aboutsummaryrefslogtreecommitdiff
path: root/drivers/net
AgeCommit message (Collapse)AuthorFilesLines
2016-07-18wlcore/wl18xx: mesh: added initial mesh support for wl8Maital Hahn7-14/+52
1. Added support for interface and role of mesh type. 2. Enabled enable/start of mesh-point role, and opening and closing a connection with a mesh peer. 3. Added multirole combination of mesh and ap under the same limits of dual ap mode. 4. Add support for 'sta_rc_update' opcode for mesh IF. The 'sta_rc_update' opcode is being used in mesh_plink.c. Add support in wlcore to handle this opcode correctly for mesh (as opposed to current implementation that handles STA only). 5. Bumped the firmware version to support new Mesh functionality Signed-off-by: Maital Hahn <maitalm@ti.com> Signed-off-by: Yaniv Machani <yanivma@ti.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2016-07-18mwifiex: Reduce endian conversion for REG Host CommandsPrasun Maiti4-50/+46
For multiple REG Host Commands (e.g HostCmd_CMD_802_11_EEPROM_ACCESS, HostCmd_CMD_MAC_REG_ACCESS etc.) "cpu_to_leX"-converted values are saved to driver. So, "leX_to_cpu" conversion is required too many times afterwards in driver. This patch reduces the endian: conversion without saving "cpu_to_leX" converted values in driver. This will convert endianness in prepare command and command response path. Signed-off-by: Prasun Maiti <prasunmaiti87@gmail.com> Acked-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2016-07-17net: ethernet: marvell: pxa168_eth: use phy_ethtool_{get|set}_link_ksettingsPhilippe Reynes1-21/+18
There are two generics functions phy_ethtool_{get|set}_link_ksettings, so we can use them instead of defining the same code in the driver. Signed-off-by: Philippe Reynes <tremyfr@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-17net: ethernet: marvell: pxa168_eth: use phydev from struct net_devicePhilippe Reynes1-20/+16
The private structure contain a pointer to phydev, but the structure net_device already contain such pointer. So we can remove the pointer phydev in the private structure, and update the driver to use the one contained in struct net_device. Signed-off-by: Philippe Reynes <tremyfr@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-17net: ethernet: adi: bfin_mac: use phy_ethtool_{get|set}_link_ksettingsPhilippe Reynes1-23/+2
There are two generics functions phy_ethtool_{get|set}_link_ksettings, so we can use them instead of defining the same code in the driver. There was a check on CAP_NET_ADMIN in bfin_mac_ethtool_setsettings, but this check is already done in dev_ethtool, so no need to repeat it before calling the generic function. Signed-off-by: Philippe Reynes <tremyfr@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-17net: ethernet: adi: bfin_mac: use phydev from struct net_devicePhilippe Reynes2-20/+12
The private structure contain a pointer to phydev, but the structure net_device already contain such pointer. So we can remove the pointer phydev in the private structure, and update the driver to use the one contained in struct net_device. Signed-off-by: Philippe Reynes <tremyfr@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-17dwc_eth_qos: Remove deprecated create_singlethread_workqueueBhaktipriya Shridhar1-1/+2
alloc_workqueue replaces deprecated create_singlethread_workqueue(). A dedicated workqueue has been used since the workitem viz lp->txtimeout_reinit is involved in reinitialization if a TX timeout occurs, which is necessary to guarantee forward progress in packet processing. As a network device can be used during memory reclaim, the workqueue needs forward progress guarantee under memory pressure. WQ_MEM_RECLAIM has been set to ensure this. Since there is only a single work item, explicit concurrency limit is unnecessary here. Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-16net: usb: ax88172x: use phy_ethtool_{get|set}_link_ksettingsPhilippe Reynes1-20/+2
There are two generics functions phy_ethtool_{get|set}_link_ksettings, so we can use them instead of defining the same code in the driver. Signed-off-by: Philippe Reynes <tremyfr@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-16net: hisilicon: Add Fast Ethernet MAC driverDongpo Li3-0/+1020
This patch adds the Hisilicon Fast Ethernet MAC(FEMAC) driver. The FEMAC supports max speed 100Mbps and has been used in many Hisilicon SoC. Signed-off-by: Dongpo Li <lidongpo@hisilicon.com> Reviewed-by: Jiancheng Xue <xuejiancheng@hisilicon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-16net: Add MDIO bus driver for the Hisilicon FEMACDongpo Li3-0/+174
This patch adds a separate driver for the MDIO interface of the Hisilicon Fast Ethernet MAC. Signed-off-by: Dongpo Li <lidongpo@hisilicon.com> Reviewed-by: Jiancheng Xue <xuejiancheng@hisilicon.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-16net: cpsw: make TI_CPSW_PHY_SEL invisibleUwe Kleine-König1-2/+1
TI_CPSW_PHY_SEL depended on TI_CPSW and was selected by the latter. So there is no reason to have this symbol visible. A further optimisation would be to put the code for both symbols into a single module which would allow to not export at least cpsw_phy_sel() and simplify the module load process. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-16wan/fsl_ucc_hdlc: rewrite error handling to make it clearerZhao Qiang1-28/+27
