aboutsummaryrefslogtreecommitdiff
path: root/drivers/net
AgeCommit message (Collapse)AuthorFilesLines
2023-08-25wifi: rtw89: initialize multi-channel handlingZong-Zhe Yang6-23/+219
We prepare to deal with multiple channels via new entity modes. * MCC_PREPARE: Transitional mode before MCC * MCC: Multi-Channel Concurrent mode And, enum of sub-entity is extended for second channel context. We add the entry flow of multi-channel handling and the core stuffs for extended index of sub-entity. And, we now deal with the filling of entity channels' info in entity recalc where we know the number of active chanctx. However, the other detail coding of MCC start/stop will be implemented in the following. Besides, chanctx listener struct is pre-added in chip info. Each component can add callback type in chanctx listener and configure its callback function to react according to chanctx states. We know at least RFK (RF calibration) and BTC (BT coexistence) will require such callbacks. Signed-off-by: Zong-Zhe Yang <[email protected]> Signed-off-by: Ping-Ke Shih <[email protected]> Signed-off-by: Kalle Valo <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2023-08-25wifi: rtw89: provide functions to configure NoA for beacon updateZong-Zhe Yang4-0/+102
Callers call renew function when wanting to generate a new P2P NoA information element, and call append function to append NoA attribute one by one. Then, updating beacon work will fetch the P2P NoA information element configured by callers and add it to beacon. The use case of MCC (multi-channel concurrent) <GO + STA> for example: * start MCC - GO part renew P2P NoA append period NoA after calculation * download beacon for GO fetch P2P NoA and add to beacon content * stop MCC - GO part renew P2P NoA (reset) Signed-off-by: Zong-Zhe Yang <[email protected]> Signed-off-by: Ping-Ke Shih <[email protected]> Signed-off-by: Kalle Valo <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2023-08-25wifi: rtw89: call rtw89_chan_get() by vif chanctx if aware of vifZong-Zhe Yang6-22/+45
We adjust these processes which can work accodrding to vif but call rtw89_chan_get() with static RTW89_SUB_ENTITY_0. After multi-channel support, chanctx of vif won't always be on RTW89_SUB_ENTITY_0. So, we make them call rtw89_chan_get() with rtwvif->sub_entity_idx. Signed-off-by: Zong-Zhe Yang <[email protected]> Signed-off-by: Ping-Ke Shih <[email protected]> Signed-off-by: Kalle Valo <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2023-08-25wifi: rtw89: sar: let caller decide the center frequency to queryZong-Zhe Yang4-21/+27
If multiple channels, SAR will be hard to determine the center frequency to query. Therefore, we move this decision out of SAR. Signed-off-by: Zong-Zhe Yang <[email protected]> Signed-off-by: Ping-Ke Shih <[email protected]> Signed-off-by: Kalle Valo <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2023-08-25wifi: rtw89: refine rtw89_correct_cck_chan() by rtw89_hw_to_nl80211_band()Zong-Zhe Yang1-2/+1
In rtw89_correct_cck_chan(), we turn to use rtw89_hw_to_nl80211_band(). The difference between rtw89_hw_to_nl80211_band() and the original raw judgement is the case on 6 GHz. Since rtw89_correct_cck_chan() is common code independent on chip, if runtime chip doesn't support 6 GHz, it is probably safe. Otherwise, it might not. Signed-off-by: Zong-Zhe Yang <[email protected]> Signed-off-by: Ping-Ke Shih <[email protected]> Signed-off-by: Kalle Valo <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2023-08-25wifi: rtw89: add function prototype for coex request durationZong-Zhe Yang3-0/+42
The request duration comes from coex mechanism, indicating the length of time that should be reserved for BT in each time division. It is required to handle update notification when channel concurrency processes. Since it will involve in both coex and wifi code flow, this commit ahead adds the prototype for required function interfaces to split the implementation of coex and wifi in the following. The follow-up are expected be add afterwards. 1. coex mechanism call rtw89_core_ntfy_btc_event() once bt req len changes 2. channel concurrency flow updates related stuffs when notified Signed-off-by: Zong-Zhe Yang <[email protected]> Signed-off-by: Ping-Ke Shih <[email protected]> Signed-off-by: Kalle Valo <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2023-08-25Fix nomenclature for USB and PCI wireless devicesAlan Stern20-32/+32
A mouse that uses a USB connection is called a "USB mouse" device (or "USB mouse" for short), not a "mouse USB" device. By analogy, a WiFi adapter that connects to the host computer via USB is a "USB wireless" device, not a "wireless USB" device. (The latter term more properly refers to a defunct Wireless USB specification, which described a technology for sending USB protocol messages over an ultra wideband radio link.) Similarly for a WiFi adapter card that plugs into a PCIe slot: It is a "PCIe wireless" device, not a "wireless PCIe" device. Rephrase the text in the kernel source where the word ordering is wrong. Signed-off-by: Alan Stern <[email protected]> Reviewed-by: Greg Kroah-Hartman <[email protected]> Signed-off-by: Kalle Valo <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2023-08-25mlxsw: core_hwmon: Adjust module label names based on MTCAP sensor counterVadim Pasternak1-1/+2
