| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This patch introduces a new function ice_dcb_rebuild which reinitializes
DCB after a reset.
Signed-off-by: Anirudh Venkataramanan <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
This patch adds a new function ice_update_dcb_stats to get DCB stats
from the hardware and ethtool support for displaying these stats.
Signed-off-by: Anirudh Venkataramanan <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
This patch introduces a new function ice_tx_prepare_vlan_flags_dcb to
insert 802.1p priority information into the VLAN header
Signed-off-by: Anirudh Venkataramanan <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
This patch adds a new function ice_vsi_cfg_dcb_rings which updates a
VSI's rings based on DCB traffic class information.
Signed-off-by: Anirudh Venkataramanan <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
This patch adds support to process LLDP MIB change notifications sent
by the firmware.
Signed-off-by: Anirudh Venkataramanan <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
When the firmware doesn't support LLDP or DCBX, the driver should switch
to "software LLDP mode". This patch adds support for the same.
Signed-off-by: Anirudh Venkataramanan <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
This patch adds a new function ice_pf_dcb_cfg (and related helpers)
which applies the DCB configuration obtained from the firmware. As
part of this, VSIs/netdevs are updated with traffic class information.
This patch requires a bit of a refactor of existing code.
1. For a MIB change event, the associated VSI is closed and brought up
again. The gap between closing and opening the VSI can cause a race
condition. Fix this by grabbing the rtnl_lock prior to closing the
VSI and then only free it after re-opening the VSI during a MIB
change event.
2. ice_sched_query_elem is used in ice_sched.c and with this patch, in
ice_dcb.c as well. However, ice_dcb.c is not built when CONFIG_DCB is
unset. This results in namespace warnings (ice_sched.o: Externally
defined symbols with no external references) when CONFIG_DCB is unset.
To avoid this move ice_sched_query_elem from ice_sched.c to
ice_common.c.
Signed-off-by: Anirudh Venkataramanan <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
This patch introduces a new top level function ice_init_dcb (and
related lower level helper functions) which continues the DCB init
flow.
This function uses ice_get_dcb_cfg to get, parse and store the DCB
configuration. Once this is done, it sets itself up to be notified
by the firmware on LLDP MIB change events.
Reviewed-by: Bruce Allan <[email protected]>
Signed-off-by: Anirudh Venkataramanan <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
This patch introduces a skeleton for ice_init_pf_dcb, the top level
function for DCB initialization. Subsequent patches will add to this
DCB init flow.
In this patch, ice_init_pf_dcb checks if DCB is a supported capability.
If so, an admin queue call to start the LLDP and DCBx in firmware is
issued. If not, an error is reported. Note that we don't fail the driver
init if DCB init fails.
Reviewed-by: Bruce Allan <[email protected]>
Signed-off-by: Anirudh Venkataramanan <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
Bump driver version to 0.7.3
Signed-off-by: Anirudh Venkataramanan <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
Capitalize abbreviations and spell out some that aren't obvious.
Reviewed-by: Bruce Allan <[email protected]>
Signed-off-by: Anirudh Venkataramanan <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
This patch fixes typos in code comments.
Reviewed-by: Bruce Allan <[email protected]>
Signed-off-by: Anirudh Venkataramanan <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
Somehow file drivers/net/wireless/realtek/rtlwifi/rtl8188ee/trx.c.rej was
incorporated into the sources. Obviously, it can be removed.
Signed-off-by: Larry Finger <[email protected]>
Reported-by: Andrew Morton <[email protected]>
Cc: Andrew Morton <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
|
|
There are a couple of spelling mistakes in NL_SET_ERR_MSG_MOD error
messages. Fix these.
