints this line with what looks like
a rogue format specifier when the device is probed:
[ 2.840000] eth%d: MVME147 at 0xfffe1800, irq 12, Hardware Address xx:xx:xx:xx:xx:xx
Change the printk() for netdev_info() and move it after the
registration has completed so it prints out the name of the
interface properly.
Signed-off-by: Daniel Palmer <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
All MMD reads return 0 for the RTL8126A-integrated PHY. Therefore phylib
assumes it doesn't support EEE, what results in higher power consumption,
and a significantly higher chip temperature in my case.
To fix this split out the PHY driver for the RTL8126A-integrated PHY
and set the read_mmd/write_mmd callbacks to read from vendor-specific
registers.
Fixes: 5befa3728b85 ("net: phy: realtek: add support for RTL8126A-integrated 5Gbps PHY")
Cc: [email protected]
Signed-off-by: Heiner Kallweit <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The VLAN table is a shared memory between the two ports/slices
in a ICSSG cluster and this may lead to race condition when the
common code paths for both ports are executed in different CPUs.
Fix the race condition access by locking the shared memory access
Fixes: 487f7323f39a ("net: ti: icssg-prueth: Add helper functions to configure FDB")
Signed-off-by: MD Danish Anwar <[email protected]>
Reviewed-by: Roger Quadros <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
dcr_map is called in the previous if and therefore needs to be unmapped.
Fixes: 1ff0fcfcb1a6 ("ibm_newemac: Fix new MAL feature handling")
Signed-off-by: Rosen Penev <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Sporadic issues, such as PHY access loss, have been observed on I219 (19)
devices. It was found that these devices have hardware more closely
related to ADP than MTP and the issues were caused by taking MTP-specific
flows.
Change the MAC and board types of these devices from MTP to ADP to
correctly reflect the LAN hardware, and flows, of these devices.
Fixes: db2d737d63c5 ("e1000e: Separate MTP board type from ADP")
Signed-off-by: Vitaly Lifshits <[email protected]>
Tested-by: Mor Bar-Gabay <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Commit 004d25060c78 ("igb: Fix igb_down hung on surprise removal")
changed igb_io_error_detected() to ignore non-fatal pcie errors in order
to avoid hung task that can happen when igb_down() is called multiple
times. This caused an issue when processing transient non-fatal errors.
igb_io_resume(), which is called after igb_io_error_detected(), assumes
that device is brought down by igb_io_error_detected() if the interface
is up. This resulted in panic with stacktrace below.
[ T3256] igb 0000:09:00.0 haeth0: igb: haeth0 NIC Link is Down
[ T292] pcieport 0000:00:1c.5: AER: Uncorrected (Non-Fatal) error received: 0000:09:00.0
[ T292] igb 0000:09:00.0: PCIe Bus Error: severity=Uncorrected (Non-Fatal), type=Transaction Layer, (Requester ID)
[ T292] igb 0000:09:00.0: device [8086:1537] error status/mask=00004000/00000000
[ T292] igb 0000:09:00.0: [14] CmpltTO [ 200.105524,009][ T292] igb 0000:09:00.0: AER: TLP Header: 00000000 00000000 00000000 00000000
[ T292] pcieport 0000:00:1c.5: AER: broadcast error_detected message
[ T292] igb 0000:09:00.0: Non-correctable non-fatal error reported.
[ T292] pcieport 0000:00:1c.5: AER: broadcast mmio_enabled message
[ T292] pcieport 0000:00:1c.5: AER: broadcast resume message
[ T292] ------------[ cut here ]------------
[ T292] kernel BUG at net/core/dev.c:6539!
[ T292] invalid opcode: 0000 [#1] PREEMPT SMP
[ T292] RIP: 0010:napi_enable+0x37/0x40
[ T292] Call Trace:
[ T292] <TASK>
[ T292] ? die+0x33/0x90
[ T292] ? do_trap+0xdc/0x110
[ T292] ? napi_enable+0x37/0x40
[ T292] ? do_error_trap+0x70/0xb0
[ T292] ? napi_enable+0x37/0x40
[ T292] ? napi_enable+0x37/0x40
[ T292] ? exc_invalid_op+0x4e/0x70
[ T292] ? napi_enable+0x37/0x40
[ T292] ? asm_exc_invalid_op+0x16/0x20
[ T292] ? napi_enable+0x37/0x40
[ T292] igb_up+0x41/0x150
[ T292] igb_io_resume+0x25/0x70
[ T292] report_resume+0x54/0x70
[ T292] ? report_frozen_detected+0x20/0x20
[ T292] pci_walk_bus+0x6c/0x90
[ T292] ? aer_print_port_info+0xa0/0xa0
[ T292] pcie_do_recovery+0x22f/0x380
[ T292] aer_process_err_devices+0x110/0x160
[ T292] aer_isr+0x1c1/0x1e0
[ T292] ? disable_irq_nosync+0x10/0x10
[ T292] irq_thread_fn+0x1a/0x60
[ T292] irq_thread+0xe3/0x1a0
[ T292] ? irq_set_affinity_notifier+0x120/0x120
[ T292] ? irq_affinity_notify+0x100/0x100
[ T292] kthread+0xe2/0x110
[ T292] ? kthread_complete_and_exit+0x20/0x20
[ T292] ret_from_fork+0x2d/0x50
[ T292] ? kthread_complete_and_exit+0x20/0x20
[ T292] ret_from_fork_asm+0x11/0x20
[ T292] </TASK>
To fix this issue igb_io_resume() checks if the interface is running and
the device is not down this means igb_io_error_detected() did not bring
the device down and there is no need to bring it up.
Signed-off-by: Mohamed Khalfella <[email protected]>
Reviewed-by: Yuanyuan Zhong <[email protected]>
Fixes: 004d25060c78 ("igb: Fix igb_down hung on surprise removal")
Reviewed-by: Simon Horman <[email protected]>
Tested-by: Pucha Himasekhar Reddy <[email protected]> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <[email protected]>
|
|
This patch addresses a macvlan leak issue in the i40e driver caused by
concurrent access to vsi->mac_filter_hash. The leak occurs when multiple
threads attempt to modify the mac_filter_hash simultaneously, leading to
inconsistent state and potential memory leaks.
To fix this, we now wrap the calls to i40e_del_mac_filter() and zeroing
vf->default_lan_addr.addr with spin_lock/unlock_bh(&vsi->mac_filter_hash_lock),
ensuring atomic operations and preventing concurrent access.
Additionally, we add lockdep_assert_held(&vsi->mac_filter_hash_lock) in
i40e_add_mac_filter() to help catch similar issues in the future.
Reproduction steps:
1. Spawn VFs and configure port vlan on them.
2. Trigger concurrent macvlan operations (e.g., adding and deleting
portvlan and/or mac filters).
3. Observe the potential memory leak and inconsistent state in the
mac_filter_hash.
This synchronization ensures the integrity of the mac_filter_hash and prevents
the described leak.
Fixes: fed0d9f13266 ("i40e: Fix VF's MAC Address change on VM")
Reviewed-by: Arkadiusz Kubalewski <[email protected]>
Signed-off-by: Aleksandr Loktionov <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Tested-by: Rafal Romanowski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Increasing MSI-X value on a VF leads to invalid memory operations. This
is caused by not reallocating some arrays.
Reproducer:
modprobe ice
echo 0 > /sys/bus/pci/devices/$PF_PCI/sriov_drivers_autoprobe
echo 1 > /sys/bus/pci/devices/$PF_PCI/sriov_numvfs
echo 17 > /sys/bus/pci/devices/$VF0_PCI/sriov_vf_msix_count
Default MSI-X is 16, so 17 and above triggers this issue.
KASAN reports:
BUG: KASAN: slab-out-of-bounds in ice_vsi_alloc_ring_stats+0x38d/0x4b0 [ice]
Read of size 8 at addr ffff8888b937d180 by task bash/28433
(...)
Call Trace:
(...)