Transceiver module temperature sensors are indexed after ASIC and platform sensors. The current label printing method does not take this into account and simply prints the index of the transceiver module sensor. On new systems that have platform sensors this results in incorrect (shifted) transceiver module labels being printed: $ sensors [...] front panel 002: +37.0°C (crit = +70.0°C, emerg = +75.0°C) front panel 003: +47.0°C (crit = +70.0°C, emerg = +75.0°C) [...] Fix by taking the sensor count into account. After the fix: $ sensors [...] front panel 001: +37.0°C (crit = +70.0°C, emerg = +75.0°C) front panel 002: +47.0°C (crit = +70.0°C, emerg = +75.0°C) [...] Fixes: a53779de6a0e ("mlxsw: core: Add QSFP module temperature label attribute to hwmon") Signed-off-by: Vadim Pasternak <[email protected]> Reviewed-by: Ido Schimmel <[email protected]> Signed-off-by: Petr Machata <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2023-08-25mlxsw: i2c: Limit single transaction buffer sizeVadim Pasternak1-1/+2
Maximum size of buffer is obtained from underlying I2C adapter and in case adapter allows I2C transaction buffer size greater than 100 bytes, transaction will fail due to firmware limitation. As a result driver will fail initialization. Limit the maximum size of transaction buffer by 100 bytes to fit to firmware. Remove unnecessary calculation: max_t(u16, MLXSW_I2C_BLK_DEF, quirk_size). This condition can not happened. Fixes: 3029a693beda ("mlxsw: i2c: Allow flexible setting of I2C transactions size") Signed-off-by: Vadim Pasternak <[email protected]> Reviewed-by: Petr Machata <[email protected]> Signed-off-by: Petr Machata <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2023-08-25mlxsw: i2c: Fix chunk size setting in output mailbox bufferVadim Pasternak1-1/+1
The driver reads commands output from the output mailbox. If the size of the output mailbox is not a multiple of the transaction / block size, then the driver will not issue enough read transactions to read the entire output, which can result in driver initialization errors. Fix by determining the number of transactions using DIV_ROUND_UP(). Fixes: 3029a693beda ("mlxsw: i2c: Allow flexible setting of I2C transactions size") Signed-off-by: Vadim Pasternak <[email protected]> Reviewed-by: Ido Schimmel <[email protected]> Signed-off-by: Petr Machata <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2023-08-25net: arcnet: Do not call kfree_skb() under local_irq_disable()Jinjie Ruan1-1/+1
It is not allowed to call kfree_skb() from hardware interrupt context or with hardware interrupts being disabled. So replace kfree_skb() with dev_kfree_skb_irq() under local_irq_disable(). Compile tested only. Fixes: 05fcd31cc472 ("arcnet: add err_skb package for package status feedback") Signed-off-by: Jinjie Ruan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2023-08-25octeontx2-pf: fix page_pool creation fail for rings > 32kRatheesh Kannoth2-1/+3
octeontx2 driver calls page_pool_create() during driver probe() and fails if queue size > 32k. Page pool infra uses these buffers as shock absorbers for burst traffic. These pages are pinned down over time as working sets varies, due to the recycling nature of page pool, given page pool (currently) don't have a shrinker mechanism, the pages remain pinned down in ptr_ring. Instead of clamping page_pool size to 32k at most, limit it even more to 2k to avoid wasting memory. This have been tested on octeontx2 CN10KA hardware. TCP and UDP tests using iperf shows no performance regressions. Fixes: b2e3406a38f0 ("octeontx2-pf: Add support for page pool") Suggested-by: Alexander Lobakin <[email protected]> Reviewed-by: Sunil Goutham <[email protected]> Signed-off-by: Ratheesh Kannoth <[email protected]> Acked-by: Jesper Dangaard Brouer <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2023-08-25net: fec: add statistics for XDP_TXWei Fang1-1/+4
The FEC driver supports the statistics for XDP actions except for XDP_TX before, because the XDP_TX was not supported when adding the statistics for XDP. Now the FEC driver has supported XDP_TX since commit f601899e4321 ("net: fec: add XDP_TX feature support"). So it's reasonable and necessary to add statistics for XDP_TX. Signed-off-by: Wei Fang <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2023-08-25ice: avoid executing commands on other ports when driving syncJacob Keller2-6/+52