It was used err_xxx for labeled statement, it is not easy to understand, now use free_xxx for labeled statement. Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-16wan/fsl_ucc_hdlc: remove reduplicative freed memory 'uhdlc_priv'Zhao Qiang1-1/+0
'uhdlc_priv' has freed twice, drop the first one. Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-16rndis_host: Set valid random MAC on buggy devicesKristian Evensen1-1/+5
Some devices of the same type all export the same, random MAC address. This behavior has been seen on the ZTE MF910, MF823 and MF831, and there are probably more devices out there. Fix this by generating a valid random MAC address if we read a random MAC from device. Also, changed the memcpy() to ether_addr_copy(), as pointed out by checkpatch. Suggested-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-15net: ethernet: ti: cpmac: use phy_ethtool_{get|set}_link_ksettingsPhilippe Reynes1-21/+2
There are two generics functions phy_ethtool_{get|set}_link_ksettings, so we can use them instead of defining the same code in the driver. There was a check on CAP_NET_ADMIN in cpmac_set_settings, but this check is already done in dev_ethtool, so no need to repeat it before calling the generic function. Signed-off-by: Philippe Reynes <tremyfr@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-15net: ethernet: ti: cpmac: use phydev from struct net_devicePhilippe Reynes1-26/+20
The private structure contain a pointer to phydev, but the structure net_device already contain such pointer. So we can remove the pointer phy in the private structure, and update the driver to use the one contained in struct net_device. Signed-off-by: Philippe Reynes <tremyfr@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-15net: ethernet: amd: au1000_eth: use phy_ethtool_{get|set}_link_ksettingsPhilippe Reynes1-21/+2
There are two generics functions phy_ethtool_{get|set}_link_ksettings, so we can use them instead of defining the same code in the driver. There was a check on CAP_NET_ADMIN in au1000_set_settings, but this check is already done in dev_ethtool, so no need to repeat it before calling the generic function. Signed-off-by: Philippe Reynes <tremyfr@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-15net: ethernet: amd: au1000_eth: use phydev from struct net_devicePhilippe Reynes2-25/+16
The private structure contain a pointer to phydev, but the structure net_device already contain such pointer. So we can remove the pointer phydev in the private structure, and update the driver to use the one contained in struct net_device. Signed-off-by: Philippe Reynes <tremyfr@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-15net: ethernet: smsc9420: use phy_ethtool_{get|set}_link_ksettingsPhilippe Reynes1-22/+2
There are two generics functions phy_ethtool_{get|set}_link_ksettings, so we can use them instead of defining the same code in the driver. Signed-off-by: Philippe Reynes <tremyfr@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-15net: ethernet: smsc9420: use phydev from struct net_devicePhilippe Reynes1-27/+17
The private structure contain a pointer to phydev, but the structure net_device already contain such pointer. So we can remove the pointer phy in the private structure, and update the driver to use the one contained in struct net_device. Signed-off-by: Philippe Reynes <tremyfr@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-15net: ethernet: ethoc: use phy_ethtool_{get|set}_link_ksettingsPhilippe Reynes1-22/+2
There are two generics functions phy_ethtool_{get|set}_link_ksettings, so we can use them instead of defining the same code in the driver. Signed-off-by: Philippe Reynes <tremyfr@gmail.com> Reviewed-by: Tobias Klauser <tklauser@distanz.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-15net: ethernet: ethoc: use phydev from struct net_devicePhilippe Reynes1-13/+7
The private structure contain a pointer to phydev, but the structure net_device already contain such pointer. So we can remove the pointer phy in the private structure, and update the driver to use the one contained in struct net_device. Signed-off-by: Philippe Reynes <tremyfr@gmail.com> Reviewed-by: Tobias Klauser <tklauser@distanz.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-15net: ethernet: pasemi_mac: use phy_ethtool_{get|set}_link_ksettingsPhilippe Reynes1-26/+2
There are two generics functions phy_ethtool_{get|set}_link_ksettings, so we can use them instead of defining the same code in the driver. Signed-off-by: Philippe Reynes <tremyfr@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-15net: ethernet: pasemi_mac: use phydev from struct net_devicePhilippe Reynes3-20/+15
The private structure contain a pointer to phydev, but the structure net_device already contain such pointer. So we can remove the pointer phy in the private structure, and update the driver to use the one contained in struct net_device. Signed-off-by: Philippe Reynes <tremyfr@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-15net: ethernet: xilinx: axienet: use phy_ethtool_{get|set}_link_ksettingsPhilippe Reynes1-45/+2