? ice_vsi_alloc_ring_stats+0x38d/0x4b0 [ice]
kasan_report+0xed/0x120
? ice_vsi_alloc_ring_stats+0x38d/0x4b0 [ice]
ice_vsi_alloc_ring_stats+0x38d/0x4b0 [ice]
ice_vsi_cfg_def+0x3360/0x4770 [ice]
? mutex_unlock+0x83/0xd0
? __pfx_ice_vsi_cfg_def+0x10/0x10 [ice]
? __pfx_ice_remove_vsi_lkup_fltr+0x10/0x10 [ice]
ice_vsi_cfg+0x7f/0x3b0 [ice]
ice_vf_reconfig_vsi+0x114/0x210 [ice]
ice_sriov_set_msix_vec_count+0x3d0/0x960 [ice]
sriov_vf_msix_count_store+0x21c/0x300
(...)
Allocated by task 28201:
(...)
ice_vsi_cfg_def+0x1c8e/0x4770 [ice]
ice_vsi_cfg+0x7f/0x3b0 [ice]
ice_vsi_setup+0x179/0xa30 [ice]
ice_sriov_configure+0xcaa/0x1520 [ice]
sriov_numvfs_store+0x212/0x390
(...)
To fix it, use ice_vsi_rebuild() instead of ice_vf_reconfig_vsi(). This
causes the required arrays to be reallocated taking the new queue count
into account (ice_vsi_realloc_stat_arrays()). Set req_txq and req_rxq
before ice_vsi_rebuild(), so that realloc uses the newly set queue
count.
Additionally, ice_vsi_rebuild() does not remove VSI filters
(ice_fltr_remove_all()), so ice_vf_init_host_cfg() is no longer
necessary.
Reported-by: Jacob Keller <[email protected]>
Fixes: 2a2cb4c6c181 ("ice: replace ice_vf_recreate_vsi() with ice_vf_reconfig_vsi()")
Reviewed-by: Michal Swiatkowski <[email protected]>
Signed-off-by: Marcin Szycik <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Tested-by: Rafal Romanowski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Triggering the reset while in switchdev mode causes
errors[1]. Rules are already removed by this time
because switch content is flushed in case of the reset.
This means that rules were deleted from HW but SW
still thinks they exist so when we get
SWITCHDEV_FDB_DEL_TO_DEVICE notification we try to
delete not existing rule.
We can avoid these errors by clearing the rules
early in the reset flow before they are removed from HW.
Switchdev API will get notified that the rule was removed
so we won't get SWITCHDEV_FDB_DEL_TO_DEVICE notification.
Remove unnecessary ice_clear_sw_switch_recipes.
[1]
ice 0000:01:00.0: Failed to delete FDB forward rule, err: -2
ice 0000:01:00.0: Failed to delete FDB guard rule, err: -2
Fixes: 7c945a1a8e5f ("ice: Switchdev FDB events support")
Reviewed-by: Mateusz Polchlopek <[email protected]>
Signed-off-by: Wojciech Drewek <[email protected]>
Tested-by: Sujai Buvaneswaran <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
netif_is_ice() works by checking the pointer to netdev ops. However, it
only checks for the default ice_netdev_ops, not ice_netdev_safe_mode_ops,
so in Safe Mode it always returns false, which is unintuitive. While it
doesn't look like netif_is_ice() is currently being called anywhere in Safe
Mode, this could change and potentially lead to unexpected behaviour.
Fixes: df006dd4b1dc ("ice: Add initial support framework for LAG")
Reviewed-by: Przemek Kitszel <[email protected]>
Signed-off-by: Marcin Szycik <[email protected]>
Reviewed-by: Brett Creeley <[email protected]>
Tested-by: Sujai Buvaneswaran <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
If DDP package is missing or corrupted, the driver should enter Safe Mode.
Instead, an error is returned and probe fails.
To fix this, don't exit init if ice_init_ddp_config() returns an error.
Repro:
* Remove or rename DDP package (/lib/firmware/intel/ice/ddp/ice.pkg)
* Load ice
Fixes: cc5776fe1832 ("ice: Enable switching default Tx scheduler topology")
Reviewed-by: Przemek Kitszel <[email protected]>
Signed-off-by: Marcin Szycik <[email protected]>
Reviewed-by: Brett Creeley <[email protected]>
Tested-by: Pucha Himasekhar Reddy <[email protected]> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <[email protected]>
|
|
-Wflex-array-member-not-at-end was introduced in GCC-14, and we are
getting ready to enable it, globally.
So, in order to avoid ending up with a flexible-array member in the
middle of multiple other structs, we use the `__struct_group()`
helper to create a new tagged `struct ieee80211_radiotap_header_fixed`.
This structure groups together all the members of the flexible
`struct ieee80211_radiotap_header` except the flexible array.
As a result, the array is effectively separated from the rest of the
members without modifying the memory layout of the flexible structure.
We then change the type of the middle struct members currently causing
trouble from `struct ieee80211_radiotap_header` to `struct
ieee80211_radiotap_header_fixed`.
We also want to ensure that in case new members need to be added to the
flexible structure, they are always included within the newly created
tagged struct. For this, we use `static_assert()`. This ensures that the
memory layout for both the flexible structure and the new tagged struct
is the same after any changes.
This approach avoids having to implement `struct ieee80211_radiotap_header_fixed`
as a completely separate structure, thus preventing having to maintain
two independent but basically identical structures, closing the door
to potential bugs in the future.
So, with these changes, fix the following warnings:
drivers/net/wireless/ath/wil6210/txrx.c:309:50: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/intel/ipw2x00/ipw2100.c:2521:50: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/intel/ipw2x00/ipw2200.h:1146:42: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/intel/ipw2x00/libipw.h:595:36: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/marvell/libertas/radiotap.h:34:42: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/marvell/libertas/radiotap.h:5:42: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/microchip/wilc1000/mon.c:10:42: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/microchip/wilc1000/mon.c:15:42: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/virtual/mac80211_hwsim.c:758:42: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/virtual/mac80211_hwsim.c:767:42: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
Signed-off-by: Gustavo A. R. Silva <[email protected]>
Link: https://patch.msgid.link/ZwBMtBZKcrzwU7l4@kspp
Signed-off-by: Johannes Berg <[email protected]>
|
|
iwl4965 fails upon resume from hibernation on my laptop. The reason
seems to be a stale interrupt which isn't being cleared out before
interrupts are enabled. We end up with a race beween the resume
trying to bring things back up, and the restart work (queued form
the interrupt handler) trying to bring things down. Eventually
the whole thing blows up.
Fix the problem by clearing out any stale interrupts before
interrupts get enabled during resume.
Here's a debug log of the indicent:
[ 12.042589] ieee80211 phy0: il_isr ISR inta 0x00000080, enabled 0xaa00008b, fh 0x00000000
[ 12.042625] ieee80211 phy0: il4965_irq_tasklet inta 0x00000080, enabled 0x00000000, fh 0x00000000
[ 12.042651] iwl4965 0000:10:00.0: RF_KILL bit toggled to enable radio.
[ 12.042653] iwl4965 0000:10:00.0: On demand firmware reload
[ 12.042690] ieee80211 phy0: il4965_irq_tasklet End inta 0x00000000, enabled 0xaa00008b, fh 0x00000000, flags 0x00000282
[ 12.052207] ieee80211 phy0: il4965_mac_start enter
[ 12.052212] ieee80211 phy0: il_prep_station Add STA to driver ID 31: ff:ff:ff:ff:ff:ff
[ 12.052244] ieee80211 phy0: il4965_set_hw_ready hardware ready
[ 12.052324] ieee80211 phy0: il_apm_init Init card's basic functions
[ 12.052348] ieee80211 phy0: il_apm_init L1 Enabled; Disabling L0S
[ 12.055727] ieee80211 phy0: il4965_load_bsm Begin load bsm
[ 12.056140] ieee80211 phy0: il4965_verify_bsm Begin verify bsm
[ 12.058642] ieee80211 phy0: il4965_verify_bsm BSM bootstrap uCode image OK
[ 12.058721] ieee80211 phy0: il4965_load_bsm BSM write complete, poll 1 iterations
[ 12.058734] ieee80211 phy0: __il4965_up iwl4965 is coming up
[ 12.058737] ieee80211 phy0: il4965_mac_start Start UP work done.
