aboutsummaryrefslogtreecommitdiff
path: root/drivers/net
AgeCommit message (Collapse)AuthorFilesLines
2016-12-17mlxsw: spectrum: Mark split ports as suchIdo Schimmel1-1/+1
When a port is split we should mark it as such, as otherwise the split ports aren't renamed correctly (e.g. sw1p3 -> sw1p3s1) and the unsplit operation fails: $ devlink port split sw1p3 count 4 $ devlink port unsplit eth0 devlink answers: Invalid argument [ 598.565307] mlxsw_spectrum 0000:03:00.0 eth0: Port wasn't split Fixes: 67963a33b4fd ("mlxsw: Make devlink port instances independent of spectrum/switchx2 port instances") Signed-off-by: Ido Schimmel <[email protected]> Reported-by: Tamir Winetroub <[email protected]> Reviewed-by: Elad Raz <[email protected]> Tested-by: Tamir Winetroub <[email protected]> Signed-off-by: Jiri Pirko <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2016-12-17qed: fix old-style function definitionArnd Bergmann1-1/+1
The newly added file causes a harmless warning, with "make W=1": drivers/net/ethernet/qlogic/qed/qed_iscsi.c: In function 'qed_get_iscsi_ops': drivers/net/ethernet/qlogic/qed/qed_iscsi.c:1268:29: warning: old-style function definition [-Wold-style-definition] This makes it a proper prototype. Fixes: fc831825f99e ("qed: Add support for hardware offloaded iSCSI.") Signed-off-by: Arnd Bergmann <[email protected]> Reviewed-by: Johannes Thumshirn <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2016-12-17r6040: move spinlock in r6040_close as SOFTIRQ-unsafe lock order detectedManuel Bessler1-5/+5
'ifconfig eth0 down' makes r6040_close() trigger: INFO: HARDIRQ-safe -> HARDIRQ-unsafe lock order detected Fixed by moving calls to phy_stop(), napi_disable(), netif_stop_queue() to outside of the module's private spin_lock_irq block. Found on a Versalogic Tomcat SBC with a Vortex86 SoC s1660e_5150:~# sudo ifconfig eth0 down [ 61.306415] ====================================================== [ 61.306415] [ INFO: SOFTIRQ-safe -> SOFTIRQ-unsafe lock order detected ] [ 61.306415] 4.9.0-gb898d2d-manuel #1 Not tainted [ 61.306415] ------------------------------------------------------ [ 61.306415] ifconfig/449 [HC0[0]:SC0[0]:HE0:SE1] is trying to acquire: [ 61.306415] (&dev->lock){+.+...}, at: [<c1336276>] phy_stop+0x16/0x80 [ 61.306415] and this task is already holding: [ 61.306415] (&(&lp->lock)->rlock){+.-...}, at: [<d0934c84>] r6040_close+0x24/0x230 [r6040] which would create a new lock dependency: [ 61.306415] (&(&lp->lock)->rlock){+.-...} -> (&dev->lock){+.+...} [ 61.306415] but this new dependency connects a SOFTIRQ-irq-safe lock: [ 61.306415] (&(&lp->lock)->rlock){+.-...} [ 61.306415] ... which became SOFTIRQ-irq-safe at: [ 61.306415] [ 61.306415] [<c1075bc5>] __lock_acquire+0x555/0x1770 [ 61.306415] [ 61.306415] [<c107717c>] lock_acquire+0x7c/0x150 [ 61.306415] [ 61.306415] [<c14bb334>] _raw_spin_lock_irqsave+0x24/0x40 [ 61.306415] [ 61.306415] [<d0934ac0>] r6040_start_xmit+0x30/0x1d0 [r6040] [ 61.306415] [ 61.306415] [<c13a7d4d>] dev_hard_start_xmit+0x9d/0x2d0 [ 61.306415] [ 61.306415] [<c13c8a38>] sch_direct_xmit+0xa8/0x140 [ 61.306415] [ 61.306415] [<c13a8436>] __dev_queue_xmit+0x416/0x780 [ 61.306415] [ 61.306415] [<c13a87aa>] dev_queue_xmit+0xa/0x10 [ 61.306415] [ 61.306415] [<c13b4837>] neigh_resolve_output+0x147/0x220 [ 61.306415] [ 61.306415] [<c144541b>] ip6_finish_output2+0x2fb/0x910 [ 61.306415] [ 61.306415] [<c14494e6>] ip6_finish_output+0xa6/0x1a0 [ 61.306415] [ 61.306415] [<c1449635>] ip6_output+0x55/0x320 [ 61.306415] [ 61.306415] [<c146f4d2>] mld_sendpack+0x352/0x560 [ 61.306415] [ 61.306415] [<c146fe55>] mld_ifc_timer_expire+0x155/0x280 [ 61.306415] [ 61.306415] [<c108b081>] call_timer_fn+0x81/0x270 [ 61.306415] [ 61.306415] [<c108b331>] expire_timers+0xc1/0x180 [ 61.306415] [ 61.306415] [<c108b4f7>] run_timer_softirq+0x77/0x150 [ 61.306415] [ 61.306415] [<c1043d04>] __do_softirq+0xb4/0x3d0 [ 61.306415] [ 61.306415] [<c101a15c>] do_softirq_own_stack+0x1c/0x30 [ 61.306415] [ 61.306415] [<c104416e>] irq_exit+0x8e/0xa0 [ 61.306415] [ 61.306415] [<c1019d31>] do_IRQ+0x51/0x100 [ 61.306415] [ 61.306415] [<c14bc176>] common_interrupt+0x36/0x40 [ 61.306415] [ 61.306415] [<c1134928>] set_root+0x68/0xf0 [ 61.306415] [ 61.306415] [<c1136120>] path_init+0x400/0x640 [ 61.306415] [ 61.306415] [<c11386bf>] path_lookupat+0xf/0xe0 [ 61.306415] [ 61.306415] [<c1139ebc>] filename_lookup+0x6c/0x100 [ 61.306415] [ 61.306415] [<c1139fd5>] user_path_at_empty+0x25/0x30 [ 61.306415] [ 61.306415] [<c11298c6>] SyS_faccessat+0x86/0x1e0 [ 61.306415] [ 61.306415] [<c1129a30>] SyS_access+0x10/0x20 [ 61.306415] [ 61.306415] [<c100179f>] do_int80_syscall_32+0x3f/0x110 [ 61.306415] [ 61.306415] [<c14bba3f>] restore_all+0x0/0x61 [ 61.306415] [ 61.306415] to a SOFTIRQ-irq-unsafe lock: [ 61.306415] (&dev->lock){+.+...} [ 61.306415] ... which became SOFTIRQ-irq-unsafe at: [ 61.306415] ...[ 61.306415] [ 61.306415] [<c1075c0c>] __lock_acquire+0x59c/0x1770 [ 61.306415] [ 61.306415] [<c107717c>] lock_acquire+0x7c/0x150 [ 61.306415] [ 61.306415] [<c14b7add>] mutex_lock_nested+0x2d/0x4a0 [ 61.306415] [ 61.306415] [<c133747d>] phy_probe+0x4d/0xc0 [ 61.306415] [ 61.306415] [<c1338afe>] phy_attach_direct+0xbe/0x190 [ 61.306415] [ 61.306415] [<c1338ca7>] phy_connect_direct+0x17/0x60 [ 61.306415] [ 61.306415] [<c1338d23>] phy_connect+0x33/0x70 [ 61.306415] [ 61.306415] [<d09357a0>] r6040_init_one+0x3a0/0x500 [r6040] [ 61.306415] [ 61.306415] [<c12a78c7>] pci_device_probe+0x77/0xd0 [ 61.306415] [ 61.306415] [<c12f5e15>] driver_probe_device+0x145/0x280 [ 61.306415] [ 61.306415] [<c12f5fd9>] __driver_attach+0x89/0x90 [ 61.306415] [ 61.306415] [<c12f43ef>] bus_for_each_dev+0x4f/0x80 [ 61.306415] [ 61.306415] [<c12f5954>] driver_attach+0x14/0x20 [ 61.306415] [ 61.306415] [<c12f55b7>] bus_add_driver+0x197/0x210 [ 61.306415] [ 61.306415] [<c12f6a21>] driver_register+0x51/0xd0 [ 61.306415] [ 61.306415] [<c12a6955>] __pci_register_driver+0x45/0x50 [ 61.306415] [ 61.306415] [<d0938017>] 0xd0938017 [ 61.306415] [ 61.306415] [<c100043f>] do_one_initcall+0x2f/0x140 [ 61.306415] [ 61.306415] [<c10e48c0>] do_init_module+0x4a/0x19b [ 61.306415] [ 61.306415] [<c10a680e>] load_module+0x1b2e/0x2070 [ 61.306415] [ 61.306415] [<c10a6eb9>] SyS_finit_module+0x69/0x80 [ 61.306415] [ 61.306415] [<c100179f>] do_int80_syscall_32+0x3f/0x110 [ 61.306415] [ 61.306415] [<c14bba3f>] restore_all+0x0/0x61 [ 61.306415] [ 61.306415] other info that might help us debug this: [ 61.306415] [ 61.306415] Possible interrupt unsafe locking scenario: [ 61.306415] [ 61.306415] CPU0 CPU1 [ 61.306415] ---- ---- [ 61.306415] lock(&dev->lock); [ 61.306415] local_irq_disable(); [ 61.306415] lock(&(&lp->lock)->rlock); [ 61.306415] lock(&dev->lock); [ 61.306415] <Interrupt> [ 61.306415] lock(&(&lp->lock)->rlock); [ 61.306415] [ 61.306415] *** DEADLOCK *** [ 61.306415] [ 61.306415] 2 locks held by ifconfig/449: [ 61.306415] #0: (rtnl_mutex){+.+.+.}, at: [<c13b68ef>] rtnl_lock+0xf/0x20 [ 61.306415] #1: (&(&lp->lock)->rlock){+.-...}, at: [<d0934c84>] r6040_close+0x24/0x230 [r6040] [ 61.306415] [ 61.306415] the dependencies between SOFTIRQ-irq-safe lock and the holding lock: [ 61.306415] -> (&(&lp->lock)->rlock){+.-...