The ice hardware has a synchronization mechanism used to drive the simultaneous application of commands on both PHY ports and the source timer in the MAC. When issuing a sync via ice_ptp_exec_tmr_cmd(), the hardware will simultaneously apply the commands programmed for the main timer and each PHY port. Neither the main timer command register, nor the PHY port command registers auto clear on command execution. During the execution of a timer command intended for a single port on E822 devices, such as those used to configure a PHY during link up, the driver is not correctly clearing the previous commands. This results in unintentionally executing the last programmed command on the main timer and other PHY ports whenever performing reconfiguration on E822 ports after link up. This results in unintended side effects on other timers, depending on what command was previously programmed. To fix this, the driver must ensure that the main timer and all other PHY ports are properly initialized to perform no action. The enumeration for timer commands does not include an enumeration value for doing nothing. Introduce ICE_PTP_NOP for this purpose. When writing a timer command to hardware, leave the command bits set to zero which indicates that no operation should be performed on that port. Modify ice_ptp_one_port_cmd() to always initialize all ports. For all ports other than the one being configured, write their timer command register to ICE_PTP_NOP. This ensures that no side effect happens on the timer command. To fix this for the PHY ports, modify ice_ptp_one_port_cmd() to always initialize all other ports to ICE_PTP_NOP. This ensures that no side effects happen on the other ports. Call ice_ptp_src_cmd() with a command value if ICE_PTP_NOP in ice_sync_phy_timer_e822() and ice_start_phy_timer_e822(). With both of these changes, the driver should no longer execute a stale command on the main timer or another PHY port when reconfiguring one of the PHY ports after link up. Fixes: 3a7496234d17 ("ice: implement basic E822 PTP support") Signed-off-by: Siddaraju DH <[email protected]> Signed-off-by: Jacob Keller <[email protected]> Tested-by: Sunitha Mekala <[email protected]> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <[email protected]> Reviewed-by: Simon Horman <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2023-08-25wifi: ath: Use is_multicast_ether_addr() to check multicast Ether addressRuan Jinjie1-1/+1
Use is_multicast_ether_addr() to perform the Checking. Signed-off-by: Ruan Jinjie <[email protected]> Reviewed-by: Jeff Johnson <[email protected]> Signed-off-by: Kalle Valo <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2023-08-25wifi: ath12k: Remove unused declarationsYue Haibing4-8/+0
Commit d889913205cf ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices") declared but never implemented these, remove it. Signed-off-by: Yue Haibing <[email protected]> Acked-by: Jeff Johnson <[email protected]> Signed-off-by: Kalle Valo <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2023-08-25wifi: ath12k: add check max message length while scanning with extraieWen Gong1-7/+13
Currently the extraie length is directly used to allocate skb buffer. When the length of skb is greater than the max message length which firmware supports, error will happen in firmware side. Hence add check for the skb length and drop extraie when overflow and print a message. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 Signed-off-by: Wen Gong <[email protected]> Reviewed-by: Jeff Johnson <[email protected]> Signed-off-by: Kalle Valo <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2023-08-25wifi: ath9k: use IS_ERR() with debugfs_create_dir()Wang Ming1-1/+1
The debugfs_create_dir() function returns error pointers, it never returns NULL. Most incorrect error checks were fixed, but the one in ath9k_htc_init_debug() was forgotten. Fix the remaining error check. Fixes: e5facc75fa91 ("ath9k_htc: Cleanup HTC debugfs") Signed-off-by: Wang Ming <[email protected]> Acked-by: Toke Høiland-Jørgensen <[email protected]> Signed-off-by: Kalle Valo <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2023-08-25net: ngbe: move mdio access registers to libwxJiawen Wu2-61/+42
Registers of mdio accessing are common defined in libwx, remove the redundant macro definitions in ngbe driver. Signed-off-by: Jiawen Wu <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2023-08-25net: txgbe: support copper NIC with external PHYJiawen Wu5-22/+221
Wangxun SP chip supports to connect with external PHY (marvell 88x3310), which links to 10GBASE-T/1000BASE-T/100BASE-T. Add the identification of media types from subsystem device IDs. For sp_media_copper, register mdio bus for the external PHY. Signed-off-by: Jiawen Wu <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2023-08-25net: txgbe: support switching mode to 1000BASE-X and SGMIIJiawen Wu4-1/+61
Disable data path before PCS VR reset while switching PCS mode, to prevent the blocking of data path. Enable AN interrupt for CL37 auto-negotiation. Signed-off-by: Jiawen Wu <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2023-08-25net: txgbe: add FW version warningJiawen Wu1-0/+3
Since XPCS device identifier is implemented in the firmware version 0x20010 and above, so add a warning to prompt the users to upgrade the firmware to make sure the driver works. Signed-off-by: Jiawen Wu <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2023-08-25net: pcs: xpcs: adapt Wangxun NICs for SGMII modeJiawen Wu3-6/+52