[ 12.058757] ieee80211 phy0: __il4965_down iwl4965 is going down
[ 12.058761] ieee80211 phy0: il_scan_cancel_timeout Scan cancel timeout
[ 12.058762] ieee80211 phy0: il_do_scan_abort Not performing scan to abort
[ 12.058765] ieee80211 phy0: il_clear_ucode_stations Clearing ucode stations in driver
[ 12.058767] ieee80211 phy0: il_clear_ucode_stations No active stations found to be cleared
[ 12.058819] ieee80211 phy0: _il_apm_stop Stop card, put in low power state
[ 12.058827] ieee80211 phy0: _il_apm_stop_master stop master
[ 12.058864] ieee80211 phy0: il4965_clear_free_frames 0 frames on pre-allocated heap on clear.
[ 12.058869] ieee80211 phy0: Hardware restart was requested
[ 16.132299] iwl4965 0000:10:00.0: START_ALIVE timeout after 4000ms.
[ 16.132303] ------------[ cut here ]------------
[ 16.132304] Hardware became unavailable upon resume. This could be a software issue prior to suspend or a hardware issue.
[ 16.132338] WARNING: CPU: 0 PID: 181 at net/mac80211/util.c:1826 ieee80211_reconfig+0x8f/0x14b0 [mac80211]
[ 16.132390] Modules linked in: ctr ccm sch_fq_codel xt_tcpudp xt_multiport xt_state iptable_filter iptable_nat nf_nat nf_conntrack nf_defrag_ipv4 ip_tables x_tables binfmt_misc joydev mousedev btusb btrtl btintel btbcm bluetooth ecdh_generic ecc iTCO_wdt i2c_dev iwl4965 iwlegacy coretemp snd_hda_codec_analog pcspkr psmouse mac80211 snd_hda_codec_generic libarc4 sdhci_pci cqhci sha256_generic sdhci libsha256 firewire_ohci snd_hda_intel snd_intel_dspcfg mmc_core snd_hda_codec snd_hwdep firewire_core led_class iosf_mbi snd_hda_core uhci_hcd lpc_ich crc_itu_t cfg80211 ehci_pci ehci_hcd snd_pcm usbcore mfd_core rfkill snd_timer snd usb_common soundcore video parport_pc parport intel_agp wmi intel_gtt backlight e1000e agpgart evdev
[ 16.132456] CPU: 0 UID: 0 PID: 181 Comm: kworker/u8:6 Not tainted 6.11.0-cl+ #143
[ 16.132460] Hardware name: Hewlett-Packard HP Compaq 6910p/30BE, BIOS 68MCU Ver. F.19 07/06/2010
[ 16.132463] Workqueue: async async_run_entry_fn
[ 16.132469] RIP: 0010:ieee80211_reconfig+0x8f/0x14b0 [mac80211]
[ 16.132501] Code: da 02 00 00 c6 83 ad 05 00 00 00 48 89 df e8 98 1b fc ff 85 c0 41 89 c7 0f 84 e9 02 00 00 48 c7 c7 a0 e6 48 a0 e8 d1 77 c4 e0 <0f> 0b eb 2d 84 c0 0f 85 8b 01 00 00 c6 87 ad 05 00 00 00 e8 69 1b
[ 16.132504] RSP: 0018:ffffc9000029fcf0 EFLAGS: 00010282
[ 16.132507] RAX: 0000000000000000 RBX: ffff8880072008e0 RCX: 0000000000000001
[ 16.132509] RDX: ffffffff81f21a18 RSI: 0000000000000086 RDI: 0000000000000001
[ 16.132510] RBP: ffff8880072003c0 R08: 0000000000000000 R09: 0000000000000003
[ 16.132512] R10: 0000000000000000 R11: ffff88807e5b0000 R12: 0000000000000001
[ 16.132514] R13: 0000000000000000 R14: 0000000000000000 R15: 00000000ffffff92
[ 16.132515] FS: 0000000000000000(0000) GS:ffff88807c200000(0000) knlGS:0000000000000000
[ 16.132517] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 16.132519] CR2: 000055dd43786c08 CR3: 000000000978f000 CR4: 00000000000006f0
[ 16.132521] Call Trace:
[ 16.132525] <TASK>
[ 16.132526] ? __warn+0x77/0x120
[ 16.132532] ? ieee80211_reconfig+0x8f/0x14b0 [mac80211]
[ 16.132564] ? report_bug+0x15c/0x190
[ 16.132568] ? handle_bug+0x36/0x70
[ 16.132571] ? exc_invalid_op+0x13/0x60
[ 16.132573] ? asm_exc_invalid_op+0x16/0x20
[ 16.132579] ? ieee80211_reconfig+0x8f/0x14b0 [mac80211]
[ 16.132611] ? snd_hdac_bus_init_cmd_io+0x24/0x200 [snd_hda_core]
[ 16.132617] ? pick_eevdf+0x133/0x1c0
[ 16.132622] ? check_preempt_wakeup_fair+0x70/0x90
[ 16.132626] ? wakeup_preempt+0x4a/0x60
[ 16.132628] ? ttwu_do_activate.isra.0+0x5a/0x190
[ 16.132632] wiphy_resume+0x79/0x1a0 [cfg80211]
[ 16.132675] ? wiphy_suspend+0x2a0/0x2a0 [cfg80211]
[ 16.132697] dpm_run_callback+0x75/0x1b0
[ 16.132703] device_resume+0x97/0x200
[ 16.132707] async_resume+0x14/0x20
[ 16.132711] async_run_entry_fn+0x1b/0xa0
[ 16.132714] process_one_work+0x13d/0x350
[ 16.132718] worker_thread+0x2be/0x3d0
[ 16.132722] ? cancel_delayed_work_sync+0x70/0x70
[ 16.132725] kthread+0xc0/0xf0
[ 16.132729] ? kthread_park+0x80/0x80
[ 16.132732] ret_from_fork+0x28/0x40
[ 16.132735] ? kthread_park+0x80/0x80
[ 16.132738] ret_from_fork_asm+0x11/0x20
[ 16.132741] </TASK>
[ 16.132742] ---[ end trace 0000000000000000 ]---
[ 16.132930] ------------[ cut here ]------------
[ 16.132932] WARNING: CPU: 0 PID: 181 at net/mac80211/driver-ops.c:41 drv_stop+0xe7/0xf0 [mac80211]
[ 16.132957] Modules linked in: ctr ccm sch_fq_codel xt_tcpudp xt_multiport xt_state iptable_filter iptable_nat nf_nat nf_conntrack nf_defrag_ipv4 ip_tables x_tables binfmt_misc joydev mousedev btusb btrtl btintel btbcm bluetooth ecdh_generic ecc iTCO_wdt i2c_dev iwl4965 iwlegacy coretemp snd_hda_codec_analog pcspkr psmouse mac80211 snd_hda_codec_generic libarc4 sdhci_pci cqhci sha256_generic sdhci libsha256 firewire_ohci snd_hda_intel snd_intel_dspcfg mmc_core snd_hda_codec snd_hwdep firewire_core led_class iosf_mbi snd_hda_core uhci_hcd lpc_ich crc_itu_t cfg80211 ehci_pci ehci_hcd snd_pcm usbcore mfd_core rfkill snd_timer snd usb_common soundcore video parport_pc parport intel_agp wmi intel_gtt backlight e1000e agpgart evdev
[ 16.133014] CPU: 0 UID: 0 PID: 181 Comm: kworker/u8:6 Tainted: G W 6.11.0-cl+ #143
[ 16.133018] Tainted: [W]=WARN
[ 16.133019] Hardware name: Hewlett-Packard HP Compaq 6910p/30BE, BIOS 68MCU Ver. F.19 07/06/2010
[ 16.133021] Workqueue: async async_run_entry_fn
[ 16.133025] RIP: 0010:drv_stop+0xe7/0xf0 [mac80211]
[ 16.133048] Code: 48 85 c0 74 0e 48 8b 78 08 89 ea 48 89 de e8 e0 87 04 00 65 ff 0d d1 de c4 5f 0f 85 42 ff ff ff e8 be 52 c2 e0 e9 38 ff ff ff <0f> 0b 5b 5d c3 0f 1f 40 00 41 54 49 89 fc 55 53 48 89 f3 2e 2e 2e
[ 16.133050] RSP: 0018:ffffc9000029fc50 EFLAGS: 00010246
[ 16.133053] RAX: 0000000000000000 RBX: ffff8880072008e0 RCX: ffff88800377f6c0
[ 16.133054] RDX: 0000000000000001 RSI: 0000000000000000 RDI: ffff8880072008e0
[ 16.133056] RBP: 0000000000000000 R08: ffffffff81f238d8 R09: 0000000000000000
[ 16.133058] R10: ffff8880080520f0 R11: 0000000000000000 R12: ffff888008051c60