Signed-off-by: Colin Ian King <[email protected]>
Acked-by: Jakub Kicinski <[email protected]>
Reviewed-by: Mukesh Ojha <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
gcc warn this:
drivers/net/ethernet/stmicro/stmmac/norm_desc.c: In function ndesc_init_rx_desc:
drivers/net/ethernet/stmicro/stmmac/norm_desc.c:138:6: warning: variable 'bfsize1' set but not used [-Wunused-but-set-variable]
Like enh_desc_init_rx_desc, we should use bfsize1
in ndesc_init_rx_desc to calculate 'p->des1'
Fixes: 583e63614149 ("net: stmmac: use correct DMA buffer size in the RX descriptor")
Signed-off-by: YueHaibing <[email protected]>
Reviewed-by: Aaro Koskinen <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Conflict resolution of af_smc.c from Stephen Rothwell.
Signed-off-by: David S. Miller <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2019-04-16
This series contains updates to i40e driver only.
Adam fixes i40e so that queues can be restored to its original value if
configuring queue channels fails. Bumped the maximum API version
supported and added the API version to error messages to clarify
supported firmware API versions. Fixed the problem with the driver
being able to add only 7 multicast MAC address filters instead of 16.
Aleksandr adds support for Dynamic Device Personalization (DDP) which
allows loading profiles that change the way internal parser interprets
processed frames.
Nick fixes an issue where if we modify the VLAN stripping options when a
port VLAN is configured, it will break traffic for the VSI, so prevent
changes from being made.
Jake fixes an issue where a device reset can mess up the clock time
because we reset the clock time based on the kernel time every reset.
This causes us to potentially completely reset the PTP time, and can
cause unexpected behavior in programs like ptp4l.
Piotr fixes an LED blink issue with the 'ethtool -p' command, so that
identification blinking will work on all hardware.
Chinh fixed the error returned to correctly reflect the current state
when LLDP or DCBx is not in an operational state.
Grzegorz cleans up a misleading error message when untrusted VF tries to
exceed addresses beyond the NIC limit.
Carolyn fixes the error return code to correctly reflect the error case.
v2: updated the URL provided in the DDP patch (#2)
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
By default Flow Control feature is not being enabled in stmmac.
This is a useful feature that can prevent loss of packets and now that
XGMAC already supports it (along with GMAC and QoS) it makes sense to
activate it.
Switch the module parameter to FLOW_AUTO so that Flow Control is
activated.
Signed-off-by: Jose Abreu <[email protected]>
Cc: Joao Pinto <[email protected]>
Cc: David S. Miller <[email protected]>
Cc: Giuseppe Cavallaro <[email protected]>
Cc: Alexandre Torgue <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Finish the implementation of Flow Control feature. In order for it to
work correctly we need to set EHFC bit and the correct threshold values
for activating and deactivating it.
Signed-off-by: Jose Abreu <[email protected]>
Cc: Joao Pinto <[email protected]>
Cc: David S. Miller <[email protected]>
Cc: Giuseppe Cavallaro <[email protected]>
Cc: Alexandre Torgue <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
On platforms that lack a TCAM (like LS1088A), masking of
flow steering keys is not supported. Until now we didn't
offer flow steering capabilities at all on these platforms,
since our driver implementation configured a "comprehensive"
FS key (containing all supported header fields), with masks
used to ignore the fields not present in the rules provided
by the user.
We now allow ethtool rules that share a common key (i.e. have
the same header fields). The FS key is now kept in the driver
private data and initialized when the first rule is added to
an empty table, rather than at probe time. If a rule with a new
composition key is wanted, the user must first manually delete
all previous rules.
When building a FS table entry to pass to firmware, we still use
the old building algorithm, which assumes an all-supported-fields
key, and later collapse the fields which aren't actually needed.
Masked rules are not supported; if provided, the mask value
will be ignored. For firmware versions older than MC10.7.0
(that only offer the legacy ABIs for configuring distribution
keys) flow steering without masking support remains unavailable.
Signed-off-by: Ioana Radulescu <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Introduce an internal id bitfield to uniquely identify header fields
supported by the Rx distribution keys. For the hash key, add a
conversion from the RXH_* bitmask provided by ethtool to the internal
ids.