Wangxun NICs support the connection with SFP to RJ45 module. In this case, PCS need to be configured in SGMII mode. According to chapter 6.11.1 "SGMII Auto-Negitiation" of DesignWare Cores Ethernet PCS (version 3.20a) and custom design manual, do the following configuration when the interface mode is SGMII. 1. program VR_MII_AN_CTRL bit(3) [TX_CONFIG] = 1b (PHY side SGMII) 2. program VR_MII_AN_CTRL bit(8) [MII_CTRL] = 1b (8-bit MII) 3. program VR_MII_DIG_CTRL1 bit(0) [PHY_MODE_CTRL] = 1b Also CL37 AN in backplane configurations need to be enabled because of the special hardware design. Another thing to note is that PMA needs to be reconfigured before each CL37 AN configuration for SGMII, otherwise AN will fail, although we don't know why. On this device, CL37_ANSGM_STS (bit[4:1] of VR_MII_AN_INTR_STS) indicates the status received from remote link during the auto-negotiation, and self-clear after the auto-negotiation is complete. Meanwhile, CL37_ANCMPLT_INTR will be set to 1, to indicate CL37 AN is complete. So add another way to get the state for CL37 SGMII. Signed-off-by: Jiawen Wu <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2023-08-25net: pcs: xpcs: add 1000BASE-X AN interrupt supportJiawen Wu2-1/+21
Enable CL37 AN complete interrupt for DW XPCS. It requires to clear the bit(0) [CL37_ANCMPLT_INTR] of VR_MII_AN_INTR_STS after AN completed. And there is a quirk for Wangxun devices to enable CL37 AN in backplane configurations because of the special hardware design. Signed-off-by: Jiawen Wu <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2023-08-25net: pcs: xpcs: support to switch mode for Wangxun NICsJiawen Wu4-6/+225
According to chapter 6 of DesignWare Cores Ethernet PCS (version 3.20a) and custom design manual, add a configuration flow for switching interface mode. If the interface changes, the following setting is required: 1. wait VR_XS_PCS_DIG_STS bit(4, 2) [PSEQ_STATE] = 100b (Power-Good) 2. write SR_XS_PCS_CTRL2 to select various PCS type 3. write SR_PMA_CTRL1 and/or SR_XS_PCS_CTRL1 for link speed 4. program PMA registers 5. write VR_XS_PCS_DIG_CTRL1 bit(15) [VR_RST] = 1b (Vendor-Specific Soft Reset) 6. wait for VR_XS_PCS_DIG_CTRL1 bit(15) [VR_RST] to get cleared Only 10GBASE-R/SGMII/1000BASE-X modes are planned for the current Wangxun devices. And there is a quirk for Wangxun devices to switch mode although the interface in phylink state has not changed, since PCS will change to default 10GBASE-R when the ethernet driver(txgbe) do LAN reset. Signed-off-by: Jiawen Wu <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2023-08-25net: pcs: xpcs: add specific vendor supoprt for Wangxun 10Gb NICsJiawen Wu1-3/+32
Since Wangxun 10Gb NICs require some special configuration on the IP of Synopsys Designware XPCS, introduce dev_flag for different vendors. Read OUI from device identifier registers, to detect Wangxun devices. And xpcs_soft_reset() is skipped to avoid the reset of device identifier registers. Signed-off-by: Jiawen Wu <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2023-08-24net/mlx5e: fix up for "net/mlx5e: Move MACsec flow steering operations to be ↵Stephen Rothwell1-0/+1
used as core library" Recent merge had a conflict in: drivers/net/ethernet/mellanox/mlx5/core/en_accel/macsec_fs.c between commit: aeb660171b06 ("net/mlx5e: fix double free in macsec_fs_tx_create_crypto_table_groups") from Linus' tree and commit: cb5ebe4896f9 ("net/mlx5e: Move MACsec flow steering operations to be used as core library") from the mlx5-next tree. This was missed and the former commit got lost, bring it back. Fixes: 3c5066c6b0a5 ("Merge branch 'mlx5-next' of https://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux") Signed-off-by: Stephen Rothwell <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2023-08-24net/mlx5: Dynamic cyclecounter shift calculation for PTP free running clockRahul Rameshbabu1-5/+27
Use a dynamic calculation to determine the shift value for the internal timer cyclecounter that will lead to the highest precision frequency adjustments. Previously used a constant for the shift value assuming all devices supported by the driver had a nominal frequency of 1GHz. However, there are devices that operate at different frequencies. The previous shift value constant would break the PHC functionality for those devices. Reported-by: Vadim Fedorenko <[email protected]> Closes: https://lore.kernel.org/netdev/[email protected]/ Fixes: 6a4010927562 ("net/mlx5: Update cyclecounter shift value to improve ptp free running mode precision") Signed-off-by: Rahul Rameshbabu <[email protected]> Tested-by: Vadim Fedorenko <[email protected]> Reviewed-by: Jacob Keller <[email protected]> Reviewed-by: Simon Horman <[email protected]> Acked-by: Saeed Mahameed <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2023-08-24minmax: add in_range() macroMatthew Wilcox (Oracle)1-9/+9