[ 16.133060] R13: ffff8880072008e0 R14: 0000000000000000 R15: ffff8880072011d8
[ 16.133061] FS: 0000000000000000(0000) GS:ffff88807c200000(0000) knlGS:0000000000000000
[ 16.133063] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 16.133065] CR2: 000055dd43786c08 CR3: 000000000978f000 CR4: 00000000000006f0
[ 16.133067] Call Trace:
[ 16.133069] <TASK>
[ 16.133070] ? __warn+0x77/0x120
[ 16.133075] ? drv_stop+0xe7/0xf0 [mac80211]
[ 16.133098] ? report_bug+0x15c/0x190
[ 16.133100] ? handle_bug+0x36/0x70
[ 16.133103] ? exc_invalid_op+0x13/0x60
[ 16.133105] ? asm_exc_invalid_op+0x16/0x20
[ 16.133109] ? drv_stop+0xe7/0xf0 [mac80211]
[ 16.133132] ieee80211_do_stop+0x55a/0x810 [mac80211]
[ 16.133161] ? fq_codel_reset+0xa5/0xc0 [sch_fq_codel]
[ 16.133164] ieee80211_stop+0x4f/0x180 [mac80211]
[ 16.133192] __dev_close_many+0xa2/0x120
[ 16.133195] dev_close_many+0x90/0x150
[ 16.133198] dev_close+0x5d/0x80
[ 16.133200] cfg80211_shutdown_all_interfaces+0x40/0xe0 [cfg80211]
[ 16.133223] wiphy_resume+0xb2/0x1a0 [cfg80211]
[ 16.133247] ? wiphy_suspend+0x2a0/0x2a0 [cfg80211]
[ 16.133269] dpm_run_callback+0x75/0x1b0
[ 16.133273] device_resume+0x97/0x200
[ 16.133277] async_resume+0x14/0x20
[ 16.133280] async_run_entry_fn+0x1b/0xa0
[ 16.133283] process_one_work+0x13d/0x350
[ 16.133287] worker_thread+0x2be/0x3d0
[ 16.133290] ? cancel_delayed_work_sync+0x70/0x70
[ 16.133294] kthread+0xc0/0xf0
[ 16.133296] ? kthread_park+0x80/0x80
[ 16.133299] ret_from_fork+0x28/0x40
[ 16.133302] ? kthread_park+0x80/0x80
[ 16.133304] ret_from_fork_asm+0x11/0x20
[ 16.133307] </TASK>
[ 16.133308] ---[ end trace 0000000000000000 ]---
[ 16.133335] ieee80211 phy0: PM: dpm_run_callback(): wiphy_resume [cfg80211] returns -110
[ 16.133360] ieee80211 phy0: PM: failed to restore async: error -110
Cc: [email protected]
Cc: Stanislaw Gruszka <[email protected]>
Cc: Kalle Valo <[email protected]>
Cc: [email protected]
Signed-off-by: Ville Syrjälä <[email protected]>
Acked-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Link: https://patch.msgid.link/[email protected]
|
|
All modern chips support and need the 10_100 bit set for supporting jumbo
frames on 10/100 ports, so instead of enabling it only for 583XX enable
it for everything except bcm63xx, where the bit is writeable, but does
nothing.
Tested on BCM53115, where jumbo frames were dropped at 10/100 speeds
without the bit set.
Fixes: 6ae5834b983a ("net: dsa: b53: add MTU configuration support")
Signed-off-by: Jonas Gorski <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: Paolo Abeni <[email protected]>
|
|
While BCM5325/5365 do not support jumbo frames, they do support slightly
oversized frames, so do not error out if requesting a supported MTU for
them.
Fixes: 6ae5834b983a ("net: dsa: b53: add MTU configuration support")
Signed-off-by: Jonas Gorski <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: Paolo Abeni <[email protected]>
|
|
BCM5325/BCM5365 do not support jumbo frames, so we should not report a
jumbo frame mtu for them. But they do support so called "oversized"
frames up to 1536 bytes long by default, so report an appropriate MTU.
Fixes: 6ae5834b983a ("net: dsa: b53: add MTU configuration support")
Signed-off-by: Jonas Gorski <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: Paolo Abeni <[email protected]>
|
|
JMS_MAX_SIZE is the ethernet frame length, not the MTU, which is payload
without ethernet headers.
According to the datasheets maximum supported frame length for most
gigabyte swithes is 9720 bytes, so convert that to the expected MTU when
using VLAN tagged frames.
Fixes: 6ae5834b983a ("net: dsa: b53: add MTU configuration support")
Signed-off-by: Jonas Gorski <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: Paolo Abeni <[email protected]>
|
|
JMS_MIN_SIZE is the full ethernet frame length, while mtu is just the
data payload size. Comparing these two meant that mtus between 1500 and
1518 did not trigger enabling jumbo frames.
So instead compare the set mtu ETH_DATA_LEN, which is equal to
JMS_MIN_SIZE - ETH_HLEN - ETH_FCS_LEN;
Also do a check that the requested mtu is actually greater than the
minimum length, else we do not need to enable jumbo frames.
In practice this only introduced a very small range of mtus that did not
work properly. Newer chips allow 2000 byte large frames by default, and
older chips allow 1536 bytes long, which is equivalent to an mtu of
1514. So effectivly only mtus of 1515~1517 were broken.
Fixes: 6ae5834b983a ("net: dsa: b53: add MTU configuration support")
Signed-off-by: Jonas Gorski <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: Paolo Abeni <[email protected]>
|
|
Usage of devm_alloc_etherdev_mqs() conflicts with
am65_cpsw_nuss_cleanup_ndev() as the same struct net_device instances
get unregistered twice. Switch to alloc_etherdev_mqs() and make sure
am65_cpsw_nuss_cleanup_ndev() unregisters and frees those net_device
instances properly.
With this, it is finally possible to rmmod the driver without oopsing
the kernel.
Fixes: 93a76530316a ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver")
Signed-off-by: Nicolas Pitre <[email protected]>
Reviewed-by: Roger Quadros <[email protected]>
Signed-off-by: Paolo Abeni <[email protected]>
|
|
In am65_cpsw_nuss_remove(), move the call to am65_cpsw_unregister_devlink()
after am65_cpsw_nuss_cleanup_ndev() to avoid triggering the
WARN_ON(devlink_port->type != DEVLINK_PORT_TYPE_NOTSET) in
devl_port_unregister(). Makes it coherent with usage in
m65_cpsw_nuss_register_ndevs()'s cleanup path.
Fixes: 58356eb31d60 ("net: ti: am65-cpsw-nuss: Add devlink support")
Signed-off-by: Nicolas Pitre <[email protected]>
Reviewed-by: Roger Quadros <[email protected]>
Signed-off-by: Paolo Abeni <[email protected]>
|
|
Move the tx cpu dma ring index update out of transmit loop of
airoha_dev_xmit routine in order to not start transmitting the packet
before it is fully DMA mapped (e.g. fragmented skbs).