There are two generics functions phy_ethtool_{get|set}_link_ksettings, so we can use them instead of defining the same code in the driver. Signed-off-by: Philippe Reynes <tremyfr@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-15net: ethernet: xilinx: axienet: use phydev from struct net_devicePhilippe Reynes2-21/+16
The private structure contain a pointer to phydev, but the structure net_device already contain such pointer. So we can remove the pointer phy in the private structure, and update the driver to use the one contained in struct net_device. Signed-off-by: Philippe Reynes <tremyfr@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-15net: ethernet: tc35815: use phy_ethtool_{get|set}_link_ksettingsPhilippe Reynes1-16/+2
There are two generics functions phy_ethtool_{get|set}_link_ksettings, so we can use them instead of defining the same code in the driver. Signed-off-by: Philippe Reynes <tremyfr@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-15net: ethernet: tc35815: use phydev from struct net_devicePhilippe Reynes1-27/+18
The private structure contain a pointer to phydev, but the structure net_device already contain such pointer. So we can remove the pointer phy in the private structure, and update the driver to use the one contained in struct net_device. Signed-off-by: Philippe Reynes <tremyfr@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-15macvtap: switch to use skb arrayJason Wang1-11/+71
This patch switch to use skb array instead of sk_receive_queue to avoid spinlock contentions. Tests shows about 21% improvements for guest rx pps: Before: 1472731 pkts/s After: 1786289 pkts/s Signed-off-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-15macvtap: avoid hash calculating for single queueJason Wang1-0/+4
We decide the rxq through calculating its hash which is not necessary if we only have one rx queue. So this patch skip this and just return queue 0. Test shows 22% improving on guest rx pps. Before: 1201504 pkts/s After: 1472731 pkts/s Signed-off-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-15net: phy: micrel: Add KSZ8041FTL fiber mode supportPhilipp Zabel1-2/+32
We can't detect the FXEN (fiber mode) bootstrap pin, so configure it via a boolean device tree property "micrel,fiber-mode". If it is enabled, auto-negotiation is not supported. The only available modes are 100base-fx (full duplex and half duplex). Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-15wan/fsl_ucc_hdlc: info leak in uhdlc_ioctl()Dan Carpenter1-2/+1
There is a 2 byte struct whole after line.loopback so we need to clear that out to avoid disclosing stack information. Fixes: c19b6d246a35 ('drivers/net: support hdlc function for QE-UCC') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-14mlxsw: spectrum_router: Return -ENOENT in case of errorChristophe Jaillet1-1/+1
'vr' should be a valid pointer here, so returning 'PTR_ERR(vr)' is wrong. Return an explicit error code (-ENOENT) instead. Fixes: 61c503f976 ("mlxsw: spectrum_router: Implement fib4 add/del switchdev obj ops") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-14net: ethernet: ll_temac: use phy_ethtool_{get|set}_link_ksettingsPhilippe Reynes1-12/+2
There are two generics functions phy_ethtool_{get|set}_link_ksettings, so we can use them instead of defining the same code in the driver. Signed-off-by: Philippe Reynes <tremyfr@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-14net: ethernet: ll_temac: use phydev from struct net_devicePhilippe Reynes2-22/+16
The private structure contain a pointer to phydev, but the structure net_device already contain such pointer. So we can remove the pointer phy in the private structure, and update the driver to use the one contained in struct net_device. Signed-off-by: Philippe Reynes <tremyfr@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-14Merge tag 'wireless-drivers-next-for-davem-2016-07-13' of ↵David S. Miller161-1962/+3670
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next Kalle Valo says: ==================== wireless-drivers-next patches for 4.8 Major changes: iwlwifi * more work on the RX path for the 9000 device series * some more dynamic queue allocation work * SAR BIOS implementation * some work on debugging capabilities * added support for GCMP encryption * data path rework in preparation for new HW * some cleanup to remove transport dependency on mac80211 * support for MSIx in preparation for new HW * lots of work in preparation for HW support (9000 and a000 series) mwifiex * implement get_tx_power and get_antenna cfg80211 operation callbacks wl18xx * add support for 64bit clock rtl8xxxu * aggregation support (optional for now) Also wireless-drivers is merged to fix some conflicts. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-14net/mlx5e: Add TC offload support for the VF representors netdeviceOr Gerlitz1-1/+34
The VF representors support only TC filter/action offloads (not mqprio) and this is enabled for them by default. Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-14net/mlx5e: Add TC HW support for FDB (SRIOV e-switch) offloadsOr Gerlitz2-6/+34
Enhance the TC offload code such that when the eswitch exists and it's mode being SRIOV offloads, we do TC actions parsing and setup targeted for eswitch. Next, we add the offloaded flow to the HW e-switch (fdb). Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-14net/mlx5e: Add TC drop and mirred/redirect action parsing for SRIOV offloadsOr Gerlitz1-0/+53