} ops: 3049 { [ 61.306415] HARDIRQ-ON-W at: [ 61.306415] [ 61.306415] [<c1075be7>] __lock_acquire+0x577/0x1770 [ 61.306415] [ 61.306415] [<c107717c>] lock_acquire+0x7c/0x150 [ 61.306415] [ 61.306415] [<c14bb21b>] _raw_spin_lock+0x1b/0x30 [ 61.306415] [ 61.306415] [<d09343cc>] r6040_poll+0x2c/0x330 [r6040] [ 61.306415] [ 61.306415] [<c13a5577>] net_rx_action+0x197/0x340 [ 61.306415] [ 61.306415] [<c1043d04>] __do_softirq+0xb4/0x3d0 [ 61.306415] [ 61.306415] [<c1044037>] run_ksoftirqd+0x17/0x40 [ 61.306415] [ 61.306415] [<c105fe91>] smpboot_thread_fn+0x141/0x180 [ 61.306415] [ 61.306415] [<c105c84e>] kthread+0xde/0x110 [ 61.306415] [ 61.306415] [<c14bb949>] ret_from_fork+0x19/0x30 [ 61.306415] IN-SOFTIRQ-W at: [ 61.306415] [ 61.306415] [<c1075bc5>] __lock_acquire+0x555/0x1770 [ 61.306415] [ 61.306415] [<c107717c>] lock_acquire+0x7c/0x150 [ 61.306415] [ 61.306415] [<c14bb334>] _raw_spin_lock_irqsave+0x24/0x40 [ 61.306415] [ 61.306415] [<d0934ac0>] r6040_start_xmit+0x30/0x1d0 [r6040] [ 61.306415] [ 61.306415] [<c13a7d4d>] dev_hard_start_xmit+0x9d/0x2d0 [ 61.306415] [ 61.306415] [<c13c8a38>] sch_direct_xmit+0xa8/0x140 [ 61.306415] [ 61.306415] [<c13a8436>] __dev_queue_xmit+0x416/0x780 [ 61.306415] [ 61.306415] [<c13a87aa>] dev_queue_xmit+0xa/0x10 [ 61.306415] [ 61.306415] [<c13b4837>] neigh_resolve_output+0x147/0x220 [ 61.306415] [ 61.306415] [<c144541b>] ip6_finish_output2+0x2fb/0x910 [ 61.306415] [ 61.306415] [<c14494e6>] ip6_finish_output+0xa6/0x1a0 [ 61.306415] [ 61.306415] [<c1449635>] ip6_output+0x55/0x320 [ 61.306415] [ 61.306415] [<c146f4d2>] mld_sendpack+0x352/0x560 [ 61.306415] [ 61.306415] [<c146fe55>] mld_ifc_timer_expire+0x155/0x280 [ 61.306415] [ 61.306415] [<c108b081>] call_timer_fn+0x81/0x270 [ 61.306415] [ 61.306415] [<c108b331>] expire_timers+0xc1/0x180 [ 61.306415] [ 61.306415] [<c108b4f7>] run_timer_softirq+0x77/0x150 [ 61.306415] [ 61.306415] [<c1043d04>] __do_softirq+0xb4/0x3d0 [ 61.306415] [ 61.306415] [<c101a15c>] do_softirq_own_stack+0x1c/0x30 [ 61.306415] [ 61.306415] [<c104416e>] irq_exit+0x8e/0xa0 [ 61.306415] [ 61.306415] [<c1019d31>] do_IRQ+0x51/0x100 [ 61.306415] [ 61.306415] [<c14bc176>] common_interrupt+0x36/0x40 [ 61.306415] [ 61.306415] [<c1134928>] set_root+0x68/0xf0 [ 61.306415] [ 61.306415] [<c1136120>] path_init+0x400/0x640 [ 61.306415] [ 61.306415] [<c11386bf>] path_lookupat+0xf/0xe0 [ 61.306415] [ 61.306415] [<c1139ebc>] filename_lookup+0x6c/0x100 [ 61.306415] [ 61.306415] [<c1139fd5>] user_path_at_empty+0x25/0x30 [ 61.306415] [ 61.306415] [<c11298c6>] SyS_faccessat+0x86/0x1e0 [ 61.306415] [ 61.306415] [<c1129a30>] SyS_access+0x10/0x20 [ 61.306415] [ 61.306415] [<c100179f>] do_int80_syscall_32+0x3f/0x110 [ 61.306415] [ 61.306415] [<c14bba3f>] restore_all+0x0/0x61 [ 61.306415] INITIAL USE at: [ 61.306415] [ 61.306415] [<c107586e>] __lock_acquire+0x1fe/0x1770 [ 61.306415] [ 61.306415] [<c107717c>] lock_acquire+0x7c/0x150 [ 61.306415] [ 61.306415] [<c14bb334>] _raw_spin_lock_irqsave+0x24/0x40 [ 61.306415] [ 61.306415] [<d093474e>] r6040_get_stats+0x1e/0x60 [r6040] [ 61.306415] [ 61.306415] [<c139fb16>] dev_get_stats+0x96/0xc0 [ 61.306415] [ 61.306415] [<c14b416e>] rtnl_fill_stats+0x36/0xfd [ 61.306415] [ 61.306415] [<c13b7b3c>] rtnl_fill_ifinfo+0x47c/0xce0 [ 61.306415] [ 61.306415] [<c13bc08e>] rtmsg_ifinfo_build_skb+0x4e/0xd0 [ 61.306415] [ 61.306415] [<c13bc120>] rtmsg_ifinfo.part.20+0x10/0x40 [ 61.306415] [ 61.306415] [<c13bc16b>] rtmsg_ifinfo+0x1b/0x20 [ 61.306415] [ 61.306415] [<c13a9d19>] register_netdevice+0x409/0x550 [ 61.306415] [ 61.306415] [<c13a9e72>] register_netdev+0x12/0x20 [ 61.306415] [ 61.306415] [<d09357e8>] r6040_init_one+0x3e8/0x500 [r6040] [ 61.306415] [ 61.306415] [<c12a78c7>] pci_device_probe+0x77/0xd0 [ 61.306415] [ 61.306415] [<c12f5e15>] driver_probe_device+0x145/0x280 [ 61.306415] [ 61.306415] [<c12f5fd9>] __driver_attach+0x89/0x90 [ 61.306415] [ 61.306415] [<c12f43ef>] bus_for_each_dev+0x4f/0x80 [ 61.306415] [ 61.306415] [<c12f5954>] driver_attach+0x14/0x20 [ 61.306415] [ 61.306415] [<c12f55b7>] bus_add_driver+0x197/0x210 [ 61.306415] [ 61.306415] [<c12f6a21>] driver_register+0x51/0xd0 [ 61.306415] [ 61.306415] [<c12a6955>] __pci_register_driver+0x45/0x50 [ 61.306415] [ 61.306415] [<d0938017>] 0xd0938017 [ 61.306415] [ 61.306415] [<c100043f>] do_one_initcall+0x2f/0x140 [ 61.306415] [ 61.306415] [<c10e48c0>] do_init_module+0x4a/0x19b [ 61.306415] [ 61.306415] [<c10a680e>] load_module+0x1b2e/0x2070 [ 61.306415] [ 61.306415] [<c10a6eb9>] SyS_finit_module+0x69/0x80 [ 61.306415] [ 61.306415] [<c100179f>] do_int80_syscall_32+0x3f/0x110 [ 61.306415] [ 61.306415] [<c14bba3f>] restore_all+0x0/0x61 [ 61.306415] } [ 61.306415] ... key at: [<d0936280>] __key.45893+0x0/0xfffff739 [r6040] [ 61.306415] ... acquired at: [ 61.306415] [ 61.306415] [<c1074a32>] check_irq_usage+0x42/0xb0 [ 61.306415] [ 61.306415] [<c107677c>] __lock_acquire+0x110c/0x1770 [ 61.306415] [ 61.306415] [<c107717c>] lock_acquire+0x7c/0x150 [ 61.306415] [ 61.306415] [<c14b7add>] mutex_lock_nested+0x2d/0x4a0 [ 61.306415] [ 61.306415] [<c1336276>] phy_stop+0x16/0x80 [ 61.306415] [ 61.306415] [<d0934ce9>] r6040_close+0x89/0x230 [r6040] [ 61.306415] [ 61.306415] [<c13a0a91>] __dev_close_many+0x61/0xa0 [ 61.306415] [ 61.306415] [<c13a0bbf>] __dev_close+0x1f/0x30 [ 61.306415] [ 61.306415] [<c13a9127>] __dev_change_flags+0x87/0x150 [ 61.306415] [ 61.306415] [<c13a9213>] dev_change_flags+0x23/0x60 [ 61.306415] [ 61.306415] [<c1416238>] devinet_ioctl+0x5f8/0x6f0 [ 61.306415] [ 61.306415] [<c1417f75>] inet_ioctl+0x65/0x90 [ 61.306415] [ 61.306415] [<c1389b54>] sock_ioctl+0x124/0x2b0 [ 61.306415] [ 61.306415] [<c113cf7c>] do_vfs_ioctl+0x7c/0x790 [ 61.306415] [ 61.306415] [<c113d6b8>] SyS_ioctl+0x28/0x50 [ 61.306415] [ 61.306415] [<c100179f>] do_int80_syscall_32+0x3f/0x110 [ 61.306415] [ 61.306415] [<c14bba3f>] restore_all+0x0/0x61 [ 61.306415] [ 61.306415] the dependencies between the lock to be acquired[ 61.306415] and SOFTIRQ-irq-unsafe lock: [ 61.306415] -> (&dev->lock){+.+...} ops: 56 { [ 61.306415] HARDIRQ-ON-W at: [ 61.306415] [ 61.306415] [<c1075be7>] __lock_acquire+0x577/0x1770 [ 61.306415] [ 61.306415] [<c107717c>] lock_acquire+0x7c/0x150 [ 61.306415] [ 61.306415] [<c14b7add>] mutex_lock_nested+0x2d/0x4a0 [ 61.306415] [ 61.306415] [<c133747d>] phy_probe+0x4d/0xc0 [ 61.306415] [ 61.306415] [<c1338afe>] phy_attach_direct+0xbe/0x190 [ 61.306415] [ 61.306415] [<c1338ca7>] phy_connect_direct+0x17/0x60 [ 61.306415] [ 61.306415] [<c1338d23>] phy_connect+0x33/0x70 [ 61.306415] [ 61.306415] [<d09357a0>] r6040_init_one+0x3a0/0x500 [r6040] [ 61.306415] [ 61.306415] [<c12a78c7>] pci_device_probe+0x77/0xd0 [ 61.306415] [ 61.306415] [<c12f5e15>] driver_probe_device+0x145/0x280 [ 61.306415] [ 61.306415] [<c12f5fd9>] __driver_attach+0x89/0x90 [ 61.306415] [ 61.306415] [<c12f43ef>] bus_for_each_dev+0x4f/0x80 [ 61.306415] [ 61.306415] [<c12f5954>] driver_attach+0x14/0x20 [ 61.306415] [ 61.306415] [<c12f55b7>] bus_add_driver+0x197/0x210 [ 61.306415] [ 61.306415] [<c12f6a21>] driver_register+0x51/0xd0 [ 61.306415] [ 61.306415] [<c12a6955>] __pci_register_driver+0x45/0x50 [ 61.306415] [ 61.306415] [<d0938017>] 0xd0938017 [ 61.306415] [ 61.306415] [<c100043f>] do_one_initcall+0x2f/0x140 [ 61.306415] [ 61.306415] [<c10e48c0>] do_init_module+0x4a/0x19b [ 61.306415] [ 61.306415] [<c10a680e>] load_module+0x1b2e/0x2070 [ 61.306415] [ 61.306415] [<c10a6eb9>] SyS_finit_module+0x69/0x80 [ 61.306415] [ 61.306415] [<c100179f>] do_int80_syscall_32+0x3f/0x110 [ 61.306415] [ 61.306415] [<c14bba3f>] restore_all+0x0/0x61 [ 61.306415] SOFTIRQ-ON-W at: [ 61.306415] [ 61.306415] [<c1075c0c>] __lock_acquire+0x59c/0x1770 [ 61.306415] [ 61.306415] [<c107717c>] lock_acquire+0x7c/0x150 [ 61.306415] [ 61.306415] [<c14b7add>] mutex_lock_nested+0x2d/0x4a0 [ 61.306415] [ 61.306415] [<c133747d>] phy_probe+0x4d/0xc0 [ 61.306415] [ 61.306415] [<c1338afe>] phy_attach_direct+0xbe/0x190 [ 61.306415] [ 61.306415] [<c1338ca7>] phy_connect_direct+0x17/0x60 [ 61.306415] [ 61.306415] [<c1338d23>] phy_connect+0x33/0x70 [ 61.306415] [ 61.306415] [<d09357a0>] r6040_init_one+0x3a0/0x500 [r6040] [ 61.306415] [ 61.306415] [<c12a78c7>] pci_device_probe+0x77/0xd0 [ 61.306415] [ 61.306415] [<c12f5e15>] driver_probe_device+0x145/0x280 [ 61.306415] [ 61.306415] [<c12f5fd9>] __driver_attach+0x89/0x90 [ 61.306415] [ 61.306415] [<c12f43ef>] bus_for_each_dev+0x4f/0x80 [ 61.306415] [ 61.306415] [<c12f5954>] driver_attach+0x14/0x20 [ 61.306415] [ 61.306415] [<c12f55b7>] bus_add_driver+0x197/0x210 [ 61.306415] [ 61.306415] [<c12f6a21>] driver_register+0x51/0xd0 [ 61.306415] [ 61.306415] [<c12a6955>] __pci_register_driver+0x45/0x50 [ 61.306415] [ 61.306415] [<d0938017>] 0xd0938017 [ 61.306415] [ 61.306415] [<c100043f>] do_one_initcall+0x2f/0x140 [ 61.306415] [ 61.306415] [<c10e48c0>] do_init_module+0x4a/0x19b [ 61.306415] [ 61.306415] [<c10a680e>] load_module+0x1b2e/0x2070 [ 61.306415] [ 61.306415] [<c10a6eb9>] SyS_finit_module+0x69/0x80 [ 61.306415] [ 61.306415] [<c100179f>] do_int80_syscall_32+0x3f/0x110 [ 61.306415] [ 61.306415] [<c14bba3f>] restore_all+0x0/0x61 [ 61.306415] INITIAL USE at: [ 61.306415] [ 61.306415] [<c107586e>] __lock_acquire+0x1fe/0x1770 [ 61.306415] [ 61.306415] [<c107717c>] lock_acquire+0x7c/0x150 [ 61.306415] [ 61.306415] [<c14b7add>] mutex_lock_nested+0x2d/0x4a0 [ 61.306415] [ 61.306415] [<c133747d>] phy_probe+0x4d/0xc0 [ 61.306415] [ 61.306415] [<c1338afe>] phy_attach_direct+0xbe/0x190 [ 61.306415] [ 61.306415] [<c1338ca7>] phy_connect_direct+0x17/0x60 [ 61.306415] [ 61.306415] [<c1338d23>] phy_connect+0x33/0x70 [ 61.306415] [ 61.306415] [<d09357a0>] r6040_init_one+0x3a0/0x500 [r6040] [ 61.306415] [ 61.306415] [<c12a78c7>] pci_device_probe+0x77/0xd0 [ 61.306415] [ 61.306415] [<c12f5e15>] driver_probe_device+0x145/0x280 [ 61.306415] [ 61.306415] [<c12f5fd9>] __driver_attach+0x89/0x90 [ 61.306415] [ 61.306415] [<c12f43ef>] bus_for_each_dev+0x4f/0x80 [ 61.306415] [ 61.306415] [<c12f5954>] driver_attach+0x14/0x20 [ 61.306415] [ 61.306415] [<c12f55b7>] bus_add_driver+0x197/0x210 [ 61.306415] [ 61.306415] [<c12f6a21>] driver_register+0x51/0xd0 [ 61.306415] [ 61.306415] [<c12a6955>] __pci_register_driver+0x45/0x50 [ 61.306415] [ 61.306415] [<d0938017>] 0xd0938017 [ 61.306415] [ 61.306415] [<c100043f>] do_one_initcall+0x2f/0x140 [ 61.306415] [ 61.306415] [<c10e48c0>] do_init_module+0x4a/0x19b [ 61.306415] [ 61.306415] [<c10a680e>] load_module+0x1b2e/0x2070 [ 61.306415] [ 61.306415] [<c10a6eb9>] SyS_finit_module+0x69/0x80 [ 61.306415] [ 61.306415] [<c100179f>] do_int80_syscall_32+0x3f/0x110 [ 61.306415] [ 61.306415] [<c14bba3f>] restore_all+0x0/0x61 [ 61.306415] } [ 61.306415] ... key at: [<c1f28f39>] __key.43998+0x0/0x8 [ 61.306415] ... acquired at: [ 61.306415] [ 61.306415] [<c1074a32>] check_irq_usage+0x42/0xb0 [ 61.306415] [ 61.306415] [<c107677c>] __lock_acquire+0x110c/0x1770 [ 61.306415] [ 61.306415] [<c107717c>] lock_acquire+0x7c/0x150 [ 61.306415] [ 61.306415] [<c14b7add>] mutex_lock_nested+0x2d/0x4a0 [ 61.306415] [ 61.306415] [<c1336276>] phy_stop+0x16/0x80 [ 61.306415] [ 61.306415] [<d0934ce9>] r6040_close+0x89/0x230 [r6040] [ 61.306415] [ 61.306415] [<c13a0a91>] __dev_close_many+0x61/0xa0 [ 61.306415] [ 61.306415] [<c13a0bbf>] __dev_close+0x1f/0x30 [ 61.306415] [ 61.306415] [<c13a9127>] __dev_change_flags+0x87/0x150 [ 61.306415] [ 61.306415] [<c13a9213>] dev_change_flags+0x23/0x60 [ 61.306415] [ 61.306415] [<c1416238>] devinet_ioctl+0x5f8/0x6f0 [ 61.306415] [ 61.306415] [<c1417f75>] inet_ioctl+0x65/0x90 [ 61.306415] [ 61.306415] [<c1389b54>] sock_ioctl+0x124/0x2b0 [ 61.306415] [ 61.306415] [<c113cf7c>] do_vfs_ioctl+0x7c/0x790 [ 61.306415] [ 61.306415] [<c113d6b8>] SyS_ioctl+0x28/0x50 [ 61.306415] [ 61.306415] [<c100179f>] do_int80_syscall_32+0x3f/0x110 [ 61.306415] [ 61.306415] [<c14bba3f>] restore_all+0x0/0x61 [ 61.306415] [ 61.306415] [ 61.306415] stack backtrace: [ 61.306415] CPU: 0 PID: 449 Comm: ifconfig Not tainted 4.9.0-gb898d2d-manuel #1 [ 61.306415] Call Trace: [ 61.306415] dump_stack+0x16/0x19 [ 61.306415] check_usage+0x3f6/0x550 [ 61.306415] ? check_usage+0x4d/0x550 [ 61.306415] check_irq_usage+0x42/0xb0 [ 61.306415] __lock_acquire+0x110c/0x1770 [ 61.306415] lock_acquire+0x7c/0x150 [ 61.306415] ? phy_stop+0x16/0x80 [ 61.306415] mutex_lock_nested+0x2d/0x4a0 [ 61.306415] ? phy_stop+0x16/0x80 [ 61.306415] ? r6040_close+0x24/0x230 [r6040] [ 61.306415] ? __delay+0x9/0x10 [ 61.306415] phy_stop+0x16/0x80 [ 61.306415] r6040_close+0x89/0x230 [r6040] [ 61.306415] __dev_close_many+0x61/0xa0 [ 61.306415] __dev_close+0x1f/0x30 [ 61.306415] __dev_change_flags+0x87/0x150 [ 61.306415] dev_change_flags+0x23/0x60 [ 61.306415] devinet_ioctl+0x5f8/0x6f0 [ 61.306415] inet_ioctl+0x65/0x90 [ 61.306415] sock_ioctl+0x124/0x2b0 [ 61.306415] ? dlci_ioctl_set+0x30/0x30 [ 61.306415] do_vfs_ioctl+0x7c/0x790 [ 61.306415] ? trace_hardirqs_on+0xb/0x10 [ 61.306415] ? call_rcu_sched+0xd/0x10 [ 61.306415] ? __put_cred+0x32/0x50 [ 61.306415] ? SyS_faccessat+0x178/0x1e0 [ 61.306415] SyS_ioctl+0x28/0x50 [ 61.306415] do_int80_syscall_32+0x3f/0x110 [ 61.306415] entry_INT80_32+0x2f/0x2f [ 61.306415] EIP: 0xb764d364 [ 61.306415] EFLAGS: 00000286 CPU: 0 [ 61.306415] EAX: ffffffda EBX: 00000004 ECX: 00008914 EDX: bfa99d7c [ 61.306415] ESI: bfa99e4c EDI: fffffffe EBP: 00000004 ESP: bfa99d58 [ 61.306415] DS: 007b ES: 007b FS: 0000 GS: 0033 SS: 007b [ 63.836607] r6040 0000:00:08.0 eth0: Link is Down Signed-off-by: Manuel Bessler <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2016-12-17irda: w83977af_ir: cleanup an indent issueDan Carpenter1-3/+3
In commit 99d8d2159d7c ("irda: w83977af_ir: Neaten logging"), we accidentally added an extra tab to these lines. Signed-off-by: Dan Carpenter <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2016-12-17net: sfc: use new api ethtool_{get|set}_link_ksettingsPhilippe Reynes3-42/+65
The ethtool api {get|set}_settings is deprecated. We move this driver to new api {get|set}_link_ksettings. Signed-off-by: Philippe Reynes <[email protected]> Tested-by: Bert Kenward <[email protected]> Acked-by: Bert Kenward <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2016-12-17net: davicom: dm9000: use new api ethtool_{get|set}_link_ksettingsPhilippe Reynes1-6/+8
The ethtool api {get|set}_settings is deprecated. We move this driver to new api {get|set}_link_ksettings. Signed-off-by: Philippe Reynes <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2016-12-17net: cirrus: ep93xx: use new api ethtool_{get|set}_link_ksettingsPhilippe Reynes1-6/+8
The ethtool api {get|set}_settings is deprecated. We move this driver to new api {get|set}_link_ksettings. Signed-off-by: Philippe Reynes <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2016-12-17net: chelsio: cxgb3: use new api ethtool_{get|set}_link_ksettingsPhilippe Reynes1-28/+37
The ethtool api {get|set}_settings is deprecated. We move this driver to new api {get|set}_link_ksettings. Signed-off-by: Philippe Reynes <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2016-12-17net: chelsio: cxgb2: use new api ethtool_{get|set}_link_ksettingsPhilippe Reynes1-27/+37