Signed-off-by: Ioana Radulescu <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Add two macros to simplify reading DPNI options.
Signed-off-by: Ioana Radulescu <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Set the Rx flow classification enable flag only if key config
operation is successful.
Fixes 3f9b5c9 ("dpaa2-eth: Configure Rx flow classification key")
Signed-off-by: Ioana Radulescu <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This is preventive cleanup that may save troubles later.
No need to cancel repeateadly queued work if code is properly
refactored.
Don't let the ethtool -s process interfere with the stat workqueue
scheduling.
Signed-off-by: Claudiu Manoil <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Preemption disabled at:
[<ffff000008cabd54>] dev_set_rx_mode+0x1c/0x38
Call trace:
[<ffff00000808a5c0>] dump_backtrace+0x0/0x3d0
[<ffff00000808a9a4>] show_stack+0x14/0x20
[<ffff000008e6c0c0>] dump_stack+0xac/0xe4
[<ffff0000080fe76c>] ___might_sleep+0x164/0x238
[<ffff0000080fe890>] __might_sleep+0x50/0x88
[<ffff0000082261e4>] kmem_cache_alloc+0x17c/0x1d0
[<ffff000000ea0ae8>] ocelot_set_rx_mode+0x108/0x188 [mscc_ocelot_common]
[<ffff000008cabcf0>] __dev_set_rx_mode+0x58/0xa0
[<ffff000008cabd5c>] dev_set_rx_mode+0x24/0x38
Fixes: a556c76adc05 ("net: mscc: Add initial Ocelot switch support")
Signed-off-by: Claudiu Manoil <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The nfp_flower_copy_pre_actions function introduces a case statement with
an intentional fallthrough. However, this generates a warning if built
with the -Wimplicit-fallthrough flag.
Remove the warning by adding a fall through comment.
Fixes: 1c6952ca587d ("nfp: flower: generate merge flow rule")
Signed-off-by: John Hurley <[email protected]>
Reported-by: Stephen Rothwell <[email protected]>
Reviewed-by: Jiong Wang <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
There is a spelling mistake in a DP_INFO message, fix it.
Signed-off-by: Colin Ian King <[email protected]>
Reviewed-by: Mukesh Ojha <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The Micrel KSZ9031 PHY may fail to establish a link when the Asymmetric
Pause capability is set. This issue is described in a Silicon Errata
(DS80000691D or DS80000692D), which advises to always disable the
capability. This patch implements the workaround by defining a KSZ9031
specific get_feature callback to force the Asymmetric Pause capability
bit to be cleared.
This fixes issues where the link would not come up at boot time, or when
the Asym Pause bit was set later on.
Signed-off-by: Antoine Tenart <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The patch adds support for detecting the P2P (peer-to-peer) event packets.
This is required for timestamping the PTP packets in peer delay mode.
Unmask the below bits (set to 0) for device to detect the p2p packets.
NIG_REG_P0/1_LLH_PTP_PARAM_MASK
NIG_REG_P0/1_TLLH_PTP_PARAM_MASK
bit 1 - IPv4 DA 1 of 224.0.0.107.
bit 3 - IPv6 DA 1 of 0xFF02:0:0:0:0:0:0:6B.
bit 9 - MAC DA 1 of 0x01-80-C2-00-00-0E.
NIG_REG_P0/1_LLH_PTP_RULE_MASK
NIG_REG_P0/1_TLLH_PTP_RULE_MASK
bit 2 - {IPv4 DA 1; UDP DP 0}
bit 6 - MAC Ethertype 0 of 0x88F7.
bit 9 - MAC DA 1 of 0x01-80-C2-00-00-0E.
Signed-off-by: Sudarsana Reddy Kalluru <[email protected]>
Signed-off-by: Ariel Elior <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This patch performs code cleanup by defining macros for the ptp-timestamp
filters.