Fixes: 23020f049327 ("net: airoha: Introduce ethernet support for EN7581 SoC")
Reported-by: Felix Fietkau <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Link: https://patch.msgid.link/20241004-airoha-eth-7581-mapping-fix-v1-1-8e4279ab1812@kernel.org
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Commit c938ab4da0eb ("net: phy: Manual remove LEDs to ensure correct
ordering") correctly fixed a problem with using devm_ but missed
removing the LED entry from the LEDs list.
This cause kernel panic on specific scenario where the port for the PHY
is torn down and up and the kmod for the PHY is removed.
On setting the port down the first time, the assosiacted LEDs are
correctly unregistered. The associated kmod for the PHY is now removed.
The kmod is now added again and the port is now put up, the associated LED
are registered again.
On putting the port down again for the second time after these step, the
LED list now have 4 elements. With the first 2 already unregistered
previously and the 2 new one registered again.
This cause a kernel panic as the first 2 element should have been
removed.
Fix this by correctly removing the element when LED is unregistered.
Reported-by: Daniel Golle <[email protected]>
Tested-by: Daniel Golle <[email protected]>
Cc: [email protected]
Fixes: c938ab4da0eb ("net: phy: Manual remove LEDs to ensure correct ordering")
Signed-off-by: Christian Marangi <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
adin1110_read_fifo()
If 'frame_size' is too small or if 'round_len' is an error code, it is
likely that an error code should be returned to the caller.
Actually, 'ret' is likely to be 0, so if one of these sanity checks fails,
'success' is returned.
Return -EINVAL instead.
Fixes: bc93e19d088b ("net: ethernet: adi: Add ADIN1110 support")
Signed-off-by: Christophe JAILLET <[email protected]>
Link: https://patch.msgid.link/8ff73b40f50d8fa994a454911b66adebce8da266.1727981562.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
This reverts commit b514c47ebf41a6536551ed28a05758036e6eca7c.
The commit describes that we don't have to sync the page when
recycling, and it tries to optimize that case. But we do need
to sync after allocation. Recycling side should be changed to
pass the right sync size instead.
Fixes: b514c47ebf41 ("net: stmmac: set PP_FLAG_DMA_SYNC_DEV only if XDP is enabled")
Reported-by: Jon Hunter <[email protected]>
Link: https://lore.kernel.org/[email protected]
Reviewed-by: Jacob Keller <[email protected]>
Reviewed-by: Furong Xu <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Accessing device registers seems to be not reliable, the chip
revision is sometimes detected wrongly (0 instead of expected 1).
Ensure that the chip reset is performed via reset GPIO and then
wait for 'Device Ready' status in HW_CFG register before doing
any register initializations.
Cc: [email protected]
Fixes: a1292595e006 ("net: dsa: add new DSA switch driver for the SMSC-LAN9303")
Signed-off-by: Anatolij Gustschin <[email protected]>
[alex: reworked using read_poll_timeout()]
Signed-off-by: Alexander Sverdlin <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
If phy_read_mmd() fails, the error code stored in 'bmsr' should be returned
instead of 'val' which is likely to be 0.
Fixes: 75f4d8d10e01 ("net: phy: add Broadcom BCM84881 PHY driver")
Signed-off-by: Christophe JAILLET <[email protected]>
Link: https://patch.msgid.link/3e1755b0c40340d00e089d6adae5bca2f8c79e53.1727982168.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
PSE controllers like the TPS23881 can forcefully turn off their
configuration state. In such cases, the is_enabled() and get_status()
callbacks will report the PSE as disabled, while admin_state_enabled
will show it as enabled. This mismatch can lead the user to attempt
to enable it, but no action is taken as admin_state_enabled remains set.
The solution is to disable the PSE before enabling it, ensuring the
actual status matches admin_state_enabled.
Fixes: d83e13761d5b ("net: pse-pd: Use regulator framework within PSE framework")
Signed-off-by: Kory Maincent <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Previously, the TX header requirement for standard frames was ignored.
This requirement is a bitstring sent from the VIOS which maps to the
type of header information needed during TX. If no header information,
is needed then send subcrq direct can be used (which can be more
performant).
This bitstring was previously ignored for standard packets (AKA non LSO,
non CSO) due to the belief that the bitstring was over-cautionary. It
turns out that there are some configurations where the backing device
does need header information for transmission of standard packets. If
the information is not supplied then this causes continuous "Adapter
error" transport events. Therefore, this bitstring should be respected
and observed before considering the use of send subcrq direct.
Fixes: 74839f7a8268 ("ibmvnic: Introduce send sub-crq direct")
Signed-off-by: Nick Child <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
The blamed commit introduced an unexpected regression in the sja1105
driver. Packets from VLAN-unaware bridge ports get received correctly,
but the protocol stack can't seem to decode them properly.
For ds->untag_bridge_pvid users (thus also sja1105), the blamed commit
did introduce a functional change: dsa_switch_rcv() used to call
dsa_untag_bridge_pvid(), which looked like this:
err = br_vlan_get_proto(br, &proto);
if (err)
return skb;
/* Move VLAN tag from data to hwaccel */
if (!skb_vlan_tag_present(skb) && skb->protocol == htons(proto)) {
skb = skb_vlan_untag(skb);
if (!skb)
return NULL;
}
and now it calls dsa_software_vlan_untag() which has just this:
/* Move VLAN tag from data to hwaccel */
if (!skb_vlan_tag_present(skb)) {
skb = skb_vlan_untag(skb);
if (!skb)
return NULL;
}
thus lacks any skb->protocol == bridge VLAN protocol check. That check
is deferred until a later check for skb->vlan_proto (in the hwaccel area).
The new code is problematic because, for VLAN-untagged packets,
skb_vlan_untag() blindly takes the 4 bytes starting with the EtherType
and turns them into a hwaccel VLAN tag. This is what breaks the protocol
stack.
It would be tempting to "make it work as before" and only call
skb_vlan_untag() for those packets with the skb->protocol actually
representing a VLAN.
But the premise of the newly introduced dsa_software_vlan_untag() core
function is not wrong. Drivers set ds->untag_bridge_pvid or
ds->untag_vlan_aware_bridge_pvid presumably because they send all
traffic to the CPU reception path as VLAN-tagged. So why should we spend
any additional CPU cycles assuming that the packet may be VLAN-untagged?
And why does the sja1105 driver opt into ds->untag_bridge_pvid if it
doesn't always deliver packets to the CPU as VLAN-tagged?
The answer to the latter question is indeed more interesting: it doesn't
need to. This got done in commit 884be12f8566 ("net: dsa: sja1105: add
support for imprecise RX"), because I thought it would be needed, but I
didn't realize that it doesn't actually make a difference.
As explained in the commit message of the blamed patch, ds->untag_bridge_pvid
only makes a difference in the VLAN-untagged receive path of a bridge port.
However, in that operating mode, tag_sja1105.c makes use of VLAN tags
with the ETH_P_SJA1105 TPID, and it decodes and consumes these VLAN tags
as if they were DSA tags (aka tag_8021q operation). Even if commit
884be12f8566 ("net: dsa: sja1105: add support for imprecise RX") added
this logic in sja1105_bridge_vlan_add():
/* Always install bridge VLANs as egress-tagged on the CPU port. */
if (dsa_is_cpu_port(ds, port))
flags = 0;
that was for _bridge_ VLANs, which are _not_ committed to hardware
in VLAN-unaware mode (aka the mode where ds->untag_bridge_pvid does
anything at all). Even prior to that change, the tag_8021q VLANs
were always installed as egress-tagged on the CPU port, see
dsa_switch_tag_8021q_vlan_add():
u16 flags = 0; // egress-tagged, non-PVID
if (dsa_port_is_user(dp))
flags |= BRIDGE_VLAN_INFO_UNTAGGED |
BRIDGE_VLAN_INFO_PVID;
err = dsa_port_do_tag_8021q_vlan_add(dp, info->vid,
flags);
if (err)
return err;
Whether the sja1105 driver needs the new flag, ds->untag_vlan_aware_bridge_pvid,
rather than ds->untag_bridge_pvid, is a separate discussion. To fix the
current bug in VLAN-unaware bridge mode, I would argue that the sja1105
driver should not request something it doesn't need, rather than
complicating the core DSA helper. Whereas before the blamed commit, this
setting was harmless, now it has caused breakage.