The ethtool api {get|set}_settings is deprecated. We move this driver to new api {get|set}_link_ksettings. Signed-off-by: Philippe Reynes <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2016-12-17gtp: Fix initialization of Flags octet in GTPv1 headerHarald Welte1-2/+2
When generating a GTPv1 header in gtp1_push_header(), initialize the 'reserved' bit to zero. All 3GPP specifications for GTPv1 from Release 99 through Release 13 agree that a transmitter shall set this bit to zero, see e.g. Note 0 of Figure 2 in Section 6 of 3GPP TS 29.060 v13.5.0 Release 13, available from http://www.etsi.org/deliver/etsi_ts/129000_129099/129060/13.05.00_60/ts_129060v130500p.pdf Signed-off-by: Harald Welte <[email protected]> Signed-off-by: Pablo Neira Ayuso <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2016-12-17gtp: gtp_check_src_ms_ipv4() always return successLionel Gauthier1-2/+2
gtp_check_src_ms_ipv4() did not find the PDP context matching with the UE IP address because the memory location is not right, but the result is inverted by the Boolean "not" operator. So whatever is the PDP context, any call to this function is successful. Signed-off-by: Lionel Gauthier <[email protected]> Signed-off-by: Pablo Neira Ayuso <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2016-12-17bna: use designated initializersKees Cook1-4/+4
Prepare to mark sensitive kernel structures for randomization by making sure they're using designated initializers. These were identified during allyesconfig builds of x86, arm, and arm64, with most initializer fixes extracted from grsecurity. Signed-off-by: Kees Cook <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2016-12-17WAN: use designated initializersKees Cook1-48/+49
Prepare to mark sensitive kernel structures for randomization by making sure they're using designated initializers. These were identified during allyesconfig builds of x86, arm, and arm64, with most initializer fixes extracted from grsecurity. Signed-off-by: Kees Cook <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2016-12-17virtio_net: xdp, add slowpath case for non contiguous buffersJohn Fastabend1-1/+74
virtio_net XDP support expects receive buffers to be contiguous. If this is not the case we enable a slowpath to allow connectivity to continue but at a significan performance overhead associated with linearizing data. To make it painfully aware to users that XDP is running in a degraded mode we throw an xdp buffer error. To linearize packets we allocate a page and copy the segments of the data, including the header, into it. After this the page can be handled by XDP code flow as normal. Then depending on the return code the page is either freed or sent to the XDP xmit path. There is no attempt to optimize this path. This case is being handled simple as a precaution in case some unknown backend were to generate packets in this form. To test this I had to hack qemu and force it to generate these packets. I do not expect this case to be generated by "real" backends. Signed-off-by: John Fastabend <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2016-12-17virtio_net: add XDP_TX supportJohn Fastabend1-7/+93
This adds support for the XDP_TX action to virtio_net. When an XDP program is run and returns the XDP_TX action the virtio_net XDP implementation will transmit the packet on a TX queue that aligns with the current CPU that the XDP packet was processed on. Before sending the packet the header is zeroed. Also XDP is expected to handle checksum correctly so no checksum offload support is provided. Signed-off-by: John Fastabend <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2016-12-17virtio_net: add dedicated XDP transmit queuesJohn Fastabend1-2/+28
XDP requires using isolated transmit queues to avoid interference with normal networking stack (BQL, NETDEV_TX_BUSY, etc). This patch adds a XDP queue per cpu when a XDP program is loaded and does not expose the queues to the OS via the normal API call to netif_set_real_num_tx_queues(). This way the stack will never push an skb to these queues. However virtio/vhost/qemu implementation only allows for creating TX/RX queue pairs at this time so creating only TX queues was not possible. And because the associated RX queues are being created I went ahead and exposed these to the stack and let the backend use them. This creates more RX queues visible to the network stack than TX queues which is worth mentioning but does not cause any issues as far as I can tell. Signed-off-by: John Fastabend <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2016-12-17virtio_net: Add XDP supportJohn Fastabend1-5/+171
This adds XDP support to virtio_net. Some requirements must be met for XDP to be enabled depending on the mode. First it will only be supported with LRO disabled so that data is not pushed across multiple buffers. Second the MTU must be less than a page size to avoid having to handle XDP across multiple pages. If mergeable receive is enabled this patch only supports the case where header and data are in the same buf which we can check when a packet is received by looking at num_buf. If the num_buf is greater than 1 and a XDP program is loaded the packet is dropped and a warning is thrown. When any_header_sg is set this does not happen and both header and data is put in a single buffer as expected so we check this when XDP programs are loaded. Subsequent patches will process the packet in a degraded mode to ensure connectivity and correctness is not lost even if backend pushes packets into multiple buffers. If big packets mode is enabled and MTU/LRO conditions above are met then XDP is allowed. This patch was tested with qemu with vhost=on and vhost=off where mergeable and big_packet modes were forced via hard coding feature negotiation. Multiple buffers per packet was forced via a small test patch to vhost.c in the vhost=on qemu mode. Suggested-by: Shrijeet Mukherjee <[email protected]> Signed-off-by: John Fastabend <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2016-12-17dpaa_eth: remove redundant dependency on FSL_SOCMadalin Bucur1-1/+1
Signed-off-by: Madalin Bucur <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2016-12-17dpaa_eth: use big endian accessorsClaudiu Manoil1-34/+37
Ensure correct access to the big endian QMan HW through proper accessors. Signed-off-by: Claudiu Manoil <[email protected]> Signed-off-by: Madalin Bucur <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2016-12-17net: vrf: Drop conntrack data after pass through VRF device on TxDavid Ahern1-0/+4
Locally originated traffic in a VRF fails in the presence of a POSTROUTING rule. For example, $ iptables -t nat -A POSTROUTING -s 11.1.1.0/24 -j MASQUERADE $ ping -I red -c1 11.1.1.3 ping: Warning: source address might be selected on device other than red. PING 11.1.1.3 (11.1.1.3) from 11.1.1.2 red: 56(84) bytes of data. ping: sendmsg: Operation not permitted Worse, the above causes random corruption resulting in a panic in random places (I have not seen a consistent backtrace). Call nf_reset to drop the conntrack info following the pass through the VRF device. The nf_reset is needed on Tx but not Rx because of the order in which NF_HOOK's are hit: on Rx the VRF device is after the real ingress device and on Tx it is is before the real egress device. Connection tracking should be tied to the real egress device and not the VRF device. Fixes: 8f58336d3f78a ("net: Add ethernet header for pass through VRF device") Fixes: 35402e3136634 ("net: Add IPv6 support to VRF device") Signed-off-by: David Ahern <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2016-12-17net: vrf: Fix NAT within a VRFDavid Ahern1-2/+0