Signed-off-by: Sudarsana Reddy Kalluru <[email protected]>
Signed-off-by: Ariel Elior <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warning:
drivers/net/xen-netfront.c: In function ‘netback_changed’:
drivers/net/xen-netfront.c:2038:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (dev->state == XenbusStateClosed)
^
drivers/net/xen-netfront.c:2041:2: note: here
case XenbusStateClosing:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
Notice that, in this particular case, the code comment is modified
in accordance with what GCC is expecting to find.
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <[email protected]>
Reviewed-by: Juergen Gross <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This patch changes an error code for an admin queue
head overrun to use I40E_ERR_ADMIN_QUEUE_FULL instead
of I40E_ERR_QUEUE_EMPTY.
Signed-off-by: Carolyn Wyborny <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
This patch fixes the problem with the driver being able to add only 7
multicast MAC address filters instead of 16. The problem is fixed by
changing the maximum number of MAC address filters to 16+1+1 (two extra
are needed because the driver uses 1 for unicast MAC address and 1 for
broadcast).
Signed-off-by: Adam Ludkiewicz <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
Defined the advertised link mode field for 40000baseSR4_Full for
use with ethtool.
Signed-off-by: Adam Ludkiewicz <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
Added the API version in the error message for clarity.
Signed-off-by: Adam Ludkiewicz <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
A new FW has been released, which uses API version 1.8.
Signed-off-by: Adam Ludkiewicz <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
Removed misleading messages when untrusted VF tries to
add more addresses than NIC limit
Signed-off-by: Grzegorz Siwik <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
Modify the i40e_init_dcb to return the correct error when LLDP or DCBX
is not in operational state.
Signed-off-by: Chinh T Cao <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
On some hardware LEDs would not blink after command 'ethtool -p {eth-port}'
in certain circumstances. Now, function does not care about the activity
of the LED (though still preserves its state) but forcibly executes
identification blinking and then restores the LED state.
Signed-off-by: Piotr Marczak <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
In the case where PTP is running on the hardware clock, but the kernel
system time is not being synced, a device reset can mess up the clock
time.
This occurs because we reset the clock time based on the kernel time
every reset. This causes us to potentially completely reset the PTP
time, and can cause unexpected behavior in programs like ptp4l.
Avoid this by saving the PTP time prior to device reset, and then
restoring using that time after the reset.
Directly restoring the PTP time we saved isn't perfect, because time
should have continued running, but the clock will essentially be stopped
during the reset. This is still better than the current solution of
assuming that the PTP HW clock is synced to the CLOCK_REALTIME.
We can do even better, by saving the ktime and calculating
a differential, using ktime_get(). This is based on CLOCK_MONOTONIC, and
allows us to get a fairly precise measure of the time difference between
saving and restoring the time.
Using this, we can update the saved PTP time, and use that as the value
to write to the hardware clock registers. This, of course is not perfect.
However, it does help ensure that the PTP time is restored as close as
feasible to the time it should have been if the reset had not occurred.
During device initialization, continue using the system time as the
source for the creation of the PTP clock, since this is the best known
current time source at driver load.
Signed-off-by: Jacob Keller <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
Modifying the VLAN stripping options when a port VLAN is configured
will break traffic for the VSI, and conceptually doesn't make sense,
so don't allow this.
Signed-off-by: Nicholas Nunley <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
This patch introduces DDP (Dynamic Device Personalization) which allows
loading profiles that change the way internal parser interprets processed
frames. To load DDP profiles it utilizes ethtool flash feature. The files
with recipes must be located in /var/lib/firmware directory. Afterwards
the recipe can be loaded by invoking:
ethtool -f <if_name> <file_name> 100
ethtool -f <if_name> - 100
See further details of this feature in the i40e documentation, or
visit
https://www.intel.com/content/www/us/en/architecture-and-technology/ethernet/dynamic-device-personalization-brief.html
The driver shall verify DDP profile can be loaded in accordance with
the rules:
* Package with Group ID 0 are exclusive and can only be loaded the first.