Fixes: 93e4649efa96 ("net: dsa: provide a software untagging function on RX for VLAN-aware bridges")
Signed-off-by: Vladimir Oltean <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2024-09-30 (ice, idpf)
This series contains updates to ice and idpf drivers:
For ice:
Michal corrects setting of dst VSI on LAN filters and adds clearing of
port VLAN configuration during reset.
Gui-Dong Han corrects failures to decrement refcount in some error
paths.
Przemek resolves a memory leak in ice_init_tx_topology().
Arkadiusz prevents setting of DPLL_PIN_STATE_SELECTABLE to an improper
value.
Dave stops clearing of VLAN tracking bit to allow for VLANs to be properly
restored after reset.
For idpf:
Ahmed sets uninitialized dyn_ctl_intrvl_s value.
Josh corrects use and reporting of mailbox size.
Larysa corrects order of function calls during de-initialization.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
idpf: deinit virtchnl transaction manager after vport and vectors
idpf: use actual mbx receive payload length
idpf: fix VF dynamic interrupt ctl register initialization
ice: fix VLAN replay after reset
ice: disallow DPLL_PIN_STATE_SELECTABLE for dpll output pins
ice: fix memleak in ice_init_tx_topology()
ice: clear port vlan config during reset
ice: Fix improper handling of refcount in ice_sriov_set_msix_vec_count()
ice: Fix improper handling of refcount in ice_dpll_init_rclk_pins()
ice: set correct dst VSI in only LAN filters
====================
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Remove the use of phy_set_max_speed in phy driver as the
function is mainly used in MAC driver to set the max
speed.
Instead use get_features to fix up Phy PMA capabilities for
AQR111, AQR111B0, AQR114C and AQCS109
Fixes: 038ba1dc4e54 ("net: phy: aquantia: add AQR111 and AQR111B0 PHY ID")
Fixes: 0974f1f03b07 ("net: phy: aquantia: remove false 5G and 10G speed ability for AQCS109")
Fixes: c278ec644377 ("net: phy: aquantia: add support for AQR114C PHY ID")
Link: https://lore.kernel.org/all/[email protected]/T/
Signed-off-by: Abhishek Chauhan <[email protected]>
Reviewed-by: Russell King (Oracle) <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
AQR115c reports incorrect PMA capabilities which includes
10G/5G and also incorrectly disables capabilities like autoneg
and 10Mbps support.
AQR115c as per the Marvell databook supports speeds up to 2.5Gbps
with autonegotiation.
Fixes: 0ebc581f8a4b ("net: phy: aquantia: add support for aqr115c")
Link: https://lore.kernel.org/all/[email protected]/T/
Signed-off-by: Abhishek Chauhan <[email protected]>
Reviewed-by: Russell King (Oracle) <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Yury reported a crash in the sfc driver originated from
netpoll_send_udp(). The netconsole sends a message and then netpoll
invokes the driver's NAPI function with a budget of zero. It is
dedicated to allow driver to free TX resources, that it may have used
while sending the packet.
In the netpoll case the driver invokes xdp_do_flush() unconditionally,
leading to crash because bpf_net_context was never assigned.
Invoke xdp_do_flush() only if budget is not zero.
Fixes: 401cb7dae8130 ("net: Reference bpf_redirect_info via task_struct on PREEMPT_RT.")
Reported-by: Yury Vostrikov <[email protected]>
Closes: https://lore.kernel.org/[email protected]
Signed-off-by: Sebastian Andrzej Siewior <[email protected]>
Reviewed-by: Edward Cree <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
When configuring the fiber port, the DP83869 PHY driver incorrectly
calls linkmode_set_bit() with a bit mask (1 << 10) rather than a bit
number (10). This corrupts some other memory location -- in case of
arm64 the priv pointer in the same structure.
Since the advertising flags are updated from supported at the end of the
function the incorrect line isn't needed at all and can be removed.
Fixes: a29de52ba2a1 ("net: dp83869: Add ability to advertise Fiber connection")
Signed-off-by: Ingo van Lil <[email protected]>
Reviewed-by: Alexander Sverdlin <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from ieee802154, bluetooth and netfilter.
Current release - regressions:
- eth: mlx5: fix wrong reserved field in hca_cap_2 in mlx5_ifc
- eth: am65-cpsw: fix forever loop in cleanup code
Current release - new code bugs:
- eth: mlx5: HWS, fixed double-free in error flow of creating SQ
Previous releases - regressions:
- core: avoid potential underflow in qdisc_pkt_len_init() with UFO
- core: test for not too small csum_start in virtio_net_hdr_to_skb()
- vrf: revert "vrf: remove unnecessary RCU-bh critical section"
- bluetooth:
- fix uaf in l2cap_connect
- fix possible crash on mgmt_index_removed
- dsa: improve shutdown sequence
- eth: mlx5e: SHAMPO, fix overflow of hd_per_wq
- eth: ip_gre: fix drops of small packets in ipgre_xmit
Previous releases - always broken:
- core: fix gso_features_check to check for both
dev->gso_{ipv4_,}max_size
- core: fix tcp fraglist segmentation after pull from frag_list
- netfilter: nf_tables: prevent nf_skb_duplicated corruption
- sctp: set sk_state back to CLOSED if autobind fails in
sctp_listen_start
- mac802154: fix potential RCU dereference issue in
mac802154_scan_worker
- eth: fec: restart PPS after link state change"
* tag 'net-6.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (48 commits)
sctp: set sk_state back to CLOSED if autobind fails in sctp_listen_start
dt-bindings: net: xlnx,axi-ethernet: Add missing reg minItems
doc: net: napi: Update documentation for napi_schedule_irqoff
net/ncsi: Disable the ncsi work before freeing the associated structure
net: phy: qt2025: Fix warning: unused import DeviceId
gso: fix udp gso fraglist segmentation after pull from frag_list
bridge: mcast: Fail MDB get request on empty entry
vrf: revert "vrf: Remove unnecessary RCU-bh critical section"
net: ethernet: ti: am65-cpsw: Fix forever loop in cleanup code
net: phy: realtek: Check the index value in led_hw_control_get
ppp: do not assume bh is held in ppp_channel_bridge_input()
selftests: rds: move include.sh to TEST_FILES
net: test for not too small csum_start in virtio_net_hdr_to_skb()
net: gso: fix tcp fraglist segmentation after pull from frag_list
ipv4: ip_gre: Fix drops of small packets in ipgre_xmit
net: stmmac: dwmac4: extend timeout for VLAN Tag register busy bit check
net: add more sanity checks to qdisc_pkt_len_init()
net: avoid potential underflow in qdisc_pkt_len_init() with UFO
net: ethernet: ti: cpsw_ale: Fix warning on some platforms
net: microchip: Make FDMA config symbol invisible
...
|
|
Fix the following warning when the driver is compiled as built-in:
warning: unused import: `DeviceId`
--> drivers/net/phy/qt2025.rs:18:5
|
18 | DeviceId, Driver,
| ^^^^^^^^
|
= note: `#[warn(unused_imports)]` on by default
device_table in module_phy_driver macro is defined only when the
driver is built as a module. Use phy::DeviceId in the macro instead of
importing `DeviceId` since `phy` is always used.
Fixes: fd3eaad826da ("net: phy: add Applied Micro QT2025 PHY driver")
Reported-by: kernel test robot <[email protected]>
Closes: https://lore.kernel.org/oe-kbuild-all/[email protected]/
Reviewed-by: Alice Ryhl <[email protected]>
Reviewed-by: Trevor Gross <[email protected]>
Signed-off-by: FUJITA Tomonori <[email protected]>
Reviewed-by: Fiona Behrens <[email protected]>
Acked-by: Miguel Ojeda <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
This reverts commit 504fc6f4f7f681d2a03aa5f68aad549d90eab853.
dev_queue_xmit_nit is expected to be called with BH disabled.
