| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
After recent change we started returning 0 from
ndo_get_phys_port_name for VFs. The name parameter for
ndo_get_phys_port_name is not initialized by the stack so
this can lead to a crash. We should have kept returning
-EOPNOTSUPP in the first place.
Signed-off-by: Jakub Kicinski <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5e-updates-2018-05-25
This series includes updates for mlx5e netdev driver.
1) Allowr flow based VF vport mirroring under sriov switchdev scheme,
added support for offloading the TC mirred mirror sub-action, from
Chris Mi.
=================
From: Or Gerlitz <[email protected]>
The user will typically set the actions order such that the mirror
port (mirror VF) sees packets as the original port (VF under
mirroring) sent them or as it will receive them. In the general case,
it means that packets are potentially sent to the mirror port before
or after some actions were applied on them.
To properly do that, we follow on the exact action order as set for
the flow and make sure this will also be the case when we program the
HW offload.
If all the actions should apply before forwarding to the mirror and dest port,
mirroring is just multicasting to the two vports. Otherwise, we split
the TC flow to two HW rules, where the 1st applies only the actions
needed up to the mirror (if there are such) and the 2nd the rest of
the actions plus the forwarding to the dest vport.
=================
2) Move to order-0 only allocations (using fragmented work queues) for all
work queues used by the driver, RX and TX descriptor rings
(RQs, SQs and Completion Queues (CQs)), from Tariq Toukan.
3) Avoid resetting netdevice statistics on netdevice
state changes, from Eran Ben Elisha.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
Recently we have switched the csr addresses and values configuration
from a single configuration to all devices to a per-device configuration.
Doing that, the configuration for 6300 devices wasn't set.
This missing definition introduced a kernel panic once trying to access
the csr's.
Add the missing 6300 csr configuration.
While at it, add a checker that the csr values were indeed
configured, and bail out more gracefully if not.
Fixes: a8cbb46f831d ("iwlwifi: allow different csr flags for different device families")
Signed-off-by: Golan Ben Ami <[email protected]>
Signed-off-by: Luca Coelho <[email protected]>
|
|
When there are 16 or more logical CPUs, we request for
`IWL_MAX_RX_HW_QUEUES` (16) IRQs only as we limit to that number of
IRQs, but later on we compare the number of IRQs returned to
nr_online_cpus+2 instead of max_irqs, the latter being what we
actually asked for. This ends up setting num_rx_queues to 17 which
causes lots of out-of-bounds array accesses later on.
Compare to max_irqs instead, and also add an assertion in case
num_rx_queues > IWM_MAX_RX_HW_QUEUES.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=199551
Fixes: 2e5d4a8f61dc ("iwlwifi: pcie: Add new configuration to enable MSIX")
Signed-off-by: Hao Wei Tee <[email protected]>
Tested-by: Sara Sharon <[email protected]>
Signed-off-by: Luca Coelho <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
|
|
This reverts commit fb47ada8dc3c30c8e7b415da155742b49536c61e.
In some situations when we set TXOP_BACKOFF, the probe frame is
not sent at all. What it worse then sending probe frame as part
of AMPDU and can degrade 11n performance to 11g rates.
Cc: [email protected]
Signed-off-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
|
|
Remove and refactor some code in order to avoid having identical code
for different branches.
Notice that the logic has been there since 2014.
Addresses-Coverity-ID: 1426199 ("Identical code for different branches")
Signed-off-by: Gustavo A. R. Silva <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
|
|
Active scan is not allowed on radar channel, instead
using passvie scan with more time.
Signed-off-by: Xinming Hu <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
|
|
Signed-off-by: Xinming Hu <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
|
|
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
|
|
If firmware does not support embedded supplicant, then it in turn
will not support GT rekey offloading. If this is the case, then
driver must not advertise WOWLAN flags related to GTK rekey and
it must also skip sending the GT_REKEY_OFFLOAD_CFG command.
Signed-off-by: Shrenik Shikhare <[email protected]>
Signed-off-by: Cathy Luo <[email protected]>
Signed-off-by: Ganapathi Bhat <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
|
|
Race condition is observed during rmmod of mwifiex_usb:
1. The rmmod thread will call mwifiex_usb_disconnect(), download
SHUTDOWN command and do wait_event_interruptible_timeout(),
waiting for response.