Connection tracking with VRF is broken because the pass through the VRF device drops the connection tracking info. Removing the call to nf_reset allows DNAT and MASQUERADE to work across interfaces within a VRF. Fixes: 73e20b761acf ("net: vrf: Add support for PREROUTING rules on vrf device") Signed-off-by: David Ahern <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2016-12-17net: macb: Added PCI wrapper for Platform Driver.Bartosz Folta4-5/+189
There are hardware PCI implementations of Cadence GEM network controller. This patch will allow to use such hardware with reuse of existing Platform Driver. Signed-off-by: Bartosz Folta <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2016-12-17ibmveth: calculate gso_segs for large packetsThomas Falcon1-2/+10
Include calculations to compute the number of segments that comprise an aggregated large packet. Signed-off-by: Thomas Falcon <[email protected]> Reviewed-by: Marcelo Ricardo Leitner <[email protected]> Reviewed-by: Jonathan Maxwell <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2016-12-17net: qcom/emac: don't try to claim clocks on ACPI systemsTimur Tabi1-0/+9
On ACPI systems, clocks are not available to drivers directly. They are handled exclusively by ACPI and/or firmware, so there is no clock driver. Calls to clk_get() always fail, so we should not even attempt to claim any clocks on ACPI systems. Signed-off-by: Timur Tabi <[email protected]> Reviewed-by: Florian Fainelli <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2016-12-16encx24j600: Fix some checkstyle warningsJeroen De Wachter2-8/+25
Signed-off-by: Jeroen De Wachter <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2016-12-16encx24j600: bugfix - always move ERXTAIL to next packet in encx24j600_rx_packetsJeroen De Wachter1-1/+2
Before, encx24j600_rx_packets did not update encx24j600_priv's next_packet member when an error occurred during packet handling (either because the packet's RSV header indicates an error or because the encx24j600_receive_packet method can't allocate an sk_buff). If the next_packet member is not updated, the ERXTAIL register will be set to the same value it had before, which means the bad packet remains in the component's memory and its RSV header will be read again when a new packet arrives. If the RSV header indicates a bad packet or if sk_buff allocation continues to fail, new packets will be stored in the component's memory until that memory is full, after which packets will be dropped. The SETPKTDEC command is always executed though, so the encx24j600 hardware has an incorrect count of the packets in its memory. To prevent this, the next_packet member should always be updated, allowing the packet to be skipped (either because it's bad, as indicated in its RSV header, or because allocating an sk_buff failed). In the allocation failure case, this does mean dropping a valid packet, but dropping the oldest packet to keep as much memory as possible available for new packets seems preferable to keeping old (but valid) packets around while dropping new ones. Signed-off-by: Jeroen De Wachter <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2016-12-16net: ethernet: hip04: Call SET_NETDEV_DEV()Dongpo Li1-1/+1
The hip04 driver calls into PHYLIB which now checks for net_device->dev.parent, so make sure we do set it before calling into any MDIO/PHYLIB related function. Fixes: ec988ad78ed6 ("phy: Don't increment MDIO bus refcount unless it's a different owner") Signed-off-by: Dongpo Li <[email protected]> Reviewed-by: Florian Fainelli <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2016-12-16net: ethernet: hisi_femac: Call SET_NETDEV_DEV()Dongpo Li1-1/+1
The hisi_femac driver calls into PHYLIB which now checks for net_device->dev.parent, so make sure we do set it before calling into any MDIO/PHYLIB related function. Fixes: ec988ad78ed6 ("phy: Don't increment MDIO bus refcount unless it's a different owner") Signed-off-by: Dongpo Li <[email protected]> Reviewed-by: Florian Fainelli <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2016-12-16net: dsa: mv88e6xxx: Fix opps when adding vlan bridgeAndrew Lunn1-0/+6
A port is not necessarily assigned to a netdev. And a port does not need to be a member of a bridge. So when iterating over all ports, check before using the netdev and bridge_dev for a port. Otherwise we dereference a NULL pointer. Fixes: da9c359e19f0 ("net: dsa: mv88e6xxx: check hardware VLAN in use") Signed-off-by: Andrew Lunn <[email protected]> Reviewed-by: Vivien Didelot <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2016-12-16net/3com/3c515: Fix timer handling, prevent leaks and crashesThomas Gleixner1-7/+8
The timer handling in this driver is broken in several ways: - corkscrew_open() initializes and arms a timer before requesting the device interrupt. If the request fails the timer stays armed. A second call to corkscrew_open will unconditionally reinitialize the quued timer and arm it again. Also a immediate device removal will leave the timer queued because close() is not called (open() failed) and therefore nothing issues del_timer(). The reinitialization corrupts the link chain in the timer wheel hash bucket and causes a NULL pointer dereference when the timer wheel tries to operate on that hash bucket. Immediate device removal lets the link chain poke into freed and possibly reused memory. Solution: Arm the timer after the successful irq request. - corkscrew_close() uses del_timer() On close the timer is disarmed with del_timer() which lets the following code race against a concurrent timer expiry function. Solution: Use del_timer_sync() instead - corkscrew_close() calls del_timer() unconditionally del_timer() is invoked even if the timer was never initialized. This works by chance because the struct containing the timer is zeroed at allocation time. Solution: Move the setup of the timer into corkscrew_setup(). Reported-by: Matthew Whitehead <[email protected]> Signed-off-by: Thomas Gleixner <[email protected]> Cc: Andy Lutomirski <[email protected]> Cc: [email protected] Signed-off-by: David S. Miller <[email protected]>
2016-12-16Merge branch 'for-linus' of ↵Linus Torvalds2-8/+3
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs Pull vfs updates from Al Viro: - more ->d_init() stuff (work.dcache) - pathname resolution cleanups (work.namei) - a few missing iov_iter primitives - copy_from_iter_full() and friends. Either copy the full requested amount, advance the iterator and return true, or fail, return false and do _not_ advance the iterator. Quite a few open-coded callers converted (and became more readable and harder to fuck up that way) (work.iov_iter) - several assorted patches, the big one being logfs removal * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: logfs: remove from tree vfs: fix put_compat_statfs64() does not handle errors namei: fold should_follow_link() with the step into not-followed link namei: pass both WALK_GET and WALK_MORE to should_follow_link() namei: invert WALK_PUT logics namei: shift interpretation of LOOKUP_FOLLOW inside should_follow_link() namei: saner calling conventions for mountpoint_last() namei.c: get rid of user_path_parent() switch getfrag callbacks to ..._full() primitives make skb_add_data,{_nocache}() and skb_copy_to_page_nocache() advance only on success [iov_iter] new primitives - copy_from_iter_full() and friends don't open-code file_inode() ceph: switch to use of ->d_init() ceph: unify dentry_operations instances lustre: switch to use of ->d_init()