Add the setup code that parses the TC actions needed to support offloading drop and mirred/redirect for SRIOV e-switch. We can redirect between two devices if they belong to the same HW switch, compare the switchdev HW ID attribute to enforce that. Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-14net/mlx5e: Adjustments in the TC offload code towards reuse for SRIOVOr Gerlitz1-16/+16
Towards reusing the TC offloads code for an SRIOV use-case, change some of the helper functions to have _nic in their names so it's clear what's NIC unique and what's general. Also group together the NIC related helpers so we can easily branch per the use-case in downstream patch. Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-14net/mlx5: E-Switch, Add API to configure rules for the offloaded modeOr Gerlitz2-0/+49
This allows for upper levels in the driver, e.g the TC offload code to add e-switch offloaded steering rules. The caller provides the rule spec for matching, action, source and destination vports. Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-14net/mlx5: E-Switch, Use two priorities for SRIOV offloads modeOr Gerlitz3-15/+42
In the offloads mode, some slow path rules are added by the driver (e.g send-to-vport), while offloaded rules are to be added from upper layers. The slow path rules have lower priority and we don't want matching on offloaded rules to suffer from extra steering hops related to the slow path rules. We use two priorities, one for offloaded rules (fast path), and one for the control rules (slow path). To allow for that, we enable two priorities for the FDB namespace in the FS core code. Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-14net/mlx5e: Offload TC flow counters only when supportedOr Gerlitz1-1/+1
Currenly, the code that programs the flow actions into the firmware doesn't check if was actually asked to offload the statistics, fix that. Fixes: aad7e08d39bd ('net/mlx5e: Hardware offloaded flower filter statistics support') Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-14net/mlx5: Introduce bulk reading of flow countersAmir Vadai3-22/+140
This commit utilize the ability of ConnectX-4 to bulk read flow counters. Few bulk counter queries could be done instead of issuing thousands of firmware commands per second to get statistics of all flows set to HW, such as those programmed when we offload tc filters. Counters are stored sorted by hardware id, and queried in blocks (id + number of counters). Due to hardware requirement, start of block and number of counters in a block must be four aligned. Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Amir Vadai <amir@vadai.me> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-14net/mlx5: Store counters in rbtree instead of listAmir Vadai2-10/+55
In order to use bulk counters, we need to have counters sorted by id. Signed-off-by: Amir Vadai <amir@vadai.me> Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-13net: nps_enet: code reuseElad Kanfi1-10/+11
Add inline function that checks if there is a pending tx packet. Signed-off-by: Elad Kanfi <eladkan@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-13net: nps_enet: fix coding style issuesElad Kanfi1-3/+3
Fix following coding style problems : ERROR: else should follow close brace '}' + } + else { /* !dst_is_aligned */ WARNING: Missing a blank line after declarations + u32 buf = nps_enet_reg_get(priv, NPS_ENET_REG_RX_BUF); + put_unaligned_be32(buf, reg); WARNING: Missing a blank line after declarations + u32 buf; + ioread32_rep(priv->regs_base + NPS_ENET_REG_RX_BUF, &buf, 1); CHECK: Blank lines aren't necessary before a close brace '}' + + } total: 1 errors, 2 warnings, 1 checks, 683 lines checked Signed-off-by: Elad Kanfi <eladkan@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-13net: ethernet: bgmac: Remove redundant dev_err call in bgmac_probe()Wei Yongjun1-6/+2
There is a error message within devm_ioremap_resource already, so remove the dev_err call to avoid redundant error message. Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-13stmmac: dwmac-socfpga: remove redundant dev_err call in ↵Wei Yongjun1-14/+3
socfpga_dwmac_parse_data() There is a error message within devm_ioremap_resource already, so remove the dev_err call to avoid redundant error message. Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-13Merge branch 'for-upstream' of ↵David S. Miller3-5/+11
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next Johan Hedberg says: ==================== pull request: bluetooth-next 2016-07-13 Here's our main bluetooth-next pull request for the 4.8 kernel: - Fixes and cleanups in 802.15.4 and 6LoWPAN code - Fix out of bounds issue in btmrvl driver - Fixes to Bluetooth socket recvmsg return values - Use crypto_cipher_encrypt_one() instead of crypto_skcipher - Cleanup of Bluetooth connection sysfs interface - New Authentication failure reson code for Disconnected mgmt event - New USB IDs for Atheros, Qualcomm and Intel Bluetooth controllers Please let me know if there are any issues pulling. Thanks. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
Powered by cgit, Gruvboxed by Blaster4385.