Patch series "New page table range API", v6. This patchset changes the API used by the MM to set up page table entries. The four APIs are: set_ptes(mm, addr, ptep, pte, nr) update_mmu_cache_range(vma, addr, ptep, nr) flush_dcache_folio(folio) flush_icache_pages(vma, page, nr) flush_dcache_folio() isn't technically new, but no architecture implemented it, so I've done that for them. The old APIs remain around but are mostly implemented by calling the new interfaces. The new APIs are based around setting up N page table entries at once. The N entries belong to the same PMD, the same folio and the same VMA, so ptep++ is a legitimate operation, and locking is taken care of for you. Some architectures can do a better job of it than just a loop, but I have hesitated to make too deep a change to architectures I don't understand well. One thing I have changed in every architecture is that PG_arch_1 is now a per-folio bit instead of a per-page bit when used for dcache clean/dirty tracking. This was something that would have to happen eventually, and it makes sense to do it now rather than iterate over every page involved in a cache flush and figure out if it needs to happen. The point of all this is better performance, and Fengwei Yin has measured improvement on x86. I suspect you'll see improvement on your architecture too. Try the new will-it-scale test mentioned here: https://lore.kernel.org/linux-mm/[email protected]/ You'll need to run it on an XFS filesystem and have CONFIG_TRANSPARENT_HUGEPAGE set. This patchset is the basis for much of the anonymous large folio work being done by Ryan, so it's received quite a lot of testing over the last few months. This patch (of 38): Determine if a value lies within a range more efficiently (subtraction + comparison vs two comparisons and an AND). It also has useful (under some circumstances) behaviour if the range exceeds the maximum value of the type. Convert all the conflicting definitions of in_range() within the kernel; some can use the generic definition while others need their own definition. Link: https://lkml.kernel.org/r/[email protected] Link: https://lkml.kernel.org/r/[email protected] Signed-off-by: Matthew Wilcox (Oracle) <[email protected]> Signed-off-by: Andrew Morton <[email protected]>
2023-08-24e1000e: Add support for the next LOM generationSasha Neftin5-0/+17
Add devices IDs for the next LOM generations that will be available on the next Intel Client platforms. This patch provides the initial support for these devices. Signed-off-by: Sasha Neftin <[email protected]> Tested-by: Naama Meir <[email protected]> Signed-off-by: Tony Nguyen <[email protected]>
2023-08-24igc: Decrease PTM short interval from 10 us to 1 usSasha Neftin1-1/+1
With the 10us interval, we were seeing PTM transactions take around 12us. Hardware team suggested this interval could be lowered to 1us which was confirmed with PCIe sniffer. With the 1us interval, PTM dialogs took around 2us. Suggested-by: Vinicius Costa Gomes <[email protected]> Signed-off-by: Sasha Neftin <[email protected]> Tested-by: Muhammad Husaini Zulkifli <[email protected]> Reviewed-by: Muhammad Husaini Zulkifli <[email protected]> Tested-by: Naama Meir <[email protected]> Signed-off-by: Tony Nguyen <[email protected]>
2023-08-24igc: Add support for multiple in-flight TX timestampsVinicius Costa Gomes6-63/+192
Add support for using the four sets of timestamping registers that i225/i226 have available for TX. In some workloads, where multiple applications request hardware transmission timestamps, it was possible that some of those requests were denied because the only in use register was already occupied. This is also in preparation to future support for hardware timestamping with multiple PTP domains. With multiple domains chances of multiple TX timestamps being requested at the same time increase. Before: $ sudo ./ntpperf -i enp3s0 -m 10:22:22:22:22:21 -d 192.168.1.3 -s 172.18.0.0/16 -I -H -o 37 | responses | TX timestamp offset (ns) rate clients | lost invalid basic xleave | min mean max stddev 1000 100 0.00% 0.00% 0.00% 100.00% +1 +41 +73 13 1500 150 0.00% 0.00% 0.00% 100.00% +9 +49 +87 15 2250 225 0.00% 0.00% 0.00% 100.00% +9 +42 +79 13 3375 337 0.00% 0.00% 0.00% 100.00% +11 +46 +81 13 5062 506 0.00% 0.00% 0.00% 100.00% +7 +44 +80 13 7593 759 0.00% 0.00% 0.00% 100.00% +9 +44 +79 12 11389 1138 0.00% 0.00% 0.00% 100.00% +14 +51 +87 13 17083 1708 0.00% 0.00% 0.00% 100.00% +1 +41 +80 14 25624 2562 0.00% 0.00% 0.00% 100.00% +11 +50 +5107 51 38436 3843 0.00% 0.00% 0.00% 100.00% -2 +36 +7843 38 57654 5765 0.00% 0.00% 0.00% 100.00% +4 +42 +10503 69 86481 8648 0.00% 0.00% 0.00% 100.00% +11 +54 +5492 65 129721 12972 0.00% 0.00% 0.00% 100.00% +31 +2680 +6942 2606 194581 16384 16.79% 0.00% 0.87% 82.34% +73 +4444 +15879 3116 291871 16384 35.05% 0.00% 1.53% 63.42% +188 +5381 +17019 3035 437806 16384 54.95% 0.00% 2.55% 42.50% +233 +6302 +13885 2846 After: $ sudo ./ntpperf -i enp3s0 -m 10:22:22:22:22:21 -d 192.168.1.3 -s 172.18.0.0/16 -I -H -o 37 | responses | TX timestamp offset (ns) rate clients | lost invalid basic xleave | min mean max stddev 1000 100 0.00% 0.00% 0.00% 100.00% -20 +12 +43 13 1500 150 0.00% 0.00% 0.00% 100.00% -23 +18 +57 14 2250 225 0.00% 0.00% 0.00% 100.00% -2 +33 +67 13 3375 337 0.00% 0.00% 0.00% 100.00% +1 +38 +76 13 5062 506 0.00% 0.00% 0.00% 100.00% +9 +52 +93 14 7593 759 0.00% 0.00% 0.00% 100.00% +11 +47 +82 13 11389 1138 0.00% 0.00% 0.00% 100.00% -9 +27 +74 13 17083 