2016-12-15Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhostLinus Torvalds31-55/+6
Pull virtio updates from Michael Tsirkin: "virtio, vhost: new device, fixes, speedups This includes the new virtio crypto device, and fixes all over the place. In particular enabling endian-ness checks for sparse builds found some bugs which this fixes. And it appears that everyone is in agreement that disabling endian-ness sparse checks shouldn't be necessary any longer. So this enables them for everyone, and drops the __CHECK_ENDIAN__ and __bitwise__ APIs. IRQ handling in virtio has been refactored somewhat, the larger switch to IRQ_SHARED will have to wait as it proved too aggressive" * tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (34 commits) Makefile: drop -D__CHECK_ENDIAN__ from cflags fs/logfs: drop __CHECK_ENDIAN__ Documentation/sparse: drop __CHECK_ENDIAN__ linux: drop __bitwise__ everywhere checkpatch: replace __bitwise__ with __bitwise Documentation/sparse: drop __bitwise__ tools: enable endian checks for all sparse builds linux/types.h: enable endian checks for all sparse builds virtio_mmio: Set dev.release() to avoid warning vhost: remove unused feature bit virtio_ring: fix description of virtqueue_get_buf vhost/scsi: Remove unused but set variable tools/virtio: use {READ,WRITE}_ONCE() in uaccess.h vringh: kill off ACCESS_ONCE() tools/virtio: fix READ_ONCE() crypto: add virtio-crypto driver vhost: cache used event for better performance vsock: lookup and setup guest_cid inside vhost_vsock_lock virtio_pci: split vp_try_to_find_vqs into INTx and MSI-X variants virtio_pci: merge vp_free_vectors into vp_del_vqs ...
2016-12-16Makefile: drop -D__CHECK_ENDIAN__ from cflagsMichael S. Tsirkin29-52/+3
That's the default now, no need for makefiles to set it. Signed-off-by: Michael S. Tsirkin <[email protected]> Acked-by: Kalle Valo <[email protected]> Acked-by: Marcel Holtmann <[email protected]> Acked-by: Marc Kleine-Budde <[email protected]> Acked-by: Greg Kroah-Hartman <[email protected]> Acked-by: Arend van Spriel <[email protected]>
2016-12-16linux: drop __bitwise__ everywhereMichael S. Tsirkin2-3/+3
__bitwise__ used to mean "yes, please enable sparse checks unconditionally", but now that we dropped __CHECK_ENDIAN__ __bitwise is exactly the same. There aren't many users, replace it by __bitwise everywhere. Signed-off-by: Michael S. Tsirkin <[email protected]> Acked-by: Greg Kroah-Hartman <[email protected]> Acked-by: Stefan Schmidt <[email protected]> Acked-by: Krzysztof Kozlowski <[email protected]> Akced-by: Lee Duncan <[email protected]>
2016-12-15Merge tag 'pci-v4.10-changes' of ↵Linus Torvalds1-41/+43
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci Pull PCI updates from Bjorn Helgaas: "PCI changes: - add support for PCI on ARM64 boxes with ACPI. We already had this for theoretical spec-compliant hardware; now we're adding quirks for the actual hardware (Cavium, HiSilicon, Qualcomm, X-Gene) - add runtime PM support for hotplug ports - enable runtime suspend for Intel UHCI that uses platform-specific wakeup signaling - add yet another host bridge registration interface. We hope this is extensible enough to subsume the others - expose device revision in sysfs for DRM - to avoid device conflicts, make sure any VF BAR updates are done before enabling the VF - avoid unnecessary link retrains for ASPM - allow INTx masking on Mellanox devices that support it - allow access to non-standard VPD for Chelsio devices - update Broadcom iProc support for PAXB v2, PAXC v2, inbound DMA, etc - update Rockchip support for max-link-speed - add NVIDIA Tegra210 support - add Layerscape LS1046a support - update R-Car compatibility strings - add Qualcomm MSM8996 support - remove some uninformative bootup messages" * tag 'pci-v4.10-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (115 commits) PCI: Enable access to non-standard VPD for Chelsio devices (cxgb3) PCI: Expand "VPD access disabled" quirk message PCI: pciehp: Remove loading message PCI: hotplug: Remove hotplug core message PCI: Remove service driver load/unload messages PCI/AER: Log AER IRQ when claiming Root Port PCI/AER: Log errors with PCI device, not PCIe service device PCI/AER: Remove unused version macros PCI/PME: Log PME IRQ when claiming Root Port PCI/PME: Drop unused support for PMEs from Root Complex Event Collectors PCI: Move config space size macros to pci_regs.h x86/platform/intel-mid: Constify mid_pci_platform_pm PCI/ASPM: Don't retrain link if ASPM not possible PCI: iproc: Skip check for legacy IRQ on PAXC buses PCI: pciehp: Leave power indicator on when enabling already-enabled slot PCI: pciehp: Prioritize data-link event over presence detect PCI: rcar: Add gen3 fallback compatibility string for pcie-rcar PCI: rcar: Use gen2 fallback compatibility last PCI: rcar-gen2: Use gen2 fallback compatibility last PCI: rockchip: Move the deassert of pm/aclk/pclk after phy_init() ..
2016-12-15Merge tag 'for-linus' of ↵Linus Torvalds2-4/+3
git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma Pull rdma updates from Doug Ledford: "This is the complete update for the rdma stack for this release cycle. Most of it is typical driver and core updates, but there is the entirely new VMWare pvrdma driver. You may have noticed that there were changes in DaveM's pull request to the bnxt Ethernet driver to support a RoCE RDMA driver. The bnxt_re driver was tentatively set to be pulled in this release cycle, but it simply wasn't ready in time and was dropped (a few review comments still to address, and some multi-arch build issues like prefetch() not working across all arches). Summary: - shared mlx5 updates with net stack (will drop out on merge if Dave's tree has already been merged) - driver updates: cxgb4, hfi1, hns-roce, i40iw, mlx4, mlx5, qedr, rxe - debug cleanups - new connection rejection helpers - SRP updates - various misc fixes - new paravirt driver from vmware" * tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (210 commits) IB: Add vmw_pvrdma driver IB/mlx4: fix improper return value IB/ocrdma: fix bad initialization infiniband: nes: return value of skb_linearize should be handled MAINTAINERS: Update Intel RDMA RNIC driver maintainers MAINTAINERS: Remove Mitesh Ahuja from emulex maintainers IB/core: fix unmap_sg argument qede: fix general protection fault may occur on probe IB/mthca: Replace pci_pool_alloc by pci_pool_zalloc mlx5, calc_sq_size(): Make a debug message more informative mlx5: Remove a set-but-not-used variable mlx5: Use { } instead of { 0 } to init struct IB/srp: Make writing the add_target sysfs attr interruptible IB/srp: Make mapping failures easier to debug IB/srp: Make login failures easier to debug IB/srp: Introduce a local variable in srp_add_one() IB/srp: Fix CONFIG_DYNAMIC_DEBUG=n build IB/multicast: Check ib_find_pkey() return value IPoIB: Avoid reading an uninitialized member variable IB/mad: Fix an array index check ...