2. The main thread will handle the response and will do a
wake_up_interruptible(), unblocking rmmod thread.
3. On getting unblocked, rmmod thread will make rx_cmd.urb = NULL in
mwifiex_usb_free().
4. The main thread will try to resubmit rx_cmd.urb in
mwifiex_usb_submit_rx_urb(), which is NULL.
To fix, wait for main thread to complete before calling
mwifiex_usb_free().
Signed-off-by: Ganapathi Bhat <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
|
|
This is a follow-up patch for commit 21c5c83ce833
("mwifiex: support sysfs initiated device coredump").
Let us avoid exporting mwifiex_send_cmd and instead use a utility
function mwifiex_fw_dump_event to achive the work.
Signed-off-by: Ganapathi Bhat <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
|
|
Trivial fix to spelling mistake in rsi_dbg message text
Signed-off-by: Colin Ian King <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
|
|
the wl pointer can be null In case only wlcore_sdio is probed while
no WiLink module is successfully probed, as in the case of mounting a
wl12xx module while using a device tree file configured with wl18xx
related settings.
In this case the system was crashing in wl1271_suspend() as platform
device data is not set.
Make sure wl the pointer is valid before using it.
Signed-off-by: Eyal Reizer <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
|
|
add pci_disable_device in error handling while init_atmel_card failed.
Signed-off-by: YueHaibing <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
|
|
In former patch, I enqueu all C2H commands and processed by a workqueue.
In case C2H_BT_INFO will issue a H2C command to set BT reg, and wait for
a C2H ack. But it is totally impossible that C2H workqueue waits for a
C2H command, so kernel log warn
rtlwifi: :<0> btmpinfo wait (req_num=0) timeout
Since the C2H ack command C2H_BT_MP can be safely processed in interrupt
context, add a fast command path to deal with the command.
Signed-off-by: Ping-Ke Shih <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
|
|
The format of C2H data is ID(1 byte) + Length(1 byte) + value, and it is
more readable to use macros to access C2H data.
Signed-off-by: Ping-Ke Shih <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
|
|
We use 'struct rtl_c2hcmd' to store C2H commands originally, and the code
is slightly complex to enqueue and dequeue and also wastes time to
allocate and memcpy data. Since C2H commands are asynchronous events,
they can be processed in work queue, so RX ISR enqueues C2H result in
removal of rtl_c2h_packet_handler().
Signed-off-by: Ping-Ke Shih <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
|
|
Similar to rx_command_packet, we can call rtl_c2h_content_parsing so the
hal_op isn't necessary.
Signed-off-by: Ping-Ke Shih <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
|
|
Because the hal_op rx_command_packet does C2H handler if rx packet type
is C2H, and the handler have been moved to base.c so we can call the
handler directly.
Signed-off-by: Ping-Ke Shih <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
|
|
Merge duplicate C2H handler and implement the handler in base.c.
Signed-off-by: Ping-Ke Shih <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
|
|
We're going to merge C2H handler into one, but one special case is to
handle RA_REPORT that implements in individual IC folder. So this commit
adds a hal_op for caller in common code.
Signed-off-by: Ping-Ke Shih <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
|
|
The caller of hal_op rx_command_packet will assert function pointer
before calling, so we can remove dummy functions safely.
Signed-off-by: Ping-Ke Shih <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
|
|
The IDs are defined by driver and map to the fw C2H IDs, but they aren't
used now result in removal.
Signed-off-by: Ping-Ke Shih <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
|
|
Move C2H definition to wifi.h, because the definitions of 8192ee, 8723be
and 8821ae are the same.
Signed-off-by: Ping-Ke Shih <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
|
|
Current chips use packet-based C2H commands whose IDs differ from old
ones, so this commit simply gives C2H_V0_ as prefix of command IDs.
Signed-off-by: Ping-Ke Shih <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
|
|
Move duplicate definitions from def.h of ic folder to wifi.h
Signed-off-by: Ping-Ke Shih <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
|
|
To use keep-alive mechanism in mac80211 stack, since driver supports
reporting accurate nullfunc frame tx ack now.