1708 0.00% 0.00% 0.00% 100.00% -13 +25 +66 14 25624 2562 0.00% 0.00% 0.00% 100.00% -8 +28 +65 13 38436 3843 0.00% 0.00% 0.00% 100.00% -13 +28 +69 13 57654 5765 0.00% 0.00% 0.00% 100.00% -11 +32 +71 14 86481 8648 0.00% 0.00% 0.00% 100.00% +2 +44 +83 14 129721 12972 15.36% 0.00% 0.35% 84.29% -2 +2248 +22907 4252 194581 16384 42.98% 0.00% 1.98% 55.04% -4 +5278 +65039 5856 291871 16384 54.33% 0.00% 2.21% 43.46% -3 +6306 +22608 5665 We can see that with 4 registers, as expected, we are able to handle a increasing number of requests more consistently, but as soon as all registers are in use, the decrease in quality of service happens in a sharp step. Signed-off-by: Vinicius Costa Gomes <[email protected]> Reviewed-by: Vladimir Oltean <[email protected]> Reviewed-by: Muhammad Husaini Zulkifli <[email protected]> Reviewed-by: Kurt Kanzenbach <[email protected]> Tested-by: Naama Meir <[email protected]> Signed-off-by: Tony Nguyen <[email protected]>
2023-08-24net: dsa: use capital "OR" for multiple licenses in SPDXKrzysztof Kozlowski4-4/+4
Documentation/process/license-rules.rst and checkpatch expect the SPDX identifier syntax for multiple licenses to use capital "OR". Correct it to keep consistent format and avoid copy-paste issues. Signed-off-by: Krzysztof Kozlowski <[email protected]> Reviewed-by: Kurt Kanzenbach <[email protected]> Reviewed-by: FLorian Fainelli <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2023-08-24Merge branch 'mlx5-next' of ↵Jakub Kicinski15-1618/+2583
https://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux Leon Romanovsky says: ==================== mlx5 MACsec RoCEv2 support From Patrisious: This series extends previously added MACsec offload support to cover RoCE traffic either. In order to achieve that, we need configure MACsec with offload between the two endpoints, like below: REMOTE_MAC=10:70:fd:43:71:c0 * ip addr add 1.1.1.1/16 dev eth2 * ip link set dev eth2 up * ip link add link eth2 macsec0 type macsec encrypt on * ip macsec offload macsec0 mac * ip macsec add macsec0 tx sa 0 pn 1 on key 00 dffafc8d7b9a43d5b9a3dfbbf6a30c16 * ip macsec add macsec0 rx port 1 address $REMOTE_MAC * ip macsec add macsec0 rx port 1 address $REMOTE_MAC sa 0 pn 1 on key 01 ead3664f508eb06c40ac7104cdae4ce5 * ip addr add 10.1.0.1/16 dev macsec0 * ip link set dev macsec0 up And in a similar manner on the other machine, while noting the keys order would be reversed and the MAC address of the other machine. RDMA traffic is separated through relevant GID entries and in case of IP ambiguity issue - meaning we have a physical GIDs and a MACsec GIDs with the same IP/GID, we disable our physical GID in order to force the user to only use the MACsec GID. v0: https://lore.kernel.org/netdev/[email protected]/ * 'mlx5-next' of https://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux: RDMA/mlx5: Handles RoCE MACsec steering rules addition and deletion net/mlx5: Add RoCE MACsec steering infrastructure in core net/mlx5: Configure MACsec steering for ingress RoCEv2 traffic net/mlx5: Configure MACsec steering for egress RoCEv2 traffic IB/core: Reorder GID delete code for RoCE net/mlx5: Add MACsec priorities in RDMA namespaces RDMA/mlx5: Implement MACsec gid addition and deletion net/mlx5: Maintain fs_id xarray per MACsec device inside macsec steering net/mlx5: Remove netdevice from MACsec steering net/mlx5e: Move MACsec flow steering and statistics database from ethernet to core net/mlx5e: Rename MACsec flow steering functions/parameters to suit core naming style net/mlx5: Remove dependency of macsec flow steering on ethernet net/mlx5e: Move MACsec flow steering operations to be used as core library macsec: add functions to get macsec real netdevice and check offload ==================== Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2023-08-24Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski38-123/+144
Cross-merge networking fixes after downstream PR. Conflicts: include/net/inet_sock.h f866fbc842de ("ipv4: fix data-races around inet->inet_id") c274af224269 ("inet: introduce inet->inet_flags") https://lore.kernel.org/all/[email protected]/ Adjacent changes: drivers/net/bonding/bond_alb.c e74216b8def3 ("bonding: fix macvlan over alb bond support") f11e5bd159b0 ("bonding: support balance-alb with openvswitch") drivers/net/ethernet/broadcom/bgmac.c d6499f0b7c7c ("net: bgmac: Return PTR_ERR() for fixed_phy_register()") 23a14488ea58 ("net: bgmac: Fix return value check for fixed_phy_register()") drivers/net/ethernet/broadcom/genet/bcmmii.c 32bbe64a1386 ("net: bcmgenet: Fix return value check for fixed_phy_register()") acf50d1adbf4 ("net: bcmgenet: Return PTR_ERR() for fixed_phy_register()") net/sctp/socket.c f866fbc842de ("ipv4: fix data-races around inet->inet_id") b09bde5c3554 ("inet: move inet->mc_loop to inet->inet_frags") Signed-off-by: Jakub Kicinski <[email protected]>
2023-08-24Merge tag 'mlx5-updates-2023-08-22' of ↵Paolo Abeni7-303/+371