2016-12-14Merge branch 'akpm' (patches from Andrew)Linus Torvalds3-30/+57
Merge more updates from Andrew Morton: - a few misc things - kexec updates - DMA-mapping updates to better support networking DMA operations - IPC updates - various MM changes to improve DAX fault handling - lots of radix-tree changes, mainly to the test suite. All leading up to reimplementing the IDA/IDR code to be a wrapper layer over the radix-tree. However the final trigger-pulling patch is held off for 4.11. * emailed patches from Andrew Morton <[email protected]>: (114 commits) radix tree test suite: delete unused rcupdate.c radix tree test suite: add new tag check radix-tree: ensure counts are initialised radix tree test suite: cache recently freed objects radix tree test suite: add some more functionality idr: reduce the number of bits per level from 8 to 6 rxrpc: abstract away knowledge of IDR internals tpm: use idr_find(), not idr_find_slowpath() idr: add ida_is_empty radix tree test suite: check multiorder iteration radix-tree: fix replacement for multiorder entries radix-tree: add radix_tree_split_preload() radix-tree: add radix_tree_split radix-tree: add radix_tree_join radix-tree: delete radix_tree_range_tag_if_tagged() radix-tree: delete radix_tree_locate_item() radix-tree: improve multiorder iterators btrfs: fix race in btrfs_free_dummy_fs_info() radix-tree: improve dump output radix-tree: make radix_tree_find_next_bit more useful ...
2016-12-14drivers/net/wireless/intel/iwlwifi/dvm/calib.c: simplfy min() expressionAndrew Morton1-2/+1
This cast is no longer needed. Cc: Johannes Berg <[email protected]> Cc: Emmanuel Grumbach <[email protected]> Cc: Intel Linux Wireless <[email protected]> Cc: Kalle Valo <[email protected]> Signed-off-by: Andrew Morton <[email protected]> Signed-off-by: Linus Torvalds <[email protected]>
2016-12-14igb: update code to better handle incrementing page countAlexander Duyck2-8/+23
Update the driver code so that we do bulk updates of the page reference count instead of just incrementing it by one reference at a time. The advantage to doing this is that we cut down on atomic operations and this in turn should give us a slight improvement in cycles per packet. In addition if we eventually move this over to using build_skb the gains will be more noticeable. Link: http://lkml.kernel.org/r/[email protected] Signed-off-by: Alexander Duyck <[email protected]> Acked-by: Jeff Kirsher <[email protected]> Cc: "David S. Miller" <[email protected]> Cc: "James E.J. Bottomley" <[email protected]> Cc: Chris Metcalf <[email protected]> Cc: David Howells <[email protected]> Cc: Geert Uytterhoeven <[email protected]> Cc: Hans-Christian Noren Egtvedt <[email protected]> Cc: Helge Deller <[email protected]> Cc: James Hogan <[email protected]> Cc: Jonas Bonn <[email protected]> Cc: Keguang Zhang <[email protected]> Cc: Ley Foon Tan <[email protected]> Cc: Mark Salter <[email protected]> Cc: Max Filippov <[email protected]> Cc: Michael Ellerman <[email protected]> Cc: Michal Simek <[email protected]> Cc: Ralf Baechle <[email protected]> Cc: Rich Felker <[email protected]> Cc: Richard Kuo <[email protected]> Cc: Russell King <[email protected]> Cc: Steven Miao <[email protected]> Cc: Tobias Klauser <[email protected]> Cc: Vineet Gupta <[email protected]> Cc: Yoshinori Sato <[email protected]> Signed-off-by: Andrew Morton <[email protected]> Signed-off-by: Linus Torvalds <[email protected]>
2016-12-14igb: update driver to make use of DMA_ATTR_SKIP_CPU_SYNCAlexander Duyck1-20/+33
The ARM architecture provides a mechanism for deferring cache line invalidation in the case of map/unmap. This patch makes use of this mechanism to avoid unnecessary synchronization. A secondary effect of this change is that the portion of the page that has been synchronized for use by the CPU should be writable and could be passed up the stack (at least on ARM). The last bit that occurred to me is that on architectures where the sync_for_cpu call invalidates cache lines we were prefetching and then invalidating the first 128 bytes of the packet. To avoid that I have moved the sync up to before we perform the prefetch and allocate the skbuff so that we can actually make use of it. Link: http://lkml.kernel.org/r/[email protected] Signed-off-by: Alexander Duyck <[email protected]> Acked-by: Jeff Kirsher <[email protected]> Cc: "David S. Miller" <[email protected]> Cc: "James E.J. Bottomley" <[email protected]> Cc: Chris Metcalf <[email protected]> Cc: David Howells <[email protected]> Cc: Geert Uytterhoeven <[email protected]> Cc: Hans-Christian Noren Egtvedt <[email protected]> Cc: Helge Deller <[email protected]> Cc: James Hogan <[email protected]> Cc: Jonas Bonn <[email protected]> Cc: Keguang Zhang <[email protected]> Cc: Ley Foon Tan <[email protected]> Cc: Mark Salter <[email protected]> Cc: Max Filippov <[email protected]> Cc: Michael Ellerman <[email protected]> Cc: Michal Simek <[email protected]> Cc: Ralf Baechle <[email protected]> Cc: Rich Felker <[email protected]> Cc: Richard Kuo <[email protected]> Cc: Russell King <[email protected]> Cc: Steven Miao <[email protected]> Cc: Tobias Klauser <[email protected]> Cc: Vineet Gupta <[email protected]> Cc: Yoshinori Sato <[email protected]> Signed-off-by: Andrew Morton <[email protected]> Signed-off-by: Linus Torvalds <[email protected]>
2016-12-14scsi: cxgb4i: libcxgbi: cxgb4: add T6 iSCSI completion featureVarun Prakash1-0/+13
T6 adapters reduce number of completions to host by generating single completion for all the directly placed(DDP) iSCSI pdus in a sequence. This patch adds new structure for completion hw cmd (struct cpl_rx_iscsi_cmp) and implements T6 completion feature. Signed-off-by: Varun Prakash <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]>
2016-12-14Merge branch 'vmw_pvrdma' into merge-testDoug Ledford1-2/+1
2016-12-14Merge branches 'misc', 'qedr', 'reject-helpers', 'rxe' and 'srp' into merge-testDoug Ledford1-2/+2
2016-12-14qede: fix general protection fault may occur on probeAmrani, Ram1-2/+2
The recent introduction of qedr driver support in qede causes a GPF when probing the driver in a server without a RoCE enabled QLogic NIC. This fix avoids using an uninitialized pointer in such a case. Caught by the kernel test robot. Signed-off-by: Ram Amrani <[email protected]> Signed-off-by: Doug Ledford <[email protected]>
2016-12-14Merge branch 'for-linus' of ↵Linus Torvalds6-7/+7
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial Pull trivial updates from Jiri Kosina. * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: NTB: correct ntb_spad_count comment typo misc: ibmasm: fix typo in error message Remove references to dead make variable LINUX_INCLUDE Remove last traces of ikconfig.h treewide: Fix printk() message errors Documentation/device-mapper: s/getsize/getsz/
2016-12-14IB/mlx4: avoid a -Wmaybe-uninitialize warningArnd Bergmann1-2/+3
There is an old warning about mlx4_SW2HW_EQ_wrapper on x86: ethernet/mellanox/mlx4/resource_tracker.c: In function ‘mlx4_SW2HW_EQ_wrapper’: ethernet/mellanox/mlx4/resource_tracker.c:3071:10: error: ‘eq’ may be used uninitialized in this function [-Werror=maybe-uninitialized] The problem here is that gcc won't track the state of the variable across a spin_unlock. Moving the assignment out of the lock is safe here and avoids the warning. Signed-off-by: Arnd Bergmann <[email protected]> Reviewed-by: Yishai Hadas <[email protected]> Signed-off-by: Doug Ledford <[email protected]>
2016-12-14treewide: Fix printk() message errorsMasanari Iida6-7/+7
This patch fix spelling typos in printk and kconfig. Signed-off-by: Masanari Iida <[email protected]> Acked-by: Randy Dunlap <[email protected]> Signed-off-by: Jiri Kosina <[email protected]>
2016-12-13Merge tag 'for-linus-4.10-rc0-tag' of ↵Linus Torvalds2-86/+33
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip Pull xen updates from Juergen Gross: "Xen features and fixes for 4.10 These are some fixes, a move of some arm related headers to share them between arm and arm64 and a series introducing a helper to make code more readable. The most notable change is David stepping down as maintainer of the Xen hypervisor interface. This results in me sending you the pull requests for Xen related code from now on" * tag 'for-linus-4.10-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: (29 commits) xen/balloon: Only mark a page as managed when it is released xenbus: fix deadlock on writes to /proc/xen/xenbus xen/scsifront: don't request a slot on the ring until request is ready xen/x86: Increase xen_e820_map to E820_X_MAX possible entries x86: Make E820_X_MAX unconditionally larger than E820MAX xen/pci: Bubble up error and fix description. xen: xenbus: set error code on failure xen: set error code on failures arm/xen: Use alloc_percpu rather than __alloc_percpu arm/arm64: xen: Move shared architecture headers to include/xen/arm xen/events: use xen_vcpu_id mapping for EVTCHNOP_status xen/gntdev: Use VM_MIXEDMAP instead of VM_IO to avoid NUMA balancing xen-scsifront: Add a missing call to kfree MAINTAINERS: update XEN HYPERVISOR INTERFACE xenfs: Use proc_create_mount_point() to create /proc/xen xen-platform: use builtin_pci_driver xen-netback: fix error handling output xen: make use of xenbus_read_unsigned() in xenbus xen: make use of xenbus_read_unsigned() in xen-pciback xen: make use of xenbus_read_unsigned() in xen-fbfront ...