Signed-off-by: Tzu-En Huang <[email protected]>
Signed-off-by: Ping-Ke Shih <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
|
|
In order to realize the keep-alive mechanism in mac80211 stack, reporting
accurate tx ack status for nullfunc frame is added in this commit.
If current frame is nullfunc frame, we ask firmware to report by filling
TX report bit in TX descriptor. After this frame DMA done, TX interrupt is
triggered but TX status is unknown at this moment, so enqueue this skb
into tx_report->queue. Finally, C2H report will be received if the frame
is transmitted successfully or retried over, and then we report to mac80211
with IEEE80211_TX_STAT_ACK flag only if it's successful. Otherwise, if
failure or timeout (one second), we report to mac80211 without this flag.
Signed-off-by: Tzu-En Huang <[email protected]>
Signed-off-by: Ping-Ke Shih <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
|
|
We can have pm_runtime_get_sync() return 1, and we can have
pm_runtime_put_sync() return -EBUSY. See rpm_suspend() and
rpm_resume() for more information.
Fix the issue by returning 0 from wl12xx_sdio_power_on() on success.
And use pm_runtime_put() instead of pm_runtime_put_sync() for
wl12xx_sdio_power_off(), then the MMC subsystem will idle the bus
when suitable.
Otherwise wlcore can sometimes get confused and may report bogus
errors and WLAN connection can fail.
Note that while wlcore checks the return value for wl1271_power_on(),
the return value is ignored for wl1271_power_off(). Let's fix them
both though to avoid further confusion in the future.
Fixes: 60f36637bbbd ("wlcore: sdio: allow pm to handle sdio power")
Signed-off-by: Tony Lindgren <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
|
|
When register a RoCE client with hnae3vf device, it needs to judge
the device whether support RoCE vf function. Otherwise, it will
lead to calltrace when RoCE is not support vf function and remove
roce device.
The calltrace as follows:
[ 93.156614] Unable to handle kernel NULL pointer dereference at virtual address 00000015
<SNIP>
[ 93.278784] Call trace:
[ 93.278788] hnae3_match_n_instantiate+0x24/0xd8 [hnae3]
[ 93.278790] hnae3_register_client+0xcc/0x150 [hnae3]
[ 93.278801] hns_roce_hw_v2_init+0x18/0x1000 [hns_roce_hw_v2]
[ 93.278805] do_one_initcall+0x58/0x160
[ 93.278807] do_init_module+0x64/0x1d8
[ 93.278809] load_module+0x135c/0x15c8
[ 93.278811] SyS_finit_module+0x100/0x118
[ 93.278816] __sys_trace_return+0x0/0x4
[ 93.278827] Code: aa0003f5 12001c56 aa1e03e0 d503201f (b9402660)
Fixes: e2cb1dec9779 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Reported-by: Xinwei Kong <[email protected]>
Reported-by: Zhou Wang <[email protected]>
Signed-off-by: Lijun Ou <[email protected]>
Signed-off-by: Zhou Wang <[email protected]>
Signed-off-by: Salil Mehta <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Firmware now supports control of all leds. Existing HNS3 driver code
only supported led locate command over SFP Fibre ports. But now it
is also supported over copper port.
This patch removes existing not needed code for the led locate
command and updates the led control command between driver and
firmware.
Signed-off-by: Jian Shen <[email protected]>
Signed-off-by: Peng Li <[email protected]>
Signed-off-by: Salil Mehta <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
In the previous implementation of led control for fibre port , parses the
port speed configuration, checks the link status and traffic status per
second, and updates the blink status of link led, traffic led and speed
led.
Now, the firmware takes responsibility to handle the led, the dirver just
needs to deal with locate command.
So the codes for link led, traffic led and speed led are useless now. This
patch removes these redundant codes.
Signed-off-by: Jian Shen <[email protected]>
Signed-off-by: Peng Li <[email protected]>
Signed-off-by: Salil Mehta <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
When we down the port, some packets are left in TX/RX buffer. When we
up the port again, these old packets are forwarded to protocol stack
or are sent to internet. It will make some problem. TX/RX buffer should
be cleared when stopping port. This patch adds some function to ensure
the buffer is clean when port is started. We should clear the rings
when clients are being un-initialized as well.
Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Fuyun Liang <[email protected]>
Signed-off-by: Peng Li <[email protected]>
Signed-off-by: Salil Mehta <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Our code will ensure that hns3_clear_tx_ring is not used to cleared
RX rings and hns3_clear_rx_ring is not used to cleared TX rings. So
the ring type check is unnecessary.
Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Fuyun Liang <[email protected]>
Signed-off-by: Peng Li <[email protected]>
Signed-off-by: Salil Mehta <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
RX Buffer Descriptor contains a VALID bit which indicates if the BD
is valid and has some data. This field is set by HNS3 hardware to
intimate the driver of some valid data present in the BD. nd should
be reset by the driver when BD is being used again. In the existing
code this bit was not being (re-)initialized properly and hence was
causing problems.
Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Fuyun Liang <[email protected]>
Signed-off-by: Peng Li <[email protected]>
Signed-off-by: Salil Mehta <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
HNAE3 module supports kernel nic driver, user nic driver and roce driver,
and there are 3 client types. Driver uses one bit(HNAE3_CLIENT_INITED_B)
to indicate the client initialization state, it will cause confusion
for 3 client types. This patch fixes it by use 3 bits to indicate the
initialization state.
Fixes: 38caee9d3ee8 ("net: hns3: Add support of the HNAE3 framework")
Signed-off-by: Peng Li <[email protected]>
Signed-off-by: Salil Mehta <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Before the firmware updates the crq's tail pointer, if the PF driver
reads the data in the crq, the data may be incomplete at this time,
which will lead to the driver read an unknown message.
This patch fixes it by checking if crq is not empty before reading the
message.
Fixes: c1a81619d73a ("net: hns3: Add mailbox interrupt handling to PF driver")
Signed-off-by: Xi Wang <[email protected]>
Signed-off-by: Peng Li <[email protected]>
Signed-off-by: Salil Mehta <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
HCLGE_PROMISC_TX_EN_B and HCLGE_PROMISC_RX_EN_B are not supported
on pdev revision(0x20), new revision(0x21) supports them.
Signed-off-by: Peng Li <[email protected]>
Signed-off-by: Salil Mehta <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Hardware Revision(0x21) Buffer Descriptor adds a field STRP_TAGP
for vlan stripped processed indication. STRP_TAGP field has 2 bits,
bit 0 is stripped indication of the vlan tag in outer vlan tag
field, bit 1 is stripped indication of the vlan tag in inner vlan
tag field. For each bit, 0 indicates the tag is not stripped and
1 indicates the tag is stripped.
This patch adds STRP_TAGP support for revision(0x21), and does not
change the revision(0x20) action.
Signed-off-by: Peng Li <[email protected]>
Signed-off-by: Salil Mehta <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
HNS3 Hardware can support up to two VLAN tags in transmit leg, the PPP
module can handle the packets based on the tag1 and tag2 config. This
patch adds support for tag2 config for vlan handling
Signed-off-by: Peng Li <[email protected]>
Signed-off-by: Salil Mehta <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
In the latest revision of the hardware, if a packet is spanning
across multiple BDs then only VLD bit and current data size info
is valid in each BD, and rest of the information is only valid
in the last BD of the packet. In such case we should make sure
we are fetching RX packet size from the first descriptor and
information like VLAN should be fetched from last BD.
Signed-off-by: Peng Li <[email protected]>
Reviewed-by: Yisen Zhuang <[email protected]>
Signed-off-by: Salil Mehta <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
SIMCOM are reusing a single device ID for many (all of their?)
different modems, based on different chipsets and firmwares. Newer
Qualcomm chipset generations require setting DTR to wake the QMI
function. The SIM7600E modem is using such a chipset, making it
fail to work with this driver despite the device ID match.