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux Saeed Mahameed says: ==================== mlx5-updates-2023-08-22 1) Patches #1..#13 From Jiri: The goal of this patchset is to make the SF code cleaner. Benefit from previously introduced devlink_port struct containerization to avoid unnecessary lookups in devlink port ops. Also, benefit from the devlink locking changes and avoid unnecessary reference counting. 2) Patches #14,#15: Add ability to configure proto both UDP and TCP selectors in RX and TX directions. * tag 'mlx5-updates-2023-08-22' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux: net/mlx5e: Support IPsec upper TCP protocol selector net/mlx5e: Support IPsec upper protocol selector field offload for RX net/mlx5: Store vport in struct mlx5_devlink_port and use it in port ops net/mlx5: Check vhca_resource_manager capability in each op and add extack msg net/mlx5: Relax mlx5_devlink_eswitch_get() return value checking net/mlx5: Return -EOPNOTSUPP in mlx5_devlink_port_fn_migratable_set() directly net/mlx5: Reduce number of vport lookups passing vport pointer instead of index net/mlx5: Embed struct devlink_port into driver structure net/mlx5: Don't register ops for non-PF/VF/SF port and avoid checks in ops net/mlx5: Remove no longer used mlx5_esw_offloads_sf_vport_enable/disable() net/mlx5: Introduce mlx5_eswitch_load/unload_sf_vport() and use it from SF code net/mlx5: Allow mlx5_esw_offloads_devlink_port_register() to register SFs net/mlx5: Push devlink port PF/VF init/cleanup calls out of devlink_port_register/unregister() net/mlx5: Push out SF devlink port init and cleanup code to separate helpers net/mlx5: Rework devlink port alloc/free into init/cleanup ==================== Link: https://lore.kernel.org/all/[email protected]/ Signed-off-by: Paolo Abeni <[email protected]>
2023-08-24bonding: fix macvlan over alb bond supportHangbin Liu1-3/+3
The commit 14af9963ba1e ("bonding: Support macvlans on top of tlb/rlb mode bonds") aims to enable the use of macvlans on top of rlb bond mode. However, the current rlb bond mode only handles ARP packets to update remote neighbor entries. This causes an issue when a macvlan is on top of the bond, and remote devices send packets to the macvlan using the bond's MAC address as the destination. After delivering the packets to the macvlan, the macvlan will rejects them as the MAC address is incorrect. Consequently, this commit makes macvlan over bond non-functional. To address this problem, one potential solution is to check for the presence of a macvlan port on the bond device using netif_is_macvlan_port(bond->dev) and return NULL in the rlb_arp_xmit() function. However, this approach doesn't fully resolve the situation when a VLAN exists between the bond and macvlan. So let's just do a partial revert for commit 14af9963ba1e in rlb_arp_xmit(). As the comment said, Don't modify or load balance ARPs that do not originate locally. Fixes: 14af9963ba1e ("bonding: Support macvlans on top of tlb/rlb mode bonds") Reported-by: [email protected] Closes: https://bugzilla.redhat.com/show_bug.cgi?id=2117816 Signed-off-by: Hangbin Liu <[email protected]> Acked-by: Jay Vosburgh <[email protected]> Signed-off-by: Paolo Abeni <[email protected]>
2023-08-23net: ethernet: mtk_eth_soc: support 36-bit DMA addressing on MT7988Daniel Golle2-4/+48
Systems having 4 GiB of RAM and more require DMA addressing beyond the current 32-bit limit. Starting from MT7988 the hardware now supports 36-bit DMA addressing, let's use that new capability in the driver to avoid running into swiotlb on systems with 4 GiB of RAM or more. Signed-off-by: Daniel Golle <[email protected]> Link: https://lore.kernel.org/r/95b919c98876c9e49761e44662e7c937479eecb8.1692721443.git.daniel@makrotopia.org Signed-off-by: Jakub Kicinski <[email protected]>
2023-08-23net: ethernet: mtk_eth_soc: add support for in-SoC SRAMDaniel Golle2-22/+78
MT7981, MT7986 and MT7988 come with in-SoC SRAM dedicated for Ethernet DMA rings. Support using the SRAM without breaking existing device tree bindings, ie. only new SoC starting from MT7988 will have the SRAM declared as additional resource in device tree. For MT7981 and MT7986 an offset on top of the main I/O base is used. Signed-off-by: Daniel Golle <[email protected]> Link: https://lore.kernel.org/r/e45e0f230c63ad58869e8fe35b95a2fb8925b625.1692721443.git.daniel@makrotopia.org Signed-off-by: Jakub Kicinski <[email protected]>
2023-08-23net: ethernet: mtk_eth_soc: add reset bits for MT7988Daniel Golle2-24/+68
Add bits needed to reset the frame engine on MT7988. Fixes: 445eb6448ed3 ("net: ethernet: mtk_eth_soc: add basic support for MT7988 SoC") Signed-off-by: Daniel Golle <[email protected]> Link: https://lore.kernel.org/r/89b6c38380e7a3800c1362aa7575600717bc7543.1692721443.git.daniel@makrotopia.org Signed-off-by: Jakub Kicinski <[email protected]>
2023-08-23net: ethernet: mtk_eth_soc: fix register definitions for MT7988Daniel Golle1-3/+5
More register macros need to be adjusted for the 3rd GMAC on MT7988. Account for added bit in SYSCFG0_SGMII_MASK. Fixes: 445eb6448ed3 ("net: ethernet: mtk_eth_soc: add basic support for MT7988 SoC") Signed-off-by: Daniel Golle <[email protected]> Reviewed-by: Simon Horman <[email protected]> Link: https://lore.kernel.org/r/1c8da012e2ca80939906d85f314138c552139f0f.1692721443.git.daniel@makrotopia.org Signed-off-by: Jakub Kicinski <[email protected]>