__dev_queue_xmit has the following:
/* Disable soft irqs for various locks below. Also
* stops preemption for RCU.
*/
rcu_read_lock_bh();
VRF must follow this invariant. The referenced commit removed this
protection. Which triggered a lockdep warning:
================================
WARNING: inconsistent lock state
6.11.0 #1 Tainted: G W
--------------------------------
inconsistent {IN-SOFTIRQ-W} -> {SOFTIRQ-ON-W} usage.
btserver/134819 [HC0[0]:SC0[0]:HE1:SE1] takes:
ffff8882da30c118 (rlock-AF_PACKET){+.?.}-{2:2}, at: tpacket_rcv+0x863/0x3b30
{IN-SOFTIRQ-W} state was registered at:
lock_acquire+0x19a/0x4f0
_raw_spin_lock+0x27/0x40
packet_rcv+0xa33/0x1320
__netif_receive_skb_core.constprop.0+0xcb0/0x3a90
__netif_receive_skb_list_core+0x2c9/0x890
netif_receive_skb_list_internal+0x610/0xcc0
[...]
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(rlock-AF_PACKET);
<Interrupt>
lock(rlock-AF_PACKET);
*** DEADLOCK ***
Call Trace:
<TASK>
dump_stack_lvl+0x73/0xa0
mark_lock+0x102e/0x16b0
__lock_acquire+0x9ae/0x6170
lock_acquire+0x19a/0x4f0
_raw_spin_lock+0x27/0x40
tpacket_rcv+0x863/0x3b30
dev_queue_xmit_nit+0x709/0xa40
vrf_finish_direct+0x26e/0x340 [vrf]
vrf_l3_out+0x5f4/0xe80 [vrf]
__ip_local_out+0x51e/0x7a0
[...]
Fixes: 504fc6f4f7f6 ("vrf: Remove unnecessary RCU-bh critical section")
Link: https://lore.kernel.org/netdev/[email protected]/
Reported-by: Ben Greear <[email protected]>
Signed-off-by: Willem de Bruijn <[email protected]>
Cc: [email protected]
Reviewed-by: Ido Schimmel <[email protected]>
Tested-by: Ido Schimmel <[email protected]>
Reviewed-by: David Ahern <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
This error handling has a typo. It should i++ instead of i--. In the
original code the error handling will loop until it crashes.
Fixes: da70d184a8c3 ("net: ethernet: ti: am65-cpsw: Introduce multi queue Rx")
Signed-off-by: Dan Carpenter <[email protected]>
Reviewed-by: Alexander Sverdlin <[email protected]>
Reviewed-by: Roger Quadros <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Just like rtl8211f_led_hw_is_supported() and
rtl8211f_led_hw_control_set(), the rtl8211f_led_hw_control_get() also
needs to check the index value, otherwise the caller is likely to get
an incorrect rules.
Fixes: 17784801d888 ("net: phy: realtek: Add support for PHY LEDs on RTL8211F")
Signed-off-by: Hui Wang <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Networking receive path is usually handled from BH handler.
However, some protocols need to acquire the socket lock, and
packets might be stored in the socket backlog is the socket was
owned by a user process.
In this case, release_sock(), __release_sock(), and sk_backlog_rcv()
might call the sk->sk_backlog_rcv() handler in process context.
sybot caught ppp was not considering this case in
ppp_channel_bridge_input() :
WARNING: inconsistent lock state
6.11.0-rc7-syzkaller-g5f5673607153 #0 Not tainted
--------------------------------
inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
ksoftirqd/1/24 [HC0[0]:SC1[1]:HE1:SE0] takes:
ffff0000db7f11e0 (&pch->downl){+.?.}-{2:2}, at: spin_lock include/linux/spinlock.h:351 [inline]
ffff0000db7f11e0 (&pch->downl){+.?.}-{2:2}, at: ppp_channel_bridge_input drivers/net/ppp/ppp_generic.c:2272 [inline]
ffff0000db7f11e0 (&pch->downl){+.?.}-{2:2}, at: ppp_input+0x16c/0x854 drivers/net/ppp/ppp_generic.c:2304
{SOFTIRQ-ON-W} state was registered at:
lock_acquire+0x240/0x728 kernel/locking/lockdep.c:5759
__raw_spin_lock include/linux/spinlock_api_smp.h:133 [inline]
_raw_spin_lock+0x48/0x60 kernel/locking/spinlock.c:154
spin_lock include/linux/spinlock.h:351 [inline]
ppp_channel_bridge_input drivers/net/ppp/ppp_generic.c:2272 [inline]
ppp_input+0x16c/0x854 drivers/net/ppp/ppp_generic.c:2304
pppoe_rcv_core+0xfc/0x314 drivers/net/ppp/pppoe.c:379
sk_backlog_rcv include/net/sock.h:1111 [inline]
__release_sock+0x1a8/0x3d8 net/core/sock.c:3004
release_sock+0x68/0x1b8 net/core/sock.c:3558
pppoe_sendmsg+0xc8/0x5d8 drivers/net/ppp/pppoe.c:903
sock_sendmsg_nosec net/socket.c:730 [inline]
__sock_sendmsg net/socket.c:745 [inline]
__sys_sendto+0x374/0x4f4 net/socket.c:2204
__do_sys_sendto net/socket.c:2216 [inline]
__se_sys_sendto net/socket.c:2212 [inline]
__arm64_sys_sendto+0xd8/0xf8 net/socket.c:2212
__invoke_syscall arch/arm64/kernel/syscall.c:35 [inline]
invoke_syscall+0x98/0x2b8 arch/arm64/kernel/syscall.c:49
el0_svc_common+0x130/0x23c arch/arm64/kernel/syscall.c:132
do_el0_svc+0x48/0x58 arch/arm64/kernel/syscall.c:151
el0_svc+0x54/0x168 arch/arm64/kernel/entry-common.c:712
el0t_64_sync_handler+0x84/0xfc arch/arm64/kernel/entry-common.c:730
el0t_64_sync+0x190/0x194 arch/arm64/kernel/entry.S:598
irq event stamp: 282914
hardirqs last enabled at (282914): [<ffff80008b42e30c>] __raw_spin_unlock_irqrestore include/linux/spinlock_api_smp.h:151 [inline]
hardirqs last enabled at (282914): [<ffff80008b42e30c>] _raw_spin_unlock_irqrestore+0x38/0x98 kernel/locking/spinlock.c:194
hardirqs last disabled at (282913): [<ffff80008b42e13c>] __raw_spin_lock_irqsave include/linux/spinlock_api_smp.h:108 [inline]
hardirqs last disabled at (282913): [<ffff80008b42e13c>] _raw_spin_lock_irqsave+0x2c/0x7c kernel/locking/spinlock.c:162
softirqs last enabled at (282904): [<ffff8000801f8e88>] softirq_handle_end kernel/softirq.c:400 [inline]
softirqs last enabled at (282904): [<ffff8000801f8e88>] handle_softirqs+0xa3c/0xbfc kernel/softirq.c:582
softirqs last disabled at (282909): [<ffff8000801fbdf8>] run_ksoftirqd+0x70/0x158 kernel/softirq.c:928
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&pch->downl);
<Interrupt>
lock(&pch->downl);
*** DEADLOCK ***
1 lock held by ksoftirqd/1/24:
#0: ffff80008f74dfa0 (rcu_read_lock){....}-{1:2}, at: rcu_lock_acquire+0x10/0x4c include/linux/rcupdate.h:325
stack backtrace:
CPU: 1 UID: 0 PID: 24 Comm: ksoftirqd/1 Not tainted 6.11.0-rc7-syzkaller-g5f5673607153 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 08/06/2024
Call trace:
dump_backtrace+0x1b8/0x1e4 arch/arm64/kernel/stacktrace.c:319
show_stack+0x2c/0x3c arch/arm64/kernel/stacktrace.c:326
__dump_stack lib/dump_stack.c:93 [inline]
dump_stack_lvl+0xe4/0x150 lib/dump_stack.c:119
dump_stack+0x1c/0x28 lib/dump_stack.c:128
print_usage_bug+0x698/0x9ac kernel/locking/lockdep.c:4000
mark_lock_irq+0x980/0xd2c
mark_lock+0x258/0x360 kernel/locking/lockdep.c:4677