Fix by unconditionally enabling the SET_DTR quirk for all SIMCOM
modems using this specific device ID. This is similar to what
we already have done for another case of device IDs recycled over
multiple chipset generations: 14cf4a771b30 ("drivers: net: usb:
qmi_wwan: add QMI_QUIRK_SET_DTR for Telit PID 0x1201")
Initial testing on an older SIM7100 modem shows no immediate side
effects.
Reported-by: Sebastian Sjoholm <[email protected]>
Cc: Reinhard Speyerer <[email protected]>
Signed-off-by: Bjørn Mork <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The netsec network controller IP can drive 64 address bits for DMA, and
the DMA mask is set accordingly in the driver. However, the SynQuacer
SoC, which is the only silicon incorporating this IP at the moment,
integrates this IP in a manner that leaves address bits [63:40]
unconnected.
Up until now, this has not resulted in any problems, given that the DDR
controller doesn't decode those bits to begin with. However, recent
firmware updates for platforms incorporating this SoC allow the IOMMU
to be enabled, which does decode address bits [47:40], and allocates
top down from the IOVA space, producing DMA addresses that have bits
set that have been left unconnected.
Both the DT and ACPI (IORT) descriptions of the platform take this into
account, and only describe a DMA address space of 40 bits (using either
dma-ranges DT properties, or DMA address limits in IORT named component
nodes). However, even though our IOMMU and bus layers may take such
limitations into account by setting a narrower DMA mask when creating
the platform device, the netsec probe() entrypoint follows the common
practice of setting the DMA mask uncondionally, according to the
capabilities of the IP block itself rather than to its integration into
the chip.
It is currently unclear what the correct fix is here. We could hack around
it by only setting the DMA mask if it deviates from its default value of
DMA_BIT_MASK(32). However, this makes it impossible for the bus layer to
use DMA_BIT_MASK(32) as the bus limit, and so it appears that a more
comprehensive approach is required to take DMA limits imposed by the
SoC as a whole into account.
In the mean time, let's limit the DMA mask to 40 bits. Given that there
is currently only one SoC that incorporates this IP, this is a reasonable
approach that can be backported to -stable and buys us some time to come
up with a proper fix going forward.
Fixes: 533dd11a12f6 ("net: socionext: Add Synquacer NetSec driver")
Cc: Robin Murphy <[email protected]>
Cc: Jassi Brar <[email protected]>
Cc: Masahisa Kojima <[email protected]>
Cc: Ilias Apalodimas <[email protected]>
Signed-off-by: Ard Biesheuvel <[email protected]>
Reviewed-by: Robin Murphy <[email protected]>
Acked-by: Jassi Brar <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Manage dwmac-4.20a version from synopsys
Signed-off-by: Christophe Roullier <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Glue codes to support stm32mp157c device and stay
compatible with stm32 mcu familly
Signed-off-by: Christophe Roullier <[email protected]>
Acked-by: Alexandre TORGUE <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Global variable gfar_phc_index was used to get and store
phc index through gianfar_ptp driver. However gianfar_ptp
had been renamed as ptp_qoriq for QorIQ common PTP driver.
This gfar_phc_index doesn't work any more, and the phc index
is stored in drvdata now. This patch is to support getting
phc index through ptp_qoriq drvdata.
Signed-off-by: Yangbo Lu <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
gianfar_ptp was the PTP clock driver for 1588 timer
module of Freescale QorIQ eTSEC (Enhanced Three-Speed
Ethernet Controllers) platforms. Actually QorIQ DPAA
(Data Path Acceleration Architecture) platforms is
also using the same 1588 timer module in hardware.
This patch is to rework gianfar_ptp as QorIQ common
PTP driver to support both DPAA and eTSEC. Moved
gianfar_ptp.c to drivers/ptp/, renamed it as
ptp_qoriq.c, and renamed many variables. There were
not any function changes.
Signed-off-by: Yangbo Lu <[email protected]>
Acked-by: Richard Cochran <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Fixup the checksum for CHECKSUM_COMPLETE when pulling skbs on RX path.
Otherwise we get splats when tc mirred is used to redirect packets to ifb.
Before fix:
nic: hw csum failure
Signed-off-by: Jon Maxwell <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Add RTL8211B suspend / resume callbacks.
Signed-off-by: Heiner Kallweit <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|