* Packages with Group ID 0x01-0xFE can only be loaded simultaneously
with the packages from the same group.
* Packages with Group ID 0xFF are compatible with all other packages.
Signed-off-by: Aleksandr Loktionov <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
Added a new local variable in the i40e_setup_tc function named
old_queue_pairs so num_queue_pairs can be restored to the correct
value in case configuring queue channels fails. Additionally, moved
the exit label in the i40e_setup_tc function so the if (need_reset)
block can be executed.
Also, fixed data packing in the i40e_setup_tc function.
Signed-off-by: Adam Ludkiewicz <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
There is a spelling mistake in a BNX2X_ERR message, fix it.
Signed-off-by: Colin Ian King <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Recently genphy_read_abilities() has been added that dynamically detects
clause 22 PHY abilities. I *think* this detection should work with all
supported PHY's, at least for the ones with basic features sets, i.e.
PHY_BASIC_FEATURES and PHY_GBIT_FEATURES. So let's remove setting these
features explicitly and rely on phylib feature detection.
I don't have access to most of these PHY's, therefore I'd appreciate
regression testing.
v2:
- make the feature constant a comment so that readers know which
features are supported by the respective PHY
Signed-off-by: Heiner Kallweit <[email protected]>
Tested-by: Andrew Lunn <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
A merge flow is formed from 2 sub flows. The match fields of the merge are
the same as the first sub flow that has formed it, with the actions being
a combination of the first and second sub flow. Therefore, a merge flow
should replace sub flow 1 when offloaded.
Offload valid merge flows by using a new 'flow mod' message type to
replace an existing offloaded rule. Track the deletion of sub flows that
are linked to a merge flow and revert offloaded merge rules if required.
Signed-off-by: John Hurley <[email protected]>
Signed-off-by: Simon Horman <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
With the merging of 2 sub flows, a new 'merge' flow will be created and
written to FW. The TC layer is unaware that the merge flow exists and will
request stats from the sub flows. Conversely, the FW treats a merge rule
the same as any other rule and sends stats updates to the NFP driver.
Add links between merge flows and their sub flows. Use these links to pass
merge flow stats updates from FW to the underlying sub flows, ensuring TC
stats requests are handled correctly. The updating of sub flow stats is
done on (the less time critcal) TC stats requests rather than on FW stats
update.
Signed-off-by: John Hurley <[email protected]>
Signed-off-by: Simon Horman <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
When combining 2 sub_flows to a single 'merge flow' (assuming the merge is
valid), the merge flow should contain the same match fields as sub_flow 1
with actions derived from a combination of sub_flows 1 and 2. This action
list should have all actions from sub_flow 1 with the exception of the
output action that triggered the 'implicit recirculation' by sending to
an internal port, followed by all actions of sub_flow 2. Any pre-actions
in either sub_flow should feature at the start of the action list.
Add code to generate a new merge flow and populate the match and actions
fields based on the sub_flows. The offloading of the flow is left to
future patches.
Signed-off-by: John Hurley <[email protected]>
Signed-off-by: Simon Horman <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Two flows can be merged if the second flow (after recirculation) matches
on bits that are either matched on or explicitly set by the first flow.
This means that if a packet hits flow 1 and recirculates then it is
guaranteed to hit flow 2.
Add a 'can_merge' function that determines if 2 sub_flows in a merge hint
can be validly merged to a single flow.
Signed-off-by: John Hurley <[email protected]>
Signed-off-by: Simon Horman <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
If a merge hint is received containing 2 flows that are matched via an
implicit recirculation (sending to and matching on an internal port), fw
reports that the flows (called sub_flows) may be able to be combined to a
single flow.
Add infastructure to accept and process merge hint messages. The actual
merging of the flows is left as a stub call.
Signed-off-by: John Hurley <[email protected]>
Signed-off-by: Simon Horman <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|