2016-12-13Merge tag 'staging-4.10-rc1' of ↵Linus Torvalds1-1/+0
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging Pull staging/IIO updates from Greg KH: "Here's the "big" staging/iio pull request for 4.10-rc1. Not as big as 4.9 was, but still just over a thousand changes. We almost broke even of lines added vs. removed, as the slicoss driver was removed (got a "clean" driver for the same hardware through the netdev tree), and some iio drivers were also dropped, but I think we ended up adding a few thousand lines to the source tree in the end. Other than that it's a lot of minor fixes all over the place, nothing major stands out at all. All of these have been in linux-next for a while. There will be a merge conflict with Al's vfs tree in the lustre code, but the resolution for that should be pretty simple, that too has been in linux-next" * tag 'staging-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1002 commits) staging: comedi: comedidev.h: Document usage of 'detach' handler staging: fsl-mc: remove unnecessary info prints from bus driver staging: fsl-mc: add sysfs ABI doc staging/lustre/o2iblnd: Fix misspelled attemps->attempts staging/lustre/o2iblnd: Fix misspelling intialized->intialized staging/lustre: Convert all bare unsigned to unsigned int staging/lustre/socklnd: Fix whitespace problem staging/lustre/o2iblnd: Add missing space staging/lustre/lnetselftest: Fix potential integer overflow staging: greybus: audio_module: remove redundant OOM message staging: dgnc: Fix lines longer than 80 characters staging: dgnc: fix blank line after '{' warnings. staging/android: remove Sync Framework tasks from TODO staging/lustre/osc: Revert erroneous list_for_each_entry_safe use staging: slicoss: remove the staging driver staging: lustre: libcfs: remove lnet upcall code staging: lustre: remove set but unused variables staging: lustre: osc: set lock data for readahead lock staging: lustre: import: don't reconnect during connect interpret staging: lustre: clio: remove mtime check in vvp_io_fault_start() ...
2016-12-13Merge tag 'pm-4.10-rc1' of ↵Linus Torvalds1-0/+6
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm Pull power management updates from Rafael Wysocki: "Again, cpufreq gets more changes than the other parts this time (one new driver, one old driver less, a bunch of enhancements of the existing code, new CPU IDs, fixes, cleanups) There also are some changes in cpuidle (idle injection rework, a couple of new CPU IDs, online/offline rework in intel_idle, fixes and cleanups), in the generic power domains framework (mostly related to supporting power domains containing CPUs), and in the Operating Performance Points (OPP) library (mostly related to supporting devices with multiple voltage regulators) In addition to that, the system sleep state selection interface is modified to make it easier for distributions with unchanged user space to support suspend-to-idle as the default system suspend method, some issues are fixed in the PM core, the latency tolerance PM QoS framework is improved a bit, the Intel RAPL power capping driver is cleaned up and there are some fixes and cleanups in the devfreq subsystem Specifics: - New cpufreq driver for Broadcom STB SoCs and a Device Tree binding for it (Markus Mayer) - Support for ARM Integrator/AP and Integrator/CP in the generic DT cpufreq driver and elimination of the old Integrator cpufreq driver (Linus Walleij) - Support for the zx296718, r8a7743 and r8a7745, Socionext UniPhier, and PXA SoCs in the the generic DT cpufreq driver (Baoyou Xie, Geert Uytterhoeven, Masahiro Yamada, Robert Jarzmik) - cpufreq core fix to eliminate races that may lead to using inactive policy objects and related cleanups (Rafael Wysocki) - cpufreq schedutil governor update to make it use SCHED_FIFO kernel threads (instead of regular workqueues) for doing delayed work (to reduce the response latency in some cases) and related cleanups (Viresh Kumar) - New cpufreq sysfs attribute for resetting statistics (Markus Mayer) - cpufreq governors fixes and cleanups (Chen Yu, Stratos Karafotis, Viresh Kumar) - Support for using generic cpufreq governors in the intel_pstate driver (Rafael Wysocki) - Support for per-logical-CPU P-state limits and the EPP/EPB (Energy Performance Preference/Energy Performance Bias) knobs in the intel_pstate driver (Srinivas Pandruvada) - New CPU ID for Knights Mill in intel_pstate (Piotr Luc) - intel_pstate driver modification to use the P-state selection algorithm based on CPU load on platforms with the system profile in the ACPI tables set to "mobile" (Srinivas Pandruvada) - intel_pstate driver cleanups (Arnd Bergmann, Rafael Wysocki, Srinivas Pandruvada) - cpufreq powernv driver updates including fast switching support (for the schedutil governor), fixes and cleanus (Akshay Adiga, Andrew Donnellan, Denis Kirjanov) - acpi-cpufreq driver rework to switch it over to the new CPU offline/online state machine (Sebastian Andrzej Siewior) - Assorted cleanups in cpufreq drivers (Wei Yongjun, Prashanth Prakash) - Idle injection rework (to make it use the regular idle path instead of a home-grown custom one) and related powerclamp thermal driver updates (Peter Zijlstra, Jacob Pan, Petr Mladek, Sebastian Andrzej Siewior) - New CPU IDs for Atom Z34xx and Knights Mill in intel_idle (Andy Shevchenko, Piotr Luc) - intel_idle driver cleanups and switch over to using the new CPU offline/online state machine (Anna-Maria Gleixner, Sebastian Andrzej Siewior) - cpuidle DT driver update to support suspend-to-idle properly (Sudeep Holla) - cpuidle core cleanups and misc updates (Daniel Lezcano, Pan Bian, Rafael Wysocki) - Preliminary support for power domains including CPUs in the generic power domains (genpd) framework and related DT bindings (Lina Iyer) - Assorted fixes and cleanups in the generic power domains (genpd) framework (Colin Ian King, Dan Carpenter, Geert Uytterhoeven) - Preliminary support for devices with multiple voltage regulators and related fixes and cleanups in the Operating Performance Points (OPP) library (Viresh Kumar, Masahiro Yamada, Stephen Boyd) - System sleep state selection interface rework to make it easier to support suspend-to-idle as the default system suspend method (Rafael Wysocki) - PM core fixes and cleanups, mostly related to the interactions between the system suspend and runtime PM frameworks (Ulf Hansson, Sahitya Tummala, Tony Lindgren) - Latency tolerance PM QoS framework imorovements (Andrew Lutomirski) - New Knights Mill CPU ID for the Intel RAPL power capping driver (Piotr Luc) - Intel RAPL power capping driver fixes, cleanups and switch over to using the new CPU offline/online state machine (Jacob Pan, Thomas Gleixner, Sebastian Andrzej Siewior) - Fixes and cleanups in the exynos-ppmu, exynos-nocp, rk3399_dmc, rockchip-dfi devfreq drivers and the devfreq core (Axel Lin, Chanwoo Choi, Javier Martinez Canillas, MyungJoo Ham, Viresh Kumar) - Fix for false-positive KASAN warnings during resume from ACPI S3 (suspend-to-RAM) on x86 (Josh Poimboeuf) - Memory map verification during resume from hibernation on x86 to ensure a consistent address space layout (Chen Yu) - Wakeup sources debugging enhancement (Xing Wei) - rockchip-io AVS driver cleanup (Shawn Lin)" * tag 'pm-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (127 commits) devfreq: rk3399_dmc: Don't use OPP structures outside of RCU locks devfreq: rk3399_dmc: Remove dangling rcu_read_unlock() devfreq: exynos: Don't use OPP structures outside of RCU locks Documentation: intel_pstate: Document HWP energy/performance hints cpufreq: intel_pstate: Support for energy performance hints with HWP cpufreq: intel_pstate: Add locking around HWP requests PM / sleep: Print active wakeup sources when blocking on wakeup_count reads PM / core: Fix bug in the error handling of async suspend PM / wakeirq: Fix dedicated wakeirq for drivers not using autosuspend PM / Domains: Fix compatible for domain idle state PM / OPP: Don't WARN on multiple calls to dev_pm_opp_set_regulators() PM / OPP: Allow platform specific custom set_opp() callbacks PM / OPP: Separate out _generic_set_opp() PM / OPP: Add infrastructure to manage multiple regulators PM / OPP: Pass struct dev_pm_opp_supply to _set_opp_voltage() PM / OPP: Manage supply's voltage/current in a separate structure PM / OPP: Don't use OPP structure outside of rcu protected section PM / OPP: Reword binding supporting multiple regulators per device PM / OPP: Fix incorrect cpu-supply property in binding cpuidle: Add a kerneldoc comment to cpuidle_use_deepest_state() ..
Powered by cgit, Gruvboxed by Blaster4385.