__lock_acquire+0xf48/0x779c kernel/locking/lockdep.c:5096
lock_acquire+0x240/0x728 kernel/locking/lockdep.c:5759
__raw_spin_lock include/linux/spinlock_api_smp.h:133 [inline]
_raw_spin_lock+0x48/0x60 kernel/locking/spinlock.c:154
spin_lock include/linux/spinlock.h:351 [inline]
ppp_channel_bridge_input drivers/net/ppp/ppp_generic.c:2272 [inline]
ppp_input+0x16c/0x854 drivers/net/ppp/ppp_generic.c:2304
ppp_async_process+0x98/0x150 drivers/net/ppp/ppp_async.c:495
tasklet_action_common+0x318/0x3f4 kernel/softirq.c:785
tasklet_action+0x68/0x8c kernel/softirq.c:811
handle_softirqs+0x2e4/0xbfc kernel/softirq.c:554
run_ksoftirqd+0x70/0x158 kernel/softirq.c:928
smpboot_thread_fn+0x4b0/0x90c kernel/smpboot.c:164
kthread+0x288/0x310 kernel/kthread.c:389
ret_from_fork+0x10/0x20 arch/arm64/kernel/entry.S:860
Fixes: 4cf476ced45d ("ppp: add PPPIOCBRIDGECHAN and PPPIOCUNBRIDGECHAN ioctls")
Reported-by: [email protected]
Closes: https://lore.kernel.org/netdev/[email protected]/T/#u
Signed-off-by: Eric Dumazet <[email protected]>
Cc: Tom Parkin <[email protected]>
Cc: James Chapman <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 fixes 2024-09-25
* tag 'mlx5-fixes-2024-09-25' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5e: Fix crash caused by calling __xfrm_state_delete() twice
net/mlx5e: SHAMPO, Fix overflow of hd_per_wq
net/mlx5: HWS, changed E2BIG error to a negative return code
net/mlx5: HWS, fixed double-free in error flow of creating SQ
net/mlx5: Fix wrong reserved field in hca_cap_2 in mlx5_ifc
net/mlx5e: Fix NULL deref in mlx5e_tir_builder_alloc()
net/mlx5: Added cond_resched() to crdump collection
net/mlx5: Fix error path in multi-packet WQE transmit
====================
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wpan/wpan
Stefan Schmidt says:
====================
pull-request: ieee802154 for net 2024-09-27
Jinjie Ruan added the use of IRQF_NO_AUTOEN in the mcr20a driver and fixed
and addiotinal build dependency problem while doing so.
Jiawei Ye, ensured a correct RCU handling in mac802154_scan_worker.
* tag 'ieee802154-for-net-2024-09-27' of git://git.kernel.org/pub/scm/linux/kernel/git/wpan/wpan:
net: ieee802154: mcr20a: Use IRQF_NO_AUTOEN flag in request_irq()
mac802154: Fix potential RCU dereference issue in mac802154_scan_worker
ieee802154: Fix build error
====================
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
|
|
Increase the timeout for checking the busy bit of the VLAN Tag register
from 10µs to 500ms. This change is necessary to accommodate scenarios
where Energy Efficient Ethernet (EEE) is enabled.
Overnight testing revealed that when EEE is active, the busy bit can
remain set for up to approximately 300ms. The new 500ms timeout provides
a safety margin.
Fixes: ed64639bc1e0 ("net: stmmac: Add support for VLAN Rx filtering")
Reviewed-by: Andrew Lunn <[email protected]>
Signed-off-by: Shenwei Wang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Paolo Abeni <[email protected]>
|
|
The number of register fields cannot be assumed to be ALE_FIELDS_MAX
as some platforms can have lesser fields.
Solve this by embedding the actual number of fields available
in platform data and use that instead of ALE_FIELDS_MAX.
Gets rid of the below warning on BeagleBone Black
[ 1.007735] WARNING: CPU: 0 PID: 33 at drivers/base/regmap/regmap.c:1208 regmap_field_init+0x88/0x9c
[ 1.007802] invalid empty mask defined
[ 1.007812] Modules linked in:
[ 1.007842] CPU: 0 UID: 0 PID: 33 Comm: kworker/u4:3 Not tainted 6.11.0-01459-g508403ab7b74-dirty #840
[ 1.007867] Hardware name: Generic AM33XX (Flattened Device Tree)
[ 1.007890] Workqueue: events_unbound deferred_probe_work_func
[ 1.007935] Call trace:
[ 1.007957] unwind_backtrace from show_stack+0x10/0x14
[ 1.007999] show_stack from dump_stack_lvl+0x50/0x64
[ 1.008033] dump_stack_lvl from __warn+0x70/0x124
[ 1.008077] __warn from warn_slowpath_fmt+0x194/0x1a8
[ 1.008113] warn_slowpath_fmt from regmap_field_init+0x88/0x9c
[ 1.008154] regmap_field_init from devm_regmap_field_alloc+0x48/0x64
[ 1.008193] devm_regmap_field_alloc from cpsw_ale_create+0xfc/0x320
[ 1.008251] cpsw_ale_create from cpsw_init_common+0x214/0x354
[ 1.008286] cpsw_init_common from cpsw_probe+0x4ac/0xb88
Reported-by: Geert Uytterhoeven <[email protected]>
Closes: https://lore.kernel.org/netdev/CAMuHMdUf-tKRDzkz2_m8qdFTFutefddU0NTratVrEjRTzA3yQQ@mail.gmail.com/
Fixes: 11cbcfeaa79e ("net: ethernet: ti: cpsw_ale: use regfields for number of Entries and Policers")
Signed-off-by: Roger Quadros <[email protected]>
Tested-by: Geert Uytterhoeven <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Paolo Abeni <[email protected]>
|
|
There is no need to ask the user about enabling Microchip FDMA
functionality, as all drivers that use it select the FDMA symbol.
Hence make the symbol invisible, unless when compile-testing.
Fixes: 30e48a75df9c6ead ("net: microchip: add FDMA library")
Signed-off-by: Geert Uytterhoeven <[email protected]>
Reviewed-by: Daniel Machon <[email protected]>
Link: https://patch.msgid.link/8e2bcd8899c417a962b7ee3f75b29f35b25d7933.1727171879.git.geert+renesas@glider.be
Signed-off-by: Paolo Abeni <[email protected]>
|
|
On link-state change, the controller gets reset,
which clears all PTP registers, including PHC time,
calibrated clock correction values etc. For correct
IEEE 1588 operation we need to restore these after
the reset.
Fixes: 6605b730c061 ("FEC: Add time stamping code and a PTP hardware clock")
Signed-off-by: Csókás, Bence <[email protected]>
Reviewed-by: Wei Fang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Paolo Abeni <[email protected]>
|
|
On link state change, the controller gets reset,
causing PPS to drop out. Re-enable PPS if it was
enabled before the controller reset.
Fixes: 6605b730c061 ("FEC: Add time stamping code and a PTP hardware clock")
Signed-off-by: Csókás, Bence <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Paolo Abeni <[email protected]>
|
|
The value is read from the register TXGBE_RX_GEN_CTL3, and it should be
written back to TXGBE_RX_GEN_CTL3 when it changes some fields.
Cc: [email protected]
Fixes: f629acc6f210 ("net: pcs: xpcs: support to switch mode for Wangxun NICs")
Signed-off-by: Jiawen Wu <[email protected]>
Reported-by: Russell King (Oracle) <[email protected]>
Reviewed-by: Russell King (Oracle) <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Paolo Abeni <[email protected]>
|