2023-08-23net: fec: add exception tracing for XDPWei Fang1-15/+11
As we already added the exception tracing for XDP_TX, I think it is necessary to add the exception tracing for other XDP actions, such as XDP_REDIRECT, XDP_ABORTED and unknown error actions. Signed-off-by: Wei Fang <[email protected]> Suggested-by: Jakub Kicinski <[email protected]> Reviewed-by: Jacob Keller <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2023-08-23net: dm9051: Use PTR_ERR_OR_ZERO() to simplify codeYu Liao1-3/+1
Use the standard error pointer macro to shorten the code and simplify. Signed-off-by: Yu Liao <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2023-08-23wifi: ath12k: Fix memory leak in rx_desc and tx_descRajat Soni2-1/+31
Currently when ath12k_dp_cc_desc_init() is called we allocate memory to rx_descs and tx_descs. In ath12k_dp_cc_cleanup(), during descriptor cleanup rx_descs and tx_descs memory is not freed. This is cause of memory leak. These allocated memory should be freed in ath12k_dp_cc_cleanup. In ath12k_dp_cc_desc_init(), we can save base address of rx_descs and tx_descs. In ath12k_dp_cc_cleanup(), we can free rx_descs and tx_descs memory using their base address. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Signed-off-by: Rajat Soni <[email protected]> Signed-off-by: Kalle Valo <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2023-08-23wifi: ath5k: ath5k_hw_get_median_noise_floor(): use swap()Mahmoud Maatuq1-16/+13
coccinielle reported the following: ./drivers/net/wireless/ath/ath5k/phy.c:1573:25-26: WARNING opportunity for swap() while trying to fix the above warning, it reveals that ath5k_hw_get_median_noise_floor() had open-coded sort() functionality. Since ath5k_hw_get_median_noise_floor() only executes once every 10 seconds, any extra overhead due to sort() calling its "compare" and "swap" functions can be ignored, so replace the existing logic with a call to sort(). Signed-off-by: Mahmoud Maatuq <[email protected]> Suggested-by: Jiri Slaby <[email protected]> Signed-off-by: Kalle Valo <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2023-08-23wifi: ath: remove unused-but-set parameterArnd Bergmann4-6/+2
This has never been used since the driver was merged, but it now causes a W=1 warning in recent clang versions drivers/net/wireless/ath/ath9k/main.c:1566:21: error: parameter 'changed_flags' set but not used [-Werror,-Wunused-but-set-parameter] drivers/net/wireless/ath/ath9k/htc_drv_main.c:1258:25: error: parameter 'changed_flags' set but not used [-Werror,-Wunused-but-set-parameter] drivers/net/wireless/ath/ath5k/mac80211-ops.c:367:62: error: parameter 'changed_flags' set but not used [-Werror,-Wunused-but-set-parameter] Remove the bit manipulation on the otherwise unused parameter. Signed-off-by: Arnd Bergmann <[email protected]> Reviewed-by: Jeff Johnson <[email protected]> Acked-by: Toke Høiland-Jørgensen <[email protected]> Signed-off-by: Kalle Valo <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2023-08-23wifi: ath11k: Remove unused declarationsYue Haibing2-5/+0
Commit 2c3960c2253d ("ath11k: setup ce tasklet for control path") declared but never implemented ath11k_ce_map_service_to_pipe(). Commit e3396b8bddd2 ("ath11k: ce: support different CE configurations") declared but never implemented ath11k_ce_attr_attach(). Commit d5c65159f289 ("ath11k: driver for Qualcomm IEEE 802.11ax devices") declared but never implemented ath11k_qmi_event_work()/ath11k_qmi_msg_recv_work(). Signed-off-by: Yue Haibing <[email protected]> Acked-by: Jeff Johnson <[email protected]> Signed-off-by: Kalle Valo <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2023-08-23wifi: ath10k: fix Wvoid-pointer-to-enum-cast warningKrzysztof Kozlowski1-1/+1
'hw_rev' is an enum, thus cast of pointer on 64-bit compile test with W=1 causes: ath10k/ahb.c:736:11: error: cast to smaller integer type 'enum ath10k_hw_rev' from 'const void *' [-Werror,-Wvoid-pointer-to-enum-cast] Signed-off-by: Krzysztof Kozlowski <[email protected]> Acked-by: Jeff Johnson <[email protected]> Signed-off-by: Kalle Valo <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2023-08-23wifi: ath11k: fix Wvoid-pointer-to-enum-cast warningKrzysztof Kozlowski1-1/+1
'hw_rev' is an enum, thus cast of pointer on 64-bit compile test with W=1 causes: h11k/ahb.c:1124:11: error: cast to smaller integer type 'enum ath11k_hw_rev' from 'const void *' [-Werror,-Wvoid-pointer-to-enum-cast] Signed-off-by: Krzysztof Kozlowski <[email protected]> Acked-by: Jeff Johnson <[email protected]> Signed-off-by: Kalle Valo <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2023-08-23wifi: ath11k: simplify the code with module_platform_driverYang Yingliang1-11/+1
The init/exit() of driver only calls platform_driver_register/unregister, it can be simpilfied with module_platform_driver. Signed-off-by: Yang Yingliang <[email protected]> Signed-off-by: Kalle Valo <[email protected]> Link: https://lore.kernel.org/r/[email protected]
Powered by cgit, Gruvboxed by Blaster4385.